SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Q2L Series - 3.3x3.3 QFN Description Q2L Series 3.3x3.3 QFN are low capacitance SIDACtor® devices designed to protect high density broadband equipment from damaging overvoltage transients. The series provides a low profile, chip scale surface mount solution that enables broadband equipment to comply with global regulatory standards while limiting the impact to broadband signals and board space. Features and Benefits Agency tDoes not degrade with use tFails short circuit when surged in excess of ratings t-PXQSPGJMF t4NBMMGPPUQSJOU tLow capacitance tLow voltage overshoot tLow on-state voltage Agency Approvals Agency File Number E133083 Applicable Global Standards Pinout Designation Not Applicable Schematic Symbol t5*"" t(3*OUSBCVJMEJOH t5*"# t*&$ t*56,&OIBODFE Level t:%5 t*56,#BTJD-FWFM t:%5 t:%5 t(3*OUFSCVJMEJOH Electrical Characteristics Part Number P0080Q22CLRP P0300Q22CLRP P0640Q22CLRP P0720Q22CLRP P0900Q22CLRP P1100Q22CLRP P1300Q22CLRP P1500Q22CLRP P1800Q22CLRP P2300Q22CLRP P2600Q22CLRP P3100Q22CLRP P3500Q22CLRP Marking P-8C P03C P06C P07C P09C P11C P13C P15C P18C P23C P26C P31C P35C VDRM VS @lDRM=5μA @100V/μs V min V max 6 25 58 65 75 90 120 140 170 190 220 275 320 25 40 77 88 98 130 160 180 220 260 300 350 400 IH mA min mA max 50 50 150 150 150 150 150 150 150 150 150 150 150 Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional (unless otherwise noted). © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. IS 63 Revised: February 22, 2011 800 800 800 800 800 800 800 800 800 800 800 800 800 Capacitance @1MHz, 2V bias IT VT@IT = 2.2 Amps A max V max pF min pF max 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 5 5 5 5 5 5 5 5 5 5 5 5 5 35 25 55 50 45 45 40 35 35 30 30 30 25 75 45 85 75 70 70 60 55 50 50 45 45 40 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Surge Ratings ITSM Ipp Series C di/dt 2x10μs 1.2x50μs/8x20μs 10x160μs 10x560μs 10x1000μs 50 / 60 Hz A min A min A min A min A min A min Amps/μs max 500 400 200 150 100 30 500 Notes: - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPPSBUJOHTBQQMJDBCMFPWFSUFNQFSBUVSFSBOHFPG$UP$ - The device must initially be in thermal equilibrium with -40°C < TJ <¡$ Thermal Considerations Package Symbol Parameter Value Unit 3.3 x 3.3 QFN TJ Operating Junction Temperature Range UP °C TS Storage Temperature Range UP °C R0JA Thermal Resistance: Junction to Ambient 120 °C/W V-I Characteristics tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP +I IT IS IH IDRM -V +V VT VDRM VS tr = rise time to peak value td = decay time to half value Peak Value 100 Waveform = tr x td 50 Half Value 0 td tr 0 t – Time (μs) -I Normalized DC Holding Current vs. Case Temperature 2.0 12 1.8 10 IH 8 6 25 °C 4 IH (TC = 25ºC) 14 Ratio of Percent of VS Change – % Normalized VS Change vs. Junction Temperature 2 0 -4 -6 1.6 1.4 25°C 1.2 1.0 0.8 0.6 0.4 -8 -40 -20 0 -40 20 40 60 80 100 120 140 160 0 20 40 60 80 100 120 140 Case Temperature (TC) - ºC Junction Temperature (TJ) – °C © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. -20 64 Revised: February 22, 2011 160 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Soldering Parameters Pb-Free assembly (see Fig. 1) ¡$ ¡$ 60-180 secs. - Temperature Min (Ts(min)) - Temperature Max (Ts(max)) Pre Heat - Time (Min to Max) (ts) Average ramp up rate (Liquidus Temp (TL) to peak) 3°C/sec. Max. TS(max) to TL - Ramp-up Rate 3°C/sec. Max. Reflow - Temperature (TL) (Liquidus) ¡$ - Temperature (tL) 60-150 secs. Peak Temp (TP) ¡$ Time within 5°C of actual Peak Temp (tp) 30 secs. Max. Ramp-down Rate 6°C/sec. Max. Time 25°C to Peak Temp (TP) 8 min. Max. Do not exceed ¡$ Figure 1 tP TP Critical Zone TL to TP Ramp-up TL Temperature Reflow Condition tL TS(max) Ramp-down Preheat TS(min) tS 25 time to peak temperature (t 25ºC to peak) Environmental Specifications Physical Specifications Lead Material Time High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ¡$PS¡$ 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 Temp Cycling ¡$UP¡$NJOEXFMMVQUP cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 Biased Temp & Humidity 52 VDC¡$ 3)VQUPIST&*" JEDEC, JESD22-A-101 High Temp Storage ¡$IST.*-45%.FUIPE JEDEC, JESD22-A-101 Low Temp Storage -65°C, 1008 hrs. Thermal Shock ¡$UP¡$NJOEXFMMTFDUSBOTGFS 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 Resistance to Solder Heat ¡$TFDT.*-45%.FUIPE Moisture Sensitivity Level 3)¡$ISTSFnPXDZDMFT ¡$1FBL +&%&$+45%-FWFM Copper Alloy Terminal Finish 100% Matte-Tin Plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Dimensions — 3.3x3.3 QFN BOTTOM VIEW TOP VIEW Dimensions C A E J B END VIEW A B C E F H J K1 K2 M1 M2 N1 N2 F H 1.50 (.059”) SIDE VIEW 2.54 (.100”) 1.27 (.050”) N2 N1 K1 M1 M2 © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. K2 Recommended Soldering Pad Outline (Reference Only) 65 Revised: February 22, 2011 Inches Millimeters Min Max Min Max 0.126 0.126 0.075 0.011 0.088 0.035 0.000 0.004 0.004 0.063 0.045 0.095 0.082 0.134 0.134 0.083 0.019 0.096 0.043 0.008 0.012 0.012 0.071 0.053 0.103 0.090 3.200 3.200 1.900 0.285 2.230 0.900 0.000 0.100 0.100 1.610 1.153 2.420 2.080 3.400 3.400 2.100 0.485 2.430 1.100 0.200 0.300 0.300 1.810 1.353 2.620 2.280 SIDACtor ® Protection Thyristors Broadband Optimized™ Protection Part Numbering Part Marking P xxx 0 Q22 C L RP Terminals on Back TYPE P=SIDACtor REEL PACK MEDIAN VOLTAGE RoHS COMPLIANT CONSTRUCTION VARIABLE IPP RATING XXXX XXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date code PACKAGE TYPE Packing Options Package Type Description Quantity Added Suffix Industry Standard Q22 3.3x3.3 QFN Tape and Reel Pack 5000 RP EIA-481-D Tape and Reel Specifications — 3.3x3.3 QFN Reel Dimension Symbols A B C D N W1 A0 B0 D0 D1 E1 E2 C A D N W1 B Tape Leader and Trailer Dimensions END CARRIER TAPE START COVER TAPE F TRAILER 160mm MIN LEADER 400mm MIN K0 P0 P1 Tape Dimension Items D0 P0 P2 T CARRIER TAPE D1 T W B0 F E2 W W0 K0 P2 E1 P1 W0 A0 COVER TAPE © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 66 Revised: February 22, 2011 Description Inches Millimeters Min Max Min Reel Diameter N/A 12.992 N/A Drive Spoke Width 0.059 N/A 1.50 Arbor Hole Diameter 0.504 0.531 12.80 Drive Spoke Diameter 0.795 N/A 20.20 Hub Diameter 1.969 N/A 50.00 Reel Inner Width at Hub 0.488 0.567 12.40 Pocket Width at Bottom 0.138 0.146 3.50 Pocket Length at Bottom 0.138 0.146 3.50 Feed Hole Diameter 0.059 0.063 1.50 Pocket Hole Diameter 0.059 N/A 1.50 Feed Hole Position 1 0.065 0.073 1.65 Feed Hole Position 2 0.400 0.408 10.15 Feed Hole Center 0.215 0.219 5.45 Pocket Hole Center 2 Pocket Depth 0.039 0.051 1.00 Feed Hole Pitch 0.153 0.161 3.90 Component Spacing 0.311 0.319 7.90 Feed Hole Center 0.077 0.081 1.90 Pocket Hole Center 1 Carrier Tape Thickness 0.010 0.014 0.25 Embossed Carrier 0.453 0.484 11.50 Tape Width Cover Tape Width 0.358 0.366 9.10 Max 330.0 N/A 13.50 N/A N/A 14.40 3.70 3.70 1.60 N/A 1.85 10.35 5.55 1.30 4.10 8.10 2.05 0.35 12.30 9.30