FUJITSU MB96F348CSB

FUJITSU SEMICONDUCTOR
DATA SHEET
FME-MB96340 rev 10
16-bit Proprietary Microcontroller
CMOS
F2MC-16FX MB96340 Series
MB96345/346 MB96F345 *1
MB96F346/F347/F348
■ DESCRIPTION
MB96340 series is based on Fujitsu’s advanced 16FX architecture (16-bit with instruction pipeline for RISC-like
performance). The CPU uses the same instruction set as the established 16LX series - thus allowing for easy
migration of 16LX Software to the new 16FX products. 16FX improvements compared to the previous generation
include significantly improved performance - even at the same operation frequency, reduced power consumption
and faster start-up time.
For highest processing speed at optimized power consumption an internal PLL can be selected to supply the
CPU with up to 56MHz operation frequency from an external 4MHz resonator. The result is a minimum instruction
cycle time of 17.8ns going together with excellent EMI behavior. An on-chip clock modulation circuit significantly
reduces emission peaks in the frequency spectrum. The emitted power is minimized by the on-chip voltage
regulator that reduces the internal CPU voltage. A flexible clock tree allows to select suitable operation frequencies
for peripheral resources independent of the CPU speed.
*1: These devices are under development and specification is preliminary. These products under development may
change its specification without notice.
Note: F2MC is the abbreviation of Fujitsu Flexible Microcontroller
For the information for microcontroller supports, see the following web site.
This web site includes the "Customer Design Review Supplement" which provides the latest cautions on
system development and the minimal requirements to be checked to prevent problems before the system
development.
http://edevice.fujitsu.com/micom/en-support/
Copyright©2010 FUJITSU SEMICONDUCTOR LIMITED All rights reserved
2010.6
MB96340 Series
■ FEATURES
Feature
Technology
Description
• 0.18µm CMOS
• F2MC-16FX CPU
• Up to 56 MHz internal, 17.8 ns instruction cycle time
CPU
• Optimized instruction set for controller applications (bit, byte, word and long-word
data types; 23 different addressing modes; barrel shift; variety of pointers)
• 8-byte instruction execution queue
• Signed multiply (16-bit × 16-bit) and divide (32-bit/16-bit) instructions available
• On-chip PLL clock multiplier (x1 - x25, x1 when PLL stop)
• 3 MHz - 16 MHz external crystal oscillator clock (maximum frequency when using
ceramic resonator depends on Q-factor).
• Up to 56 MHz external clock for devices with fast clock input feature
• 32-100 kHz subsystem quartz clock
System clock
• 100kHz/2MHz internal RC clock for quick and safe startup, oscillator stop detection,
watchdog
• Clock source selectable from main- and subclock oscillator (part number suffix “W”)
and on-chip RC oscillator, independently for CPU and 2 clock domains of peripherals.
• Low Power Consumption - 13 operating modes : (different Run, Sleep, Timer modes,
Stop mode)
• Clock modulator
On-chip voltage regula- • Internal voltage regulator supports reduced internal MCU voltage, offering low EMI
tor
and low power consumption figures
Low voltage reset
Code Security
Memory Patch Function
DMA
• Reset is generated when supply voltage is below minimum.
• Protects ROM content from unintended read-out
• Replaces ROM content
• Can also be used to implement embedded debug support
• Automatic transfer function independent of CPU, can be assigned freely to resources
• Fast Interrupt processing
Interrupts
• 8 programmable priority levels
• Non-Maskable Interrupt (NMI)
Timers
• Three independent clock timers (23-bit RC clock timer, 23-bit Main clock timer, 17-bit
Sub clock timer)
• Watchdog Timer
2
FME-MB96340 rev 10
MB96340 Series
Feature
Description
• Supports CAN protocol version 2.0 part A and B
• ISO16845 certified
• Bit rates up to 1 Mbit/s
• 32 message objects
CAN
• Each message object has its own identifier mask
• Programmable FIFO mode (concatenation of message objects)
• Maskable interrupt
• Disabled Automatic Retransmission mode for Time Triggered CAN applications
• Programmable loop-back mode for self-test operation
• Full duplex USARTs (SCI/LIN)
USART
• Wide range of baud rate settings using a dedicated reload timer
• Special synchronous options for adapting to different synchronous serial protocols
• LIN functionality working either as master or slave LIN device
I2C
• Up to 400 kbps
• Master and Slave functionality, 7-bit and 10-bit addressing
• SAR-type
A/D converter
• 10-bit resolution
• Signals interrupt on conversion end, single conversion mode, continuous conversion
mode, stop conversion mode, activation by software, external trigger or reload timer
A/D Converter Reference Voltage switch
• 2 independent positive A/D converter reference voltages available
• 16-bit wide
Reload Timers
• Prescaler with 1/21, 1/22, 1/23, 1/24, 1/25, 1/26 of peripheral clock frequency
• Event count function
Free Running Timers
• Signals an interrupt on overflow, supports timer clear upon match with Output
Compare (0, 4), Prescaler with 1, 1/21, 1/22, 1/23, 1/24, 1/25, 1/26, 1/27,1/28 of
peripheral clock frequency
• 16-bit wide
Input Capture Units
• Signals an interrupt upon external event
• Rising edge, falling edge or rising & falling edge sensitive
• 16-bit wide
Output Compare Units • Signals an interrupt when a match with 16-bit I/O Timer occurs
• A pair of compare registers can be used to generate an output signal.
FME-MB96340 rev 10
3
MB96340 Series
Feature
Description
• 16-bit down counter, cycle and duty setting registers
• Interrupt at trigger, counter borrow and/or duty match
Programmable Pulse
Generator
• PWM operation and one-shot operation
• Internal prescaler allows 1, 1/4, 1/16, 1/64 of peripheral clock as counter clock and
Reload timer underflow as clock input
• Can be triggered by software or reload timer
• Can be clocked either from sub oscillator (devices with part number suffix “W”), main
oscillator or from the RC oscillator
Real Time Clock
• Facility to correct oscillation deviation of Sub clock or RC oscillator clock (clock
calibration)
• Read/write accessible second/minute/hour registers
• Can signal interrupts every half second/second/minute/hour/day
• Internal clock divider and prescaler provide exact 1s clock
• Edge sensitive or level sensitive
External Interrupts
• Interrupt mask and pending bit per channel
• Each available CAN channel RX has an external interrupt for wake-up
• Selected USART channels SIN have an external interrupt for wake-up
• Disabled after reset
Non Maskable Interrupt
• Once enabled, can not be disabled other than by reset.
• Level high or level low sensitive
• Pin shared with external interrupt 0.
• 8-bit or 16-bit bidirectional data
• Up to 24-bit addresses
• 6 chip select signals
External bus interface
• Multiplexed address/data lines
• Wait state request
• External bus master possible
• Timing programmable
• Monitors an external voltage and generates an interrupt in case of a voltage lower or
higher than the defined thresholds
Alarm comparator
• Threshold voltages defined externally or generated internally
• Status is readable, interrupts can be masked separately
4
FME-MB96340 rev 10
MB96340 Series
Feature
Description
• Virtually all external pins can be used as general purpose I/O
• All push-pull outputs (except when used as I2C SDA/SCL line)
• Bit-wise programmable as input/output or peripheral signal
I/O Ports
• Bit-wise programmable input enable
• Bit-wise programmable input levels: Automotive / CMOS-Schmitt trigger / TTL (TTL
levels not supported by all devices)
• Bit-wise programmable pull-up resistor
• Bit-wise programmable output driving strength for EMI optimization
Packages
• 100-pin plastic QFP and LQFP
• Supports automatic programming, Embedded Algorithm
• Write/Erase/Erase-Suspend/Resume commands
• A flag indicating completion of the algorithm
• Number of erase cycles: 10,000 times
Flash Memory
• Data retention time: 20 years
• Erase can be performed on each sector individually
• Sector protection
• Flash Security feature to protect the content of the Flash
• Low voltage detection during Flash erase
FME-MB96340 rev 10
5
MB96340 Series
■ PRODUCT LINEUP
Features
MB96V300B
MB96(F)34x
Product type
Evaluation sample
Flash product: MB96F34x
Mask ROM product: MB9634x
Product options
YS
Low voltage reset persistently on / Single clock
RS
Low voltage reset can be disabled / Single clock
YW
Low voltage reset persistently on / Dual clock
RW
Low voltage reset can be disabled / Dual clock
TS
indep. 32KB Flash / Low voltage reset persistently on / Single clock
HS
indep. 32KB Flash / Low voltage reset can be disabled / Single clock
TW
indep. 32KB Flash / Low voltage reset persistently on / Dual clock
HW
indep. 32KB Flash / Low voltage reset can be disabled / Dual clock
FS
NA
64KB Data Flash / Low voltage reset persistently on / Single clock
DS
64KB Data Flash / Low voltage reset can be disabled / Single clock
FW
64KB Data Flash / Low voltage reset persistently on / Dual clock
DW
64KB Data Flash / Low voltage reset can be disabled / Dual clock
AS
No CAN / Low voltage reset can be disabled / Single clock devices
CS
No CAN / indep. 32KB Flash / Low voltage reset can be disabled /
Single clock
AW
No CAN / Low voltage reset can be disabled / Dual clock
CW
No CAN / indep. 32KB Flash / Low voltage reset can be disabled /
Dual clock
Flash/ROM
RAM
160KB
8KB
MB96345Y *1, MB96345R *1
224KB
[Flash A: 160KB,
Data Flash A: 64KB]
8KB
MB96F345F *1, MB96F345D *1
288KB
16KB
416KB
16KB
544KB
24KB
576KB
[Flash A: 544KB,
Flash B: 32KB]
24KB
Package
6
ROM/Flash
memory emulation
by external RAM,
92KB internal
RAM
MB96F346Y, MB96346Y *1, MB96F346R, MB96346R *1, MB96F346A
MB96F347Y, MB96F347R, MB96F347A
MB96F348Y, MB96F348R, MB96F348A
MB96F348T, MB96F348H, MB96F348C
BGA416
FPT-100P-M20
FPT-100P-M22
FME-MB96340 rev 10
MB96340 Series
Features
MB96V300B
MB96(F)34x
DMA
16 channels
6 channels
USART
10 channels
7 channels
I2C
2 channels
2 channels
A/D Converter
40 channels
24 channels
A/D Converter Reference
Voltage switch
yes
yes (except MB96F345Dyy or MB96F345Fyy)
16-bit Reload Timer
6 channels + 1
channel (for PPG)
4 channels + 1 channel (for PPG)
16-bit Free-Running Timer
4 channels
2 channels
16-bit Output Compare
12 channels
8 channels
16-bit Input Capture
12 channels
8 channels
16-bit Programmable Pulse
Generator
20 channels
16 channels
CAN Interface
5 channels
MB96(F)34xAyy or MB96(F)34xCyy: no
MB96F345Dyy or MB96F345Fyy: 1 channel
others: 2 channels
External Interrupts
16 channels
Non-Maskable Interrupt
1 channel
Real Time Clock
1
I/O Ports
Alarm comparator
External bus interface
136
80 for part number with suffix "W", 82 for part number with suffix "S"
2 channels
MB96F345Dyy or MB96F345Fyy: no
others: 2 channels
Yes
Yes (multiplexed address/data)
Chip select
6 signals
Clock output function
2 channels
Low voltage reset
Yes
On-chip RC-oscillator
Yes
*1: These devices are under development and specification is preliminary. These products under development may
change its specification without notice.
FME-MB96340 rev 10
7
MB96340 Series
■ BLOCK DIAGRAM
Block diagram of MB96(F)34x
AD00 ... AD15
A16 ... A23
ALE
RDX
WR(L)X, WRHX
HRQ
HAKX
NMI, NMI_R
RDY
ECLK
LBX, UBX
CS0 ... CS5
External Bus
Interface
16FX
CPU
Interrupt
Controller
CKOT0, CKOT1
CKOTX0, CKOTX1
X0, X1
X0A, X1A *1
RSTX
MD0...MD2
Flash
Memory A
Flash Memory B
or Data Flash A *2
Memory Patch
Unit
Clock &
Mode Controller
16FX Core Bus (CLKB)
SCL0, SCL1
AVCC
AVSS
AVRH
AVRL/AVRH2 *5
AN0 ... AN23
10-bit ADC
24 ch.
TOT0 ... TOT3
16-bit Reload
Timer
4 ch.
FRCK0
IN0 ... IN3
OUT0 ... OUT3
I/O Timer 0
ICU 0/1/2/3
OCU 0/1/2/3
FRCK1
IN4 ... IN7
OUT4 ... OUT7
I/O Timer 1
ICU 4/5/6/7
OCU 4/5/6/7
INT0 ... INT15
INT0_R ... INT2_R
INT4_R, INT5_R
INT7_R ... INT15_R
INT3_R1
Peripheral
Bus Bridge
I2C
2 ch.
ADTG, ADTG_R
TIN0 ... TIN3
Peripheral
Bus Bridge
Peripheral Bus 2 (CLKP2)
SDA0, SDA1
Watchdog
Peripheral Bus 1 (CLKP1)
DMA
Controller
USART
7 ch.
Alarm
Comparator
2 ch. *4
16-bit PPG
16 ch.
RLT6
External
Interrupt
Real Time
Clock
RAM
Boot ROM
Voltage
Regulator
VCC
VSS
C
CAN
Interface
2 ch.
TX0, TX1 *3
RX0, RX1 *3
SIN0...SIN3, SIN2_R, SIN7_R...SIN9_R
SOT0...SOT3, SOT2_R, SOT7_R...SOT9_R
SCK0...SCK3, SCK2_R, SCK7_R...SCK9_R
ALARM0 *4
ALARM1 *4
TTG0 ... TTG15
PPG0 ... PPG15
WOT
*1: X0A, X1A only available on MB96(F)34xyWy
*2: Flash B only available on MB96F34xCyy, MB96F34xHyy or MB96F34xTyy
Data Flash A only available on MB96F34xDyy or MB96F34xFyy
*3: CAN interfaces are not available on MB96(F)34xAyy or MB96(F)34xCyy
CAN1 is not available on MB96F345Dyy or MB96F345Fyy
*4: Alarm comparator is not available on MB96F345Dyy or MB96F345Fyy
*5: A/D converter reference voltage switch is not available on MB96F345Dyy or MB96F345Fyy
8
FME-MB96340 rev 10
MB96340 Series
■ PIN ASSIGNMENTS
MD2
MD1
MD0
RSTX
P07_6/AN22/INT6/SOT9_R
P07_7/AN23/INT7/SIN9_R
P08_0/TIN0/CKOTX0/ADTG/INT12_R
P08_1/TOT0/CKOT0/INT13_R
P08_2/SIN0/TIN2/INT14_R
P08_3/SOT0/TOT2
P08_4/SCK0/INT15_R
P08_5/SIN1/INT1_R
P08_6/SOT1
P08_7/SCK1
Vcc
Vss
P09_0/PPG8/UBX
P09_1/PPG9/LBX
P09_2/PPG10/CS5
P09_3/PPG11/CS4
P09_4/OUT0/CS3
P09_5/OUT1/CS2
P09_6/OUT2/CS1
P09_7/OUT3/CS0
P10_0/RX0/INT8_R *2
P10_1/TX0 *2
P00_0/AD00/INT8/SCK7_R
P00_1/AD01/INT9/SOT7_R
P00_2/AD02/INT10/SIN7_R
P00_3/AD03/INT11/SCK8_R
Pin assignment of MB96(F)34x (FPT-100P-M22)
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
P00_4/AD04/INT12/SOT8_R
81
50
P07_5/AN21/INT5/SCK9_R
P00_5/AD05/INT13/SIN8_R
82
49
P07_4/AN20/INT4
P00_6/AD06/INT14
83
48
P07_3/AN19/INT3
P00_7/AD07/INT15
84
47
P07_2/AN18/INT2
P01_0/AD08/CKOT1/TIN1
85
46
P07_1/AN17/INT1
P01_1/AD09/CKOTX1/TOT1
86
45
P07_0/AN16/INT0/NMI
P01_2/AD10/INT11_R/SIN3
87
44
Vss
P01_3/AD11/SOT3
88
43
P06_7/AN7/PPG7
P01_4/AD12/SCK3
89
42
P06_6/AN6/PPG6
Vcc
90
41
P06_5/AN5/PPG5
Vss
91
40
P06_4/AN4/PPG4
X1
92
39
P06_3/AN3/PPG3
X0
93
38
P06_2/AN2/PPG2
P01_5/AD13/INT7_R/SIN2_R
94
37
P06_1/AN1/PPG1
P01_6/AD14/SOT2_R
95
36
P06_0/AN0/PPG0
P01_7/AD15/SCK2_R
96
35
AVss
P02_0/A16/PPG12
97
34
AVRL/AVRH2 *4
P02_1/A17/PPG13
98
33
AVRH
P02_2/A18/PPG14
99
32
P02_3/A19/PPG15
100
31
AVcc
P05_7/AN15/INT5_R
QFP - 100
P05_6/AN14/INT4_R
P05_5/AN13/INT0_R/NMI_R
P05_4/AN12/TOT3/INT2_R
P05_3/AN11/TIN3/WOT
P05_2/AN10/SCK2
P05_1/AN9/ALARM1/SOT2 *3
P05_0/AN8/ALARM0/SIN2/INT3_R1 *3
P04_7/SCL1
P04_6/SDA1
P04_5/SCL0/FRCK1
P04_4/SDA0/FRCK0
P04_3/IN7/TX1/TTG7/TTG15 *2
P04_2/IN6/RX1/INT9_R/TTG6/TTG14 *2
C
X1A/P04_1
Vss
*1
X0A/P04_0
Vcc
*1
P03_7/ECLK/OUT7
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
P03_6/RDY/OUT6
8
P03_5/HAKX/OUT5
7
P03_4/HRQ/OUT4
6
P03_3/WRHX
P02_6/A22/IN2/TTG2/TTG10
5
P03_2/WRLX/WRX/INT10_R
P02_4/A20/TTG8/TTG0/IN0
4
P03_1/RDX/IN5/TTG5/TTG13
3
P02_7/A23/IN3/TTG3/TTG11
2
P03_0/ALE/IN4/TTG4/TTG12
1
P02_5/A21/TTG9/TTG1/IN1/ADTG_R
Package code (mold)
FPT-100P-M22
*1: MB96(F)34xyWy: X0A, X1A
MB96(F)34xySy: P04_0, P04_1
*2: TX0, RX0, TX1, RX1 are not available on MB96(F)34xAyy or MB96(F)34xCyy
TX1, RX1 are not available on MB96F345Dyy or MB96F345Fyy
*3: ALARM0, ALARM1 are not available on MB96F345Dyy or MB96F345Fyy
*4: AVRH2 is not available on MB96F345Dyy or MB96F345Fyy
(FPT-100P-M22)
Remark:
MB96(F)34x products are pin-compatible to F2MC-16LX family MB90340 series.
FME-MB96340 rev 10
9
MB96340 Series
MD0
RSTX
P07_6/AN22/INT6/SOT9_R
P07_7/AN23/INT7/SIN9_R
P08_0/TIN0/CKOTX0/ADTG/INT12_R
P08_1/TOT0/CKOT0/INT13_R
P08_2/SIN0/TIN2/INT14_R
P08_3/SOT0/TOT2
P08_4/SCK0/INT15_R
P08_5/SIN1/INT1_R
P08_6/SOT1
P08_7/SCK1
Vcc
Vss
P09_0/PPG8/UBX
P09_1/PPG9/LBX
P09_2/PPG10/CS5
P09_3/PPG11/CS4
P09_4/OUT0/CS3
P09_5/OUT1/CS2
P09_6/OUT2/CS1
*2
P09_7/OUT3/CS0
*2
P10_0/RX0/INT8_R
P10_1/TX0
P00_0/AD00/INT8/SCK7_R
Pin assignment of MB96(F)34x (FPT-100P-M20)
P00_1AD01/INT9/SOT7_R
76
75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
50
MD1
P00_2/AD02/INT10/SIN7_R
77
49
MD2
P00_3/AD03/INT11/SCK8_R
78
48
P07_5/AN21/INT5/SCK9_R
P00_4/AD04/INT12/SOT8_R
79
47
P07_4/AN20/INT4
P00_5/AD05/INT13/SIN8_R
80
46
P07_3/AN19/INT3
P00_6/AD06/INT14
81
45
P07_2/AN18/INT2
P00_7/AD07/INT15
82
44
P07_1/AN17/INT1
P01_0/AD08/CKOT1/TIN1
83
43
P07_0/AN16/INT0/NMI
P01_1/AD09/CKOTX1/TOT1
84
42
Vss
P01_2/AD10/INT11_R/SIN3
85
41
P06_7/AN7/PPG7
P01_3/AD11/SOT3
86
40
P06_6/AN6/PPG6
P01_4/AD12/SCK3
87
39
P06_5/AN5/PPG5
Vcc
88
38
P06_4/AN4/PPG4
Vss
89
37
P06_3/AN3/PPG3
X1
90
36
P06_2/AN2/PPG2
X0
91
35
P06_1/AN1/PPG1
P01_5/AD13/INT7_R/SIN2_R
92
34
P06_0/AN0/PPG0
P01_6/AD14/SOT2_R
93
33
AVss
P01_7/AD15/SCK2_R
94
32
AVRL/AVRH2 *4
P02_0/A16/PPG12
95
31
AVRH
P02_1/A17/PPG13
96
30
AVcc
P02_2/A18/PPG14
97
29
P05_7/AN15/INT5_R
P02_3/A19/PPG15
98
28
P05_6/AN14/INT4_R
P02_4/A20/TTG8/TTG0/IN0
99
27
P05_5/AN13/INT0_R/NMI_R
Package code (mold)
FPT-100P-M20
P05_4/AN12/TOT3/INT2_R
P05_3/AN11/TIN3/WOT
P05_2/AN10/SCK2
P05_1/AN9/ALARM1/SOT2 *3
P05_0/AN8/ALARM0/SIN2/INT3_R1 *3
P04_7/SCL1
P04_6/SDA1
P04_5/SCL0/FRCK1
P04_4/SDA0/FRCK0
P04_3/IN7/TX1/TTG7/TTG15 *2
P04_2/IN6/RX1/INT9_R/TTG6/TTG14 *2
C
Vss
Vcc
*1
P03_4/HRQ/OUT4
X1A/P04_1
7 8
X0A/P04_0 *1
6
P03_7/ECLK/OUT7
5
P03_6/RDY/OUT6
4
P03_3/WRHX
2
26
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
P03_5/HAKX/OUT5
3
P03_2/WRLX/WRX/INT10_R
P02_6/A22/IN2/TTG2/TTG10
1
P03_1/RDX/IN5/TTG5/TTG13
100
P02_7/A23/IN3/TTG3/TTG11
P03_0/ALE/IN4/TTG4/TTG12
P02_5/A21/TTG9/TTG1/IN1/ADTG_R
LQFP - 100
*1: MB96(F)34xyWy: X0A, X1A
MB96(F)34xySy: P04_0, P04_1
*2: TX0, RX0, TX1, RX1 are not available on MB96(F)34xAyy or MB96(F)34xCyy
TX1, RX1 are not available on MB96F345Dyy or MB96F345Fyy
*3: ALARM0, ALARM1 are not available on MB96F345Dyy or MB96F345Fyy
*4: AVRH2 is not available on MB96F345Dyy or MB96F345Fyy
(FPT-100P-M20)
Remark:
MB96(F)34x products are pin-compatible to F2MC-16LX family MB90340 series.
10
FME-MB96340 rev 10
MB96340 Series
■ PIN FUNCTION DESCRIPTION
Pin Function description (1 of 2)
Pin name
Feature
Description
ADn
External bus
External bus interface (multiplexed mode) address output and
data input/output
ADTG
ADC
A/D converter trigger input
ADTG_R
ADC
Relocated A/D converter trigger input
ALARMn
Alarm comparator
Alarm Comparator n input
ALE
External bus
External bus Address Latch Enable output
An
External bus
External bus address output
ANn
ADC
A/D converter channel n input
AVCC
Supply
Analog circuits power supply
AVRH
ADC
A/D converter high reference voltage input
AVRH2
ADC
Alternative A/D converter high reference voltage input
AVRL
ADC
A/D converter low reference voltage input
AVSS
Supply
Analog circuits power supply
C
Voltage regulator
Internally regulated power supply stabilization capacitor pin
CKOTn
Clock output function
Clock Output function n output
CKOTXn
Clock output function
Clock Output function n inverted output
ECLK
External bus
External bus clock output
CSn
External bus
External bus chip select n output
FRCKn
Free Running Timer
Free Running Timer n input
HAKX
External bus
External bus Hold Acknowledge
HRQ
External bus
External bus Hold Request
INn
ICU
Input Capture Unit n input
INTn
External Interrupt
External Interrupt n input
INTn_R
External Interrupt
Relocated External Interrupt n input
LBX
External bus
External Bus Interface Lower Byte select strobe output
MDn
Core
Input pins for specifying the operating mode.
NMI
External Interrupt
Non-Maskable Interrupt input
NMI_R
External Interrupt
Relocated Non-Maskable Interrupt input
OUTn
OCU
Output Compare Unit n waveform output
FME-MB96340 rev 10
11
MB96340 Series
Pin Function description (2 of 2)
Pin name
Feature
Description
Pxx_n
GPIO
General purpose IO
PPGn
PPG
Programmable Pulse Generator n output
RDX
External bus
External bus interface read strobe output
RDY
External bus
External bus interface external wait state request input
RSTX
Core
Reset input
RXn
CAN
CAN interface n RX input
SCKn
USART
USART n serial clock input/output
SCKn_R
USART
Relocated USART n serial clock input/output
SCLn
I2C
I2C interface n clock I/O input/output
SDAn
I2C
I2C interface n serial data I/O input/output
SINn
USART
USART n serial data input
SINn_R
USART
Relocated USART n serial data input
SOTn
USART
USART n serial data output
SOTn_R
USART
Relocated USART n serial data output
TINn
Reload Timer
Reload Timer n event input
TOTn
Reload Timer
Reload Timer n output
TTGn
PPG
Programmable Pulse Generator n trigger input
TXn
CAN
CAN interface n TX output
UBX
External bus
External Bus Interface Upper Byte select strobe output
VCC
Supply
Power supply
VSS
Supply
Power supply
WOT
RTC
Real Timer clock output
WRHX
External bus
External bus High byte write strobe output
WRLX/WRX
External bus
External bus Low byte / Word write strobe output
X0
Clock
Oscillator input
X0A
Clock
Subclock Oscillator input (only for devices with suffix "W")
X1
Clock
Oscillator output
X1A
Clock
Subclock Oscillator output (only for devices with suffix "W")
12
FME-MB96340 rev 10
MB96340 Series
■ PIN CIRCUIT TYPE
Pin circuit types
FPT-100P-M20
FPT-100P-M22
Pin no.
Circuit
type *1
Pin no.
Circuit
type *1
1-10
H
1-12
H
11,12
B *2
13, 14
B *2
11,12
H *3
13, 14
H *3
13,14
Supply
15,16
Supply
15
F
17
F
16,17
H
18,19
H
18-21
N
20-23
N
22-29
I
24-31
I
30
Supply
32
Supply
31-32
G
33-34
G
33
Supply
35
Supply
34 to 41
I
36 to 43
I
42
Supply
44
Supply
43 to 48
I
45 to 50
I
49 to 51
C
51 to 53
C
52
E
54
E
53 to 54
I
55 to 56
I
55 to 62
H
57 to 64
H
63, 64
Supply
65, 66
Supply
65 to 87
H
67 to 89
H
88,89
Supply
90, 91
Supply
90, 91
A
92, 93
A
92-100
H
94 to 100
H
*1: Please refer to “■ I/O CIRCUIT TYPE” for details on the I/O circuit types
*2: Devices with suffix ”W”
*3: Devices without suffix ”W”
FME-MB96340 rev 10
13
MB96340 Series
■ I/O CIRCUIT TYPE
Type
Circuit
Remarks
A
X1
R
0
Xout
MRFBE
1
High-speed oscillation circuit:
• Programmable between oscillation mode (external crystal or resonator connected to X0/X1
pins) and Fast external Clock Input (FCI) mode
(external clock connected to X0 pin)
• Programmable feedback resistor = approx.
2 * 0.5 MΩ. Feedback resistor is grounded in
the center when the oscillator is disabled or in
FCI mode
FCI
R
X0
FCI or osc disable
B
Xout
X1A
Low-speed oscillation circuit:
• Programmable feedback resistor = approx.
2 * 5 MΩ. Feedback resistor is grounded in the
center when the oscillator is disabled
R
SRFBE
R
X0A
osc disable
C
R
Hysteresis
inputs
E
• Mask ROM and EVA device:
CMOS Hysteresis input pin
• Flash device:
CMOS input pin
• CMOS Hysteresis input pin
• Pull-up resistor value: approx. 50 kΩ
Pull-up
Resistor
R
14
Hysteresis
inputs
FME-MB96340 rev 10
MB96340 Series
Type
Circuit
Remarks
F
• Power supply input protection circuit
G
• A/D converter ref+ (AVRH/AVRH2) power supply input pin with protection circuit
• Flash devices do not have a protection circuit
against VCC for pins AVRH/AVRH2
• Devices without AVRH reference switch do not
have an analog switch for the AVRL pin
ANE
AVR
ANE
H
pull-up control
Pout
Nout
R
Standby control
for input shutdown
Hysteresis input
Standby control
for input shutdown
Hysteresis input
Standby control
for input shutdown
Automotive input
Standby control
for input shutdown
TTL input
FME-MB96340 rev 10
• CMOS level output (programmable IOL = 5mA,
IOH = -5mA and IOL = 2mA, IOH = -2mA)
• 2 different CMOS hysteresis inputs with input
shutdown function *
• Automotive input with input shutdown function
• TTL input with input shutdown function *
• Programmable pull-up resistor: 50kΩ approx.
Note: MB96F345Dyy or MB96F345Fyy:
Only Automotive input and CMOS hysteresis input (0.7/0.3) are supported
15
MB96340 Series
Type
Circuit
Remarks
I
Pull-up control
Pout
Nout
• CMOS level output (programmable IOL = 5mA,
IOH = -5mA and IOL = 2mA, IOH = -2mA)
• 2 different CMOS hysteresis inputs with input
shutdown function *
• Automotive input with input shutdown function
• TTL input with input shutdown function *
• Programmable pull-up resistor: 50kΩ approx.
• Analog input
R
Hysteresis input
Standby control
for input shutdown
Standby control
for input shutdown
Hysteresis input
Standby control
for input shutdown
Automotive input
Standby control
for input shutdown
TTL input
Note: MB96F345Dyy or MB96F345Fyy:
Only Automotive input and CMOS hysteresis input (0.7/0.3) are supported
Analog input
N
pull-up control
Pout
• CMOS level output (IOL = 3mA, IOH = -3mA)
• 2 different CMOS hysteresis inputs with input
shutdown function *
• Automotive input with input shutdown function
• TTL input with input shutdown function *
• Programmable pull-up resistor: 50kΩ approx.
Nout *1
*1: N-channel transistor has slew rate control according to I2C spec, irrespective of usage
R
16
Standby control
for input shutdown
Hysteresis input
Standby control
for input shutdown
Hysteresis input
Standby control
for input shutdown
Automotive input
Standby control
for input shutdown
TTL input
Note: MB96F345Dyy or MB96F345Fyy:
Only Automotive input and CMOS hysteresis input (0.7/0.3) are supported
FME-MB96340 rev 10
MB96340 Series
■ MEMORY MAP
MB96V300B
MB96(F)34x
Emulation ROM
USER ROM /
External Bus*4
External Bus
External Bus
Boot-ROM
Boot-ROM
FF:FFFFH
DE:0000H
10:0000H
0F:E000H
0F:0000H
Reserved
Reserved
DATA FLASH /
Reserved*4
0E:0000H
0C:0000H
External RAM
Reserved
02:0000H
Internal RAM
bank 1
RAMEND1*2
RAMSTART12
01:0000H
ROM/RAM MIRROR
Reserved
Internal RAM
bank 1
Reserved
RAM availability depending on the device
ROM/RAM MIRROR
00:8000H
Internal RAM
bank 0
RAMSTART0*2
Reserved
External Bus end
address*2
External Bus
RAMSTART0*3
00:0C00H
Internal RAM
bank 0
External Bus
Peripherals
Peripherals
GPR*1
GPR*1
DMA
DMA
External Bus
External Bus
Peripheral
Peripheral
00:0380H
00:0180H
00:0100H
00:00F0H
00:0000H
*1: Unused GPR banks can be used as RAM area
*2: For External Bus end address and RAMSTART/END addresses, please refer to the table on the next page.
*3: For EVA device, RAMSTART0 depends on the configuration of the emulated device.
*4: For details about USER ROM area or DATA FLASH area, see the ■ USER ROM MEMORY MAP FOR
FLASH DEVICES and ■ USER ROM MEMORY MAP FOR MASK ROM DEVICES on the following pages.
The External Bus area and DMA area are only available if the device contains the corresponding resource.
The available RAM and ROM area depends on the device.
FME-MB96340 rev 10
17
MB96340 Series
■ RAMSTART/END AND EXTERNAL BUS END ADDRESSES
Devices
18
Bank 0
Bank 1 External Bus
RAM size RAM size end address
RAMSTART0
RAMSTART1 RAMEND1
MB96(F)345
8KByte
-
00:21FFH
00:6240H
-
-
MB96(F)346,
MB96F347
16KByte
-
00:21FFH
00:4240H
-
-
MB96F348
24KByte
-
00:21FFH
00:2240H
-
-
FME-MB96340 rev 10
MB96340 Series
■ USER ROM MEMORY MAP FOR FLASH DEVICES
MB96F345D
MB96F345F
Alternative mode
CPU address
Flash memory
mode address
FF:FFFFH
FF:0000H
FE:FFFFH
FE:0000H
FD:FFFFH
FD:0000H
FC:FFFFH
FC:0000H
FB:FFFFH
FB:0000H
FA:FFFFH
FA:0000H
F9:FFFFH
F9:0000H
F8:FFFFH
F8:0000H
F7:FFFFH
F7:0000H
F6:FFFFH
F6:0000H
F5:FFFFH
F5:0000H
F4:FFFFH
F4:0000H
F3:FFFFH
F3:0000H
F2:FFFFH
F2:0000H
F1:FFFFH
F1:0000H
F0:FFFFH
F0:0000H
E0:FFFFH
3F:FFFFH
3F:0000H
3E:FFFFH
3E:0000H
3D:FFFFH
3D:0000H
3C:FFFFH
3C:0000H
3B:FFFFH
3B:0000H
3A:FFFFH
3A:0000H
39:FFFFH
39:0000H
38:FFFFH
38:0000H
37:FFFFH
37:0000H
36:FFFFH
36:0000H
35:FFFFH
35:0000H
34:FFFFH
34:0000H
33:FFFFH
33:0000H
32:FFFFH
32:0000H
31:FFFFH
31:0000H
30:FFFFH
30:0000H
E0:0000H
DF:FFFFH
DF:8000H
DF:7FFFH
DF:6000H
DF:5FFFH
DF:4000H
DF:3FFFH
DF:2000H
DF:1FFFH
DF:0000H
DE:FFFFH
Flash size 160kByte
+64KByte Data Flash
S39 - 64K
S38 - 64K
Flash A
External bus
Reserved
1F:7FFFH
1F:6000H
1F:5FFFH
1F:4000H
1F:3FFFH
1F:2000H
1F:1FFFH
1F:0000H
SA3 - 8K
SA2 - 8K
SA1 - 8K
SA0 - 8K *1
Flash A
Reserved
DE:0000H
0E:FFFFH
0E:FF00H
0E:FEFFH
0E:0000H
0D:FFFFH
0D:C000H
0D:BFFFH
0D:8000H
0D:7FFFH
0D:4000H
0D:3FFFH
0D:0000H
0C:FFFFH
0C:0000H
(0E:FFFFH)
(0E:FF00H)
(0F:FFFFH)
(0F:C000H)
(0F:BFFFH)
(0F:8000H)
(0F:7FFFH)
(0F:4000H)
(0F:3FFFH)
(0F:0000H)
SDA0-256 *2
Reserved
SDA4-16K
SDA3-16K
SDA2-16K
SDA1-16K
Reserved
Data Flash A
Data Flash A
*1: Sector SA0 contains the ROM Configuration Block RCBA at CPU address DF:0000H - DF:007FH
*2: Sector SDA0 contains the ROM Configuration Block RCBDA at CPU address DE:FF00H - DE:FF2FH
FME-MB96340 rev 10
19
MB96340 Series
Alternative mode
CPU address
Flash memory
mode address
FF:FFFFH
FF:0000H
FE:FFFFH
FE:0000H
FD:FFFFH
FD:0000H
FC:FFFFH
FC:0000H
FB:FFFFH
FB:0000H
FA:FFFFH
FA:0000H
F9:FFFFH
F9:0000H
F8:FFFFH
F8:0000H
F7:FFFFH
F7:0000H
F6:FFFFH
F6:0000H
F5:FFFFH
F5:0000H
F4:FFFFH
F4:0000H
F3:FFFFH
F3:0000H
F2:FFFFH
F2:0000H
F1:FFFFH
F1:0000H
F0:FFFFH
F0:0000H
E0:FFFFH
3F:FFFFH
3F:0000H
3E:FFFFH
3E:0000H
3D:FFFFH
3D:0000H
3C:FFFFH
3C:0000H
3B:FFFFH
3B:0000H
3A:FFFFH
3A:0000H
39:FFFFH
39:0000H
38:FFFFH
38:0000H
37:FFFFH
37:0000H
36:FFFFH
36:0000H
35:FFFFH
35:0000H
34:FFFFH
34:0000H
33:FFFFH
33:0000H
32:FFFFH
32:0000H
31:FFFFH
31:0000H
30:FFFFH
30:0000H
E0:0000H
DF:FFFFH
DF:8000H
DF:7FFFH
DF:6000H
DF:5FFFH
DF:4000H
DF:3FFFH
DF:2000H
DF:1FFFH
DF:0000H
DE:FFFFH
1F:7FFFH
1F:6000H
1F:5FFFH
1F:4000H
1F:3FFFH
1F:2000H
1F:1FFFH
1F:0000H
MB96F346Y
MB96F346R
MB96F346A
MB96F347Y
MB96F347R
MB96F347A
Flash size
288kByte
Flash size
416kByte
S39 - 64K
S38 - 64K
S37 - 64K
S36 - 64K
S39 - 64K
S38 - 64K
S37 - 64K
S36 - 64K
S35 - 64K
S34 - 64K
Flash A
External bus
External bus
Reserved
Reserved
SA3 - 8K
SA2 - 8K
SA1 - 8K
SA0 - 8K *1
SA3 - 8K
SA2 - 8K
SA1 - 8K
SA0 - 8K *1
Reserved
Reserved
Flash A
DE:0000H
*1: Sector SA0 contains the ROM Configuration Block RCBA at CPU address DF:0000H - DF:007FH
20
FME-MB96340 rev 10
MB96340 Series
Alternative mode
CPU address
Flash memory
mode address
FF:FFFFH
FF:0000H
FE:FFFFH
FE:0000H
FD:FFFFH
FD:0000H
FC:FFFFH
FC:0000H
FB:FFFFH
FB:0000H
FA:FFFFH
FA:0000H
F9:FFFFH
F9:0000H
F8:FFFFH
F8:0000H
F7:FFFFH
F7:0000H
F6:FFFFH
F6:0000H
F5:FFFFH
F5:0000H
F4:FFFFH
F4:0000H
F3:FFFFH
F3:0000H
F2:FFFFH
F2:0000H
F1:FFFFH
F1:0000H
F0:FFFFH
F0:0000H
E0:FFFFH
3F:FFFFH
3F:0000H
3E:FFFFH
3E:0000H
3D:FFFFH
3D:0000H
3C:FFFFH
3C:0000H
3B:FFFFH
3B:0000H
3A:FFFFH
3A:0000H
39:FFFFH
39:0000H
38:FFFFH
38:0000H
37:FFFFH
37:0000H
36:FFFFH
36:0000H
35:FFFFH
35:0000H
34:FFFFH
34:0000H
33:FFFFH
33:0000H
32:FFFFH
32:0000H
31:FFFFH
31:0000H
30:FFFFH
30:0000H
E0:0000H
DF:FFFFH
DF:8000H
DF:7FFFH
DF:6000H
DF:5FFFH
DF:4000H
DF:3FFFH
DF:2000H
DF:1FFFH
DF:0000H
DE:FFFFH
DE:8000H
DE:7FFFH
DE:6000H
DE:5FFFH
DE:4000H
DE:3FFFH
DE:2000H
DE:1FFFH
DE:0000H
1F:7FFFH
1F:6000H
1F:5FFFH
1F:4000H
1F:3FFFH
1F:2000H
1F:1FFFH
1F:0000H
MB96F348Y
MB96F348R
MB96F348A
MB96F348T
MB96F348H
MB96F348C
Flash size
544kByte
Flash size
576kByte
S39 - 64K
S38 - 64K
S37 - 64K
S36 - 64K
S35 - 64K
S34 - 64K
S33 - 64K
S32 - 64K
S39 - 64K
S38 - 64K
S37 - 64K
S36 - 64K
S35 - 64K
S34 - 64K
S33 - 64K
S32 - 64K
External bus
External bus
Reserved
Reserved
SA3 - 8K
SA2 - 8K
SA1 - 8K
SA0 - 8K *1
SA3 - 8K
SA2 - 8K
SA1 - 8K
SA0 - 8K *1
Flash A
Flash A
Reserved
1E:7FFFH
1E:6000H
1E:5FFFH
1E:4000H
1E:3FFFH
1E:2000H
1E:1FFFH
1E:0000H
Reserved
SB3 - 8K
SB2 - 8K
SB1 - 8K
SB0 - 8K *2
Flash B
*1: Sector SA0 contains the ROM Configuration Block RCBA at CPU address DF:0000H - DF:007FH
*2: Sector SB0 contains the ROM Configuration Block RCBB at CPU address DE:0000H - DE:002FH
FME-MB96340 rev 10
21
MB96340 Series
■ USER ROM MEMORY MAP FOR MASK ROM DEVICES
CPU address
MB96345
MB96346
ROM size
160kByte
ROM size
288kByte
FF:FFFFH
FF:0000H
FE:FFFFH
128K ROM
FE:0000H
FD:FFFFH
FD:0000H
FC:FFFFH
256K ROM
Reserved
FC:0000H
FB:FFFFH
E0:0000H
DF:FFFFH
External bus
External bus
Reserved
Reserved
32K ROM
32K ROM
ROM configuration
block RCB
ROM configuration
block RCB
Reserved
Reserved
DF:8000H
DF:7FFFH
DF:0080H
DF:007FH
DF:0000H
DE:FFFFH
DE:0000H
22
FME-MB96340 rev 10
MB96340 Series
■ SERIAL PROGRAMMING COMMUNICATION INTERFACE
USART pins for Flash serial programming (MD[2:0] = 010, Serial Communication mode)
MB96F34x
Pin number
Pin number
USART Number
Normal function
LQFP-100
QFP-100
57
59
58
60
59
61
SCK0
60
62
SIN1
61
63
62
64
SCK1
22
24
SIN2
23
25
24
26
SCK2
85
87
SIN3
86
88
87
89
SIN0
USART0
USART1
USART2
USART3
SOT0
SOT1
SOT2
SOT3
SCK3
Note: If a Flash programmer and its software needs to use a handshaking pin, Fujitsu suggests to the tool vendor
to support at least port P00_1 on pin 76/78.
If handshaking is used by the tool but P00_1 is not available in customer’s application, Fujitsu suggests to the
customer to check the tool manual or to contact the tool vendor for alternative handshaking pins.
FME-MB96340 rev 10
23
MB96340 Series
■ I/O MAP
I/O map MB96(F)34x (1 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
000000H
I/O Port P00 - Port Data Register
PDR00
R/W
000001H
I/O Port P01 - Port Data Register
PDR01
R/W
000002H
I/O Port P02 - Port Data Register
PDR02
R/W
000003H
I/O Port P03 - Port Data Register
PDR03
R/W
000004H
I/O Port P04 - Port Data Register
PDR04
R/W
000005H
I/O Port P05 - Port Data Register
PDR05
R/W
000006H
I/O Port P06 - Port Data Register
PDR06
R/W
000007H
I/O Port P07 - Port Data Register
PDR07
R/W
000008H
I/O Port P08 - Port Data Register
PDR08
R/W
000009H
I/O Port P09 - Port Data Register
PDR09
R/W
00000AH
I/O Port P10 - Port Data Register
PDR10
R/W
00000BH000017H
Reserved
000018H
ADC0 - Control Status register Low
ADCSL
000019H
ADC0 - Control Status register High
ADCSH
00001AH
ADC0 - Data Register Low
ADCRL
00001BH
ADC0 - Data Register High
ADCRH
00001CH
ADC0 - Setting Register
00001DH
ADC0 - Setting Register
00001EH
ADC0 - Extended Configuration Register
00001FH
Reserved
000020H
FRT0 - Data register of free-running timer
000021H
FRT0 - Data register of free-running timer
000022H
FRT0 - Control status register of free-running timer
Low
TCCSL0
000023H
FRT0 - Control status register of free-running timer
High
TCCSH0
000024H
FRT1 - Data register of free-running timer
000025H
FRT1 - Data register of free-running timer
24
ADCS
R/W
R/W
ADCR
R
R
ADSR
R/W
R/W
ADECR
R/W
TCDT0
R/W
R/W
TCCS0
R/W
R/W
TCDT1
R/W
R/W
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (2 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
000026H
FRT1 - Control status register of free-running timer
Low
TCCSL1
TCCS1
R/W
000027H
FRT1 - Control status register of free-running timer
High
TCCSH1
R/W
000028H
OCU0 - Output Compare Control Status
OCS0
R/W
000029H
OCU1 - Output Compare Control Status
OCS1
R/W
00002AH
OCU0 - Compare Register
00002BH
OCU0 - Compare Register
00002CH
OCU1 - Compare Register
00002DH
OCU1 - Compare Register
00002EH
OCU2 - Output Compare Control Status
OCS2
R/W
00002FH
OCU3 - Output Compare Control Status
OCS3
R/W
000030H
OCU2 - Compare Register
000031H
OCU2 - Compare Register
000032H
OCU3 - Compare Register
000033H
OCU3 - Compare Register
000034H
OCU4 - Output Compare Control Status
OCS4
R/W
000035H
OCU5 - Output Compare Control Status
OCS5
R/W
000036H
OCU4 - Compare Register
000037H
OCU4 - Compare Register
000038H
OCU5 - Compare Register
000039H
OCU5 - Compare Register
00003AH
OCU6 - Output Compare Control Status
OCS6
R/W
00003BH
OCU7 - Output Compare Control Status
OCS7
R/W
00003CH
OCU6 - Compare Register
00003DH
OCU6 - Compare Register
00003EH
OCU7 - Compare Register
00003FH
OCU7 - Compare Register
000040H
ICU0/ICU1 - Control Status Register
ICS01
R/W
000041H
ICU0/ICU1 - Edge register
ICE01
R/W
000042H
ICU0 - Capture Register Low
FME-MB96340 rev 10
OCCP0
R/W
R/W
OCCP1
R/W
R/W
OCCP2
R/W
R/W
OCCP3
R/W
R/W
OCCP4
R/W
R/W
OCCP5
R/W
R/W
OCCP6
R/W
R/W
OCCP7
R/W
R/W
IPCPL0
IPCP0
R
25
MB96340 Series
I/O map MB96(F)34x (3 of 30)
Abbreviation
8-bit access
Abbreviation
16-bit access
Address
Register
000043H
ICU0 - Capture Register High
IPCPH0
000044H
ICU1 - Capture Register Low
IPCPL1
000045H
ICU1 - Capture Register High
IPCPH1
R
000046H
ICU2/ICU3 - Control Status Register
ICS23
R/W
000047H
ICU2/ICU3 - Edge register
ICE23
R/W
000048H
ICU2 - Capture Register Low
IPCPL2
000049H
ICU2 - Capture Register High
IPCPH2
00004AH
ICU3 - Capture Register Low
IPCPL3
00004BH
ICU3 - Capture Register High
IPCPH3
R
00004CH
ICU4/ICU5 - Control Status Register
ICS45
R/W
00004DH
ICU4/ICU5 - Edge register
ICE45
R/W
00004EH
ICU4 - Capture Register Low
IPCPL4
00004FH
ICU4 - Capture Register High
IPCPH4
000050H
ICU5 - Capture Register Low
IPCPL5
000051H
ICU5 - Capture Register High
IPCPH5
R
000052H
ICU6/ICU7 - Control Status Register
ICS67
R/W
000053H
ICU6/ICU7 - Edge register
ICE67
R/W
000054H
ICU6 - Capture Register Low
IPCPL6
000055H
ICU6 - Capture Register High
IPCPH6
000056H
ICU7 - Capture Register Low
IPCPL7
000057H
ICU7 - Capture Register High
IPCPH7
R
000058H
EXTINT0 - External Interrupt Enable Register
ENIR0
R/W
000059H
EXTINT0 - External Interrupt Interrupt request
Register
EIRR0
R/W
00005AH
EXTINT0 - External Interrupt Level Select Low
ELVRL0
00005BH
EXTINT0 - External Interrupt Level Select High
ELVRH0
R/W
00005CH
EXTINT1 - External Interrupt Enable Register
ENIR1
R/W
00005DH
EXTINT1 - External Interrupt Interrupt request
Register
EIRR1
R/W
00005EH
EXTINT1 - External Interrupt Level Select Low
ELVRL1
00005FH
EXTINT1 - External Interrupt Level Select High
ELVRH1
26
Access
R
IPCP1
IPCP2
R
R
R
IPCP3
IPCP4
R
R
R
IPCP5
IPCP6
R
R
R
IPCP7
ELVR0
ELVR1
R
R/W
R/W
R/W
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (4 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
TMCSR0
R/W
000060H
RLT0 - Timer Control Status Register Low
TMCSRL0
000061H
RLT0 - Timer Control Status Register High
TMCSRH0
000062H
RLT0 - Reload Register - for writing
TMRLR0
W
000062H
RLT0 - Reload Register - for reading
TMR0
R
000063H
RLT0 - Reload Register - for writing
W
000063H
RLT0 - Reload Register - for reading
R
000064H
RLT1 - Timer Control Status Register Low
TMCSRL1
000065H
RLT1 - Timer Control Status Register High
TMCSRH1
000066H
RLT1 - Reload Register - for writing
TMRLR1
W
000066H
RLT1 - Reload Register - for reading
TMR1
R
000067H
RLT1 - Reload Register - for writing
W
000067H
RLT1 - Reload Register - for reading
R
000068H
RLT2 - Timer Control Status Register Low
TMCSRL2
000069H
RLT2 - Timer Control Status Register High
TMCSRH2
00006AH
RLT2 - Reload Register - for writing
TMRLR2
W
00006AH
RLT2 - Reload Register - for reading
TMR2
R
00006BH
RLT2 - Reload Register - for writing
W
00006BH
RLT2 - Reload Register - for reading
R
00006CH
RLT3 - Timer Control Status Register Low
TMCSRL3
00006DH
RLT3 - Timer Control Status Register High
TMCSRH3
00006EH
RLT3 - Reload Register - for writing
TMRLR3
W
00006EH
RLT3 - Reload Register - for reading
TMR3
R
00006FH
RLT3 - Reload Register - for writing
W
00006FH
RLT3 - Reload Register - for reading
R
000070H
RLT6 - Timer Control Status Register Low (dedic.
RLT for PPG)
TMCSRL6
000071H
RLT6 - Timer Control Status Register High (dedic.
RLT for PPG)
TMCSRH6
000072H
RLT6 - Reload Register (dedic. RLT for PPG) - for
writing
FME-MB96340 rev 10
R/W
TMCSR1
R/W
R/W
TMCSR2
R/W
R/W
TMCSR3
R/W
R/W
TMCSR6
R/W
R/W
TMRLR6
W
27
MB96340 Series
I/O map MB96(F)34x (5 of 30)
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
TMR6
R
Address
Register
000072H
RLT6 - Reload Register (dedic. RLT for PPG) - for
reading
000073H
RLT6 - Reload Register (dedic. RLT for PPG) - for
writing
W
000073H
RLT6 - Reload Register (dedic. RLT for PPG) - for
reading
R
000074H
PPG3-PPG0 - General Control register 1 Low
GCN1L0
000075H
PPG3-PPG0 - General Control register 1 High
GCN1H0
000076H
PPG3-PPG0 - General Control register 2 Low
GCN2L0
000077H
PPG3-PPG0 - General Control register 2 High
GCN2H0
000078H
PPG0 - Timer register
000079H
PPG0 - Timer register
00007AH
PPG0 - Period setting register
00007BH
PPG0 - Period setting register
00007CH
PPG0 - Duty cycle register
00007DH
PPG0 - Duty cycle register
00007EH
PPG0 - Control status register Low
PCNL0
00007FH
PPG0 - Control status register High
PCNH0
000080H
PPG1 - Timer register
000081H
PPG1 - Timer register
000082H
PPG1 - Period setting register
000083H
PPG1 - Period setting register
000084H
PPG1 - Duty cycle register
000085H
PPG1 - Duty cycle register
000086H
PPG1 - Control status register Low
PCNL1
000087H
PPG1 - Control status register High
PCNH1
000088H
PPG2 - Timer register
000089H
PPG2 - Timer register
00008AH
PPG2 - Period setting register
00008BH
PPG2 - Period setting register
00008CH
PPG2 - Duty cycle register
28
GCN10
R/W
R/W
GCN20
R/W
R/W
PTMR0
R
R
PCSR0
W
W
PDUT0
W
W
PCN0
R/W
R/W
PTMR1
R
R
PCSR1
W
W
PDUT1
W
W
PCN1
R/W
R/W
PTMR2
R
R
PCSR2
W
W
PDUT2
W
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (6 of 30)
Address
Register
Abbreviation
8-bit access
00008DH
PPG2 - Duty cycle register
00008EH
PPG2 - Control status register Low
PCNL2
00008FH
PPG2 - Control status register High
PCNH2
000090H
PPG3 - Timer register
000091H
PPG3 - Timer register
000092H
PPG3 - Period setting register
000093H
PPG3 - Period setting register
000094H
PPG3 - Duty cycle register
000095H
PPG3 - Duty cycle register
000096H
PPG3 - Control status register Low
PCNL3
000097H
PPG3 - Control status register High
PCNH3
000098H
PPG7-PPG4 - General Control register 1 Low
GCN1L1
000099H
PPG7-PPG4 - General Control register 1 High
GCN1H1
00009AH
PPG7-PPG4 - General Control register 2 Low
GCN2L1
00009BH
PPG7-PPG4 - General Control register 2 High
GCN2H1
00009CH
PPG4 - Timer register
00009DH
PPG4 - Timer register
00009EH
PPG4 - Period setting register
00009FH
PPG4 - Period setting register
0000A0H
PPG4 - Duty cycle register
0000A1H
PPG4 - Duty cycle register
0000A2H
PPG4 - Control status register Low
PCNL4
0000A3H
PPG4 - Control status register High
PCNH4
0000A4H
PPG5 - Timer register
0000A5H
PPG5 - Timer register
0000A6H
PPG5 - Period setting register
0000A7H
PPG5 - Period setting register
0000A8H
PPG5 - Duty cycle register
0000A9H
PPG5 - Duty cycle register
0000AAH
PPG5 - Control status register Low
FME-MB96340 rev 10
Abbreviation
16-bit access
Access
W
PCN2
R/W
R/W
PTMR3
R
R
PCSR3
W
W
PDUT3
W
W
PCN3
R/W
R/W
GCN11
R/W
R/W
GCN21
R/W
R/W
PTMR4
R
R
PCSR4
W
W
PDUT4
W
W
PCN4
R/W
R/W
PTMR5
R
R
PCSR5
W
W
PDUT5
W
W
PCNL5
PCN5
R/W
29
MB96340 Series
I/O map MB96(F)34x (7 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
0000ABH
PPG5 - Control status register High
PCNH5
R/W
0000ACH
I2C0 - Bus Status Register
IBSR0
R
0000ADH
I2C0 - Bus Control Register
IBCR0
R/W
0000AEH
I2C0 - Ten bit Slave address Register Low
ITBAL0
0000AFH
I2C0 - Ten bit Slave address Register High
ITBAH0
0000B0H
I2C0 - Ten bit Address mask Register Low
ITMKL0
0000B1H
I2C0 - Ten bit Address mask Register High
ITMKH0
R/W
0000B2H
I2C0 - Seven bit Slave address Register
ISBA0
R/W
0000B3H
I2C0 - Seven bit Address mask Register
ISMK0
R/W
0000B4H
I2C0 - Data Register
IDAR0
R/W
0000B5H
I2C0 - Clock Control Register
ICCR0
R/W
0000B6H
I2C1 - Bus Status Register
IBSR1
R
0000B7H
I2C1 - Bus Control Register
IBCR1
R/W
0000B8H
I2C1 - Ten bit Slave address Register Low
ITBAL1
0000B9H
I2C1 - Ten bit Slave address Register High
ITBAH1
0000BAH
I2C1 - Ten bit Address mask Register Low
ITMKL1
0000BBH
I2C1 - Ten bit Address mask Register High
ITMKH1
R/W
0000BCH
I2C1 - Seven bit Slave address Register
ISBA1
R/W
0000BDH
I2C1 - Seven bit Address mask Register
ISMK1
R/W
0000BEH
I2C1 - Data Register
IDAR1
R/W
0000BFH
I2C1 - Clock Control Register
ICCR1
R/W
0000C0H
USART0 - Serial Mode Register
SMR0
R/W
0000C1H
USART0 - Serial Control Register
SCR0
R/W
0000C2H
USART0 - TX Register
TDR0
W
0000C2H
USART0 - RX Register
RDR0
R
0000C3H
USART0 - Serial Status
SSR0
R/W
0000C4H
USART0 - Control/Com. Register
ECCR0
R/W
0000C5H
USART0 - Ext. Status Register
ESCR0
R/W
0000C6H
USART0 - Baud Rate Generator Register Low
BGRL0
0000C7H
USART0 - Baud Rate Generator Register High
BGRH0
30
ITBA0
R/W
R/W
ITMK0
ITBA1
R/W
R/W
R/W
ITMK1
BGR0
R/W
R/W
R/W
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (8 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
0000C8H
USART0 - Extended Serial Interrupt Register
0000C9H
Reserved
0000CAH
USART1 - Serial Mode Register
SMR1
R/W
0000CBH
USART1 - Serial Control Register
SCR1
R/W
0000CCH
USART1 - TX Register
TDR1
W
0000CCH
USART1 - RX Register
RDR1
R
0000CDH
USART1 - Serial Status
SSR1
R/W
0000CEH
USART1 - Control/Com. Register
ECCR1
R/W
0000CFH
USART1 - Ext. Status Register
ESCR1
R/W
0000D0H
USART1 - Baud Rate Generator Register Low
BGRL1
0000D1H
USART1 - Baud Rate Generator Register High
BGRH1
R/W
0000D2H
USART1 - Extended Serial Interrupt Register
ESIR1
R/W
0000D3H
Reserved
0000D4H
USART2 - Serial Mode Register
SMR2
R/W
0000D5H
USART2 - Serial Control Register
SCR2
R/W
0000D6H
USART2 - TX Register
TDR2
W
0000D6H
USART2 - RX Register
RDR2
R
0000D7H
USART2 - Serial Status
SSR2
R/W
0000D8H
USART2 - Control/Com. Register
ECCR2
R/W
0000D9H
USART2 - Ext. Status Register
ESCR2
R/W
0000DAH
USART2 - Baud Rate Generator Register Low
BGRL2
0000DBH
USART2 - Baud Rate Generator Register High
BGRH2
R/W
0000DCH
USART2 - Extended Serial Interrupt Register
ESIR2
R/W
0000DDH
Reserved
0000DEH
USART3 - Serial Mode Register
SMR3
R/W
0000DFH
USART3 - Serial Control Register
SCR3
R/W
0000E0H
USART3 - TX Register
TDR3
W
0000E0H
USART3 - RX Register
RDR3
R
0000E1H
USART3 - Serial Status
SSR3
R/W
0000E2H
USART3 - Control/Com. Register
ECCR3
R/W
FME-MB96340 rev 10
ESIR0
Access
R/W
-
BGR1
R/W
-
BGR2
R/W
-
31
MB96340 Series
I/O map MB96(F)34x (9 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
0000E3H
USART3 - Ext. Status Register
ESCR3
R/W
0000E4H
USART3 - Baud Rate Generator Register Low
BGRL3
0000E5H
USART3 - Baud Rate Generator Register High
BGRH3
R/W
0000E6H
USART3 - Extended Serial Interrupt Register
ESIR3
R/W
0000E7H0000EFH
Reserved
0000F0H0000FFH
External Bus area
000100H
BGR3
R/W
EXTBUS0
R/W
DMA0 - Buffer address pointer low byte
BAPL0
R/W
000101H
DMA0 - Buffer address pointer middle byte
BAPM0
R/W
000102H
DMA0 - Buffer address pointer high byte
BAPH0
R/W
000103H
DMA0 - DMA control register
DMACS0
R/W
000104H
DMA0 - I/O register address pointer low byte
IOAL0
000105H
DMA0 - I/O register address pointer high byte
IOAH0
000106H
DMA0 - Data counter low byte
DCTL0
000107H
DMA0 - Data counter high byte
DCTH0
R/W
000108H
DMA1 - Buffer address pointer low byte
BAPL1
R/W
000109H
DMA1 - Buffer address pointer middle byte
BAPM1
R/W
00010AH
DMA1 - Buffer address pointer high byte
BAPH1
R/W
00010BH
DMA1 - DMA control register
DMACS1
R/W
00010CH
DMA1 - I/O register address pointer low byte
IOAL1
00010DH
DMA1 - I/O register address pointer high byte
IOAH1
00010EH
DMA1 - Data counter low byte
DCTL1
00010FH
DMA1 - Data counter high byte
DCTH1
R/W
000110H
DMA2 - Buffer address pointer low byte
BAPL2
R/W
000111H
DMA2 - Buffer address pointer middle byte
BAPM2
R/W
000112H
DMA2 - Buffer address pointer high byte
BAPH2
R/W
000113H
DMA2 - DMA control register
DMACS2
R/W
000114H
DMA2 - I/O register address pointer low byte
IOAL2
000115H
DMA2 - I/O register address pointer high byte
IOAH2
000116H
DMA2 - Data counter low byte
DCTL2
32
IOA0
R/W
R/W
DCT0
IOA1
R/W
R/W
R/W
DCT1
IOA2
R/W
R/W
R/W
DCT2
R/W
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (10 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
000117H
DMA2 - Data counter high byte
DCTH2
R/W
000118H
DMA3 - Buffer address pointer low byte
BAPL3
R/W
000119H
DMA3 - Buffer address pointer middle byte
BAPM3
R/W
00011AH
DMA3 - Buffer address pointer high byte
BAPH3
R/W
00011BH
DMA3 - DMA control register
DMACS3
R/W
00011CH
DMA3 - I/O register address pointer low byte
IOAL3
00011DH
DMA3 - I/O register address pointer high byte
IOAH3
00011EH
DMA3 - Data counter low byte
DCTL3
00011FH
DMA3 - Data counter high byte
DCTH3
R/W
000120H
DMA4 - Buffer address pointer low byte
BAPL4
R/W
000121H
DMA4 - Buffer address pointer middle byte
BAPM4
R/W
000122H
DMA4 - Buffer address pointer high byte
BAPH4
R/W
000123H
DMA4 - DMA control register
DMACS4
R/W
000124H
DMA4 - I/O register address pointer low byte
IOAL4
000125H
DMA4 - I/O register address pointer high byte
IOAH4
000126H
DMA4 - Data counter low byte
DCTL4
000127H
DMA4 - Data counter high byte
DCTH4
R/W
000128H
DMA5 - Buffer address pointer low byte
BAPL5
R/W
000129H
DMA5 - Buffer address pointer middle byte
BAPM5
R/W
00012AH
DMA5 - Buffer address pointer high byte
BAPH5
R/W
00012BH
DMA5 - DMA control register
DMACS5
R/W
00012CH
DMA5 - I/O register address pointer low byte
IOAL5
00012DH
DMA5 - I/O register address pointer high byte
IOAH5
00012EH
DMA5 - Data counter low byte
DCTL5
00012FH
DMA5 - Data counter high byte
DCTH5
000130H00017FH
Reserved
000180H00037FH
CPU - General Purpose registers (RAM access)
000380H
000381H
IOA3
R/W
R/W
DCT3
IOA4
R/W
R/W
R/W
DCT4
IOA5
R/W
R/W
R/W
DCT5
R/W
R/W
-
GPR_RAM
R/W
DMA0 - Interrupt select
DISEL0
R/W
DMA1 - Interrupt select
DISEL1
R/W
FME-MB96340 rev 10
33
MB96340 Series
I/O map MB96(F)34x (11 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
000382H
DMA2 - Interrupt select
DISEL2
R/W
000383H
DMA3 - Interrupt select
DISEL3
R/W
000384H
DMA4 - Interrupt select
DISEL4
R/W
000385H
DMA5 - Interrupt select
DISEL5
R/W
000386H00038FH
Reserved
000390H
DMA - Status register low byte
DSRL
000391H
DMA - Status register high byte
DSRH
000392H
DMA - Stop status register low byte
DSSRL
000393H
DMA - Stop status register high byte
DSSRH
000394H
DMA - Enable register low byte
DERL
000395H
DMA - Enable register high byte
DERH
000396H00039FH
Reserved
0003A0H
Interrupt level register
ILR
0003A1H
Interrupt index register
IDX
0003A2H
Interrupt vector table base register Low
TBRL
0003A3H
Interrupt vector table base register High
TBRH
R/W
0003A4H
Delayed Interrupt register
DIRR
R/W
0003A5H
Non Maskable Interrupt register
NMI
R/W
0003A6H0003ABH
Reserved
0003ACH
EDSU communication interrupt selection Low
EDSU2L
0003ADH
EDSU communication interrupt selection High
EDSU2H
R/W
0003AEH
ROM mirror control register
ROMM
R/W
0003AFH
EDSU configuration register
EDSU
R/W
0003B0H
Memory patch control/status register ch 0/1
0003B1H
Memory patch control/status register ch 0/1
0003B2H
Memory patch control/status register ch 2/3
0003B3H
Memory patch control/status register ch 2/3
0003B4H
Memory patch control/status register ch 4/5
34
DSR
R/W
R/W
DSSR
R/W
R/W
DER
R/W
R/W
-
ICR
R/W
R/W
TBR
R/W
EDSU2
PFCS0
R/W
R/W
R/W
PFCS1
R/W
R/W
PFCS2
R/W
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (12 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
0003B5H
Memory patch control/status register ch 4/5
0003B6H
Memory patch control/status register ch 6/7
0003B7H
Memory patch control/status register ch 6/7
0003B8H
Memory Patch function - Patch address 0 low
PFAL0
R/W
0003B9H
Memory Patch function - Patch address 0 middle
PFAM0
R/W
0003BAH
Memory Patch function - Patch address 0 high
PFAH0
R/W
0003BBH
Memory Patch function - Patch address 1 low
PFAL1
R/W
0003BCH
Memory Patch function - Patch address 1 middle
PFAM1
R/W
0003BDH
Memory Patch function - Patch address 1 high
PFAH1
R/W
0003BEH
Memory Patch function - Patch address 2 low
PFAL2
R/W
0003BFH
Memory Patch function - Patch address 2 middle
PFAM2
R/W
0003C0H
Memory Patch function - Patch address 2 high
PFAH2
R/W
0003C1H
Memory Patch function - Patch address 3 low
PFAL3
R/W
0003C2H
Memory Patch function - Patch address 3 middle
PFAM3
R/W
0003C3H
Memory Patch function - Patch address 3 high
PFAH3
R/W
0003C4H
Memory Patch function - Patch address 4 low
PFAL4
R/W
0003C5H
Memory Patch function - Patch address 4 middle
PFAM4
R/W
0003C6H
Memory Patch function - Patch address 4 high
PFAH4
R/W
0003C7H
Memory Patch function - Patch address 5 low
PFAL5
R/W
0003C8H
Memory Patch function - Patch address 5 middle
PFAM5
R/W
0003C9H
Memory Patch function - Patch address 5 high
PFAH5
R/W
0003CAH
Memory Patch function - Patch address 6 low
PFAL6
R/W
0003CBH
Memory Patch function - Patch address 6 middle
PFAM6
R/W
0003CCH
Memory Patch function - Patch address 6 high
PFAH6
R/W
0003CDH
Memory Patch function - Patch address 7 low
PFAL7
R/W
0003CEH
Memory Patch function - Patch address 7 middle
PFAM7
R/W
0003CFH
Memory Patch function - Patch address 7 high
PFAH7
R/W
0003D0H
Memory Patch function - Patch data 0 Low
PFDL0
0003D1H
Memory Patch function - Patch data 0 High
PFDH0
0003D2H
Memory Patch function - Patch data 1 Low
PFDL1
FME-MB96340 rev 10
R/W
PFCS3
R/W
R/W
PFD0
R/W
R/W
PFD1
R/W
35
MB96340 Series
I/O map MB96(F)34x (13 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
0003D3H
Memory Patch function - Patch data 1 High
PFDH1
0003D4H
Memory Patch function - Patch data 2 Low
PFDL2
0003D5H
Memory Patch function - Patch data 2 High
PFDH2
0003D6H
Memory Patch function - Patch data 3 Low
PFDL3
0003D7H
Memory Patch function - Patch data 3 High
PFDH3
0003D8H
Memory Patch function - Patch data 4 Low
PFDL4
0003D9H
Memory Patch function - Patch data 4 High
PFDH4
0003DAH
Memory Patch function - Patch data 5 Low
PFDL5
0003DBH
Memory Patch function - Patch data 5 High
PFDH5
0003DCH
Memory Patch function - Patch data 6 Low
PFDL6
0003DDH
Memory Patch function - Patch data 6 High
PFDH6
0003DEH
Memory Patch function - Patch data 7 Low
PFDL7
0003DFH
Memory Patch function - Patch data 7 High
PFDH7
R/W
0003E0H
Data Flash Control and Status register A
DFCSA
R/W
0003E1H
Data Flash Write command sequencer Control
register A
DFWCA
R/W
0003E2H
Data Flash Write command sequencer Status register A
DFWSA
R/W
0003E3H0003F0H
Reserved
0003F1H
Memory Control Status Register A
MCSRA
0003F2H
Memory Timing Configuration Register A Low
MTCRAL
0003F3H
Memory Timing Configuration Register A High
MTCRAH
0003F4H
Reserved
0003F5H
Memory Control Status Register B
MCSRB
0003F6H
Memory Timing Configuration Register B Low
MTCRBL
0003F7H
Memory Timing Configuration Register B High
MTCRBH
R/W
0003F8H
Flash Memory Write Control register 0
FMWC0
R/W
0003F9H
Flash Memory Write Control register 1
FMWC1
R/W
0003FAH
Flash Memory Write Control register 2
FMWC2
R/W
0003FBH
Flash Memory Write Control register 3
FMWC3
R/W
36
R/W
PFD2
R/W
R/W
PFD3
R/W
R/W
PFD4
R/W
R/W
PFD5
R/W
R/W
PFD6
R/W
R/W
PFD7
R/W
R/W
MTCRA
R/W
R/W
R/W
MTCRB
R/W
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (14 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
0003FCH
Flash Memory Write Control register 4
FMWC4
R/W
0003FDH
Flash Memory Write Control register 5
FMWC5
R/W
0003FEH0003FFH
Reserved
000400H
Standby Mode control register
SMCR
R/W
000401H
Clock select register
CKSR
R/W
000402H
Clock Stabilization select register
CKSSR
R/W
000403H
Clock monitor register
CKMR
R
000404H
Clock Frequency control register Low
CKFCRL
000405H
Clock Frequency control register High
CKFCRH
000406H
PLL Control register Low
PLLCRL
000407H
PLL Control register High
PLLCRH
R/W
000408H
RC clock timer control register
RCTCR
R/W
000409H
Main clock timer control register
MCTCR
R/W
00040AH
Sub clock timer control register
SCTCR
R/W
00040BH
Reset cause and clock status register with clear
function
RCCSRC
R
00040CH
Reset configuration register
RCR
R/W
00040DH
Reset cause and clock status register
RCCSR
R
00040EH
Watch dog timer configuration register
WDTC
R/W
00040FH
Watch dog timer clear pattern register
WDTCP
W
000410H000414H
Reserved
000415H
Clock output activation register
000416H
-
CKFCR
R/W
R/W
PLLCR
R/W
COAR
R/W
Clock output configuration register 0
COCR0
R/W
000417H
Clock output configuration register 1
COCR1
R/W
000418H
Clock Modulator control register
CMCR
R/W
000419H
Reserved
00041AH
Clock Modulator Parameter register Low
CMPRL
00041BH
Clock Modulator Parameter register High
CMPRH
FME-MB96340 rev 10
CMPR
R/W
R/W
37
MB96340 Series
I/O map MB96(F)34x (15 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
00041CH00042BH
Reserved
00042CH
Voltage Regulator Control register
VRCR
R/W
00042DH
Clock Input and LVD Control Register
CILCR
R/W
00042EH00042FH
Reserved
000430H
I/O Port P00 - Data Direction Register
DDR00
R/W
000431H
I/O Port P01 - Data Direction Register
DDR01
R/W
000432H
I/O Port P02 - Data Direction Register
DDR02
R/W
000433H
I/O Port P03 - Data Direction Register
DDR03
R/W
000434H
I/O Port P04 - Data Direction Register
DDR04
R/W
000435H
I/O Port P05 - Data Direction Register
DDR05
R/W
000436H
I/O Port P06 - Data Direction Register
DDR06
R/W
000437H
I/O Port P07 - Data Direction Register
DDR07
R/W
000438H
I/O Port P08 - Data Direction Register
DDR08
R/W
000439H
I/O Port P09 - Data Direction Register
DDR09
R/W
00043AH
I/O Port P10 - Data Direction Register
DDR10
R/W
00043BH000443H
Reserved
000444H
I/O Port P00 - Port Input Enable Register
PIER00
R/W
000445H
I/O Port P01 - Port Input Enable Register
PIER01
R/W
000446H
I/O Port P02 - Port Input Enable Register
PIER02
R/W
000447H
I/O Port P03 - Port Input Enable Register
PIER03
R/W
000448H
I/O Port P04 - Port Input Enable Register
PIER04
R/W
000449H
I/O Port P05 - Port Input Enable Register
PIER05
R/W
00044AH
I/O Port P06 - Port Input Enable Register
PIER06
R/W
00044BH
I/O Port P07 - Port Input Enable Register
PIER07
R/W
00044CH
I/O Port P08 - Port Input Enable Register
PIER08
R/W
00044DH
I/O Port P09 - Port Input Enable Register
PIER09
R/W
00044EH
I/O Port P10 - Port Input Enable Register
PIER10
R/W
38
-
-
-
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (16 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
00044FH000457H
Reserved
000458H
I/O Port P00 - Port Input Level Register
PILR00
R/W
000459H
I/O Port P01 - Port Input Level Register
PILR01
R/W
00045AH
I/O Port P02 - Port Input Level Register
PILR02
R/W
00045BH
I/O Port P03 - Port Input Level Register
PILR03
R/W
00045CH
I/O Port P04 - Port Input Level Register
PILR04
R/W
00045DH
I/O Port P05 - Port Input Level Register
PILR05
R/W
00045EH
I/O Port P06 - Port Input Level Register
PILR06
R/W
00045FH
I/O Port P07 - Port Input Level Register
PILR07
R/W
000460H
I/O Port P08 - Port Input Level Register
PILR08
R/W
000461H
I/O Port P09 - Port Input Level Register
PILR09
R/W
000462H
I/O Port P10 - Port Input Level Register
PILR10
R/W
000463H00046BH
Reserved
00046CH
I/O Port P00 - Extended Port Input Level Register
EPILR00
R/W
00046DH
I/O Port P01 - Extended Port Input Level Register
EPILR01
R/W
00046EH
I/O Port P02 - Extended Port Input Level Register
EPILR02
R/W
00046FH
I/O Port P03 - Extended Port Input Level Register
EPILR03
R/W
000470H
I/O Port P04 - Extended Port Input Level Register
EPILR04
R/W
000471H
I/O Port P05 - Extended Port Input Level Register
EPILR05
R/W
000472H
I/O Port P06 - Extended Port Input Level Register
EPILR06
R/W
000473H
I/O Port P07 - Extended Port Input Level Register
EPILR07
R/W
000474H
I/O Port P08 - Extended Port Input Level Register
EPILR08
R/W
000475H
I/O Port P09 - Extended Port Input Level Register
EPILR09
R/W
000476H
I/O Port P10 - Extended Port Input Level Register
EPILR10
R/W
000477H00047FH
Reserved
000480H
I/O Port P00 - Port Output Drive Register
PODR00
R/W
000481H
I/O Port P01 - Port Output Drive Register
PODR01
R/W
000482H
I/O Port P02 - Port Output Drive Register
PODR02
R/W
FME-MB96340 rev 10
-
-
-
39
MB96340 Series
I/O map MB96(F)34x (17 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
000483H
I/O Port P03 - Port Output Drive Register
PODR03
R/W
000484H
I/O Port P04 - Port Output Drive Register
PODR04
R/W
000485H
I/O Port P05 - Port Output Drive Register
PODR05
R/W
000486H
I/O Port P06 - Port Output Drive Register
PODR06
R/W
000487H
I/O Port P07 - Port Output Drive Register
PODR07
R/W
000488H
I/O Port P08 - Port Output Drive Register
PODR08
R/W
000489H
I/O Port P09 - Port Output Drive Register
PODR09
R/W
00048AH
I/O Port P10 - Port Output Drive Register
PODR10
R/W
00048BH0004A7H
Reserved
0004A8H
I/O Port P00 - Pull-Up resistor Control Register
PUCR00
R/W
0004A9H
I/O Port P01 - Pull-Up resistor Control Register
PUCR01
R/W
0004AAH
I/O Port P02 - Pull-Up resistor Control Register
PUCR02
R/W
0004ABH
I/O Port P03 - Pull-Up resistor Control Register
PUCR03
R/W
0004ACH
I/O Port P04 - Pull-Up resistor Control Register
PUCR04
R/W
0004ADH
I/O Port P05 - Pull-Up resistor Control Register
PUCR05
R/W
0004AEH
I/O Port P06 - Pull-Up resistor Control Register
PUCR06
R/W
0004AFH
I/O Port P07 - Pull-Up resistor Control Register
PUCR07
R/W
0004B0H
I/O Port P08 - Pull-Up resistor Control Register
PUCR08
R/W
0004B1H
I/O Port P09 - Pull-Up resistor Control Register
PUCR09
R/W
0004B2H
I/O Port P10 - Pull-Up resistor Control Register
PUCR10
R/W
0004B3H0004BBH
Reserved
0004BCH
I/O Port P00 - External Pin State Register
EPSR00
R
0004BDH
I/O Port P01 - External Pin State Register
EPSR01
R
0004BEH
I/O Port P02 - External Pin State Register
EPSR02
R
0004BFH
I/O Port P03 - External Pin State Register
EPSR03
R
0004C0H
I/O Port P04 - External Pin State Register
EPSR04
R
0004C1H
I/O Port P05 - External Pin State Register
EPSR05
R
0004C2H
I/O Port P06 - External Pin State Register
EPSR06
R
0004C3H
I/O Port P07 - External Pin State Register
EPSR07
R
40
-
-
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (18 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
0004C4H
I/O Port P08 - External Pin State Register
EPSR08
R
0004C5H
I/O Port P09 - External Pin State Register
EPSR09
R
0004C6H
I/O Port P10 - External Pin State Register
EPSR10
R
0004C7H0004CFH
Reserved
0004D0H
ADC analog input enable register 0
ADER0
R/W
0004D1H
ADC analog input enable register 1
ADER1
R/W
0004D2H
ADC analog input enable register 2
ADER2
R/W
0004D3H
ADC analog input enable register 3
ADER3
R/W
0004D4H
ADC analog input enable register 4
ADER4
R/W
0004D5H
Reserved
0004D6H
Peripheral Resource Relocation Register 0
PRRR0
R/W
0004D7H
Peripheral Resource Relocation Register 1
PRRR1
R/W
0004D8H
Peripheral Resource Relocation Register 2
PRRR2
R/W
0004D9H
Peripheral Resource Relocation Register 3
PRRR3
R/W
0004DAH
Peripheral Resource Relocation Register 4
PRRR4
R/W
0004DBH
Peripheral Resource Relocation Register 5
PRRR5
R/W
0004DCH
Peripheral Resource Relocation Register 6
PRRR6
R/W
0004DDH
Peripheral Resource Relocation Register 7
PRRR7
R/W
0004DEH
Peripheral Resource Relocation Register 8
PRRR8
R/W
0004DFH
Peripheral Resource Relocation Register 9
PRRR9
R/W
0004E0H
RTC - Sub Second Register L
WTBRL0
0004E1H
RTC - Sub Second Register M
WTBRH0
R/W
0004E2H
RTC - Sub-Second Register H
WTBR1
R/W
0004E3H
RTC - Second Register
WTSR
R/W
0004E4H
RTC - Minutes
WTMR
R/W
0004E5H
RTC - Hour
WTHR
R/W
0004E6H
RTC - Timer Control Extended Register
WTCER
R/W
0004E7H
RTC - Clock select register
WTCKSR
R/W
0004E8H
RTC - Timer Control Register Low
FME-MB96340 rev 10
-
-
WTCRL
WTBR0
WTCR
R/W
R/W
41
MB96340 Series
I/O map MB96(F)34x (19 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
0004E9H
RTC - Timer Control Register High
0004EAH
CAL - Calibration unit Control register
0004EBH
Reserved
0004ECH
CAL - Duration Timer Data Register Low
CUTDL
0004EDH
CAL - Duration Timer Data Register High
CUTDH
0004EEH
CAL - Calibration Timer Register 2 Low
CUTR2L
0004EFH
CAL - Calibration Timer Register 2 High
CUTR2H
0004F0H
CAL - Calibration Timer Register 1 Low
CUTR1L
0004F1H
CAL - Calibration Timer Register 1 High
CUTR1H
0004F2H0004F9H
Reserved
0004FAH
RLT - Timer input select (for Cascading)
0004FBH00053DH
Reserved
00053EH
USART7 - Serial Mode Register
SMR7
R/W
00053FH
USART7 - Serial Control Register
SCR7
R/W
000540H
USART7 - Serial TX Register
TDR7
W
000540H
USART7 - Serial RX Register
RDR7
R
000541H
USART7 - Serial Status Register
SSR7
R/W
000542H
USART7 - Ext. Control/Com. Register
ECCR7
R/W
000543H
USART7 - Ext. Status Com. Register
ESCR7
R/W
000544H
USART7 - Baud Rate Generator Register Low
BGRL7
000545H
USART7 - Baud Rate Generator Register High
BGRH7
R/W
000546H
USART7 - Extended Serial Interrupt Register
ESIR7
R/W
000547H
Reserved
000548H
USART8 - Serial Mode Register
SMR8
R/W
000549H
USART8 - Serial Control Register
SCR8
R/W
00054AH
USART8 - Serial TX Register
TDR8
W
00054AH
USART8 - Serial RX Register
RDR8
R
00054BH
USART8 - Serial Status Register
SSR8
R/W
00054CH
USART8 - Ext. Control/Com. Register
ECCR8
R/W
42
WTCRH
R/W
CUCR
R/W
CUTD
R/W
R/W
CUTR2
R
R
CUTR1
R
R
-
TMISR
R/W
-
BGR7
R/W
-
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (20 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
00054DH
USART8 - Ext. Status Com. Register
ESCR8
00054EH
USART8 - Baud Rate Generator Register Low
BGRL8
00054FH
USART8 - Baud Rate Generator Register High
BGRH8
R/W
000550H
USART8 - Extended Serial Interrupt Register
ESIR8
R/W
000551H
Reserved
000552H
USART9 - Serial Mode Register
SMR9
R/W
000553H
USART9 - Serial Control Register
SCR9
R/W
000554H
USART9 - Serial TX Register
TDR9
W
000554H
USART9 - Serial RX Register
RDR9
R
000555H
USART9 - Serial Status Register
SSR9
R/W
000556H
USART9 - Ext. Control/Com. Register
ECCR9
R/W
000557H
USART9 - Ext. Status Com. Register
ESCR9
R/W
000558H
USART9 - Baud Rate Generator Register Low
BGRL9
000559H
USART9 - Baud Rate Generator Register High
BGRH9
R/W
00055AH
USART9 - Extended Serial Interrupt Register
ESIR9
R/W
00055BH00055FH
Reserved
000560H
ALARM0 - Control Status Register
000561H
ALARM0 - Extended Control Status Register
000562H
ALARM1 - Control Status Register
000563H
ALARM1 - Extended Control Status Register
000564H
PPG6 - Timer register
000565H
PPG6 - Timer register
000566H
PPG6 - Period setting register
000567H
PPG6 - Period setting register
000568H
PPG6 - Duty cycle register
000569H
PPG6 - Duty cycle register
00056AH
PPG6 - Control status register Low
PCNL6
00056BH
PPG6 - Control status register High
PCNH6
00056CH
PPG7 - Timer register
FME-MB96340 rev 10
R/W
BGR8
R/W
-
BGR9
R/W
ACSR0
R/W
AECSR0
R/W
ACSR1
R/W
AECSR1
R/W
PTMR6
R
R
PCSR6
W
W
PDUT6
W
W
PCN6
R/W
R/W
PTMR7
R
43
MB96340 Series
I/O map MB96(F)34x (21 of 30)
Address
Register
Abbreviation
8-bit access
00056DH
PPG7 - Timer register
00056EH
PPG7 - Period setting register
00056FH
PPG7 - Period setting register
000570H
PPG7 - Duty cycle register
000571H
PPG7 - Duty cycle register
000572H
PPG7 - Control status register Low
PCNL7
000573H
PPG7 - Control status register High
PCNH7
000574H
PPG11-PPG8 - General Control register 1 Low
GCN1L2
000575H
PPG11-PPG8 - General Control register 1 High
GCN1H2
000576H
PPG11-PPG8 - General Control register 2 Low
GCN2L2
000577H
PPG11-PPG8 - General Control register 2 High
GCN2H2
000578H
PPG8 - Timer register
000579H
PPG8 - Timer register
00057AH
PPG8 - Period setting register
00057BH
PPG8 - Period setting register
00057CH
PPG8 - Duty cycle register
00057DH
PPG8 - Duty cycle register
00057EH
PPG8 - Control status register Low
PCNL8
00057FH
PPG8 - Control status register High
PCNH8
000580H
PPG9 - Timer register
000581H
PPG9 - Timer register
000582H
PPG9 - Period setting register
000583H
PPG9 - Period setting register
000584H
PPG9 - Duty cycle register
000585H
PPG9 - Duty cycle register
000586H
PPG9 - Control status register Low
PCNL9
000587H
PPG9 - Control status register High
PCNH9
000588H
PPG10 - Timer register
000589H
PPG10 - Timer register
00058AH
PPG10 - Period setting register
44
Abbreviation
16-bit access
Access
R
PCSR7
W
W
PDUT7
W
W
PCN7
R/W
R/W
GCN12
R/W
R/W
GCN22
R/W
R/W
PTMR8
R
R
PCSR8
W
W
PDUT8
W
W
PCN8
R/W
R/W
PTMR9
R
R
PCSR9
W
W
PDUT9
W
W
PCN9
R/W
R/W
PTMR10
R
R
PCSR10
W
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (22 of 30)
Address
Register
Abbreviation
8-bit access
00058BH
PPG10 - Period setting register
00058CH
PPG10 - Duty cycle register
00058DH
PPG10 - Duty cycle register
00058EH
PPG10 - Control status register Low
PCNL10
00058FH
PPG10 - Control status register High
PCNH10
000590H
PPG11 - Timer register
000591H
PPG11 - Timer register
000592H
PPG11 - Period setting register
000593H
PPG11 - Period setting register
000594H
PPG11 - Duty cycle register
000595H
PPG11 - Duty cycle register
000596H
PPG11 - Control status register Low
PCNL11
000597H
PPG11 - Control status register High
PCNH11
000598H
PPG15-PPG12 - General Control register 1 Low
GCN1L3
000599H
PPG15-PPG12 - General Control register 1 High
GCN1H3
00059AH
PPG15-PPG12 - General Control register 2 Low
GCN2L3
00059BH
PPG15-PPG12 - General Control register 2 High
GCN2H3
00059CH
PPG12 - Timer register
00059DH
PPG12 - Timer register
00059EH
PPG12 - Period setting register
00059FH
PPG12 - Period setting register
0005A0H
PPG12 - Duty cycle register
0005A1H
PPG12 - Duty cycle register
0005A2H
PPG12 - Control status register Low
PCNL12
0005A3H
PPG12 - Control status register High
PCNH12
0005A4H
PPG13 - Timer register
0005A5H
PPG13 - Timer register
0005A6H
PPG13 - Period setting register
0005A7H
PPG13 - Period setting register
0005A8H
PPG13 - Duty cycle register
FME-MB96340 rev 10
Abbreviation
16-bit access
Access
W
PDUT10
W
W
PCN10
R/W
R/W
PTMR11
R
R
PCSR11
W
W
PDUT11
W
W
PCN11
R/W
R/W
GCN13
R/W
R/W
GCN23
R/W
R/W
PTMR12
R
R
PCSR12
W
W
PDUT12
W
W
PCN12
R/W
R/W
PTMR13
R
R
PCSR13
W
W
PDUT13
W
45
MB96340 Series
I/O map MB96(F)34x (23 of 30)
Address
Register
Abbreviation
8-bit access
0005A9H
PPG13 - Duty cycle register
0005AAH
PPG13 - Control status register Low
PCNL13
0005ABH
PPG13 - Control status register High
PCNH13
0005ACH
PPG14 - Timer register
0005ADH
PPG14 - Timer register
0005AEH
PPG14 - Period setting register
0005AFH
PPG14 - Period setting register
0005B0H
PPG14 - Duty cycle register
0005B1H
PPG14 - Duty cycle register
0005B2H
PPG14 - Control status register Low
PCNL14
0005B3H
PPG14 - Control status register High
PCNH14
0005B4H
PPG15 - Timer register
0005B5H
PPG15 - Timer register
0005B6H
PPG15 - Period setting register
0005B7H
PPG15 - Period setting register
0005B8H
PPG15 - Duty cycle register
0005B9H
PPG15 - Duty cycle register
0005BAH
PPG15 - Control status register Low
PCNL15
0005BBH
PPG15 - Control status register High
PCNH15
0005BCH00065FH
Reserved
Abbreviation
16-bit access
Access
W
PCN13
R/W
R/W
PTMR14
R
R
PCSR14
W
W
PDUT14
W
W
PCN14
R/W
R/W
PTMR15
R
R
PCSR15
W
W
PDUT15
W
W
PCN15
R/W
R/W
-
000660H
Peripheral Resource Relocation Register 10
PRRR10
R/W
000661H
Peripheral Resource Relocation Register 11
PRRR11
R/W
000662H
Peripheral Resource Relocation Register 12
PRRR12
R/W
000663H
Peripheral Resource Relocation Register 13
PRRR13
W
000664H0006DFH
Reserved
0006E0H
External Bus - Area configuration register 0 Low
EACL0
0006E1H
External Bus - Area configuration register 0 High
EACH0
0006E2H
External Bus - Area configuration register 1 Low
EACL1
0006E3H
External Bus - Area configuration register 1 High
EACH1
46
EAC0
R/W
R/W
EAC1
R/W
R/W
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (24 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
EAC2
R/W
0006E4H
External Bus - Area configuration register 2 Low
EACL2
0006E5H
External Bus - Area configuration register 2 High
EACH2
0006E6H
External Bus - Area configuration register 3 Low
EACL3
0006E7H
External Bus - Area configuration register 3 High
EACH3
0006E8H
External Bus - Area configuration register 4 Low
EACL4
0006E9H
External Bus - Area configuration register 4 High
EACH4
0006EAH
External Bus - Area configuration register 5 Low
EACL5
0006EBH
External Bus - Area configuration register 5 High
EACH5
R/W
0006ECH
External Bus - Area select register 2
EAS2
R/W
0006EDH
External Bus - Area select register 3
EAS3
R/W
0006EEH
External Bus - Area select register 4
EAS4
R/W
0006EFH
External Bus - Area select register 5
EAS5
R/W
0006F0H
External Bus - Mode register
EBM
R/W
0006F1H
External Bus - Clock and Function register
EBCF
R/W
0006F2H
External Bus - Address output enable register 0
EBAE0
R/W
0006F3H
External Bus - Address output enable register 1
EBAE1
R/W
0006F4H
External Bus - Address output enable register 2
EBAE2
R/W
0006F5H
External Bus - Control signal register
EBCS
R/W
0006F6H0006FFH
Reserved
000700H
CAN0 - Control register Low
CTRLRL0
000701H
CAN0 - Control register High (reserved)
CTRLRH0
000702H
CAN0 - Status register Low
STATRL0
000703H
CAN0 - Status register High (reserved)
STATRH0
000704H
CAN0 - Error Counter Low (Transmit)
ERRCNTL0
000705H
CAN0 - Error Counter High (Receive)
ERRCNTH0
000706H
CAN0 - Bit Timing Register Low
BTRL0
000707H
CAN0 - Bit Timing Register High
BTRH0
000708H
CAN0 - Interrupt Register Low
INTRL0
000709H
CAN0 - Interrupt Register High
INTRH0
FME-MB96340 rev 10
R/W
EAC3
R/W
R/W
EAC4
R/W
R/W
EAC5
R/W
CTRLR0
R/W
R
STATR0
R/W
R
ERRCNT0
R
R
BTR0
R/W
R/W
INTR0
R
R
47
MB96340 Series
I/O map MB96(F)34x (25 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
TESTR0
R/W
00070AH
CAN0 - Test Register Low
TESTRL0
00070BH
CAN0 - Test Register High (reserved)
TESTRH0
00070CH
CAN0 - BRP Extension register Low
BRPERL0
00070DH
CAN0 - BRP Extension register High (reserved)
BRPERH0
00070EH00070FH
Reserved
000710H
CAN0 - IF1 Command request register Low
IF1CREQL0
000711H
CAN0 - IF1 Command request register High
IF1CREQH0
000712H
CAN0 - IF1 Command Mask register Low
IF1CMSKL0
000713H
CAN0 - IF1 Command Mask register High (reserved)
IF1CMSKH0
000714H
CAN0 - IF1 Mask 1 Register Low
IF1MSK1L0
000715H
CAN0 - IF1 Mask 1 Register High
IF1MSK1H0
000716H
CAN0 - IF1 Mask 2 Register Low
IF1MSK2L0
000717H
CAN0 - IF1 Mask 2 Register High
IF1MSK2H0
000718H
CAN0 - IF1 Arbitration 1 Register Low
IF1ARB1L0
000719H
CAN0 - IF1 Arbitration 1 Register High
IF1ARB1H0
00071AH
CAN0 - IF1 Arbitration 2 Register Low
IF1ARB2L0
00071BH
CAN0 - IF1 Arbitration 2 Register High
IF1ARB2H0
00071CH
CAN0 - IF1 Message Control Register Low
IF1MCTRL0
00071DH
CAN0 - IF1 Message Control Register High
IF1MCTRH0
00071EH
CAN0 - IF1 Data A1 Low
IF1DTA1L0
00071FH
CAN0 - IF1 Data A1 High
IF1DTA1H0
000720H
CAN0 - IF1 Data A2 Low
IF1DTA2L0
000721H
CAN0 - IF1 Data A2 High
IF1DTA2H0
000722H
CAN0 - IF1 Data B1 Low
IF1DTB1L0
000723H
CAN0 - IF1 Data B1 High
IF1DTB1H0
000724H
CAN0 - IF1 Data B2 Low
IF1DTB2L0
000725H
CAN0 - IF1 Data B2 High
IF1DTB2H0
000726H00073FH
Reserved
48
R
BRPER0
R/W
R
-
IF1CREQ0
R/W
R/W
IF1CMSK0
R/W
R
IF1MSK10
R/W
R/W
IF1MSK20
R/W
R/W
IF1ARB10
R/W
R/W
IF1ARB20
R/W
R/W
IF1MCTR0
R/W
R/W
IF1DTA10
R/W
R/W
IF1DTA20
R/W
R/W
IF1DTB10
R/W
R/W
IF1DTB20
R/W
R/W
-
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (26 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
IF2CREQ0
R/W
000740H
CAN0 - IF2 Command request register Low
IF2CREQL0
000741H
CAN0 - IF2 Command request register High
IF2CREQH0
000742H
CAN0 - IF2 Command Mask register Low
IF2CMSKL0
000743H
CAN0 - IF2 Command Mask register High (reserved)
IF2CMSKH0
000744H
CAN0 - IF2 Mask 1 Register Low
IF2MSK1L0
000745H
CAN0 - IF2 Mask 1 Register High
IF2MSK1H0
000746H
CAN0 - IF2 Mask 2 Register Low
IF2MSK2L0
000747H
CAN0 - IF2 Mask 2 Register High
IF2MSK2H0
000748H
CAN0 - IF2 Arbitration 1 Register Low
IF2ARB1L0
000749H
CAN0 - IF2 Arbitration 1 Register High
IF2ARB1H0
00074AH
CAN0 - IF2 Arbitration 2 Register Low
IF2ARB2L0
00074BH
CAN0 - IF2 Arbitration 2 Register High
IF2ARB2H0
00074CH
CAN0 - IF2 Message Control Register Low
IF2MCTRL0
00074DH
CAN0 - IF2 Message Control Register High
IF2MCTRH0
00074EH
CAN0 - IF2 Data A1 Low
IF2DTA1L0
00074FH
CAN0 - IF2 Data A1 High
IF2DTA1H0
000750H
CAN0 - IF2 Data A2 Low
IF2DTA2L0
000751H
CAN0 - IF2 Data A2 High
IF2DTA2H0
000752H
CAN0 - IF2 Data B1 Low
IF2DTB1L0
000753H
CAN0 - IF2 Data B1 High
IF2DTB1H0
000754H
CAN0 - IF2 Data B2 Low
IF2DTB2L0
000755H
CAN0 - IF2 Data B2 High
IF2DTB2H0
000756H00077FH
Reserved
000780H
CAN0 - Transmission Request 1 Register Low
TREQR1L0
000781H
CAN0 - Transmission Request 1 Register High
TREQR1H0
000782H
CAN0 - Transmission Request 2 Register Low
TREQR2L0
000783H
CAN0 - Transmission Request 2 Register High
TREQR2H0
000784H00078FH
Reserved
FME-MB96340 rev 10
R/W
IF2CMSK0
R/W
R
IF2MSK10
R/W
R/W
IF2MSK20
R/W
R/W
IF2ARB10
R/W
R/W
IF2ARB20
R/W
R/W
IF2MCTR0
R/W
R/W
IF2DTA10
R/W
R/W
IF2DTA20
R/W
R/W
IF2DTB10
R/W
R/W
IF2DTB20
R/W
R/W
-
TREQR10
R
R
TREQR20
R
R
-
49
MB96340 Series
I/O map MB96(F)34x (27 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
NEWDT10
R
000790H
CAN0 - New Data 1 Register Low
NEWDT1L0
000791H
CAN0 - New Data 1 Register High
NEWDT1H0
000792H
CAN0 - New Data 2 Register Low
NEWDT2L0
000793H
CAN0 - New Data 2 Register High
NEWDT2H0
000794H00079FH
Reserved
0007A0H
CAN0 - Interrupt Pending 1 Register Low
INTPND1L0
0007A1H
CAN0 - Interrupt Pending 1 Register High
INTPND1H0
0007A2H
CAN0 - Interrupt Pending 2 Register Low
INTPND2L0
0007A3H
CAN0 - Interrupt Pending 2 Register High
INTPND2H0
0007A4H0007AFH
Reserved
0007B0H
CAN0 - Message Valid 1 Register Low
MSGVAL1L0
0007B1H
CAN0 - Message Valid 1 Register High
MSGVAL1H0
0007B2H
CAN0 - Message Valid 2 Register Low
MSGVAL2L0
0007B3H
CAN0 - Message Valid 2 Register High
MSGVAL2H0
0007B4H0007CDH
Reserved
0007CEH
CAN0 - Output enable register
0007CFH0007FFH
Reserved
000800H
CAN1 - Control register Low
CTRLRL1
000801H
CAN1 - Control register High (reserved)
CTRLRH1
000802H
CAN1 - Status register Low
STATRL1
000803H
CAN1 - Status register High (reserved)
STATRH1
000804H
CAN1 - Error Counter Low (Transmit)
ERRCNTL1
000805H
CAN1 - Error Counter High (Receive)
ERRCNTH1
000806H
CAN1 - Bit Timing Register Low
BTRL1
000807H
CAN1 - Bit Timing Register High
BTRH1
000808H
CAN1 - Interrupt Register Low
INTRL1
000809H
CAN1 - Interrupt Register High
INTRH1
50
R
NEWDT20
R
R
-
INTPND10
R
R
INTPND20
R
R
-
MSGVAL10
R
R
MSGVAL20
R
R
-
COER0
R/W
CTRLR1
R/W
R
STATR1
R/W
R
ERRCNT1
R
R
BTR1
R/W
R/W
INTR1
R
R
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (28 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
TESTR1
R/W
00080AH
CAN1 - Test Register Low
TESTRL1
00080BH
CAN1 - Test Register High (reserved)
TESTRH1
00080CH
CAN1 - BRP Extension register Low
BRPERL1
00080DH
CAN1 - BRP Extension register High (reserved)
BRPERH1
00080EH00080FH
Reserved
000810H
CAN1 - IF1 Command request register Low
IF1CREQL1
000811H
CAN1 - IF1 Command request register High
IF1CREQH1
000812H
CAN1 - IF1 Command Mask register Low
IF1CMSKL1
000813H
CAN1 - IF1 Command Mask register High (reserved)
IF1CMSKH1
000814H
CAN1 - IF1 Mask 1 Register Low
IF1MSK1L1
000815H
CAN1 - IF1 Mask 1 Register High
IF1MSK1H1
000816H
CAN1 - IF1 Mask 2 Register Low
IF1MSK2L1
000817H
CAN1 - IF1 Mask 2 Register High
IF1MSK2H1
000818H
CAN1 - IF1 Arbitration 1 Register Low
IF1ARB1L1
000819H
CAN1 - IF1 Arbitration 1 Register High
IF1ARB1H1
00081AH
CAN1 - IF1 Arbitration 2 Register Low
IF1ARB2L1
00081BH
CAN1 - IF1 Arbitration 2 Register High
IF1ARB2H1
00081CH
CAN1 - IF1 Message Control Register Low
IF1MCTRL1
00081DH
CAN1 - IF1 Message Control Register High
IF1MCTRH1
00081EH
CAN1 - IF1 Data A1 Low
IF1DTA1L1
00081FH
CAN1 - IF1 Data A1 High
IF1DTA1H1
000820H
CAN1 - IF1 Data A2 Low
IF1DTA2L1
000821H
CAN1 - IF1 Data A2 High
IF1DTA2H1
000822H
CAN1 - IF1 Data B1 Low
IF1DTB1L1
000823H
CAN1 - IF1 Data B1 High
IF1DTB1H1
000824H
CAN1 - IF1 Data B2 Low
IF1DTB2L1
000825H
CAN1 - IF1 Data B2 High
IF1DTB2H1
000826H00083FH
Reserved
FME-MB96340 rev 10
R
BRPER1
R/W
R
-
IF1CREQ1
R/W
R/W
IF1CMSK1
R/W
R
IF1MSK11
R/W
R/W
IF1MSK21
R/W
R/W
IF1ARB11
R/W
R/W
IF1ARB21
R/W
R/W
IF1MCTR1
R/W
R/W
IF1DTA11
R/W
R/W
IF1DTA21
R/W
R/W
IF1DTB11
R/W
R/W
IF1DTB21
R/W
R/W
-
51
MB96340 Series
I/O map MB96(F)34x (29 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
IF2CREQ1
R/W
000840H
CAN1 - IF2 Command request register Low
IF2CREQL1
000841H
CAN1 - IF2 Command request register High
IF2CREQH1
000842H
CAN1 - IF2 Command Mask register Low
IF2CMSKL1
000843H
CAN1 - IF2 Command Mask register High (reserved)
IF2CMSKH1
000844H
CAN1 - IF2 Mask 1 Register Low
IF2MSK1L1
000845H
CAN1 - IF2 Mask 1 Register High
IF2MSK1H1
000846H
CAN1 - IF2 Mask 2 Register Low
IF2MSK2L1
000847H
CAN1 - IF2 Mask 2 Register High
IF2MSK2H1
000848H
CAN1 - IF2 Arbitration 1 Register Low
IF2ARB1L1
000849H
CAN1 - IF2 Arbitration 1 Register High
IF2ARB1H1
00084AH
CAN1 - IF2 Arbitration 2 Register Low
IF2ARB2L1
00084BH
CAN1 - IF2 Arbitration 2 Register High
IF2ARB2H1
00084CH
CAN1 - IF2 Message Control Register Low
IF2MCTRL1
00084DH
CAN1 - IF2 Message Control Register High
IF2MCTRH1
00084EH
CAN1 - IF2 Data A1 Low
IF2DTA1L1
00084FH
CAN1 - IF2 Data A1 High
IF2DTA1H1
000850H
CAN1 - IF2 Data A2 Low
IF2DTA2L1
000851H
CAN1 - IF2 Data A2 High
IF2DTA2H1
000852H
CAN1 - IF2 Data B1 Low
IF2DTB1L1
000853H
CAN1 - IF2 Data B1 High
IF2DTB1H1
000854H
CAN1 - IF2 Data B2 Low
IF2DTB2L1
000855H
CAN1 - IF2 Data B2 High
IF2DTB2H1
000856H00087FH
Reserved
000880H
CAN1 - Transmission Request 1 Register Low
TREQR1L1
000881H
CAN1 - Transmission Request 1 Register High
TREQR1H1
000882H
CAN1 - Transmission Request 2 Register Low
TREQR2L1
000883H
CAN1 - Transmission Request 2 Register High
TREQR2H1
000884H00088FH
Reserved
52
R/W
IF2CMSK1
R/W
R
IF2MSK11
R/W
R/W
IF2MSK21
R/W
R/W
IF2ARB11
R/W
R/W
IF2ARB21
R/W
R/W
IF2MCTR1
R/W
R/W
IF2DTA11
R/W
R/W
IF2DTA21
R/W
R/W
IF2DTB11
R/W
R/W
IF2DTB21
R/W
R/W
-
TREQR11
R
R
TREQR21
R
R
-
FME-MB96340 rev 10
MB96340 Series
I/O map MB96(F)34x (30 of 30)
Address
Register
Abbreviation
8-bit access
Abbreviation
16-bit access
Access
NEWDT11
R
000890H
CAN1 - New Data 1 Register Low
NEWDT1L1
000891H
CAN1 - New Data 1 Register High
NEWDT1H1
000892H
CAN1 - New Data 2 Register Low
NEWDT2L1
000893H
CAN1 - New Data 2 Register High
NEWDT2H1
000894H00089FH
Reserved
0008A0H
CAN1 - Interrupt Pending 1 Register Low
INTPND1L1
0008A1H
CAN1 - Interrupt Pending 1 Register High
INTPND1H1
0008A2H
CAN1 - Interrupt Pending 2 Register Low
INTPND2L1
0008A3H
CAN1 - Interrupt Pending 2 Register High
INTPND2H1
0008A4H0008AFH
Reserved
0008B0H
CAN1 - Message Valid 1 Register Low
MSGVAL1L1
0008B1H
CAN1 - Message Valid 1 Register High
MSGVAL1H1
0008B2H
CAN1 - Message Valid 2 Register Low
MSGVAL2L1
0008B3H
CAN1 - Message Valid 2 Register High
MSGVAL2H1
0008B4H0008CDH
Reserved
0008CEH
CAN1 - Output enable register
0008CFH0009FFH
Reserved
000A00H
DMA - IO address block register 0
IOABK0
R/W
000A01H
DMA - IO address block register 1
IOABK1
R/W
000A02H
DMA - IO address block register 2
IOABK2
R/W
000A03H
DMA - IO address block register 3
IOABK3
R/W
000A04H
DMA - IO address block register 4
IOABK4
R/W
000A05H
DMA - IO address block register 5
IOABK5
R/W
000A06H000BFFH
Reserved
R
NEWDT21
R
R
-
INTPND11
R
R
INTPND21
R
R
-
MSGVAL11
R
R
MSGVAL21
R
R
-
COER1
R/W
-
-
Note: Any write access to reserved addresses in the I/O map should not be performed. A read access to a reserved
address results in reading ‘X’.
Registers of resources which are described in this table, but which are not supported by the device, should
also be handled as “Reserved”.
FME-MB96340 rev 10
53
MB96340 Series
■ INTERRUPT VECTOR TABLE
Interrupt vector table MB96(F)34x (1 of 4)
Vector
number
Offset in
vector table
Vector name
Cleared
by DMA
Index in
ICR to
program
0
3FCH
CALLV0
No
-
1
3F8H
CALLV1
No
-
2
3F4H
CALLV2
No
-
3
3F0H
CALLV3
No
-
4
3ECH
CALLV4
No
-
5
3E8H
CALLV5
No
-
6
3E4H
CALLV6
No
-
7
3E0H
CALLV7
No
-
8
3DCH
RESET
No
-
9
3D8H
INT9
No
-
10
3D4H
EXCEPTION
No
-
11
3D0H
NMI
No
-
12
3CCH
DLY
No
12
Delayed Interrupt
13
3C8H
RC_TIMER
No
13
RC Timer
14
3C4H
MC_TIMER
No
14
Main Clock Timer
15
3C0H
SC_TIMER
No
15
Sub Clock Timer
16
3BCH
RESERVED
No
16
Reserved
17
3B8H
EXTINT0
Yes
17
External Interrupt 0
18
3B4H
EXTINT1
Yes
18
External Interrupt 1
19
3B0H
EXTINT2
Yes
19
External Interrupt 2
20
3ACH
EXTINT3
Yes
20
External Interrupt 3
21
3A8H
EXTINT4
Yes
21
External Interrupt 4
22
3A4H
EXTINT5
Yes
22
External Interrupt 5
23
3A0H
EXTINT6
Yes
23
External Interrupt 6
24
39CH
EXTINT7
Yes
24
External Interrupt 7
25
398H
EXTINT8
Yes
25
External Interrupt 8
26
394H
EXTINT9
Yes
26
External Interrupt 9
27
390H
EXTINT10
Yes
27
External Interrupt 10
54
Description
Non-Maskable Interrupt
FME-MB96340 rev 10
MB96340 Series
Interrupt vector table MB96(F)34x (2 of 4)
Vector
number
Offset in
vector table
Vector name
Cleared
by DMA
Index in
ICR to
program
28
38CH
EXTINT11
Yes
28
External Interrupt 11
29
388H
EXTINT12
Yes
29
External Interrupt 12
30
384H
EXTINT13
Yes
30
External Interrupt 13
31
380H
EXTINT14
Yes
31
External Interrupt 14
32
37CH
EXTINT15
Yes
32
External Interrupt 15
33
378H
CAN0
No
33
CAN Controller 0 (except
MB96(F)34xAyy or MB96(F)34xCyy)
34
374H
CAN1
No
34
CAN Controller 1 (except
MB96(F)34xAyy, MB96(F)34xCyy,
MB96F345Dyy or MB96F345Fyy)
35
370H
PPG0
Yes
35
Programmable Pulse Generator 0
36
36CH
PPG1
Yes
36
Programmable Pulse Generator 1
37
368H
PPG2
Yes
37
Programmable Pulse Generator 2
38
364H
PPG3
Yes
38
Programmable Pulse Generator 3
39
360H
PPG4
Yes
39
Programmable Pulse Generator 4
40
35CH
PPG5
Yes
40
Programmable Pulse Generator 5
41
358H
PPG6
Yes
41
Programmable Pulse Generator 6
42
354H
PPG7
Yes
42
Programmable Pulse Generator 7
43
350H
PPG8
Yes
43
Programmable Pulse Generator 8
44
34CH
PPG9
Yes
44
Programmable Pulse Generator 9
45
348H
PPG10
Yes
45
Programmable Pulse Generator 10
46
344H
PPG11
Yes
46
Programmable Pulse Generator 11
47
340H
PPG12
Yes
47
Programmable Pulse Generator 12
48
33CH
PPG13
Yes
48
Programmable Pulse Generator 13
49
338H
PPG14
Yes
49
Programmable Pulse Generator 14
50
334H
PPG15
Yes
50
Programmable Pulse Generator 15
51
330H
RLT0
Yes
51
Reload Timer 0
52
32CH
RLT1
Yes
52
Reload Timer 1
53
328H
RLT2
Yes
53
Reload Timer 2
54
324H
RLT3
Yes
54
Reload Timer 3
FME-MB96340 rev 10
Description
55
MB96340 Series
Interrupt vector table MB96(F)34x (3 of 4)
Vector
number
Offset in
vector table
Vector name
Cleared
by DMA
Index in
ICR to
program
55
320H
PPGRLT
Yes
55
Reload Timer 6 - dedicated for PPG
56
31CH
ICU0
Yes
56
Input Capture Unit 0
57
318H
ICU1
Yes
57
Input Capture Unit 1
58
314H
ICU2
Yes
58
Input Capture Unit 2
59
310H
ICU3
Yes
59
Input Capture Unit 3
60
30CH
ICU4
Yes
60
Input Capture Unit 4
61
308H
ICU5
Yes
61
Input Capture Unit 5
62
304H
ICU6
Yes
62
Input Capture Unit 6
63
300H
ICU7
Yes
63
Input Capture Unit 7
64
2FCH
OCU0
Yes
64
Output Compare Unit 0
65
2F8H
OCU1
Yes
65
Output Compare Unit 1
66
2F4H
OCU2
Yes
66
Output Compare Unit 2
67
2F0H
OCU3
Yes
67
Output Compare Unit 3
68
2ECH
OCU4
Yes
68
Output Compare Unit 4
69
2E8H
OCU5
Yes
69
Output Compare Unit 5
70
2E4H
OCU6
Yes
70
Output Compare Unit 6
71
2E0H
OCU7
Yes
71
Output Compare Unit 7
72
2DCH
FRT0
Yes
72
Free Running Timer 0
73
2D8H
FRT1
Yes
73
Free Running Timer 1
74
2D4H
IIC0
Yes
74
I2C interface
75
2D0H
IIC1
Yes
75
I2C interface
76
2CCH
ADC0
Yes
76
A/D Converter
77
2C8H
ALARM0
No
77
Alarm Comparator 0 (except
MB96F345Dyy or MB96F345Fyy)
78
2C4H
ALARM1
No
78
Alarm Comparator 1 (except
MB96F345Dyy or MB96F345Fyy)
79
2C0H
LINR0
Yes
79
LIN USART 0 RX
80
2BCH
LINT0
Yes
80
LIN USART 0 TX
81
2B8H
LINR1
Yes
81
LIN USART 1 RX
82
2B4H
LINT1
Yes
82
LIN USART 1 TX
56
Description
FME-MB96340 rev 10
MB96340 Series
Interrupt vector table MB96(F)34x (4 of 4)
Vector
number
Offset in
vector table
Vector name
Cleared
by DMA
Index in
ICR to
program
83
2B0H
LINR2
Yes
83
LIN USART 2 RX
84
2ACH
LINT2
Yes
84
LIN USART 2 TX
85
2A8H
LINR3
Yes
85
LIN USART 3 RX
86
2A4H
LINT3
Yes
86
LIN USART 3 TX
87
2A0H
FLASH_A
No
87
Flash memory A (only Flash devices)
88
29CH
FLASH_B
No
88
Flash memory B
(only MB96F348T/H/C)
89
298H
LINR7
Yes
89
LIN USART 7 RX
90
294H
LINT7
Yes
90
LIN USART 7 TX
91
290H
LINR8
Yes
91
LIN USART 8 RX
92
28CH
LINT8
Yes
92
LIN USART 8 TX
93
288H
LINR9
Yes
93
LIN USART 9 RX
94
284H
LINT9
Yes
94
LIN USART 9 TX
95
280H
RTC0
No
95
Real Timer Clock
96
27CH
CAL0
No
96
Clock Calibration Unit
97
278H
DFLASH_A
Yes
97
Data Flash A
(only MB96F345Dyy, MB96F345Fyy)
FME-MB96340 rev 10
Description
57
MB96340 Series
■ HANDLING DEVICES
Special care is required for the following when handling the device:
•
•
•
•
•
•
•
•
•
•
•
•
•
Latch-up prevention
Unused pins handling
External clock usage
Unused sub clock signal
Notes on PLL clock mode operation
Power supply pins (VCC/VSS)
Crystal oscillator circuit
Turn on sequence of power supply to A/D converter and analog inputs
Pin handling when not using the A/D converter
Notes on energization
Stabilization of power supply voltage
Serial communication
Handling of Data Flash
1. Latch-up prevention
CMOS IC chips may suffer latch-up under the following conditions:
• A voltage higher than VCC or lower than VSS is applied to an input or output pin.
• A voltage higher than the rated voltage is applied between VCC pins and VSS pins.
• The AVCC power supply is applied before the VCC voltage.
Latch-up may increase the power supply current dramatically, causing thermal damages to the device.
For the same reason, extra care is required to not let the analog power-supply voltage (AVCC, AVRH) exceed
the digital power-supply voltage.
2. Unused pins handling
Unused input pins can be left open when the input is disabled (corresponding bit of Port Input Enable register
PIER = 0).
Leaving unused input pins open when the input is enabled may result in misbehavior and possible permanent
damage of the device. They must therefore be pulled up or pulled down through resistors. To prevent latch-up,
those resistors should be more than 2 kΩ.
Unused bidirectional pins can be set either to the output state and be then left open, or to the input state with
either input disabled or external pull-up/pull-down resistor as described above.
3. External clock usage
The permitted frequency range of an external clock depends on the oscillator type and configuration. See AC
Characteristics for detailed modes and frequency limits. Single and opposite phase external clocks must be
connected as follows:
1. Single phase external clock
• When using a single phase external clock, X0 (X0A) pin must be driven and X1 (X1A) pin left open.
X0
X1
58
FME-MB96340 rev 10
MB96340 Series
2. Opposite phase external clock
• When using an opposite phase external clock, X1 (X1A) must be supplied with a clock signal which has the
opposite phase to the X0 (X0A) pins.
X0
X1
4. Unused sub clock signal
If the pins X0A and X1A are not connected to an oscillator, a pull-down resistor must be connected on the X0A
pin and the X1A pin must be left open.
5. Notes on PLL clock mode operation
If the PLL clock mode is selected and no external oscillator is operating or no external clock is supplied, the
microcontroller attempts to work with the free oscillating PLL. Performance of this operation, however, cannot
be guaranteed.
6. Power supply pins (VCC/VSS)
It is required that all VCC-level as well as all VSS-level power supply pins are at the same potential. If there is more
than one VCC or VSS level, the device may operate incorrectly or be damaged even within the guaranteed operating
range.
VCC and VSS must be connected to the device from the power supply with lowest possible impedance.
As a measure against power supply noise, it is required to connect a bypass capacitor of about 0.1 µF between
VCC and VSS as close as possible to VCC and VSS pins.
7. Crystal oscillator and ceramic resonator circuit
Noise at X0, X1 pins or X0A, X1A pins might cause abnormal operation. It is required to provide bypass capacitors
with shortest possible distance to X0, X1 pins and X0A, X1A pins, crystal oscillator (or ceramic resonator) and
ground lines, and, to the utmost effort, that the lines of oscillation circuit do not cross the lines of other circuits.
It is highly recommended to provide a printed circuit board art work surrounding X0, X1 pins and X0A, X1A pins
with a ground area for stabilizing the operation.
It is highly recommended to evaluate the quartz/MCU or resonator/MCU system at the quartz or resonator
manufacturer, especially when using low-Q resonators at higher frequencies.
8. Turn on sequence of power supply to A/D converter and analog inputs
It is required to turn the A/D converter power supply (AVCC, AVRH, AVRL) and analog inputs (ANn) on after
turning the digital power supply (VCC) on.
It is also required to turn the digital power off after turning the A/D converter supply and analog inputs off. In this
case, the voltage must not exceed AVRH or AVCC (turning the analog and digital power supplies simultaneously
on or off is acceptable).
9. Pin handling when not using the A/D converter
It is required to connect the unused pins of the A/D converter as AVCC = VCC, AVSS = AVRH = AVRL = VSS.
10. Notes on Power-on
To prevent malfunction of the internal voltage regulator, supply voltage profile while turning the power supply on
should be slower than 50µs from 0.2 V to 2.7 V.
FME-MB96340 rev 10
59
MB96340 Series
11. Stabilization of power supply voltage
If the power supply voltage varies acutely even within the operation safety range of the Vcc power supply voltage,
a malfunction may occur. The Vcc power supply voltage must therefore be stabilized. As stabilization guidelines,
the power supply voltage must be stabilized in such a way that Vcc ripple fluctuations (peak to peak value) in
the commercial frequencies (50 to 60 Hz) fall within 10% of the standard Vcc power supply voltage and the
transient fluctuation rate becomes 0.1V/µs or less in instantaneous fluctuation for power supply switching.
12. Serial communication
There is a possibility to receive wrong data due to noise or other causes on the serial communication.
Therefore, design a printed circuit board so as to avoid noise.
Consider receiving of wrong data when designing the system. For example apply a checksum and retransmit
the data if an error occurs.
13. Handling of Data Flash
The Data Flash requires different and additional control signals for parallel programming. Please check with
your programming equipment maker for support of this interface.
60
FME-MB96340 rev 10
MB96340 Series
■ ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
Parameter
Symbol
Rating
Min
Max
Unit
Remarks
VCC
VSS - 0.3 VSS + 6.0
V
AVCC
VSS - 0.3 VSS + 6.0
V
VCC = AVCC *1
AVRH,
AVRL
VSS - 0.3 VSS + 6.0
V
AVCC ≥ AVRH, AVCC ≥ AVRL,
AVRH > AVRL, AVRL ≥ AVSS
Input voltage
VI
VSS - 0.3 VSS + 6.0
V
VI ≤ VCC + 0.3V
Output voltage
VO
VSS - 0.3 VSS + 6.0
V
VO ≤ VCC + 0.3V *2
Power supply voltage
AD Converter voltage references
*2
ICLAMP
-4.0
+4.0
mA
Applicable to general purpose
I/O pins *3
Σ|ICLAMP|
-
40
mA
Applicable to general purpose
I/O pins *3
IOL1
-
15
mA Normal outputs with driving
strength set to 5mA
“L” level average output current
IOLAV1
-
5
mA Normal outputs with driving
strength set to 5mA
“L” level maximum overall output current
ΣIOL1
-
100
mA Normal outputs
ΣIOLAV1
-
50
mA Normal outputs
IOH1
-
-15
mA
”H” level average output current
IOHAV1
-
-5
mA Normal outputs with driving
strength set to 5mA
”H” level maximum overall output current
ΣIOH1
-
-100
mA Normal outputs
”H” level average overall output current
ΣIOHAV1
-
-50
mA Normal outputs
-
430*5
mW TA=105oC
-
750*5
mW TA=90oC
-
540*5
mW
-
375*5
mW TA=105oC
-
750*5
mW TA=85oC
-
470*5
mW
TA=125oC, no Flash program/
erase *6
-
560*5
mW
TA=120oC, no Flash program/
erase *6
Maximum Clamp Current
Total Maximum Clamp Current
“L” level maximum output current
“L” level average overall output current
”H” level maximum output current
Permitted Power dissipation (Flash devices in QFP package) *4
Permitted Power dissipation
(MB96F346/F347/F348 in LQFP package) *4
FME-MB96340 rev 10
PD
PD
Normal outputs with driving
strength set to 5mA
TA=125oC, no Flash program/
erase *6
61
MB96340 Series
Parameter
Permitted Power dissipation (MB96F345
in LQFP package) *4
Permitted Power dissipation (Mask ROM
devices) *4
Operating ambient temperature
Storage temperature
Symbol
Rating
Unit
Max
-
335*5
mW TA=105oC
-
670*5
mW TA=85oC
-
840*5
mW TA=75oC
-
420*5
mW
TA=125oC, no Flash program/
erase *6
-
590*5
mW
TA=115oC, no Flash program/
erase *6
-
350
mW TA=105oC
-
360
mW TA=125oC *6
0
+70
-40
+105
-40
+125
-55
+150
PD
PD
TA
TSTG
Remarks
Min
MB96V300B
o
C
*6
o
C
*1: AVCC and VCC must be set to the same voltage. It is required that AVCC does not exceed VCC and that the voltage
at the analog inputs does not exceed AVCC neither when the power is switched on.
*2: VI and VO should not exceed VCC + 0.3 V. VI should also not exceed the specified ratings. However if the
maximum current to/from a input is limited by some means with external components, the ICLAMP rating supersedes the VI rating. Input/output voltages of standard ports depend on VCC.
*3: • Applicable to all general purpose I/O pins (Pnn_m)
• Use within recommended operating conditions.
• Use at DC voltage (current)
• The +B signal should always be applied a limiting resistance placed between the +B signal and the
microcontroller.
• The value of the limiting resistance should be set so that when the +B signal is applied the input current to
the microcontroller pin does not exceed rated values, either instantaneously or for prolonged periods.
• Note that when the microcontroller drive current is low, such as in the power saving modes, the +B input
potential may pass through the protective diode and increase the potential at the VCC pin, and this may affect
other devices.
• Note that if a +B signal is input when the microcontroller power supply is off (not fixed at 0 V), the power
supply is provided from the pins, so that incomplete operation may result.
• Note that if the +B input is applied during power-on, the power supply is provided from the pins and the resulting
supply voltage may not be sufficient to operate the Power reset (except devices with persistent low voltage
reset in internal vector mode).
62
FME-MB96340 rev 10
MB96340 Series
• Sample recommended circuits:
Protective Diode
VCC
Limiting
resistance
P-ch
+B input (0V to 16V)
N-ch
R
*4: The maximum permitted power dissipation depends on the ambient temperature, the air flow velocity and the
thermal conductance of the package on the PCB.
The actual power dissipation depends on the customer application and can be calculated as follows:
PD = PIO + PINT
PIO = ∑ (VOL * IOL + VOH * IOH) (IO load power dissipation, sum is performed on all IO ports)
PINT = VCC * (ICC + IA) (internal power dissipation)
ICC is the total core current consumption into VCC as described in the “DC characteristics” and depends on the
selected operation mode and clock frequency and the usage of functions like Flash programming or the clock
modulator.
IA is the analog current consumption into AVCC.
*5: Worst case value for a package mounted on single layer PCB at specified TA without air flow.
*6: Please contact Fujitsu for reliability limitations when using under these conditions.
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
FME-MB96340 rev 10
63
MB96340 Series
2. Recommended Operating Conditions
Parameter
Symbol
Value
Min
Typ
Max
Unit
Power supply voltage
VCC
3.0
-
5.5
V
Smoothing capacitor at C
pin
CS
3.5
4.7
15
µF
Remarks
Use a X7R ceramic capacitor or
a capacitor that has similar frequency characteristics
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representatives beforehand.
64
FME-MB96340 rev 10
MB96340 Series
3. DC characteristics
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Pin
Input H voltage
Condition
Unit
Remarks
Min
Typ
Max
0.8
VCC
-
VCC +
0.3
V
Not available in
MB96F345
0.7
VCC
-
VCC +
0.3
V
VCC ≥ 4.5V
0.74
VCC
-
VCC +
0.3
V
VCC < 4.5V
0.8
VCC
-
VCC +
0.3
V
TTL input selected
2.0
-
VCC +
0.3
V
Not available in
MB96F345
Not available in
MB96F34xY/R/AxA
CMOS Hysteresis
0.8/0.2 input selected
VIH
Value
CMOS Hysteresis
Port inputs 0.7/0.3 input selected
Pnn_m
AUTOMOTIVE
Hysteresis input
selected
VIHX0F
X0
External clock in
“Fast Clock Input
mode”
0.8
VCC
-
VCC +
0.3
V
VIHX0S
X0,X1,
X0A,X1A
External clock in
“oscillation mode”
2.5
-
VCC +
0.3
V
VIHR
RSTX
-
0.8
VCC
-
VCC +
0.3
V
VIHM
MD2-MD0
-
VCC 0.3
-
VCC +
0.3
V
CMOS Hysteresis
0.8/0.2 input selected
VSS 0.3
-
0.2
VCC
V
CMOS Hysteresis
0.7/0.3 input sePort inputs lected
VSS 0.3
-
0.3
VCC
V
VSS 0.3
-
0.5
VCC
V
VSS 0.3
-
0.46
VCC
TTL input selected
VSS 0.3
-
0.8
V
Not available in
MB96F345
Not available in
MB96F34xY/R/AxA
Input L voltage
VIL
Pnn_m
AUTOMOTIVE
Hysteresis input
selected
Not available in
MB96F345
VCC ≥ 4.5V
VCC < 4.5V
VILX0F
X0
External clock in
“Fast Clock Input
mode”
VSS 0.3
-
0.2 VCC
V
VILX0S
X0,X1,
X0A,X1A
External clock in
“oscillation mode”
VSS 0.3
-
0.4
V
VILR
RSTX
-
VSS 0.3
-
0.2 VCC
V
VILM
MD2-MD0
-
VSS 0.3
-
VSS +
0.3
V
FME-MB96340 rev 10
CMOS Hysteresis input
CMOS Hysteresis input
65
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Pin
Condition
Value
Unit
Remarks
Min
Typ
Max
VCC 0.5
-
-
V
Driving strength set
to 2mA
(PODR:OD=1)
VCC 0.5
-
-
V
Driving strength set
to 5mA
(PODR:OD=0)
VCC 0.5
-
-
V
I/O circuit type “N”
-
-
0.4
V
Driving strength set
to 2mA
(PODR:OD=1)
-
-
0.4
V
Driving strength set
to 5mA
(PODR:OD=0)
-
-
0.4
V
I/O circuit type “N”
AVSS, AVRL < VI <
AVCC, AVRH
-1
-
+1
µA Single port pin
VCC = 3.3V ± 10%
40
100
160
kΩ
VCC = 5.0V ± 10%
25
50
100
kΩ
4.5V ≤ VCC ≤ 5.5V
Output H voltage
VOH2
Normal
outputs
IOH = -2mA
3.0V ≤ VCC < 4.5V
IOH = -1.6mA
4.5V ≤ VCC ≤ 5.5V
VOH5
Normal
outputs
IOH = -5mA
3.0V ≤ VCC < 4.5V
IOH = -3mA
4.5V ≤ VCC ≤ 5.5V
VOH3
3mA outputs
IOH = -3mA
3.0V ≤ VCC < 4.5V
IOH = -2mA
4.5V ≤ VCC ≤ 5.5V
Output L voltage
VOL2
Normal
outputs
IOL = +2mA
3.0V ≤ VCC < 4.5V
IOL = +1.6mA
4.5V ≤ VCC ≤ 5.5V
VOL5
Normal
outputs
IOL = +5mA
3.0V ≤ VCC < 4.5V
IOL = +3mA
VOL3
3mA outputs
Input leak current
IIL
Pnn_m
Pull-up resistance
RUP
Pnn_m,
RSTX
3.0V ≤ VCC ≤ 5.5V
IOL = +3mA
VSS < VI < VCC
66
FME-MB96340 rev 10
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Value
Condition (at TA)
Typ
Max
+25˚C
8
11
+125˚C
8.5
13
Unit
Remarks
mA MB96345/346
PLL Run mode with
CLKS1/2 = CLKB =
CLKP1 = 16MHz,
CLKP2 = 8MHz
+25˚C
15
20
+125˚C
16
23
1 Flash/ROM wait state
+25˚C
17
22
(CLKRC and CLKSC
stopped)
mA MB96F345
mA
+125˚C
18.5
25.5
+25˚C
16
21
+125˚C
17.5
24.5
+25˚C
14
18
+125˚C
14.5
20
MB96F346/F347/F348Y/
R/Ayy
mA MB96F348T/H/CyB/C
mA MB96345/346
Power supply
current in Run
modes*
ICCPLL
PLL Run mode with
CLKS1/2 = CLKB =
CLKP1 = 32MHz,
CLKP2 = 16MHz
+25˚C
23.5
29.5
+125˚C
25
32.5
2 Flash/ROM wait states
+25˚C
26
32
(CLKRC and CLKSC
stopped)
mA MB96F345
mA
+125˚C
28
36
+25˚C
25
31
+125˚C
27
35
+25˚C
13
17
+125˚C
13.5
19
MB96F346/F347/F348Y/
R/Ayy
mA MB96F348T/H/CyB/C
mA MB96345/346
PLL Run mode with
CLKS1/2 = 48MHz,
CLKB = CLKP1/2 =
24MHz
+25˚C
27
39
+125˚C
29
42
0 Flash/ROM wait states
+25˚C
31
43
(CLKRC and CLKSC
stopped)
mA MB96F345
mA
+125˚C
33
47
+25˚C
30
42
+125˚C
32
46
MB96F346/F347/F348Y/
R/Ayy
mA MB96F348T/H/CyB/C
FME-MB96340 rev 10
67
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
PLL Run mode with
CLKS1/2 = CLKB =
CLKP1= 56MHz,
CLKP2 = 28MHz
2 Flash/ROM wait states
(CLKRC and CLKSC
stopped. Core voltage at
1.9V)
PLL Run mode with
CLKS1/2 = 72MHz,
CLKB = CLKP1 = 36MHz,
CLKP2 = 18MHz
1 Flash wait state
ICCPLL
Typ
Max
+25˚C
24
29
+125˚C
24.5
31
+25˚C
46
57
Unit
Remarks
mA MB96345/346
mA
+125˚C
48
61
+25˚C
44
55
+125˚C
46
59
+25˚C
38
51
MB96F346/F347/F348Y/
R/Ayy
mA MB96F348T/H/CyB/C
mA
+125˚C
40
55
+25˚C
38
51
+125˚C
40
54
+25˚C
24
28.5
+125˚C
24.5
30.5
1 Flash/ROM wait state
+25˚C
49
62
(CLKRC and CLKSC
stopped. Core voltage at
1.9V)
+125˚C
51
66
+25˚C
2.3
3.3
+125˚C
2.8
5.3
+25˚C
4
5
+125˚C
4.6
7.2
+25˚C
4.5
5.5
+125˚C
5.2
8.5
MB96F346/F347/F348Y/
R/Ayy
(CLKRC and CLKSC
stopped. Core voltage at
1.9V)
PLL Run mode with
CLKS1/2 = 80MHz,
CLKB = CLKP1 = 40MHz,
CLKP2 = 20MHz
Power supply
current in Run
modes*
Value
Condition (at TA)
1 Flash wait state
mA MB96F345
(CLKRC and CLKSC
stopped. Core voltage at
1.9V)
PLL Run mode with
CLKS1/2 = 96MHz,
CLKB = CLKP1= 48MHz,
CLKP2 = 24MHz
mA MB96345/346
mA MB96F348T/H/CyB/C
mA MB96345/346
Main Run mode with
CLKS1/2 = CLKB =
CLKP1/2 = 4MHz
ICCMAIN
1 Flash/ROM wait state
(CLKPLL, CLKSC and
CLKRC stopped)
mA MB96F345
mA MB96F346/F347/F348
68
FME-MB96340 rev 10
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Value
Condition (at TA)
Typ
Max
+25˚C
1.5
2.5
+125˚C
2
4.4
+25˚C
2.5
3.5
+125˚C
3.1
5.7
+25˚C
2.9
4
+125˚C
3.6
7
+25˚C
0.35
0.55
+125˚C
0.75
2.3
+25˚C
0.18
0.3
+125˚C
0.73
2.3
+25˚C
0.4
0.6
+125˚C
0.95
3.4
+25˚C
0.08
0.17
+125˚C
0.47
1.92
+25˚C
0.15
0.25
(CLKMC, CLKPLL and +125˚C
CLKSC stopped. Voltage
+25˚C
regulator in low power
mode, no Flash programming/erasing allowed)
+125˚C
0.7
2.25
0.15
0.25
0.7
3.05
+25˚C
0.04
0.12
+125˚C
0.43
1.85
+25˚C
0.1
0.2
(CLKMC, CLKPLL and +125˚C
CLKRC stopped, no Flash
programming/erasing al- +25˚C
lowed)
+125˚C
0.65
2.2
0.1
0.2
0.65
3
Unit
Remarks
mA MB96345/346
RC Run mode with
CLKS1/2 = CLKB =
CLKP1/2 = 2MHz
ICCRCH
1 Flash/ROM wait state
(CLKMC, CLKPLL and
CLKSC stopped)
mA MB96F345
mA MB96F346/F347/F348
RC Run mode with
CLKS1/2 = CLKB =
CLKP1/2 = 100kHz,
SMCR:LPMS = 0
mA MB96345/346
1 Flash/ROM wait state
Power supply
current in Run
modes*
(CLKMC, CLKPLL and
CLKSC stopped. Voltage
regulator in high power
mode)
mA MB96F345
mA MB96F346/F347/F348
ICCRCL
RC Run mode with
CLKS1/2 = CLKB =
CLKP1/2 = 100kHz,
SMCR:LPMS = 1
1 Flash/ROM wait state
Sub Run mode with
CLKS1/2 = CLKB =
CLKP1/2 = 32kHz
ICCSUB
FME-MB96340 rev 10
1 Flash/ROM wait state
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
69
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Value
Condition (at TA)
Typ
Max
+25˚C
4
6
+125˚C
4.5
8
+25˚C
4
6
+125˚C
4.7
8.5
+25˚C
4
6
Unit
Remarks
mA MB96345/346
PLL Sleep mode with
CLKS1/2 = CLKP1 =
16MHz,
CLKP2 = 8MHz
(CLKRC and CLKSC
stopped)
mA MB96F345
mA
+125˚C
4.7
9
+25˚C
4.7
6.7
+125˚C
5.5
9.7
+25˚C
7.5
10
+125˚C
8
12
+25˚C
7
9.5
+125˚C
7.7
12
+25˚C
7.5
10
MB96F346/F347/F348Y/
R/Ayy
mA MB96F348T/H/CyB/C
mA MB96345/346
Power supply
current in Sleep
modes*
ICCSPLL
PLL Sleep mode with
CLKS1/2 = CLKP1 =
32MHz,
CLKP2 = 16MHz
(CLKRC and CLKSC
stopped)
mA MB96F345
mA
+125˚C
8.4
13
+25˚C
8.5
11
+125˚C
9.5
14
+25˚C
7.5
9.5
+125˚C
8
11.5
+25˚C
7
9
+125˚C
7.7
11.5
+25˚C
7.5
9.5
MB96F346/F347/F348Y/
R/Ayy
mA MB96F348T/H/CyB/C
mA MB96345/346
PLL Sleep mode with
CLKS1/2 = 48MHz,
CLKP1/2 = 24MHz
(CLKRC and CLKSC
stopped)
mA MB96F345
mA
+125˚C
8.4
12.5
+25˚C
8.5
10.5
+125˚C
9.5
13.5
MB96F346/F347/F348Y/
R/Ayy
mA MB96F348T/H/CyB/C
70
FME-MB96340 rev 10
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Value
Condition (at TA)
Typ
Max
+25˚C
12.5
16
PLL Sleep mode with
CLKS1/2 = CLKP1=
56MHz, CLKP2 = 28MHz
+125˚C
13
18
+25˚C
12.5
16
(CLKRC and CLKSC
stopped. Core voltage at
1.9V)
+125˚C
13.5
19
+25˚C
13.5
17
+125˚C
14.5
20
PLL Sleep mode with
CLKS1/2 = 72MHz,
CLKP1 = 36MHz,
CLKP2 = 18MHz
+25˚C
9.5
12.5
(CLKRC and CLKSC
stopped. Core voltage at
1.9V)
+125˚C
10.5
15.5
PLL Sleep mode with
CLKS1/2 = 80MHz,
CLKP1 = 40MHz,
CLKP2 = 20MHz
+25˚C
11
13.5
(CLKRC and CLKSC
stopped. Core voltage at
1.9V)
+125˚C
11.7
16
PLL Sleep mode with
CLKS1/2 = 96MHz,
CLKP1= 48MHz,
CLKP2 = 24MHz
+25˚C
13
16
+125˚C
13.5
18
+25˚C
15
18
+125˚C
16
21
+25˚C
1.3
1.8
+125˚C
1.8
3.7
+25˚C
1
1.3
+125˚C
1.6
3.4
+25˚C
1.3
1.8
+125˚C
1.9
4.6
Unit
Remarks
mA MB96345/346
mA
MB96F346/F347/F348Y/
R/Ayy
mA MB96F348T/H/CyB/C
ICCSPLL
Power supply
current in Sleep
modes*
(CLKRC and CLKSC
stopped. Core voltage at
1.9V)
mA
MB96F346/F347/F348Y/
R/Ayy
mA MB96F345
mA MB96345/346
mA MB96F348T/H/CyB/C
mA MB96345/346
ICCSMAIN
Main Sleep mode with
CLKS1/2 = CLKP1/2 =
4MHz
(CLKPLL, CLKSC and
CLKRC stopped)
mA MB96F345
mA MB96F346/F347/F348
FME-MB96340 rev 10
71
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Value
Condition (at TA)
Typ
Max
+25˚C
0.8
1.4
+125˚C
1.3
3.2
+25˚C
0.55
1.1
+125˚C
1.1
3.1
+25˚C
0.8
1.4
+125˚C
1.4
4.2
+25˚C
0.3
0.5
+125˚C
0.7
2.3
+25˚C
0.09
0.2
+125˚C
0.59
2.2
+25˚C
0.3
0.5
+125˚C
0.8
3.3
+25˚C
0.05
0.14
+125˚C
0.44
1.9
+25˚C
0.05
0.15
+125˚C
0.56
2.1
+25˚C
0.05
0.15
+125˚C
0.56
2.9
+25˚C
0.04
0.12
+125˚C
0.43
1.85
+25˚C
0.04
0.12
+125˚C
0.54
2.1
+25˚C
0.04
0.12
+125˚C
0.54
2.9
Unit
Remarks
mA MB96345/346
ICCSRCH
RC Sleep mode with
CLKS1/2 = CLKP1/2 =
2MHz
(CLKMC, CLKPLL and
CLKSC stopped)
mA MB96F345
mA MB96F346/F347/F348
RC Sleep mode with
CLKS1/2 = CLKP1/2 =
100kHz,
SMCR:LPMSS = 0
(CLKMC, CLKPLL and
CLKSC stopped. Voltage
regulator in high power
mode)
Power supply
current in Sleep
modes*
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
ICCSRCL
RC Sleep mode with
CLKS1/2 = CLKP1/2 =
100kHz,
SMCR:LPMSS = 1
(CLKMC, CLKPLL and
CLKSC stopped. Voltage
regulator in low power
mode)
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
mA MB96345/346
ICCSSUB
Sub Sleep mode with
CLKS1/2 = CLKP1/2 =
32kHz
(CLKMC, CLKPLL and
CLKRC stopped)
mA MB96F345
mA MB96F346/F347/F348
72
FME-MB96340 rev 10
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Value
Condition (at TA)
Typ
Max
+25˚C
1.4
1.9
+125˚C
1.9
3.9
+25˚C
1.3
1.8
+125˚C
1.9
4
+25˚C
1.5
2
+125˚C
2.1
5
+25˚C
0.35
0.5
+125˚C
0.7
2.3
+25˚C
0.11
0.2
+125˚C
0.63
2.2
+25˚C
0.35
0.5
+125˚C
0.85
3.3
+25˚C
0.08
0.15
+125˚C
0.47
1.9
+25˚C
0.08
0.15
+125˚C
0.6
2.1
+25˚C
0.08
0.15
+125˚C
0.6
2.9
Unit
Remarks
mA MB96345/346
ICCTPLL
PLL Timer mode with
CLKMC = 4MHz, CLKPLL
= 48MHz
(CLKRC and CLKSC
stopped)
mA MB96F345
mA MB96F346/F347/F348
Main Timer mode with
CLKMC = 4MHz,
SMCR:LPMSS = 0
Power supply
current in Timer
modes*
(CLKPLL, CLKRC and
CLKSC stopped. Voltage
regulator in high power
mode)
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
ICCTMAIN
Main Timer mode with
CLKMC = 4MHz,
SMCR:LPMSS = 1
(CLKPLL, CLKRC and
CLKSC stopped. Voltage
regulator in low power
mode)
FME-MB96340 rev 10
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
73
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Value
Condition (at TA)
RC Timer mode with
CLKRC = 2MHz,
SMCR:LPMSS = 0
(CLKMC, CLKPLL and
CLKSC stopped. Voltage
regulator in high power
mode)
Typ
Max
+25˚C
0.35
0.5
+125˚C
0.7
2.3
+25˚C
0.13
0.2
+125˚C
0.63
2.2
+25˚C
0.35
0.5
+125˚C
0.85
3.3
+25˚C
0.07
0.15
+125˚C
0.46
1.9
+25˚C
0.07
0.15
+125˚C
0.6
2.1
+25˚C
0.07
0.15
+125˚C
0.6
2.9
+25˚C
0.3
0.45
+125˚C
0.65
2.2
+25˚C
0.08
0.15
+125˚C
0.58
2.1
+25˚C
0.3
0.45
+125˚C
0.8
3.2
+25˚C
0.03
0.1
+125˚C
0.41
1.85
+25˚C
0.03
0.1
+125˚C
0.53
2.05
+25˚C
0.03
0.1
+125˚C
0.53
2.85
Unit
Remarks
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
ICCTRCH
RC Timer mode with
CLKRC = 2MHz,
SMCR:LPMSS = 1
(CLKMC, CLKPLL and
CLKSC stopped. Voltage
regulator in low power
mode)
Power supply
current in Timer
modes*
RC Timer mode with
CLKRC = 100kHz,
SMCR:LPMSS = 0
(CLKMC, CLKPLL and
CLKSC stopped. Voltage
regulator in high power
mode)
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
ICCTRCL
RC Timer mode with
CLKRC = 100kHz,
SMCR:LPMSS = 1
(CLKMC, CLKPLL and
CLKSC stopped. Voltage
regulator in low power
mode)
74
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
FME-MB96340 rev 10
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Value
Condition (at TA)
Unit
Remarks
Typ
Max
+25˚C
0.035
0.1
+125˚C
0.42
1.85
Sub Timer mode with
CLKSC = 32kHz
+25˚C
0.035
0.1
(CLKMC, CLKPLL and
CLKRC stopped)
+125˚C
0.53
2.05
+25˚C
0.035
0.1
+125˚C
0.53
2.85
+25˚C
0.02
0.08
+125˚C
0.4
1.8
VRCR:LPMB[2:0] = 110B
+25˚C
0.02
0.08
(Core voltage at 1.8V)
+125˚C
0.52
2.0
+25˚C
0.02
0.08
+125˚C
0.52
2.8
+25˚C
0.015
0.06
+125˚C
0.3
1.4
VRCR:LPMB[2:0] = 000B
+25˚C
0.015
0.06
(Core voltage at 1.2V)
+125˚C
0.4
1.5
+25˚C
0.015
0.06
+125˚C
0.4
2.3
+25˚C
5
10
µA
MB96F345
+125˚C
7
20
µA
Must be added to all current above
+25˚C
90
140
+125˚C
100
150
mA MB96345/346
Power supply
current in Timer
modes*
ICCTSUB
mA MB96F345
mA MB96F346/F347/F348
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
Power supply
current in Stop
Mode
ICCH
mA MB96345/346
mA MB96F345
mA MB96F346/F347/F348
Power supply
current for active
Low Voltage detector
ICCLVD
Low voltage detector enabled (RCR:LVDE = 1)
Other devices
µA
Power supply
current for active
Clock modulator
Flash Write/
Erase current
Must be added to all current above
ICCCLOMO
Clock modulator enabled
(CMCR:PDX = 1)
-
3
4.5
mA
Must be added to all current above
ICCFLASH
Current for one Flash
module
-
15
40
mA
Must be added to all current above
ICCDFLASH
Current for one Data Flash
module
10
20
mA
Must be added to all current above
FME-MB96340 rev 10
75
MB96340 Series
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Input capacitance
Symbol
CIN
Value
Condition (at TA)
-
-
Typ
Max
Unit
5
15
pF
Remarks
Other than C, AVCC, AVSS,
AVRH, AVRL, VCC, VSS
* The power supply current is measured with a 4MHz external clock connected to the Main oscillator and a 32kHz
external clock connected to the Sub oscillator. See chapter “Standby mode and voltage regulator control circuit” of
the Hardware Manual for further details about voltage regulator control.
76
FME-MB96340 rev 10
MB96340 Series
4. AC Characteristics
Source Clock timing
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Clock frequency
fC
Pin
X0, X1
Value
fFCI
Max
3
-
16
MHz When using a crystal oscillator, PLL off
0
-
16
MHz
When using an opposite phase external
clock, PLL off
3.5
-
16
MHz
When using a crystal oscillator or opposite phase external clock, PLL on
56
When using a single phase external
clock in “Fast Clock Input mode” (not
MHz
available in MB96F34xY/R/AxA), PLL
off
fCL
X0A
Clock frequency
fCR
-
X0
X0A, X1A
Clock frequency
Remarks
Typ
0
Clock frequency
Unit
Min
3.5
-
56
When using a single phase external
clock in “Fast Clock Input mode” (not
MHz
available in MB96F34xY/R/AxA), PLL
on
32
32.768
100
kHz When using an oscillation circuit
0
-
100
kHz
When using an opposite phase external
clock
0
-
50
kHz
When using a single phase external
clock
50
100
200
kHz
When using slow frequency of RC oscillator
1
2
4
MHz
When using fast frequency of RC oscillator
-
RC clock stabilization time
tRCSTAB
-
64 or 256 RC clock cycles
Applied after any reset and when activating the RC oscillator.
MB96F345: 256 cycles
others 64 cycles
PLL Clock frequency
fCLKVCO
-
64
-
200
MHz
Permitted VCO output frequency of PLL
(CLKVCO)
PLL Phase Jitter
TPSKEW
-
-
-
± 5
ns
For CLKMC (PLL input clock) ≥ 4MHz,
jitter coming from external oscillator,
crystal or resonator is not covered
Input clock pulse
width
PWH, PWL
X0,X1
8
-
-
ns
Duty ratio is about 30% to 70%
5
-
-
µs
Input clock pulse
width
PWHL, PWLL X0A,X1A
FME-MB96340 rev 10
77
MB96340 Series
tCYL
VIH
X0
VIL
PWH
PWL
tCYLL
VIH
X0A
VIL
PWHL
78
PWLL
FME-MB96340 rev 10
MB96340 Series
Internal Clock timing
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Core Voltage Settings
Parameter
Internal System clock frequency (CLKS1 and
CLKS2)
Internal CPU clock frequency (CLKB), internal
peripheral clock frequency
(CLKP1)
Internal peripheral clock
frequency (CLKP2)
FME-MB96340 rev 10
Symbol
fCLKS1, fCLKS2
fCLKB, fCLKP1
fCLKP2
1.8V
1.9V
Unit
Remarks
Others than below
Min
Max
Min
Max
0
92
0
96
MHz
0
86
0
96
MHz MB96F348T/H/CxB/C
0
72
0
80
MHz
MB96F345
0
68
0
74
MHz
MB96F34xY/R/Axx
0
52
0
56
MHz
Others than below
0
36
0
40
MHz
MB96F345
0
28
0
32
MHz
Others than below
0
26
0
28
MHz
MB96F34xY/R/Axx
79
MB96340 Series
External Reset timing
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Reset input time
Symbol
Pin
tRSTL
RSTX
Value
Min
Typ
Max
500
-
-
Unit
Remarks
ns
tRSTL
RSTX
0.2 VCC
80
0.2 VCC
FME-MB96340 rev 10
MB96340 Series
Power On Reset timing
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Power on rise time
Power off time
Symbol
Pin
tR
tOFF
Value
Unit
Min
Typ
Max
Vcc
0.05
-
30
ms
Vcc
1
-
-
ms
Remarks
tR
2.7V
VCC
0.2 V
0.2 V
0.2 V
tOFF
If the power supply is changed too rapidly, a power-on reset may occur.
We recommend a smooth startup by restraining voltages when changing the
power supply voltage during operation, as shown in the figure below.
VCC
3V
FME-MB96340 rev 10
Rising edge of 50 mV/ms
maximum is allowed
81
MB96340 Series
External Input timing
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter Symbol
Pin
Value
Condition
INTn(_R)
NMI(_R)
Input pulse
width
tINH
tINL
Min
Max
200
⎯
Unit
Used Pin input function
External Interrupt
ns
NMI
Pnn_m
General Purpose IO
TINn(_R)
Reload Timer
TTGn(_R)
⎯
2*tCLKP1 + 200
(tCLKP1=1/
fCLKP1)
ADTG(_R)
PPG Trigger input
⎯
ns
AD Converter Trigger
FRCKn(_R)
Free Running Timer
external clock
INn(_R)
Input Capture
Note : Relocated Resource Inputs have same characteristics
External Pin input
VIH
VIH
tINH
82
VIL
VIL
tINL
FME-MB96340 rev 10
MB96340 Series
External Bus timing
Note: The values given below are for an I/O driving strength IOdrive = 5mA. If IOdrive is 2mA, all the maximum output
timing described in the different tables must then be increased by 10ns.
Basic Timing
Parameter
(TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Symbol
Pin
Condition
Min
Max
25
⎯
tCYC/2-5
tCYC/2+5
tCLCH
tCYC/2-5
tCYC/2+5
tCHCBH
-20
20
-20
20
-20
20
tCLCBL
-20
20
tCHLH
-10
10
-10
10
-10
10
-10
10
-15
15
-15
15
-15
15
-15
15
-10
10
-10
10
-10
10
-10
10
tCYC
ECLK
ECLK →
UBX/ LBX / CSn time
ECLK → ALE time
tCHCL
tCHCBL
tCLCBH
tCHLL
tCLLH
ECLK
CSn, UBX,
LBX, ECLK
ALE, ECLK
⎯
⎯
⎯
tCLLL
tCHAV
ECLK → address valid time
tCLAV
tCLADV
tCHADV
A[23:16],
ECLK
⎯
AD[15:0],
ECLK
⎯
tCHRWH
ECLK → RDX /WRX time
tCHRWL
tCLRWH
tCLRWL
FME-MB96340 rev 10
Value
RDX, WRX,
WRLX,WRHX,
ECLK
⎯
Unit
Remarks
ns
ns
ns
ns
ns
ns
83
MB96340 Series
(TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Parameter
Symbol
Pin
Condition
Min
Max
30
⎯
tCYC/2-8
tCYC/2+8
tCLCH
tCYC/2-8
tCYC/2+8
tCHCBH
-25
25
-25
25
-25
25
tCLCBL
-25
25
tCHLH
-15
15
-15
15
-15
15
-15
15
-20
20
-20
20
-20
20
-20
20
-15
15
-15
15
-15
15
-15
15
tCYC
ECLK
ECLK →
UBX/ LBX / CSn time
ECLK → ALE time
tCHCL
tCHCBL
tCLCBH
tCHLL
tCLLH
ECLK
CSn, UBX,
LBX, ECLK
ALE, ECLK
⎯
⎯
⎯
tCLLL
tCHAV
ECLK → address valid time
tCLAV
tCLADV
tCHADV
A[23:16],
ECLK
⎯
AD[15:0],
ECLK
⎯
tCHRWH
ECLK → RDX /WRX time
tCHRWL
tCLRWH
tCLRWL
84
Value
RDX, WRX,
WRLX, WRHX,
ECLK
⎯
Unit
Remarks
ns
ns
ns
ns
ns
ns
FME-MB96340 rev 10
MB96340 Series
tCYC
tCHCL
ECLK
tCLCH
0.8*Vcc
0.2*Vcc
tCLAV
tCHAV
A[23:16]
tCHCBL
tCLCBH
tCLCBL
tCHCBH
tCHRWL
tCLRWH
tCLRWL
tCHRWH
CSn
LBX
UBX
RDX
WRX (WRLX, WRHX)
tCLLH
tCHLL
tCHLH
tCLLL
ALE
tCHADV
tCLADV
AD[15:0]
Address
Refer to the Hardware Manual for detailed Timing Charts
FME-MB96340 rev 10
85
MB96340 Series
Bus Timing (Read)
Parameter
(TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Symbol
Pin
Conditions
Min
Max
tCYC/2 − 5
⎯
tCYC − 5
⎯
EACL:STS=0 and
EACL:ACE=1
3tCYC/2 − 5
⎯
EACL:STS=0 and
EACL:ACE=0
tCYC − 15
⎯
EACL:STS=0 and
EACL:ACE=0
ALE pulse width
tLHLL ALE
tAVLL ALE, A[23:16],
Valid address
⇒ ALE ↓ time
tADVLL ALE,AD[15:0]
ALE ↓
⇒ Address valid time
tLLAX ALE, AD[15:0]
tAVRL
RDX, A[23:16]
Valid address
⇒ RDX ↓ time
tADVRL RDX, AD[15:0]
tAVDV
Valid address
⇒ Valid data input
A[23:16],
AD[15:0]
tADVDV AD[15:0]
Value
EACL:STS=1
EACL:STS=1 and
3tCYC/2 − 15
EACL:ACE=0
⎯
EACL:STS=0 and
EACL:ACE=1
⎯
2tCYC − 15
⎯
EACL:STS=0 and
EACL:ACE=0
tCYC/2 − 15
⎯
EACL:STS=1 and
EACL:ACE=0
tCYC − 15
⎯
ns
ns
EACL:STS=0 and
3tCYC/2 − 15
EACL:ACE=1
⎯
EACL:STS=1 and
EACL:ACE=1
2tCYC − 15
⎯
EACL:STS=0
tCYC/2 − 15
⎯
EACL:STS=1
-15
⎯
EACL:ACE=0
3tCYC/2 − 15
⎯
ns
ns
EACL:ACE=1
5tCYC/2 − 15
⎯
EACL:ACE=0
tCYC − 15
⎯
ns
EACL:ACE=1
2tCYC − 15
⎯
EACL:ACE=0
⎯
3tCYC − 55
ns
w/o cycle
extension
ns
w/o cycle
extension
ns
w/o cycle
extension
3 tCYC/2 − 50 ns
w/o cycle
extension
EACL:ACE=1
⎯
4tCYC − 55
EACL:ACE=0
⎯
5tCYC/2 − 55
⎯
7tCYC/2 − 55
⎯
RDX pulse width
tRLRH RDX
⎯
3 tCYC/2 − 5
RDX ↓ ⇒ Valid data input
tRLDV RDX, AD[15:0]
⎯
⎯
RDX ↑ ⇒ Data hold time
tRHDX RDX, AD[15:0]
⎯
0
86
Remarks
ns
EACL:STS=1 and
5tCYC/2 − 15
EACL:ACE=1
EACL:ACE=1
Unit
⎯
ns
FME-MB96340 rev 10
MB96340 Series
(TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Parameter
Symbol
Address valid ⇒ Data hold
time
tAXDX
Pin
A[23:16],
AD[15:0]
RDX ↑ ⇒ ALE ↑ time
tRHLH RDX, ALE
Valid address
⇒ ECLK ↑ time
tAVCH A[23:16], ECLK
tADVCH AD[15:0], ECLK
RDX ↓ ⇒ ECLK ↑ time
tRLCH RDX, ECLK
ALE ↓ ⇒ RDX ↓ time
tLLRL ALE, RDX
ECLK↑ ⇒ Valid data input
tCHDV AD[15:0], ECLK
Conditions
⎯
Value
Min
Max
0
⎯
EACL:STS=1 and
3tCYC/2 − 10
EACL:ACE=1
⎯
other ECL:STS,
tCYC/2 − 10
EACL:ACE setting
⎯
⎯
tCYC/2 − 15
⎯
tCYC/2 − 10
⎯
EACL:STS=0
tCYC/2 − 10
⎯
EACL:STS=1
− 10
⎯
⎯
tCYC − 50
⎯
⎯
Remarks
ns
ns
tCYC − 15
⎯
Unit
ns
ns
ns
ns
(TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Parameter
Symbol
Pin
Conditions
Min
Max
tCYC/2 − 8
⎯
tCYC − 8
⎯
EACL:STS=0 and
EACL:ACE=1
3tCYC/2 − 8
⎯
EACL:STS=0 and
EACL:ACE=0
tCYC − 20
⎯
EACL:STS=0 and
EACL:ACE=0
ALE pulse width
tLHLL ALE
tAVLL ALE, A[23:16],
Valid address
⇒ ALE ↓ time
tADVLL ALE, AD[15:0]
ALE ↓
⇒ Address valid time
FME-MB96340 rev 10
tLLAX ALE, AD[15:0]
Value
EACL:STS=1
EACL:STS=1 and
3tCYC/2 − 20
EACL:ACE=0
⎯
EACL:STS=0 and
EACL:ACE=1
⎯
2tCYC − 20
Unit
Remarks
ns
ns
EACL:STS=1 and
5tCYC/2 − 20
EACL:ACE=1
⎯
EACL:STS=0 and
EACL:ACE=0
tCYC/2 − 20
⎯
EACL:STS=1 and
EACL:ACE=0
tCYC − 20
⎯
ns
EACL:STS=0 and
3tCYC/2 − 20
EACL:ACE=1
⎯
EACL:STS=1 and
EACL:ACE=1
2tCYC − 20
⎯
EACL:STS=0
tCYC/2 − 20
⎯
EACL:STS=1
-20
⎯
ns
87
MB96340 Series
(TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Parameter
Symbol
tAVRL
Pin
RDX, A[23:16]
Valid address
⇒ RDX ↓ time
tADVRL RDX, AD[15:0]
tAVDV
Valid address
⇒ Valid data input
A[23:16],
AD[15:0]
tADVDV AD[15:0]
Conditions
Value
Min
Max
EACL:ACE=0
3tCYC/2 − 20
⎯
EACL:ACE=1
5tCYC/2 − 20
⎯
EACL:ACE=0
tCYC − 20
⎯
EACL:ACE=1
2tCYC − 20
⎯
EACL:ACE=0
⎯
3tCYC − 60
ns
ns
w/o cycle
extension
ns
w/o cycle
extension
ns
w/o cycle
extension
3tCYC/2 − 55 ns
w/o cycle
extension
⎯
4tCYC − 60
EACL:ACE=0
⎯
5tCYC/2 − 60
⎯
7tCYC/2 − 60
⎯
RDX pulse width
tRLRH RDX
⎯
3tCYC/2 − 8
RDX ↓ ⇒ Valid data input
tRLDV RDX, AD[15:0]
⎯
⎯
RDX ↑ ⇒ Data hold time
tRHDX RDX, AD[15:0]
⎯
0
⎯
ns
Address valid ⇒ Data hold
time
tAXDX A[23:16]
⎯
0
⎯
ns
RDX ↑ ⇒ ALE ↑ time
tRHLH RDX, ALE
Valid address
⇒ ECLK ↑ time
tAVCH A[23:16], ECLK
tADVCH AD[15:0], ECLK
RDX ↓ ⇒ ECLK ↑ time
tRLCH RDX, ECLK
ALE ↓ ⇒ RDX ↓ time
tLLRL ALE, RDX
ECLK↑ ⇒ Valid data input
tCHDV AD[15:0], ECLK
88
EACL:STS=1 and
3tCYC/2 − 15
EACL:ACE=1
⎯
other ECL:STS,
tCYC/2 − 15
EACL:ACE setting
⎯
ns
tCYC − 20
⎯
tCYC/2 − 20
⎯
tCYC/2 − 15
⎯
EACL:STS=0
tCYC/2 − 15
⎯
EACL:STS=1
− 15
⎯
⎯
tCYC − 55
⎯
⎯
⎯
Remarks
ns
EACL:ACE=1
EACL:ACE=1
Unit
ns
ns
ns
ns
FME-MB96340 rev 10
MB96340 Series
tAVCH
tRLCH
tADVCH
tCHDV
0.8*Vcc
ECLK
tAVLL
tLLAX
tADVLL
ALE
tRHLH
0.2*VCC
tLHLL
tAVRL
tADVRL
tRLRH
RDX
tLLRL
A[23:16]
tRLDV
tAXDX
tAVDV
tRHDX
tADVDV
AD[15:0]
VIH
VIH
Address
Read data
VIL
VIL
Refer to the Hardware Manual for detailed Timing Charts
.
Bus Timing (Write)
Parameter
(TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Symbol
tAVWL
Valid address
⇒ WRX ↓ time
tADVWL
Pin
WRX, WRLX,
WRHX,
A[23:16]
WRX, WRLX,
WRHX,
AD[15:0]
Condition
Value
Min
Max
EACL:ACE=0
3tCYC/2 −
15
⎯
EACL:ACE=1
5tCYC/2 −
15
⎯
EACL:ACE=0
tCYC − 15
⎯
EACL:ACE=1
Unit
Remarks
ns
ns
2tCYC − 15
⎯
WRX pulse width
tWLWH
WRX, WRXL,
WRHX
⎯
tCYC − 5
⎯
ns
w/o cycle
extension
Valid data output
⇒ WRX ↑ time
tDVWH
WRX, WRLX,
WRHX,
AD[15:0]
⎯
tCYC − 20
⎯
ns
w/o cycle
extension
FME-MB96340 rev 10
89
MB96340 Series
(TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Parameter
WRX ↑
⇒ Data hold time
WRX ↑
⇒ Address valid time
WRX ↑ ⇒ ALE ↑ time
WRX ↓ ⇒ ECLK ↑
time
Symbol
Pin
Condition
WRX ⇒ CSn time
Unit
Min
Max
tCYC/2 − 15
⎯
ns
tCYC/2 − 15
⎯
ns
2tCYC − 10
⎯
tWHLH
WRX, WRLX,
WRHX, ALE
EBM:ACE=1 and
EACL:STS=1
other EBM:ACE
and
EACL:STS setting
tCYC − 10
⎯
tWLCH
WRX, WRLX,
WRHX, ECLK
⎯
tCYC/2 − 10
⎯
⎯
3tCYC/2 −
15
⎯
5tCYC/2 −
15
tCYC/2 − 15
⎯
tWHDX
WRX, WRLX,
WRHX,
AD[15:0]
tWHAX
WRX, WRLX,
WRHX,
A[23:16]
⎯
⎯
EACL:ACE=0
CSn ⇒ WRX time
Value
WRX, WRLX,
WRHX, CSn
tCSLWL
WRX, WRLX,
WRHX, CSn
tWHCSH
EACL:ACE=1
⎯
Remarks
ns
ns
ns
ns
(TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Parameter
Symbol
tAVWL
Valid address
⇒ WRX ↓ time
tADVWL
Pin
WRX, WRLX,
WRHX,
A[23:16]
WRX, WRLX,
WRHX,
AD[15:0]
Condition
Value
Min
Max
EACL:ACE=0
3tCYC/2 −
20
⎯
EACL:ACE=1
5tCYC/2 −
20
⎯
EACL:ACE=0
tCYC − 20
⎯
EACL:ACE=1
Unit
Remarks
ns
ns
2tCYC − 20
⎯
WRX pulse width
tWLWH
WRX, WRXL,
WRHX
⎯
tCYC − 8
⎯
ns
w/o cycle
extension
Valid data output
⇒ WRX ↑ time
tDVWH
WRX, WRLX,
WRHX,
AD[15:0]
⎯
tCYC − 25
⎯
ns
w/o cycle
extension
WRX ↑
⇒ Data hold time
tWHDX
WRX, WRLX,
WRHX,
AD[15:0]
⎯
tCYC/2 − 20
⎯
ns
tWHAX
WRX, WRLX,
WRHX,
A[23:16]
tCYC/2 − 20
⎯
ns
WRX ↑
⇒ Address valid time
90
⎯
FME-MB96340 rev 10
MB96340 Series
(TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Parameter
WRX ↑ ⇒ ALE ↑ time
WRX ↓ ⇒ ECLK ↑
time
CSn ⇒ WRX time
WRX ⇒ CSn time
Symbol
Pin
Condition
Value
Min
Max
2tCYC − 15
⎯
tWHLH
WRX, WRLX,
WRHX, ALE
EBM:ACE=1 and
EACL:STS=1
other EBM:ACE
and
EACL:STS setting
tCYC − 15
⎯
tWLCH
WRX, WRLX,
WRHX, ECLK
⎯
tCYC/2 − 15
⎯
EACL:ACE=0
⎯
3tCYC/2 −
20
EACL:ACE=1
⎯
5tCYC/2 −
20
tCYC/2 − 20
⎯
tCSLWL
tWHCSH
WRX, WRLX,
WRHX, CSn
WRX, WRLX,
WRHX, CSn
⎯
Unit
Remarks
ns
ns
ns
ns
tWLCH
0.8*VCC
ECLK
tWHLH
ALE
.
tAVWL
tADVWL
WRX (WRLX, WRHX)
tWLWH
0.2*VCC
tCSLWL
tWHCSH
CSn
tWHAX
A[23:16]
tDVWH
AD[15:0]
Address
tWHDX
Write data
Refer to the Hardware Manual for detailed Timing Charts
FME-MB96340 rev 10
91
MB96340 Series
Ready Input Timing
Parameter
(TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Symbol
Pin
RDY setup time
tRYHS
RDY
RDY hold time
tRYHH
RDY
Rated Value
Test
Condition
⎯
Units
Min
Max
35
⎯
ns
0
⎯
ns
Remarks
(TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Parameter
Symbol
Pin
RDY setup time
tRYHS
RDY
RDY hold time
tRYHH
RDY
Rated Value
Test
Condition
⎯
Units
Min
Max
45
⎯
ns
0
⎯
ns
Remarks
Note : If the RDY setup time is insufficient, use the auto-ready function.
0.8*VCC
ECLK
RDY
When WAIT is not used.
RDY
When WAIT is used.
tRYHS
tRYHH
VIH
VIH
VIL
Refer to the Hardware Manual for detailed Timing Charts
Hold Timing
(TA = −40 °C to +125 °C, VCC = 5.0 V ± 10%, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Parameter
Symbol
Pin
Pin floating ⇒ HAKX ↓ time
tXHAL
HAKX
HAKX ↑ time ⇒ Pin valid time
tHAHV
HAKX
Condition
⎯
Value
Min
Units
Max
tCYC − 20 tCYC + 20
ns
tCYC − 20 tCYC + 20
ns
Remarks
(TA = −40 °C to +125 °C, VCC = 3.0 to 4.5V, VSS = 0.0 V, IOdrive = 5mA, CL = 50pF)
Parameter
Symbol
Pin
Pin floating ⇒ HAKX ↓ time
tXHAL
HAKX
HAKX ↑ time ⇒ Pin valid time
tHAHV
HAKX
92
Condition
⎯
Value
Min
Units
Max
tCYC − 25 tCYC + 25
ns
tCYC − 25 tCYC + 25
ns
Remarks
FME-MB96340 rev 10
MB96340 Series
0.8*VCC
HAKX
0.2*VCC
tHAHV
tXHAL
Each pin
0.8*VCC
High-Z
0.2*VCC
Refer to the Hardware Manual for detailed Timing Charts
FME-MB96340 rev 10
93
MB96340 Series
USART timing
WARNING: The values given below are for an I/O driving strength IOdrive = 5mA. If IOdrive is 2mA, all the maximum
output timing described in the different tables must then be increased by 10ns.
(TA = -40˚C to 125˚C, VCC = 3.0V to 5.5V, VSS = AVSS = 0V, IOdrive = 5mA, CL = 50pF)
Parameter
Condition
VCC = AVCC= 4.5V VCC = AVCC= 3.0V
to 5.5V
to 4.5V
Unit
Min
Max
Min
Max
Symbol
Pin
Serial clock cycle time
tSCYCI
SCKn
4 tCLKP1
⎯
4 tCLKP1
⎯
ns
SCK ↓ → SOT delay
time
tSLOVI
SCKn,
SOTn
-20
+20
-30
+30
ns
SOT → SCK ↑ delay
time
tOVSHI
SCKn,
SOTn
N*tCLKP1
- 20 *1
⎯
N*tCLKP1 30 *1
⎯
ns
Valid SIN → SCK ↑
tIVSHI
SCKn,
SINn
tCLKP1 +
45
⎯
tCLKP1 +
55
⎯
ns
SCK ↑ → Valid SIN
hold time
tSHIXI
SCKn,
SINn
0
⎯
0
⎯
ns
Serial clock “L” pulse
width
tSLSHE
SCKn
tCLKP1 +
10
⎯
tCLKP1 +
10
⎯
ns
Serial clock “H” pulse
width
tSHSLE
SCKn
tCLKP1 +
10
⎯
tCLKP1 +
10
⎯
ns
SCK ↓ → SOT delay
time
tSLOVE
SCKn,
SOTn
⎯
2 tCLKP1
+ 45
⎯
2 tCLKP1
+ 55
ns
Valid SIN → SCK ↑
tIVSHE
SCKn,
SINn
tCLKP1/2
+ 10
⎯
tCLKP1/2 +
10
⎯
ns
SCK ↑ → Valid SIN
hold time
tSHIXE
SCKn,
SINn
tCLKP1 +
10
⎯
tCLKP1 +
10
⎯
ns
SCK fall time
tFE
SCKn
⎯
20
⎯
20
ns
SCK rise time
tRE
SCKn
⎯
20
⎯
20
ns
Internal Shift
Clock Mode
External Shift
Clock Mode
Notes: • AC characteristic in CLK synchronized mode.
• CL is the load capacity value of pins when testing.
• Depending on the used machine clock frequency, the maximum possible baud rate can be limited by some
parameters. These parameters are shown in “MB96300 Super series HARDWARE MANUAL”
• tCLKP1 is the cycle time of the peripheral clock 1 (CLKP1), Unit : ns
*1: Parameter N depends on tSCYCI and can be calculated as follows:
• if tSCYCI = 2*k*tCLKP1, then N = k, where k is an integer > 2
• if tSCYCI = (2*k+1)*tCLKP1, then N = k+1, where k is an integer > 1
Examples:
tSCYCI
N
94
4*tCLKP1
2
5*tCLKP1, 6*tCLKP1
3
7*tCLKP1, 8*tCLKP1
4
...
...
FME-MB96340 rev 10
MB96340 Series
tSCYCI
SCK for
ESCR:SCES = 0
0.8*VCC
0.2*VCC
0.2*VCC
SCK for
ESCR:SCES = 1
0.8*VCC
0.8*VCC
0.2*VCC
tSLOVI
tOVSHI
0.8*VCC
SOT
0.2*VCC
tSHIXI
tIVSHI
SIN
VIH
VIH
VIL
VIL
Internal Shift Clock Mode
tSLSHE
SCK for
ESCR:SCES = 0
tSHSLE
VIH
VIH
VIL
VIL
VIH
VIL
tFE
VIH
VIL
VIL
SCK for
ESCR:SCES = 1
VIH
tSLOVE
tRE
SOT
0.8*VCC
0.2*VCC
tIVSHE
SIN
tSHIXE
VIH
VIH
VIL
VIL
External Shift Clock Mode
FME-MB96340 rev 10
95
MB96340 Series
I2C Timing
(TA = -40˚C to 125˚C, VCC = AVCC = 3.0V to 5.5V,VSS = AVSS =0V)
Parameter
Standard-mode
Symbol
Fast-mode*1
Unit
Min
Max
Min
Max
fSCL
0
100
0
400
kHz
tHDSTA
4.0
⎯
0.6
⎯
µs
“L” width of the SCL clock
tLOW
4.7
⎯
1.3
⎯
µs
“H” width of the SCL clock
tHIGH
4.0
⎯
0.6
⎯
µs
Set-up time for a repeated START condition
SCL↑→SDA↓
tSUSTA
4.7
⎯
0.6
⎯
µs
Data hold time
SCL↓→SDA↓↑
tHDDAT
0
3.45
0
0.9
µs
Data set-up time
SDA↓↑→SCL↑
tSUDAT
250
⎯
100
⎯
ns
Set-up time for STOP condition
SCL↑→SDA↑
tSUSTO
4.0
⎯
0.6
⎯
µs
Bus free time between a STOP and START
condition
tBUS
4.7
⎯
1.3
⎯
µs
Output fall time from 0.7*Vcc to 0.3*Vcc with
a bus capacitance from 10 pF to 400 pF
tof
20 + 0.1*Cb *2
250
20 + 0.1*Cb *2
250
ns
Capacitive load for each bus line
Cb
⎯
400
⎯
400
pF
Pulse width of spikes which will be suppressed by input noise filter
tSP
n/a
n/a
0
1*tCLKP1*3
ns
SCL clock frequency
Hold time (repeated) START condition
SDA↓→SCL↓
*1 : For use at over 100 kHz, set the peripheral clock 1 to at least 6 MHz.
*2 : Cb = capacitance of one bus line in pF.
*3 : tCLKP1 is the cycle time of the periperal clock CLKP1.
SDA
tSUDAT
tLOW
tBUS
tHDSTA
SCL
tHDSTA
tHDDAT
tHIGH
tSUSTA
tSUSTO
• VOH = 0.7 * VCC
• VOL = 0.3 * VCC
• CMOS Hysteresis 0.7/0.3 input selected
96
FME-MB96340 rev 10
MB96340 Series
5. Analog Digital Converter
(TA = -40 ˚C to +125 ˚C, 3.0 V ≤ AVRH - AVRL, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Pin
Resolution
-
Total error
Value
Unit
Min
Typ
Max
-
-
-
10
bit
-
-
-
-
±3
LSB
Nonlinearity error
-
-
-
-
± 2.5
LSB
Differential nonlinearity
error
-
-
-
± 1.9
LSB
Zero transition voltage
VOT
ANn
AVRL - AVRL+ AVRL +
1.5 LSB 0.5 LSB 2.5 LSB
V
Full scale transition
voltage
VFST
ANn
AVRH - AVRH - AVRH +
3.5 LSB 1.5 LSB 0.5 LSB
V
Compare time
-
-
Sampling time
-
-
-
Remarks
1.0
-
16,500
µs
4.5V ≤ ΑVCC ≤ 5.5V
2.0
-
-
µs
3.0V ≤ ΑVCC < 4.5V
0.5
-
-
µs
4.5V ≤ ΑVCC ≤ 5.5V
1.2
-
-
µs
3.0V ≤ ΑVCC < 4.5V
-1
-
+1
-1.2
-
+1.2
TA ≤ 105 ˚C,
µA AVSS, AVRL < VI <
AVCC, AVRH
Analog input leakage
current (during conversion)
IAIN
Analog input voltage
range
VAIN
ANn
AVRL
-
AVRH
V
AVRH
AVRH/
AVRH2
0.75
AVcc
-
AVcc
V
AVRL
AVRL
AVSS
-
0.25
AVCC
V
IA
AVcc
-
2.5
5
mA A/D Converter active
IAH
AVcc
-
-
5
µA
IR
AVRH/
AVRL
-
0.7
1
mA A/D Converter active
IRH
AVRH/
AVRL
-
-
5
µA
-
ANn
-
-
4
LSB
Reference voltage
range
Power supply current
Reference voltage current
Offset between input
channels
ANn
105 ˚C < TA ≤ 125 ˚C,
µA AVSS, AVRL < VI <
AVCC, AVRH
A/D Converter not operated
A/D Converter not operated
Note: The accuracy gets worse as |AVRH - AVRL| becomes smaller.
FME-MB96340 rev 10
97
MB96340 Series
Definition of A/D Converter Terms
Resolution: Analog variation that is recognized by an A/D converter.
Total error: Difference between the actual value and the ideal value. The total error includes zero transition error,
full-scale transition error and nonlinearity error.
Nonlinearity error: Deviation between a line across zero-transition line (“00 0000 0000” <--> “00 0000 0001”)
and full-scale transition line (“11 1111 1110” <--> “11 1111 1111”) and actual conversion characteristics.
Differential nonlinearity error: Deviation of input voltage, which is required for changing output code by 1 LSB,
from an ideal value.
Zero reading voltage: Input voltage which results in the minimum conversion value.
Full scale reading voltage: Input voltage which results in the maximum conversion value.
Total error
3FF
3FE
Actual conversion
characteristics
1.5 LSB
Digital output
3FD
{1 LSB × (N − 1) + 0.5 LSB}
004
VNT
(Actually-measured value)
003
Actual conversion
characteristics
Ideal characteristics
002
001
0.5 LSB
AVRL
AVRH
Analog input
VNT − {1 LSB × (N − 1) + 0.5 LSB}
1 LSB
AVRH − AVRL
1 LSB = (Ideal value)
[V]
1024
Total error of digital output “N” =
[LSB]
N: A/D converter digital output value
VOT (Ideal value) = AVRL + 0.5 LSB [V]
VFST (Ideal value) = AVRH − 1.5 LSB [V]
VNT : A voltage at which digital output transitions from (N − 1) to N.
98
FME-MB96340 rev 10
MB96340 Series
Nonlinearity error
Differential nonlinearity error
Ideal
characteristics
3FF
Digital output
3FD
Actual conversion
characteristics
{1 LSB × (N − 1)
+ VOT }
N+1
VFST (actual
measurement
value)
VNT (actual
measurement value)
004
Actual conversion
characteristics
003
Digital output
3FE
Actual conversion
characteristics
N
V (N + 1) T
(actual measurement
value)
VNT
(actual measurement value)
N−1
002
Ideal characteristics
Actual conversion
characteristics
N−2
001
VOT (actual measurement value)
AVRL
AVRH
AVRL
Analog input
AVRH
Analog input
Nonlinearity error of digital output N =
Differential nonlinearity error of digital output N =
1 LSB =
VNT − {1 LSB × (N − 1) + VOT}
1 LSB
V (N+1) T − VNT
1 LSB
VFST − VOT
1022
[LSB]
−1 LSB [LSB]
[V]
N
: A/D converter digital output value
VOT : Voltage at which digital output transits from “000H” to “001H.”
VFST : Voltage at which digital output transits from “3FEH” to “3FFH.”
FME-MB96340 rev 10
99
MB96340 Series
Accuracy and setting of the A/D Converter sampling time
If the external impedance is too high or the sampling time too short, the analog voltage charged to the internal
sample and hold capacitor is insufficient, adversely affecting the A/D conversion precision.
To satisfy the A/D conversion precision, a sufficient sampling time must be selected. The required sampling time
depends on the external driving impedance Rext, the board capacitance of the A/D converter input pin Cext and
the AVcc voltage level. The following replacement model can be used for the calculation:
MCU
Analog
input
Rext
RADC
Comparator
Source
Cext
CIN
CADC
Sampling switch
Rext: external driving impedance
Cext: capacitance of PCB at A/D converter input
CIN: capacitance of MCU input pin: 15pF (max)
RADC: resistance within MCU: 2.6kΩ (max) for 4.5V ≤ AVcc ≤ 5.5V
12kΩ (max) for 3.0V ≤ AVcc < 4.5V
CADC: sampling capacitance within MCU: 10pF (max)
The sampling time should be set to minimum “7τ“. The following approximation formula for the replacement
model above can be used:
Tsamp [min] = 7 × (Rext × (Cext + CIN) + (Rext + RADC) × CADC)
• Do not select a sampling time below the absolute minimum permitted value
(0.5µs for 4.5V ≤ AVcc ≤ 5.5V; 1.2 µs for 3.0V ≤ AVcc < 4.5V).
• If the sampling time cannot be sufficient, connect a capacitor of about 0.1 µF to the analog input pin. In this
case the internal sampling capacitance CADC will be charged out of this external capacitance.
• A big external driving impedance also adversely affects the A/D conversion precision due to the pin input
leakage current IIL (static current before the sampling switch) or the analog input leakage current IAIN (total
leakage current of pin input and comparator during sampling). The effect of the pin input leakage current IIL
cannot be compensated by an external capacitor.
• The accuracy gets worse as |AVRH - AVRL| becomes smaller.
100
FME-MB96340 rev 10
MB96340 Series
6. Alarm Comparator
(TA = -40 ˚C to +125 ˚C, VCC = AVCC = 3.0V - 5.5V, VSS = AVSS = 0V)
Parameter
Symbol
Pin
IA5ALMF
Power supply current
IA5ALMS
AVCC
IA5ALMH
ALARM pin input current
IALIN
ALARM pin input voltage range
VALIN
External low threshold
high->low transition
VEVTL(H->L)
External low threshold
low->high transition
VEVTL(L->H)
Value
Unit
Remarks
45
µA
Alarm comparator
enabled in fast
mode (one channel)
7
13
µA
Alarm comparator
enabled in slow
mode (one channel)
-
-
5
µA
Alarm comparator
disabled
-1
-
+1
µA TA = 25 ˚C
-3
-
+3
µA TA = 125 ˚C
0
-
AVCC
V
-
V
Min
Typ
Max
-
25
-
0.36 * AVCC 0.36 * AVCC
-0.25
-0.1
-
0.36 * AVCC 0.36 * AVCC
+0.1
+0.25
INTREF = 0
External high threshold
high->low transition
VEVTH(H->L)
External high threshold
low->high transition
VEVTH(L->H)
Internal low threshold
high->low transition
VIVTL(H->L)
Internal low threshold
low->high transition
VIVTL(L->H)
Internal high threshold
high->low transition
VIVTH(H->L)
2.2
2.4
-
V
Internal high threshold
low->high transition
VIVTH(L->H)
-
2.6
2.85
V
VHYS
50
-
300
mV
tCOMPF
-
0.1
1
µs
CMD = 1 (fast)
tCOMPS
-
1
10
µs
CMD = 0 (slow)
Power-up stabilization
time after enabling
alarm comparator
tPD
-
1
10
ms
Slow/Fast mode transition time
tCMD
-
100
500
µs
Threshold levels
specified above are
not guaranteed
within this time
Switching hysteresis
Comparison time
FME-MB96340 rev 10
0.78 * AVCC 0.78 * AVCC
-0.25
-0.1
V
-
0.78 * AVCC 0.78 * AVCC
+0.1
+0.25
ALARM0,
ALARM1
V
V
0.9
1.1
-
V
-
1.3
1.55
V
INTREF = 1
101
MB96340 Series
Comparator
Output
H
L
VxVTx(H->L)
VHYS
VALIN
VxVTx(L->H)
102
FME-MB96340 rev 10
MB96340 Series
7. Low Voltage Detector characteristics
(TA = -40 ˚C to +125 ˚C, Vcc = AVcc = 3.0V - 5.5V, Vss = AVss = 0V)
Parameter
Symbol
Stabilization time
Value *1
Value *2
Unit
Remarks
110
µs
After power-up or change
of detection level
2.5
2.9
V
CILCR:LVL[3:0]=”0000”
3.1
2.8
3.2
V
CILCR:LVL[3:0]=”0001”
3.1
3.3
3
3.4
V
CILCR:LVL[3:0]=”0010”
VDL3
3.5
3.75
3.35
3.8
V
CILCR:LVL[3:0]=”0011”
Level 4
VDL4
3.6
3.85
3.5
3.95
V
CILCR:LVL[3:0]=”0100”
Level 5
VDL5
3.7
3.95
3.6
4.1
V
CILCR:LVL[3:0]=”0101”
Level 6
VDL6
3.8
4.05
3.7
4.2
V
CILCR:LVL[3:0]=”0110”
Level 7
VDL7
3.9
4.15
3.8
4.3
V
CILCR:LVL[3:0]=”0111”
Level 8
VDL8
4.0
4.25
3.9
4.4
V
CILCR:LVL[3:0]=”1000”
Level 9
VDL9
4.1
4.35
3.95
4.5
V
CILCR:LVL[3:0]=”1001”
Level 10
VDL10
not used
not used
Level 11
VDL11
not used
not used
Level 12
VDL12
not used
V
CILCR:LVL[3:0]=”1100”
Level 13
VDL13
not used
not used
Level 14
VDL14
not used
not used
Level 15
VDL15
not used
not used
Min
Max
Min
Max
TLVDSTAB
-
75
-
Level 0
VDL0
2.7
2.9
Level 1
VDL1
2.9
Level 2
VDL2
Level 3
2.6
3
*1: valid for all devices except devices listed under “*2”
*2: valid for: MB96F345
CILCR:LVL[3:0] are the low voltage detector level select bits of the CILCR register.
V
For correct detection, the slope of the voltage level must satisfy dV ≤ 0.004 ----- .
dt
µs
Faster variations are regarded as noise and may not be detected.
The functional operation of the MCU is guaranteed down to the minimum low voltage detection level of
“Level 0” (VDL0_MIN). The electrical characteristics however are only valid in the specified range (usually down to
3.0V).
FME-MB96340 rev 10
103
MB96340 Series
Low Voltage Detector Operation
In the following figure, the occurrence of a low voltage condition is illustrated. For a detailed description of the
reset and startup behavior, please refer to the corresponding hardware manual chapter.
Voltage [V]
VCC
VDLx, Max
VDLx, Min
dV
dt
Time [s]
Normal Operation
104
Low Voltage Reset Assertion
Power Reset Extension Time
FME-MB96340 rev 10
MB96340 Series
8. FLASH memory program/erase characteristics
(TA = -40˚C to 105˚C, VCC = AVCC = 3.0V to 5.5V, VSS = AVSS = 0V)
Parameter
Value
Unit
Remarks
3.6
s
Without erasure pre-programming time
0.5
2
s
Without erasure pre-programming time
-
0.8
3.6
s
Including erasure pre-programming time
-
n*0.9
n*3.6
s
Without erasure pre-programming time (n is the number of
Flash sector of the device)
Chip erase time
-
2.5
10
s
Without erasure pre-programming time
Data Flash
-
3.7
16.4
s
Including erasure pre-programming time
-
23
370
us
Without overhead time for submitting write command
-
15
100
us
Without overhead time for submitting write command
10 000
-
-
cycle
100 000 Program/Erase cycles
are under evaluation by Fujitsu
Microelectronics
20
-
-
year
*1
Min
Typ
Max
-
0.9
Sector erase time
-
Data Flash
Sector erase time
Program/Data Flash (Main Flash)
Chip erase time
Program/Data Flash (Main Flash)
Word (16-bit width) programming time
Program/Data Flash (Main Flash)
Byte (8-bit width) programming time
Data Flash
Program/Erase cycle
Flash data retention time
*1: This value was converted from the results of evaluating the reliability of the technology (using Arrhenius
equation to convert high temperature measurements into normalized value at 85oC)
FME-MB96340 rev 10
105
MB96340 Series
■ EXAMPLE CHARACTERISTICS
1. Temperature dependency of power supply currents
The following diagrams show the current consumption of samples with typical wafer process parameters in different operation modes.
Common condition for all operation modes:
• VCC = AVCC = 5.0V
• Main clock = 4MHz external clock
• Sub clock = 32kHz external clock
Operation mode details:
Mode name
Details
PLL Run 56
PLL Run mode current ICCPLL with the following settings:
• fCLKS1 = fCLKS2 = fCLKB = fCLKP1 = 56MHz
• fCLKP2 = 28MHz
• Regulator in High Power Mode
• Core voltage at 1.9V (VRCR:HPM[1:0] = 11B)
• 2 Flash/ROM wait states (MTCRA=233AH)
• RC oscillator and Sub oscillator stopped
PLL Run 48
PLL Run mode current ICCPLL with the following settings:
• fCLKS1 = fCLKS2 = 96MHz
• fCLKB = fCLKP1 = 48MHz
• fCLKP2 = 24MHz
• Regulator in High Power Mode
• Core voltage at 1.9V (VRCR:HPM[1:0] = 11B)
• 1 Flash/ROM wait states (MTCRA=6B09H)
• RC oscillator and Sub oscillator stopped
PLL Run 40
PLL Run mode current ICCPLL with the following settings:
• fCLKS1 = fCLKS2 = 80MHz
• fCLKB = fCLKP1 = 40MHz
• fCLKP2 = 20MHz
• Regulator in High Power Mode
• Core voltage at 1.9V (VRCR:HPM[1:0] = 11B)
• 1 Flash/ROM wait states (MTCRA=6B09H)
• RC oscillator and Sub oscillator stopped
PLL Run 36
PLL Run mode current ICCPLL with the following settings:
• fCLKS1 = fCLKS2 = 72MHz
• fCLKB = fCLKP1 = 36MHz
• fCLKP2 = 18MHz
• Regulator in High Power Mode
• Core voltage at 1.9V (VRCR:HPM[1:0] = 11B)
• 1 Flash/ROM wait states (MTCRA=6B09H)
• RC oscillator and Sub oscillator stopped
106
FME-MB96340 rev 10
MB96340 Series
Mode name
Details
PLL Run 24
PLL Run mode current ICCPLL with the following settings:
• fCLKS1 = fCLKS2 = 48MHz
• fCLKB = fCLKP1 = fCLKP2 = 24MHz
• Regulator in High Power Mode
• Core voltage at 1.8V (VRCR:HPM[1:0] = 10B)
• 0 Flash/ROM wait states (MTCRA=2208H)
• RC oscillator and Sub oscillator stopped
Main Run
Main Run mode current ICCMAIN with the following settings:
• fCLKS1 = fCLKS2 = fCLKB = fCLKP1 = fCLKP2 = 4MHz
• Regulator in High Power Mode
• Core voltage at 1.8V (VRCR:HPM[1:0] = 10B)
• 1 Flash/ROM wait states (MTCRA=0239H)
• PLL, RC oscillator and Sub oscillator stopped
RC Run 2M
RC Run mode current ICCRCH with the following settings:
• RC oscillator set to 2MHz (CKFCR:RCFS = 1)
• fCLKS1 = fCLKS2 = fCLKB = fCLKP1 = fCLKP2 = 2MHz
• Regulator in High Power Mode
• Core voltage at 1.8V (VRCR:HPM[1:0] = 10B)
• 1 Flash/ROM wait states (MTCRA=0239H)
• PLL, Main oscillator and Sub oscillator stopped
RC Run 100k
RC Run mode current ICCRCL with the following settings:
• RC oscillator set to 100kHz (CKFCR:RCFS = 0)
• fCLKS1 = fCLKS2 = fCLKB = fCLKP1 = fCLKP2 = 100kHz
• Regulator in Low Power Mode A (SMCR:LPMS = 1)
• Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B)
• 1 Flash/ROM wait states (MTCRA=0239H)
• PLL, Main oscillator and Sub oscillator stopped
Sub Run
Sub Run mode current ICCSUB with the following settings:
• fCLKS1 = fCLKS2 = fCLKB = fCLKP1 = fCLKP2 = 32kHz
• Regulator in Low Power Mode A (by hardware)
• Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B)
• 1 Flash/ROM wait states (MTCRA=0239H)
• PLL, RC oscillator and Main oscillator stopped
PLL Sleep 56
PLL Sleep mode current ICCSPLL with the following settings:
• fCLKS1 = fCLKS2 = fCLKP1 = 56MHz
• fCLKP2 = 28MHz
• Regulator in High Power Mode
• Core voltage at 1.9V (VRCR:HPM[1:0] = 11B)
• RC oscillator and Sub oscillator stopped
FME-MB96340 rev 10
107
MB96340 Series
Mode name
Details
PLL Sleep 48
PLL Sleep mode current ICCSPLL with the following settings:
• fCLKS1 = fCLKS2 = 96MHz
• fCLKP1 = 48MHz
• fCLKP2 = 24MHz
• Regulator in High Power Mode
• Core voltage at 1.9V (VRCR:HPM[1:0] = 11B)
• RC oscillator and Sub oscillator stopped
PLL Sleep 40
PLL Sleep mode current ICCSPLL with the following settings:
• fCLKS1 = fCLKS2 = 80MHz
• fCLKP1 = 40MHz
• fCLKP2 = 20MHz
• Regulator in High Power Mode
• Core voltage at 1.9V (VRCR:HPM[1:0] = 11B)
• RC oscillator and Sub oscillator stopped
PLL Sleep 36
PLL Sleep mode current ICCSPLL with the following settings:
• fCLKS1 = fCLKS2 = 72MHz
• fCLKP1 = 36MHz
• fCLKP2 = 18MHz
• Regulator in High Power Mode
• Core voltage at 1.9V (VRCR:HPM[1:0] = 11B)
• RC oscillator and Sub oscillator stopped
PLL Sleep 24
PLL Sleep mode current ICCSPLL with the following settings:
• fCLKS1 = fCLKS2 = 48MHz
• fCLKP1 = fCLKP2 = 24MHz
• Regulator in High Power Mode
• Core voltage at 1.8V (VRCR:HPM[1:0] = 10B)
• RC oscillator and Sub oscillator stopped
Main Sleep
Main Sleep mode current ICCSMAIN with the following settings:
• fCLKS1 = fCLKS2 = fCLKP1 = fCLKP2 = 4MHz
• Regulator in High Power Mode
• Core voltage at 1.8V (VRCR:HPM[1:0] = 10B)
• PLL, RC oscillator and Sub oscillator stopped
RC Sleep 2M
RC Sleep mode current ICCSRCH with the following settings:
• RC oscillator set to 2MHz (CKFCR:RCFS = 1)
• fCLKS1 = fCLKS2 = fCLKP1 = fCLKP2 = 2MHz
• Regulator in High Power Mode
• Core voltage at 1.8V (VRCR:HPM[1:0] = 10B)
• PLL, Main oscillator and Sub oscillator stopped
RC Sleep 100k
RC Sleep mode current ICCSRCL with the following settings:
• RC oscillator set to 100kHz (CKFCR:RCFS = 0)
• fCLKS1 = fCLKS2 = fCLKP1 = fCLKP2 = 100kHz
• Regulator in Low Power Mode A (SMCR:LPMSS = 1)
• Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B)
• PLL, Main oscillator and Sub oscillator stopped
108
FME-MB96340 rev 10
MB96340 Series
Mode name
Details
Sub Sleep
Sub Sleep mode current ICCSSUB with the following settings:
• fCLKS1 = fCLKS2 = fCLKP1 = fCLKP2 = 32kHz
• Regulator in Low Power Mode A (by hardware)
• Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B)
• PLL, RC oscillator and Main oscillator stopped
PLL Timer 48
PLL Timer mode current ICCTPLL with the following settings:
• fCLKS1 = fCLKS2 = 48MHz
• Regulator in High Power Mode
• Core voltage at 1.8V (VRCR:HPM[1:0] = 10B)
• RC oscillator and Sub oscillator stopped
Main Timer
Main Timer mode current ICCTMAIN with the following settings:
• fCLKS1 = fCLKS2 = 4MHz
• Regulator in Low Power Mode A (SMCR:LPMSS = 1)
• Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B)
• PLL, RC oscillator and Sub oscillator stopped
RC Timer 2M
RC Timer mode current ICCTRCH with the following settings:
• RC oscillator set to 2MHz (CKFCR:RCFS = 1)
• fCLKS1 = fCLKS2 = 2MHz
• Regulator in Low Power Mode A (SMCR:LPMSS = 1)
• Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B)
• PLL, Main oscillator and Sub oscillator stopped
RC Timer 100k
RC Timer mode current ICCTRCL with the following settings:
• RC oscillator set to 100kHz (CKFCR:RCFS = 0)
• fCLKS1 = fCLKS2 = 100kHz
• Regulator in Low Power Mode A (SMCR:LPMSS = 1)
• Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B)
• PLL, Main oscillator and Sub oscillator stopped
Sub Timer
Sub Timer mode current ICCTSUB with the following settings:
• fCLKS1 = fCLKS2 = 32kHz
• Regulator in Low Power Mode A (by hardware)
• Core voltage at 1.8V (VRCR:LPMA[2:0] = 110B)
• PLL, RC oscillator and Main oscillator stopped
Stop 1.8V
Stop mode current ICCH with the following settings:
• Regulator in Low Power Mode B (by hardware)
• Core voltage at 1.8V (VRCR:LPMB[2:0] = 110B)
Stop 1.2V
Stop mode current ICCH with the following settings:
• Regulator in Low Power Mode B (by hardware)
• Core voltage at 1.2V (VRCR:LPMB[2:0] = 000B)
FME-MB96340 rev 10
109
MB96340 Series
MB96345/346 PLL Run and Sleep mode currents
25
PLL Run 48
PLL Run 56
20
15
Icc[mA]
PLL Run 24
PLL Sleep 48
PLL Sleep 56
10
PLL Sleep 24
5
0
-60
-40
-20
0
20
40
60
80
100
120
Ta [˚C]
MB96345/346 operation modes with medium currents
3
2.5
Main Run
2
Icc[mA]
RC Run 2M
1.5
Main Sleep
PLL Timer 48
1
RC Sleep 2M
0.5
0
-60
-40
-20
0
20
40
60
80
100
120
Ta [˚C]
110
FME-MB96340 rev 10
MB96340 Series
MB96345/346 Low power mode currents
Icc[mA]
1
0.1
Main Timer
RC Run 100k
RC Timer 2M
RC Sleep 100k
Sub Run
Sub Sleep
Sub Timer
RC Timer 100k
Stop 1.8V
Stop 1.2V
0.01
-60
-40
-20
0
20
40
60
80
100
120
Ta [˚C]
MB96F345 PLL Run and Sleep mode currents
40
PLL Run 40
30
PLL Run 24
Icc[mA]
20
PLL Sleep 40
10
PLL Sleep 24
0
-60
-40
-20
0
20
40
60
80
100
120
Ta [˚C]
FME-MB96340 rev 10
111
MB96340 Series
MB96F345 operation modes with medium currents
5
4
Main Run
Icc[mA]
3
RC Run 2M
2
PLL Timer 48
1
Main Sleep
RC Sleep 2M
0
-60
-40
-20
0
20
40
60
80
100
120
80
100
120
Ta [˚C]
MB96F345 Low power mode currents
1
RC Run 100k
0.1
Icc[mA]
Sub Run
Main Timer
RC Timer 2M
Sub Sleep
RC Sleep 100k
Sub Timer
RC Timer 100k
0.01
Stop 1.8V
Stop 1.2V
0.001
-60
-40
-20
0
20
40
60
Ta [˚C]
112
FME-MB96340 rev 10
MB96340 Series
MB96F346/F347/F348Y/R/A PLL Run and Sleep mode currents
50
PLL Run 56
40
PLL Run 36
30
Icc[mA]
PLL Run 24
20
PLL Sleep 56
10
PLL Sleep 36
PLL Sleep 24
0
-60
-40
-20
0
20
40
60
80
100
120
Ta [˚C]
MB96F346/F347/F348Y/R/A operation modes with medium currents
5
Main Run
Icc[mA]
4
3
RC Run 2M
2
PLL Timer 48
Main Sleep
1
RC Sleep 2M
0
-60
-40
-20
0
20
40
60
80
100
120
Ta [˚C]
FME-MB96340 rev 10
113
MB96340 Series
MB96F346/F347/F348Y/R/A Low power mode currents
1
Icc[mA]
RC Run 100k
0.1
Sub Run
RC Timer 2M
Main Timer
RC Sleep 100k
Sub Sleep
Sub Timer
RC Timer 100k
Stop 1.8V
Stop 1.2V
0.01
-60
-40
-20
0
20
40
60
80
100
120
Ta [˚C]
MB96F348T/H/C PLL Run and Sleep mode currents
50
PLL Run 48
PLL Run 56
40
30
Icc[mA]
PLL Run 24
20
PLL Sleep 48
PLL Sleep 56
10
PLL Sleep 24
0
-60
-40
-20
0
20
40
60
80
100
120
Ta [˚C]
114
FME-MB96340 rev 10
MB96340 Series
MB96F348T/H/C operation modes with medium currents
6
5
Main Run
Icc[mA]
4
3
RC Run 2M
2
PLL Timer 48
Main Sleep
1
RC Sleep 2M
0
-60
-40
-20
0
20
40
60
80
100
120
100
120
Ta [˚C]
MB96F348T/H/C Low power mode currents
1
RC Run 100k
0.1
Icc[mA]
Sub Run
Main Timer
RC Timer 2M
RC Sleep 100k
Sub Sleep
Sub Timer
RC Timer 100k
0.01
Stop 1.8V
Stop 1.2V
0.001
-60
-40
-20
0
20
40
60
80
Ta [˚C]
FME-MB96340 rev 10
115
MB96340 Series
2. Frequency dependency of power supply currents in PLL Run mode
The following diagrams show the current consumption of samples with typical wafer process parameters in PLL
Run mode at different frequencies and Flash timing settings.
Measurement conditions:
• VCC = AVCC = 5.0V
• Ta = 25˚C
• fCLKS1 = fCLKB or fCLKS1 = 2*fCLKB as described in diagram
• fCLKS2 = fCLKS1
• fCLKP1 = fCLKB
• fCLKP2 = fCLKB/2
• Core voltage at 1.8V (VRCR:HPM[1:0] = 10B) or 1.9V (VRCR:HPM[1:0] = 11B) as described in diagram
• Main clock = 4MHz external clock
• Flash memory timing settings:
• MTCRA=2128H/2208H (0 Flash wait states, fCLKS1 = 2*fCLKB)
• MTCRA=0239H/2129H (1 Flash wait state, fCLKS1 = fCLKB)
• MTCRA=4C09H/6B09H (1 Flash wait state, fCLKS1 = 2*fCLKB)
• MTCRA=233AH (2 Flash wait states, fCLKS1 = fCLKB)
• Average Flash access rate (number of read accesses to the Flash per CLKB clock cycle, no buffer hit):
• 0 Flash wait states: 0.5
• 1 Flash wait states: 0.33
• 2 Flash wait states: 0.25
MB96F345 PLL Run mode currents
40
1 Flash wait state
(CLKS1=2*CLKB, 1.9V)
35
1 Flash wait state
(CLKS1=2*CLKB, 1.8V)
30
ICCPLL (mA)
25
0 Flash wait states
(CLKS1=2*CLKB, 1.8V)
2 Flash wait states
(CLKS1=CLKB, 1.9V)
20
2 Flash wait states
(CLKS1=CLKB, 1.8V)
15
10
1 Flash wait state
(CLKS1=CLKB, 1.8V)
: Specified in "DC characteristics"
5
0
0
4
8
12
16
20
24
28
32
36
40
CLKB/CLKP1 (MHz)
116
FME-MB96340 rev 10
MB96340 Series
MB96F346/F347/F348Y/R/A PLL Run mode currents
50
2 Flash wait states
(CLKS1=CLKB, 1.9V)
45
1 Flash wait state
(CLKS1=2*CLKB, 1.9V)
40
1 Flash wait state
(CLKS1=2*CLKB, 1.8V)
35
ICCPLL (mA)
30
25
0 Flash wait states
(CLKS1=2*CLKB, 1.8V)
2 Flash wait states
(CLKS1=CLKB, 1.8V)
20
15
1 Flash wait state
(CLKS1=CLKB, 1.8V)
10
: Specified in "DC characteristics"
5
0
0
4
8
12
16
20
24
28
32
36
40
44
48
52
56
CLKB/CLKP1 (MHz)
MB96F348T/H/C PLL Run mode currents
50
1 Flash wait state
(CLKS1=2*CLKB, 1.9V)
45
2 Flash wait states
(CLKS1=CLKB, 1.9V)
40
1 Flash wait state
(CLKS1=2*CLKB, 1.8V)
35
ICCPLL (mA)
30
25
0 Flash wait states
(CLKS1=2*CLKB, 1.8V)
2 Flash wait states
(CLKS1=CLKB, 1.8V)
20
15
1 Flash wait state
(CLKS1=CLKB, 1.8V)
10
: Specified in "DC characteristics"
5
0
0
4
8
12
16
20
24
28
32
36
40
44
48
52
56
CLKB/CLKP1 (MHz)
FME-MB96340 rev 10
117
MB96340 Series
■ PACKAGE DIMENSION MB96(F)34x LQFP 100P
100-pin plastic LQFP
Lead pitch
0.50 mm
Package width ×
package length
14.0 mm × 14.0 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
1.70 mm Max
Weight
0.65 g
Code
(Reference)
P-LFQFP100-14×14-0.50
(FPT-100P-M20)
100-pin plastic LQFP
(FPT-100P-M20)
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3) Pins width do not include tie bar cutting remainder.
16.00±0.20(.630±.008)SQ
* 14.00±0.10(.551±.004)SQ
75
51
76
50
0.08(.003)
Details of "A" part
+0.20
26
100
1
0.08(.003)
(0.50(.020))
0.25(.010)
0.60±0.15
(.024±.006)
25
0.20±0.05
(.008±.002)
0.10±0.10
(.004±.004)
(Stand off)
0˚~8˚
"A"
0.50(.020)
+.008
1.50 –0.10 .059 –.004
(Mounting height)
INDEX
M
0.145±0.055
(.0057±.0022)
©2005-2008
FUJITSU MICROELECTRONICS LIMITED F100031S-c-2-2
C
2005 FUJITSU LIMITED F100031S-c-2-1
Dimensions in mm (inches).
Note: The values in parentheses are reference values
Please check the latest package dimension at the following URL.
http://edevice.fujitsu.com/package/en-search/
118
FME-MB96340 rev 10
MB96340 Series
■ PACKAGE DIMENSION MB96(F)34x QFP 100P
100-pin plastic QFP
Lead pitch
0.65 mm
Package width ×
package length
14.00 mm × 20.00 mm
Lead shape
Gullwing
Sealing method
Plastic mold
Mounting height
3.35 mm MAX
Code
(Reference)
P-QFP100-14×20-0.65
(FPT-100P-M22)
100-pin plastic QFP
(FPT-100P-M22)
Note 1) * : These dimensions do not include resin protrusion.
Note 2) Pins width and pins thickness include plating thickness.
Note 3) Pins width do not include tie bar cutting remainder.
23.90±0.40(.941±.016)
* 20.00±0.20(.787±.008)
80
51
50
81
0.10(.004)
17.90±0.40
(.705±.016)
*14.00±0.20
(.551±.008)
INDEX
Details of "A" part
1
30
0.65(.026)
0.32±0.05
(.013±.002)
0.13(.005)
M
"A"
C
0.25(.010)
+0.35
3.00 –0.20
+.014
.118 –.008
(Mounting height)
0~8°
31
100
2006-2008 FUJITSU MICROELECTRONICS LIMITED F100033S-c-1-2
0.17±0.06
(.007±.002)
0.80±0.20
(.031±.008)
0.88±0.15
(.035±.006)
0.25±0.20
(.010±.008)
(Stand off)
Dimensions in mm (inches).
Note: The values in parentheses are reference values.
Please check the latest package dimension at the following URL.
http://edevice.fujitsu.com/package/en-search/
FME-MB96340 rev 10
119
MB96340 Series
■ ORDERING INFORMATION
MCU with CAN controller
Part number
Flash/ROM
MB96345YSA PQC-GSE2 *1
No
MB96345RSA PQC-GSE2 *1
MB96345YWA PQC-GSE2
*1
MB96345RWA PQC-GSE2
*1
Yes
ROM (160KB)
MB96345YSA PMC-GSE2 *1
No
MB96345RSA PMC-GSE2 *1
MB96345YWA PMC-GSE2
*1
MB96345RWA PMC-GSE2
*1
Yes
MB96346YSA PQC-GSE2 *1
No
MB96346RSA PQC-GSE2 *1
MB96346YWA PQC-GSE2
*1
MB96346RWA PQC-GSE2
*1
Yes
ROM (288KB)
MB96346YSA PMC-GSE2 *1
No
MB96346RSA PMC-GSE2 *1
MB96346YWA PMC-GSE2
*1
MB96346RWA PMC-GSE2
*1
Yes
MB96F345FSB PQC-GSE2 *1
No
MB96F345DSB PQC-GSE2 *1
MB96F345FWB PQC-GSE2
*1
MB96F345DWB PQC-GSE2
*1
MB96F345FSB PMC-GSE2 *1
MB96F345DSB PMC-GSE2 *1
MB96F345FWB PMC-GSE2
*1
MB96F345DWB PMC-GSE2
*1
120
Subclock
Yes
Flash A (160KB)
Data Flash A (64KB)
No
Yes
Persistent
Low Voltage Reset
Package
Yes
No
Yes
100 pin Plastic QFP
(FPT-100P-M22)
No
Yes
No
Yes
100 pin Plastic LQFP
(FPT-100P-M20)
No
Yes
No
Yes
100 pin Plastic QFP
(FPT-100P-M22)
No
Yes
No
Yes
100 pin Plastic LQFP
(FPT-100P-M20)
No
Yes
No
Yes
100 pin Plastic QFP
(FPT-100P-M22)
No
Yes
No
Yes
100 pin Plastic LQFP
(FPT-100P-M20)
No
FME-MB96340 rev 10
MB96340 Series
MCU with CAN controller
Part number
Flash/ROM
MB96F346YSB PQC-GSE2
No
MB96F346RSB PQC-GSE2
MB96F346YWB PQC-GSE2
Yes
MB96F346RWB PQC-GSE2
MB96F346YSB PMC-GSE2
No
MB96F346RSB PMC-GSE2
MB96F346YWB PMC-GSE2
MB96F346RWB PMC-GSE2
MB96F346YSC PQC-GSE2
Subclock
*1
Yes
Flash A (288KB)
No
*1
MB96F346RSC PQC-GSE2
MB96F346YWC PQC-GSE2*1
Yes
MB96F346RWC PQC-GSE2*1
*1
MB96F346YSC PMC-GSE2
No
*1
MB96F346RSC PMC-GSE2
MB96F346YWC PMC-GSE2*1
Yes
MB96F346RWC PMC-GSE2*1
MB96F347YSB PQC-GSE2
No
MB96F347RSB PQC-GSE2
MB96F347YWB PQC-GSE2
Yes
MB96F347RWB PQC-GSE2
MB96F347YSB PMC-GSE2
No
MB96F347RSB PMC-GSE2
MB96F347YWB PMC-GSE2
MB96F347RWB PMC-GSE2
MB96F347YSC PQC-GSE2
*1
*1
MB96F347RSC PQC-GSE2
MB96F347YWC PQC-GSE2*1
MB96F347RWC PQC-GSE2*1
Yes
Flash A (416KB)
No
Yes
*1
MB96F347YSC PMC-GSE2
*1
MB96F347RSC PMC-GSE2
MB96F347YWC PMC-GSE2*1
MB96F347RWC PMC-GSE2*1
FME-MB96340 rev 10
No
Yes
Persistent
Low Voltage Reset
Package
Yes
No
Yes
100 pin Plastic QFP
(FPT-100P-M22)
No
Yes
No
Yes
100 pin Plastic LQFP
(FPT-100P-M20)
No
Yes
No
100 pin Plastic QFP
(FPT-100P-M22)
Yes
No
Yes
No
100 pin Plastic LQFP
(FPT-100P-M20)
Yes
No
Yes
No
Yes
100 pin Plastic QFP
(FPT-100P-M22)
No
Yes
No
Yes
100 pin Plastic LQFP
(FPT-100P-M20)
No
Yes
No
Yes
100 pin Plastic QFP
(FPT-100P-M22)
No
Yes
No
Yes
100 pin Plastic LQFP
(FPT-100P-M20)
No
121
MB96340 Series
MCU with CAN controller
Part number
Flash/ROM
MB96F348YSB PQC-GSE2
No
MB96F348RSB PQC-GSE2
MB96F348YWB PQC-GSE2
Yes
MB96F348RWB PQC-GSE2
MB96F348YSB PMC-GSE2
No
MB96F348RSB PMC-GSE2
MB96F348YWB PMC-GSE2
MB96F348RWB PMC-GSE2
MB96F348YSC PQC-GSE2
Subclock
*1
Yes
Flash A (544KB)
No
*1
MB96F348RSC PQC-GSE2
MB96F348YWC PQC-GSE2*1
Yes
MB96F348RWC PQC-GSE2*1
*1
MB96F348YSC PMC-GSE2
No
*1
MB96F348RSC PMC-GSE2
MB96F348YWC PMC-GSE2*1
Yes
MB96F348RWC PMC-GSE2*1
MB96F348TSC PQC-GSE2
No
MB96F348HSC PQC-GSE2
MB96F348TWC PQC-GSE2
MB96F348HWC PQC-GSE2
MB96F348TSC PMC-GSE2
Yes
Flash A (544KB)
Flash B (32KB)
No
MB96F348HSC PMC-GSE2
MB96F348TWC PMC-GSE2
Yes
MB96F348HWC PMC-GSE2
MB96V300BRB-ES
(for evaluation)
122
Emulated by ext. RAM
Yes
Persistent
Low Voltage Reset
Package
Yes
No
Yes
100 pin Plastic QFP
(FPT-100P-M22)
No
Yes
No
Yes
100 pin Plastic LQFP
(FPT-100P-M20)
No
Yes
No
Yes
100 pin Plastic QFP
(FPT-100P-M22)
No
Yes
No
Yes
100 pin Plastic LQFP
(FPT-100P-M20)
No
Yes
No
Yes
100 pin Plastic QFP
(FPT-100P-M22)
No
Yes
No
Yes
100 pin Plastic LQFP
(FPT-100P-M20)
No
No
416 pin Plastic BGA
(BGA-416P-M02)
FME-MB96340 rev 10
MB96340 Series
MCU without CAN controller
Part number
Flash/ROM
Subclock
Package
MB96F346ASB PQC-GSE2
No
MB96F346AWB PQC-GSE2
Yes
100 pin Plastic QFP
(FPT-100P-M22)
MB96F346ASB PMC-GSE2
No
MB96F346AWB PMC-GSE2
Yes
MB96F346ASC PQC-GSE2*1
Flash A (288KB)
MB96F346AWC PQC-GSE2*1
No
Yes
*1
MB96F346ASC PMC-GSE2
No
*1
MB96F346AWC PMC-GSE2
Yes
MB96F347ASB PQC-GSE2
No
MB96F347AWB PQC-GSE2
Yes
MB96F347ASB PMC-GSE2
No
MB96F347AWB PMC-GSE2
Yes
MB96F347ASC PQC-GSE2*1
Flash A (416KB)
MB96F347AWC PQC-GSE2*1
MB96F347ASC PMC-GSE2
No
*1
MB96F347AWC PMC-GSE2
Yes
MB96F348ASB PQC-GSE2
No
MB96F348AWB PQC-GSE2
Yes
MB96F348ASB PMC-GSE2
No
MB96F348AWB PMC-GSE2
Yes
MB96F348ASC PQC-GSE2*1
Flash A (544KB)
MB96F348AWC PQC-GSE2*1
MB96F348ASC PMC-GSE2
No
*1
MB96F348AWC PMC-GSE2
Yes
MB96F348CSC PQC-GSE2
No
MB96F348CWC PQC-GSE2
MB96F348CSC PMC-GSE2
MB96F348CWC PMC-GSE2
Flash A (544KB)
Flash B (32KB)
100 pin Plastic QFP
(FPT-100P-M22)
100 pin Plastic LQFP
(FPT-100P-M20)
100 pin Plastic QFP
(FPT-100P-M22)
100 pin Plastic QFP
(FPT-100P-M22)
100 pin Plastic LQFP
(FPT-100P-M20)
No
Yes
*1
100 pin Plastic QFP
(FPT-100P-M22)
No
Yes
*1
100 pin Plastic LQFP
(FPT-100P-M20)
Yes
No
Yes
100 pin Plastic QFP
(FPT-100P-M22)
100 pin Plastic QFP
(FPT-100P-M22)
100 pin Plastic LQFP
(FPT-100P-M20)
*1: These devices are under development and specification is preliminary. These products under development may
change its specification without notice.
This datasheet is also valid for the following outdated devices:
MB96F346YSA, MB96F346RSA, MB96F346YWA, MB96F346RWA,
MB96F347YSA, MB96F347RSA, MB96F347YWA, MB96F347RWA,
MB96F348YSA, MB96F348RSA, MB96F348YWA, MB96F348RWA,
MB96F348TSB, MB96F348HSB, MB96F348TWB, MB96F348HWB,
FME-MB96340 rev 10
123
MB96340 Series
MB96F346ASA, MB96F346AWA,
MB96F347ASA, MB96F347AWA,
MB96F348ASA, MB96F348AWA,
MB96F348CSB, MB96F348CWB
124
FME-MB96340 rev 10
MB96340 Series
■ REVISION HISTORY
Revision
Date
Prelim 1
2007-05-07
Creation
Prelim 2
2007-05-10
External bus hold timing update
Prelim 3
2007-05-23
Electrical characteristics updates
Prelim 4
2007-08-02
Electrical characteristics updates, Product lineup, changes and ordering
information
Prelim 5
2007-09-12
Addition of the electrical characteristic examples and the LVD characteristics
specifications, updates of the DC characteristics. Pin circuit type drawing
modifications.
Prelim 6
2007-11-21
LVD typo correction.
Update of the DC characteristics. Typos corrections.
Prelim 7
2007-12-04
Absolute maximum rating asterisks numbering corrected.
Typos page 59: Hardware -> Hardware.
IO map table regenerated.
Typos corrections.
IO circuit drawings modified.
Renaming of the Main/Satellite Flash into Flash memory A/B.
Memory map reworked.
FME-MB96340 rev 10
Modification
125
MB96340 Series
Revision
Date
Prelim 8
2008-02-04
Modification
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
126
Satellite Flash -> 32kB Data Flash
MB96345 added (under development)
MB96F348 TSA/HSA/TWA/HWA removed (outdated devices)
Block diagram and pin assignment corrected (existing resource pins)
Pin function table corrected
I/O circuit type diagrams corrected
Memory map cleaned up
"Flash sector configuration" replaced by corrected "User ROM Memory map
for Flash devices", “ROM configuration” replaced by “User ROM Memory map
for Mask ROM devices”
Parallel Flash programming pinning removed
IO map table regenerated:
- Port register: Naming style corrected
- Memory control registers renamed (Main/Sat -> A/B)
- addresses after 000BFFh removed
Absolute maximum ratings: Pd and Ta specified more precisely
oscillator input levels in oscillation mode with external clock added
Run and Sleep mode currents: 96/48MHz and 72/36MHz settings added
Run mode current spec in 48/24MHz mode corrected
Maximum CLKS1/2 frequency for all devices correctly specified
Maximum CLKP2 for MB96F34xY/R/Axx corrected
External bus timings: missing conditions added and readability improved
Alarm comparator spec updated (transition voltages defined)
MB96V300A removed
Ordering information updated
Typos and formatting corrected
FME-MB96340 rev 10
MB96340 Series
Revision
Date
Modification
9
2009-01-09
• Format adjusted to official Fujitsu Microelectronics datasheet standard (mainly
style changes and official notes and disclaimer added)
• Numbering of Electrical Characteristics subchapters automated
• Note about devices under development modified
• I/O map: Note added about reserved addresses
• ICCSPLL for CLKS1=96MHz mode: increased by 1mA
• Serial programming interface: Note about handshaking pins improved
• specified AD converter channel offset to 4LSB
• package code of MB96V300 corrected in ordering information
• Added voltage condition to pull-up resistance spec
• Lineup: Term “Data Flash” replaced by “independent 32KB Flash”
• Ordering information: column “Independent 32KB Data Flash” replaced by new
column “Flash/ROM”, column “Remarks” removed
• Official package dimension drawing with additional notes added
• Empty pages removed
• Alarm comparator: Power supply current max values increased, comparison
time reduced, mode transition time and power-up stabilization time newly added
• Handling devices: Notes added about Serial communication and about using
ceramic resonators.
• Feature list and AC Characteristics: 16MHz maximum frequency is valid for
crystal oscillators. For resonators, maximum frequency depends on Q-factor
• AC characteristics: PLL phase skew spec added, CLKVCO min=64MHz
• VOL3 spec improved: spec valid for 3mA load for full Vcc range
• MB96F345 added
• Preliminary DC spec of MB96345/346 added
• Permitted power dissipation of Flash devices in QFP package improved
• C-Pin cap spec updated: 4.7uF-10uF capacitor with tolerance permitted
• “Preliminary” watermark removed
FME-MB96340 rev 10
127
MB96340 Series
Revision
Date
10
2010-06-23
FME-MB96340 rev 10
Modification
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
I/O map: IOABK0-5 added at address 000A00H-000A05H
Ordering Information: Suffix “A” added to all MB96F345 device versions
AD converter IAIN spec improved: 1uA valid up to 105deg, 1.2uA above 105deg
Corrected MB96F345 part names in ordering information
Low voltage detector: Detection levels of MB96F345 updated
Example characteristics updated, new figures added showing dependency of
PLL Run mode current on frequency
Updated Power Supply current spec in Run/Sleep/Timer/Stop modes (new
spec items in PLL Run/Sleep mode, small adjustment of most other values)
Note added that PLL phase jitter spec does not include jitter coming from Main
clock
Alarm comparator: Maximum power-up stabilization time increased to 10ms
Removed PHDR register from IO map
Note added in DC characteristics how to select driving strength of ports
I2C AC spec updated: tof, Cb and tSP spec added, wrong footnotes and Condition removed
I/O Circuit type: Note added for type “N” (slew rate control according to I2C spec)
Package dimension: Added the following sentence under the figure: “Please
confirm the latest Package dimension by following URL.
http://edevice.fujitsu.com/package/en-search/”
AD converter: Impact of input pin capacitance and external capacitance added
to formula for calculation of the sampling time
Added specification of RC clock stabilization time
Feature description I2C: ‘8-bit addressing’ corrected to ‘7-bit addressing’
Feature description PPG: ‘Reload timer overflow as clock input’ corrected to
‘Reload timer underflow as clock input’
Company name updated on the cover page: Fujitsu Microelectronics Limited > Fujitsu Semiconductor Limited
ICCLVD specification updated, at 125deg typical value is 7uA and maximum
value is 20uA
Ordering information: added devices under development MB96F346A*C,
MB96F347A*C, MB96F348A*C, MB96F346Y*C, MB96F347Y*C,
MB96F348Y*C, MB96F346R*C, MB96F347R*C, MB96F348R*C
MB96340 Series
FME-MB96340 rev 10
129
MB96340 Series
FUJITSU SEMICONDUCTOR LIMITED
Nomura Fudosan Shin-yokohama Bldg. 10-23, Shin-yokohama 2-Chome,
Kohoku-ku Yokohama Kanagawa 222-0033, Japan
Tel: +81-45-415-5858
http://jp.fujitsu.com/fsl/en/
For further information please contact:
North and South America
FUJITSU MICROELECTRONICS AMERICA, INC.
1250 E. Arques Avenue, M/S 333
Sunnyvale, CA 94085-5401, U.S.A.
Tel: +1-408-737-5600 Fax: +1-408-737-5999
http://www.fma.fujitsu.com/
Asia Pacific
FUJITSU MICROELECTRONICS ASIA PTE. LTD.
151 Lorong Chuan,
#05-08 New Tech Park 556741 Singapore
Tel : +65-6281-0770 Fax : +65-6281-0220
http://www.fmal.fujitsu.com/
Europe
FUJITSU MICROELECTRONICS EUROPE GmbH
Pittlerstrasse 47, 63225 Langen, Germany
Tel: +49-6103-690-0 Fax: +49-6103-690-122
http://emea.fujitsu.com/microelectronics/
FUJITSU MICROELECTRONICS SHANGHAI CO., LTD.
Rm. 3102, Bund Center, No.222 Yan An Road (E),
Shanghai 200002, China
Tel : +86-21-6146-3688 Fax : +86-21-6335-1605
http://cn.fujitsu.com/fmc/
Korea
FUJITSU MICROELECTRONICS KOREA LTD.
206 Kosmo Tower Building, 1002 Daechi-Dong,
Gangnam-Gu, Seoul 135-280, Republic of Korea
Tel: +82-2-3484-7100 Fax: +82-2-3484-7111
http://kr.fujitsu.com/fmk/
FUJITSU MICROELECTRONICS PACIFIC ASIA LTD.
10/F., World Commerce Centre, 11 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel : +852-2377-0226 Fax : +852-2376-3269
http://cn.fujitsu.com/fmc/en/
Specifications are subject to change without notice. For further information please contact each office.
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with sales representatives before ordering.
The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose
of reference to show examples of operations and uses of FUJITSU SEMICONDUCTOR device; FUJITSU SEMICONDUCTOR does
not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating
the device based on such information, you must assume any responsibility arising out of such use of the information.
FUJITSU SEMICONDUCTOR assumes no liability for any damages whatsoever arising out of the use of the information.
Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use
or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU SEMICONDUCTOR or any
third party or does FUJITSU SEMICONDUCTOR warrant non-infringement of any third-party's intellectual property right or other right
by using such information. FUJITSU SEMICONDUCTOR assumes no liability for any infringement of the intellectual property rights or
other rights of third parties which would result from the use of information contained herein.
The products described in this document are designed, developed and manufactured as contemplated for general use, including without
limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured
as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect
to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in
nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in
weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite).
Please note that FUJITSU SEMICONDUCTOR will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures
by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of overcurrent levels and other abnormal operating conditions.
Exportation/release of any products described in this document may require necessary procedures in accordance with the regulations
of the Foreign Exchange and Foreign Trade Control Law of Japan and/or US export control laws.
The company names and brand names herein are the trademarks or registered trademarks of their respective owners.
Edited: Sales Promotion Department
130
FME-MB96340 rev 10