PC817XJ0000F Series DIP 4pin General Purpose Photocoupler PC817XJ0000F Series ∗ 4-channel package type is also available. (model No. PC847XJ0000F Series) ■ Description ■ Agency approvals/Compliance PC817XJ0000F Series contains an IRED optically coupled to a phototransistor. It is packaged in a 4pin DIP, available in wide-lead spacing option and SMT gullwing lead-form option. Input-output isolation voltage(rms) is 5.0kV. Collector-emitter voltage is 80V and CTR is 50% to 600% at input current of 5mA. 1. Recognized by UL1577 (Double protection isolation), file No. E64380 (as model No. PC817) 2. Package resin : UL flammability grade (94V-0) ■ Applications 1. I/O isolation for MCUs (Micro Controller Units) 2. Noise suppression in switching circuits 3. Signal transmission between circuits of different potentials and impedances ■ Features 1. 4pin DIP package 2. Double transfer mold package (Ideal for Flow Soldering) 3. High collector-emitter voltage (VCEO:80V) 4. Current transfer ratio (CTR : MIN. 50% at IF=5 mA, VCE=5V) 5. Several CTR ranks available 6. High isolation voltage between input and output (Viso(rms) : 5.0 kV) 7. Lead-free and RoHS directive compliant Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 1 Sheet No.: D2-A03102EN Date Jun. 30. 2005 © SHARP Corporation PC817XJ0000F Series ■ Internal Connection Diagram Anode Cathode Emitter Collector 1 1 4 2 3 2 3 4 ■ Outline Dimensions (Unit : mm) PC817 2 Date code 4 1 PC817 2 2.54±0.25 3 Factory identification mark 6.5±0.5 3 6.5±0.5 7.62±0.3 0.26 ±0.1 0.26 0.5TYP. 3.5±0.5 3.0±0.5 2.7±0.5 Epoxy resin ±0.1 4.58±0.5 0.35±0.25 4.58±0.5 7.62±0.3 Epoxy resin 1.0+0.4 −0 3.5±0.5 4.58±0.5 1 0.6±0.2 1.2±0.3 0.6±0.2 Date code 4 Rank mark Anode mark Factory identification mark 4.58±0.5 Rank mark Anode mark 1.2±0.3 2. SMT Gullwing Lead-Form [ex. PC817XIJ000F] 2.54±0.25 1. Through-Hole [ex. PC817XJ0000F] 2.54±0.25 1.0+0.4 −0 10.0+0 −0.5 0.5±0.1 θ Product mass : approx. 0.23g Product mass : approx. 0.22g 3. Wide Through-Hole Lead-Form [ex. PC817XFJ000F] Rank mark 4. Wide SMT Gullwing Lead-Form [ex. PC817XFPJ00F] Rank mark Factory identification mark 1 4 0.6±0.2 1.2±0.3 Date code Date code 1 4 3.5±0.5 2.7 MIN. 2.54 ±0.25 6.5±0.5 7.62±0.3 4.58±0.5 3 4.58±0.5 0.26 7.62±0.3 PC817 ±0.1 2 0.25±0.25 6.5±0.5 3 1.0±0.1 PC817 2.54±0.25 1.0±0.1 2 4.58 ±0.5 0.6±0.2 1.2±0.3 Factory identification mark Anode mark Anode mark 3.5±0.5 θ : 0 to 13˚ 4.58±0.5 θ Epoxy resin ±0.25 0.75 Epoxy resin ±0.5 10.16 0.5±0.1 ±0.25 0.75 12.0MAX 0.26±0.1 0.5±0.1 ±0.5 10.16 Product mass : approx. 0.23g Product mass : approx. 0.22g Sheet No.: D2-A03102EN 2 PC817XJ0000F Series Date code (2 digit) A.D. 1990 1991 1992 1993 1994 1995 1996 1997 1998 1999 2000 2001 1st digit Year of production A.D Mark 2002 A 2003 B 2004 C 2005 D 2006 E 2007 F 2008 H 2009 J 2010 K 2011 L 2012 M ·· N · 2nd digit Month of production Month Mark January 1 February 2 March 3 April 4 May 5 June 6 July 7 August 8 September 9 October O November N December D Mark P R S T U V W X A B C ·· · repeats in a 20 year cycle Factory identification mark and Plating material Factory identification Mark Country of origin Plating material Japan SnCu (Cu : TYP. 2%) Indonesia SnBi (Bi : TYP. 2%) China SnCu (Cu : TYP. 2%)* no mark * Up to Date code "T4" (April 2005), SnBi (Bi : TYP. 2%). ** This factory marking is for identification purpose only. Please contact the local SHARP sales representative to see the actural status of the production. Rank mark Refer to the Model Line-up table Sheet No.: D2-A03102EN 3 PC817XJ0000F Series ■ Absolute Maximum Ratings Output Input Parameter Symbol Forward current IF *1 Peak forward current IFM Reverse voltage VR Power dissipation P Collector-emitter voltage VCEO Emitter-collector voltage VECO IC Collector current Collector power dissipation PC Total power dissipation Ptot *2 Isolation voltage Viso (rms) Operating temperature Topr Storage temperature Tstg *3 Soldering temperature Tsol Rating 50 1 6 70 80 6 50 150 200 5.0 −30 to +100 −55 to +125 260 (Ta=25˚C) Unit mA A V mW V V mA mW mW kV ˚C ˚C ˚C *1 Pulse width≤100µs, Duty ratio : 0.001 *2 40 to 60%RH, AC for 1minute, f=60Hz *3 For 10s Transfer characteristics Output Input ■ Electro-optical Characteristics Parameter Forward voltage Peak forward voltage Reverse current Terminal capacitance Collector dark current Collector-emitter breakdown voltage Emitter-collector breakdown voltage Collector current Collector-emitter saturation voltage Isolation resistance Floating capacitance Cut-off frequency Rise time Response time Fall time Symbol VF VFM IR Ct ICEO BVCEO BVECO IC VCE (sat) RISO Cf fc tr tf Conditions IF=20mA IFM=0.5A VR=4V V=0, f=1kHz VCE=50V, IF=0 IC=0.1mA, IF=0 IE=10µA, IF=0 IF=5mA, VCE=5V IF=20mA, IC=1mA DC500V, 40 to 60%RH V=0, f=1MHz VCE=5V, IC=2mA, RL=100Ω, −3dB VCE=2V, IC=2mA, RL=100Ω MIN. − − − − − 80 6 2.5 − 5×1010 − − − − TYP. 1.2 − − 30 − − − − 0.1 1×1011 0.6 80 4 3 MAX. 1.4 3.0 10 250 100 − − 30.0 0.2 − 1.0 − 18 18 (Ta=25˚C) Unit V V µA pF nA V V mA V Ω pF kHz µs µs Sheet No.: D2-A03102EN 4 PC817XJ0000F Series ■ Model Line-up Lead Form Through-Hole Package Model No. Lead Form Wide Through-Hole Rank mark IC [mA] (IF=5mA, VCE=5V, Ta=25˚C) PC817XFJ000F PC817XF1J00F PC817XF2J00F PC817XF3J00F PC817XF4J00F PC817XF5J00F PC817XF6J00F PC817XF7J00F PC817XF8J00F PC817XF9J00F PC817XF0J00F with or without A B C D A or B B or C C or D A, B or C B, C or D A, B, C or D 2.5 to 30.0 4.0 to 8.0 6.5 to 13.0 10.0 to 20.0 15.0 to 30.0 4.0 to 13.0 6.5 to 20.0 10.0 to 30.0 4.0 to 20.0 6.5 to 30.0 4.0 to 30.0 Wide SMT Gullwing Taping 2 000pcs/reel Rank mark IC [mA] (IF=5mA, VCE=5V, Ta=25˚C) Sleeve 100pcs/sleeve PC817XJ0000F PC817X1J000F PC817X2J000F PC817X3J000F PC817X4J000F PC817X5J000F PC817X6J000F PC817X7J000F PC817X8J000F PC817X9J000F PC817X0J000F SMT Gullwing Package Sleeve 100pcs/sleeve Model No. PC817XIJ000F PC817XI1J00F PC817XI2J00F PC817XI3J00F PC817XI4J00F PC817XI5J00F PC817XI6J00F PC817XI7J00F PC817XI8J00F PC817XI9J00F PC817XI0J00F PC817XPJ000F PC817XFPJ00F with or without A PC817XP1J00F − B PC817XP2J00F − C PC817XP3J00F − D − PC817XP4J00F A or B − PC817XP5J00F B or C − PC817XP6J00F C or D − PC817XP7J00F − A, B or C PC817XP8J00F − B, C or D PC817XP9J00F − A, B, C or D PC817XP0J00F 2.5 to 30.0 4.0 to 8.0 6.5 to 13.0 10.0 to 20.0 15.0 to 30.0 4.0 to 13.0 6.5 to 20.0 10.0 to 30.0 4.0 to 20.0 6.5 to 30.0 4.0 to 30.0 Please contact a local SHARP sales representative to inquire about production status. Sheet No.: D2-A03102EN 5 PC817XJ0000F Series Fig.2 Diode Power Dissipation vs. Ambient Temperature Fig.1 Forward Current vs. Ambient Temperature 100 Diode power dissipation P (mW) Forward current IF (mA) 50 40 30 20 10 0 −30 0 25 50 55 75 100 80 70 60 40 20 0 −30 125 0 Fig.3 Collector Power Dissipation vs. Ambient Temperature Total Power dissipation Ptot (mW) Collector power dissipation PC (mW) 75 100 125 250 200 150 100 50 0 −30 0 25 50 75 100 200 150 100 50 0 −30 125 0 25 50 75 100 125 Ambient temperature Ta (˚C) Ambient temperature Ta (˚C) Fig.5 Peak Forward Current vs. Duty Ratio Fig.6 Current Transfer Ratio vs. Forward Current 10 000 500 Pulse width≤100µs Ta=25˚C VCE=5V Ta=25˚C Current transfer ratio CTR (%) Peak forward current IFM (mA) 50 55 Fig.4 Total Power Dissipation vs. Ambient Temperature 250 1 000 100 10 25 Ambient temperature Ta (˚C) Ambient temperature Ta (˚C) 10−3 10−2 10−1 400 300 200 100 0 0.1 1 Duty ratio 1 10 Forward current IF (mA) 100 Sheet No.: D2-A03102EN 6 PC817XJ0000F Series Fig.7 Forward Current vs. Forward Voltage Fig.8 Collector Current vs. Collector-emitter Voltage 30 Ta=75˚C IF=30mA 25˚C 0˚C 50 −25˚C 25 Collector current IC (mA) Forward current IF (mA) 50˚C 100 20 10 5 Ta=25˚C 20mA PC (MAX.) 20 15 10mA 10 5mA 5 2 1 0 0 0.5 1 1.5 2 2.5 3 0 3.5 1 Fig.9 Relative Current Transfer Ratio vs. Ambient Temperature Collector-emitter saturation voltage VCE (sat) (V) Relative current transfer ratio (%) 5 6 0.14 IF=1mA,VCE=5V IF=5mA,VCE=5V 100 50 −20 0 20 40 7 8 9 60 80 IF=20mA IC=1mA 0.12 0.1 0.08 0.06 0.04 0.02 0 −40 100 Ambient temperature Ta (˚C) −20 0 20 40 60 80 100 Ambient temperature Ta (˚C) Fig.11 Collector Dark Current vs. Ambient Temperature Fig.12 Collector-emitter Saturation Voltage vs. Forward Current 10−5 6 Collector-emitter saturation voltage VCE (sat) (V) VCE=50V 10−6 Collector dark current ICEO (A) 4 Fig.10 Collector - emitter Saturation Voltage vs. Ambient Temperature 150 10−7 10−8 10−9 10−10 10−11 −30 3 Collector-emitter voltage VCE (V) Forward voltage VF (V) 0 −40 2 Ta=25˚C 5 IC=0.5mA 1mA 4 3mA 5mA 3 7mA 2 1 0 0 20 40 60 80 Ambient temperature Ta (˚C) 0 100 5 10 15 Forward current IF (mA) Sheet No.: D2-A03102EN 7 PC817XJ0000F Series Fig.13 Response Time vs. Load Resistance 100 Fig.14 Test Circuit for Response Time VCE=2V IC=2mA Ta=25˚C Output Response time (µs) tr Input tf RD RL 10% Output 90% VCE 10 ts td tr tf td ts 1 0.1 0.01 Please refer to the conditions in Fig.13. 0.1 1 10 Load resistance RL (kΩ) Fig.15 Frequency Response Fig.16 Test Circuit for Frequency Response VCC VCE=5V IC=2mA Ta=25˚C 0 Voltage gain Av (dB) Input VCC RD RL Output VCE 100Ω 1kΩ −10 Please refer to the conditions in Fig.15. RL=10kΩ −20 1 10 100 Frequency f (kHz) Remarks : Please be aware that all data in the graph are just for reference and not for guarantee. Sheet No.: D2-A03102EN 8 PC817XJ0000F Series ■ Design Considerations ● Design guide While operating at IF<1.0mA, CTR variation may increase. Please make design considering this fact. This product is not designed against irradiation and incorporates non-coherent IRED. ● Degradation In general, the emission of the IRED used in photocouplers will degrade over time. In the case of long term operation, please take the general IRED degradation (50% degradation over 5 years) into the design consideration. ● Recommended Foot Print (reference) SMT Gullwing Lead-form Wide SMT Gullwing Lead-form 10.2 1.7 1.7 2.54 2.54 8.2 2.2 2.2 (Unit : mm) ✩ For additional design assistance, please review our corresponding Optoelectronic Application Notes. Sheet No.: D2-A03102EN 9 PC817XJ0000F Series ■ Manufacturing Guidelines ● Soldering Method Reflow Soldering: Reflow soldering should follow the temperature profile shown below. Soldering should not exceed the curve of temperature profile and time. Please don't solder more than twice. (˚C) 300 Terminal : 260˚C peak ( package surface : 250˚C peak) 200 Reflow 220˚C or more, 60s or less Preheat 150 to 180˚C, 120s or less 100 0 0 1 2 3 4 (min) Flow Soldering : Due to SHARP's double transfer mold construction submersion in flow solder bath is allowed under the below listed guidelines. Flow soldering should be completed below 270˚C and within 10s. Preheating is within the bounds of 100 to 150˚C and 30 to 80s. Please don't solder more than twice. Hand soldering Hand soldering should be completed within 3s when the point of solder iron is below 400˚C. Please don't solder more than twice. Other notices Please test the soldering method in actual condition and make sure the soldering works fine, since the impact on the junction between the device and PCB varies depending on the tooling and soldering conditions. Sheet No.: D2-A03102EN 10 PC817XJ0000F Series ● Cleaning instructions Solvent cleaning: Solvent temperature should be 45˚C or below Immersion time should be 3 minutes or less Ultrasonic cleaning: The impact on the device varies depending on the size of the cleaning bath, ultrasonic output, cleaning time, size of PCB and mounting method of the device. Therefore, please make sure the device withstands the ultrasonic cleaning in actual conditions in advance of mass production. Recommended solvent materials: Ethyl alcohol, Methyl alcohol and Isopropyl alcohol In case the other type of solvent materials are intended to be used, please make sure they work fine in actual using conditions since some materials may erode the packaging resin. ● Presence of ODC This product shall not contain the following materials. And they are not used in the production process for this product. Regulation substances : CFCs, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methylchloroform) Specific brominated flame retardants such as the PBBOs and PBBs are not used in this product at all. This product shall not contain the following materials banned in the RoHS Directive (2002/95/EC). •Lead, Mercury, Cadmium, Hexavalent chromium, Polybrominated biphenyls (PBB), Polybrominated diphenyl ethers (PBDE). Sheet No.: D2-A03102EN 11 PC817XJ0000F Series ■ Package specification ● Sleeve package 1. Through-Hole or SMT Gullwing Lead-Form Package materials Sleeve : HIPS (with anti-static material) Stopper : Styrene-Elastomer Package method MAX. 100pcs of products shall be packaged in a sleeve. Both ends shall be closed by tabbed and tabless stoppers. The product shall be arranged in the sleeve with its anode mark on the tabless stopper side. MAX. 20 sleeves in one case. Sleeve outline dimensions 12.0 ±2 5.8 10.8 520 6.7 (Unit : mm) 2. Wide Through-Hole Lead-Form or Wide SMT Gullwing Lead-Form Package materials Sleeve : HIPS (with anti-static material) Stopper : Styrene-Elastomer Package method MAX. 100pcs of products shall be packaged in a sleeve. Both ends shall be closed by tabbed and tabless stoppers. The product shall be arranged in the sleeve with its anode mark on the tabless stopper side. MAX. 20 sleeves in one case. Sleeve outline dimensions 15.0 ±2 5.9 10.8 520 6.35 (Unit : mm) Sheet No.: D2-A03102EN 12 PC817XJ0000F Series ● Tape and Reel package 1. SMT Gullwing Package materials Carrier tape : PS Cover tape : PET (three layer system) Reel : PS Carrier tape structure and Dimensions D F J G I H X. MA H A B C E Dimensions List A B 16.0±0.3 7.5±0.1 H I ±0.1 10.4 0.4±0.05 5˚ K C 1.75±0.1 J 4.2±0.1 D 8.0±0.1 K 5.1±0.1 E 2.0±0.1 (Unit : mm) F G +0.1 4.0±0.1 φ1.5−0 Reel structure and Dimensions e d c g Dimensions List a b 330 e 23±1.0 f a b 17.5±1.5 f 2.0±0.5 (Unit : mm) c d ±1.0 100 13±0.5 g 2.0±0.5 Direction of product insertion Pull-out direction [Packing : 2 000pcs/reel] Sheet No.: D2-A03102EN 13 PC817XJ0000F Series 2. Wide SMT Gullwing Package materials Carrier tape : PS Cover tape : PET (three layer system) Reel : PS Carrier tape structure and Dimensions F D G E I J 5˚ MA X. H H A B C K Dimensions List A B 24.0±0.3 11.5±0.1 H I ±0.1 12.4 0.4±0.05 C 1.75±0.1 J 4.1±0.1 D 8.0±0.1 K 5.1±0.1 E 2.0±0.1 (Unit : mm) F G +0.1 4.0±0.1 φ1.5−0 Reel structure and Dimensions e d c g Dimensions List a b a 330 e 23±1.0 f b 25.5±1.5 f 2.0±0.5 (Unit : mm) c d ±1.0 100 13±0.5 g 2.0±0.5 Direction of product insertion Pull-out direction [Packing : 2 000pcs/reel] Sheet No.: D2-A03102EN 14 PC817XJ0000F Series ■ Important Notices with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). · The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. · Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. · If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is necessary to obtain approval to export such SHARP devices. · Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection · This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. · Contact and consult with a SHARP representative if there are any questions about the contents of this publication. [E178] Sheet No.: D2-A03102EN 15