VISHAY RCG04021K00JNED

RCG e3
www.vishay.com
Vishay Draloric
Fully RoHS Compliant, Green, Thick Film,
Rectangular Chip Resistors
FEATURES
• Green resistor - does not use RoHS exemptions
• Stability R/R = 1 % for 1000 h at 70 ° C
• 2 mm pitch packaging option for 0603 size
• Metal glaze on high quality ceramic
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
CASE
SIZE
INCH
CASE
SIZE
METRIC
POWER RATING
P70
W
LIMITING
ELEMENT
VOLTAGE
Umax.
ACRMS/DC
V
TEMPERATURE
COEFFICIENT
± ppm/K
TOLERANCE
±%
100
RCG0402
0402
RR 1005M
0.063
50
RESISTANCE
RANGE

1R0 to 9R76
150R to 10M
1
150
SERIES
E24; E96
10R to 147R
200
5
1R0 to 10M
E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. = 1.5 A
RCG0603
0603
0.1
RR 1608M
75
100
1
200
5
1R0 to 10M
E24; E96
E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. = 2.0 A
RCG0805
0805
RR 2012M
0.125
150
100
1
200
5
1R0 to 10M
E24; E96
E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. = 2.5 A
RCG1206
1206
0.25
RR 3216M
200
100
1
200
5
1R0 to 10M
E24; E96
E24
Zero-Ohm-Resistor: Rmax. = 20 m, Imax. = 3.5 A
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
• Marking: See datasheet “Surface Mount Resistor Marking” (document number 20020).
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
RCG0402
RCG0603
RCG0805
RCG1206
W
0.063
0.1
0.125
0.25
Operating voltage Umax. ACRMS/DC
V
50
75
150
200
Insulation voltage Uins (1 min)
V
75
100
200
300
Insulation resistance

> 109
Operating temperature range
°C
- 55 to + 155
Weight
mg
5.5
10
Rated dissipation P70
(1)
0.65
2
Note
(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
Revision: 13-Feb-13
Document Number: 20047
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCG e3
www.vishay.com
Vishay Draloric
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: RCG080510K0FKEA
R
C
G
0
8
0
5
1
0
K
0
F
K
E
MODEL
VALUE
TOLERANCE
TCR
PACKAGING
RCG0402
RCG0603
RCG0805
RCG1206
R = Decimal
K = Thousand
M = Million
0000 = 0  Jumper
F = ± 1.0 %
J = ± 5.0 %
Z = Jumper
K = ± 100 ppm/K
L = ± 150 ppm/K
N = ± 200 ppm/K
0 = Jumper
EA, EB,
EC, ED,
EE, EI,
EL
100
10K
1%
EA
MODEL
TCR
RESISTANCE
TOLERANCE
PACKAGING
RCG0402
RCG0603
RCG0805
RCG1206
± 100 ppm/K
± 150 ppm/K
± 200 ppm/K
10R = 10 
10K = 10 k
1M = 1 M
0R0 = Jumper
±1%
±5%
EA, EB,
EC, ED,
EE, EI,
EL
A
PRODUCT DESCRIPTION: RCG0805 100 10K 1 % EA
RCG0805
PACKAGING
MODEL
CODE
QUANTITY
CARRIER TAPE
WIDTH
PITCH
ED
10 000
Paper tape acc.
to IEC 60068-3
Type I
8 mm
2 mm
RCG0402
RCG0603
RCG0805
RCG1206
Revision: 13-Feb-13
EE
50 000
EI
5000
ED
10 000
EL
20 000
EE
50 000
EA
5000
EB
10 000
EC
20 000
EA
5000
EB
10 000
EC
20 000
EA
5000
EB
10 000
EC
20 000
REEL DIAMETER
180 mm/7"
330 mm/13"
180 mm/7"
Paper tape acc.
to IEC 60068-3
Type I
180 mm/7"
8 mm
2 mm
285 mm/11.25"
330 mm/13"
180 mm/7"
Paper tape acc.
to IEC 60068-3
Type I
8 mm
4 mm
285 mm/11.25"
330 mm/13"
180 mm/7"
Paper tape acc.
to IEC 60068-3
Type I
8 mm
4 mm
285 mm/11.25"
330 mm/13"
180 mm/7"
Paper tape acc.
to IEC 60068-3
Type I
8 mm
4 mm
285 mm/11.25"
330 mm/13"
Document Number: 20047
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCG e3
www.vishay.com
Vishay Draloric
DIMENSIONS in millimeters
SIZE
SOLDER PAD DIMENSIONS
DIMENSIONS
INCH METRIC
L
W
REFLOW SOLDERING
H
T1
T2
a
b
l
WAVE SOLDERING
a
b
l
1.0
0.9
0.9
1.0
1.3
1.2
0.9
1.3
1.3
1.7
2.0
1.1
1.7
2.3
0402
1005
1.0 ± 0.05
0.5 ± 0.05
0.35 ± 0.05 0.25 ± 0.05
0.2 ± 0.1
0.4
0.6
0.5
0603
1608
1.55
+ 0.10
- 0.05
0.85 ± 0.1
0.45 ± 0.05
0.3 ± 0.2
0.3 ± 0.2
0.5
0.9
0805
2012
2.0
+ 0.20
- 0.10
1.25 ± 0.15
0.45 ± 0.05
0.3
+ 0.20
- 0.10
0.3 ± 0.2
0.7
1206
3216
3.2
+ 0.10
- 0.20
1.6 ± 0.15
0.55 ± 0.05
0.45 ± 0.2
0.4 ± 0.2
0.9
- 50
0
50
Fraction of Rated Dissipation P70
FUNCTIONAL PERFORMANCE
100
%
50
0
Derating
°C
100
150
70
Ambient Temperature in amb
GREEN REQUIREMENTS
SUBSTANCES
CONCENTRATION LIMIT
Lead (Pb)
< 1000 ppm
Mercury (Hg)
< 1000 ppm
Cadmium (Cd)
< 100 ppm
Hexavalent Chronium
< 1000 ppm
Polybrominated Biphenyl (PBB)
< 1000 ppm
Polybrominated Diphenyl Ether (PBDE)
< 1000 ppm
Bromine (Br)
< 900 ppm
Chlorine (Cl)
Sum of Bromine and Chlorine
< 900 ppm
 1500 ppm max.
Antimony (Sb)
< 900 ppm
Red Phosphorous
< 100 ppm
Notes
• No exemptions (e.g. Pb in glass) may be applied to any substances or application for the “Green” category
• All concentration levels are based on homogenous materials
Revision: 13-Feb-13
Document Number: 20047
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCG e3
www.vishay.com
Vishay Draloric
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
TEST
REQUIREMENTS
PERMISSIBLE CHANGE (R)
PROCEDURE
Stability for product types:
RCG e3
4.5
-
Resistance
-
4.7
-
Voltage proof
U = 1.4 x Uins; 60 s
4.13
-
Short time overload
U = 2.5 x P 70 x R  2 x Umax.;
Duration acc. to style
STABILITY CLASS 2 OR BETTER
1 to 10 M
1 to 10 M
±1%
±5%
No flashover or breakdown
± (0.25 % R + 0.05 )
± (0.5 % R + 0.05 )
4.17.2
58 (Td)
Solderability
Solder bath method;
Sn96.5Ag3Cu0.5
non-activated flux;
(245 ± 5) °C
(3 ± 0.3) s
4.8.4.2
-
Temperature
coefficient
(20/- 55/20) °C and
(20/125/20) °C
4.32
21 (Uu3)
Shear
(adhesion)
RR 1608 and smaller: 9 N
RR 2012 and larger: 45 N
No visible damage
4.33
21 (Uu1)
Substrate bending
Depth 2 mm;
3 times
No visible damage, no open circuit in bent position
± (0.25 % R + 0.05 )
4.23
-
Climatic sequence:
-
4.23.2
2 (Ba)
Dry heat
125 °C; 16 h
4.23.3
30 (Db)
Damp heat, cyclic
55 °C;  90 % RH;
24 h; 1 cycle
4.23.4
1 (Aa)
Cold
- 55 °C; 2 h
4.23.5
13 (M)
Low air pressure
1 kPa; (25 ± 10) °C; 1 h
4.23.6
30 (Db)
Damp heat, cyclic
55 °C;  90 % RH;
24 h; 5 cycles
4.23.7
-
DC load
4.25.1
-
Endurance at 70 °C
Good tinning ( 95 % covered)
no visible damage
± 100 ppm/K, ± 150 ppm/K
± 200 ppm/K
± (1 % R + 0.05 )
± (2 % R + 0.1 )
70 °C; 1000 h
± (1 % R + 0.05 )
± (2 % R + 0.1 )
± (0.25 % R + 0.05 )
± (0.5 % R + 0.05 )
U=
P 70 x R
U = P 70 x R  Umax.;
1.5 h on; 0.5 h off;
58 (Td)
Resistance to
soldering heat
Solder bath method
(260 ± 5) °C;
(10 ± 1) s
4.35
-
Flamability,
needle flame test
IEC 60695-11-5;
10 s
No burning after 30 s
4.24
78 (Cab)
Damp heat,
steady state
(40 ± 2) °C;
(93 ± 3) % RH;
56 days
± (1 % R + 0.05 )
4.25.3
-
Endurance at
upper category
temperature
155 °C, 1000 h
4.40
-
Electrostatic
discharge
(human body model)
IEC 61340-3-1;
3 pos. + 3 neg. discharges;
ESD test voltage acc. to size
4.18.2
Revision: 13-Feb-13
± (1 % R + 0.05 )
± (2 % R + 0.1 )
± (1 % R + 0.05 )
Document Number: 20047
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
RCG e3
www.vishay.com
Vishay Draloric
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2
TEST
METHOD
TEST
REQUIREMENTS
PERMISSIBLE CHANGE (R)
PROCEDURE
Stability for product types:
RCG e3
STABILITY CLASS 2 OR BETTER
1 to 10 M
1 to 10 M
4.29
45 (XA)
Component solvent
resistance
Isopropyl alcohol;
50 °C; method 2
No visible damage
4.30
45 (XA)
Solvent resistance
of marking
Isopropyl alcohol;
50 °C; method 1,
toothbrush
Marking legible,
no visible damage
4.22
6 (Fc)
Vibration, endurance
by sweeping
f = 10 Hz to 2000 Hz;
x, y, z  1.5 mm;
A  200 m/s2;
10 sweeps per axis
4.37
-
Periodic electric
overload
4.27
-
Single pulse high
voltage overload,
10 μs/700 μs
15 x P 70 x R
 2 x Umax.;
0.1 s on; 2.5 s off;
1000 cycles
± (0.25 % R + 0.05 )
± (0.5 % R + 0.05 )
U=
Û = 10 x P 70 x R
 2 x Umax.;
10 pulses
± (1 % R + 0.05 )
± (1 % R + 0.05 )
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2, environmental test procedures
Packaging of components is done in paper tapes according to IEC 60286-3.
Revision: 13-Feb-13
Document Number: 20047
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Vishay:
RCG06030000Z0EA RCG060310R0FKEA RCG0603100RFKEA RCG06031K00FKEA RCG060310K0FKEA
RCG0603100KFKEA RCG06031M00FKEA RCG08050000Z0EA RCG080510R0FKEA RCG0805100RFKEA
RCG08051K00FKEA RCG080510K0FKEA RCG0805100KFKEA RCG08051M00FKEA RCG12060000Z0EA
RCG120610R0FKEA RCG1206100RFKEA RCG12061K00FKEA RCG120610K0FKEA RCG1206100KFKEA
RCG12061M00FKEA RCG040210K0JNED RCG04020000Z0ED RCG04021K00FKED RCG04021K00JNED
RCG04021K50FKED RCG04021M00FKED RCG04021M00JNED RCG04022K00FKED RCG040210K0FKED
RCG04022K20JNED RCG040210R0JNED RCG0402100KFKED RCG0402100KJNED RCG040215K0FKED
RCG0402100RJNED RCG04021R00JNED RCG040233K0JNED RCG04022R20JNED RCG12061K50FKEA
RCG0805100RJNEA RCG0805499RFKEA RCG0402220RJNED RCG08057K50JNEA RCG080575K0JNEA
RCG0805470RJNEA RCG12061K00JNEA RCG0805470KJNEA RCG12061M00JNEA RCG12061R00FKEA
RCG12061R00JNEA RCG120610K0JNEA RCG0805220RJNEA RCG080515K0FKEA RCG08052K00FKEA
RCG08052K20JNEA RCG08052R20JNEA RCG080520K0FKEA RCG080522K0JNEA RCG040220K0FKED
RCG0805220KJNEA RCG1206100KJNEA RCG08053K30JNEA RCG080533K0JNEA RCG08054K70JNEA
RCG08054K99FKEA RCG08054R70JNEA RCG080547K0JNEA RCG080547R0JNEA RCG080522R0JNEA
RCG1206470KJNEA RCG1206470RJNEA RCG120649K9FKEA RCG1206499RFKEA RCG12067K50JNEA
RCG120675K0JNEA RCG120610R0JNEA RCG12064R70JNEA RCG120622R0JNEA RCG080549K9FKEA
RCG1206100RJNEA RCG120615K0FKEA RCG12062K00FKEA RCG12062K20JNEA RCG12062R20JNEA
RCG120647R0JNEA RCG120622K0JNEA RCG120647K0JNEA RCG1206220KJNEA RCG1206220RJNEA
RCG12063K30JNEA RCG120633K0JNEA RCG12064K70JNEA RCG12064K99FKEA RCG120620K0FKEA
RCG060310R0JNEA RCG06031K50FKEA RCG06031M00JNEA RCG06031R00FKEA RCG06031R00JNEA