05121 PP0640EA thru PP3500EC . . . engineered solutions for the transient environment™ BIDIRECTIONAL THYRISTOR SURGE SUPPRESSOR APPLICATIONS ✔ T1/E1 Trunk & Line Card ✔ SLIC Line Card ✔ DBX Branch Exchange Switches ✔ FCC Part 68 Customer Premise Equipment ✔ Line Interface Modem ✔ xDSL Architecture Interface ✔ ISDN Architecture Interface TO-92 IEC COMPATIBILITY (EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns ✔ 61000-4-5 (Surge): 24A, 8/20µs - Level 2(Line-Gnd) & Level 3(Line-Line) DEVICE SYMBOL (BIDIRECTIONAL) FEATURES ✔ Complies with: FCC Part 68, UL 1459, Bellcore 1089, ITU-K.20 & K.21 ✔ Peak Off-State Voltage from 58 to 300 Volts ✔ Surge Current Capability(See Table 1) ✔ ESD Protection > 40 kilovolts ✔ Low Capacitance for T1/E1 Trunk & Line Card Applications MECHANICAL CHARACTERISTICS ✔ Molded TO-92 Package ✔ Weight 0.18 grams (Approximate) ✔ Flammability Rating UL 94V-0 ✔ Device Marking: Logo & Marking Code TABLE 1 - SURGE RATINGS SERIES IPP 2 X 10µs AMPS EA EB EC 125 300 500 IPP IPP IPP 10 X 160µs 10 X 560µs 10 X 1000µs AMPS AMPS AMPS 100 150 200 50 100 200 50 75 100 ITSM 60 Hz AMPS 20 32 60 di/dt dv/dt AMPS/µs AMPS/µs (See Note 1) (See Note 1) 500 500 500 2000 2000 2000 Note 1: Critital Rate of Rise for On-State Current (di/dt) and Off-State Voltage (dv/dt). 05121.R1 4/02 1 www.protekdevices.com PP0640EA thru PP3500EC DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25°C Unless Otherwise Specified SYMBOL VALUE UNITS ITSM 60 Amps Junction Temperature Tj -40 to 150 °C Storage Temperature T STG -55 to 150 °C Thermal Resistance(Junction) - EA & EB Series Rqjc 28 °C/Watt Thermal Resistance(Junction) - EC Series Rqjc 26 °C/Watt Thermal Resistance(Ambient) - EA & EB Series Rqjc 90 °C/Watt Thermal Resistance(Ambient) - EC Series Rqjc 85 °C/Watt PARAMETER Surge Current - 50/60 Hz ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified PART NUMBER (See Note 1) DEVICE MARKING CODE REPETITIVE PEAK OFF-STATE VOLTAGE SWITCHING VOLTAGE MINIMUM HOLDING CURRENT (See Fig. 4) VDRM VOLTS @100V/µs VS VOLTS di/dt = 1A/ms IH mA SWITCHING CURRENT MAXIMUM OFF-STATE VOLTAGE (See Fig. 3) MAXIMUM ON-STATE VOLTAGE (See Fig. 3) ON-STATE CURRENT TYPICAL CAPACITANCE (See Note 2) IS mA @VDRM IDRM µA @IT VT VOLTS IT AMPS @2V, 1 MHz C pF PP0640EA PP0720EA PP0800EA PP1100EA PP1300EA* PP1500EA PP1800EA PP2300EA* PP2600EA* PP3100EA PP3500EA GC GD GE GF GG GH GI GJ GK GL GM 58 65 75 90 120 140 160 190 220 275 300 77 88 98 130 160 180 220 260 300 350 400 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 60 60 60 60 40 40 40 30 30 30 30 PP0640EB* PP0720EB PP0800EB PP1100EB PP1300EB PP1500EB* PP1800EB PP2300EB PP2600EB PP3100EB* PP3500EB* GP GQ GR GS GT GU GV GW GX GY GZ 58 65 75 90 120 140 160 190 220 275 300 77 88 98 130 160 180 220 260 300 350 400 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 60 60 60 60 40 40 40 30 30 30 30 PP0640EC* PP0720EC PP0800EC PP1100EC PP1300EC* PP1500EC* PP1800EC PP2300EC* PP2600EC PP3100EC* PP3500EC* HC HD HE HF HG HH HI HJ HK HL HM 58 65 75 90 120 140 160 190 220 275 300 77 88 98 130 160 180 220 260 300 350 400 150 150 150 150 150 150 150 150 150 150 150 800 800 800 800 800 800 800 800 800 800 800 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 120 120 120 120 80 80 80 60 60 60 60 Note 1: * Indicates preferred a part number. Note 2: Capacitance imbalance between positive and negative polarities is typically < 15pF. 05121.R1 4/02 2 www.protekdevices.com PP0640EA thru PP3500EC GRAPHS FIGURE 1 PULSE WAVE FORM IPP - Peak Pulse Current - % of IPP 100 FIGURE 2 V-I CHARACTERISTIC CURVE TEST WAVEFORM PARAMETERS tf = 10µs td = 1,000µs tf Peak Value IPP IPP ITSM IT IS IH VS td = t I /2 PP 50 IDRM VT VDRM -t e 0 0 1 2 3 t - Time - µs FIGURE 3 ON-STATE CURRENT VS SURGE CURRENT DURATION Non-Repetitive On-State Current (ITSM) - Amps 100 PPxxxxEA PPxxxxEC PPxxxxEB 10 1 1 05121.R1 4/02 10 100 Surge Current Duration - Full Cycles 3 1,000 www.protekdevices.com PP0640EA thru PP3500EC GRAPHS FIGURE 4 TYPICAL PEAK OFF-STATE CURRENT VS JUNCTION TEMPERATURE 100 IT - On-State Current - A IDRM - Peak Off-State Current - µA 10 1 0.1 0.01 -40 1.15 0 40 80 tJ- Temperature - °C 10 1 0 120 FIGURE 6 TYPICAL NORMALIZED VS VS JUNCTION TEMPERATURE 2.5 1.1 FIGURE 5 TYPICAL ON-STATE CURRENT VS ON-STATE VOLTAGE 1 2 3 4 VT - On-State Voltage - V 5 6 7 FIGURE 7 TYPICAL HOLDING CURRENT VS JUNCTION TEMPERATURE 2 IH/IH (tJ 25°C) Normalized VS 1.05 1 0.95 1.5 1 0.9 0.5 0.85 0.8 -40 05121.R1 4/02 0 40 80 tJ- Temperature - °C 0 -40 120 4 0 40 80 tJ- Temperature - °C 120 www.protekdevices.com PP0640EA thru PP3500EC APPLICATION NOTES FIGURE 1: UL 1459 & FCC Part 68 - Metallic Protection Fuse RTip TIP The TSS (Thyristor Surge Suppressor) device is located across the tip-to-ring after a limiting resistor and fuse combination. RTIP and RRING resistors are optional depending upon the TSS device selection. Without the resistors, the PP3100EB/EC is recommended. However, with a resistance value of 7.5 Ohms for tip and ring, the PP3100EA is recommended. Digital signals may use a lower TSS device depending upon the total tip to ring voltage range. Selection of the TSS device, either PPxxxxEA or EB/EC is based upon the value of the tip and ring resistors. For the National Electric Code (NEC) article 800, it is recommended that at least one fuse be used in the tip or ring line for metallic surges. Fuses may be replaced with a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device. To Protected Equipment RRing RING FIGURE 1 - Metallic Protection R Tip TIP FIGURE 2 - UL 1459 & FCC Part 68 - Longitudinal Protection There are two TSS devices, one located from tip-to-ground and one ring-to-ground. For standard analog signals, the PP3100EA is recommended with a typical resistor value for tip and ring of 15 Ohms. The PP3100EB/EC is recommended for resistor values of 7.5 Ohms each. The National Electric Code (NEC) article 800 requires two fuse elements when connecting to ground. Fuses or a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device may be used. The purpose of this circuit is to limit AC power current from getting on the ground line causing any safety hazard. To Protected Equipment R Ring RING FIGURE 2 - Longitudinal Protection FIGURE 3 - UL 1459 & FCC Part 68 - Metallic & Longitudinal Protection Three equal TSS devices are used in this application for metallic (tipto-ring) and longitudinal (tip-to-ground and ring-to-ground) protection. For analog signals, the PP3100EB/EC is recommended. With a resistance value of 15 Ohms for the tip and ring resistors, the PP3100EA may be used. The National Electric Code (NEC) article 800 requires two fuse elements when connecting to ground. Fuses or a suitable Positive Temperature Coefficient (PTC) automatic resettable current limiting device may be used. This circuit is recommended for protection against the Bellcore requirement: First Level Lightning Surge Tests (Telecommunications Port), document # GR-1089-CORE. R Tip TIP To Protected Equipment R Ring RING FIGURE 3 - Metallic & Longitudinal Protection 05121.R1 4/02 5 www.protekdevices.com PP0640EA thru PP3500EC PACKAGE OUTLINE & DIMENSIONS PACKAGE OUTLINE TO-92 TC MEASURING POINT A N DIMENSIONS DIM A B D E F G H J K L M N B PIN 1 PIN 3 E M H G L F D MILLIMETERS MIN MAX 4.47 12.70 2.41 3.81 1.16 3.43 2.23 4.47 2.23 0.38 0.33 - 4.98 2.67 1.37 3.68 2.44 4.73 2.44 0.51 0.43 1.52 INCHES MIN MAX 0.176 0.500 0.095 0.150 0.046 0.135 0.088 0.176 0.088 0.015 0.013 - 0.196 0.105 0.054 0.145 0.096 0.186 0.096 0.020 0.017 0.060 NOTES: 1. All leads insulate from case. Case is electrically nonconductive. K J 06031 Rev 0 - 4/02 ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: [email protected] Web Site: www.protekdevices.com COPYRIGHT © ProTek Devices 2001 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. 05121.R1 4/02 6 www.protekdevices.com