SIDACtor ® Protection Thyristors High Surge Current Protection High Surge Current Series - DO-214 Description The High Surge Current DO-214 Series are SIDACtor® devices designed to protect equipment located in hostile environments from overvoltage transients. The series provides a 200A 10/1000 μs rated surface mount solution that enables equipment to comply with enhanced surge requirments now specified in regulatory and customer requirements. Features and Benefits t Low voltage overshoot Agency Approvals Agency Agency File Number t Low on-state voltage t 200A 10x1000 Surge Rating t Does not degrade with use t 1000A 2x10 Surge Rating t Fails short circuit when surged in excess of ratings E133083 Pinout Designation Applicable Global Standards Not Applicable Schematic Symbol t TIA-968-A t GR 1089 Intra-building t TIA-968-B t IEC 61000-4-5 t ITU K.20/21 Enhanced Level t YD/T 1082 t ITU K.20/21 Basic Level t YD/T 950 t YD/T 993 t GR 1089 Inter-building Electrical Characteristics Part Number P0080SDLRP P0640SDLRP P0720SDLRP P0900SDLRP P1100SDLRP P1300SDLRP P1500SDLRP P1800SDLRP P2300SDLRP P2600SDLRP P3100SDLRP P3500SDLRP Marking P-8D P06D P07D P09D P11D P13D P15D P18D P23D P26D P31D P35D VDRM @lDRM=5μA VS @100V/μs V min V max 6 58 65 75 90 120 140 170 190 220 275 320 25 77 88 98 130 160 180 220 260 300 350 400 IH IT** mA min mA max A max 50 50 50 50 50 50 50 50 50 50 50 50 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are uni-directional ** Will meet 4.4A power cross requirement without fire hazard. © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. IS 184 Revised: February 22, 2011 800 800 800 800 800 800 800 800 800 800 800 800 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 VT @IT=2.2A Capacitance @1MHz, 2V bias V max pf min pF max 4 4 4 4 4 4 4 4 4 4 4 4 50 100 100 95 75 65 60 50 50 50 45 45 150 160 150 140 115 100 90 90 80 75 70 65 SIDACtor ® Protection Thyristors High Surge Current Protection Series Surge Ratings D IPP ITSM 50/60 Hz di/dt A min A min A/μs max — 50 1000 0.2x310 1 0.5x700 2 2x10 1 2x10 2 8x20 1 1.2x50 2 10x160 1 10x160 2 10x560 1 10x560 2 5x320 1 9x720 2 10x360 1 10x360 2 10x1000 1 10x1000 2 5x310 1 10x700 2 A min A min A min A min A min A min A min A min — 1000 800 — — — — 200 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ 1 Current waveform in μs 2 Voltage waveform in μs Thermal Considerations Package DO-214AA Symbol Parameter Value Unit TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C R0JA Thermal Resistance: Junction to Ambient 90 °C/W V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 td tr t – Time (μs) -I Normalized DC Holding Current vs. Case Temperature Normalized VS Change vs. Junction Temperature IH 8 6 25 °C 4 IH (TC = 25ºC) 10 Ratio of Percent of VS Change – % 2.0 14 12 2 0 -4 -6 1.8 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C 185 Revised: February 22, 2011 SIDACtor ® Protection Thyristors High Surge Current Protection Soldering Parameters Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. - Temperature Min (Ts(min)) Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ Figure 1 TP tP Critical Zone TL to TP Ramp-up Temperature Reflow Condition TL TS(max) tL Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Time Physical Specifications Environmental Specifications Lead Material Copper Alloy High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Terminal Finish 100% Matte-Tin Plated Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Autoclave (Pressure Cooker Test) ¡$3)BUNVQUPIST&*" JEDEC, JESD22-A-102 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM Body Material UL recognized epoxy meeting flammability classification 94V-0 Part Numbering Part Marking P xxx 0 S DL RP TYPE P: SIDACtor MEDIAN VOLTAGE CONSTRUCTION VARIABLE Pxxx xxxxx REEL PACK RoHS COMPLIANT IPP RATING PACKAGE TYPE © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 186 Revised: February 22, 2011 Part Marking Code (Refer to Electrical Characteristics Table) Date Code SIDACtor ® Protection Thyristors High Surge Current Protection Dimensions — DO-214AA Pad Outline Case Temperature Measurement Point B D 0.079 (2.0) 0.110 (2.8) C A 0.079 (2.0) H E inch (millimeter) F K Inches Dimensions G Min Max Min Max A 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 C 0.077 0.087 1.95 2.20 4.60 D 0.159 0.181 4.05 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 K 0.006 0.016 0.15 0.41 Packing Options Package Type S Description Quantity Added Suffix Industry Standard DO-214AA Tape and Reel Pack 2500 RP EIA-481-D Tape and Reel Specification — DO-214AA 0.157 (4.0) 0.472 (12.0) 0.36 (9.2) 0.315 (8.0) 0.059 DIA (1.5) 12.99 (330.0) Direction of Feed 0.49 (12.4) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. Cover tape Dimensions are in inches (and millimeters). 0.512 (13.0) Arbor Hole Dia. 187 Revised: February 22, 2011 Millimeters