FREQUENCY QEN05 SMD 5x3.2 XO – Communications Equipment Application Specification (Rev-C) Electrical Characteristics ......................................................P01 Mechanical Characteristics ...................................................P02 Ordering Information .............................................................P03 Suggested Reflow Soldering profile ......................................P03 Tape Drawing........................................................................P04 Reel Drawing ........................................................................P04 Frequency QEN05 SMD 5x3.2 XO – Communications Equipment Application Specification (rev-C) December 15th, 2005 Electrical Characteristics Electrical Parameters Frequency range (see note 1) Output logic Operating temperature range (see table 1) Storage temperature range Power supply voltage (Vcc) Frequency Stability (see note 2) Aging (First Year) Input current (see table 2) Output load Duty cycle (see note 3) Rise & Fall time Start-up time Unit Minimum MHz 1.544 Typical Maximum Test conditions 125 HCMOS / TTL Output °C -10 to +70 -40 to +85 °C -55 +125 V +1.8 +5.0 ± ppm 25 50 100 ± ppm 5 Refer to Ordering Information Refer to Ordering Information Refer to Ordering Information Ref at 25°C mA pF 15 30 % 40/60 ns 7 ms 10 Refer to Ordering Information Refer to Ordering Information From 10% Vcc to 90% Vcc From 10% Vcc to 90% Vcc Note 1: Not all voltages, loads or stabilities are available for frequency over 70 MHz. Note 2: Include 25°C tolerance, operating temperature range, input voltage change, load change, first year aging, shock and vibration. Note 3: Duty cycle 45/55% is available on option. Table 1 : Stability Codes ± 25ppm ± 50ppm ± 100ppm -10 to +70°C C B A - 40 to +85°C G F D Table 2 : Input Current Frequency range (MHz) 1.544 to 9.999 10.00 to 34.999 35.00 to 49.999 50.00 to 125 Vcc=5V Cl=15 pF 15 mA 20 mA 35 mA 40 mA Vcc=3.3V Vcc=2.5V Vcc=1.8V Cl=15pF Cl=15pF Cl=15pF 8 mA 7 mA 6 mA 10 mA 8 mA 7 mA 25 mA 20 mA 15 mA 35 mA 30 mA 25 mA 1 TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost. Frequency QEN05 SMD 5x3.2 XO – Communications Equipment Application Specification (rev-C) December 15th, 2005 • Mechanical Characteristics SUGGESTED PAD Hmax = 1.3 mm TOP VIEW #1 #2 #3 #4 Line 1 Line 2 BOTTOM VIEW Tri state function Pin #1 Output (Pin #3) Open Active “1” Active “0” High Z Pin connections Tri state Ground Output +Vcc Marking Manufacturing code + 05 + stability/supply voltage/output code Frequency in MHz (6 digits) Example for QEN05BDA / 50MHz Line 1 : G05BDA Line 2 : 50.000 2 TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost. Frequency QEN05 SMD 5x3.2 XO – Communications Equipment Application December 15th, 2005 Specification (rev-C) Ordering Information QEN05 B Package type Temperature Stability SMD Package QEN05 : SMD 5x3.2 Part numbering system D A A : ± 100ppm vs -10 to +70°C B: C: D: F: G: ± 50ppm vs -10 to +70°C ± 25ppm vs -10 to +70°C ± 100ppm vs -40 to +85°C ± 50ppm vs -40 to +85°C ± 25ppm vs -40 to +85°C Supply Voltage A : + 5.0V D : +3.3V M : +2.5V N : +1.8V Output A : HCMOS 15pF B : HCMOS 30pF R 50.000MHZ Output Symmetry Option Nominal Frequency (MHz) Blank : 40/60% R : 45/55% Please enter the nominal frequency Suggested Reflow Soldering Profile 3 TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost. Frequency QEN05 SMD 5x3.2 XO – Communications Equipment Application December 15th, 2005 Specification (rev-C) Tape Drawing Item Code Dimension Tolerance Pitch of components P 8.0 ± 0.1 Pitch of sprocket hole Po 4.0 ± 0.1 Length from hole center to component center P1 2.0 ± 0.1 Width of carrier tape W 12.0 ± 0.3 Width of adhesive tape W0 5.5 ± 0.1 Height of component hole A 5.7 ± 0.1 Diameter of sprocket hole Do ∅ 1.5 ± 0.1 K 1.5 ± 0.1 Total of tape thickness Reel Drawing Multiple : 1Kpcs per Reel Unit : mm 4 TEMEX reserves the right to modify herein specifications and informations at any time when necessary to provide optimum performance and cost.