NTE726 Integrated Circuit Wide Band Amplifier Features: D Exceptionally High Amplifier Gain: Power Gain at 4.5MHz/s – 75dB (Typ) D Excellent Limiting Characteristics: Input Limiting Voltage (Knee) = 600µV (Typ) at 10.7MHz/s D Wide Frequency Capability: 100kHz/s to > 20MHz/s Absolute Maximum Ratings: (TA = +25°C unless otherwise specified) Recommended Minimum DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5V Minimum Input Signal Voltage (Between Pin1 and Pin2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±3V Maximum Device Dissipation, PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300mW Operating Temperature Range, Topr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55° to +125°C Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65° to +150°C Lead Temperature (During Soldering, 1/16” from case, 10sec max), TL . . . . . . . . . . . . . . . . . +265°C Electrical Characteristics: (TA = +25°C unless otherwise specified) Parameter Total Device Dissipation Voltage Gain Symbol PT A Test Conditions Min Typ Max Unit VCC = 6V, Note 1 66 90 121 mW VCC = 7.5V, Note 1 97 120 167 mW VCC = 10V, Note 1 150 190 255 mW VCC = 6V, f = 1Mc/s, Note 2 60 66 – dB VCC = 7.5V, f = 1Mc/s, Note 2 65 70 – dB VCC = 7.5V, f = 4.5Mc/s, Note 2 60 67 – dB VCC = 7.5V, f = 10.7Mc/s, Note 2 55 61 – dB VCC = 10V, f = 1Mc/s, Note 2 65 71 – dB VCC = 7.5V, f = 4.5Mc/s – 3 – kΩ – 7 – pF – 31.5 – kΩ – 4.2 – pF Input–Impedance Components Parallel Input Resistance RIN Parallel Input Capacitance CIN Output–Impedance Components Parallel Output Resistance ROUT Parallel Output Capacitance COUT Noise Figure Input Limiting Voltage (Knee) VCC = 7.5V, f = 4.5Mc/s NF VCC = 7.5V, f = 4.5Mc/s – 8.7 – dB vi(lim) VCC = 7.5V, f = 4.5Mc/s – 300 400 µV Note 1. The total current drain may be determined by dividing PT by VCC. Note 2. Recommended minimum DC supply voltage (VCC) is 5.5V. Nominal load current flowing into Pin5 is 1.5mA at 7.5V. Pin Connection Diagram (Top View) Internal Connection* 6 7 GND Internal Connection* 5 8 Internal Connection* 9 IF Output 4 10 Bypass 3 Bypass VCC 1 2 IF Input High IF Input Reference *NOTE: These leads are internally connected. DO NOT USE. .335 (8.52) Dia Max .175 (4.45) Max .500 (12.7) Min .018 (0.45) Dia Typ .100 (2.54) 4 3 2 5 6 1 .370 (9.4) Max 7 10 9 8 .200 (5.08) Dia