95252 ANALOG PRODUCTS DIVISION PA2223 LoPro Dual SPDT Analog Switch ™ Features CMOS Technology for Bus and Analog Applications Description Low On-Resistance: 0.6Ω. Vcc Range: 1.8V to 4.2V Rail-to-Rail Signal Range High Off Isolation: -75dB @ 100kHz Crosstalk Rejection: -90dB @ 100kHz Bandwidth fCO = 100MHz ProTek Analog’s PA2223 is a dual high-bandwidth, fast single-pole double throw (SPDT) CMOS switch. It can be used as an analog switch or as a low-delay bus switch. Specified over a operating power supply voltage, 1.8V to 4.2V, the PA2223 has an On-Resistance of 0.6Ω at +2.7V. Break-before-make switching prevents both switches being enabled simultaneously. This eliminates signal disruption during switching. Break-Before-Make Switching Extended Industrial Temperature Range: –40°C to 85°C LoPro© Packaging (Pb-free): 10-Lead Micro Package Functional Block Diagram Applications NC1 NO1 COM1 NC2 IN1 NO2 COM2 IN2 Fig. 1 PA2223 Pin No. Name Description 1 VCC Positive Power Supply 2,10 NOX DATA Port (Normally Open) 3,9 COMX Common Port / DATA Port 4,8 INX Logic Control 5,7 NCX DATA Port (Normally Closed) 6 GND Ground IN2 8 COM 9 NO2 10 7 6 1 2 NO1 Pin Descriptions GND Pin Configuration (Top View) NC2 Cell Phones PDAs MP3 players Portable Instrumentation Computer Peripherals Speaker Headset Switching Power Routing Relay Replacement Audio and Video Signal Routing PCMCIA Cards Modems VCC 5 NC1 4 IN1 3 COM1 Ordering Information Logic Function Table Logic Input (INX) Function 0 NCX Connected to COMX 1 NOX Connected to COMX Temperature Range -40 to 85 °C Package Part Number 10 Lead LoPro PA2223-T7 561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480)632-1715 www.protekanalog.com 95252 REV0. 05/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS PA2223 LoPro Dual SPDT Analog Switch ™ ANALOG PRODUCTS DIVISION Absolute Maximum Ratings(1) Power Dissipation (PD) @ +85°C ........................ …250mW Recommended Operating Conditions(3) Supply Voltage VCC ....................................................4.5V (2) DC Switch Voltage (VS) ....................................VCC +0.5V DC Input Voltage (VIN)(2) .............................................4.5V Analog Signal Range.....................Min -1.0 to Max VCC +1.0 Continuous Current NO_NC_COM_ ...............±300mA Peak Current NO_NC_COM_ (pulsed at 1ms 50% duty cycle) ....................±400mA Peak Current NO_NC_COM_ (pulsed at 1ms 10% duty cycle) ........................... ±500mA Storage Temperature Range (TSTG) .. …..–65°C to +150°C Junction Temperature under Bias (TJ)..........................150°C Junction Lead Temperature (TL) (Soldering, 10 seconds).............................................260°C Notes: Supply Voltage Operating (VCC) ………………………1.8V to 4.2V Control Input Voltage (VIN)……………….. 0V to VCC Switch Input Voltage (VIN)…………………………. -0.3V to VCC Output Voltage (VOUT)……………………………………………………… 0V to VCC Operating Temperature (TA)………………………... –40°C to +85°C Input Rise and Fall Time (tr,tf) Control Input VCC = 2.3V - 3.6V………………..0ns/V to 10ns/V Thermal Resistance (θJA)………………………………….350°C/W Lead Temperature (soldering 10s)……………………… .+240°C 1. "Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. 2. The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. 3. Control input must be held HIGH or LOW; it must not float. 4. Internal Resistance RTERM is guaranteed by design and not production tested. Capacitance Parameter Symbol Test Conditions NC Off Capacitance CNC(OFF) f =1MHz, See Test Circuit Figure7. 35 NO Off Capacitance CNO(OFF) f =1MHz, See Test Circuit Figure7. 35 NC On Capacitance CNC(ON) f =1MHz, See Test Circuit Figure8. 95 NO On Capacitance CNO(ON) f =1MHz, See Test Circuit Figure8. 95 CIN f =1MHz, See Test Circuit Figure7. 1.5 Control Pin Input Capacitance Min Typ Max 561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480)632-1715 www.protekanalog.com 95252 REV0. 05/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS Unit pF ANALOG PRODUCTS DIVISION PA2223 LoPro Dual SPDT Analog Switch ™ DC Electrical Characteristics +3V Supply (VCC = 2.7V to 3.3V, TA = –40°C to 85°C, unless otherwise noted. Typical values are at 3V and +25°C.) Parameter Symbol Test Conditions Min Typ Max Unit VCC V Analog Switch Analog Signal Range VNO,VNC, VCOM NC On-Resistance RON(NC) NO On-Resistance RON(No) On-Resistance Match Between Channels NC On-Resistance Flatness NO On-Resistance Flatness NO or NC Off Leakage Current COM On Leakage Current ∆RON RONF(NC) RONF(NO) IOFF(NO) or IOFF(NC) ICOM(ON) -0.3 VCC = 2.7V, ICOM = 100mA, VNC = 0 to VCC VCC = 2.7V, ICOM = 100mA, VNO = 0 to VCC VCC = 2.7V, ICOM = 100mA, VNO or VNC = 1.5V VCC = 2.7V, ICOM = 100mA, VNC = 0 to VCC VCC = 2.7V, ICOM = 100mA, VNO = 0 to VCC VCC = 3.3V, ICOM, VNO or VNC = 3.0V, 0.3V VCOM = 0.3V,3.0V VCC = 3.3V, ICOM, VNO or VNC = 3.0V, 0.3V VCOM = 0.3V,3.0V or Floating 0.4 0.6 0.4 0.6 0.01 0.05 Ω 0.2 0.2 -20 20 -20 20 nA Digital I/O Input Logic High VIH 1.3 Input Logic Low VIL Input Hysteresis VH VCC = 3.3V IN Input Leakage Current IIN VIN = 0 or VCC Supply Current ICC VCC = 3.6V, VIN = 0 or VCC V 0.5 Switch and AC Characteristics Parameter Symbol Test Conditions Turn-On Time tON VCC = 2.7V,VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF. 300 -0.5 Min mV 0.5 µA 0.9 1.2 nA Typ Max Unit 15 25 4 10 See Test Circuit Figure 1 & 2 Turn-Off Time tOFF VCC = 2.7V,VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF. nS See Test Circuit Figure 1 & 2 Break-BeforeMake Delay tBBM 20 See Test Circuit Figure 3 Charge Injection Off-Isolation VCC = 2.7V,VNO or VNC = 1.5V, RL = 50Ω, CL = 35pF. Q QIRR COM = 0, RS = 0, CL = 1nF. VGEN = 0 See Test Circuit Figure 4 CL = 5pF, RL = 50Ω, f = 100kHz, VCOM = 1VRMS 55 -75 See Test Circuit Figure 5 Crosstalk XTALK CL = 5pF, RL = 50Ω, f = 100kHz, VCOM = 1VRMS pC dB -90 See Test Circuit Figure 6 3dB Bandwidth f3dB See Test Circuit Figure 9 100 561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480)632-1715 www.protekanalog.com 95252 REV0. 05/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS MHz PA2223 LoPro Dual SPDT Analog Switch ™ ANALOG PRODUCTS DIVISION Typical Characteristics NO RDSON NC RDSON 2.0 2.0 1.8 2.7Volt 1.6 1.6 1.4 1.4 RDSON (OHMS) RDSON (OHMS) 1.8 1.2 1.0 3.3Volt 0.8 2.7Volt 1.2 1.0 3.3Volt 0.8 0.6 0.6 0.4 0.4 0.2 0.2 0.0 0.0 0.0 1.0 2.0 0.0 3.0 1.0 NO RON vs V COM (Temp) 3.0 NC RON vs V COM (Tem p) 3.0 3.0 2.5 2.5 +85°C +85°C 2.0 RON (OHMS) 2.0 RON (OHMS) 2.0 V COM (Volts) V COM (Volts) +25°C 1.5 1.0 +25°C 1.5 1.0 -40°C -40°C 0.5 0.5 0.0 0.0 0.0 1.0 2.0 3.0 0.0 1.0 2.0 3.0 V COM (Volts) V COM (Volts) VDD vs IDD 1000 900 Supply Current (pA) 800 700 600 500 400 300 200 100 0 0.0 1.0 2.0 3.0 Supply Voltage V DD (Volts) Note: Characteristics are guaranteed by design and are not production tested. 561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480)632-1715 www.protekanalog.com 95252 REV0. 05/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS PA2223 LoPro Dual SPDT Analog Switch ™ ANALOG PRODUCTS DIVISION Test Circuits and Timing Diagrams VCC COM NC or NO VIN VOUT IN CL RL 50Ω 35pF GND Logic Input CL includes fixture and stray capacitance Figure 1. AC Test Circuit Note1. Unused Input (NO or NC) must be grounded VIH Logic Input V IL tr < 5nS Off On 50% Off tf < 5nS tOFF Switch Output 90% 90% 0V tON Logic Input Waveforms inverted for Switches that have opposite logic Figure2 AC Waveforms VIN NC COM VOUT NO IN Logic Input RL 50Ω CL 35pF Logic Input 50% VOUT GND 0.9 x VOUT tBBM Figure 3. Break Before Make Interval Timing 561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480)632-1715 www.protekanalog.com 95252 REV0. 05/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS PA2223 LoPro Dual SPDT Analog Switch ™ ANALOG PRODUCTS DIVISION RGEN COM NC or NO VGEN Logic Input VOUT On Off Off CL IN ∆VOUT 1nF Q= (∆VOUT)(CL) GND Logic Input Figure 4. Charge Injection Test VCC VCC 10nF 50Ω 10nF 50Ω COM NC COM Signal Generator Logic Input 0V or VIH IN Signal Generator NO NO / NC GND 50Ω GND Analyzer IN Analyzer CL 5pF CL 5pF RL 50Ω Figure 5. Off Isolation RL 50Ω Figure 6. Crosstalk VCC VCC 10nF 10nF COM Capacitance Meter Capacitance Meter IN Logic Input 0V or VIH f = 1MHz COM f = 1MHz IN NO / NC NO / NC GND Figure 7. Channel Off Capacitance GND Figure 8. Channel On Capacitance 561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480)632-1715 www.protekanalog.com 95252 REV0. 05/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS Logic Input 0V or VIH PA2223 LoPro Dual SPDT Analog Switch ™ ANALOG PRODUCTS DIVISION VCC 10nF 50Ω NC / NO COM Analyzer Signal Generator Logic Input 0V or VIH IN 50Ω GND Figure 9. Bandwidth 561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480)632-1715 www.protekanalog.com 95252 REV0. 05/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS PA2223 LoPro Dual SPDT Analog Switch ™ ANALOG PRODUCTS DIVISION Package Layout and Dimensions Bottom View Top View D E DIM MIN TYP Max A 1.25 1.30 1.35 B 1.55 1.60 1.65 C 0.50 0.55 0.60 D A Pin1 G g Pin 1 Area F f B Front View 0.40 E 0.29 0.30 0.31 F 0.49 0.50 0.51 G 0.80 REF c 0.00 - 0.05 c1 0.10 REF f 0.15 0.20 0.25 g 0.59 0.60 0.61 Note: Package Dimensions in millimeters C Recommended Land Pattern c1 0.25 0.50 Pad 1 0.75 0.70 1.60 0.40 1.90 Tape and Reel Specifications Reel Dia A0 B0 K0 D E F W P0 P2 P t-max 178 (7”) 1.47±0.05 1.73±0.05 0.65±0.05 1.50±0.10 1.75±0.10 3.50±0.05 12.00±0.30 4.00±0.10 2.00±0.05 4.00±0.10 0.25 P0 P2 D t 10 Pitches Cumulative Tolerance on Tape± 0.2 E Pin 1 indicated by Dot Top cover tape A0 B0 W 223 223 223 K0 F P 561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480)632-1715 www.protekanalog.com 95252 REV0. 05/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS ANALOG PRODUCTS DIVISION PA2223 LoPro Dual SPDT Analog Switch ™ Life Support Policy PROTEK ANALOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF PROTEK DEVICES. 561 E. Elliot Road #175, Chandler, AZ 85225 Tel: (480) 539-2900. Fax: (480)632-1715 www.protekanalog.com 95252 REV0. 05/10 NOT FOR USE IN LIFE SUPPORT SYSTEMS