Revised January 2001 NC7SZ175 TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear General Description Features The NC7SZ175 is a single positive edge-triggered D-type CMOS Flip-Flop with Asynchronous Clear from Fairchild’s Ultra High Speed Series of TinyLogic in the space saving SC70 6-lead package. The device is fabricated with advanced CMOS technology to achieve ultra high speed with high output drive while maintaining low static power dissipation over a very broad VCC operating range. The device is specified to operate over the 1.65V to 5.5V VCC range. The inputs and output are high impedance when VCC is 0V. Inputs tolerate voltages up to 7V independent of VCC operating voltage. This single flip-flop will store the state of the D input that meets the setup and hold time requirements on the LOW-to-HIGH Clock (CP) transition. A LOW input to Clear sets the Q output to LOW level. The Clear input is independent of clock. ■ Space saving SC70 6-lead package ■ Ultra High Speed; tPD 2.6 ns Typ into 50 pF at 5V VCC ■ High Output Drive; ±24 mA at 3V VCC ■ Broad VCC Operating Range; 1.65V to 5.5V ■ Matches the performance of LCX when operated at 3.3V VCC ■ Power down high impedance inputs/output ■ Overvoltage tolerant inputs facilitate 5V to 3V translation ■ Patented noise/EMI reduction circuitry implemented Ordering Code: Order Package Product Code Number Number Top Mark NC7SZ175P6 MAA06A Z75 6-Lead SC70, EIAJ SC88, 1.25mm Wide 250 Units on Tape and Reel NC7SZ175P6X MAA06A Z75 6-Lead SC70, EIAJ SC88, 1.25mm Wide 3k Units on Tape and Reel Package Description Function Table Logic Symbol Inputs CP D X H = HIGH Logic Level L = LOW Logic Level Supplied As Output C IEEE/IEC Q L H L H H H X H Qn X L L Connection Diagrams Qn = No change in data X = Immaterial Z = HIGH Impedance Pin Descriptions Pin Names D CP (Top View) Description Data Input Pin One Orientation Diagram Clock Pulse Input C Clear Input Q Flip-Flop Output AAA represents Product Code Top Mark - see ordering code Note: Orientation of Top Mark determines Pin One location. Read the top product code mark left to right, Pin One is the lower left pin (see diagram). TinyLogic is a trademark of Fairchild Semiconductor Corporation. © 2001 Fairchild Semiconductor Corporation DS500158 www.fairchildsemi.com NC7SZ175 TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear May 1998 NC7SZ175 Absolute Maximum Ratings(Note 1) Supply Voltage (VCC) −0.5V to +7.0V DC Input Voltage (VIN) −0.5V to +7.0V DC Output Voltage (VOUT) −0.5V to +7.0V Recommended Operating Conditions (Note 2) Power Supply DC Input Diode Current (IIK) VIN < 0V −50 mA DC Output Diode Current (IOK) VOUT < 0V −50 mA Operating (VCC) 1.65V to 5.5V Data Retention 1.5V to 5.5V Input Voltage (VIN) 0V to 5.5V Output Voltage (VOUT) 0V to VCC Input Rise and Fall Time (tr, tf) DC Output (IOUT) Source/Sink Current ±50 mA VCC = 1.8V, 2.5V ± 0.2V 0 to 20 ns/V DC VCC/GND Current (ICC/IGND) ±50 mA VCC = 3.3V ± 0.3V 0 to 10 ns/V −65°C to +150°C VCC= 5.5V ± 0.5V Storage Temperature Range (TSTG) 150°C Junction Temperature under Bias (TJ) 0 to 5 ns/V −40°C to +85°C Operating Temperature (TA) Thermal Resistance (θJA) Junction Lead Temperature (TL) 260°C (Soldering, 10 seconds) Power Dissipation (PD) @+85°C 350 ° C/W Note 1: The “Absolute Maximum Ratings”: are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table will define the conditions for actual device operation. 180 mW Note 2: Unused inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics Symbol Parameter (V) VIH HIGH Level Control Input Voltage VIL LOW Level Control Input Voltage VOH VOL TA = +25°C VCC Min Typ TA = −40°C to +85°C Max 1.65 to 1.95 0.75 VCC 2.3 to 5.5 Min 0.75 VCC 0.7 VCC 1.65 to 1.95 0.25 VCC 0.25 VCC 2.3 to 5.5 0.3 VCC 0.3 VCC 1.65 1.55 1.65 Output Voltage 1.8 1.7 1.8 1.7 2.3 2.2 2.3 2.2 3.0 2.9 3.0 2.9 IOH = −100 µA 4.4 4.5 4.4 1.24 1.52 1.29 2.3 1.9 2.15 1.9 IOH = −8 mA 3.0 2.4 2.8 2.4 IOH = −16 mA 3.0 2.3 2.68 2.3 IOH = −24 mA 4.5 3.8 4.2 3.8 V 0.1 Output Voltage 1.8 0.0 0.1 0.1 2.3 0.0 0.1 0.1 3.0 0.0 0.1 0.1 IOFF Power Off Leakage Current Quiescent Supply Current www.fairchildsemi.com or VIL IOH = −4 mA IOH = −32 mA 0.0 ICC VIN = VIH 4.5 1.65 1.65 Input Leakage Current V 1.55 LOW Level Control IIN Conditions V 0.7 VCC HIGH Level Control Unit Max 0.1 IOL = 100 µA VIN = VIL 4.5 0.0 0.1 0.1 1.65 0.08 0.24 0.24 2.3 0.10 0.3 0.3 IOL = 8 mA 3.0 0.15 0.4 0.4 IOL = 16 mA 3.0 0.22 0.55 0.55 IOL = 24 mA 4.5 0.22 0.55 0.55 ±0.1 ±1.0 µA 0 ≤ VIN ≤ 5.5V 0 to 5.5 V or VIH IOL = 4 mA IOL = 32 mA 0.0 1.0 10 µA VIN or VOUT = 5.5V 1.65 to 5.5 1.0 10.0 µA VIN = 5.5V, GND 2 Symbol (V) Maximum Clock fMAX TA = +25°C VCC Parameter Min Typ TA = −40°C to +85°C Max 1.65 Frequency Min Max Units Conditions Fig. No. 100 1.8 100 2.5 ± 0.2 125 3.3 ± 0.3 150 5.0 ± 0.5 MHz CL = 50 pF RL = 500 Ω Figures 1, 4 175 tPLH Propagation Delay 1.65 2.5 9.8 15.0 2.5 16.5 tPHL CP to Q 1.8 2.5 6.5 10.0 2.5 11.0 2.5 ± 0.2 2.0 3.8 6.5 2.0 7.0 3.3 ± 0.3 1.5 2.8 4.5 1.4 5.0 5.0 ± 0.5 1.0 2.2 3.5 1.0 3.8 3.3 ± 0.3 2.0 3.4 5.5 1.6 6.2 CL = 50 pF 5.0 ± 0.5 1.5 2.6 4.0 1.4 4.7 RL = 500 Ω Figures 1, 3 Propagation Delay 1.65 2.5 9.8 13.5 2.5 15.0 C to Q 1.8 2.5 6.5 9.0 2.5 10.0 2.5 ± 0.2 2.0 3.8 6.0 2.0 6.4 CL = 15 pF 3.3 ± 0.3 Figures 1, 3 1.5 2.8 4.3 1.2 4.6 5.0 ± 0.5 1.5 2.2 3.2 1.0 3.5 3.3 ± 0.3 1.5 3.4 5.3 1.5 5.8 CL = 50 pF 5.0 ± 0.5 1.0 2.7 4.0 1.2 4.5 RL = 500 Ω tPHL tS tH Setup Time 2.5 ± 0.2 2.5 CP to D 3.3 ± 0.3 2.0 5.0 ± 0.5 1.5 Hold Time, 2.5 ± 0.2 1.5 CP to D 3.3 ± 0.3 1.5 5.0 ± 0.5 1.5 2.5 ± 0.2 3.0 3.3 ± 0.3 2.8 5.0 ± 0.5 2.5 2.5 ± 0.2 3.0 3.3 ± 0.3 2.8 5.0 ± 0.5 2.5 Recovery Time, 2.5 ± 0.2 1.0 C to CP 3.3 ± 0.3 1.0 5.0 ± 0.5 1.0 Pulse Width, CP tW Pulse Width, C trec CL = 15 pF ns ns RL = 1 MΩ RL = 1 MΩ CL = 50 pF ns RL = 500 Ω ns RL = 500 Ω CL = 50 pF CL = 50 pF ns RL = 500 Ω Figures 1, 3 Figures 1, 3 Figures 1, 4 Figures 1, 4 Figures 1, 4 Clock HIGH or LOW ns CL = 50 pF RL = 500 Ω CL = 50 pF ns RL = 500 Ω Figures 1, 4 Figures 1, 4 Capacitance (Note 3) Symbol Parameter Typ CIN Input Capacitance COUT Output Capacitance 4 CPD Power Dissipation Capacitance 10 (Note 4) 12 Max 3 Units Conditions pF VCC = Open, VIN = 0V or VCC pF VCC = 3.3V, VIN = 0V or VCC pF VCC = 3.3V VCC = 5.0V Note 3: TA = +25C, f = 1MHz. Note 4: CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle. (See Figure 2) CPD is related to ICCD dynamic operating current by the expression: ICCD = (CPD)(VCC)(fIN) + (ICCstatic). 3 www.fairchildsemi.com NC7SZ175 AC Electrical Characteristics NC7SZ175 AC Loading and Waveforms CL includes load and stray capacitance CP Input = AC Waveform; tr = tf = 1.8 ns; Input PRR = 1.0 MHz, tw = 500 ns CP Input PRR = 10 MHz; Duty Cycle = 50% D Input PRR = 5MHz; Duty Cycle = 50% FIGURE 1. AC Test Circuit FIGURE 2. ICCD Test Circuit FIGURE 3. AC Waveforms FIGURE 4. AC Waveforms www.fairchildsemi.com 4 TAPE FORMAT Package Designator Tape Number Cavity Section Cavities Status Status 125 (typ) Empty Sealed Leader (Start End) P6 P6X Carrier Cover Tape 250 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed Leader (Start End) 125 (typ) Empty Sealed 3000 Filled Sealed 75 (typ) Empty Sealed Carrier Trailer (Hub End) TAPE DIMENSIONS inches (millimeters) Package SC70-6 Tape Size 8 mm DIM A DIM B 0.093 0.096 (2.35) (2.45) DIM F DIM Ko 0.138 ± 0.004 0.053 ± 0.004 (3.5 ± 0.10) 5 (1.35 ± 0.10) DIM P1 DIM W 0.157 0.315 ± 0.004 (4) (8 ± 0.1) www.fairchildsemi.com NC7SZ175 Tape and Reel Specification NC7SZ175 Tape and Reel Specification (Continued) REEL DIMENSIONS inches (millimeters) Tape Size 8 mm A B C D N W1 W2 W3 7.0 0.059 0.512 0.795 2.165 0.331 + 0.059/−0.000 0.567 W1 + 0.078/−0.039 (177.8) (1.50) (13.00) (20.20) (55.00) (8.40 + 1.50/−0.00) (14.40) (W1 + 2.00/−1.00) www.fairchildsemi.com 6 NC7SZ175 TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear Physical Dimensions inches (millimeters) unless otherwise noted 6-Lead SC70, EIAJ SC88, 1.25mm Wide Package Number MAA06A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 7 www.fairchildsemi.com