MC10EP90, MC100EP90 −3.3V / −5VTriple ECL Input to LVPECL/PECL Output Translator Description The MC10/100EP90 is a TRIPLE ECL TO LVPECL/PECL translator. The device receives differential LVECL or ECL signals and translates them to differential LVPECL or PECL output signals. A VBB output is provided for interfacing with Single−Ended LVECL or ECL signals at the input. If a Single−Ended input is to be used the VBB output should be connected to the D input. The active signal would then drive the D input. When used the VBB output should be bypassed to ground by a 0.01 mF capacitor. The VBB output is designed to act as the switching reference for the EP90 under Single−Ended input switching conditions, as a result this pin can only source/sink up to 0.5 mA of current. To accomplish the level translation the EP90 requires three power rails. The VCC supply should be connected to the positive supply, and the VEE connected to the negative supply. The 100 Series contains temperature compensation. http://onsemi.com TSSOP−20 DT SUFFIX CASE 948E MARKING DIAGRAM* 20 xxxx EP90 ALYWG G Features • 260 ps Typical Propagation Delay • Maximum Frequency > 3 GHz Typical • Voltage Supplies VCC = 3.0 V to 5.5 V, VEE = −3.0 V to −5.5 V, • • • • • • GND = 0 V Open Input Default State Safety Clamp on Inputs Fully Differential Design Q Output Will Default LOW with Inputs Open or at VEE VBB Output These are Pb−Free Devices* 1 xxxx = MC10 or 100 A = Assembly Location L = Wafer Lot Y = Year W = Work Week G = Pb−Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 7 of this data sheet. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2006 November, 2006 − Rev. 6 1 Publication Order Number: MC10EP90/D MC10EP90, MC100EP90 VCC Q0 Q0 GND Q1 Q1 GND Q2 Q2 VCC 20 19 18 17 16 15 14 13 12 11 Table 1. PIN DESCRIPTION PIN FUNCTION Q(0:2), Q(0:2) Differential LVPECL or PECL Outputs D(0:2)*, D(0:2)* Differential LVECL or ECL Inputs LVPECL/ PECL LVPECL/ PECL ECL LVPECL/ PECL ECL ECL VCC Positive Supply GND Ground VEE Negative Supply VBB Output Reference Supply * Pins will default LOW when left open. Table 2. FUNCTION TABLE 1 2 3 4 5 6 7 8 9 10 VCC D0 D0 VBB D1 D1 VBB D2 D2 VEE Warning: All VCC, VEE and GND pins must be externally connected to Power Supply to guarantee proper operation. Figure 1. TSSOP−20 (Top View) and Logic Diagram Function VCC 5V 0V −5 V −5V ECL to 3.3V PECL 3.3 V 0V −5 V −3.3V ECL to 5V PECL 5V 0V −3.3 V −3.3V ECL to 3.3V PECL 3.3 V 0V −3.3 V Characteristics Value Internal Input Pulldown Resistor 75 kW Internal Input Pullup Resistor N/A Human Body Model Machine Model Charged Device Model Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) TSSOP−20 Flammability Rating Oxygen Index: 28 to 34 Transistor Count > 2 kV > 200 V > 2 kV Pb Pkg Pb−Free Pkg Level 1 Level 1 UL 94 V−0 @ 0.125 in 350 Devices Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, refer to Application Note AND8003/D. http://onsemi.com 2 VEE −5V ECL to 5V PECL Table 3. ATTRIBUTES ESD Protection GND MC10EP90, MC100EP90 Table 4. MAXIMUM RATINGS Rating Unit VCC Symbol PECL Mode Power Supply Parameter GND = 0 V Condition 1 6 V VEE NECL Mode Power Supply GND = 0 V −6 V VI PECL Mode Input Voltage NECL Mode Input Voltage GND = 0 V GND = 0 V 6 −6 V V Iout Output Current Continuous Surge 50 100 mA mA IBB VBB Sink/Source ± 0.5 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm TSSOP−20 TSSOP−20 140 100 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board TSSOP−20 23 to 41 °C/W Tsol Wave Solder <2 to 3 sec @ 248°C <2 to 3 sec @ 260°C 265 265 °C Pb Pb−Free Condition 2 VI VCC VI VEE Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. http://onsemi.com 3 MC10EP90, MC100EP90 Table 5. 10EP DC CHARACTERISTICS VCC = 3.3 V, VEE = −5.5 V to −3.0 V; GND = 0 V (Note 2) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit IEE Negative Power Supply Current 5 13 20 5 13 20 5 13 20 mA ICC Positive Power Supply Current 43 55 67 43 55 67 43 55 67 mA VOH Output HIGH Voltage (Note 3) 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV VOL Output LOW Voltage (Note 3) 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV VIH Input HIGH Voltage (Single−Ended) −1210 −885 −1145 −820 −1085 −760 mV VIL Input LOW Voltage (Single−Ended) −1935 −1610 −1870 −1545 −1810 −1485 mV VBB Output Voltage Reference −1510 −1310 −1445 −1245 −1385 −1185 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 4) 0.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current −1410 VEE+2.0 0.0 −1345 VEE+2.0 150 0.0 −1285 VEE+2.0 150 0.5 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 2. Input and output parameters vary 1:1 with VCC. 3. All loading with 50 W to VCC − 2.0 V. 4. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 6. 10EP DC CHARACTERISTICS VCC = 5.0 V, VEE = −5.5 V to −3.0 V; GND = 0 V (Note 5) −40°C Symbol Characteristic 25°C Min Typ Max 85°C Min Typ Max Min Typ Max Unit IEE Negative Power Supply Current 5 13 20 5 13 20 5 13 20 mA ICC Positive Power Supply Current 43 55 67 43 55 67 43 55 67 mA VOH Output HIGH Voltage (Note 6) 3865 3990 4115 3930 4055 4180 3990 4115 4240 mV VOL Output LOW Voltage (Note 6) 3065 3190 3315 3130 3255 3380 3190 3315 3440 mV VIH Input HIGH Voltage (Single−Ended) −1210 −885 −1145 −820 −1085 −760 mV VIL Input LOW Voltage (Single−Ended) −1935 −1610 −1870 −1545 −1810 −1485 mV VBB Output Voltage Reference −1510 −1310 −1445 −1245 −1385 −1185 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 7) 0.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current −1410 VEE+2.0 0.0 150 0.5 −1345 VEE+2.0 0.0 150 0.5 −1285 VEE+2.0 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. Input and output parameters vary 1:1 with VCC. 6. All loading with 50 W to VCC − 2.0 V. 7. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 4 MC10EP90, MC100EP90 Table 7. 100EP DC CHARACTERISTICS VCC = 3.3 V, VEE = −5.5 V to −3.0 V; GND = 0 V (Note 8) −40°C 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit IEE Negative Power Supply Current 5 13 20 5 13 20 5 13 20 mA ICC Positive Power Supply Current 45 58 70 50 62 75 53 65 78 mA VOH Output HIGH Voltage (Note 9) 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV VOL Output LOW Voltage (Note 9) 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV VIH Input HIGH Voltage (Single−Ended) −1225 −885 −1225 −885 −1225 −885 mV VIL Input LOW Voltage (Single−Ended) −1945 −1625 −1945 −1625 −1945 −1625 mV VBB Output Voltage Reference −1525 −1325 −1525 −1325 −1525 −1325 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 10) 0.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current Symbol Characteristic −1425 VEE+2.0 0.0 −1425 VEE+2.0 150 0.0 −1425 VEE+2.0 150 0.5 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 8. Input and output parameters vary 1:1 with VCC. 9. All loading with 50 W to VCC − 2.0 V. 10. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 8. 100EP DC CHARACTERISTICS VCC = 5.0 V, VEE = −5.5 V to −3.0 V; GND = 0 V (Note 11) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit IEE Negative Power Supply Current 5 13 20 5 13 20 5 13 20 mA ICC Positive Power Supply Current 45 58 70 50 62 75 53 65 78 mA VOH Output HIGH Voltage (Note 12) 3855 3980 4105 3855 3980 4105 3855 3980 4105 mV VOL Output LOW Voltage (Note 12) 3055 3180 3305 3055 3180 3305 3055 3180 3305 mV VIH Input HIGH Voltage (Single−Ended) −1225 −885 −1225 −885 −1225 −885 mV VIL Input LOW Voltage (Single−Ended) −1945 −1625 −1945 −1625 −1945 −1625 mV VBB Output Voltage Reference −1525 −1325 −1525 −1325 −1525 −1325 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 13) 0.0 V IIH Input HIGH Current 150 mA IIL Input LOW Current −1425 VEE+2.0 0.0 VEE+2.0 150 0.5 −1425 0.0 VEE+2.0 150 0.5 −1425 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 11. Input and output parameters vary 1:1 with VCC. 12. All loading with 50 W to VCC − 2.0 V. 13. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC.. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 5 MC10EP90, MC100EP90 Table 9. AC CHARACTERISTICS VEE = −3.0 V to −5.5 V; VCC = 3.0 V to 5.5 V; GND = 0 V (Note 14) −40°C Symbol Min Characteristic fmax Maximum Frequency (See Figure 2 Fmax/JITTER) tPLH, tPHL Propagation Delay to Output Differential tSKEW Duty Cycle Skew (Note 15) Typ 25°C Max Min >3 170 tJITTER Cycle−to−Cycle Jitter (See Figure 2 Fmax/JITTER) VPP Input Voltage Swing (Differential Configuration) tr tf Output Rise/Fall Times (20% − 80%) 310 5.0 20 200 Min Typ 0.2 <1 150 800 1200 70 120 170 Max >3 260 340 5.0 20 80 140 Q, Q 85°C Max >3 240 Within Device Skew Q, Q Device to Device Skew (Note 15) Typ 230 300 370 ps 5.0 20 ps 80 140 0.2 <1 150 800 1200 80 130 180 Unit GHz 80 140 0.2 <1 ps 150 800 1200 mV 100 150 230 ps 900 9 800 8 700 7 600 6 500 5 400 4 300 3 200 2 ÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉ 100 0 0 1000 2000 (JITTER) 3000 FREQUENCY (MHz) Figure 2. Fmax/Jitter http://onsemi.com 6 4000 1 5000 JITTER OUT ps (RMS) VOUTpp (mV) NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 14. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 W to VCC−2.0 V. 15. Skew is measured between outputs under identical transitions. Duty cycle skew is defined only for differential operation when the delays are measured from the cross point of the inputs to the cross point of the outputs. ÉÉ ÉÉ MC10EP90, MC100EP90 Q Zo = 50 W D Receiver Device Driver Device Q D Zo = 50 W 50 W 50 W VTT VTT = VCC − 2.0 V Figure 3. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices.) ORDERING INFORMATION Package Shipping † MC10EP90DT TSSOP−20* 75 Units / Rail MC10EP90DTG TSSOP−20* 75 Units / Rail MC10EP90DTR2 TSSOP−20* 2500 / Tape & Rail MC10EP90DTR2G TSSOP−20* 2500 / Tape & Rail MC100EP90DT TSSOP−20* 75 Units / Rail MC100EP90DTG TSSOP−20* 75 Units / Rail MC100EP90DTR2 TSSOP−20* 2500 / Tape & Rail MC100EP90DTR2G TSSOP−20* 2500 / Tape & Rail Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *This package is inherently Pb−Free. Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPSt I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1672/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices http://onsemi.com 7 MC10EP90, MC100EP90 PACKAGE DIMENSIONS TSSOP−20 CASE 948E−02 ISSUE C 20X 0.15 (0.006) T U 2X L K REF 0.10 (0.004) S L/2 20 M T U S V K K1 ÍÍÍÍ ÍÍÍÍ ÍÍÍÍ S J J1 11 B −U− PIN 1 IDENT SECTION N−N 0.25 (0.010) N 1 10 M 0.15 (0.006) T U S A −V− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. N F DETAIL E −W− C G D H DETAIL E 0.100 (0.004) −T− SEATING DIM A B C D F G H J J1 K K1 L M PLANE SOLDERING FOOTPRINT* 7.06 1 0.65 PITCH 16X 0.36 16X 1.26 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 8 MILLIMETERS MIN MAX 6.40 6.60 4.30 4.50 −−− 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.27 0.37 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.252 0.260 0.169 0.177 −−− 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.011 0.015 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC10EP90, MC100EP90 ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC10EP90/D