FEDFOAT1509-01 OKI Electronic Components OAT1509-LV-CB/LB Issue Data : Jan. 15, 2002 Optical Service Channel Transceiver APPLICATION · DWDM Optical Service Channel Transmitter operated by T1 1.544Mbps FEATURES · · · · · · Integrated NRZ to/from CMI code/Decode functions TTL compatible interface Operation at 1.51µm/1.625um wavelength(C -band / L-Band) by Uncooled DFB- LD High output power > 0dBm and High sensitivity < - 44dBm for Long haul transmission Integrated CDR function +3.3V single power supply and Low power consumption 0.6W SPECIFICATION Parameter Type Bit rate Line code Operating wavelength Mean launched power range Minimum extinction ratio Received optical power [BER = 10 - 8] Power consumption Laser diode Fiber type Power supply voltage Operating temperature Dimension Unit Mbps nm dBm dB dBm W V °C mm OAT1509-LV-CB C-band OAT1509-LV-LB L-band 1.544 CMI 1510 ± 7 1625 ± 7 -3 to +3 ≥ 13 -44 to -8 0.6 (Typ.) 1.510 µm DFB-LD 1.625 µm DFB-LD Single mode fiber +3.3 ± 5% 0 to 60 42.9 ×44.5 × 13.5 1/5 FEDFOAT1509-01 OKI Semiconductor OAT1509-LV-CB/LB BLOCK DIAGRAM LD Module Transmitter Clock Detector Doubler CLK IN 1.544MHz OUT CMI Coder LD Monitor PD LD Driver DATA IN NRZ APC Circuit CRV IN TF Receiver PIN-Amp Module Tank CRV OUT IN PIN -PD CDR CMI Decorder DATA OUT NRZ CLK OUT 1.544MHz LOS 2/5 (10) 580 +19 0 (26.8) 5.92 (φ0.9) (φ0.9) Quality of the material:Iron(Nickel plating) (10.2) (0.8) (0.8) (25.4±0.3) (0.8) 44.5±0.5 OAT1509S-LV-CB-05 The terminal for attachment (4 places) Optical Connector 4.2 12.6 17.8 (12.5) L (10) (04) (03) An electric terminal Quality of the material: Brass(Gilding) Quality of the material: Iron(Nickel plating) Case back 13.5MAX 2x2.54=5.08 (Unit :mm) (3) OKI Semiconductor (01) 5.4±0.3 3.5 42.9±0.5 (5.2) (0.4) 0.635) ( 6x2.54=15.24 (3.12) (13.38) in the case of SC 554 +19 0 connector FEDFOAT1509-01 OAT1509-LV-CB/LB PACKAGE OUTLINE 3/5 41.9±0.5 (5.08±0.3) FEDFOAT1509-01 OKI Semiconductor OAT1509-LV-CB/LB PIN DESCRIPTIONS No. Symbol Functionality 01 GND Ground 02 Vcc Power supply (Vcc = +3.3 V) Los of incoming signal <LVTTL> 03 LOS A logic high on LOS indicates the absence of a signal 04 CLK OUT Negative clo ck output <LVTTL> 05 DATA OUT Positive NZR data output <LVTTL> 06 CRV OUT Code Rule Violation output <LVTTL> 07 TF 08 CLK IN Transmit fail alarm output <LVTTL> Positive clock input <LVTTL> 09 DATA IN Positive NRZ data input <LVTTL> 10 CVR IN Code Rule Violation signal input <LVTTL> 4/5 FEDFOAT1509-01 OKI Semiconductor OAT1509-LV-CB/LB NOTICE 1. The information contained herein can change without notice owing to product and/or technical improvements. Before using the product, please make sure that the information being referred to is up -to- date. 2. The outline of action and examples for application circuits described herein have been chosen as an explanation for the standard action and performance of the product. When planning to use the product, please ensure that the external conditions are reflected in the actual circuit, assembly, and program designs. 3. When designing your product, please use our product below the specified maximum ratings and within the specified operating ranges including, but not limited to, operating voltage, power dissipation, and operating temperature. 4. Oki assumes no responsibility or liability whatsoever for any failure or unusual or unexpected operation resulting from misuse, neglect, improper installation, repair, alteration or accident, improper handling, or unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified maximum ratings or operation outside the specified operating range. 5. Neither indemnity against nor license of a third party’s industrial and intellectual property right, etc. is granted by us in connection with the use of the product and/or the information and drawings contained herein. No responsibility is assumed by us for any infringement of a third party’s right which may result from the use thereof. 6. The products listed in this document are intended for use in general electronics equipment for commercial applications (e.g., office automation, communication equipment, measurement equipment, consumer electronics, etc.). These products are not authorized for use in any system or application that requires special or enhanced quality and reliability characteristics nor in any system or application where the failure of such system or application may result in the loss or damage of property, or death or injury to humans. Such applications include, but are not limited to, traffic and automotive equipment, safety devices, aerospace equipment, nuclear power control, medical equipment, and life- support systems. 7. Certain products in this document may need government approval before they can be exported to particular countries. The purchaser assumes the responsibility of determining the legality of export of these products and will take appropriate and necessary steps at their own expense for these. 8. No part of the contents contained herein may be reprinted or reproduced without our prior permission. 9. Qualification and Reliability To help ensure high product reliability and customer satisfaction, OKI is committed to an intensive quality program that starts in the design phase and proceeds through the manufacturing process. Optical transceiver modules are qualified to OKI internal standards using MIL-STD-883 test methods and procedures and using sample techniques consistent with Telcordia requirements. This qualification program fully meets the intent of Telcordia reliability practices GR- 468- CORE. 10. Laser Safety All version of transceiver are Class 1 Laser products FDA complies with 21 CFR 1040.10 and 1040.11 requirements. Also, all versions are Class 1 Laser products pre IEC 825-1. Copyright 2002 Oki Electric Industry Co., Ltd. 5/5