R1LV0408C-I Series Wide Temperature Range Version 4M SRAM (512-kword × 8-bit) REJ03C0098-0200Z Rev. 2.00 May.25.2004 Description The R1LV0408C-I is a 4-Mbit static RAM organized 512-kword × 8-bit. R1LV0408C-I Series has realized higher density, higher performance and low power consumption by employing CMOS process technology (6-transistor memory cell). The R1LV0408C-I Series offers low power standby power dissipation; therefore, it is suitable for battery backup systems. It has packaged in 32-pin SOP, 32-pin TSOP II and 32-pin STSOP. Features • Single 3 V supply: 2.7 V to 3.6 V • Access time: 55/70 ns (max) • Power dissipation: Active: 6 mW/MHz (typ) Standby: 1.5 µW (typ) • Completely static memory. No clock or timing strobe required • Equal access and cycle times • Common data input and output. Three state output • Directly TTL compatible. All inputs and outputs • Battery backup operation. • Operating temperature: −40 to +85°C Rev.2.00, May.25.2004, page 1 of 12 R1LV0408C-I Series Ordering Information Type No. Access time Package R1LV0408CSP-5SI 55 ns 525-mil 32-pin plastic SOP (32P2M-A) R1LV0408CSP-7LI 70 ns R1LV0408CSB-5SI 55 ns R1LV0408CSB-7LI 70 ns R1LV0408CSA-5SI 55 ns R1LV0408CSA-7LI 70 ns Rev.2.00, May.25.2004, page 2 of 12 400-mil 32-pin plastic TSOP II (32P3Y-H) 8mm × 13.4mm STSOP (32P3K-B) R1LV0408C-I Series Pin Arrangement 32-pin SOP 32-pin TSOP A18 A16 A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 32-pin STSOP VCC A15 A17 WE# A13 A8 A9 A11 OE# A10 CS# I/O7 I/O6 I/O5 I/O4 I/O3 (Top view) Pin Description Pin name Function A0 to A18 Address input I/O0 to I/O7 Data input/output CS# (CS) Chip select OE# (OE) Output enable WE# (WE) Write enable VCC Power supply VSS Ground Rev.2.00, May.25.2004, page 3 of 12 A11 A9 A8 A13 WE# A18 A15 VCC A17 A16 A14 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 (Top view) OE# A10 CS# I/O7 I/O6 I/O5 I/O4 I/O3 VSS I/O2 I/O1 I/O0 A0 A1 A2 A3 R1LV0408C-I Series Block Diagram LSB MSB V CC A11 A9 A8 A15 A18 A10 A13 A17 A16 A14 A12 V SS Row Decoder I/O0 • • • • • Memory Matrix 2,048 × 2,048 • • Column I/O Input Data Control Column Decoder I/O7 LSB A3 A2A1A0 A4 A5 A6 A7 MSB •• CS# WE# Timing Pulse Generator Read/Write Control OE# Rev.2.00, May.25.2004, page 4 of 12 • • R1LV0408C-I Series Operation Table WE# CS# OE# Mode VCC current I/O0 to I/O7 Ref. cycle × H × Not selected ISB, ISB1 High-Z H L H Output disable ICC High-Z H L L Read ICC Dout Read cycle L L H Write ICC Din Write cycle (1) L L L Write ICC Din Write cycle (2) Note: H: VIH, L: VIL, ×: VIH or VIL Absolute Maximum Ratings Parameter Symbol Value Power supply voltage relative to VSS VCC −0.5 to +4.6 Unit V 1 2 Terminal voltage on any pin relative to VSS VT −0.5* to VCC + 0.5* Power dissipation PT 0.7 W Operating temperature Topr −40 to +85 °C Storage temperature range Tstg −65 to +150 °C Storage temperature range under bias Tbias −40 to +85 °C V Notes: 1. VT min: −3.0 V for pulse half-width ≤ 30 ns. 2. Maximum voltage is +4.6 V. DC Operating Conditions (Ta = −40 to +85°C) Parameter Symbol Min Typ Max Unit Supply voltage VCC 2.7 3.0 3.6 V VSS 0 0 0 V VIH 2.2 VCC + 0.3 V 0.6 V Input high voltage Input low voltage Note: VIL −0.3* 1. VIL min: −3.0 V for pulse half-width ≤ 30 ns. Rev.2.00, May.25.2004, page 5 of 12 1 R1LV0408C-I Series DC Characteristics Parameter Symbol Min Typ Max Unit Test conditions Input leakage current |ILI| Output leakage current |ILO| 1 µA Vin = VSS to VCC 1 µA CS# = VIH or OE# = VIH or WE# = VIL or VI/O = VSS to VCC Operating current ICC 5*1 10 mA CS# = VIL, Others = VIH/ VIL, II/O = 0 mA Average operating current ICC1 8*1 25 mA Min. cycle, duty = 100%, CS# = VIL, Others = VIH/VIL II/O = 0 mA ICC2 2*1 5 mA Cycle time = 1 µs, duty = 100%, II/O = 0 mA, CS# ≤ 0.2 V, VIH ≥ VCC − 0.2 V, VIL ≤ 0.2 V ISB 0.1*1 0.3 mA CS# = VIH to +85°C ISB1 10 µA Vin ≥ 0 V, CS# ≥ VCC − 0.2 V to +70°C ISB1 Standby current Standby current −5SI to +40°C −7LI ISB1 8 µA 0.7* 2 3 µA 1 3 µA 20 µA 16 µA 10 µA to +25°C ISB1 0.5* to +85°C ISB1 to +70°C ISB1 to +40°C ISB1 to +25°C Output low voltage Output high voltage 0.7* 2 1 ISB1 0.5* 10 µA VOL 0.4 V IOL = 2.1 mA VOL2 0.2 V IOL = 100 µA VOH 2.4 V IOH = −1.0 mA VOH2 VCC − 0.2 V IOH = −0.1 mA Notes: 1. Typical values are at VCC = 3.0 V, Ta = +25°C and specified loading, and not guaranteed. 2. Typical values are at VCC = 3.0 V, Ta = +40°C and specified loading, and not guaranteed. Capacitance (Ta = +25°C, f = 1.0 MHz) Parameter Symbol Min Typ Max Unit Test conditions Note Input capacitance Cin 8 pF Vin = 0 V 1 Input/output capacitance CI/O 10 pF VI/O = 0 V 1 Note: 1. This parameter is sampled and not 100% tested. Rev.2.00, May.25.2004, page 6 of 12 R1LV0408C-I Series AC Characteristics (Ta = −40 to +85°C, VCC = 2.7 V to 3.6 V, unless otherwise noted.) Test Conditions • • • • Input pulse levels: VIL = 0.4 V, VIH = 2.4 V Input rise and fall time: 5 ns Input and output timing reference levels: 1.5 V Output load: 1 TTL Gate + CL (50 pF) (R1LV0408C-5SI) 1 TTL Gate + CL (100 pF) (R1LV0408C-7LI) (Including scope and jig) Read Cycle R1LV0408C-I -5SI -7LI Parameter Symbol Min Max Min Max Unit Read cycle time tRC 55 70 ns Address access time tAA 55 70 ns Chip select access time tCO 55 70 ns Output enable to output valid tOE 30 35 ns Chip select to output in low-Z tLZ 10 10 ns 2 Output enable to output in low-Z tOLZ 5 5 ns 2 Chip deselect to output in high-Z tHZ 0 20 0 25 ns 1, 2 Output disable to output in high-Z tOHZ 0 20 0 25 ns 1, 2 Output hold from address change tOH 10 10 ns Rev.2.00, May.25.2004, page 7 of 12 Notes R1LV0408C-I Series Write Cycle R1LV0408C-I -5SI -7LI Parameter Symbol Min Max Min Max Unit Notes Write cycle time tWC 55 70 ns Chip selection to end of write tCW 50 60 ns 4 Address setup time tAS 0 0 ns 5 Address valid to end of write tAW 50 60 ns Write pulse width tWP 40 50 ns 3, 12 Write recovery time tWR 0 0 ns 6 Write to output in high-Z tWHZ 0 20 0 25 ns 1, 2, 7 Data to write time overlap tDW 25 30 ns Data hold from write time tDH 0 0 ns Output active from end of write tOW 5 5 ns 2 Output disable to output in high-Z tOHZ 0 20 0 25 ns 1, 2, 7 Notes: 1. tHZ, tOHZ and tWHZ are defined as the time at which the outputs achieve the open circuit conditions and are not referred to output voltage levels. 2. This parameter is sampled and not 100% tested. 3. A write occurs during the overlap (tWP) of a low CS# and a low WE#. A write begins at the later transition of CS# going low or WE# going low. A write ends at the earlier transition of CS# going high or WE# going high. tWP is measured from the beginning of write to the end of write. 4. tCW is measured from CS# going low to the end of write. 5. tAS is measured from the address valid to the beginning of write. 6. tWR is measured from the earlier of WE# or CS# going high to the end of write cycle. 7. During this period, I/O pins are in the output state so that the input signals of the opposite phase to the outputs must not be applied. 8. If the CS# low transition occurs simultaneously with the WE# low transition or after the WE# transition, the output remain in a high impedance state. 9. Dout is the same phase of the write data of this write cycle. 10. Dout is the read data of next address. 11. If CS# is low during this period, I/O pins are in the output state. Therefore, the input signals of the opposite phase to the outputs must not be applied to them. 12. In the write cycle with OE# low fixed, tWP must satisfy the following equation to avoid a problem of data bus contention. tWP ≥ tDW min + tWHZ max Rev.2.00, May.25.2004, page 8 of 12 R1LV0408C-I Series Timing Waveform Read Timing Waveform (WE# = VIH) tRC Address Valid address tAA tCO CS# tLZ tHZ tOE tOLZ OE# tOHZ Dout High impedance Valid data tOH Rev.2.00, May.25.2004, page 9 of 12 R1LV0408C-I Series Write Timing Waveform (1) (OE# Clock) tWC Address Valid address tAW tWR OE# tCW CS# *8 tWP tAS WE# tOHZ Dout High impedance tDW Din Rev.2.00, May.25.2004, page 10 of 12 Valid data tDH R1LV0408C-I Series Write Timing Waveform (2) (OE# Low Fixed) tWC Address Valid address tCW tWR CS# *8 tAW tWP WE# tOH tAS tOW tWHZ *9 Dout High impedance tDW tDH *11 Din Rev.2.00, May.25.2004, page 11 of 12 Valid data *10 R1LV0408C-I Series Low VCC Data Retention Characteristics (Ta = −40 to +85°C) Max Unit Test conditions*3 Parameter Symbol Min Typ VCC for data retention VDR 2.0 V CS# ≥ VCC − 0.2 V, Vin ≥ 0 V to +85°C ICCDR 10 µA VCC = 3.0 V, Vin ≥ 0 V to +70°C ICCDR CS# ≥ VCC − 0.2 V Data retention current −5SI to +40°C −7LI ICCDR 8 µA 0.7* 2 3 µA 1 3 µA to +25°C ICCDR 0.5* to +85°C ICCDR 20 µA to +70°C ICCDR 16 µA to +40°C ICCDR 0.7*2 10 µA ICCDR 1 10 µA tCDR 0 ns tRC* ns to +25°C Chip deselect to data retention time Operation recovery time tR 0.5* 4 See retention waveform Notes: 1. Typical values are at VCC = 3.0 V, Ta = +25°C and specified loading, and not guaranteed. 2. Typical values are at VCC = 3.0 V, Ta = +40°C and specified loading, and not guaranteed. 3. CS# controls address buffer, WE# buffer, OE# buffer, and Din buffer. In data retention mode, Vin levels (address, WE#, OE#, I/O) can be in the high impedance state. 4. tRC = read cycle time. Low VCC Data Retention Timing Waveform (CS# Controlled) tCDR Data retention mode VCC 2.7 V 2.2 V VDR CS# 0V Rev.2.00, May.25.2004, page 12 of 12 CS# ≥ VCC – 0.2 V tR Revision History Rev. Date R1LV0408C-I Series Data Sheet Contents of Modification Page Description 1.00 Jul.24.2003 Initial issue 2.00 May.25.2004 1 Features Standby: 2.4 µW (typ) to 1.5 µW (typ) 5 Absolute Maximum Ratings Notes 2 : +7.0 V to +4.6 V 6 DC characteristics −5SI and −7LI items’ description are divided. 12 Low VCC Data Retention Characteristics −5SI and −7LI items’ description are divided. 12 Low VCC Data Retention Timing Waveform 4.5 V to 2.7 V 2.4 V to 2.2 V Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500 Fax: <1> (408) 382-7501 Renesas Technology Europe Limited. Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, United Kingdom Tel: <44> (1628) 585 100, Fax: <44> (1628) 585 900 Renesas Technology Europe GmbH Dornacher Str. 3, D-85622 Feldkirchen, Germany Tel: <49> (89) 380 70 0, Fax: <49> (89) 929 30 11 Renesas Technology Hong Kong Ltd. 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2375-6836 Renesas Technology Taiwan Co., Ltd. FL 10, #99, Fu-Hsing N. Rd., Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. 26/F., Ruijin Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1, Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 © 2004. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .1.0