Photoelectrics Amplifier, µ-Processor Controlled Type S1430 UAP, 3 Inputs/3 Transistor Outputs • µ-Processor controlled • Amplifier unit for 3 sets of photoelectrics • 3 independent outputs • NPN/PNP both NO or NC selectable • Self-diagnostic functions • Alignment failure indication • Multivoltage 12 to 30 VAC/DC • Modulated and synchronized light • Adjustable sensitivity for each channel • LED indications: supply, outputs, signal quality • 11-pin plug-in housing • For 115 or 230 VAC use power supplys from SS120-series Product Description µ-Processor controlled amplifier for 3 sets of photoelectric sensors, type MOFTR, MKFTR, MIFTR or MHFTR. Utilising an 11-pin circular plug for easy connection, outputs freely selectable for NPN/PNP or NO/NC. Self- Ordering Key diagnostics for system test. Protected against short-circuits, reverse wiring or cross talk from adjacent photoelectrics. Multi-voltage power supply. Sensitivity is individually adjustable for each set of photoelectrics. S14 30 UAP 912 Type Special function Output type Power supply Type Selection Plug type Ordering no. Supply: 12 - 30 VAC/DC Circular, 11 pins S 1430 UAP 912 Specifications Rated operational voltage (UB) pins 2 & 10 DC AC Rated operational power AC supply DC supply Power ON delay (tv) Output function Output current Continuous (Ie) Short-time (I) Min. load current (Im) OFF-state current (Ir) Voltage drop (Ud) Protection, outputs Supply to photoelectric switch Emitter Supply voltage (open loop) Current Output resistance 10.8 to 33 VDC 10.8 to 33 VAC, 45 to 65 Hz 4 VA 3W < 300 ms NPN and PNP switching Make and break function DIP-Switch selectable 100 mA per output 100 mA max. 0.5 mA Max. 100 µA ≤ 3.5 VDC Reverse polarity, short-circuit, transients Tx1: Pin 1 Tx2: Pin 9 Tx3: Pin 6 Shield: Pin 11 (common) 7 V square wave ≤ 300 mA short-circuit protected 10 Ω Specifications are subject to change without notice (25.06.99) Supply to photoelectric switch (cont.) Receiver Rx1: Pin 4 Rx2: Pin 7 Rx3: Pin 8 Shield: Pin 5 (common) Supply voltage (open loop) 5 VDC Short-circuit current 10 mA Input resistance 470 Ω Sensitivity • 2 ranges, DIP-Switch selectable (% of Sn) - low sensitivity (25%) - high sensitivity (100%) • Sensitivity adjustment with 270°: Turn knob on CH 1, 2, 3 Note: • Maximum range indicated on photoelectric switch data sheet in high sensitivity range only • Operation within low sensitivity range, increases ambient light and crosstalk immunity Operating frequency (f) Light/dark ratio 1:1 16 Hz 1 S 1430 UAP Specifications (cont.) Response time OFF-ON (tON) ON-OFF (tOFF) Indication Supply ON Output ON Signal quality Environment Overvoltage category Degree of protection Pollution degree Temperature Operating Storage Weight Approvals CE-marking Truth Table Make switching 20 ms 20 ms Object present LED, green LED, yellow LED, red Dirt on lenses, misaligned or sensitivity too low III (IEC 60664) IP 20 (IEC 60529, 60947-1) 3 (IEC 60664/60664A, 60947-1) Output LED yellow OFF -20° to +50°C (-4° to +122°F) -50° to +85°C (-58° to 185°F) 150 g CSA Yes Level LED red Yes No No Yes No No -- No Yes1) -- No Yes1) ON ON OFF ON ON ON or flashing OFF OFF ON or flashing ON ON OFF OFF OFF OFF Output NPN/PNP OFF 1) Break switching ON Under normal operating conditions, the red level indication LED has to be OFF. The level indication LED will turn on shortly each time an object enters or exits the sensing zone, even if the photoelectric switch is correctly installed and adjusted. Procedure for Test Functions (Dip-Switch Selection) Transmitter test (switch 5 in the up position) When switch 5 is placed in the up position all yellow and red LED’s on the front of the unit will flash simultaneously. Once the test is completed (approx. 3 scans) and a wiring fault is detected, such as reverse polarity or shortcircuit, the transmitter that has the fault condition will be indicated by the red LED being continuously ON. If a fault condition is not existing then only the yellow LED will be ON. If a fault exists, correct the fault condition and then repeat the test, this will ensure proper wiring has been done. Always reset switch 5 for normal operation of system when testing completed. Receiver test (switch 6 in the up position) When switch 6 is placed in the up position all yellow and red LED’s on the front of the unit will flash simultaneously. Once the test is completed (approx. 3 scans) and a wiring fault is detected, such as reverse polarity or shortcircuit, the receiver that has the fault condition will be indicated by the red LED being continuously ON. If a fault condition is not existing then only the yellow LED will be ON. If a fault exists, correct the fault condition and then repeat the test, this will ensure proper wiring has been done. Always reset switch 6 for normal operation of system when testing completed. Function test (switch 5 and 6 in the up position) When switch 5 and 6 are both placed in the up position (simultaneously) the yellow and red LED’s on the front of the housing will begin to flash simultaneously and then the LED’s will cycle from channel 1 to channel 2 and then to channel 3. Once the complete system scan is done the indication of the system condition will be displayed (see below). System test will continue until switch 5 and 6 are reset. LED Indication Yellow LED ON ! Red LED OFF } System Test OK ! Yellow LED ON Red LED ON } Tx’s and Rx’s mismatched, e.g. Rx3 seeing Tx1 ! Yellow LED OFF Red LED ON } Alignment error or beam obstructed by object Operation Diagram Signal strength Time Power supply Object present Signal quality Break switching ! Make switching 2 Specifications are subject to change without notice (25.06.99) S 1430 UAP Dimensions DIP-Switch (located behind cover): 35 80 1: PNP/NPN CH 1 output SW 1 2 3 4 5 6 2: PNP/NPN CH 2 output 3: PNP/NPN CH 3 output 4: Low sensitivity (25%) / high sensitivity (100%) 5: Test button, transmitters are transmitting, no short, wired correctly 6: Test button, receivers are receiving, no short, wired correctly 5+6 together: System test (transmitter and receiver) sw 1, 2, 3: sw 4: PNP make/NPN break Range 25% NPN make/PNP break Range 100%, normal operation 84 sw 6: sw 5: Transmitter test Receiver test Normal operation Normal operation sw 5+6: System test 4 75 5 Normal operation Wiring Diagrams Rx 1 Tx 1 Rx 2 Tx 2 Rx 3 1 Rx Tx 31 6 5 7 4 8 3 9 2 10 1 11 Power Supply ON sockets 1: Transmitter 1 2: Supply (+ VDC) 3: No connection 4: Receiver 1 5: GND (Receivers) 6: Transmitter 3 7: Receiver 2 8: Receiver 3 9: Transmitter 2 10: Supply (- VDC) 11: GND (Transmitters) Accessories - 11 pole circular socket Socket cover for S111 Socket cover for S411 Holding down spring Mounting rack Front panel mounting bezel Connection cable (2 plugs) 2 x 6/6 modular plugs - Power supply for 115/230 VAC - DIN-rail interface Wire colour coding white black red green yellow blue PNP NPN B C D A B C D 10-40 VDC F F + - 10-40 VDC + - Interface S111, S111A, S411, ZPD11 BB1 BB4 HF SM13 FRS2 2.0 m, 6 wires two plugs SS120-series 6IODC Delivery Contents • Output connection cable • Output connection cable • Amplifier • DIN-rail interface • Screw driver • Packaging: Output A: + (10-40 VDC) B: Output 1 (max. 100 mA) C: Output 2 (max. 100 mA) D: Output 3 (max. 100 mA) E: For handheld tester F: - DC 1 m, 6 wires one plug 0.2 m, 6 wires two plugs S 1430 UAP 912 6IODC 6IODC DIN-rail interface (DIN EN 50 035, EN 50 022) output from plug to screw terminals Cardboard box Specifications are subject to change without notice (25.06.99) 3