DATA SHEET PHOTOCOUPLER PS9701 HIGH SPEED DIGITAL OUTPUT TYPE 5-PIN SOP PHOTOCOUPLER −NEPOC TM Series− DESCRIPTION The PS9701 is an optically coupled isolator containing a GaAlAs LED on light emitting side (input side) and a photodiode and a signal processing circuit on light receiving side (output side) on one chip. This is SOP (Small Outline Package) type for high-density applications. FEATURES • High isolation voltage (BV = 2 500 Vr.m.s.) • Small and thin package (5-pin SOP) • High-speed response (tPHL = 36 ns TYP., tPLH = 60 ns TYP.) • Low threshold input current (IFHL = 2.5 mA TYP.) • Open-collector type • Ordering number of taping product: PS9701-1-E3, E4, F3, F4 • UL approved: File No. E72422 (S) • VDE0884 approved (Option) APPLICATIONS • Computer and peripheral manufactures • Measurement equipment • Audio-Visual The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. P11437EJ4V0DS00 (4th edition) Date Published September 1999 NS CP(K) Printed in Japan The mark • shows major revised points. © 1994, 1999 PS9701 PACKAGE DIMENSIONS in millimeters 4.0±0.5 TOP VIEW 6 5 4 1. Anode 3. Cathode 4. GND 5. VO 6. VCC 1 3 7.0±0.3 2 0.15 +0.10 –0.05 2.0 0.1±0.1 2.1±0.2 4.4 0.5±0.3 1.27 0.4 +0.10 –0.05 0.25 M Data Sheet P11437EJ4V0DS00 PS9701 ORDERING INFORMATION Part Number PS9701 Package 5-pin SOP PS9701-E3 Safety Standards Approval Packing Style Magazine case 100 pcs UL approved Application Part *1 Number PS9701 Embossed Tape 900 pcs/reel PS9701-E4 PS9701-F3 Embossed Tape 3 500 pcs/reel PS9701-F4 PS9701-V Magazine case 100 pcs VDE0884 approved PS9701-V-E3 Embossed Tape 900 pcs/reel PS9701-V-E4 PS9701-V-F3 Embossed Tape 3 500 pcs/reel PS9701-V-F4 *1 For the application of the Safety Standard, following part number should be used. ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, unless otherwise specified) Parameter Symbol Ratings Unit Forward Current IF 30 mA Reverse Voltage VR 5 V Supply Voltage VCC 7 V Output Voltage VO 7 V Output Current IO 50 mA Power Dissipation PC 85 mW Isolation Voltage BV 2 500 Vr.m.s. Operating Ambient Temperature TA –40 to +85 °C Storage Temperature Tstg –55 to +125 °C Diode Detector *1 *1 AC voltage for 1 minute at TA = 25 °C, RH = 60 % between input and output RECOMMENDED OPERATING CONDITIONS Parameter Symbol MIN. Low Level Input Current IFL 0 High Level Input Current IFH 5 Supply Voltage VCC Operating Ambient Temperature TA TYP. MAX. Unit 250 µA 7.5 15 mA 4.5 5.0 5.5 V 0 25 70 °C Remark By-pass capacitor of more than 0.1 µF is used between VCC and GND near the device. Data Sheet P11437EJ4V0DS00 3 PS9701 ELECTRICAL CHARACTERISTICS (TA = 0 to +70 °C, unless otherwise specified) Parameter Diode Symbol Conditions MIN. TYP. MAX. Unit 1.4 1.65 1.9 V 10 µA Forward Voltage VF IF = 10 mA, TA = 25 °C Reverse Current IR VR = 5 V, TA = 25 °C Terminal Capacitance Ct V = 0 V, f = 1 MHz, TA = 25 °C 60 IOH VCC = VO = 5.5 V, IF = 250 µA 2 250 µA Low Level Output Voltage VOL VCC = 5.5 V, IF = 7.5 mA, IO = 13 mA 0.3 0.6 V High Level Supply Current ICCH VCC = 5.5 V, IF = 0 mA 4 6 8 mA Low Level Supply Current ICCL VCC = 5.5 V, IF = 10 mA 9 12 15 mA 0.5 2.5 5.0 mA Detector High Level Output Current Coupled Threshold Input Current (H → L) TA = 25 °C IFHL pF VCC = 5 V, VO = 0.8 V, RL = 350 Ω Isolation Resistance RI-O VI-O = 1 kVDC, RH = 40 to 60 %, TA = 25 °C Isolation Capacitance 7 Ω 11 10 CI-O V = 0 V, f = 1 MHz, TA = 25 °C 0.6 Propagation Delay Time *1 (H → L) tPHL VCC = 5 V, IF = 7.5 mA, RL = 350 Ω, CL = 15 pF, TA = 25 °C 36 75 Propagation Delay Time *1 (L → H) tPLH 60 75 Rise Time tr 20 Fall Time tf 10 pF ns *1 Test circuit for propagation delay time 350 mV (IF = 7.5 mA) 175 mV (IF = 3.75 mA) IF Pulse Input 1 (PW = 1 µ s Duty Cycle = 1/10) 6 0.1 µF VCC = 5 V RL = 350 Ω 5 3 4 0 VO CL IF Monitor Input 5V Output 1.5 V VOL 51 Ω tPHL Remark CL is approximately 15 pF, which includes probe and stray wiring capacitance. 4 Data Sheet P11437EJ4V0DS00 tPLH PS9701 TYPICAL CHARACTERISTICS (TA = 25 °C, unless otherwise specified) POWER DISSIPATION vs. AMBIENT TEMPERATURE MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE 100 Power Dissipation PC (mW) Maximum Forward Current IF (mA) 50 40 30 20 10 0 20 40 60 80 100 20 40 60 80 100 FORWARD CURRENT vs. FORWARD VOLTAGE NORMALIZED THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE Normalized Threshold Input Current IFHL Forward Current IF (mA) 20 0 TA = 100 ˚C 50 ˚C 25 ˚C 0 ˚C –25 ˚C 1.0 0.1 1.2 1.6 1.4 1.8 2.0 2.2 2.4 1.6 Normalized to 1.0 1.4 at TA = 25 ˚C, VCC = 5 V, VO = 0.8 V, RL = 350 Ω 1.2 1.0 0.8 0.6 0.4 0.2 0.0 –50 –25 0 25 50 75 100 Forward Voltage VF (V) Ambient Temperature TA (˚C) OUTPUT VOLTAGE vs. FORWARD CURRENT LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE 1.50 7 Low Level Output Voltage VOL (V) 5V RL VO 6 Output Voltage VO (V) 40 Ambient Temperature TA (˚C) 10 5 4 RL = 100 Ω 3 350 Ω 1 kΩ 2 1 0 60 Ambient Temperature TA (˚C) 100 0.01 1.0 80 2 4 6 8 10 12 IF = 7.5 mA, VCC = 5.5 V 1.25 1.00 0.75 0.50 IOL = 13 mA 0.25 0.00 –50 5 mA –25 0 25 50 75 100 Ambient Temperature TA (˚C) Forward Current IF (mA) Data Sheet P11437EJ4V0DS00 5 PS9701 80 Propagation Delay Time tPHL, tPLH (ns) 1 000 tPLH 60 40 tPHL 20 0 Propagation Delay Time tPHL, tPLH (ns) PROPAGATION DELAY TIME vs. LOAD RESISTANCE 5 10 VCC = 5 V, RL = 350 Ω 20 25 15 500 50 tPHL 10 100 500 1 k 5 k 10 k 50 k PROPAGATION DELAY TIME vs. AMBIENT TEMPERATURE SWITCHING TIME vs. AMBIENT TEMPERATURE 25 IF = 7.5 mA, VCC = 5 V, RL = 350 Ω 100 80 tPLH 60 40 tPHL 20 –25 0 25 50 75 100 IF = 7.5 mA, VCC = 5 V, RL = 350 Ω 20 tr 15 10 tf 5 0 –50 Ambient Temperature TA (˚C) –25 0 25 50 75 Ambient Temperature TA (˚C) Remark The graphs indicate nominal characteristics. 6 tPLH 100 Load Resistance RL (Ω) 120 0 –50 IF = 7.5 mA, VCC = 5 V, PW = 1 µ s, duty 1/10 Forward Current IF (mA) Switching Time tr, tf (ns) Propagation Delay Time tPHL, tPLH (ns) PROPAGATION DELAY TIME vs. FORWARD CURRENT Data Sheet P11437EJ4V0DS00 100 PS9701 TAPING SPECIFICATIONS (in millimeters) 1.55±0.1 2.4±0.1 4.6±0.1 7.4±0.1 5.5±0.1 1.55±0.1 12.0±0.2 2.0±0.1 4.0±0.1 1.75±0.1 Outline and Dimensions (Tape) 0.3 8.0±0.1 Tape Direction PS9701-E3 PS9701-E4 Outline and Dimensions (Tape) 2.0 2.0±0.5 13.0±0.5 60 15˚ 15˚ 180 13.0±0.5 21.0±0.8 13.0±1.0 Packing: 900 pcs/reel Data Sheet P11437EJ4V0DS00 7 PS9701 1.55±0.1 2.4±0.1 4.6±0.1 7.4±0.1 5.5±0.1 1.55±0.1 12.0±0.2 2.0±0.1 4.0±0.1 1.75±0.1 Outline and Dimensions (Tape) 0.3 8.0±0.1 Tape Direction PS9701-F4 PS9701-F3 Outline and Dimensions (Reel) φ 330 2.0±0.5 1.5±0.5 60 ˚ φ 13.0±0.5 120 ˚ φ 80±5.0 φ 21.0±0.8 1.5 6.0±1 12.4+2.0 –0.0 Packing: 3 500 pcs/reel 8 Data Sheet P11437EJ4V0DS00 PS9701 RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering • Peak reflow temperature 235 °C (package surface temperature) • Time of temperature higher than 210 °C 30 seconds or less • Number of reflows Three • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) Package Surface Temperature T (˚C) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s 235 ˚C (peak temperature) 210 ˚C to 30 s 120 to 160 ˚C 60 to 90 s (preheating) Time (s) (2) Dip soldering • Temperature 260 °C or below (molten solder temperature) • Time 10 seconds or less • Number of times One • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) (3) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. Data Sheet P11437EJ4V0DS00 9 PS9701 SPECIFICATION OF VDE MARKS LICENSE DOCUMENT (VDE0884) Parameter Symbol Speck Unit Application classification (DIN VDE 0109) for rated line voltages ≤ 300 Vr.m.s. IV for rated line voltages ≤ 600 Vr.m.s. III Climatic test class (DIN IEC 68 Teil 1/09.80) 40/085/21 Dielectric strength maximum operating isolation voltage. Test voltage (partial discharge test procedure a for type test and random test) UIORM 710 Vpeak Upr = 1.2 × UIORM, Pd < 5 pC Upr 850 Vpeak Test voltage (partial discharge test procedure b for random test) Upr = 1.6 × UIORM, Pd < 5 pC Upr 1 140 Vpeak Highest permissible overvoltage UTR 4 000 Vpeak Degree of pollution (DIN VDE 0109) 2 Clearance distance >5 mm Creepage distance >5 mm Comparative tracking index (DIN IEC 112/VDE 0303 part 1) CTI Material group (DIN VDE 0109) 175 III a Storage temperature range Tstg –55 to +125 °C Operating temperature range TA –40 to +85 °C Ris MIN. 10 Isolation resistance, minimum value VIO = 500 V dc at TA = 25 °C VIO = 500 V dc at TA MAX. at least 100 °C 12 Ω 11 Ris MIN. 10 Ω Package temperature Tsi 150 °C Current (input current IF, Psi = 0) Isi 200 mA Power (output or total power dissipation) Psi 300 mW Ris MIN. 10 Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Isolation resistance VIO = 500 V dc at TA = 175 °C (Tsi) 10 Data Sheet P11437EJ4V0DS00 9 Ω PS9701 [MEMO] Data Sheet P11437EJ4V0DS00 11 PS9701 CAUTION Within this device there exists GaAs (Gallium Arsenide) material which is a harmful substance if ingested. Please do not under any circumstances break the hermetic seal. NEPOC is a trademark of NEC Corporation. • The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. • No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. • NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. • Descriptions of circuits, software, and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software, and information in the design of the customer's equipment shall be done under the full responsibility of the customer. NEC Corporation assumes no responsibility for any losses incurred by the customer or third parties arising from the use of these circuits, software, and information. • While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. • NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. M7 98. 8