05095 PSMS05 thru PSMS24C Only One Name Means ProTek’Tion™ STANDARD CAPACITANCE TVS ARRAY APPLICATIONS ✔ Ethernet - 10 Base T ✔ Cellular Phones ✔ Handheld Electronics ✔ FireWire & USB Interfaces IEC COMPATIBILITY (EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns ✔ 61000-4-5 (Surge): 12A, 8/20µs - Level 1(Line-Gnd) & Level 2(Line-Line) SOT-23-6 FEATURES ✔ 350 Watts Peak Pulse Power per Line (tp=8/20µs) ✔ Monolithic Design ✔ Available in Multiple Voltage Types Ranging From 5V to 24V ✔ Protect 4 Lines ✔ ESD Protection > 25 kilovolts ✔ Low Clamping Voltage ✔ Unidirectional & Bidirectional Configurations ✔ Low Leakage Current MECHANICAL CHARACTERISTICS ✔ Molded JEDEC SOT-23-6 Package ✔ Weight 0.6 grams (Approximate) ✔ Flammability rating UL 94V-0 ✔ 8mm Tape and Reel Per EIA Standard 481 ✔ Marking: Marking Code & Pin One Defined By DOT on Package PIN CONFIGURATIONS UNIDIRECTIONAL 05095.R3 9/03 BIDIRECTIONAL 1 6 1 6 2 5 2 5 3 4 3 4 1 www.protekdevices.com PSMS05 thru PSMS24C DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25°C Unless Otherwise Specified SYMBOL VALUE UNITS Peak Pulse Power (tp = 8/20µs) - See Figure 1 PPP 350 Watts Operating Temperature TJ -55°C to 150°C °C TSTG -55°C to 150°C °C PARAMETER Storage Temperature ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified PART NUMBER (See Notes 1-3) PSMS05 PSMS05C PSMS12 PSMS12C PSMS15 PSMS15C PSMS24 PSMS24C DEVICE MARKING PRH PRL PRI PRM PRJ PRN PRK PRO RATED STAND-OFF VOLTAGE MINIMUM BREAKDOWN VOLTAGE MAXIMUM CLAMPING VOLTAGE (See Fig. 2) MAXIMUM CLAMPING VOLTAGE (See Fig. 2) V WM VOLTS @ 1mA V(BR) VOLTS @ IP = 1A VC VOLTS 5.0 5.0 12.0 12.0 15.0 15.0 24.0 24.0 6.0 6.0 13.3 13.3 16.7 16.7 26.7 26.7 9.8 9.8 19 19 24 24 40 40 MAXIMUM LEAKAGE CURRENT TYPICAL CAPACITANCE (See Note 4) @8/20µs VC @ IPP @VWM ID µA @0V, 1 MHz Cj pF 21.0V @ 17.0A 21.0V @ 17.0A 29.2V @ 12.0A 29.2V @ 12.0A 34.6V @ 10.0A 34.6V @ 10.0A 58.3V @ 6.0A 58.3V @ 6.0A 20 20 1 1 1 1 1 1 150 150 80 80 50 50 40 40 Note 1: Part numbers with an additional “C” suffix are bidirectional devices, i.e., PSMS05C. Note 2: Unidirectional Only: Test between pin 1 to 2 or 5, 4 to 2 or 5, 6 to 2 or 5, 3 to 2 or 5. Note 3: Bidirectional Only: Test between pin 5 to 1 or 3 or 4 or 6. Electrical characteristics apply in both directions. Note 4: Unidirectional Only: Capacitance measured between pins 1, 3, 4, 6, to 2. 1,000 350W 8/20µs Waveform 100 10 0.1 05095.R3 9/03 FIGURE 2 PULSE WAVE FORM 120 IPP - Peak Pulse Current - % of IPP PPP - Peak Pulse Power - Watts 10,000 FIGURE 1 PEAK PULSE POWER VS PULSE TIME tf 100 TEST WAVEFORM PARAMETERS tf = 8µs td = 20µs Peak Value IPP 80 e-t 60 40 td = t I /2 PP 20 0 1 10 100 td - Pulse Duration - µs 1,000 10,000 2 0 5 10 15 t - Time - µs 20 25 30 www.protekdevices.com PSMS05 thru PSMS24C GRAPHS FIGURE 3 POWER DERATING CURVE 100 Peak Pulse Power 8/20µs % Of Rated Power 80 60 40 20 Average Power 0 0 25 50 75 100 125 TL - Lead Temperature - °C 150 FIGURE 4 OVERSHOOT & CLAMPING VOLTAGE FOR PSMS05C 5 Volts per Division 40 30 20 10 0 ESD Test Pulse: 25 kilovolt, 1/30ns (waveform) FIGURE 5 TYPICAL REVERSE VOLTAGE VS CAPACITANCE FOR PSMS05 160 C - Capacitance - pF 120 80 40 0 0 05095.R3 9/03 1 2 3 VR - Reverse Voltage - Volts 3 4 5 www.protekdevices.com PSMS05 thru PSMS24C APPLICATION NOTE The PSMS Series are TVS arrays designed to protect I/O or data lines from the damaging effects of ESD or EFT. This product series provides both unidirectional and bidirectional protection, with a surge capability of 350 Watts PPP per line for an 8/20µs waveform and ESD protection > 25 kilovolts. UNIDIRECTIONAL COMMON-MODE CONFIGURATION (Figure 1) The PSMS Series provides up to four (4) lines of protection in a common-mode configuration as depicted in Figure 1. Figure 1 - Unidirectional Configuration Common-Mode I/O Port Protection Circuit connectivity is as follows: ✔ Line 1 is connected to Pin 1. ✔ Line 2 is connected to Pin 3. ✔ Line 3 is connected to Pin 4. ✔ Line 4 is connected to Pin 6. ✔ Pin 5 is connected to ground. ✔ Pin 2 is not connected. LINE 1 LINE 2 3 2 1 4 5 6 The PSMSxxC Series provides up to four (4) lines of protection in a common-mode configuration as depicted in Figure 2. I/O PORT BIDIRECTIONAL COMMON-MODE CONFIGURATION (Figure 2) Circuit connectivity is as follows: ✔ Line 1 is connected to Pin 1. ✔ Line 2 is connected to Pin 3. ✔ Line 3 is connected to Pin 4. ✔ Line 4 is connected to Pin 5. ✔ Pin 6 is connected to ground. ✔ Pin 2 is not connected. LINE 3 LINE 4 CIRCUIT BOARD LAYOUT RECOMMENDATIONS Circuit board layout is critical for Electromagnetic Compatibility (EMC) protection. The following guidelines are recommended: Figure 2 - Bidirectional Configuration Common-Mode I/O Port Protection The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. LINE 1 LINE 2 ✔ The path length between the TVS device and the protected line should be minimized. ✔ All conductive loops including power and ground loops should be minimized. ✔ The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. ✔ Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. 3 2 1 4 5 6 I/O PORT ✔ LINE 3 LINE 4 05095.R3 9/03 4 www.protekdevices.com PSMS05 thru PSMS24C PACKAGE OUTLINE & DIMENSIONS PACKAGE OUTLINE SOT-23-6 D E 6 5 4 0º - 10º K PACKAGE DIMENSIONS J 1 2 3 DIM L J V B M F A G C A B C D E F G J K L M MILLIMETERS MIN MAX 2.80 1.50 0.90 0.35 0.85 1.70 0.90 0.090 2.60 0.20 TYP 0.35 INCHES MIN MAX 3.05 0.110 0.120 1.75 0.059 0.070 1.30 0.036 0.051 0.50 0.014 0.020 1.05 0.033 0.040 2.10 0.067 0.083 1.45 0.036 0.057 0.20 0.0035 0.008 3.00 0.102 0.118 0.20 TYP 0.007 TYP 0.007 TYP 0.55 0.014 0.022 NOTES MOUNTING PAD 1. Dimensioning and tolerances per ANSI Y14.5M, 1985. 2. Controlling Dimension: Inches 3. Dimensions are exclusive of mold flash and metal burrs. 0.094” (2.40mm) TAPE & REEL ORDERING NOMENCLATURE 1. Surface mount product is taped and reeled in accordance with EIA-481. 2. Suffix-T7 = 7 Inch Reel - 3,000 pieces per 8mm tape, i.e., PSMS05-T7. 3. Suffix-T13 = 13 Inch Reel - 10,000 pieces per 8mm tape, i.e., PSMS05-T13. 0.074” (1.90mm) 0.028” (0.70mm) 0.037” (0.95mm) 0.039” (1.00mm) Outline & Dimensions: Rev 1 - 11/01, 06013 COPYRIGHT © ProTek Devices 2003 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: [email protected] Web Site: www.protekdevices.com DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. 05095.R3 9/03 5 www.protekdevices.com