NB2308A 3.3 V Zero Delay Clock Buffer The NB2308A is a versatile, 3.3 V zero delay buffer designed to distribute high−speed clocks. It is available in a 16 pin package. The part has an on−chip PLL which locks to an input clock presented on the REF pin. The PLL feedback is required to be driven to FBK pin, and can be obtained from one of the outputs. The input−to−output propagation delay is guaranteed to be less than 250 ps, and the output−to−output skew is guaranteed to be less than 200 ps. The NB2308A has two banks of four outputs each, which can be controlled by the select inputs as shown in the Select Input Decoding Table. If all the output clocks are not required, Bank B can be three−stated. The select input also allows the input clock to be directly applied to the outputs for chip and system testing purposes. Multiple NB2308A devices can accept the same input clock and distribute it. In this case the skew between the outputs of the two devices is guaranteed to be less than 700 ps. The NB2308A is available in five different configurations (Refer to NB2308A Configurations Table). The NB2308Ax1* is the base part, where the output frequencies equal the reference if there is no counter in the feedback path. The NB2308Ax1H is the high−drive version of the −1 and the rise and fall times on this device are much faster. The NB2308Ax2 allows the user to obtain 2X and 1X frequencies on each output bank. The exact configuration and output frequencies depends on which output drives the feedback pin. The NB2308Ax3 allows the user to obtain 4X and 2X frequencies on the outputs. The NB2308Ax4 enables the user to obtain 2X clocks on all outputs. Thus, the part is extremely versatile, and can be used in a variety of applications. The NB2308Ax5H is a high−drive version with REF/2 on both banks. Features • Zero Input − Output Propagation Delay, Adjustable by Capacitive • • • • • • • • • • • Load on FBK Input Multiple Configurations − Refer to NB2308A Configurations Table Input Frequency Range: 15 MHz to 133 MHz Multiple Low−Skew Outputs Output−Output Skew Less than 200 ps Device−Device Skew Less than 700 ps Two banks of four outputs, three−stateable by two select inputs Less than 200 ps Cycle−to−Cycle Jitter Available in 16−pin SOIC and TSSOP Packages 3.3V operation Advanced 0.35 CMOS Technology These are Pb−Free Devices** http://onsemi.com MARKING DIAGRAMS* 16 16 XXXXXXXXXG AWLYWW 1 SOIC−16 D SUFFIX CASE 751B 1 16 16 1 TSSOP−16 DT SUFFIX CASE 948F 1 XXXX XXXX ALYWG G XXXX = Device Code A = Assembly Location WL, L = Wafer Lot Y = Year WW, W = Work Week G or G = Pb−Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. *x = C for Commercial; I for Industrial. **For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2006 November, 2006 − Rev. 3 1 Publication Order Number: NB2308A/D NB2308A FBK B2 PLL REF B2 CLKA1 Extra Divider (−3, −4) MUX CLKA2 Extra Divider (−5H) CLKA3 S2 CLKA4 SELECT INPUT DECODING S1 B2 CLKB1 Extra Divider (−2, −3) CLKB2 CLKB3 CLKB4 Figure 1. Block Diagram (see Figures 11, 12, 13, 14 and 15 for device specific Block Diagrams) Table 1. CONFIGURATIONS (x = C for Commercial; I for Industrial) Feedback From Device Bank A Frequency Bank B Frequency NB2308Ax1 Bank A or Bank B Reference Reference NB2308Ax1H Bank A or Bank B Reference Reference NB2308Ax2 Bank A Reference Reference B2 NB2308Ax2 Bank B 2 X Reference Reference NB2308Ax3 Bank A 2 X Reference Reference or Reference (Note 1) NB2308Ax3 Bank B 4 X Reference 2 X Reference NB2308Ax4 Bank A or Bank B 2 X Reference 2 X Reference NB2308Ax5H Bank A or Bank B Reference B2 Reference B2 1. Output phase is indeterminant (0° or 180° from input clock). If phase integrity is required, use the NB2308Ax2. Table 2. SELECT INPUT DECODING S2 S1 Clock A1 − A4 Clock B1 − B4 Output Source PLL ShutDown 0 0 Three−state Three−state PLL Y 0 1 Driven Three−state PLL N 1 0 Driven (Note 2) Driven Reference Y 1 1 Driven Driven PLL N 2. Outputs inverted on 2308−2 and 2308−3 in bypass mode, S2 = 1 and S1 = 0. http://onsemi.com 2 NB2308A REF 1 16 FBK CLKA1 2 15 CLKA4 CLKA2 3 14 CLKA3 VDD 4 13 VDD GND 5 12 GND CLKB1 6 11 CLKB4 CLKB2 7 10 CLKB3 S2 8 9 S1 NB2308A Figure 2. Pin Configuration Table 3. PIN DESCRIPTION Pin # Pin Name Description 1 REF (Note 3) 2 CLKA1 (Note 4) Buffered clock output, Bank A. 3 CLKA2 (Note 4) Buffered clock output, Bank A. Input reference frequency, 5 V tolerant input. 4 VDD 3.3 V supply. 5 GND Ground. 6 CLKB1 (Note 4) Buffered clock output, Bank B. 7 CLKB2 (Note 4) Buffered clock output, Bank B. 8 S2 (Note 5) Select input, bit 2. 9 S1 (Note 5) Select input, bit 1. 10 CLKB3 (Note 4) Buffered clock output, Bank B. 11 CLKB4 (Note 4) Buffered clock output, Bank B. 12 GND Ground. 13 VDD 3.3 V supply. 14 CLKA3 (Note 4) Buffered clock output, Bank A. 15 CLKA4 (Note 4) Buffered clock output, Bank A. 16 FBK PLL feedback input. 3. Weak pulldown. 4. Weak pulldown on all outputs. 5. Weak pullup on these inputs. http://onsemi.com 3 NB2308A Table 4. MAXIMUM RATINGS Parameter Min Max Unit Supply Voltage to Ground Potential −0.5 +7.0 V DC Input Voltage (Except REF) −0.5 VDD + 0.5 V DC Input Voltage (REF) −0.5 7 V Storage Temperature −65 +150 °C Maximum Soldering Temperature (10 sec) 260 °C Junction Temperature 150 °C >2000 V Static Discharge Voltage (per MIL−STD−883, Method 3015) Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. Table 5. OPERATING CONDITIONS FOR COMMERCIAL AND INDUSTRIAL TEMPERATURE DEVICES Parameter Description Min Max Unit 3.0 3.6 V 0 −40 70 85 °C VDD Supply Voltage TA Operating Temperature (Ambient Temperature) CL Load Capacitance, below 100 MHz 30 pF CL Load Capacitance, from 100 MHz to 133 MHz 15 pF CIN Input Capacitance (Note 6) 7 pF Commercial Industrial 6. Applies to both REF Clock and FBK. Table 6. ELECTRICAL CHARACTERISTICS FOR COMMERCIAL AND INDUSTRIAL TEMPERATURE DEVICES Parameter Description Test Conditions Min Max Unit 0.8 V VIL Input LOW Voltage VIH Input HIGH Voltage IIL Input LOW Current VIN = 0 V 50.0 A IIH Input HIGH Current VIN = VDD 100.0 A VOL Output LOW Voltage IOL = 8 mA (−1, −2, −3, −4) IOL = 12 mA (−1H, −5H) 0.4 V VOH Output HIGH Voltage IOH = −8 mA (−1, −2, −3, −4) IOH = −12 mA (−1H, −5H) IDD Supply Current (Note 7) Unloaded outputs 100 MHz REF −2, −3, −4 49 mA Select inputs at VDD or GND −1H, −5H 60 mA Unloaded outputs, 66 MHz REF (−1, −2, −3, −4) 34 mA Unloaded outputs, 33 MHz REF (−1, −2, −3, −4) 18 mA 2.0 7. Supply currents are measured for PLL−Bypass Mode (S2 = 1, S1 = 0). http://onsemi.com 4 V 2.4 V NB2308A Table 7. SWITCHING CHARACTERISTICS FOR COMMERCIAL AND INDUSTRIAL TEMPERATURE DEVICES Parameter Description Test Conditions Min Typ Unit 100 133.3 133.3 MHz % t1 Output Frequency 30 pF load (all devices) 15 pF load (−1H, −5H) 15 pF load (−1, −2, −3, −4) t1 Duty Cycle = (t2 / t1) * 100 (all devices) Measured at 1.4 V, FOUT = < 66.66 MHz 30 pF load 40.0 50.0 60.0 Measured at 1.4 V, FOUT = < 50 MHz 15 pF load 45.0 50.0 55.0 t3 Output Rise Time (−1, −2, −3, −4) 15 15 15 Max ns Measured between 0.8 V and 2.0 V 30 pF load 2.20 Measured between 0.8 V and 2.0 V 15 pF load 1.50 Output Rise Time (−1H, −5H) Measured between 0.8 V and 2.0 V 30 pF load 1.50 Output Fall Time (−1, −2, −3, −4) Measured between 2.0 V and 0.8 V 30 pF load 2.20 Measured between 0.8 V and 2.0 V 15 pF load 1.50 Output Fall Time (−1H, −5H) Measured between 2.0 V and 0.8 V 30 pF load 1.25 Output−to−Output Skew on same Bank (−1, −2, −3, −4) All outputs equally loaded 200 Output−to−Output Skew (−1H, −5H) All outputs equally loaded 200 Output Bank A−to−Output Bank B Skew (−1, −4, −5H) All outputs equally loaded 200 Output Bank A−to−Output Bank B Skew (−2, −3) All outputs equally loaded 400 t6 Delay, REF Rising Edge to FBK Rising Edge Measured at VDD/2 0 ±250 ps t7 Device−to−Device Skew Measured at VDD/2 on the FBK pins of the device 0 700 ps tJ Cycle−to−Cycle Jitter (−1, −1H, −4, −5H) Measured at 66.67 MHz, loaded outputs, 15 pF load 200 ps Measured at 66.67 MHz, loaded outputs, 30 pF load 200 Measured at 133.3 MHz, loaded outputs 15 pF load 100 Measured at 66.67 MHz, loaded outputs, 30 pF load 400 Measured at 66.67 MHz, loaded outputs, 15 pF load 400 Stable power supply, valid clock presented on REF and FBK pins 1.0 t4 t5 Cycle−to−Cycle Jitter (−2, −3) tLOCK PLL Lock Time http://onsemi.com 5 ns ps ms NB2308A Zero Delay and Skew Control To close the feedback loop of the NB2308A, the FBK pin can be driven from any of the eight available output pins. The output driving the FBK pin will be driving a total load of 7 pF plus any additional load that it drives. The relative loading of this output (with respect to the remaining outputs) can adjust the input−output delay. This is shown in Figure 3. For applications requiring zero input−output delay, all outputs including the one providing feedback should be equally loaded. If input−output delay adjustments are required, use the above graph to calculate loading differences between the feedback output and remaining outputs. For zero output−output skew, be sure to load outputs equally. All outputs should be uniformly loaded to achieve Zero Delay between input and output. REF INPUT TO CLKA/CLKB DELAY (ps) 1500 1000 500 0 −500 −1000 −1500 −30 −25 −20 −15 −10 −5 0 5 10 15 20 25 30 OUTPUT LOAD DIFFERENCE: FBK LOAD − CLKA/CLKB LOAD (pF) Figure 3. REF Input to CLKA/CLKB Delay vs. Difference in Loading between FBK Pin and CLKA/CLKB Pins SWITCHING WAVEFORMS t1 t2 1.4 V 1.4 V 0.8 V 0.8 V OUTPUT t3 Figure 4. Duty Cycle Timing OUTPUT 0V t4 Figure 5. All Outputs Rise/Fall Time 1.4 V V DD 2 INPUT 1.4 V OUTPUT 3.3 V 2.0 V 2.0 V 1.4 V V DD 2 OUTPUT t6 t5 Figure 6. Output − Output Skew Figure 7. Input − Output Propagation Delay V DD 2 FBK_Device 1 V DD 2 FBK_Device 2 t7 Figure 8. Device − Device Skew http://onsemi.com 6 NB2308A TEST CIRCUITS VDD VDD 0.1 F OUTPUTS VDD CLKOUT 0.1 F CLOAD OUTPUTS 1 k VDD 0.1 F 1 k 10 pF VDD GND 0.1 F GND Figure 9. Test Circuit #1 GND GND Figure 10. Test Circuit #2 For parameter t8 (output slew rate) on −1H devices BLOCK DIAGRAMS FBK FBK CLKA1 CLKA1 CLKA2 CLKA2 REF PLL REF MUX PLL MUX CLKA3 CLKA3 S2 SELECT INPUT DECODING SELECT INPUT DECODING S1 CLKA4 S2 CLKA4 S1 B2 CLKB1 CLKB1 CLKB2 CLKB2 CLKB3 CLKB3 CLKB4 CLKB4 Figure 11. NB2308Ax1 and NB2308Ax1H Figure 12. NB2308Ax2 http://onsemi.com 7 NB2308A BLOCK DIAGRAMS FBK FBK B2 CLKA1 B2 CLKA1 CLKA2 REF PLL CLKA2 MUX CLKA3 REF PLL MUX CLKA3 CLKA4 S2 CLKA4 S2 SELECT INPUT DECODING SELECT INPUT DECODING B2 S1 S1 CLKB1 CLKB1 CLKB2 CLKB2 CLKB3 CLKB3 CLKB4 CLKB4 Figure 13. NB2308Ax3 Figure 14. NB2308Ax4 FBK CLKA1 CLKA2 REF B2 PLL MUX CLKA3 CLKA4 S2 SELECT INPUT DECODING S1 CLKB1 CLKB2 CLKB3 CLKB4 Figure 15. NB2308Ax5H http://onsemi.com 8 NB2308A ORDERING INFORMATION Marking Operating Range Package Shipping† NB2308AC1DG 2308AC1G Commercial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AC1DR2G 2308AC1G Commercial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AI1DG 2308AI1G Industrial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AI1DR2G 2308AI1G Industrial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AC1HDG 2308AC1HG Commercial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AC1HDR2G 2308AC1HG Commercial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AI1HDG 2308AI1HG Industrial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AI1HDR2G 2308AI1HG Industrial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AC1DTG 2308AC1 Commercial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AC1DTR2G 2308AC1 Commercial TSSOP−16 (Pb−Free) 2500 Tape & Reel NB2308AI1DTG 2308AI1 Industrial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AI1DTR2G 2308AI1 Industrial TSSOP−16 (Pb−Free) 2500 Tape & Reel NB2308AC1HDTG 2308AI1H Commercial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AC1HDTR2G 2308AI1H Commercial TSSOP−16 (Pb−Free) 2500 Tape & Reel NB2308AI1HDTG 2308AI1H Industrial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AI1HDTR2G 2308AI1H Industrial TSSOP−16 (Pb−Free) 2500 Tape & Reel NB2308AC2DG 2308AC2G Commercial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AC2DR2G 2308AC2G Commercial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AI2DG 2308AI2G Industrial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AI2DR2G 2308AI2G Industrial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AC2DTG 2308AC2 Commercial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AC2DTR2G 2308AC2 Commercial TSSOP−16 (Pb−Free) 2500 Tape & Reel NB2308AI2DTG 2308AI2 Industrial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AI2DTR2G 2308AI2 Industrial TSSOP−16 (Pb−Free) 2500 Tape & Reel Device Availability Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 9 NB2308A ORDERING INFORMATION Marking Operating Range Package Shipping† NB2308AC3DG 2308AC3G Commercial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AC3DR2G 2308AC3G Commercial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AI3DG 2308AI3G Industrial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AI3DR2G 2308AI3G Industrial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AC3DTG 2308AC3 Commercial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AC3DTR2G 2308AC3 Commercial TSSOP−16 (Pb−Free) 2500 Tape & Reel NB2308AI3DTG 2308AI3 Industrial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AI3DTR2G 2308AI3 Industrial TSSOP−16 (Pb−Free) 2500 Tape & Reel NB2308AC4DG 2308AC4G Commercial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AC4DR2G 2308AC4G Commercial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AI4DG 2308AI4G Industrial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AI4DR2G 2308AI4G Industrial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AC4DTG 2308AC4 Commercial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AC4DTR2G 2308AC4 Commercial TSSOP−16 (Pb−Free) 2500 Tape & Reel NB2308AI4DTG 2308AI4 Industrial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AI4DTR2G 2308AI4 Industrial TSSOP−16 (Pb−Free) 2500 Tape & Reel NB2308AC5HDG 2308AC5HG Commercial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AC5HDR2G 2308AC5HG Commercial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AI5HDG 2308AI5HG Industrial SOIC−16 (Pb−Free) 48 Units / Rail NB2308AI5HDR2G 2308AI5HG Industrial SOIC−16 (Pb−Free) 2500 Tape & Reel NB2308AC5HDTG 2308AC5H Commercial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AC5HDTR2G 2308AC5H Commercial TSSOP−16 (Pb−Free) 2500 Tape & Reel NB2308AI5HDTG 2308AI5H Industrial TSSOP−16 (Pb−Free) 96 Units / Rail NB2308AI5HDTR2G 2308AI5H Industrial TSSOP−16 (Pb−Free) 2500 Tape & Reel Device Availability Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now Now †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 10 NB2308A PACKAGE DIMENSIONS TSSOP−16 CASE 948F−01 ISSUE A 16X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S K ÉÉ ÇÇ ÇÇ ÉÉ ÇÇ ÉÉ K1 2X L/2 16 9 J1 B −U− L SECTION N−N J PIN 1 IDENT. 8 1 N 0.15 (0.006) T U S 0.25 (0.010) A −V− M N F DETAIL E −W− C 0.10 (0.004) −T− SEATING PLANE D G H DETAIL E http://onsemi.com 11 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 −−− 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 −−− 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ NB2308A PACKAGE DIMENSIONS SOIC−16 CASE 751B−05 ISSUE J −A− 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 −B− 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 _ C −T− SEATING PLANE J M D 16 PL 0.25 (0.010) M T B S A S DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.229 0.244 0.010 0.019 Licensed under US patent Nos 5,488,627, 6,646,463 and 5,631,920. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 12 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NB2308A/D