19-0169; Rev 1; 11/05 ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors ____________________________Features The MAX8215 contains five voltage comparators; four are for monitoring +5V, -5V, +12V, and -12V, and the fifth monitors any desired voltage. The MAX8216 is identical, except it monitors ±15V supplies instead of ±12V. The resistors required to monitor these voltages and provide comparator hysteresis are included onchip. All comparators have open-drain outputs. These devices consume 250µA max supply current over temperature. ♦ 4 Dedicated Comparators plus 1 Auxiliary Comparator ♦ 5V Dedicated Comparator Has ±1.25% Accuracy ♦ -5V, +12V, -12V, +15V, -15V Dedicated Comparators Have ±1.5% Accuracy ♦ Overvoltage/Undervoltage Detection or Programmable Delay Using Auxiliary Comparator ♦ Internal 1.24V Reference with ±1% Initial Accuracy ♦ Wide Supply Range: 2.7V to 11V ♦ Built-In Hysteresis ♦ 250µA Max Supply Current Over Temp. ♦ Independent Open-Drain Outputs ♦ All Precision Components Included ________________________Applications Microprocessor Voltage Monitor +5V, -5V, +12V, -12V Supply Monitoring (MAX8215) +5V, -5V, +15V, -15V Supply Monitoring (MAX8216) Overvoltage/Undervoltage Detection with Uncommitted Comparator Industrial Controllers Mobile Radios Portable Instruments Industrial Equipment Data-Acquisition Systems __________Typical Operating Circuit 0.1µF +5V GND PGND +5V VDD OUT1 -5V MAX8215 MAX8216 OUT2 ______________Ordering Information PART TEMP RANGE MAX8215CPD 0°C to +70°C 14 Plastic DIP PIN-PACKAGE MAX8215CSD MAX8215C/D MAX8215EPD MAX8215ESD MAX8215EJD MAX8215MPD MAX8215MJD 0°C to +70°C 0°C to +70°C -40°C to +85°C -40°C to +85°C -40°C to +85°C -55°C to +125°C -55°C to +125°C 14 SO Dice* 14 Plastic DIP 14 SO 14 CERDIP 14 Plastic DIP 14 CERDIP *Dice are tested at TA = +25°C. Devices in PDIP and SO packages are available in both leaded and lead-free packaging. Specify lead free by adding the + symbol at the end of the part number when ordering. Lead free not available for CERDIP package. Ordering Information continued on last page. __________________Pin Configuration +12V (+15V) TOP VIEW OUT3 -12V (-15V) OUT4 VREF 1 GND 2 +5V 3 14 VDD 13 OUT1 MAX8215 MAX8216 -5V 4 DOUT DIN 12 OUT2 11 OUT3 +12V (+15V) 5 10 OUT4 -12V (-15V) 6 9 DOUT DIN 7 8 PGND DIP/SO ( ) ARE FOR MAX8216 ONLY. 1.24V REFERENCE VREF ( ) ARE FOR MAX8216 ONLY. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX8215/MAX8216 _______________General Description MAX8215/MAX8216 ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors ABSOLUTE MAXIMUM RATINGS VDD ............................................................................-0.3V, +12V VREF..............................................................-0.3V, (VDD + 0.3V) OUT_, DOUT Outputs....................................-0.3V, (VDD + 0.3V) +5V Input...................................................................+20V, -0.3V -5V, +12V, +15V, -12V, -15V Inputs.....................................±50V DIN Input .......................................................(VDD + 0.3V), -0.3V Continuous Power Dissipation (TA = +70°C) Plastic DIP (derate 10.00mW/°C above +70°C) ...........800mW SO (derate 8.33mW/°C above +70°C) ..........................667mW CERDIP (derate 9.09mW/°C above +70°C) ..................727mW Operating Temperature Ranges: MAX821_C_ _ ......................................................0°C to +70°C MAX821_E_ _....................................................-40°C to +85°C MAX821_M_ _ .................................................-55°C to +125°C Storage Temperature Range .............................-65°C to +165°C Lead Temperature (soldering, 10sec) .............................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VDD = +5V, GND = 0V, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER POWER SUPPLY CONDITIONS VDD Supply Voltage Range MIN TYP MAX MAX821_C 2.7 11 MAX821_E/M 2.85 11 IDD Supply Current 137 250 UNITS V µA REFERENCE OUTPUT TA = +25°C Output Voltage Tolerance Referred to 1.24V TA = TMIN to TMAX -1.00 1.00 MAX821_C -1.5 1.5 MAX821_E -1.75 1.75 MAX821_M -2.5 2.5 Load Current 40 % µA Load Regulation 3.3 Line Regulation 0.01 %/V 15 ppm/°C Output Tempco µV/µA COMPARATOR INPUTS VIN decreasing, TA = +25°C +5V Trip Level TA = TMIN to TMAX 4.521 4.500 4.657 MAX821_E 4.500 4.657 MAX821_M 4.464 4.693 4.636 TA = +25°C 1.25 TA = +125°C 1.75 TA = -55°C 0.8 VIN decreasing (MAX8215 only), TA = +25°C +12V Trip Level TA = TMIN to TMAX 2 TA = TMIN to TMAX 10.431 10.590 % 10.749 10.404 10.775 MAX821_E 10.378 10.802 MAX821_M 10.325 10.855 13.036 13.235 V 13.434 MAX821_C 13.003 13.467 MAX821_E 12.970 13.500 MAX821_M 12.904 13.566 _______________________________________________________________________________________ V 4.749 MAX821_C VIN decreasing (MAX8216 only), TA = +25°C +15V Trip Level 4.636 MAX821_C VIN increasing +5V Trip Level Hysteresis 4.579 V ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors MAX8215/MAX8216 ELECTRICAL CHARACTERISTICS (continued) (VDD = +5V, GND = 0V, TA = TMIN to TMAX, unless otherwise noted.) CONDITIONS PARAMETER I VIN I decreasing, TA = +25°C MAX821_C MAX821_E TA = TMIN to TMAX -12V Trip Level MAX821_M I VIN I decreasing (MAX8216 only), TA = +25°C -15V Trip Level -10.325 MAX821_E -12.970 -13.500 MAX821_M I VIN I decreasing, TA = +25°C MAX821_C -12.904 -4.348 -4.337 MAX821_E -4.326 -4.500 MAX821_M -4.304 -4.525 TA = +25°C V -10.855 -13.467 TA = +25°C UNITS -13.036 -13.235 -13.434 -4.415 -13.566 -4.482 -4.493 +15V trip level 1.25 2.00 +12V trip level 1.25 2.00 -15V trip level 1.50 2.25 -12V trip level 1.50 2.25 -5V trip level 1.60 2.25 +5V input to GND +12V/+15V input to GND -5V input to REF 0.005 130 168 160 Hysteresis Tempco, ±15, ±12, -5 Input Resistance MAX -13.003 TA = TMIN to TMAX Threshold Hysteresis TYP MAX821_C TA = TMIN to TMAX -5V Trip Level MIN -10.431 -10.590 -10.749 -10.404 -10.776 -10.378 -10.802 -12V/-15V input to REF V V % %/°C kΩ 190 AUXILIARY COMPARATOR INPUT Trip Level with Respect to 1.24V VIN decreasing, TA = +25°C MAX821_C MAX821_E MAX821_M Threshold Hysteresis TA = +25°C 1.25 2.00 % Input Bias Current TA = +25°C 2 10 nA VOL; VDD = 5V, ISINK = 2mA 0.11 0.3 VDD = 1.5V, ISINK = 0.2mA 0.04 0.3 V VDD = 1.0V, ISINK = 0.1mA 0.10 1.0 µA Voltage Output Low Leakage Current Off State Comparator Response Time (All Comparators) 30mV overdrive (Note 1) -1.5 -1.75 -2.00 -2.50 0 1.5 1.75 2.00 2.50 20 % µs VTHR Note 1: To overdrive the +5V/+12V/+15V comparators with a 30mV overdrive voltage, use the formula 30mV ( 1.24 ) to determine the required input voltage. VTHR is the threshold of the particular overdriven comparator. To overdrive the -5V/-12V/-15V comparators use 30mV [1+ I VTHR I ] . 1.24 _______________________________________________________________________________________ 3 __________________________________________Typical Operating Characteristics (TA=+25°C, unless otherwise noted.) COMPARATOR INPUT BIAS CURRENT vs. SUPPLY VOLTAGE 2 1.5 1 1.2 1 0.8 0.6 0.4 0.5 0.2 0 0 -60 -40 -20 0 TA = +125°C 1.5 5 0.5 2.5 3 3.5 4 4.5 5 0 2.0 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 SUPPLY CURRENT vs. SUPPLY VOLTAGE REFERENCE VOLTAGE vs. REFERENCE SOURCE CURRENT REFERENCE VOLTAGE vs. SUPPLY VOLTAGE TA = +125°C 135 -5V PIN = -5V -12V PIN = -5V +5V PIN = +5V +12V PIN = +12V 130 125 5 6 7 8 9 TA = +125°C 1.237 1.236 TA = +25°C 1.235 VDD = 5V 1.234 1.233 TA = -55°C 1.232 1.231 1.23 50 100 150 200 250 300 REFERENCE SOURCE CURRENT (µA) SUPPLY VOLTAGE (V) TA = -55°C 1.2 1.15 1.1 1.05 NOTE: -55°C IS WORST CASE CONDITION FOR REFERENCE REGULATION AT LOW VOLTAGES. 1 0.95 0 10 11 12 1.25 VREF, REFERENCE VOLTAGE (V) 140 VREF,REFERENCE VOLTAGE (V) TA = -55°C 145 1.238 MAX8215-TOC5 VOL (V) 150 4 10 SUPPLY VOLTAGE (V) TA = +25°C 3 20 TEMPERATURE (C°) 155 2 TA = +25°C 25 0 2 20 40 60 80 100 120 140 TA = -55°C 30 1 2 3 4 5 6 7 8 9 SUPPLY VOLTAGE (V) VREF OUTPUT VOLTAGE vs. TEMPERATURE MAX8215-TOC7 VREF, REFERENCE VOLTAGE (V) 1.238 1.237 VDD = 5V 1.236 1.235 1.234 1.233 1.232 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (°C) 4 MAX8215-TOC6 2.5 TA = +25°C 35 MAX8215-TOC3 1.4 INPUT BIAS CUREENT (nA) 3 MAX8215-TOC4 INPUT BIAS CURRENT (nA) 1.6 MAX8215-TOC2 VDD = 5V MAX8215-TOC1 4 3.5 OUTPUT VOLTAGE LOW vs. OUTPUT SINK CURRENT OUTPUT SINK CURRENT (mA) COMPARATOR INPUT BIAS CURRENT vs. TEMPERATURE SUPPLY CURRENT (µA) MAX8215/MAX8216 ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors _______________________________________________________________________________________ 10 11 ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors (TA = +25°C, unless otherwise noted.) +5V PIN 8215/16 SCOPE2 -5V RESPONSE WITH ±100mV INPUT EXCURSION AROUND TRIP LEVEL 8215/16 SCOPE1 +5V RESPONSE WITH ±100mV INPUT EXCURSION AROUND TRIP LEVEL +5V PIN OUT1 OUT1 +5V COMP -5V COMP SUPPLY VOLTAGE 8215/16 SCOPE4 DIN COMPARATOR RESPONSE WITH 30mV OVERDRIVE 8215/16 SCOPE3 DOUT OUTPUT VOLTAGE vs. SUPPLY VOLTAGE R1 = 15kΩ, R2 = 40k (see Figure 4) COMP OUTPUT COMP INPUT DOUT OUTPUT VOLTAGE DIN COMPARATOR RESPONSE WITH 50mV OVERDRIVE COMP OUTPUT COMP INPUT 8215/16 SCOPE6 8215/16 SCOPE5 DIN COMPARATOR RESPONSE WITH 100mV OVERDRIVE COMP OUTPUT COMP INPUT _______________________________________________________________________________________ 5 MAX8215/MAX8216 _____________________________Typical Operating Characteristics (continued) MAX8215/MAX8216 ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors _____________________Pin Description +5V PIN NAME FUNCTION 1 VREF Output of the internal 1.24V reference 2 GND Ground. Connect to PGND. 3 +5V Input for monitoring +5V supply 4 -5V Input for monitoring -5V supply 5 +12V (+15V) MAX8215 input for monitoring +12V (MAX8216 input for monitoring +15V) -12V (-15V) MAX8215 input for monitoring -12V (MAX8216 input for monitoring -15V) 6 OUT1 -5V MAX8215 MAX8216 +12V (+15V) OUT3 -12V (-15V) Noninverting input of the auxiliary comparator. Its inverting input is tied to the internal reference. Power-supply ground. Bypass VDD to this pin. 7 DIN 8 PGND 9 DOUT Output of the auxiliary comparator 10, 11, 12, 13 OUT4, OUT3, OUT2, OUT1 Outputs of the four dedicated comparators 14 VDD Power-supply positive voltage input. Bypass to PGND. OUT2 OUT4 DOUT DIN 1.24V REFERENCE ( ) ARE FOR MAX8216 ONLY. VREF VDD PGND GND Figure 1. Block Diagram _______________Detailed Description __________Applications Information The MAX8215/MAX8216 contain 5 comparators (Figure 1). The comparator with its output labeled DOUT is distinguished from the others in that it can be set up to monitor various voltages; each of the other 4 comparators monitors a specific voltage. The DOUT comparator’s noninverting input is available external to the device; its inverting input is tied internally to the reference. The MAX8215/MAX8216 comparators have open-drain outputs. Thus, these devices require pull-up resistors for proper operation. See the Typical Operating Circuit. Open-drain outputs are useful for driving LEDs and for situations in which the comparator outputs must be connected together (i.e., wire-ORed). Bypass VDD with 0.1µF connected to PGND. When the voltage on a typical comparator’s input is at or near the voltage on the other input, ambient noise generally causes the comparator output to oscillate. The most common way to eliminate this problem is by using hysteresis. When the two comparator input voltages are equal, hysteresis causes one comparator input voltage to move quickly past the other, thus taking the input out of the region where oscillation occurs. Standard comparators need external resistors for hysteresis; these resistors are not necessary when using any of the MAX8215 and MAX8216 comparators because hysteresis is built in. 6 Hysteresis _______________________________________________________________________________________ ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors MAX8215/MAX8216 VTRIP2 VDD MAX8215 MAX8216 RA 7 DIN ( INPUT VOLTAGE (VS) VTRIP1 180k DOUT 9 +VS VHYST 1 + RA RB ) GND OUTPUT VOLTAGE VDD RB GND 1.24V REFERENCE ( VTRIP = RA + RB RB ) TO DETERMINE THE TRIP VOLTAGES FROM PARTICULAR RESISTOR VALUES: RA VTRIP1 = VREF 1 + RB RA VTRIP2 = (VREF + VHYST) 1 + RB VHYST = 16mV TYP ) ( (VREF) Figure 2. Undervoltage/Overvoltage Comparator Using the Auxiliary Comparator Adding hysteresis to a comparator creates two trip points–one for the input voltage rising and one for the input voltage falling. When the voltage at the MAX8215/MAX8216 auxiliary comparator’s (noninverting) input falls, the threshold at which the comparator switches equals the reference voltage connected to the comparator’s inverting input. However, when the voltage at the noninverting input rises, the threshold equals the reference voltage plus the amount of hysteresis voltage built into the part. The trip point is somewhat more accurate when the hysteresis voltage is not part of the threshold voltage (i.e., when the input voltage is falling) because the tolerance of the hysteresis specification adds to the tolerance of the trip point. ( ) Figure 3. Undervoltage/Overvoltage Detector Waveforms and Formulas 0.1µF 8 2 GND 3 +VS +5V PGND MAX8215 MAX8216 VDD OUT1 14 13 UNDERVOLTAGE R1 7 Overvoltage and Undervoltage Detection Circuits Figure 2 shows connection of the auxiliary comparator as either an undervoltage or overvoltage comparator. Hysteresis makes this circuit more accurate when the input voltage is dropping as opposed to rising. Figure 3 illustrates the comparator’s operation. The input voltage’s direction determines at which of two trip points the comparator switches. Thus, the diagram includes arrows that indicate whether the input voltage is rising or falling. The formulas are provided for determining trip-point voltages for specified resistors and for ease in calculating appropriate resistor ratios for particular trip points. TO CALCULATE THE REQUIRED RESISTOR RATIOS FOR PARTICULAR TRIP VOLTAGES: RA VTRIP1 RB = VREF - 1 RA VTRIP2 RB = VREF + VHYST - 1 R2 DIN DOUT 9 OVERVOLTAGE +5V COMPARATOR IS ACTUATED WHEN VS FALLS TO THE COMPARATOR'S SPECIFIED TRIP LEVEL. THE AUXILIARY COMPARATOR OUTPUT IS TRIPPED WHEN VS > R1 + R2 VREF R2 ( ) Figure 4. Monitoring Supply Powering the MAX8215/MAX8216 with Undervoltage and Overvoltage Comparators The MAX8215/MAX8216 comparator outputs correctly display a low level down to 0.8V supply voltage. This is useful in undervoltage applications where the monitored power supply is also the supply connected to the VDD pin. See the section Monitoring the Supply Voltage. _______________________________________________________________________________________ 7 MAX8215/MAX8216 ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors +5V VTRIP2 INPUT VOLTAGE (VS) VTRIP1 0.1µF 8 2 GND +VS 3 7 +5V DIN PGND MAX8215 MAX8216 VDD OUT1 DOUT 14 680k 680k GND OUTPUT VOLTAGE (OUT1) 13 9 RESET OUTPUT VOLTAGE (DOUT) VDD tDLY GND VDD GND VTRIP1 IS FOR VS DECREASING; VTRIP2 IS FOR VS INCREASING. VREF tDLY = -RC In 1 - V CC ( ) 1µF NOTE: VTH IS THE VOLTAGE AT THE INVERTING PIN OF THE TWO COMPARATORS. IN THIS CASE, IT IS EQUAL TO THE INTERNAL REFERENCE VOLTAGE. Figure 5. Microprocessor Reset Circuit with 200ms Time Delay Monitoring the Supply Voltage The supply voltage to these devices can also be monitored by the 5V dedicated comparator and the auxiliary comparator. Figure 4 shows a circuit that monitors the voltage connected at V DD for both overvoltage and undervoltage conditions. The +5V comparator checks for undervoltage conditions while the auxiliary comparator monitors overvoltage conditions. In general, no extra supply bypassing circuitry (other than the normally recommended 0.1µF capacitor) is required when performing this function. However, using resistor values higher than 100kΩ at the auxiliary comparator’s input requires attention to eliminate potential oscillations. Also, particularly low pull-up resistor values on DOUT contribute to the likelihood of the auxiliary comparator’s oscillation. See the section Eliminating Output Oscillation. Microprocessor Reset ____________Circuit with Time Delay It is often necessary to reset a microprocessor (µP) when its supply voltage drops below a certain level. Figure 5’s circuit generates a low output when the monitored voltage drops below the 5V monitor’s threshold. Additionally, this output remains low for 200ms after the supply voltage goes above the threshold. µP reset circuits typically include this feature because it gives the µP time to be fully reset after power has been restored, and allows any capacitors in associated circuitry time to charge. Figure 6 shows this circuit’s waveforms and formulas. 8 Figure 6. Microprocessor Reset with Time Delay Waveforms Figure 7 shows Figure 5’s µP reset circuit, but with the monitored supply also powering the MAX8215. Figure 6’s waveforms and equations also apply to this circuit. The MAX8215/MAX8216 comparator outputs correctly display a low level down to a 0.8V typical supply voltage. Unused Inputs When the uncommitted comparator within the MAX8215/MAX8216 is not used, tie the unused input to either the positive supply or ground. This prevents noise generation due to the comparator output switching from one logic state to another (due to noise at the input). Output Pull-Up Resistors Pull-up resistors are required at the outputs of each comparator. Resistor values should not be less than 2.7kΩ if the outputs are pulled up to VDD. In general, save power by using higher values, e.g., ≥100kΩ. Use of higher-value resistors also minimizes the possibility of oscillations due to a spurious feedback (see the section Eliminating Output Oscillation). Input Voltage Limitation If the voltages at the various inputs are kept within the absolute maximum ratings, the device is not damaged. However, high input voltages within this range can cause the reference voltage to move. To prevent the reference voltage from changing, limit the +5V input to +17V; the -5V and -15V inputs to +1V; and the +15V input to +60V. Negative input voltages within the _______________________________________________________________________________________ ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors MAX8215/MAX8216 V+ +5V 1k 1k 0.1µF 14 0.1µF VDD OUT1 8 2 GND PGND VDD 14 680k 13 680k MAX8215 MAX8216 +VS 3 7 +5V DIN MAX8215 MAX8216 OUT1 DOUT 13 9 RESET Figure 8. Alternate Bypass Scheme 1µF Figure 7. Microprocessor Reset Circuit Monitoring Its Own Supply Voltage VIN 7 DIN MAX8215 MAX8216 DOUT 9 absolute maximum ratings have no effect on the reference. Within the absolute maximum ratings, the DIN input has no effect on the reference. Power-Supply Bypassing and Grounding In high-noise environments where the voltage connected to VDD may change abruptly, the reference voltage may “bounce,” causing false comparator outputs. Eliminate this problem using Figure 8’s RC bypass network. Although bypassing the reference may appear to help, Figure 8’s solution is recommended; bypassing the reference reduces its voltage change, but doing so causes a time delay prior to the reference voltage returning to its correct level. Figure 9. Alternative Means for Reducing Impedance Level Seen at DIN Eliminating Output Oscillation when Using the Auxiliary Comparator most cases, using input resistor values on the order of 100kΩ creates no problem. Since using lower resistor values increases the supply current, another approach is to bypass the input resistors as shown in Figure 9, although this slows the circuit’s response. When much larger valued input resistors are used, high valued resistors on the output should be used. Although hysteresis is built into the auxiliary comparator, output oscillation problems are still possible. Oscillation can occur when a comparator’s output couples back to its inverting input through stray board capacitance. Make sure the board trace leading from the comparator output does not pass near its inverting input (or vice versa). Also, reducing the resistance connected to DIN reduces its susceptibility to picking up output signals. In When DOUT is required to sink larger currents (i.e., when smaller pull-up resistor values are used), oscillation problems are more likely to occur. To minimize power consumption and to optimize stability, use the largest value pull-up resistor feasible for the output drive required. When lower pull-up resistor values are used, lower values for the resistors connected to the inputs can help alleviate oscillation problems. _______________________________________________________________________________________ 9 MAX8215/MAX8216 ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors _Ordering Information (continued) PART TEMP. RANGE MAX8216CPD 0°C to +70°C 14 Plastic DIP MAX8216CSD MAX8216C/D MAX8216EPD MAX8216ESD MAX8216EJD MAX8216MPD MAX8216MJD 0°C to +70°C 0°C to +70°C -40°C to +85°C -40°C to +85°C -40°C to +85°C -55°C to +125°C -55°C to +125°C 14 SO Dice* 14 Plastic DIP 14 SO 14 CERDIP 14 Plastic DIP 14 CERDIP * Dice are tested at TA = +25°C. ___________________Chip Topography PIN-PACKAGE GND VREF V DD OUT1 +5 OUT2 0.076" OUT3 (1.930mm) -5 +12V (+15V) OUT4 -12V (-15V) DIN PGND DOUT 0.066" (1.676mm) ( ) ARE FOR MAX8216 ONLY. TRANSISTOR COUNT: 275; SUBSTRATE CONNECTED TO VDD. 10 ______________________________________________________________________________________ ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors DIM D1 A A1 A2 A3 B B1 C D D1 E E1 e eA eB L α E E1 D A3 A A2 INCHES MIN MAX – 0.200 0.015 – 0.125 0.150 0.055 0.080 0.016 0.022 0.050 0.065 0.008 0.012 0.735 0.765 0.050 0.080 0.300 0.325 0.240 0.280 0.100 BSC 0.300 BSC – 0.400 0.115 0.150 0˚ 15˚ MILLIMETERS MIN MAX – 5.08 0.38 – 3.18 3.81 1.40 2.03 0.41 0.56 1.27 1.65 0.20 0.30 18.67 19.43 1.27 2.03 7.62 8.26 6.10 7.11 2.54 BSC 7.62 BSC – 10.16 2.92 3.81 0˚ 15˚ 21-330A L A1 α C e B1 B eA 14-PIN PLASTIC DUAL-IN-LINE PACKAGE eB ______________________________________________________________________________________ 11 MAX8215/MAX8216 ________________________________________________________Package Information MAX8215/MAX8216 ±5V, ±12V (±15V) Dedicated Microprocessor Voltage Monitors ___________________________________________Package Information (continued) DIM E A A1 B C D E e H h L α H INCHES MAX MIN 0.069 0.053 0.010 0.004 0.019 0.014 0.010 0.007 0.344 0.337 0.157 0.150 0.050 BSC 0.244 0.228 0.020 0.010 0.050 0.016 8˚ 0˚ MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 8.55 8.75 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.27 0˚ 8˚ 21-331A h x 45˚ D α A 0.127mm 0.004in. e B A1 C L 14-PIN PLASTIC SMALL-OUTLINE PACKAGE Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 © 2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc.