NX3L4357 Low-ohmic single-pole triple-throw analog switch with enable input Rev. 4 — 7 November 2011 Product data sheet 1. General description The NX3L4357 is a low-ohmic single-pole triple-throw analog switch suitable for use as an analog or digital 3:1 multiplexer/demultiplexer. It has two digital select inputs (S0 and S1), one digital enable input (E), three independent inputs/outputs (Y0, Y1 and Y2) and a common input/output (Z). The device features a broadcast mode, when S0 and S1 are both high the signal applied to pin Z is passed to Y0, Y1 and Y2. Schmitt trigger action at the digital inputs makes the circuit tolerant to slower input rise and fall times. Low threshold digital inputs allows this device to be driven by 1.8 V logic levels in 3.3 V applications without significant increase in supply current ICC. This makes it possible for the NX3L4357 to switch 4.3 V signals with a 1.8 V digital controller, eliminating the need for logic level translation. The NX3L4357 allows signals with amplitude up to VCC to be transmitted from Z to Yn or Yn to Z. Its low ON resistance (0.5 ) and flatness (0.13 ) ensures minimal attenuation and distortion of transmitted signals. 2. Features and benefits Wide supply voltage range from 1.4 V to 4.3 V Very low ON resistance (peak): 1.65 (typical) at VCC = 1.4 V 0.95 (typical) at VCC = 1.65 V 0.55 (typical) at VCC = 2.3 V 0.50 (typical) at VCC = 2.7 V 0.50 (typical) at VCC = 4.3 V Break-before-make switching High noise immunity ESD protection: HBM JESD22-A114F Class 3A exceeds 7500 V MM JESD22-A115-A exceeds 200 V CDM AEC-Q100-011 revision B exceeds 1000 V IEC61000-4-2 contact discharge exceeds 6000 V for switch ports CMOS low-power consumption Latch-up performance exceeds 100 mA per JESD 78B Class II Level A 1.8 V control logic at VCC = 3.6 V Control input accepts voltages above supply voltage Very low supply current, even when input is below VCC High current handling capability (350 mA continuous current under 3.3 V supply) Specified from 40 C to +85 C and from 40 C to +125 C NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 3. Applications Cell phone PDA Portable media player 4. Ordering information Table 1. Ordering information Type number NX3L4357GM Package Temperature range Name Description Version 40 C to +125 C XQFN10U plastic extremely thin quad flat package; no leads; 10 terminals; UTLP based; body 2 1.55 0.5 mm SOT1049-2 5. Marking Table 2. Marking Type number Marking code NX3L4357GM D43 6. Functional diagram Y0 S0 Y1 DECODER S1 S0 Y0 S1 Y1 Y2 Y2 E E Z Z 001aak764 001aak763 Fig 1. Logic symbol NX3L4357 Product data sheet Fig 2. Logic diagram All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 2 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 7. Pinning information 7.1 Pinning 10 VCC NX3L4357 Y0 2 8 Y1 Z 3 7 Y2 E 4 6 n.c. S1 GND 1 5 9 S0 001aak765 Transparent top view Fig 3. Pin configuration SOT1049-2 (XQFN10U) 7.2 Pin description Table 3. Pin description Symbol Pin Description S0 1 select input S1 2 select input Z 3 common output or input E 4 enable input (active LOW) GND 5 ground (0 V) n.c. 6 not connected Y2 7 independent input or output Y1 8 independent input or output Y0 9 independent input or output VCC 10 supply voltage NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 3 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 8. Functional description Table 4. Function table[1] E S1 S0 Channel on L L L Y0 = Z L L H Y1 = Z L H L Y2 = Z L H H Y0, Y1, Y2 = Z (broadcast mode) H X X switches off [1] H = HIGH voltage level; L = LOW voltage level; X = don’t care. 9. Limiting values Table 5. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V). Symbol Parameter VCC supply voltage VI input voltage VSW switch voltage IIK input clamping current VI < 0.5 V ISK switch clamping current ISW switch current Tstg Conditions Min total power dissipation Unit 0.5 +4.6 V [1] 0.5 +4.6 V [2] 0.5 VCC + 0.5 V 50 - mA VI < 0.5 V or VI > VCC + 0.5 V - 50 mA VSW > 0.5 V or VSW < VCC + 0.5 V; source or sink current - 350 mA VSW > 0.5 V or VSW < VCC + 0.5 V; pulsed at 1 ms duration, < 10 % duty cycle; peak current - 500 mA 65 +150 C - 250 mW select input S0, S1 and E storage temperature Ptot Max Tamb = 40 C to +125 C [3] [1] The minimum input voltage rating may be exceeded if the input current rating is observed. [2] The minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not exceed 4.6 V. [3] For XQFN10U packages: above 132 C the value of Ptot derates linearly with 14.1 mW/K. NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 4 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 10. Recommended operating conditions Table 6. Recommended operating conditions Symbol Parameter VCC supply voltage VI input voltage Conditions select input S0, S1 and E VSW switch voltage Tamb ambient temperature t/V input transition rise and fall rate [1] switch input Y0, Y1 and Y2 [2] VCC = 1.4 V to 4.3 V Min Max Unit 1.4 4.3 V 0 4.3 V 0 VCC V 40 +125 C - 200 ns/V [1] To avoid sinking GND current from terminal Z when switch current flows in terminal Yn, the voltage drop across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal Z, no GND current will flow from terminal Yn. In this case, there is no limit for the voltage drop across the switch. [2] Applies to select input Sn signal levels. 11. Static characteristics Table 7. Static characteristics At recommended operating conditions; voltages are referenced to GND (ground 0 V). Symbol Parameter VIH VIL HIGH-level input voltage LOW-level input voltage Tamb = 25 C Conditions Typ Max Min Max Max (85 C) (125 C) VCC = 1.4 V to 1.6 V 0.9 - - 0.9 - - V 0.9 - - 0.9 - - V VCC = 2.3 V to 2.7 V 1.1 - - 1.1 - - V VCC = 2.7 V to 3.6 V 1.3 - - 1.3 - - V VCC = 3.6 V to 4.3 V 1.4 - - 1.4 - - V VCC = 1.4 V to 1.6 V - - 0.3 - 0.3 0.3 V VCC = 1.65 V to 1.95 V - - 0.4 - 0.4 0.3 V VCC = 2.3 V to 2.7 V - - 0.5 - 0.5 0.4 V VCC = 2.7 V to 3.6 V - - 0.5 - 0.5 0.5 V VCC = 3.6 V to 4.3 V - - 0.6 - 0.6 0.6 V - - - - 0.5 1 A VCC = 1.4 V to 3.6 V - - 5 - 10 100 nA VCC = 3.6 V to 4.3 V - - 10 - 50 200 nA VCC = 1.4 V to 3.6 V - - 5 - 20 200 nA VCC = 3.6 V to 4.3 V - - 10 - 50 400 nA VCC = 3.6 V - - 100 - 300 3000 nA VCC = 4.3 V - - 150 - 500 5000 nA input leakage current select input S0, S1 and E; VI = GND to 4.3 V; VCC = 1.4 V to 4.3 V IS(OFF) OFF-state leakage current port Y0, Y1 and Y2; see Figure 4 ON-state leakage current Z port; see Figure 5 ICC Min Unit VCC = 1.65 V to 1.95 V II IS(ON) Tamb = 40 C to +125 C supply current VI = VCC or GND; VSW = GND or VCC NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 5 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input Table 7. Static characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground 0 V). Symbol Parameter ICC Tamb = 25 C Conditions Tamb = 40 C to +125 C Unit Min Typ Max Min Max Max (85 C) (125 C) additional VSW = GND or VCC supply current VI = 2.6 V; VCC = 4.3 V - 2.0 4.0 - 7 7 A VI = 2.6 V; VCC = 3.6 V - 0.35 0.7 - 1 1 A VI = 1.8 V; VCC = 4.3 V - 7.0 10.0 - 15 15 A VI = 1.8 V; VCC = 3.6 V - 2.5 4.0 - 5 5 A VI = 1.8 V; VCC = 2.5 V - 50 200 - 300 500 nA - 1.0 - - - - pF CI input capacitance CS(OFF) OFF-state capacitance port Y0, Y1 and Y2 - 35 - - - - pF CS(ON) ON-state capacitance port Z; broadcast mode - 330 - - - - pF port Y0, Y1 and Y2 - 170 - - - - pF 11.1 Test circuits VCC Sn VIL or VIH Z Yn IS E VI VIH VO GND 001aak766 VI = 0.3 V or VCC 0.3 V; VO = VCC 0.3 V or 0.3 V. Fig 4. Test circuit for measuring OFF-state leakage current VCC Sn VIL or VIH Yn Z IS E VI VO VIL GND 001aak767 VI = 0.3 V or VCC 0.3 V; VO = VCC 0.3 V or 0.3 V. Fig 5. Test circuit for measuring ON-state leakage current NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 6 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 11.2 ON resistance Table 8. ON resistance At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for graphs see Figure 7 to Figure 13. Symbol Parameter Tamb = 40 C to +85 C Conditions Min RON(peak) ON resistance (peak) Min Max VCC = 1.4 V - 1.6 3.7 - 4.1 VCC = 1.65 V - 1.0 1.6 - 1.7 VCC = 2.3 V - 0.55 0.8 - 0.9 VCC = 2.7 V - 0.5 0.75 - 0.9 - 0.5 0.75 - 0.9 VCC = 1.4 V - 0.20 0.35 - 0.35 VCC = 1.65 V - 0.20 0.25 - 0.30 VCC = 2.3 V - 0.09 0.13 - 0.15 VCC = 2.7 V - 0.09 0.13 - 0.15 - 0.09 0.13 - 0.15 VCC = 1.4 V - 1.05 3.35 - 3.65 VCC = 1.65 V - 0.55 1.25 - 1.35 VCC = 2.3 V - 0.20 0.35 - 0.40 VCC = 2.7 V - 0.18 0.35 - 0.40 VCC = 4.3 V - 0.23 0.40 - 0.45 ON resistance mismatch VI = GND to VCC; between channels ISW = 100 mA [2] VCC = 4.3 V RON(flat) Max Tamb = 40 C to +125 C Unit port Y0, Y1 and Y2; VI = GND to VCC; ISW = 100 mA; see Figure 6 VCC = 4.3 V RON Typ[1] ON resistance (flatness) port Y0, Y1 and Y2; VI = GND to VCC; ISW = 100 mA [3] [1] Typical values are measured at Tamb = 25 C. [2] Measured at identical VCC, temperature and input voltage. [3] Flatness is defined as the difference between the maximum and minimum value of ON resistance measured at identical VCC and temperature. NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 7 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 11.3 ON resistance test circuit and graphs 001aag564 1.6 RON (Ω) 1.2 VSW V (1) 0.8 VCC (2) Sn VIL or VIH (3) Z Yn (4) 0.4 (5) (6) E VI ISW VIL 0 GND 0 1 2 RON = VSW / ISW. 3 4 5 VI (V) 001aak768 (1) VCC = 1.5 V. (2) VCC = 1.8 V. (3) VCC = 2.5 V. (4) VCC = 2.7 V. (5) VCC = 3.3 V. (6) VCC = 4.3 V. Measured at Tamb = 25 C. Fig 6. Test circuit for measuring ON resistance NX3L4357 Product data sheet Fig 7. Typical ON resistance as a function of input voltage (Yn port) All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 8 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 001aag565 1.6 001aag566 1.0 RON (Ω) RON (Ω) 0.8 1.2 (1) (2) (3) (4) 0.6 (1) (2) (3) (4) 0.8 0.4 0.4 0.2 0 0 0 1 2 3 0 1 2 VI (V) (1) Tamb = 125 C. (1) Tamb = 125 C. (2) Tamb = 85 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (3) Tamb = 25 C. (4) Tamb = 40 C. (4) Tamb = 40 C. Fig 8. ON resistance as a function of input voltage; VCC = 1.5 V (Yn port) 001aag567 1.0 3 VI (V) RON (Ω) Fig 9. ON resistance as a function of input voltage; VCC = 1.8 V (Yn port) 001aag568 1.0 RON (Ω) 0.8 0.8 0.6 0.6 (1) (2) (3) (4) 0.4 0.4 0.2 0.2 0 (1) (2) (3) (4) 0 0 1 2 3 0 VI (V) (1) Tamb = 125 C. (2) Tamb = 85 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (3) Tamb = 25 C. (4) Tamb = 40 C. (4) Tamb = 40 C. Fig 10. ON resistance as a function of input voltage; VCC = 2.5 V (Yn port) Product data sheet 2 3 VI (V) (1) Tamb = 125 C. NX3L4357 1 Fig 11. ON resistance as a function of input voltage; VCC = 2.7 V (Yn port) All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 9 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 001aag569 1.0 001aaj896 1.0 RON (Ω) RON (Ω) 0.8 0.8 0.6 0.6 (1) (2) (3) (4) 0.4 (1) (2) (3) (4) 0.4 0.2 0.2 0 0 0 1 2 3 4 0 1 2 3 4 VI (V) 5 VI (V) (1) Tamb = 125 C. (1) Tamb = 125 C. (2) Tamb = 85 C. (2) Tamb = 85 C. (3) Tamb = 25 C. (3) Tamb = 25 C. (4) Tamb = 40 C. (4) Tamb = 40 C. Fig 12. ON resistance as a function of input voltage; VCC = 3.3 V Fig 13. ON resistance as a function of input voltage; VCC = 4.3 V 12. Dynamic characteristics Table 9. Dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for test circuit see Figure 16. Symbol Parameter ten tdis enable time disable time Tamb = 25 C Conditions Product data sheet Unit Min Max Min Max (85 C) Max (125 C) VCC = 1.4 V to 1.6 V - 50 100 - 120 125 ns VCC = 1.65 V to 1.95 V - 36 75 - 85 95 ns VCC = 2.3 V to 2.7 V - 24 50 - 55 60 ns VCC = 2.7 V to 3.6 V - 22 45 - 45 50 ns VCC = 3.6 V to 4.3 V - 22 45 - 45 50 ns - 32 80 - 90 105 ns E, Sn to Z or Yn; see Figure 14 E, Sn to Z or Yn; see Figure 14 VCC = 1.4 V to 1.6 V NX3L4357 Tamb = 40 C to +125 C Typ[1] VCC = 1.65 V to 1.95 V - 20 65 - 70 75 ns VCC = 2.3 V to 2.7 V - 12 30 - 35 40 ns VCC = 2.7 V to 3.6 V - 10 25 - 30 35 ns VCC = 3.6 V to 4.3 V - 10 25 - 30 35 ns All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 10 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input Table 9. Dynamic characteristics …continued At recommended operating conditions; voltages are referenced to GND (ground = 0 V); for test circuit see Figure 16. Symbol Parameter tb-m Tamb = 25 C Conditions Tamb = 40 C to +125 C Unit Min Typ[1] Max Min Max (85 C) Max (125 C) - 19 - 9 - - ns VCC = 1.65 V to 1.95 V - 17 - 7 - - ns VCC = 2.3 V to 2.7 V - 13 - 4 - - ns VCC = 2.7 V to 3.6 V - 10 - 3 - - ns VCC = 3.6 V to 4.3 V - 10 - 2 - - ns [2] break-before-make see Figure 15 time VCC = 1.4 V to 1.6 V [1] Typical values are measured at Tamb = 25 C and VCC = 1.5 V, 1.8 V, 2.5 V, 3.3 V and 4.3 V respectively. [2] Break-before-make guaranteed by design. 12.1 Waveforms and test circuits VI Sn, E input VM VM GND ten VOH tdis VX output OFF to HIGH HIGH to OFF VX GND tdis VOH ten VX output HIGH to OFF OFF to HIGH VX GND 001aak769 Measurement points are given in Table 10. Logic level: VOH is typical output voltage level that occurs with the output load. Fig 14. Enable and disable times Table 10. Measurement points Supply voltage Input Output VCC VM VX 1.4 V to 4.3 V 0.5VCC 0.9VOH NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 11 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input VCC VIL or VIH Sn Z Yn E G VI V VO RL CL VEXT = 1.5 V VIL GND 001aak770 a. Test circuit VI 0.5VI 0.9VO 0.9VO VO tb-m 001aag572 b. Input and output measurement points VI may be connected to S0 or S1. Fig 15. Test circuit for measuring break-before-make timing VCC VIL or VIH Sn Z Yn E G VI V VO RL CL VEXT = 1.5 V VIL GND 001aak771 Test data is given in Table 11. VI may be connected to Sn or E. Definitions test circuit: RL = Load resistance. CL = Load capacitance including jig and probe capacitance. VEXT = External voltage for measuring switching times. Fig 16. Load circuit for switching times Table 11. Test data Supply voltage Input VCC VI tr, tf CL RL 1.4 V to 4.3 V VCC 2.5 ns 35 pF 50 NX3L4357 Product data sheet Load All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 12 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 12.2 Additional dynamic characteristics Table 12. Additional dynamic characteristics At recommended operating conditions; voltages are referenced to GND (ground = 0 V); VI = GND or VCC (unless otherwise specified); tr = tf 2.5 ns. Tamb = 25 C Symbol Parameter Conditions THD fi = 20 Hz to 20 kHz; RL = 32 ; see Figure 17 total harmonic distortion Min Typ Max VCC = 1.4 V; VI = 1 V (p-p) - 0.15 - % VCC = 1.65 V; VI = 1.2 V (p-p) - 0.10 - % [1] VCC = 2.3 V; VI = 1.5 V (p-p) - 0.02 - % VCC = 2.7 V; VI = 2 V (p-p) - 0.02 - % VCC = 4.3 V; VI = 2 V (p-p) - 0.02 - % - 0.01 - % - 30 - MHz - 20 - MHz - 90 - dB - 0.21 - V - 0.30 - V - 90 - dB VCC = 1.5 V - 10 - pC VCC = 1.8 V - 15 - pC VCC = 3.0 V; VI = 1 V (p-p); RL = 600 f(3dB) 3 dB frequency response RL = 50 ; see Figure 18 [1] port Y0, Y1 or Y2; VCC = 1.4 V to 4.3 V port Y0, Y1 and Y2; VCC = 1.4 V to 4.3 V iso isolation (OFF-state) fi = 100 kHz; RL = 50 ; see Figure 19 Vct crosstalk voltage between digital inputs and switch; fi = 1 MHz; CL = 50 pF; RL = 50 ; see Figure 20 [1] VCC = 1.4 V to 4.3 V VCC = 1.4 V to 3.6 V VCC = 3.6 V to 4.3 V Xtalk crosstalk between switches; fi = 100 kHz; RL = 50 ; see Figure 21 VCC = 1.4 V to 4.3 V charge injection Qinj [1] Unit [1] fi = 1 MHz; CL = 0.1 nF; RL = 1 M; Vgen = 0 V; Rgen = 0 ; see Figure 22 VCC = 2.5 V - 26 - pC VCC = 3.3 V - 36 - pC VCC = 4.3 V - 50 - pC fi is biased at 0.5VCC. NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 13 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 12.3 Test circuits VCC 0.5VCC Sn VIL or VIH RL Z Yn E VIL fi D GND 001aak772 Fig 17. Test circuit for measuring total harmonic distortion VCC 0.5VCC Sn VIL or VIH RL Z Yn E VIL fi dB GND 001aak773 Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads 3 dB. Fig 18. Test circuit for measuring the frequency response when channel is in ON-state 0.5VCC 0.5VCC VCC RL RL Sn VIL or VIH Z Yn E fi VIH dB GND 001aak774 Adjust fi voltage to obtain 0 dBm level at input. Fig 19. Test circuit for measuring isolation (OFF-state) NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 14 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 0.5VCC 0.5VCC VCC RL RL Sn VIL or VIH Z Yn E VI logic input G CL V VO GND 001aak775 a. Test circuit logic input (S0, S1, E) off on off VO Vct 001aak776 b. Input and output pulse definitions VI may be connected to Sn or E. Fig 20. Test circuit for measuring crosstalk voltage between digital inputs and switch VCC 0.5VCC 0.5VCC 0.5VCC RL VIL or VIH S0, S1 Z RL RL Y0 1 Y1 2 Y2 3 E VIH fi dB dB GND 001aak777 fi may be connected to Y0, Y1 or Y2. Fig 21. Test circuit for measuring crosstalk between switches NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 15 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input VCC Sn Z Yn E VIL G VI V VO RL Rgen Vgen CL GND 001aak778 a. Test circuit logic input (S0, S1, E) off on off ΔVO VO 001aak779 b. Input and output pulse definitions VI may be connected to Sn or E. Definition: Qinj = VO CL. VO = output voltage variation. Rgen = generator resistance. Vgen = generator voltage. Fig 22. Test circuit for measuring charge injection NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 16 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 13. Package outline XQFN10U: plastic extremely thin quad flat package; no leads; 10 terminals; UTLP based; body 2 x 1.55 x 0.5 mm A B D SOT1049-2 terminal 1 index area E A A1 detail X e2 L C L1 e v w 5 4 M M y y1 C C A B C 6 e1 b 3 7 e3 1/2 e1 2 8 1 9 terminal 1 index area metal area must not be soldered 10 X 0 2.5 mm scale DIMENSIONS (mm are the original dimensions) UNIT mm max nom min A A1 b D E e e1 e2 e3 L L1 v w y y1 0.50 0.05 0.03 0.00 0.30 0.23 0.15 1.65 1.55 1.45 2.1 2.0 1.9 0.58 0.5 1.16 1.5 0.4 0.3 0.2 0.15 0.08 0.00 0.1 0.05 0.1 0.05 REFERENCES OUTLINE VERSION IEC JEDEC JEITA SOT1049-2 --- MO-255 --- EUROPEAN PROJECTION ISSUE DATE 08-04-22 10-02-05 Fig 23. Package outline SOT1049-2 (XQFN10U) NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 17 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 14. Abbreviations Table 13. Abbreviations Acronym Description CDM Charged Device Model CMOS Complementary Metal-Oxide Semiconductor ESD ElectroStatic Discharge HBM Human Body Model MM Machine Model 15. Revision history Table 14. Revision history Document ID Release date Data sheet status Change notice Supersedes NX3L4357 v.4 20111107 Product data sheet - NX3L4357 v.3 Modifications: • Legal pages updated. NX3L4357 v.3 20101228 Product data sheet - NX3L4357 v.2 NX3L4357 v.2 20100428 Product data sheet - NX3L4357 v.1 NX3L4357 v.1 20091019 Product data sheet - - NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 18 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 16. Legal information 16.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 16.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification — The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 16.3 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer’s general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 19 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input Non-automotive qualified products — Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ standard warranty and NXP Semiconductors’ product specifications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors’ warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond 16.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. 17. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] NX3L4357 Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 4 — 7 November 2011 © NXP B.V. 2011. All rights reserved. 20 of 21 NX3L4357 NXP Semiconductors Low-ohmic single-pole triple-throw analog switch with enable input 18. Contents 1 2 3 4 5 6 7 7.1 7.2 8 9 10 11 11.1 11.2 11.3 12 12.1 12.2 12.3 13 14 15 16 16.1 16.2 16.3 16.4 17 18 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recommended operating conditions. . . . . . . . 5 Static characteristics. . . . . . . . . . . . . . . . . . . . . 5 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ON resistance . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ON resistance test circuit and graphs. . . . . . . . 8 Dynamic characteristics . . . . . . . . . . . . . . . . . 10 Waveforms and test circuits . . . . . . . . . . . . . . 11 Additional dynamic characteristics . . . . . . . . . 13 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 17 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 18 Legal information. . . . . . . . . . . . . . . . . . . . . . . 19 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 19 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Contact information. . . . . . . . . . . . . . . . . . . . . 20 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 7 November 2011 Document identifier: NX3L4357