OM3901SC OM3903SC OM3905SC OM3907SC OM3909SC OM3902SC OM3904SC OM3906SC OM3908SC DUAL POSITIVE AND NEGATIVE FIXED VOLTAGE REGULATORS APPROVED TO DESC DRAWING Dual 5V, 12V and 15V, 1.5 Amp Fixed Voltage Regulators In Single Hermetic MO-078AA Package FEATURES • • • • • • • Positive And Negative Regulators In One Package Isolated Hermetic Package, JEDEC MO-078AA Output Voltages 5V, 12V and 15V Output Voltages Set Internally To ±1.0% Built-In Thermal Overload Protection Short Circuit Current Limiting Similar to Industry Standards 7800 & 7900 Series DESCRIPTION This series of products offers a positive and a negative fixed voltage regulator in one hermetically sealed, 5 pin package whose outline is similar to the industry standard TO-247 package. With heat sinking, they can regulate over 1.5 Amp of output current per device. Standard voltages are + or - 5V, 12V and 15V. Output voltages are internally trimmed to ±1.0% of nominal voltage. These devices are ideally suited for Military applications where small size and high reliability are required. To order, use the following Omnirel part numbers to determine the required output voltage of each regulator within one package. PART NUMBER DESIGNATOR Standard Military Drawing Number 5962-8949002 XX 5962-8949003 XX 5962-8949004 XX 5962-8949005 XX 5962-8949006 XX 5962-8949007 XX 5962-8949008 XX 5962-8949009 XX 5962-8949001 XX 4 11 R0 Omnirel Part Number OM3901SC OM3902SC OM3903SC OM3904SC OM3905SC OM3906SC OM3907SC OM3908SC OM3909SC 3.3 - 107 Output Voltages Positive Negative +5V -5V +5V -12V +5V -15V +12V -5V +12V -12V +12V -15V +15V -5V +15V -12V +15V -15V 3.3 OM3901SC - OM3909SC INDIVIDUAL POSITIVE REGULATORS ELECTRICAL CHARACTERISTICS +5 Volt VIN = 10V, Io = 500mA, -55°C TA 125°C (unless otherwise specified) Parameter Symbol Test Conditions Min. Max. Unit Output Voltage VOUT TA = 25°C 4.92 5.08 V 4.85 5.15 V 5 mV VIN = 7.5V to 20V Line Regulation VRLINE • VIN = 7.5V to 20V • (Note 1) VIN = 8.0V to 12V • Load Regulation VRLOAD IO = 5mA to 1.5 Amp • (Note 1) IO = 250mA to 750 mA • Standby Current Drain ISCD Standby Current Drain DISCD Change With Line (Line) Standby Current Drain DISCD Change With Load (Load) mV 10 mV 12 mV 25 mV 6 mV 15 mV 6 mA • • 6.5 mA 0.8 mA IO = 5mA to 1000mA • 0.5 mA Dropout Voltage VDO TA = 25°C, DVOUT = 100mV, IO = 1.0A IO (pk) TA = 25°C Short Circuit Current IDS VIN = 35V 1.5 • (Note 2) DVIN mV 4 VIN = 7.5V to 20V Peak Output Current Ripple Rejection 12 2.5 V 3.3 A 1.2 A 2.8 f =120 Hz, DVIN = 10V 66 • DVOUT (Note 3) NO TA = 25°C, f =10 Hz to 100KHz 40 Long Term Stability DVOUT TA = 25°C, t = 1000 hrs. 75 (Note 3) Dt Output Noise Voltage 60 dB (Note 3) µV/V RMS ELECTRICAL CHARACTERISTICS +12 Volt mV VIN = 19V, Io = 500mA, -55°C TA 125°C (unless otherwise specified) Parameter Symbol Test Conditions Min. Max. Unit Output Voltage VOUT TA = 25°C 11.88 12.12 V 11.64 12.36 V 18 mV VIN = 14.5V to 27V Line Regulation VRLINE • VIN = 14.5V to 27V • (Note 1) VIN = 16V to 22V • Load Regulation VRLOAD IO = 5mA to 1.5 Amp • (Note 1) IO = 250mA to 750 mA • 3.3 A dB Standby Current Drain ISCD Standby Current Drain DISCD Change With Line (Line) Standby Current Drain DISCD Change With Load (Load) mV 30 mV 32 mV 60 mV 20 mV 40 mV 6.0 mA • • 6.5 mA 0.8 mA IO = 5mA to 1000mA • 0.5 mA • Dropout Voltage VDO DVOUT = 100mV, IO = 1.0A IO (pk) TA = 25°C Short Circuit Current IDS VIN = 35V 1.5 • (Note 2) DVIN mV 9 VIN = 15V to 30V Peak Output Current Ripple Rejection 50 f =120 Hz, DVIN = 10V 2.5 V 3.3 A 1.2 A 2.8 61 • DVOUT (Note 3) NO TA = 25°C, f =10 Hz to 100KHz 40 Long Term Stability DVOUT TA = 25°C, t = 1000 hrs. 120 (Note 3) Dt Output Noise Voltage A dB 54 dB (Note 3) µV/V RMS mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = 35V. 3. If not tested, shall be guaranteed to the specified limits. The • denotes the specifications which apply over the full operating temperature range. 3.3 - 108 OM3901SC - OM3909SC ELECTRICAL CHARACTERISTICS +15 Volt VIN = 23V, Io = 500mA, -55°C TA 125°C (unless otherwise specified) Parameter Symbol Test Conditions Min. Max. Unit Output Voltage VOUT TA = 25°C 14.8 15.2 V 14.6 15.4 V 20 mV 50 mV VIN = 18.5V to 30V Line Regulation VRLINE • VIN = 17.5V to 30V • (Note 1) VIN = 20V to 26V Load Regulation VRLOAD (Note 1) 15 mV • 25 mV 35 mV • 75 mV 21 mV • 45 mV IO = 5mA to 1.5 Amp IO = 5mA to 1.0 Amp IO = 250mA to 750 mA Standby Current Drain ISCD Standby Current Drain DISCD Change With Line (Line) Standby Current Drain DISCD Change With Load (Load) 6.0 mA 6.5 mA VIN = 18.5V to 30V • • 0.8 mA IO = 5mA to 1000mA • 0.5 mA Dropout Voltage VDO TA = 25°C, DVOUT = 100mV, IO = 1.0A Peak Output Current IO (pk) TA = 25°C Short Circuit Current IDS VIN = 35V • (Note 2) Ripple Rejection 1.5 DVIN 2.5 V 3.3 A 1.2 A 2.8 f =120 Hz, DVIN = 10V 54 • DVOUT (Note 3) NO TA = 25°C, f =10 Hz to 100KHz 40 Long Term Stability DVOUT TA = 25°C, t = 1000 hrs. 150 (Note 3) Dt Output Noise Voltage A dB 52 dB (Note 3) µV/V RMS ELECTRICAL CHARACTERISTICS -5 Volt mV VIN = -10V, Io = 500mA, -55°C TA 125°C (unless otherwise specified) Parameter Symbol Test Conditions Min. Max. Unit Output Voltage VOUT TA = 25°C -4.95 -5.05 V -4.85 -5.15 V 12 mV 25 mV VIN = -7.5V to -20V Line Regulation VRLINE • VIN = -7.5V to -20V • (Note 1) VIN = -8.0V to -12V Load Regulation VRLOAD 5 mV • 12 mV 20 mV • 25 mV 15 mV • 30 mV IO = 5mA to 1.5 Amp (Note 1) IO = 250mA to 750 mA Standby Current Drain ISCD Standby Current Drain DISCD Change With Line (Line) Standby Current Drain DISCD Change With Load (Load) 2.5 mA 3.0 mA VIN = -7.0V to -20V • • 0.4 mA IO = 5mA to 1000mA • 0.4 mA • Dropout Voltage VDO DVOUT = 100mV, IO = 1.0A Peak Output Current IO (pk) TA = 25°C Short Circuit Current IDS VIN = -35V DVIN f =120 Hz, DVIN = -10V • (Note 2) Ripple Rejection 1.5 2.5 V 3.3 A 1.2 A 2.8 63 • DVOUT (Note 3) NO TA = 25°C, f =10 Hz to 100KHz 40 Long Term Stability DVOUT TA = 25°C, t = 1000 hrs. 75 (Note 3) Dt Output Noise Voltage A dB 60 dB (Note 3) µV/V RMS mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN =+35V, positive regulator; .VIN = -35V, negative regulator. 3. If not tested, shall be guaranteed to the specified limits. The • denotes the specifications which apply over the full operating temperature range. 3.3 - 109 3.3 OM3901SC - OM3909SC ELECTRICAL CHARACTERISTICS -12 Volt VIN = -19V, Io = 500mA, -55°C TA 125°C (unless otherwise specified) Parameter Symbol Test Conditions Min. Max. Unit Output Voltage VOUT TA = 25°C -11.88 -12.12 V -11.64 -12.36 V 20 mV 50 mV VIN = -14.5V to -27V Line Regulation VRLINE • VIN = -14.5V to -27V • (Note 1) VIN = -16V to -22V Load Regulation VRLOAD 10 mV • 30 mV 32 mV • 60 mV 16 mV • 30 mV IO = 5mA to 1.5 Amp (Note 1) IO = 250mA to 750 mA Standby Current Drain ISCD Standby Current Drain DISCD Change With Line (Line) Standby Current Drain DISCD Change With Load (Load) 3.5 mA 4.0 mA VIN = -14.5V to -27V • • 0.8 mA IO = 5mA to 1000mA • 0.5 mA • 1.8 V Dropout Voltage VDO DVOUT = 100mV, IO = 1.0A Peak Output Current IO (pk) TA = 25°C, IO = 5mA to 1A Short Circuit Current IDS VIN = -35V DVIN f =120 Hz, DVIN = -10V • (Note 2) Ripple Rejection 1.5 3.3 A 1.2 A 2.8 56 • DVOUT (Note 3) NO TA = 25°C, f =10 Hz to 100KHz 40 Long Term Stability DVOUT TA = 25°C, t = 1000 hrs. 120 (Note 3) Dt Output Noise Voltage 53 dB (Note 3) µV/V RMS ELECTRICAL CHARACTERISTICS -15 Volt mV VIN = -23V, Io = 500mA, -55°C TA 125°C (unless otherwise specified) Parameter Symbol Test Conditions Min. Max. Unit Output Voltage VOUT TA = 25°C -14.85 -15.15 V -14.55 -15.45 V 25 mV 50 mV VIN = -17.5V to -30V Line Regulation VRLINE • VIN = -17.5V to -30V • (Note 1) VIN = -20V to -26V Load Regulation VRLOAD 15 mV • 25 mV 35 mV • 75 mV 21 mV • 45 mV IO = 5mA to 1.5 Amp (Note 1) IO = 250mA to 750 mA Standby Current Drain 3.3 A dB ISCD Standby Current Drain DISCD Change With Line (Line) Standby Current Drain DISCD Change With Load (Load) 6.0 mA 6.5 mA VIN = -17.5V to -30V • • 0.8 mA IO = 5mA to 1000mA • 0.5 mA • Dropout Voltage VDO DVOUT = 100mV, IO = 1.0A Peak Output Current IO (pk) TA = 25°C Short Circuit Current IDS VIN = -35V • (Note 2) Ripple Rejection 1.5 DVIN f =120 Hz, DVIN = -10V 2.5 V 3.3 A 1.2 A 2.8 53 • DVOUT (Note 3) NO TA = 25°C, f =10 Hz to 100KHz 40 Long Term Stability DVOUT TA = 25°C, t = 1000 hrs. 150 (Note 3) Dt Output Noise Voltage A dB 50 dB (Note 3) µV/V RMS mV Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = -35V. 3. If not tested, shall be guaranteed to the specified limits. The • denotes the specifications which apply over the full operating temperature range. 3.3 - 110