Test Coils For Reed Switches and Sensors Cylindrical Test Coil No. A B C D E Wire Diameter Turns Coil Res. Rectangular Test Coil A mm B mm C mm D mm E mm F mm G mm H mm Wire Diameter mm Turns Coil Resistance 717 102 001 53.3 50.8 7.6 5.6 14.1 0.090 10000 845 717 102 002 717 102 003 21.0 12.0 19.0 10.0 4.3 3.3 3.4 2.3 7.7 11.0 0.050 0.060 5000 5000 740 600 All dimensions in mm TCP 3001 13.5 7 8 6 14 18 12 10 0.05 5000 2000 TCP3002 23.3 19.7 6.8 6.2 14.8 20.6 12.2 11.6 0.08 10000 1900 717 102 004 27.8 25.4 8.7 2.4 17.2 0.100 5000 404 TCP 3003 42.5 36.5 14.8 13.8 25.0 28.6 14.6 13.6 0.15 5000 290 717 102 005 19.0 15.0 3.7 2.9 11.0 0.071 5000 450 TCP 3004 42.5 36.5 15.8 13.8 25.0 35.6 22.8 20.8 0.15 5000 440 Due to continual improvement, specifications are subject to change without notice www.reed-sensor.com 6 December 2004 s Reed Relays and Electronics India Limited [email protected] Tel 91-44-6528-4022 Standard Magnets For Reed Switches and Sensors Cylindrical Magnets mm Part Number Material D (mm) L (mm) NDC-T NdFeB:N35 2.0 4.0 NDC-S NdFeB:N35 3.0 7.0 NDC-M NdFeB:N35 4.0 10.0 NDC-L NdFeB:N35 8.0 15.0 Bar Magnets mm Part Number Material L (mm) B (mm) H (mm) NDR-T NdFeB:N35 4.0 1.5 1.5 NDR-S NdFeB:N35 6.0 2.5 2.5 NDR-M NdFeB:N35 8.0 3.0 3.0 NDR-L NdFeB:N35 19.0 4.0 4.0 Magnet Material Specifications Magnet Type Composition Ferrite AlNiCo NdFeB NdFeB SmCo Code C8 LNG37 N35 N35SH YX20 Remanance Br (mT) 385 1180 1180 1180 925 Coercivity HcB (kA/m) 235 48 880 880 680 HcJ (kA/m) 242 53 955 1353 1595 Energy Product max. BH (kJ/m3) 27.8 37 270 270 160 Operating Temperature (C) 300 550 80 120 300 Due to continual improvement, specifications are subject to change without notice www.reed-sensor.com 30 August 2006 s Reed Relays and Electronics India Limited [email protected] Tel 91-44-6528-4022 Restriction of Hazardous Substances RoHS Compliance In late 2002 the European Parliament approved two directives related to the reduction of electrical and electronic waste, namely the Waste Electrical and Electronic Equipment (WEEE) and Restriction of the use of certain Hazardous Substances (RoHS) Directives. The WEEE Directive aims to regulate the reuse, recycling and recovery of waste electrical and electronic equipment; the ultimate goal is to prevent the disposal of this waste. In the RoHS Directive, the use of the aforementioned substances in most electrical and electronic equipment will be banned or severely restricted. The RoHS Directive calls for the elimination of these substances from most electronic equipment starting 1 July 2006. Our products are SGS certified for the RoHS compliant levels of Lead, Mercury, Cadmium and Hexalent Chromium. End-of-Life Vehicle (ELV) End-of-Life Vehicle (ELV) regulations set limits for the following substances: Lead Mercury Cadmium Hexavalent Chromium Restriction of Hazardous Substances (RoHS) The Reduction of Hazardous Substances (RoHS) regulations set limits for the following substances: Lead Mercury Cadmium Hexavalent Chromium Polybrominated Biphenyls (PBB) Polybrominated Diphenyl Ethers (PBDE) To certify to the above compliances, these substances must not be intentionally added to the product AND cannot exceed the following maximum allowable levels as a trace substance: 0.1% (1,000 ppm) for: Lead*, Mercury, Hexavalent Chromium, PBB and PBDE 0.01% (100 ppm) for: Cadmium *Lead as an alloying element in copper alloys is allowed up to 4.0% (40,000 ppm); in steel up to 0.35% (3,500 ppm) is allowed; in aluminum alloys up to 0.40% (4,000 ppm) is allowed. These requirements must be applied at the homogeneous material level. Since RoHS compliance is a stricter standard than ELV compliance, parts that are RoHS compliant are also ELV compliant. Due to continual improvement, specifications are subject to change without notice www.reed-sensor.com 20 January 2009 s Reed Relays and Electronics India Limited [email protected] Tel 91-44-6528-4022 Magnet Sensor Usage Notes Magnet Sensors are delicate products. Handle with extra care. Do’s When switching inductive or capacitive loads, use contact protection circuits. Don’ts Do not use ferro-magnetic mounting parts, screws, or other ferro-magnetic devices nearby. This will affect the sensitivity (AT). When manual soldering, do not subject to more than a 5 second dwell. This may cause damage to the seals, change sensitivity, and reduce solderability. Do not drop. Dropping or subjection to shock will permanently damage the contact or alter the sensitivity (AT). Switching voltage, switching current, and contact rating should not exceed maximum limits stated in specification sheets. Due to continual improvement, specifications are subject to change without notice www.reed-sensor.com 26 May 2004 s Reed Relays and Electronics India Limited [email protected] Tel 91-44-6528-4022