SPANSION S29GL032M10BFIR43

S29GL-M MirrorBitTM Flash Family
S29GL256M, S29GL128M, S29GL064M, S29GL032M
256 Megabit, 128 Megabit, 64 Megabit, and 32 Megabit,
3.0 Volt-only Page Mode Flash Memory featuring
0.23 µm MirrorBit Process Technology
Data Sheet
This product family has been retired and is not recommended for designs. For new and current designs, S29GL032A, S29GL064A, S29GL128N, and S29GL256N supersede S29GL032M,
S29GL064M, S29GL128M, and S29GL256M respectively. These are the factory-recommended migration paths. Please refer to the S29GL-A and S29GL-N Datasheets for specifications
and ordering information. Availability of this document is retained for reference and historical purposes only.
Notice to Readers: This document states the current technical specifications
regarding the Spansion product(s) described herein. Spansion Inc. deems the
products to have been in sufficient production volume such that subsequent
versions of this document are not expected to change. However, typographical
or specification corrections, or modifications to the valid combinations offered
may occur.
Publication Number S29GL-M_00
Revision B
Amendment 6
Issue Date October 10, 2006
D a t a
S h e e t
Notice On Data Sheet Designations
Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise
readers of product information or intended specifications throughout the product life cycle, including development, qualification, initial production, and full production. In all cases, however,
readers are encouraged to verify that they have the latest information before finalizing their design. The following descriptions of Spansion data sheet designations are presented here to highlight their presence and definitions.
Advance Information
The Advance Information designation indicates that Spansion Inc. is developing one or more
specific products, but has not committed any design to production. Information presented in a
document with this designation is likely to change, and in some cases, development on the product may discontinue. Spansion Inc. therefore places the following conditions upon Advance Information content:
“This document contains information on one or more products under development at Spansion Inc. The
information is intended to help you evaluate this product. Do not design in this product without contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed
product without notice.”
Preliminary
The Preliminary designation indicates that the product development has progressed such that a
commitment to production has taken place. This designation covers several aspects of the product life cycle, including product qualification, initial production, and the subsequent phases in the
manufacturing process that occur before full production is achieved. Changes to the technical
specifications presented in a Preliminary document should be expected while keeping these aspects of production under consideration. Spansion places the following conditions upon Preliminary content:
“This document states the current technical specifications regarding the Spansion product(s) described
herein. The Preliminary status of this document indicates that product qualification has been completed,
and that initial production has begun. Due to the phases of the manufacturing process that require
maintaining efficiency and quality, this document may be revised by subsequent versions or modifications due to changes in technical specifications.”
Combination
Some data sheets will contain a combination of products with different designations (Advance Information, Preliminary, or Full Production). This type of document will distinguish these products
and their designations wherever necessary, typically on the first page, the ordering information
page, and pages with DC Characteristics table and AC Erase and Program table (in the table
notes). The disclaimer on the first page refers the reader to the notice on this page.
Full Production (No Designation on Document)
When a product has been in production for a period of time such that no changes or only nominal
changes are expected, the Preliminary designation is removed from the data sheet. Nominal
changes may include those affecting the number of ordering part numbers available, such as the
addition or deletion of a speed option, temperature range, package type, or VIO range. Changes
may also include those needed to clarify a description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following conditions to documents in this category:
“This document states the current technical specifications regarding the Spansion product(s) described
herein. Spansion Inc. deems the products to have been in sufficient production volume such that subsequent versions of this document are not expected to change. However, typographical or specification
corrections, or modifications to the valid combinations offered may occur.”
Questions regarding these document designations may be directed to your local sales office.
ii
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
S29GL-M MirrorBitTM Flash Family
S29GL256M, S29GL128M, S29GL064M, S29GL032M
256 Megabit, 128 Megabit, 64 Megabit, and 32 Megabit,
3.0 Volt-only Page Mode Flash Memory featuring
0.23 µm MirrorBit Process Technology
Data Sheet
This product family has been retired and is not recommended for designs. For new and current designs, S29GL032A, S29GL064A, S29GL128N,
and S29GL256N supersede S29GL032M, S29GL064M, S29GL128M, and S29GL256M respectively. These are the factory-recommended migration
paths. Please refer to the S29GL-A and S29GL-N Datasheets for specifications and ordering information. Availability of this document is retained
for reference and historical purposes only.
Distinctive Characteristics
Architectural Advantages
„
Single power supply operation
— 3 volt read, erase, and program operations
„
Manufactured on 0.23 µm MirrorBit process
technology
„
Secured Silicon Sector region
— 128-word/256-byte sector for permanent, secure
identification through an 8-word/16-byte random
Electronic Serial Number, accessible through a
command sequence
— May be programmed and locked at the factory or by
the customer
„
„
„
Flexible sector architecture
— 256 Mb: 512 32-Kword (64 Kbyte) sectors
— 128 Mb: 256 32-Kword (64 Kbyte) sectors
— 64 Mb (uniform sector models): 128 32-Kword
(64-Kbyte) sectors or 128 32 Kword sectors
„
— 32 Mb (uniform sector models): 64 32-Kword
(64-Kbyte) sectors of 64 32-Kword sectors
— 32 Mb (boot sector models): 63 32-Kword (64 Kbyte)
sectors + 8 4-Kword (8-Kbyte) boot sectors
Compatibility with JEDEC standards
— Provides pinout and software compatibility for singlepower supply flash, and superior inadvertent write
protection
„
100,000 erase cycles typical per sector
„
20-year data retention typical
Performance Characteristics
„
High performance
— 90 ns access time (128 Mb, 64 Mb, 32 Mb),
100 ns access time (256 Mb)
— 4-word/8-byte page read buffer
— 25 ns page read times (128 Mb, 64 Mb, 32 Mb)
— 30 ns page read times (256 Mb)
— 16-word/32-byte write buffer
Publication Number S29GL-M_00
Revision B
Package options
— 40-pin TSOP
— 48-pin TSOP
— 56-pin TSOP
— 64-ball Fortified BGA
— 48-ball fine-pitch BGA
— 63-ball fine-pitch BGA
Software & Hardware Features
— 64 Mb (boot sector models): 127 32-Kword
(64-Kbyte) sectors + 8 4Kword (8Kbyte) boot sectors
„
— 16-word/32-byte write buffer reduces overall
programming time for multiple-word updates
Low power consumption (typical values at 3.0 V,
5 MHz)
— 18 mA typical active read current (64 Mb, 32 Mb)
— 25 mA typical active read current (256 Mb, 128 Mb)
— 50 mA typical erase/program current
— 1 µA typical standby mode current
Software features
— Program Suspend & Resume: read other sectors
before programming operation is completed
— Erase Suspend & Resume: read/program other
sectors before an erase operation is completed
— Data# polling & toggle bits provide status
— CFI (Common Flash Interface) compliant: allows host
system to identify and accommodate multiple flash
devices
— Unlock Bypass Program command reduces overall
multiple-word programming time
„
Hardware features
— Sector Group Protection: hardware-level method of
preventing write operations within a sector group
— Temporary Sector Unprotect: VID-level method of
charging code in locked sectors
— WP#/ACC input accelerates programming time
(when high voltage is applied) for greater throughput
during system production. Protects first or last sector
regardless of sector protection settings on uniform
sector models
— Hardware reset input (RESET#) resets device
— Ready/Busy# output (RY/BY#) detects program or
erase cycle completion
Amendment 6
Issue Date October 10, 2006
D a t a
S h e e t
General Description
The S29GL256/128/064/032M family of devices are 3.0 V single power Flash memory manufactured using 0.23 µm MirrorBit technology. The S29GL256M is a 256†Mbit, organized as 16,777,216
words or 33,554,432 bytes. The S29GL128M is a 128 Mbit, organized as 8,388,608 words or
16,777,216 bytes. The S29GL064M is a 64 Mbit, organized as 4,194,304 words or 8,388,608 bytes.
The S29GL032M is a 32 Mbit, organized as 2,097,152 words or 4,194,304 bytes. Depending on the
model number, the devices have an 8-bit wide data bus only, 16-bit wide data bus only, or a 16-bit
wide data bus that can also function as an 8-bit wide data bus by using the BYTE# input. The devices
can be programmed either in the host system or in standard EPROM programmers.
Access times as fast as 90 ns (S29GL128M, S29GL064M, S29GL032M) or 100 ns (S29GL256M) are
available. Note that each access time has a specific operating voltage range (VCC) as specified in
Product Selector Guide and the Ordering Information sections starting on page 16. Package offerings include 40-pin TSOP, 48-pin TSOP, 56-pin TSOP, 48-ball fine-pitch BGA, 63-ball fine-pitch BGA
and 64-ball Fortified BGA, depending on model number. Each device has separate chip enable
(CE#), write enable (WE#) and output enable (OE#) controls.
Each device requires only a single 3.0 volt power supply for both read and write functions. In
addition to a VCC input, a high-voltage accelerated program (ACC) feature provides shorter programming times through increased current on the WP#/ACC input. This feature is intended to
facilitate factory throughput during system production, but may also be used in the field if desired.
The device is entirely command set compatible with the JEDEC single-power-supply Flash standard. Commands are written to the device using standard microprocessor write timing. Write cycles
also internally latch addresses and data needed for the programming and erase operations.
The sector erase architecture allows memory sectors to be erased and reprogrammed without
affecting the data contents of other sectors. The device is fully erased when shipped from the
factory.
Device programming and erasure are initiated through command sequences. Once a program or
erase operation starts, the host system need only poll the DQ7 (Data# Polling) or DQ6 (toggle) status bits or monitor the Ready/Busy# (RY/BY#) output to determine whether the operation is
complete. To facilitate programming, an Unlock Bypass mode reduces command sequence overhead by requiring only two write cycles to program data instead of four.
Hardware data protection measures include a low VCC detector that automatically inhibits write
operations during power transitions. The hardware sector protection feature disables both program
and erase operations in any combination of sectors of memory. This can be achieved in-system or
via programming equipment.
The Erase Suspend/Erase Resume feature allows the host system to pause an erase operation
in a given sector to read or program any other sector and then complete the erase operation. The
Program Suspend/Program Resume feature enables the host system to pause a program operation in a given sector to read any other sector and then complete the program operation.
The hardware RESET# pin terminates any operation in progress and resets the device, after
which it is then ready for a new operation. The RESET# pin may be tied to the system reset circuitry.
A system reset would thus also reset the device, enabling the host system to read boot-up firmware
from the Flash memory device.
The device reduces power consumption in the standby mode when it detects specific voltage levels
on CE# and RESET#, or when addresses are stable for a specified period of time.
The Write Protect (WP#) feature protects the first or last sector by asserting a logic low on the
WP#/ACC pin or WP# pin, depending on model number. The protected sector is still protected even
during accelerated programming.
The Secured Silicon Sector provides a 128-word/256-byte area for code or data that can be permanently protected. Once this sector is protected, no further changes within the sector can occur.
Spansion MirrorBit flash technology combines years of Flash memory manufacturing experience to
produce the highest levels of quality, reliability and cost effectiveness. The device electrically erases
all bits within a sector simultaneously via hot-hole assisted erase. The data is programmed using
hot electron injection.
2
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Table of Contents
Distinctive Characteristics . . . . . . . . . . . . . . . . . . . . 1
General Description . . . . . . . . . . . . . . . . . . . . . . . . 2
Product Selector Guide . . . . . . . . . . . . . . . . . . . . . .5
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connection Diagrams . . . . . . . . . . . . . . . . . . . . . . .6
For S29GL064M (model R0) only ....................................................................7
For S29GL064M (model R0) only .................................................................. 10
For S29GL032M (model R0) only .................................................................. 12
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Logic Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
S29GL064M (Models R1, R2, R8, R9) ............................................................ 14
S29GL064M (Models R3, R4) .......................................................................... 14
S29GL064M (Model R5) .....................................................................................15
S29GL064M (Model R6, R7) .............................................................................15
S29GL128M .............................................................................................................15
Ordering Information: S29GL032M . . . . . . . . . . . . 16
S29GL032M Standard Products ...................................................................... 16
Table 1. S29GL032M Ordering Options ................................. 17
Ordering Information: S29GL064M . . . . . . . . . . . 18
S29GL064M Standard Products ...................................................................... 18
Table 2. S29GL064M Ordering Options ................................. 19
Ordering Information: S29GL128M . . . . . . . . . . . .20
Unprotection Address Table ................................................. 49
Table 23. S29GL064M (Models R1, R2, R8, R9) Sector Group
Protection/Unprotection Addresses ....................................... 49
Table 24. S29GL064M (Model R3) Sector Group Protection/
Unprotection Address Table ................................................. 50
Table 26. S29GL064M (Model R5) Sector Group Protection/
Unprotection Addresses ...................................................... 51
Table 27. S29GL064M (Models R6, R7) Sector Group Protection/
Unprotection Address ......................................................... 51
Table 28. S29GL128M Sector Group Protection/Unprotection
Addresses ......................................................................... 51
Table 29. S29GL256M Sector Group Protection/Unprotection
Addresses ......................................................................... 52
Temporary Sector Group Unprotect .......................................................... 53
Figure 1. Temporary Sector Group Unprotect Operation.......... 53
Figure 2. In-System Sector Group Protect/Sector Group Unprotect
Algorithms........................................................................ 54
Secured Silicon Sector Flash Memory Region ........................................... 55
Write Protect (WP#) ....................................................................................... 56
Hardware Data Protection ............................................................................. 56
Low VCC Write Inhibit ................................................................................ 56
Write Pulse “Glitch” Protection ............................................................... 56
Logical Inhibit ................................................................................................... 56
Power-Up Write Inhibit ............................................................................... 56
Table 3. S29GL128M Ordering Options ................................. 20
Common Flash Memory Interface (CFI) . . . . . . . 57
Ordering Information: S29GL256M . . . . . . . . . . . . 21
Table 30. CFI Query Identification String .............................. 57
Table 31. System Interface String ........................................ 57
Table 32. Device Geometry Definition ................................... 58
Table 33. Primary Vendor-Specific Extended Query ................ 59
Table 4. S29GL256M Ordering Options ................................. 21
Device Bus Operations . . . . . . . . . . . . . . . . . . . . . . 22
Table 5. Device Bus Operations ........................................... 22
Word/Byte Configuration ............................................................................... 22
Requirements for Reading Array Data ........................................................ 22
Page Mode Read ..................................................................................................23
Writing Commands/Command Sequences .................................................23
Write Buffer .....................................................................................................23
Accelerated Program Operation ...............................................................23
Autoselect Functions .....................................................................................23
Standby Mode ...................................................................................................... 24
Automatic Sleep Mode ..................................................................................... 24
RESET#: Hardware Reset Pin ........................................................................ 24
Output Disable Mode ....................................................................................... 24
Table 6. S29GL032M (Model R0) Sector Addresses ................ 25
Table 7. S29GL032M (Models R1, R2) Sector Addresses ......... 26
Table 8. S29GL032M (Model R3)
Top Boot Sector Addresses ................................................. 27
Table 9. S29GL032M (Model R4)
Bottom Boot Sector Addresses ............................................ 28
Table 11. S29GL064M (Models R1, R2, R8, R9)
Sector Addresses .............................................................. 30
Table 14. S29GL064M (Model R5, R6, R7) Sector Addresses ... 37
Table 16. S29GL256M Sector Address Table ......................... 41
Autoselect Mode .................................................................................................47
Table 17. Autoselect Codes, (High Voltage Method) ............... 47
Table 18. S29GL032M (Model R0) Sector Group Protection/
Unprotection Addresses ...................................................... 48
Table 19. S29GL032M (Models R1, R2) Sector Group Protection/
Unprotection Addresses ...................................................... 48
Table 20. S29GL032M (Model R3) Sector Group Protection/
Unprotection Address Table ................................................ 48
Table 21. S29GL032M (Model R4) Sector Group Protection/
Unprotection Address Table ................................................ 49
Table 22. S29GL064M (Model 00) Sector Group Protection/
October 10, 2006 S29GL-M_00_B6
Command Definitions . . . . . . . . . . . . . . . . . . . . . . 60
Reading Array Data ...........................................................................................60
Reset Command .................................................................................................60
Autoselect Command Sequence .....................................................................61
Enter/Exit Secured Silicon Sector Command Sequence ..........................61
Word Program Command Sequence .......................................................61
Unlock Bypass Command Sequence ........................................................ 62
Write Buffer Programming .......................................................................... 62
Accelerated Program .................................................................................... 63
Figure 3. Write Buffer Programming Operation ...................... 64
Figure 4. Program Operation ............................................... 65
Program Suspend/Program Resume Command Sequence .................... 65
Figure 5. Program Suspend/Program Resume........................ 66
Chip Erase Command Sequence ...................................................................66
Sector Erase Command Sequence ................................................................66
Figure 6. Erase Operation ................................................... 67
Erase Suspend/Erase Resume Commands ..................................................68
Command Definitions .......................................................................................69
Table 34. Command Definitions( x16 Mode, BYTE# = VIH) ...... 69
Table 35. Command Definitions (x8 Mode, BYTE# = VIL) ........ 70
Write Operation Status .................................................................................... 71
DQ7: Data# Polling ............................................................................................. 71
Figure 7. Data# Polling Algorithm ........................................ 72
RY/BY#: Ready/Busy# ....................................................................................... 72
DQ6: Toggle Bit I ............................................................................................... 72
Figure 8. Toggle Bit Algorithm ............................................. 74
DQ2: Toggle Bit II .............................................................................................. 74
DQ5: Exceeded Timing Limits ........................................................................ 75
DQ3: Sector Erase Timer ................................................................................ 75
DQ1: Write-to-Buffer Abort ........................................................................... 75
Table 36. Write Operation Status ......................................... 76
S29GL-M MirrorBitTM Flash Family
3
D a t a
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . 77
Figure 9. Maximum Negative Overshoot Waveform ................. 77
Figure 10. Maximum Positive Overshoot Waveform................. 77
DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .78
CMOS Compatible ............................................................................................ 78
Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Figure 11. Test Setup ......................................................... 79
Table 37. Test Specifications ............................................... 79
Key to Switching Waveforms . . . . . . . . . . . . . . . .79
Figure 12. Input Waveforms and Measurement Levels............. 79
AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . .80
Read-Only Operations—S29GL256M Only ...............................................80
Read-Only Operations—S29GL128M only ................................................ 80
Read-Only Operations—S29GL064M Only ............................................... 81
Read-Only Operations—S29GL032M only ................................................ 82
Alternate CE# Controlled Erase and Program Operations—
S29GL256M .......................................................................................................... 93
Alternate CE# Controlled Erase and Program Operations—
S29GL128M ...........................................................................................................94
Alternate CE# Controlled Erase and Program Operations—
S29GL064M .......................................................................................................... 95
Alternate CE# Controlled Erase and Program Operations—
S29GL032M ..........................................................................................................96
Figure 24. Alternate CE# Controlled Write (Erase/
Program) Operation Timings ............................................... 97
Erase and Programming Performance . . . . . . . . . 98
TSOP Pin and BGA Package Capacitance . . . . . .98
Physical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 99
Figure 16. Program Operation Timings .................................. 89
Figure 17. Accelerated Program Timing Diagram .................... 89
Figure 18. Chip/Sector Erase Operation Timings ..................... 90
Figure 19. Data# Polling Timings
(During Embedded Algorithms) ............................................ 90
Figure 20. Toggle Bit Timings (During Embedded Algorithms) .. 91
Figure 21. DQ2 vs. DQ6 ...................................................... 91
TS040—40-Pin Standard Thin Small Outline Package (TSOP) ............99
TSR040—40-Pin Standard and Reverse Thin Small Outline Package
(TSOP) ................................................................................................................. 100
TS048—48-Pin Standard and Reverse Thin Small Outline Package
(TSOP) ...................................................................................................................101
TSR048—48-Pin Standard and Reverse Thin Small Outline Package
(TSOP) ..................................................................................................................102
TS056/TSR056—56-Pin Standard and Reverse Thin Small Outline Package (TSOP) ..........................................................................................................103
LAA064—64-Ball Fortified Ball Grid Array (FBGA) ..............................104
LAC064—64-Pin 18 x 12 mm Package .........................................................105
FBA048—48-Pin 6.15 x 8.15 mm Package ...................................................106
FBC048—48-Pin 8 x 9 mm Package ............................................................107
FBE063—63-Pin 12 x 11 mm Package ........................................................... 108
FPT-48P-M19 ...................................................................................................... 109
FPT-56P-M01 ....................................................................................................... 109
Temporary Sector Unprotect ......................................................................... 91
Revision Summary . . . . . . . . . . . . . . . . . . . . . . . . 110
Figure 13. Read Operation Timings ....................................... 82
Figure 14. Page Read Timings .............................................. 83
Hardware Reset (RESET#) ...............................................................................83
Figure 15. Reset Timings..................................................... 84
Erase and Program Operations—S29GL256M Only ............................... 85
Erase and Program Operations—S29GL128M Only ............................... 86
Erase and Program Operations—S29GL064M Only .............................. 87
Erase and Program Operations—S29GL032M Only .............................. 88
Figure 22. Temporary Sector Group Unprotect Timing Diagram 92
Figure 23. Sector Group Protect and Unprotect Timing Diagram 92
4
S h e e t
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Product Selector Guide
Part Number
S29GL256M
Speed Option
S29GL128M
S29GL064M
S29GL032M
10
11
90
10
90
10
11
90
10
11
Max. Access Time (ns)
100
110
90
100
90
100
110
90
100
110
Max. CE# Access Time (ns)
100
110
90
100
90
100
110
90
100
110
Max. Page Access Time (ns)
30
30
25
30
25
30
30
25
30
30
Max. OE# Access Time (ns)
30
30
25
30
25
30
30
25
30
30
Block Diagram
VCC
DQ15–DQ0 (A-1)
RY/BY#
Sector Switches
VSS
Erase Voltage
Generator
RESET#
WE#
WP#/ACC
BYTE#
Input/Output
Buffers
State
Control
Command
Register
PGM Voltage
Generator
Chip Enable
Output Enable
Logic
CE#
OE#
VCC Detector
AMax**–A0
Timer
Address Latch
STB
STB
Data
Latch
Y-Decoder
Y-Gating
X-Decoder
Cell Matrix
** AMax: GL256M = A23, GL128M = A22, GL064M = A21 (GL064M-00 = A22), GL032M = A20 (GL032M-00 = A21)
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
5
D a t a
S h e e t
Connection Diagrams
A16
A15
A14
A13
A12
A11
A9
A8
WE#
RESET#
ACC
RY/BY#
A18
A7
A6
A5
A4
A3
A2
A1
A15
A14
A13
A12
A11
A10
A9
A8
A192
A20
WE#
RESET#
A211,2
WP#/ACC2
RY/BY#2
A18
A17
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
40-Pin Standard TSOP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48-Pin Standard TSOP
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A17
VSS
A20
A19
A10
DQ7
DQ6
DQ5
DQ4
VCC
VIO
A21
DQ3
DQ2
DQ1
DQ0
OE#
VSS
CE#
A0
A16
BYTE#2
VSS
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
Notes:
1. Pin 13 is NC on S29GL032M.
2. Pin 9 is A21, Pin 13 is ACC, Pin 14 is WP#, Pin 15 is A19, and Pin 47 is VIO on S29GL064M (models R6, R7).
6
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
For S29GL064M (model R0) only
NC
A22
A16
A15
A14
A13
A12
A11
A9
A8
WE#
RESET#
ACC
RY/BY#
A18
A7
A6
A5
A4
A3
A2
A1
NC
NC
A231
A222
A15
A14
A13
A12
A11
A10
A9
A8
A19
A20
WE#
RESET#
A213
WP#/ACC
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
48-Pin Standard TSOP
56-Pin Standard TSOP
NC
NC
A17
VSS
A20
A19
A10
DQ7
DQ6
DQ5
DQ4
VCC
VIO
A21
DQ3
DQ2
DQ1
DQ0
OE#
VSS
CE#
A0
NC
NC
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
NC
NC
A16
BYTE#
VSS
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
NC
VIO
Notes:
1. Pin 1 is NC on S29GL128M, 29GL064M, and S29GL032M.
2. Pin 2 is NC on S29GL064M, and S29GL032M.
3. Pin 15 is NC on S29GL032M.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
7
D a t a
S h e e t
64-ball Fortified BGA
Top View, Balls Facing Down
A8
B8
C8
D8
E8
F8
G8
H8
NC
A222
A233
VIO4
VSS
NC
NC
NC
A7
B7
C7
D7
E7
F7
G7
H7
A13
A12
A14
A15
A16
BYTE#
DQ15/A-1
VSS
A6
B6
C6
D6
E6
F6
G6
H6
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
A5
B5
C5
D5
E5
F5
G5
H5
WE#
RESET#
A211
A19
DQ5
DQ12
VCC
DQ4
A4
B4
C4
D4
E4
F4
G4
H4
A18
A20
DQ2
DQ10
DQ11
DQ3
RY/BY# WP#/ACC
A3
B3
C3
D3
E3
F3
G3
H3
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
A2
B2
C2
D2
E2
F2
G2
H2
A3
A4
A2
A1
A0
CE#
OE#
VSS
A1
B1
C1
D1
E1
F1
G1
H1
NC
VIO4
NC
NC
NC
Notes:
1. Ball
2. Ball
3. Ball
4. Ball
5. Ball
8
5
NC
NC
NC
C5 is NC on S29GL032M.
B8 is NC on S29GL064M and S29GL032M.
C8 is NC on S29GL128M, S29GL064M and S29GL032M.
D8 and Ball F1 are NC on S29GL064M (models R3, R4) and S29GL032M (models R3, R4, R5, R6).
F7 is NC on S29GL064M (model R5).
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
63-Ball Fine-Pitch BGA
Top View, Balls Facing Down
A8
B8
L8
M8
NC*
NC*
NC*
NC*
A7
B7
NC*
NC*
C7
E7
D7
A14
F7
A15
G7
A16
H7
1
BYTE#
J7
K7
L7
M7
DQ15/A-1
VSS
NC*
NC*
A13
A12
C6
D6
E6
F6
G6
H6
J6
K6
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
C5
D5
E5
F5
G5
H5
J5
K5
WE#
RESET#
A21
A19
DQ5
DQ12
VCC
DQ4
C4
D4
RY/BY# WP#/ACC
E4
F4
G4
H4
J4
K4
A18
A20
DQ2
DQ10
DQ11
DQ3
C3
D3
E3
F3
G3
H3
J3
K3
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
A2
C2
D2
E2
F2
G2
H2
J2
K2
L2
M2
NC*
A3
A4
A2
A1
A0
CE#
OE#
VSS
NC*
NC*
L1
M1
NC*
NC*
A1
B1
* Balls are shorted together via the substrate but not connected to the die.
NC*
NC*
Note: Ball H7 is VIO on S29GL064M (model R5).
Special Package Handling Instructions
Special handling is required for Flash Memory products in molded packages (TSOP and BGA). The
package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
9
D a t a
S h e e t
For S29GL064M (model R0) only
63-Ball Fine-Pitch BGA
Top View, Balls Facing Down
L8
M8
NC*
NC*
K7
L7
M7
VSS
NC*
NC*
K2
L2
M2
VSS
NC*
NC*
L1
M1
NC*
NC*
A8
B8
NC*
NC*
A7
B7
C7
D7
E7
F7
G7
H7
J7
NC*
A14
A13
A15
A16
A17
NC
A20
C6
D6
E6
F6
G6
H6
J6
K6
A9
A8
A11
A12
A19
A10
DQ6
DQ7
C5
D5
E5
F5
G5
H5
J5
K5
WE#
RESET#
A22
NC
DQ5
NC
VCC
DQ4
C4
D4
E4
F4
G4
H4
J4
K4
RY/BY#
ACC
NC
NC
DQ2
DQ3
VIO
A21
C3
D3
E3
F3
G3
H3
J3
K3
A7
A18
A6
A5
DQ0
NC
NC
DQ1
A2
C2
D2
E2
F2
G2
H2
J2
NC*
A3
A4
A2
A1
A0
CE#
OE#
NC*
A1
NC*
B1
NC*
* Balls are shorted together via the substrate but not connected to the die.
Special Package Handling Instructions
Special handling is required for Flash Memory products in molded packages (TSOP and BGA). The
package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time.
10
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
48-ball Fine-pitch BGA
Top View, Balls Facing Down
A6
B6
C6
E6
F6
G6
BYTE# DQ15/A-1
H6
VSS
A13
A12
A14
A15
A16
A5
B5
C5
D5
E5
F5
G5
H5
A9
A8
A10
A11
DQ7
DQ14
DQ13
DQ6
A4
B4
C4
D4
E4
F4
G4
H4
WE#
RESET#
NC
A19
DQ5
DQ12
VCC
DQ4
A3
B3
RY/BY# WP#/ACC
October 10, 2006 S29GL-M_00_B6
D6
C3
D3
E3
F3
G3
H3
A18
A20
DQ2
DQ10
DQ11
DQ3
A2
B2
C2
D2
E2
F2
G2
H2
A7
A17
A6
A5
DQ0
DQ8
DQ9
DQ1
A1
B1
C1
D1
E1
F1
G1
H1
A3
A4
A2
A1
A0
CE#
OE#
VSS
S29GL-M MirrorBitTM Flash Family
11
D a t a
S h e e t
For S29GL032M (model R0) only
48-Ball Fine-Pitch BGA
Top View, Balls Facing Down
A6
B6
C6
D6
E6
F6
G6
H6
A14
A13
A15
A16
A17
NC
A20
VSS
A5
B5
C5
D5
E5
F5
G5
H5
A9
A8
A11
A12
A19
A10
D6
D7
A4
B4
C4
D4
E4
F4
G4
H4
WE#
RESET#
NC
NC
D5
NC
VCC
D4
A3
B3
C3
D3
E3
F3
G3
H3
RY/BY#
ACC
NC
NC
D2
D3
VIO
A21
A2
B2
C2
D2
E2
F2
G2
H2
A7
A18
A6
A5
D0
NC
NC
D1
A1
B1
C1
D1
E1
F1
G1
H1
A3
A4
A2
A1
A0
CE#
OE#
VSS
Special Package Handling Instructions
Special handling is required for Flash Memory products in moulded packages (TSOP and BGA).
The package and/or data integrity may be compromised if the package body is exposed to temperatures above 150°C for prolonged periods of time.
12
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Pin Description
A23–A0
A22–A0
A21–A0
A20–A0
DQ7–DQ0
DQ14–DQ0
DQ15/A-1
=
=
=
=
=
=
=
CE#
OE#
WE#
WP#/ACC
=
=
=
=
ACC
WP#
RESET#
RY/BY#
BYTE#
VCC
=
=
=
=
=
=
VSS
NC
VIO
=
=
=
October 10, 2006 S29GL-M_00_B6
24 Address inputs
23 Address inputs
22 Address inputs
21 Address inputs
8 Data inputs/outputs
15 Data inputs/outputs
DQ15 (Data input/output, word mode), A-1 (LSB
Address input, byte mode)
Chip Enable input
Output Enable input
Write Enable input
Hardware Write Protect input/Programming
Acceleration input
Acceleration input
Hardware Write Protect input
Hardware Reset Pin input
Ready/Busy output
Selects 8-bit or 16-bit mode
3.0 volt-only single power supply
(see Product Selector Guide for speed options and
voltage supply tolerances)
Device Ground
Pin Not Connected Internally
Output Buffer Power
S29GL-M MirrorBitTM Flash Family
13
D a t a
S h e e t
Logic Symbols
S29GL032M (Model R0)
S29GL032M (Models R1, R2)
22
21
A21–A0
CE#
A20–A0
8
DQ7–DQ0
CE#
OE#
OE#
WE#
WE#
ACC
WP#/ACC
RESET#
RESET#
VIO
BYTE#
RY/BY#
16 or 8
DQ15–DQ0
(A-1)
RY/BY#
VIO
S29GL032M (Models R3, R4)
S29GL064M (Model R0)
21
23
A20–A0
CE#
A22–A0
16 or 8
DQ15–DQ0
(A-1)
CE#
OE#
OE#
WE#
WE#
WP#/ACC
ACC
RESET#
RESET#
VIO
RY/BY#
8
DQ7–DQ0
RY/BY#
BYTE#
S29GL064M (Models R1, R2, R8, R9)
22
S29GL064M (Models R3, R4)
22
A21–A0
CE#
16 or 8
DQ15–DQ0
(A-1)
A21–A0
CE#
OE#
OE#
WE#
WE#
WP#/ACC
WP#/ACC
RESET#
RESET#
BYTE#
BYTE#
RY/BY#
16 or 8
DQ15–DQ0
(A-1)
RY/BY#
VIO
14
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Logic Symbols
S29GL064M (Model R5)
S29GL064M (Model R6, R7)
22
22
A21–A0
CE#
A21–A0
16
DQ15–DQ0
CE#
OE#
OE#
WE#
WE#
ACC
WP#
RESET#
ACC
VIO
16
DQ15–DQ0
RESET#
RY/BY#
VIO
S29GL128M
S29GL256M
23
24
A22–A0
CE#
16 or 8
DQ15–DQ0
(A-1)
CE#
OE#
DQ15–DQ0
(A-1)
WE#
WP#/ACC
WP#/ACC
RESET#
RESET#
RY/BY#
BYTE#
VIO
October 10, 2006 S29GL-M_00_B6
16 or 8
OE#
WE#
BYTE#
A23–A0
RY/BY#
VIO
S29GL-M MirrorBitTM Flash Family
15
D a t a
S h e e t
Ordering Information: S29GL032M
This product has been retired and is not recommended for designs. For new and current designs, S29GL032A supersedes S29GL032M, and is the
factory-recommended migration path. Please refer to the S29GL-A Datasheet for specifications and ordering information.
S29GL032M Standard Products
Standard products are available in several packages and operating ranges. The order number (Valid Combination)
is formed by a combination of the following:
S29GL032M
10
T
A
I
R1
0
PACKING TYPE
0
2
3
= Tray
= 7” Tape and Reel
= 13” Tape and Reel
MODEL NUMBER
R0
R1
R2
R3
R4
= x8, VCC=3.0-3.6V, Uniform sector device
= x8/x16, VCC=3.0-3.6V, Uniform sector device, highest address sector
protected when WP#/ACC=VIL
= x8/x16, VCC=3.0-3.6V, Uniform sector device, lowest address sector
protected when WP#/ACC=VIL
= x8/x16, VCC=3.0-3.6V, Top boot sector device, top two address sectors
protected when WP#/ACC=VIL
= x8/x16, VCC=3.0-3.6V, Bottom boot sector device, bottom two
address sectors protected when WP#/ACC=VIL
TEMPERATURE RANGE
I
C
= Industrial (–40°C to +85°C)
= Commercial (0°C to +70°C)
PACKAGE MATERIAL SET
A
F
B
C
=
=
=
=
Standard
Pb-Free
Standard
Pb-Free
PACKAGE TYPE
T
B
F
= Thin Small Outline Package (TSOP) Standard Pinout
= Fine-pitch Ball-Grid Array Package
= Fortified Ball-Grid Array Package
SPEED OPTION
See Product Selector Guide and Valid Combinations
DEVICE NUMBER/DESCRIPTION
S29GL032M
32 Megabit Page-Mode Flash Memory Manufactured using 0.23 µm MirrorBit™
Process Technology, 3.0 Volt-only Read, Program, and Erase
16
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
Table 1.
S h e e t
S29GL032M Ordering Options
S29GL032M Valid Combinations
Device
Number
Speed
Option
Package, Material,
& Temperature Range
TAC,TFC
BAC,BFC
TAC,TFC
90
FAC,FFC
Model
Number
Packing
Type
R0
R1,R2
TAC,TFC
BAC,BFC
R3,R4
FAC,FFC
S29GL032M
TAI,TFI
BAI,BFI
TAI,TFI
90, 10, 11
FAI,FFI
R0
0,2,3
(Note 1)
R1,R2
TAI,TFI
BAI,BFI
FAI,FFI
R3,R4
TBI,TCI
Package Description
(Notes)
TS040 (2, 3, 5)
TSOP
FBC048 (4)
Fine-Pitch BGA
TS056 (2, 3, 5)
TSOP
LAA064 (4)
Fortified BGA
TS048 (2, 3, 5)
TSOP
FBC048 (4)
Fine-Pitch BGA
LAA064 (4)
Fortified BGA
TS040 (2, 3, 5)
TSOP
FBC048 (4)
Fine-Pitch BGA
TS056 (2, 3, 5)
TSOP
LAA064 (4)
Fortified BGA
TS048 (2, 3, 5)
TSOP
FBC048 (4)
Fine-Pitch BGA
LAA064 (4)
Fortified BGA
FPT-48P-M19 (3, 6)
TSOP
Notes:
1. Type 0 is standard. Specify others as required: TSOPs can be packed in Types 0 and 3; BGAs can be packed in Types 0, 2, or 3.
2. This package is recommended for new designs using TSOPs.
3. TSOP package marking omits packing type designator from the ordering part number.
4. BGA package marking omits leading “S29” and packing type designator from the ordering part number.
5. 100% Matte Sn is used for Pb-free TSOP plating.
6. SnBi is used for Pb-free TSOP plating.
Valid Combinations
Valid Combinations list configurations planned to be supported in volume for this device. Consult your local sales office to
confirm availability of specific valid combinations and to check on newly released combinations.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
17
D a t a
S h e e t
Ordering Information: S29GL064M
This product has been retired and is not recommended for designs. For new and current designs, S29GL064A supersedes S29GL064M, and is the
factory-recommended migration path. Please refer to the S29GL-A Datasheet for specifications and ordering information.
S29GL064M Standard Products
Standard products are available in several packages and operating ranges. The order number (Valid Combination)
is formed by a combination of the following:
S29GL064M
90
T
A
I
R1
0
PACKING TYPE
0
2
3
= Tray
= 7” Tape and Reel
= 13” Tape and Reel
MODEL NUMBER
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
= x8, VCC=3.0-3.6V, Uniform sector device
= x8/x16, VCC=3.0-3.6V, Uniform sector device, highest address
sector protected when WP#/ACC=VIL
= x8/x16, VCC=3.0-3.6V, Uniform sector device, lowest address sector
protected when WP#/ACC=VIL
= x8/x16, VCC=3.0-3.6V, Top boot sector device, top two address
sectors protected when WP#/ACC=VIL
= x8/x16, VCC=3.0-3.6V, Bottom boot sector device, bottom two
address sectors protected when WP#/ACC=VIL
= x16, VCC=3.0-3.6V, Uniform sector device
= x16, VCC=3.0-3.6V, Uniform sector device, highest address sector
protected when WP#=VIL
= x16, VCC=3.0-3.6V, Uniform sector device, lowest address sector
protected when WP#=VIL
= x8/x16, VCC=3.0-3.6V, Uniform sector device, highest address
sector protected when WP#/ACC=VIL, FPT-56P-M01 package only
= x8/x16, VCC=3.0-3.6V, Uniform sector device, lowest address sector
protected when WP#/ACC=VIL, FPT-56P-M01 package only
TEMPERATURE RANGE
I
= Industrial (–40°C to +85°C)
PACKAGE MATERIAL SET
A
F
B
C
D
=
=
=
=
=
Standard
Pb-Free
Standard
Pb-Free
Pb-Free
PACKAGE TYPE
T
B
F
= Thin Small Outline Package (TSOP) Standard Pinout
= Fine-pitch Ball-Grid Array Package
= Fortified Ball-Grid Array Package
SPEED OPTION
See Product Selector Guide and Valid Combinations
DEVICE NUMBER/DESCRIPTION
S29GL064M
64 Megabit Page-Mode Flash Memory Manufactured using 0.23 um MirrorBitTM
Process Technology, 3.0 Volt-only Read, Program, and Erase
18
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
Table 2.
S h e e t
S29GL064M Ordering Options
S29GL064M Valid Combinations
Device
Number
Speed
Option
Package, Material, &
Temperature Range
TAI, TFI
S29GL064M
90, 10, 11
Model
Number
Packing
Type
Package Description
(Notes)
R0,R3,R4,R6,R7
TS048 (2, 3, 5)
R1,R2
TS056 (2, 3, 5)
TBI, TCI
R2,R7
TAI, TDI
R9
BAI, BFI
R0,R3,R4,R5
FAI, FFI
R1,R2,R3,R4,R5
0,2,3
(Note 1)
FPT-48P-M19 (3, 6)
TSOP
FPT-56P-M01 (3, 6)
FBE063 (4, 6)
Fine-Pitch BGA
LAA064 (4)
Fortified BGA
Notes:
1. Type 0 is standard. Specify others as required: TSOPs can be packed in Types 0 and 3; BGAs can be packed in Types 0, 2, or 3.
2. This package is recommended for new designs using TSOPs.
3. TSOP package marking omits packing type designator from the ordering part number.
4. BGA package marking omits leading “S29” and packing type designator from the ordering part number.
5. 100% Matte Sn is used for Pb-free TSOP plating.
6. SnBi is used for Pb-free TSOP plating.
Valid Combinations
Valid Combinations list configurations planned to be supported in volume for this device. Consult your local sales office to
confirm availability of specific valid combinations and to check on newly released combinations.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
19
D a t a
S h e e t
Ordering Information: S29GL128M
This product has been retired and is not recommended for designs. For new and current designs, S29GL128N supersedes S29GL128M, and is the
factory-recommended migration path. Please refer to the S29GL-N Datasheet for specifications and ordering information.
Standard products are available in several packages and operating ranges. The order number
(Valid Combination) is formed by a combination of the following:
S29GL128M
90
T
A
I
R1
0
PACKING TYPE
0
2
3
= Tray
= 7” Tape and Reel
= 13” Tape and Reel
Model Number
R1
R2
R8
R9
= x8/x16, VCC=3.0-3.6V, Uniform sector device, highest address
sector protected when WP#/ACC=VIL
= x8/x16, VCC=3.0-3.6V, Uniform sector device, lowest address sector
protected when WP#/ACC=VIL
= x8/x16, VCC=3.0-3.6V, Uniform sector device, highest address
sector protected when WP#/ACC=VIL, FPT-56P-M01 package only
= x8/x16, VCC=3.0-3.6V, Uniform sector device, lowest address sector
protected when WP#/ACC=VIL, FPT-56P-M01 package only
TEMPERATURE RANGE
I
= Industrial (–40°C to +85°C)
PACKAGE MATERIAL SET
A
F
D
= Standard
= Pb-Free
= Pb-Free
PACKAGE TYPE
T
F
= Thin Small Outline Package (TSOP) Standard Pinout
= Fortified Ball-Grid Array Package
SPEED OPTION
See Product Selector Guide and Valid Combinations
DEVICE NUMBER/DESCRIPTION
S29GL128M
128 Megabit Page-Mode Flash Memory Manufactured using 0.23 µm MirrorBit™
Process Technology, 3.0 Volt-only Read, Program, and Erase
Table 3.
S29GL128M Ordering Options
S29GL128M Valid Combinations
Base Ordering
Part Number
Speed
Option
S29GL128M
90, 10, 11
(Note 7)
Package Type, Material,
& Temperature Range
Model
Number
TAI, TFI
R1, R2
TAI, TDI
R9
FAI, FFI
R1, R2
Packing
Type
Package Descriptions
(Notes)
TS056 (2, 3, 5)
0, 2, 3 (Note 1)
TSOP
FPT-56P-M01 (3, 6)
LAA064 (4)
Fortified-BGA
Notes:
1. Type 0 is standard. Specify others as required: TSOPs can be packed in Types 0 and 3; BGAs can be packed in Types 0, 2, or 3.
2. This package is recommended for new designs using TSOPs.
3. TSOP package marking omits packing type designator from the ordering part number.
4. BGA package marking omits leading “S29” and packing type designator from the ordering part number.
5. 100% Matte Sn is used for Pb-free TSOP plating.
6. SnBi is used for Pb-free TSOP plating.
7. Contact your Spansion representative for availability of the 90ns speed option for LAA064.
Valid Combinations
Valid Combinations list configurations planned to be supported in volume for this device. Consult your local sales office to
confirm availability of specific valid combinations and to check on newly released combinations.
20
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Ordering Information: S29GL256M
This product has been retired and is not recommended for designs. For new and current designs, S29GL256N supersedes S29GL256M, and is the
factory-recommended migration path. Please refer to the S29GL-N Datasheet for specifications and ordering information.
Standard products are available in several packages and operating ranges. The order number
(Valid Combination) is formed by a combination of the following:
S29GL256M
11
T
A
I
R1
0
PACKING TYPE
0
2
3
= Tray
= 7” Tape and Reel
= 13” Tape and Reel
Model Number
R1
R2
= x8/x16, VCC=3.0-3.6V, Uniform sector device, highest address
sector protected when WP#/ACC=VIL
= x8/x16, VCC=3.0-3.6V, Uniform sector device, lowest address sector
protected when WP#/ACC=VIL
TEMPERATURE RANGE
I
= Industrial (–40°C to +85°C)
PACKAGE MATERIAL SET
A
F
= Standard
= Pb-Free
PACKAGE TYPE
T
F
= Thin Small Outline Package (TSOP) Standard Pinout
= Fortified Ball-Grid Array Package
SPEED OPTION
See Product Selector Guide and Valid Combinations
DEVICE NUMBER/DESCRIPTION
S29GL256M
256 Megabit Page-Mode Flash Memory Manufactured using 0.23 µm MirrorBit™
Process Technology, 3.0 Volt-only Read, Program, and Erase
Table 4.
S29GL256M Ordering Options
S29GL256M Valid Combinations
Device
Number
Speed
Option
S29GL256M
10, 11
(Note 5)
Package, Material,
& Temperature Range
TAI,TFI
FAI,FFI
Model
Number
Packing
Type
R1,R2
0,2,3
(Note 1)
Package Description
(Notes)
TS056 (2, 3, 4)
TSOP
LAC064 (3)
Fortified BGA
Notes:
1. Type 0 is standard. Specify others as required: TSOPs can be packed in Types 0 and 3; BGAs can be packed in Types 0, 2, or 3.
2. TSOP package marking omits the packing type designator from the ordering part number.
3. BGA package marking omits leading “S29” and packing type designator from the ordering part number.
4. 100% Matte Sn is used for Pb-free TSOP plating.
5. Contact your Spansion representative for availability of the 100 ns speed option.
Valid Combinations
Valid Combinations list configurations planned to be supported in volume for this device. Consult your local sales office to
confirm availability of specific valid combinations and to check on newly released combinations.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
21
D a t a
S h e e t
Device Bus Operations
This section describes the requirements and use of the device bus operations, which are initiated
through the internal command register. The command register itself does not occupy any addressable memory location. The register is a latch used to store the commands, along with the
address and data information needed to execute the command. The contents of the register serve
as inputs to the internal state machine. The state machine outputs dictate the function of the device. Table 5 lists the device bus operations, the inputs and control levels they require, and the
resulting output. The following subsections describe each of these operations in further detail.
Table 5.
Operation
CE#
Device Bus Operations
OE
WE# RESET#
#
WP#
AC
C
Addresses
(Note 1)
DQ0–
DQ7
BYTE#
= VIH
DOUT
BYTE#
= VIL
Read
L
L
H
H
X
X
AIN
Write (Program/Erase)
L
H
L
H
(Note 3)
X
AIN
(Note 4) (Note 4)
L
H
L
H
(Note 3) VHH
AIN
(Note 4) (Note 4)
X
H
X
High-Z
High-Z
High-Z
X
High-Z
High-Z
High-Z
Accelerated Program
DOUT
DQ8–DQ15
DQ8–DQ14
= High-Z,
DQ15 = A-1
VCC ±
0.3 V
X
X
VCC ±
0.3 V
Output Disable
L
H
H
H
X
X
Reset
X
X
X
L
X
X
X
High-Z
High-Z
High-Z
(Note 4)
X
X
(Note 4)
X
X
Standby
Sector Group Protect
(Note 2)
L
H
L
VID
H
X
SA, A6 =L,
A3=L, A2=L,
A1=H, A0=L
Sector Group Unprotect
(Note 2)
L
H
L
VID
H
X
SA, A6=H,
A3=L, A2=L,
A1=H, A0=L
Temporary Sector
Group Unprotect
X
X
X
VID
H
X
AIN
(Note 4) (Note 4)
High-Z
Legend: L = Logic Low = VIL, H = Logic High = VIH, VID = 11.5–12.5 V,
VHH = 11.5 V – 12.5 V, X = Don’t Care, SA = Sector Address, AIN = Address In,
DIN = Data In, DOUT = Data Out
Notes:
1. Addresses are Amax:A0 in word mode; Amax:A-1 in byte mode. Sector addresses are Amax:A15
in both modes.
2. The sector protect and sector unprotect functions may also be implemented via programming
equipment. See the “Sector Group Protection and Unprotection” section.
3. If WP# = VIL, the first or last sector remains protected (for uniform sector devices), and the two
outer boot sectors are protected (for boot sector devices). If WP# = VIH, the first or last sector, or
the two outer boot sectors are protected or unprotected as determined by the method described in
“Sector Group Protection and Unprotection”. All sectors are unprotected when shipped from the
factory (The Secured Silicon Sector may be factory protected depending on version ordered.)
4. DIN or DOUT as required by command sequence, data polling, or sector protect algorithm (see
Figure 2).
Word/Byte Configuration
The BYTE# pin controls whether the device data I/O pins operate in the byte or word configuration. If the BYTE# pin is set at logic ‘1’, the device is in word configuration, DQ0–DQ15 are active
and controlled by CE# and OE#.
If the BYTE# pin is set at logic ‘0’, the device is in byte configuration, and only data I/O pins DQ0–
DQ7 are active and controlled by CE# and OE#. The data I/O pins DQ8–DQ14 are tri-stated, and
the DQ15 pin is used as an input for the LSB (A-1) address function.
Requirements for Reading Array Data
To read array data from the outputs, the system must drive the CE# and OE# pins to VIL. CE# is
the power control and selects the device. OE# is the output control and gates array data to the
output pins. WE# should remain at VIH.
22
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
The internal state machine is set for reading array data upon device power-up, or after a hardware
reset. This ensures that no spurious alteration of the memory content occurs during the power
transition. No command is necessary in this mode to obtain array data. Standard microprocessor
read cycles that assert valid addresses on the device address inputs produce valid data on the
device data outputs. The device remains enabled for read access until the command register contents are altered.
See Reading Array Data for more information. See AC Characteristics for timing specifications and
the timing diagram. See DC Characteristics for the active current specification on reading array
data.
Page Mode Read
The device is capable of fast page mode read and is compatible with the page mode Mask ROM
read operation. This mode provides faster read access speed for random locations within a page.
The page size of the device is 4 words/8 bytes. The appropriate page is selected by the higher
address bits A(max)–A2. Address bits A1–A0 in word mode (A1–A-1 in byte mode) determine the
specific word within a page. This is an asynchronous operation; the microprocessor supplies the
specific word location.
The random or initial page access is equal to tACC or tCE and subsequent page read accesses (as
long as the locations specified by the microprocessor falls within that page) is equivalent to tPACC.
When CE# is deasserted and reasserted for a subsequent access, the access time is tACC or tCE.
Fast page mode accesses are obtained by keeping the “read-page addresses” constant and
changing the “intra-read page” addresses.
Writing Commands/Command Sequences
To write a command or command sequence (which includes programming data to the device and
erasing sectors of memory), the system must drive WE# and CE# to VIL, and OE# to VIH.
The device features an Unlock Bypass mode to facilitate faster programming. Once the device
enters the Unlock Bypass mode, only two write cycles are required to program a word, instead of
four. Word Program Command Sequence contains details on programming data to the device
using both standard and Unlock Bypass command sequences.
An erase operation can erase one sector, multiple sectors, or the entire device. Table 6 and
Table 16 indicates the address space that each sector occupies.
See DC Characteristics for the active current specification for the write mode. AC Characteristics
contains timing specification tables and timing diagrams for write operations.
Write Buffer
Write Buffer Programming allows the system write to a maximum of 16 words/32 bytes in one
programming operation. This results in faster effective programming time than the standard programming algorithms. See Write Buffer Programming for more information.
Accelerated Program Operation
The device offers accelerated program operations through the ACC function. This is one of two
functions provided by the WP#/ACC or ACC pin, depending on model number. This function is primarily intended to allow faster manufacturing throughput at the factory.
If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock
Bypass mode, temporarily unprotects any protected sector groups, and uses the higher voltage
on the pin to reduce the time required for program operations. The system would use a two-cycle
program command sequence as required by the Unlock Bypass mode. Removing VHH from the
WP#/ACC or ACC pin, depending on model number, returns the device to normal operation. Note
that the WP#/ACC or ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result. WP# has an internal pullup; when unconnected, WP# is at
VIH.
Autoselect Functions
If the system writes the autoselect command sequence, the device enters the autoselect mode.
The system can then read autoselect codes from the internal register (which is separate from the
memory array) on DQ7–DQ0. Standard read cycle timings apply in this mode. See Autoselect
Mode and Autoselect Command Sequence for more information.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
23
D a t a
S h e e t
Standby Mode
When the system is not reading or writing to the device, it can place the device in the standby
mode. In this mode, current consumption is greatly reduced, and the outputs are placed in the
high impedance state, independent of the OE# input.
The device enters the CMOS standby mode when the CE# and RESET# pins are both held at VIO
± 0.3 V. (Note that this is a more restricted voltage range than VIH.) If CE# and RESET# are held
at VIH, but not within VIO ± 0.3 V, the device is in the standby mode, but the standby current is
greater. The device requires standard access time (tCE) for read access when the device is in either of these standby modes, before it is ready to read data.
If the device is deselected during erasure or programming, the device draws active current until
the operation is completed.
See DC Characteristics for the standby current specification.
Automatic Sleep Mode
The automatic sleep mode minimizes Flash device energy consumption. The device automatically
enables this mode when addresses remain stable for tACC + 30 ns. The automatic sleep mode is
independent of the CE#, WE#, and OE# control signals. Standard address access timings provide
new data when addresses are changed. While in sleep mode, output data is latched and always
available to the system. See DC Characteristics for the automatic sleep mode current
specification.
RESET#: Hardware Reset Pin
The RESET# pin provides a hardware method of resetting the device to reading array data. When
the RESET# pin is driven low for at least a period of tRP, the device immediately terminates any
operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array
data. The operation that was interrupted should be reinitiated once the device is ready to accept
another command sequence, to ensure data integrity.
Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS±0.3 V, the
device draws CMOS standby current (ICC5). If RESET# is held at VIL but not within VSS±0.3 V, the
standby current is greater.
The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset
the Flash memory, enabling the system to read the boot-up firmware from the Flash memory.
See AC Characteristics for RESET# parameters and to Figure 15 for the timing diagram.
Output Disable Mode
When the OE# input is at VIH, output from the device is disabled. The output pins are placed in
the high impedance state.
24
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S29GL032M (Model R0) Sector Addresses
8-bit
Address
Range
A21–A16
Sector
Sector
Table 6.
S h e e t
8-bit
Address
Range
A21–A16
SA0
0
0
0
0
0
0
000000–00FFFF
SA32
1
0
0
0
0
0
200000–20FFFF
SA1
0
0
0
0
0
1
010000–01FFFF
SA33
1
0
0
0
0
1
210000–21FFFF
SA2
0
0
0
0
1
0
020000–02FFFF
SA34
1
0
0
0
1
0
220000–22FFFF
SA3
0
0
0
0
1
1
030000–03FFFF
SA35
1
0
0
0
1
1
230000–23FFFF
SA4
0
0
0
1
0
0
040000–04FFFF
SA36
1
0
0
1
0
0
240000–24FFFF
SA5
0
0
0
1
0
1
050000–05FFFF
SA37
1
0
0
1
0
1
250000–25FFFF
SA6
0
0
0
1
1
0
060000–06FFFF
SA38
1
0
0
1
1
0
260000–26FFFF
SA7
0
0
0
1
1
1
070000–07FFFF
SA39
1
0
0
1
1
1
270000–27FFFF
SA8
0
0
1
0
0
0
080000–08FFFF
SA40
1
0
1
0
0
0
280000–28FFFF
SA9
0
0
1
0
0
1
090000–09FFFF
SA41
1
0
1
0
0
1
290000–29FFFF
SA10
0
0
1
0
1
0
0A0000–0AFFFF
SA42
1
0
1
0
1
0
2A0000–2AFFFF
SA11
0
0
1
0
1
1
0B0000–0BFFFF
SA43
1
0
1
0
1
1
2B0000–2BFFFF
SA12
0
0
1
1
0
0
0C0000–0CFFFF
SA44
1
0
1
1
0
0
2C0000–2CFFFF
SA13
0
0
1
1
0
1
0D0000–0DFFFF
SA45
1
0
1
1
0
1
2D0000–2DFFFF
SA14
0
0
1
1
1
0
0E0000–0EFFFF
SA46
1
0
1
1
1
0
2E0000–2EFFFF
SA15
0
0
1
1
1
1
0F0000–0FFFFF
SA47
1
0
1
1
1
1
2F0000–2FFFFF
SA16
0
1
0
0
0
0
100000–10FFFF
SA48
1
1
0
0
0
0
300000–30FFFF
SA17
0
1
0
0
0
1
110000–11FFFF
SA49
1
1
0
0
0
1
310000–31FFFF
SA18
0
1
0
0
1
0
120000–12FFFF
SA50
1
1
0
0
1
0
320000–32FFFF
SA19
0
1
0
0
1
1
130000–13FFFF
SA51
1
1
0
0
1
1
330000–33FFFF
SA20
0
1
0
1
0
0
140000–14FFFF
SA52
1
1
0
1
0
0
340000–34FFFF
SA21
0
1
0
1
0
1
150000–15FFFF
SA53
1
1
0
1
0
1
350000–35FFFF
SA22
0
1
0
1
1
0
160000–16FFFF
SA54
1
1
0
1
1
0
360000–36FFFF
SA23
0
1
0
1
1
1
170000–17FFFF
SA55
1
1
0
1
1
1
370000–37FFFF
SA24
0
1
1
0
0
0
180000–18FFFF
SA56
1
1
1
0
0
0
380000–38FFFF
SA25
0
1
1
0
0
1
190000–19FFFF
SA57
1
1
1
0
0
1
390000–39FFFF
SA26
0
1
1
0
1
0
1A0000–1AFFFF
SA58
1
1
1
0
1
0
3A0000–3AFFFF
SA27
0
1
1
0
1
1
1B0000–1BFFFF
SA59
1
1
1
0
1
1
3B0000–3BFFFF
SA28
0
1
1
1
0
0
1C0000–1CFFFF
SA60
1
1
1
1
0
0
3C0000–3CFFFF
SA29
0
1
1
1
0
1
1D0000–1DFFFF
SA61
1
1
1
1
0
1
3D0000–3DFFFF
SA30
0
1
1
1
1
0
1E0000–1EFFFF
SA62
1
1
1
1
1
0
3E0000–3EFFFF
SA31
0
1
1
1
1
1
1F0000–1FFFFF
SA63
1
1
1
1
1
1
3F0000–3FFFFF
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
25
D a t a
S29GL032M (Models R1, R2) Sector Addresses
A20-A15
Sector
Size
(KB/
Kwords)
8-bit
Address
Range
16-bit
Address
Range
Sector
Size
(KB/
Kwords)
8-bit
Address
Range
16-bit
Address
Range
SA0
0 0 0 0 0 0
64/32
000000–00FFFF
000000–007FFF
SA1
0 0 0 0 0 1
64/32
010000–01FFFF
008000–00FFFF
SA32 1 0 0 0 0 0
64/32
200000–20FFFF
100000–107FFF
SA33 1 0 0 0 0 1
64/32
210000–21FFFF
108000–10FFFF
SA2
0 0 0 0 1 0
64/32
020000–02FFFF
010000–017FFF
SA3
0 0 0 0 1 1
64/32
030000–03FFFF
018000–01FFFF
SA34 1 0 0 0 1 0
64/32
220000–22FFFF
110000–117FFF
SA35 1 0 0 0 1 1
64/32
230000–23FFFF
118000–11FFFF
SA4
0 0 0 1 0 0
64/32
040000–04FFFF
020000–027FFF
SA5
0 0 0 1 0 1
64/32
050000–05FFFF
028000–02FFFF
SA36 1 0 0 1 0 0
64/32
240000–24FFFF
120000–127FFF
SA37 1 0 0 1 0 1
64/32
250000–25FFFF
SA6
0 0 0 1 1 0
64/32
060000–06FFFF
030000–037FFF
128000–12FFFF
SA38 1 0 0 1 1 0
64/32
260000–26FFFF
130000–137FFF
SA7
0 0 0 1 1 1
64/32
070000–07FFFF
SA8
0 0 1 0 0 0
64/32
080000–08FFFF
038000–03FFFF
SA39 1 0 0 1 1 1
64/32
270000–27FFFF
138000–13FFFF
040000–047FFF
SA40 1 0 1 0 0 0
64/32
280000–28FFFF
140000–147FFF
SA9
0 0 1 0 0 1
64/32
090000–09FFFF
048000–04FFFF
SA41 1 0 1 0 0 1
64/32
290000–29FFFF
148000–14FFFF
SA10 0 0 1 0 1 0
64/32
0A0000–0AFFFF
SA11 0 0 1 0 1 1
64/32
0B0000–0BFFFF
050000–057FFF
SA42 1 0 1 0 1 0
64/32
2A0000–2AFFFF
150000–157FFF
058000–05FFFF
SA43 1 0 1 0 1 1
64/32
2B0000–2BFFFF
158000–15FFFF
SA12 0 0 1 1 0 0
64/32
SA13 0 0 1 1 0 1
64/32
0C0000–0CFFFF
060000–067FFF
SA44 1 0 1 1 0 0
64/32
2C0000–2CFFFF
160000–167FFF
0D0000–0DFFFF
068000–06FFFF
SA45 1 0 1 1 0 1
64/32
2D0000–2DFFFF
SA14 0 0 1 1 1 0
64/32
0E0000–0EFFFF
168000–16FFFF
070000–077FFF
SA46 1 0 1 1 1 0
64/32
2E0000–2EFFFF
170000–177FFF
SA15 0 0 1 1 1 1
64/32
SA16 0 1 0 0 0 0
64/32
0F0000–0FFFFF
078000–07FFFF
SA47 1 0 1 1 1 1
64/32
2F0000–2FFFFF
178000–17FFFF
100000–10FFFF
080000–087FFF
SA48 1 1 0 0 0 0
64/32
300000–30FFFF
180000–187FFF
SA17 0 1 0 0 0 1
64/32
110000–11FFFF
088000–08FFFF
SA49 1 1 0 0 0 1
64/32
310000–31FFFF
188000–18FFFF
SA18 0 1 0 0 1 0
SA19 0 1 0 0 1 1
64/32
120000–12FFFF
090000–097FFF
SA50 1 1 0 0 1 0
64/32
320000–32FFFF
190000–197FFF
64/32
130000–13FFFF
098000–09FFFF
SA51 1 1 0 0 1 1
64/32
330000–33FFFF
198000–19FFFF
SA20 0 1 0 1 0 0
64/32
140000–14FFFF
0A0000–0A7FFF
SA52 1 1 0 1 0 0
64/32
340000–34FFFF
1A0000–1A7FFF
SA21 0 1 0 1 0 1
64/32
150000–15FFFF
0A8000–0AFFFF
SA53 1 1 0 1 0 1
64/32
350000–35FFFF
1A8000–1AFFFF
SA22 0 1 0 1 1 0
64/32
160000–16FFFF
0B0000–0B7FFF
SA54 1 1 0 1 1 0
64/32
360000–36FFFF
1B0000–1B7FFF
SA23 0 1 0 1 1 1
64/32
170000–17FFFF
0B8000–0BFFFF
SA55 1 1 0 1 1 1
64/32
370000–37FFFF
1B8000–1BFFFF
SA24 0 1 1 0 0 0
64/32
180000–18FFFF
0C0000–0C7FFF
SA56 1 1 1 0 0 0
64/32
380000–38FFFF
1C0000–1C7FFF
SA25 0 1 1 0 0 1
64/32
190000–19FFFF
0C8000–0CFFFF
SA57 1 1 1 0 0 1
64/32
390000–39FFFF
1C8000–1CFFFF
SA26 0 1 1 0 1 0
64/32
1A0000–1AFFFF
0D0000–0D7FFF
SA58 1 1 1 0 1 0
64/32
3A0000–3AFFFF
1D0000–1D7FFF
SA27 0 1 1 0 1 1
64/32
1B0000–1BFFFF
0D8000–0DFFFF
SA59 1 1 1 0 1 1
64/32
3B0000–3BFFFF
1D8000–1DFFFF
SA28 0 1 1 1 0 0
64/32
1C0000–1CFFFF
0E0000–0E7FFF
SA60 1 1 1 1 0 0
64/32
3C0000–3CFFFF
1E0000–1E7FFF
SA29 0 1 1 1 0 1
64/32
1D0000–1DFFFF
0E8000–0EFFFF
SA61 1 1 1 1 0 1
64/32
3D0000–3DFFFF
1E8000–1EFFFF
SA30 0 1 1 1 1 0
64/32
1E0000–1EFFFF
0F0000–0F7FFF
SA62 1 1 1 1 1 0
64/32
3E0000–3EFFFF
1F0000–1F7FFF
SA31 0 1 1 1 1 1
64/32
1F0000–1FFFFF
0F8000–0FFFFF
SA63 1 1 1 1 1 1
64/32
3F0000–3FFFFF
1F8000–1FFFFF
26
Sector
Sector
Table 7.
S h e e t
A20-A15
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Sector
Sector
Table 8. S29GL032M (Model R3)
Top Boot Sector Addresses
A20–A12
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
A20–A12
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
SA0
000000xxx
64/32
000000h–00FFFFh
00000h–07FFFh
SA1
000001xxx
64/32
010000h–01FFFFh
08000h–0FFFFh
SA36
100100xxx
64/32
240000h–24FFFFh
120000h–127FFFh
SA37
100101xxx
64/32
250000h–25FFFFh
128000h–12FFFFh
SA2
000010xxx
64/32
020000h–02FFFFh
10000h–17FFFh
SA3
000011xxx
64/32
030000h–03FFFFh
18000h–1FFFFh
SA38
100110xxx
64/32
260000h–26FFFFh
130000h–137FFFh
SA39
100111xxx
64/32
270000h–27FFFFh
138000h–13FFFFh
SA4
000100xxx
64/32
040000h–04FFFFh
20000h–27FFFh
SA5
000101xxx
64/32
050000h–05FFFFh
28000h–2FFFFh
SA40
101000xxx
64/32
280000h–28FFFFh
140000h–147FFFh
SA41
101001xxx
64/32
290000h–29FFFFh
SA6
000110xxx
64/32
060000h–06FFFFh
30000h–37FFFh
SA42
148000h–14FFFFh
101010xxx
64/32
2A0000h–2AFFFFh
150000h–157FFFh
SA7
000111xxx
64/32
070000h–07FFFFh
38000h–3FFFFh
SA43
101011xxx
64/32
2B0000h–2BFFFFh
158000h–15FFFFh
SA8
001000xxx
64/32
080000h–08FFFFh
40000h–47FFFh
SA44
101100xxx
64/32
2C0000h–2CFFFFh
160000h–167FFFh
SA9
001001xxx
64/32
090000h–09FFFFh
48000h–4FFFFh
SA45
101101xxx
64/32
2D0000h–2DFFFFh
168000h–16FFFFh
SA10
001010xxx
64/32
0A0000h–0AFFFFh
50000h–57FFFh
SA46
101110xxx
64/32
2E0000h–2EFFFFh
170000h–177FFFh
SA11
001011xxx
64/32
0B0000h–0BFFFFh
58000h–5FFFFh
SA47
101111xxx
64/32
2F0000h–2FFFFFh
178000h–17FFFFh
SA12
001100xxx
64/32
0C0000h–0CFFFFh
60000h–67FFFh
SA48
110000xxx
64/32
300000h–30FFFFh
180000h–187FFFh
SA13
001101xxx
64/32
0D0000h–0DFFFFh
68000h–6FFFFh
SA49
110001xxx
64/32
310000h–31FFFFh
188000h–18FFFFh
SA14
001101xxx
64/32
0E0000h–0EFFFFh
70000h–77FFFh
SA50
110010xxx
64/32
320000h–32FFFFh
190000h–197FFFh
SA15
001111xxx
64/32
0F0000h–0FFFFFh
78000h–7FFFFh
SA51
110011xxx
64/32
330000h–33FFFFh
198000h–19FFFFh
SA16
010000xxx
64/32
100000h–00FFFFh
80000h–87FFFh
SA52
100100xxx
64/32
340000h–34FFFFh
1A0000h–1A7FFFh
SA17
010001xxx
64/32
110000h–11FFFFh
88000h–8FFFFh
SA53
110101xxx
64/32
350000h–35FFFFh
1A8000h–1AFFFFh
SA18
010010xxx
64/32
120000h–12FFFFh
90000h–97FFFh
SA54
110110xxx
64/32
360000h–36FFFFh
1B0000h–1B7FFFh
SA19
010011xxx
64/32
130000h–13FFFFh
98000h–9FFFFh
SA55
110111xxx
64/32
370000h–37FFFFh
1B8000h–1BFFFFh
SA20
010100xxx
64/32
140000h–14FFFFh
A0000h–A7FFFh
SA56
111000xxx
64/32
380000h–38FFFFh
1C0000h–1C7FFFh
SA21
010101xxx
64/32
150000h–15FFFFh
A8000h–AFFFFh
SA57
111001xxx
64/32
390000h–39FFFFh
1C8000h–1CFFFFh
SA22
010110xxx
64/32
160000h–16FFFFh
B0000h–B7FFFh
SA58
111010xxx
64/32
3A0000h–3AFFFFh
1D0000h–1D7FFFh
SA23
010111xxx
64/32
170000h–17FFFFh
B8000h–BFFFFh
SA59
111011xxx
64/32
3B0000h–3BFFFFh
1D8000h–1DFFFFh
SA24
011000xxx
64/32
180000h–18FFFFh
C0000h–C7FFFh
SA60
111100xxx
64/32
3C0000h–3CFFFFh
1E0000h–1E7FFFh
SA25
011001xxx
64/32
190000h–19FFFFh
C8000h–CFFFFh
SA61
111101xxx
64/32
3D0000h–3DFFFFh
1E8000h–1EFFFFh
SA26
011010xxx
64/32
1A0000h–1AFFFFh
D0000h–D7FFFh
SA62
111110xxx
64/32
3E0000h–3EFFFFh
1F0000h–1F7FFFh
SA27
011011xxx
64/32
1B0000h–1BFFFFh
D8000h–DFFFFh
SA63
111111000
8/4
3F0000h–3F1FFFh
1F8000h–1F8FFFh
SA28
011000xxx
64/32
1C0000h–1CFFFFh
E0000h–E7FFFh
SA64
111111001
8/4
3F2000h–3F3FFFh
1F9000h–1F9FFFh
SA29
011101xxx
64/32
1D0000h–1DFFFFh
E8000h–EFFFFh
SA65
111111010
8/4
3F4000h–3F5FFFh
1FA000h–1FAFFFh
SA30
011110xxx
64/32
1E0000h–1EFFFFh
F0000h–F7FFFh
SA66
111111011
8/4
3F6000h–3F7FFFh
1FB000h–1FBFFFh
SA31
011111xxx
64/32
1F0000h–1FFFFFh
F8000h–FFFFFh
SA67
111111100
8/4
3F8000h–3F9FFFh
1FC000h–1FCFFFh
SA32
100000xxx
64/32
200000h–20FFFFh
F9000h–107FFFh
SA68
111111101
8/4
3FA000h–3FBFFFh
1FD000h–1FDFFFh
SA33
100001xxx
64/32
210000h–21FFFFh 108000h–10FFFFh
SA69
111111110
8/4
3FC000h–3FDFFFh
1FE000h–1FEFFFh
SA34
100010xxx
64/32
220000h–22FFFFh 110000h–117FFFh
SA70
111111111
8/4
3FE000h–3FFFFFh
1FF000h–1FFFFFh
SA35
101011xxx
64/32
230000h–23FFFFh 118000h–11FFFFh
* Sector sizes are given in Kbytes/Kwords.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
27
D a t a
S h e e t
A20–A12
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
Sector
Sector
Table 9. S29GL032M (Model R4)
Bottom Boot Sector Addresses
A20–A12
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
SA0
000000000
8/4
000000h–001FFFh
00000h–00FFFh
SA19 001100xxx
64/32
0C0000h–0CFFFFh
60000h–67FFFh
SA1
000000001
8/4
002000h–003FFFh
01000h–01FFFh
SA20 001101xxx
64/32
0D0000h–0DFFFFh
68000h–6FFFFh
SA2
000000010
8/4
004000h–005FFFh
02000h–02FFFh
SA21 001101xxx
64/32
0E0000h–0EFFFFh
70000h–77FFFh
SA3
000000011
8/4
006000h–007FFFh
03000h–03FFFh
SA22 001111xxx
64/32
0F0000h–0FFFFFh
78000h–7FFFFh
80000h–87FFFh
SA4
000000100
8/4
008000h–009FFFh
04000h–04FFFh
SA23 010000xxx
64/32
100000h–00FFFFh
SA5
000000101
8/4
00A000h–00BFFFh
05000h–05FFFh
SA24 010001xxx
64/32
110000h–11FFFFh
88000h–8FFFFh
SA6
000000110
8/4
00C000h–00DFFFh
06000h–06FFFh
SA25 010010xxx
64/32
120000h–12FFFFh
90000h–97FFFh
SA7
000000111
8/4
00E000h–00FFFFFh
07000h–07FFFh
SA26 010011xxx
64/32
130000h–13FFFFh
98000h–9FFFFh
SA8
000001xxx
64/32
010000h–01FFFFh
08000h–0FFFFh
SA27 010100xxx
64/32
140000h–14FFFFh
A0000h–A7FFFh
SA9
000010xxx
64/32
020000h–02FFFFh
10000h–17FFFh
SA28 010101xxx
64/32
150000h–15FFFFh
A8000h–AFFFFh
SA10 000011xxx
64/32
030000h–03FFFFh
18000h–1FFFFh
SA29 010110xxx
64/32
160000h–16FFFFh
B0000h–B7FFFh
SA11 000100xxx
64/32
040000h–04FFFFh
20000h–27FFFh
SA30 010111xxx
64/32
170000h–17FFFFh
B8000h–BFFFFh
SA12 000101xxx
64/32
050000h–05FFFFh
28000h–2FFFFh
SA31 011000xxx
64/32
180000h–18FFFFh
C0000h–C7FFFh
SA13 000110xxx
64/32
060000h–06FFFFh
30000h–37FFFh
SA32 011001xxx
64/32
190000h–19FFFFh
C8000h–CFFFFh
SA14 000111xxx
64/32
070000h–07FFFFh
38000h–3FFFFh
SA33 011010xxx
64/32
1A0000h–1AFFFFh
D0000h–D7FFFh
SA15 001000xxx
64/32
080000h–08FFFFh
40000h–47FFFh
SA34 011011xxx
64/32
1B0000h–1BFFFFh
D8000h–DFFFFh
SA16 001001xxx
64/32
090000h–09FFFFh
48000h–4FFFFh
SA35 011000xxx
64/32
1C0000h–1CFFFFh
E0000h–E7FFFh
SA17 001010xxx
64/32
0A0000h–0AFFFFh
50000h–57FFFh
SA36 011101xxx
64/32
1D0000h–1DFFFFh
E8000h–EFFFFh
SA18 001011xxx
64/32
0B0000h–0BFFFFh
58000h–5FFFFh
SA37 011110xxx
64/32
1E0000h–1EFFFFh
F0000h–F7FFFh
SA38 011111xxx
64/32
1F0000h–1FFFFFh
F8000h–FFFFFh
SA55 110000xxx
64/32
300000h–30FFFFh
180000h–187FFFh
SA39 100000xxx
64/32
200000h–20FFFFh
F9000h–107FFFh
SA56 110001xxx
64/32
310000h–31FFFFh
188000h–18FFFFh
SA40 100001xxx
64/32
210000h–21FFFFh
108000h–10FFFFh
SA57 110010xxx
64/32
320000h–32FFFFh
190000h–197FFFh
SA41 100010xxx
64/32
220000h–22FFFFh
110000h–117FFFh
SA58 110011xxx
64/32
330000h–33FFFFh
198000h–19FFFFh
SA42 101011xxx
64/32
230000h–23FFFFh
118000h–11FFFFh
SA59 100100xxx
64/32
340000h–34FFFFh
1A0000h–1A7FFFh
SA43 100100xxx
64/32
240000h–24FFFFh
120000h–127FFFh
SA60 110101xxx
64/32
350000h–35FFFFh
1A8000h–1AFFFFh
SA44 100101xxx
64/32
250000h–25FFFFh
128000h–12FFFFh
SA61 110110xxx
64/32
360000h–36FFFFh
1B0000h–1B7FFFh
SA45 100110xxx
64/32
260000h–26FFFFh
130000h–137FFFh
SA62 110111xxx
64/32
370000h–37FFFFh
1B8000h–1BFFFFh
SA46 100111xxx
64/32
270000h–27FFFFh
138000h–13FFFFh
SA63 111000xxx
64/32
380000h–38FFFFh
1C0000h–1C7FFFh
1C8000h–1CFFFFh
SA47 101000xxx
64/32
280000h–28FFFFh
140000h–147FFFh
SA64 111001xxx
64/32
390000h–39FFFFh
SA48 101001xxx
64/32
290000h–29FFFFh
148000h–14FFFFh
SA65 111010xxx
64/32
3A0000h–3AFFFFh 1D0000h–1D7FFFh
SA49 101010xxx
64/32
2A0000h–2AFFFFh
150000h–157FFFh
SA66 111011xxx
64/32
3B0000h–3BFFFFh
1D8000h–1DFFFFh
SA50 101011xxx
64/32
2B0000h–2BFFFFh
158000h–15FFFFh
SA67 111100xxx
64/32
3C0000h–3CFFFFh
1E0000h–1E7FFFh
SA51 101100xxx
64/32
2C0000h–2CFFFFh
160000h–167FFFh
SA68 111101xxx
64/32
3D0000h–3DFFFFh
1E8000h–1EFFFFh
SA52 101101xxx
64/32
2D0000h–2DFFFFh
168000h–16FFFFh
SA69 111110xxx
64/32
3E0000h–3EFFFFh
1F0000h–1F7FFFh
SA53 101110xxx
64/32
2E0000h–2EFFFFh
170000h–177FFFh
SA70 111111xxx
64/32
3F0000h–3FFFFFh
1F8000h–1FFFFFh
SA54 101111xxx
64/32
2F0000h–2FFFFFh
178000h–17FFFFh
* Sector sizes are given in Kbytes/Kwords.
28
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Sector
Sector
Sector
Table 10. S29GL064M (Model R0) Sector Addresses
A22–A16
8-bit
Address
Range
A22–A16
8-bit
Address
Range
A22–A16
8-bit
Address
Range
SA0
0 0 0 0 0 0 0
000000–00FFFF
SA1
0 0 0 0 0 0 1
010000–01FFFF
SA43
SA44
0 1 0 1 0 1 1
2B0000–2BFFFF
0 1 0 1 1 0 0
2C0000–2CFFFF
SA86
1 0 1 0 1 1 0
560000–56FFFF
SA87
1 0 1 0 1 1 1
570000–57FFFF
SA2
0 0 0 0 0 1 0
020000–02FFFF
SA3
0 0 0 0 0 1 1
030000–03FFFF
SA45
0 1 0 1 1 0 1
SA46
0 1 0 1 1 1 0
2D0000–2DFFFF
SA88
1 0 1 1 0 0 0
580000–58FFFF
2E0000–2EFFFF
SA89
1 0 1 1 0 0 1
590000–59FFFF
SA4
0 0 0 0 1 0 0
SA5
0 0 0 0 1 0 1
040000–04FFFF
SA47
050000–05FFFF
SA48
0 1 0 1 1 1 1
2F0000–2FFFFF
SA90
1 0 1 1 0 1 0
5A0000–5AFFFF
0 1 1 0 0 0 0
300000–30FFFF
SA91
1 0 1 1 0 1 1
5B0000–5BFFFF
SA6
0 0 0 0 1 1 0
060000–06FFFF
SA49
0 1 1 0 0 0 1
310000–31FFFF
SA92
1 0 1 1 1 0 0
5C0000–5CFFFF
SA7
0 0 0 0 1 1 1
SA8
0 0 0 1 0 0 0
070000–07FFFF
SA50
0 1 1 0 0 1 0
320000–32FFFF
SA93
1 0 1 1 1 0 1
5D0000–5DFFFF
080000–08FFFF
SA51
0 1 1 0 0 1 1
330000–33FFFF
SA94
1 0 1 1 1 1 0
SA9
5E0000–5EFFFF
0 0 0 1 0 0 1
090000–09FFFF
SA52
0 1 1 0 1 0 0
340000–34FFFF
SA95
1 0 1 1 1 1 1
5F0000–5FFFFF
SA10
0 0 0 1 0 1 0
0A0000–0AFFFF
SA53
0 1 1 0 1 0 1
350000–35FFFF
SA96
1 1 0 0 0 0 0
600000–60FFFF
SA11
0 0 0 1 0 1 1
0B0000–0BFFFF
SA54
0 1 1 0 1 1 0
360000–36FFFF
SA97
1 1 0 0 0 0 1
610000–61FFFF
SA12
0 0 0 1 1 0 0
0C0000–0CFFFF
SA55
0 1 1 0 1 1 1
370000–37FFFF
SA98
1 1 0 0 0 1 0
620000–62FFFF
SA13
0 0 0 1 1 0 1
0D0000–0DFFFF
SA56
0 1 1 1 0 0 0
380000–38FFFF
SA99
1 1 0 0 0 1 1
630000–63FFFF
SA14
0 0 0 1 1 1 0
0E0000–0EFFFF
SA57
0 1 1 1 0 0 1
390000–39FFFF
SA100
1 1 0 0 1 0 0
640000–64FFFF
SA15
0 0 0 1 1 1 1
0F0000–0FFFFF
SA58
0 1 1 1 0 1 0
3A0000–3AFFFF
SA101
1 1 0 0 1 0 1
650000–65FFFF
SA16
0 0 1 0 0 0 0
100000–10FFFF
SA59
0 1 1 1 0 1 1
3B0000–3BFFFF
SA102
1 1 0 0 1 1 0
660000–66FFFF
SA17
0 0 1 0 0 0 1
110000–11FFFF
SA60
0 1 1 1 1 0 0
3C0000–3CFFFF
SA103
1 1 0 0 1 1 1
670000–67FFFF
SA18
0 0 1 0 0 1 0
120000–12FFFF
SA61
0 1 1 1 1 0 1
3D0000–3DFFFF
SA104
1 1 0 1 0 0 0
680000–68FFFF
SA19
0 0 1 0 0 1 1
130000–13FFFF
SA62
0 1 1 1 1 1 0
3E0000–3EFFFF
SA105
1 1 0 1 0 0 1
690000–69FFFF
SA20
0 0 1 0 1 0 0
140000–14FFFF
SA63
0 1 1 1 1 1 1
3F0000–3FFFFF
SA106
1 1 0 1 0 1 0
6A0000–6AFFFF
SA21
0 0 1 0 1 0 1
150000–15FFFF
SA64
1 0 0 0 0 0 0
400000–40FFFF
SA107
1 1 0 1 0 1 1
6B0000–6BFFFF
SA22
0 0 1 0 1 1 0
160000–16FFFF
SA65
1 0 0 0 0 0 1
410000–41FFFF
SA108
1 1 0 1 1 0 0
6C0000–6CFFFF
SA23
0 0 1 0 1 1 1
170000–17FFFF
SA66
1 0 0 0 0 1 0
420000–42FFFF
SA109
1 1 0 1 1 0 1
6D0000–6DFFFF
SA24
0 0 1 1 0 0 0
180000–18FFFF
SA67
1 0 0 0 0 1 1
430000–43FFFF
SA110
1 1 0 1 1 1 0
6E0000–6EFFFF
SA25
0 0 1 1 0 0 1
190000–19FFFF
SA68
1 0 0 0 1 0 0
440000–44FFFF
SA111
1 1 0 1 1 1 1
6F0000–6FFFFF
SA26
0 0 1 1 0 1 0
1A0000–1AFFFF
SA69
1 0 0 0 1 0 1
450000–45FFFF
SA112
1 1 1 0 0 0 0
700000–70FFFF
SA27
0 0 1 1 0 1 1
1B0000–1BFFFF
SA70
1 0 0 0 1 1 0
460000–46FFFF
SA113
1 1 1 0 0 0 1
710000–71FFFF
SA28
0 0 1 1 1 0 0
1C0000–1CFFFF
SA71
1 0 0 0 1 1 1
470000–47FFFF
SA114
1 1 1 0 0 1 0
720000–72FFFF
SA29
0 0 1 1 1 0 1
1D0000–1DFFFF
SA72
1 0 0 1 0 0 0
480000–48FFFF
SA115
1 1 1 0 0 1 1
730000–73FFFF
SA30
0 0 1 1 1 1 0
1E0000–1EFFFF
SA73
1 0 0 1 0 0 1
490000–49FFFF
SA116
1 1 1 0 1 0 0
740000–74FFFF
SA31
0 0 1 1 1 1 1
1F0000–1FFFFF
SA74
1 0 0 1 0 1 0
4A0000–4AFFFF
SA117
1 1 1 0 1 0 1
750000–75FFFF
SA32
0 1 0 0 0 0 0
200000–20FFFF
SA75
1 0 0 1 0 1 1
4B0000–4BFFFF
SA118
1 1 1 0 1 1 0
760000–76FFFF
SA33
0 1 0 0 0 0 1
210000–21FFFF
SA76
1 0 0 1 1 0 0
4C0000–4CFFFF
SA119
1 1 1 0 1 1 1
770000–77FFFF
SA34
0 1 0 0 0 1 0
220000–22FFFF
SA77
1 0 0 1 1 0 1
4D0000–4DFFFF
SA120
1 1 1 1 0 0 0
780000–78FFFF
SA35
0 1 0 0 0 1 1
230000–23FFFF
SA78
1 0 0 1 1 1 0
4E0000–4EFFFF
SA121
1 1 1 1 0 0 1
790000–79FFFF
SA36
0 1 0 0 1 0 0
240000–24FFFF
SA79
1 0 0 1 1 1 1
4F0000–4FFFFF
SA122
1 1 1 1 0 1 0
7A0000–7AFFFF
SA37
0 1 0 0 1 0 1
250000–25FFFF
SA80
1 0 1 0 0 0 0
500000–50FFFF
SA123
1 1 1 1 0 1 1
7B0000–7BFFFF
SA38
0 1 0 0 1 1 0
260000–26FFFF
SA81
1 0 1 0 0 0 1
510000–51FFFF
SA124
1 1 1 1 1 0 0
7C0000–7CFFFF
SA39
0 1 0 0 1 1 1
270000–27FFFF
SA82
1 0 1 0 0 1 0
520000–52FFFF
SA125
1 1 1 1 1 0 1
7D0000–7DFFFF
SA40
0 1 0 1 0 0 0
280000–28FFFF
SA83
1 0 1 0 0 1 1
530000–53FFFF
SA126
1 1 1 1 1 1 0
7E0000–7EFFFF
SA41
0 1 0 1 0 0 1
290000–29FFFF
SA84
1 0 1 0 1 0 0
540000–54FFFF
SA127
1 1 1 1 1 1 1
7F0000–7FFFFF
SA42
0 1 0 1 0 1 0
2A0000–2AFFFF
SA85
1 0 1 0 1 0 1
550000–55FFFF
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
29
D a t a
S h e e t
Table 11. S29GL064M (Models R1, R2, R8, R9)
Sector Addresses (Sheet 1 of 3)
Sector
30
A21–A15
Sector
Size
(KB/
Kwords)
8-bit
Address
Range
8-bit
Address
Range
000000–007FFF
SA0
0
0
0
0
0
0
0
64/32
000000–00FFFF
SA1
0
0
0
0
0
0
1
64/32
010000–01FFFF
008000–00FFFF
SA2
0
0
0
0
0
1
0
64/32
020000–02FFFF
010000–017FFF
SA3
0
0
0
0
0
1
1
64/32
030000–03FFFF
018000–01FFFF
SA4
0
0
0
0
1
0
0
64/32
040000–04FFFF
020000–027FFF
SA5
0
0
0
0
1
0
1
64/32
050000–05FFFF
028000–02FFFF
SA6
0
0
0
0
1
1
0
64/32
060000–06FFFF
030000–037FFF
SA7
0
0
0
0
1
1
1
64/32
070000–07FFFF
038000–03FFFF
SA8
0
0
0
1
0
0
0
64/32
080000–08FFFF
040000–047FFF
SA9
0
0
0
1
0
0
1
64/32
090000–09FFFF
048000–04FFFF
SA10
0
0
0
1
0
1
0
64/32
0A0000–0AFFFF
050000–057FFF
SA11
0
0
0
1
0
1
1
64/32
0B0000–0BFFFF
058000–05FFFF
SA12
0
0
0
1
1
0
0
64/32
0C0000–0CFFFF
060000–067FFF
SA13
0
0
0
1
1
0
1
64/32
0D0000–0DFFFF
068000–06FFFF
SA14
0
0
0
1
1
1
0
64/32
0E0000–0EFFFF
070000–077FFF
SA15
0
0
0
1
1
1
1
64/32
0F0000–0FFFFF
078000–07FFFF
SA16
0
0
1
0
0
0
0
64/32
100000–10FFFF
080000–087FFF
SA17
0
0
1
0
0
0
1
64/32
110000–11FFFF
088000–08FFFF
SA18
0
0
1
0
0
1
0
64/32
120000–12FFFF
090000–097FFF
SA19
0
0
1
0
0
1
1
64/32
130000–13FFFF
098000–09FFFF
SA20
0
0
1
0
1
0
0
64/32
140000–14FFFF
0A0000–0A7FFF
SA21
0
0
1
0
1
0
1
64/32
150000–15FFFF
0A8000–0AFFFF
SA22
0
0
1
0
1
1
0
64/32
160000–16FFFF
0B0000–0B7FFF
SA23
0
0
1
0
1
1
1
64/32
170000–17FFFF
0B8000–0BFFFF
SA24
0
0
1
1
0
0
0
64/32
180000–18FFFF
0C0000–0C7FFF
SA25
0
0
1
1
0
0
1
64/32
190000–19FFFF
0C8000–0CFFFF
SA26
0
0
1
1
0
1
0
64/32
1A0000–1AFFFF
0D0000–0D7FFF
SA27
0
0
1
1
0
1
1
64/32
1B0000–1BFFFF
0D8000–0DFFFF
SA28
0
0
1
1
1
0
0
64/32
1C0000–1CFFFF
0E0000–0E7FFF
SA29
0
0
1
1
1
0
1
64/32
1D0000–1DFFFF
0E8000–0EFFFF
SA30
0
0
1
1
1
1
0
64/32
1E0000–1EFFFF
0F0000–0F7FFF
SA31
0
0
1
1
1
1
1
64/32
1F0000–1FFFFF
0F8000–0FFFFF
SA32
0
1
0
0
0
0
0
64/32
200000–20FFFF
100000–107FFF
SA33
0
1
0
0
0
0
1
64/32
210000–21FFFF
108000–10FFFF
SA34
0
1
0
0
0
1
0
64/32
220000–22FFFF
110000–117FFF
SA35
0
1
0
0
0
1
1
64/32
230000–23FFFF
118000–11FFFF
SA36
0
1
0
0
1
0
0
64/32
240000–24FFFF
120000–127FFF
SA37
0
1
0
0
1
0
1
64/32
250000–25FFFF
128000–12FFFF
SA38
0
1
0
0
1
1
0
64/32
260000–26FFFF
130000–137FFF
SA39
0
1
0
0
1
1
1
64/32
270000–27FFFF
138000–13FFFF
SA40
0
1
0
1
0
0
0
64/32
280000–28FFFF
140000–147FFF
SA41
0
1
0
1
0
0
1
64/32
290000–29FFFF
148000–14FFFF
SA42
0
1
0
1
0
1
0
64/32
2A0000–2AFFFF
150000–157FFF
SA43
0
1
0
1
0
1
1
64/32
2B0000–2BFFFF
158000–15FFFF
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Table 11. S29GL064M (Models R1, R2, R8, R9)
Sector Addresses (Sheet 2 of 3)
Sector
Sector
Size
(KB/
Kwords)
A21–A15
8-bit
Address
Range
8-bit
Address
Range
SA44
0
1
0
1
1
0
0
64/32
2C0000–2CFFFF
160000–167FFF
SA45
0
1
0
1
1
0
1
64/32
2D0000–2DFFFF
168000–16FFFF
SA46
0
1
0
1
1
1
0
64/32
2E0000–2EFFFF
170000–177FFF
SA47
0
1
0
1
1
1
1
64/32
2F0000–2FFFFF
178000–17FFFF
SA48
0
1
1
0
0
0
0
64/32
300000–30FFFF
180000–187FFF
SA49
0
1
1
0
0
0
1
64/32
310000–31FFFF
188000–18FFFF
SA50
0
1
1
0
0
1
0
64/32
320000–32FFFF
190000–197FFF
SA51
0
1
1
0
0
1
1
64/32
330000–33FFFF
198000–19FFFF
SA52
0
1
1
0
1
0
0
64/32
340000–34FFFF
1A0000–1A7FFF
SA53
0
1
1
0
1
0
1
64/32
350000–35FFFF
1A8000–1AFFFF
SA54
0
1
1
0
1
1
0
64/32
360000–36FFFF
1B0000–1B7FFF
SA55
0
1
1
0
1
1
1
64/32
370000–37FFFF
1B8000–1BFFFF
SA56
0
1
1
1
0
0
0
64/32
380000–38FFFF
1C0000–1C7FFF
SA57
0
1
1
1
0
0
1
64/32
390000–39FFFF
1C8000–1CFFFF
SA58
0
1
1
1
0
1
0
64/32
3A0000–3AFFFF
1D0000–1D7FFF
SA59
0
1
1
1
0
1
1
64/32
3B0000–3BFFFF
1D8000–1DFFFF
SA60
0
1
1
1
1
0
0
64/32
3C0000–3CFFFF
1E0000–1E7FFF
SA61
0
1
1
1
1
0
1
64/32
3D0000–3DFFFF
1E8000–1EFFFF
SA62
0
1
1
1
1
1
0
64/32
3E0000–3EFFFF
1F0000–1F7FFF
SA63
0
1
1
1
1
1
1
64/32
3F0000–3FFFFF
1F8000–1FFFFF
SA64
1
0
0
0
0
0
0
64/32
400000–40FFFF
200000–207FFF
SA65
1
0
0
0
0
0
1
64/32
410000–41FFFF
208000–20FFFF
SA66
1
0
0
0
0
1
0
64/32
420000–42FFFF
210000–217FFF
SA67
1
0
0
0
0
1
1
64/32
430000–43FFFF
218000–21FFFF
SA68
1
0
0
0
1
0
0
64/32
440000–44FFFF
220000–227FFF
SA69
1
0
0
0
1
0
1
64/32
450000–45FFFF
228000–22FFFF
SA70
1
0
0
0
1
1
0
64/32
460000–46FFFF
230000–237FFF
SA71
1
0
0
0
1
1
1
64/32
470000–47FFFF
238000–23FFFF
SA72
1
0
0
1
0
0
0
64/32
480000–48FFFF
240000–247FFF
SA73
1
0
0
1
0
0
1
64/32
490000–49FFFF
248000–24FFFF
SA74
1
0
0
1
0
1
0
64/32
4A0000–4AFFFF
250000–257FFF
SA75
1
0
0
1
0
1
1
64/32
4B0000–4BFFFF
258000–25FFFF
SA76
1
0
0
1
1
0
0
64/32
4C0000–4CFFFF
260000–267FFF
SA77
1
0
0
1
1
0
1
64/32
4D0000–4DFFFF
268000–26FFFF
SA78
1
0
0
1
1
1
0
64/32
4E0000–4EFFFF
270000–277FFF
SA79
1
0
0
1
1
1
1
64/32
4F0000–4FFFFF
278000–27FFFF
SA80
1
0
1
0
0
0
0
64/32
500000–50FFFF
280000–287FFF
SA81
1
0
1
0
0
0
1
64/32
510000–51FFFF
288000–28FFFF
SA82
1
0
1
0
0
1
0
64/32
520000–52FFFF
290000–297FFF
SA83
1
0
1
0
0
1
1
64/32
530000–53FFFF
298000–29FFFF
SA84
1
0
1
0
1
0
0
64/32
540000–54FFFF
2A0000–2A7FFF
SA85
1
0
1
0
1
0
1
64/32
550000–55FFFF
2A8000–2AFFFF
SA86
1
0
1
0
1
1
0
64/32
560000–56FFFF
2B0000–2B7FFF
SA87
1
0
1
0
1
1
1
64/32
570000–57FFFF
2B8000–2BFFFF
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
31
D a t a
S h e e t
Table 11. S29GL064M (Models R1, R2, R8, R9)
Sector Addresses (Sheet 3 of 3)
Sector
32
A21–A15
Sector
Size
(KB/
Kwords)
8-bit
Address
Range
8-bit
Address
Range
SA88
1
0
1
1
0
0
0
64/32
580000–58FFFF
2C0000–2C7FFF
SA89
1
0
1
1
0
0
1
64/32
590000–59FFFF
2C8000–2CFFFF
SA90
1
0
1
1
0
1
0
64/32
5A0000–5AFFFF
2D0000–2D7FFF
SA91
1
0
1
1
0
1
1
64/32
5B0000–5BFFFF
2D8000–2DFFFF
SA92
1
0
1
1
1
0
0
64/32
5C0000–5CFFFF
2E0000–2E7FFF
SA93
1
0
1
1
1
0
1
64/32
5D0000–5DFFFF
2E8000–2EFFFF
SA94
1
0
1
1
1
1
0
64/32
5E0000–5EFFFF
2F0000–2F7FFF
SA95
1
0
1
1
1
1
1
64/32
5F0000–5FFFFF
2F8000–2FFFFF
SA96
1
1
0
0
0
0
0
64/32
600000–60FFFF
300000–307FFF
SA97
1
1
0
0
0
0
1
64/32
610000–61FFFF
308000–30FFFF
SA98
1
1
0
0
0
1
0
64/32
620000–62FFFF
310000–317FFF
SA99
1
1
0
0
0
1
1
64/32
630000–63FFFF
318000–31FFFF
SA100
1
1
0
0
1
0
0
64/32
640000–64FFFF
320000–327FFF
SA101
1
1
0
0
1
0
1
64/32
650000–65FFFF
328000–32FFFF
SA102
1
1
0
0
1
1
0
64/32
660000–66FFFF
330000–337FFF
SA103
1
1
0
0
1
1
1
64/32
670000–67FFFF
338000–33FFFF
SA104
1
1
0
1
0
0
0
64/32
680000–68FFFF
340000–347FFF
SA105
1
1
0
1
0
0
1
64/32
690000–69FFFF
348000–34FFFF
SA106
1
1
0
1
0
1
0
64/32
6A0000–6AFFFF
350000–357FFF
SA107
1
1
0
1
0
1
1
64/32
6B0000–6BFFFF
358000–35FFFF
SA108
1
1
0
1
1
0
0
64/32
6C0000–6CFFFF
360000–367FFF
SA109
1
1
0
1
1
0
1
64/32
6D0000–6DFFFF
368000–36FFFF
SA110
1
1
0
1
1
1
0
64/32
6E0000–6EFFFF
370000–377FFF
SA111
1
1
0
1
1
1
1
64/32
6F0000–6FFFFF
378000–37FFFF
SA112
1
1
1
0
0
0
0
64/32
700000–70FFFF
380000–387FFF
SA113
1
1
1
0
0
0
1
64/32
710000–71FFFF
388000–38FFFF
SA114
1
1
1
0
0
1
0
64/32
720000–72FFFF
390000–397FFF
SA115
1
1
1
0
0
1
1
64/32
730000–73FFFF
398000–39FFFF
SA116
1
1
1
0
1
0
0
64/32
740000–74FFFF
3A0000–3A7FFF
SA117
1
1
1
0
1
0
1
64/32
750000–75FFFF
3A8000–3AFFFF
SA118
1
1
1
0
1
1
0
64/32
760000–76FFFF
3B0000–3B7FFF
SA119
1
1
1
0
1
1
1
64/32
770000–77FFFF
3B8000–3BFFFF
SA120
1
1
1
1
0
0
0
64/32
780000–78FFFF
3C0000–3C7FFF
SA121
1
1
1
1
0
0
1
64/32
790000–79FFFF
3C8000–3CFFFF
SA122
1
1
1
1
0
1
0
64/32
7A0000–7AFFFF
3D0000–3D7FFF
SA123
1
1
1
1
0
1
1
64/32
7B0000–7BFFFF
3D8000–3DFFFF
SA124
1
1
1
1
1
0
0
64/32
7C0000–7CFFFF
3E0000–3E7FFF
SA125
1
1
1
1
1
0
1
64/32
7D0000–7DFFFF
3E8000–3EFFFF
SA126
1
1
1
1
1
1
0
64/32
7E0000–7EFFFF
3F0000–3F7FFF
SA127
1
1
1
1
1
1
1
64/32
7F0000–7FFFFF
3F8000–3FFFFF
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
A21–A12
Sector
Size*
S29GL064M (Model R3) Top Boot Sector Addresses (Sheet 1 of 2)
8-bit
Address
Range
16-bit
Address
Range
Sector
Sector
Table 12.
S h e e t
A21–A12
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
SA0
0000000xxx 64/32
000000h–00FFFFh
00000h–07FFFh
SA45
0101101xxx
64/32
2D0000h–2DFFFFh 168000h–16FFFFh
SA1
0000001xxx 64/32
010000h–01FFFFh
08000h–0FFFFh
SA46
0101110xxx
64/32
2E0000h–2EFFFFh 170000h–177FFFh
SA2
0000010xxx 64/32
020000h–02FFFFh
10000h–17FFFh
SA47
0101111xxx
64/32
2F0000h–2FFFFFh
SA3
0000011xxx 64/32
030000h–03FFFFh
18000h–1FFFFh
SA48
0110000xxx
64/32
300000h–30FFFFh 180000h–187FFFh
SA4
0000100xxx 64/32
040000h–04FFFFh
20000h–27FFFh
SA49
0110001xxx
64/32
310000h–31FFFFh 188000h–18FFFFh
SA5
0000101xxx 64/32
050000h–05FFFFh
28000h–2FFFFh
SA50
0110010xxx
64/32
320000h–32FFFFh 190000h–197FFFh
SA6
0000110xxx 64/32
060000h–06FFFFh
30000h–37FFFh
SA51
0110011xxx
64/32
330000h–33FFFFh 198000h–19FFFFh
SA7
0000111xxx 64/32
070000h–07FFFFh
38000h–3FFFFh
SA52
0100100xxx
64/32
340000h–34FFFFh 1A0000h–1A7FFFh
SA8
0001000xxx 64/32
080000h–08FFFFh
40000h–47FFFh
SA53
0110101xxx
64/32
350000h–35FFFFh 1A8000h–1AFFFFh
SA9
0001001xxx 64/32
090000h–09FFFFh
48000h–4FFFFh
SA54
0110110xxx
64/32
360000h–36FFFFh 1B0000h–1B7FFFh
SA10
0001010xxx 64/32 0A0000h–0AFFFFh
50000h–57FFFh
SA55
0110111xxx
64/32
370000h–37FFFFh 1B8000h–1BFFFFh
SA11
0001011xxx 64/32 0B0000h–0BFFFFh
58000h–5FFFFh
SA56
0111000xxx
64/32
380000h–38FFFFh 1C0000h–1C7FFFh
SA12
0001100xxx 64/32 0C0000h–0CFFFFh
60000h–67FFFh
SA57
0111001xxx
64/32
390000h–39FFFFh 1C8000h–1CFFFFh
SA13
0001101xxx 64/32 0D0000h–0DFFFFh
68000h–6FFFFh
SA58
0111010xxx
64/32
3A0000h–3AFFFFh 1D0000h–1D7FFFh
SA14
0001101xxx 64/32
70000h–77FFFh
SA59
0111011xxx
64/32
3B0000h–3BFFFFh 1D8000h–1DFFFFh
SA15
0001111xxx 64/32
0F0000h–0FFFFFh
78000h–7FFFFh
SA60
0111100xxx
64/32
3C0000h–3CFFFFh 1E0000h–1E7FFFh
SA16
0010000xxx 64/32
100000h–00FFFFh
80000h–87FFFh
SA61
0111101xxx
64/32
3D0000h–3DFFFFh 1E8000h–1EFFFFh
SA17
0010001xxx 64/32
110000h–11FFFFh
88000h–8FFFFh
SA62
0111110xxx
64/32
3E0000h–3EFFFFh
1F0000h–1F7FFFh
1F8000h–1FFFFFh
0E0000h–0EFFFFh
178000h–17FFFFh
SA18
0010010xxx 64/32
120000h–12FFFFh
90000h–97FFFh
SA63
0111111xxx
64/32
3F0000h–3FFFFFh
SA19
0010011xxx 64/32
130000h–13FFFFh
98000h–9FFFFh
SA64
1000000xxx
64/32
400000h–40FFFFh 200000h–207FFFh
SA20
0010100xxx 64/32
140000h–14FFFFh
A0000h–A7FFFh
SA65
1000001xxx
64/32
410000h–41FFFFh 208000h–20FFFFh
SA21
0010101xxx 64/32
150000h–15FFFFh
A8000h–AFFFFh
SA66
1000010xxx
64/32
420000h–42FFFFh 210000h–217FFFh
SA22
0010110xxx 64/32
160000h–16FFFFh
B0000h–B7FFFh
SA67
1000011xxx
64/32
430000h–43FFFFh 218000h–21FFFFh
440000h–44FFFFh 220000h–227FFFh
SA23
0010111xxx 64/32
170000h–17FFFFh
B8000h–BFFFFh
SA68
1000100xxx
64/32
SA24
0011000xxx 64/32
180000h–18FFFFh
C0000h–C7FFFh
SA69
1000101xxx
64/32
450000h–45FFFFh 228000h–22FFFFh
SA25
0011001xxx 64/32
190000h–19FFFFh
C8000h–CFFFFh
SA70
1000110xxx
64/32
460000h–46FFFFh 230000h–237FFFh
SA26
0011010xxx 64/32 1A0000h–1AFFFFh
D0000h–D7FFFh
SA71
1000111xxx
64/32
470000h–47FFFFh 238000h–23FFFFh
SA27
0011011xxx 64/32 1B0000h–1BFFFFh
D8000h–DFFFFh
SA72
1001000xxx
64/32
480000h–48FFFFh 240000h–247FFFh
SA28
0011000xxx 64/32 1C0000h–1CFFFFh
E0000h–E7FFFh
SA73
1001001xxx
64/32
490000h–49FFFFh 248000h–24FFFFh
SA29
0011101xxx 64/32 1D0000h–1DFFFFh
E8000h–EFFFFh
SA74
1001010xxx
64/32
4A0000h–4AFFFFh 250000h–257FFFh
SA30
0011110xxx 64/32
F0000h–F7FFFh
SA75
1001011xxx
64/32
4B0000h–4BFFFFh 258000h–25FFFFh
SA31
0011111xxx 64/32
1F0000h–1FFFFFh
F8000h–FFFFFh
SA76
1001100xxx
64/32
4C0000h–4CFFFFh 260000h–267FFFh
SA32
0100000xxx 64/32
200000h–20FFFFh
F9000h–107FFFh
SA77
1001101xxx
64/32
4D0000h–4DFFFFh 268000h–26FFFFh
SA33
0100001xxx 64/32
210000h–21FFFFh 108000h–10FFFFh
SA78
1001110xxx
64/32
4E0000h–4EFFFFh 270000h–277FFFh
SA34
0100010xxx 64/32
220000h–22FFFFh 110000h–117FFFh
SA79
1001111xxx
64/32
4F0000h–4FFFFFh
SA35
0101011xxx 64/32
230000h–23FFFFh 118000h–11FFFFh
SA80
1010000xxx
64/32
500000h–50FFFFh 280000h–28FFFFh
SA36
0100100xxx 64/32
240000h–24FFFFh 120000h–127FFFh
SA81
1010001xxx
64/32
510000h–51FFFFh 288000h–28FFFFh
SA37
0100101xxx 64/32
250000h–25FFFFh 128000h–12FFFFh
SA82
1010010xxx
64/32
520000h–52FFFFh 290000h–297FFFh
SA38
0100110xxx 64/32
260000h–26FFFFh 130000h–137FFFh
SA83
1010011xxx
64/32
530000h–53FFFFh 298000h–29FFFFh
SA39
0100111xxx 64/32
270000h–27FFFFh 138000h–13FFFFh
SA84
1010100xxx
64/32
540000h–54FFFFh 2A0000h–2A7FFFh
SA40
0101000xxx 64/32
280000h–28FFFFh 140000h–147FFFh
SA85
1010101xxx
64/32
550000h–55FFFFh 2A8000h–2AFFFFh
SA41
0101001xxx 64/32
290000h–29FFFFh 148000h–14FFFFh
SA86
1010110xxx
64/32
560000h–56FFFFh 2B0000h–2B7FFFh
1E0000h–1EFFFFh
278000h–27FFFFh
SA42
0101010xxx 64/32 2A0000h–2AFFFFh 150000h–157FFFh
SA87
1010111xxx
64/32
570000h–57FFFFh 2B8000h–2BFFFFh
SA43
0101011xxx 64/32 2B0000h–2BFFFFh 158000h–15FFFFh
SA88
1011000xxx
64/32
580000h–58FFFFh 2C0000h–2C7FFFh
SA44
0101100xxx 64/32 2C0000h–2CFFFFh 160000h–167FFFh
SA89
1011001xxx
64/32
590000h–59FFFFh 2C8000h–2CFFFFh
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
33
D a t a
A21–A12
Sector
Size*
S29GL064M (Model R3) Top Boot Sector Addresses (Sheet 2 of 2)
8-bit
Address
Range
16-bit
Address
Range
Sector
Sector
Table 12.
S h e e t
A21–A12
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
SA90
1011010xxx 64/32 5A0000h–5AFFFFh 2D0000h–2D7FFFh
SA113
1110001xxx
64/32
710000h–71FFFFh 388000h–38FFFFh
SA91
1011011xxx 64/32 5B0000h–5BFFFFh 2D8000h–2DFFFFh
SA114
1110010xxx
64/32
720000h–72FFFFh 390000h–397FFFh
SA92
1011100xxx 64/32 5C0000h–5CFFFFh 2E0000h–2E7FFFh
SA115
1110011xxx
64/32
730000h–73FFFFh 398000h–39FFFFh
SA93
1011101xxx 64/32 5D0000h–5DFFFFh 2E8000h–2EFFFFh
SA116
1110100xxx
64/32
740000h–74FFFFh 3A0000h–3A7FFFh
SA94
1011110xxx 64/32
5E0000h–5EFFFFh
2F0000h–2FFFFFh
SA117
1110101xxx
64/32
750000h–75FFFFh 3A8000h–3AFFFFh
SA95
1011111xxx 64/32
5F0000h–5FFFFFh
2F8000h–2FFFFFh
SA118
1110110xxx
64/32
760000h–76FFFFh 3B0000h–3B7FFFh
SA96
1100000xxx 64/32
600000h–60FFFFh 300000h–307FFFh
SA119
1110111xxx
64/32
770000h–77FFFFh 3B8000h–3BFFFFh
SA97
1100001xxx 64/32
610000h–61FFFFh 308000h–30FFFFh
SA120
1111000xxx
64/32
780000h–78FFFFh 3C0000h–3C7FFFh
SA98
1100010xxx 64/32
620000h–62FFFFh 310000h–317FFFh
SA121
1111001xxx
64/32
790000h–79FFFFh 3C8000h–3CFFFFh
SA99
1100011xxx 64/32
630000h–63FFFFh 318000h–31FFFFh
SA122
1111010xxx
64/32
7A0000h–7AFFFFh 3D0000h–3D7FFFh
SA100 1100100xxx 64/32
640000h–64FFFFh 320000h–327FFFh
SA123
1111011xxx
64/32
7B0000h–7BFFFFh 3D8000h–3DFFFFh
SA101 1100101xxx 64/32
650000h–65FFFFh 328000h–32FFFFh
SA124
1111100xxx
64/32
7C0000h–7CFFFFh 3E0000h–3E7FFFh
SA102 1100110xxx 64/32
660000h–66FFFFh 330000h–337FFFh
SA125
1111101xxx
64/32
7D0000h–7DFFFFh 3E8000h–3EFFFFh
SA103 1100111xxx 64/32
670000h–67FFFFh 338000h–33FFFFh
SA126
1111110xxx
64/32
7E0000h–7EFFFFh
SA104 1101000xxx 64/32
680000h–68FFFFh 340000h–347FFFh
SA127
1111111000
8/4
7F0000h–7F1FFFh
3F8000h–3F8FFFh
SA105 1101001xxx 64/32
690000h–69FFFFh 348000h–34FFFFh
SA128
1111111001
8/4
7F2000h–7F3FFFh
3F9000h–3F9FFFh
SA106 1101010xxx 64/32 6A0000h–6AFFFFh 350000h–357FFFh
SA129
1111111010
8/4
7F4000h–7F5FFFh
3FA000h–3FAFFFh
SA107 1101011xxx 64/32 6B0000h–6BFFFFh 358000h–35FFFFh
SA130
1111111011
8/4
7F6000h–7F7FFFh 3FB000h–3FBFFFh
SA108 1101100xxx 64/32 6C0000h–6CFFFFh 360000h–367FFFh
SA131
1111111100
8/4
7F8000h–7F9FFFh 3FC000h–3FCFFFh
SA109 1101101xxx 64/32 6D0000h–6DFFFFh 368000h–36FFFFh
SA132
1111111101
8/4
7FA000h–7FBFFFh 3FD000h–3FDFFFh
SA110 1101110xxx 64/32
6E0000h–6EFFFFh 370000h–377FFFh
SA133
1111111110
8/4
7FC000h–7FDFFFh 3FE000h–3FEFFFh
SA111 1101111xxx 64/32
6F0000h–6FFFFFh
SA134
1111111111
8/4
7FE000h–7FFFFFh
SA112 1110000xxx 64/32
700000h–70FFFFh 380000h–387FFFh
378000h–37FFFFh
3F0000h–3F7FFFh
3FF000h–3FFFFFh
* Sector sizes are given in Kbytes/Kwords.
34
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
A21–A12
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
Sector
Sector
Table 13. S29GL064M (Model R4) Bottom Boot Sector Addresses (Sheet 1 of 2)
A21–A12
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
SA0
0000000000
8/4
000000h–001FFFh
00000h–00FFFh
SA45
0100110xxx
64/32
260000h–26FFFFh
130000h–137FFFh
SA1
0000000001
8/4
002000h–003FFFh
01000h–01FFFh
SA46
0100111xxx
64/32
270000h–27FFFFh
138000h–13FFFFh
SA2
0000000010
8/4
004000h–005FFFh
02000h–02FFFh
SA47
0101000xxx
64/32
280000h–28FFFFh
140000h–147FFFh
SA3
0000000011
8/4
006000h–007FFFh
03000h–03FFFh
SA48
0101001xxx
64/32
290000h–29FFFFh
148000h–14FFFFh
SA4
0000000100
8/4
008000h–009FFFh
04000h–04FFFh
SA49
0101010xxx
64/32
2A0000h–2AFFFFh
150000h–157FFFh
SA5
0000000101
8/4
00A000h–00BFFFh
05000h–05FFFh
SA50
0101011xxx
64/32
2B0000h–2BFFFFh
158000h–15FFFFh
SA6
0000000110
8/4
00C000h–00DFFFh
06000h–06FFFh
SA51
0101100xxx
64/32
2C0000h–2CFFFFh
160000h–167FFFh
SA7
0000000111
8/4
00E000h–00FFFFFh
07000h–07FFFh
SA52
0101101xxx
64/32
2D0000h–2DFFFFh
168000h–16FFFFh
SA8
0000001xxx
64/32
010000h–01FFFFh
08000h–0FFFFh
SA53
0101110xxx
64/32
2E0000h–2EFFFFh
170000h–177FFFh
SA9
0000010xxx
64/32
020000h–02FFFFh
10000h–17FFFh
SA54
0101111xxx
64/32
2F0000h–2FFFFFh
178000h–17FFFFh
SA10
0000011xxx
64/32
030000h–03FFFFh
18000h–1FFFFh
SA55
0110000xxx
64/32
300000h–30FFFFh
180000h–187FFFh
SA11
0000100xxx
64/32
040000h–04FFFFh
20000h–27FFFh
SA56
0110001xxx
64/32
310000h–31FFFFh
188000h–18FFFFh
190000h–197FFFh
SA12
0000101xxx
64/32
050000h–05FFFFh
28000h–2FFFFh
SA57
0110010xxx
64/32
320000h–32FFFFh
SA13
0000110xxx
64/32
060000h–06FFFFh
30000h–37FFFh
SA58
0110011xxx
64/32
330000h–33FFFFh
198000h–19FFFFh
SA14
0000111xxx
64/32
070000h–07FFFFh
38000h–3FFFFh
SA59
0100100xxx
64/32
340000h–34FFFFh
1A0000h–1A7FFFh
SA15
0001000xxx
64/32
080000h–08FFFFh
40000h–47FFFh
SA60
0110101xxx
64/32
350000h–35FFFFh
1A8000h–1AFFFFh
SA16
0001001xxx
64/32
090000h–09FFFFh
48000h–4FFFFh
SA61
0110110xxx
64/32
360000h–36FFFFh
1B0000h–1B7FFFh
SA17
0001010xxx
64/32
0A0000h–0AFFFFh
50000h–57FFFh
SA62
0110111xxx
64/32
370000h–37FFFFh
1B8000h–1BFFFFh
SA18
0001011xxx
64/32
0B0000h–0BFFFFh
58000h–5FFFFh
SA63
0111000xxx
64/32
380000h–38FFFFh
1C0000h–1C7FFFh
SA19
0001100xxx
64/32
0C0000h–0CFFFFh
60000h–67FFFh
SA64
0111001xxx
64/32
390000h–39FFFFh
1C8000h–1CFFFFh
SA20
0001101xxx
64/32
0D0000h–0DFFFFh
68000h–6FFFFh
SA65
0111010xxx
64/32
3A0000h–3AFFFFh
1D0000h–1D7FFFh
SA21
0001101xxx
64/32
0E0000h–0EFFFFh
70000h–77FFFh
SA66
0111011xxx
64/32
3B0000h–3BFFFFh
1D8000h–1DFFFFh
SA22
0001111xxx
64/32
0F0000h–0FFFFFh
78000h–7FFFFh
SA67
0111100xxx
64/32
3C0000h–3CFFFFh
1E0000h–1E7FFFh
SA23
0010000xxx
64/32
100000h–00FFFFh
80000h–87FFFh
SA68
0111101xxx
64/32
3D0000h–3DFFFFh
1E8000h–1EFFFFh
SA24
0010001xxx
64/32
110000h–11FFFFh
88000h–8FFFFh
SA69
0111110xxx
64/32
3E0000h–3EFFFFh
1F0000h–1F7FFFh
SA25
0010010xxx
64/32
120000h–12FFFFh
90000h–97FFFh
SA70
0111111xxx
64/32
3F0000h–3FFFFFh
1F8000h–1FFFFFh
SA26
0010011xxx
64/32
130000h–13FFFFh
98000h–9FFFFh
SA71
1000000xxx
64/32
400000h–40FFFFh
200000h–207FFFh
SA27
0010100xxx
64/32
140000h–14FFFFh
A0000h–A7FFFh
SA72
1000001xxx
64/32
410000h–41FFFFh
208000h–20FFFFh
SA28
0010101xxx
64/32
150000h–15FFFFh
A8000h–AFFFFh
SA73
1000010xxx
64/32
420000h–42FFFFh
210000h–217FFFh
SA29
0010110xxx
64/32
160000h–16FFFFh
B0000h–B7FFFh
SA74
1000011xxx
64/32
430000h–43FFFFh
218000h–21FFFFh
SA30
0010111xxx
64/32
170000h–17FFFFh
B8000h–BFFFFh
SA75
1000100xxx
64/32
440000h–44FFFFh
220000h–227FFFh
SA31
0011000xxx
64/32
180000h–18FFFFh
C0000h–C7FFFh
SA76
1000101xxx
64/32
450000h–45FFFFh
228000h–22FFFFh
SA32
0011001xxx
64/32
190000h–19FFFFh
C8000h–CFFFFh
SA77
1000110xxx
64/32
460000h–46FFFFh
230000h–237FFFh
SA33
0011010xxx
64/32
1A0000h–1AFFFFh
D0000h–D7FFFh
SA78
1000111xxx
64/32
470000h–47FFFFh
238000h–23FFFFh
SA34
0011011xxx
64/32
1B0000h–1BFFFFh
D8000h–DFFFFh
SA79
1001000xxx
64/32
480000h–48FFFFh
240000h–247FFFh
SA35
0011000xxx
64/32
1C0000h–1CFFFFh
E0000h–E7FFFh
SA80
1001001xxx
64/32
490000h–49FFFFh
248000h–24FFFFh
SA36
0011101xxx
64/32
1D0000h–1DFFFFh
E8000h–EFFFFh
SA81
1001010xxx
64/32
4A0000h–4AFFFFh
250000h–257FFFh
SA37
0011110xxx
64/32
1E0000h–1EFFFFh
F0000h–F7FFFh
SA82
1001011xxx
64/32
4B0000h–4BFFFFh
258000h–25FFFFh
SA38
0011111xxx
64/32
1F0000h–1FFFFFh
F8000h–FFFFFh
SA83
1001100xxx
64/32
4C0000h–4CFFFFh
260000h–267FFFh
SA39
0100000xxx
64/32
200000h–20FFFFh
F9000h–107FFFh
SA84
1001101xxx
64/32
4D0000h–4DFFFFh
268000h–26FFFFh
SA40
0100001xxx
64/32
210000h–21FFFFh
108000h–10FFFFh
SA85
1001110xxx
64/32
4E0000h–4EFFFFh
270000h–277FFFh
SA41
0100010xxx
64/32
220000h–22FFFFh
110000h–117FFFh
SA86
1001111xxx
64/32
4F0000h–4FFFFFh
278000h–27FFFFh
SA42
0101011xxx
64/32
230000h–23FFFFh
118000h–11FFFFh
SA87
1010000xxx
64/32
500000h–50FFFFh
280000h–28FFFFh
SA43
0100100xxx
64/32
240000h–24FFFFh
120000h–127FFFh
SA88
1010001xxx
64/32
510000h–51FFFFh
288000h–28FFFFh
SA44
0100101xxx
64/32
250000h–25FFFFh
128000h–12FFFFh
SA89
1010010xxx
64/32
520000h–52FFFFh
290000h–297FFFh
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
35
D a t a
S29GL064M (Model R4) Bottom Boot Sector Addresses (Sheet 2 of 2)
A21–A12
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
SA90
1010011xxx
64/32
SA91
1010100xxx
64/32
530000h–53FFFFh
298000h–29FFFFh
540000h–54FFFFh
2A0000h–2A7FFFh
SA92
1010101xxx
64/32
550000h–55FFFFh
SA93
SA94
1010110xxx
64/32
1010111xxx
64/32
SA95
1011000xxx
64/32
SA96
1011001xxx
64/32
SA97
1011010xxx
64/32
SA98
1011011xxx
64/32
5B0000h–5BFFFFh
2D8000h–2DFFFFh
SA121
1110010xxx
SA99
1011100xxx
64/32
5C0000h–5CFFFFh
2E0000h–2E7FFFh
SA122
1110011xxx
SA100
1011101xxx
64/32
5D0000h–5DFFFFh
2E8000h–2EFFFFh
SA123
1110100xxx
SA101
1011110xxx
64/32
5E0000h–5EFFFFh
2F0000h–2FFFFFh
SA124
SA102
1011111xxx
64/32
5F0000h–5FFFFFh
2F8000h–2FFFFFh
SA125
SA103
1100000xxx
64/32
600000h–60FFFFh
300000h–307FFFh
SA104
1100001xxx
64/32
610000h–61FFFFh
SA105
1100010xxx
64/32
620000h–62FFFFh
SA106
1100011xxx
64/32
630000h–63FFFFh
SA107
1100100xxx
64/32
640000h–64FFFFh
SA108
1100101xxx
64/32
650000h–65FFFFh
328000h–32FFFFh
Sector
Sector
Table 13.
S h e e t
A21–A12
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
SA113
1101010xxx
64/32
6A0000h–6AFFFFh
350000h–357FFFh
SA114
1101011xxx
64/32
6B0000h–6BFFFFh
358000h–35FFFFh
2A8000h–2AFFFFh
SA115
1101100xxx
64/32
6C0000h–6CFFFFh
360000h–367FFFh
560000h–56FFFFh
2B0000h–2B7FFFh
SA116
1101101xxx
64/32
6D0000h–6DFFFFh
368000h–36FFFFh
570000h–57FFFFh
2B8000h–2BFFFFh
SA117
1101110xxx
64/32
6E0000h–6EFFFFh
370000h–377FFFh
580000h–58FFFFh
2C0000h–2C7FFFh
SA118
1101111xxx
64/32
6F0000h–6FFFFFh
378000h–37FFFFh
590000h–59FFFFh
2C8000h–2CFFFFh
SA119
1110000xxx
64/32
700000h–70FFFFh
380000h–387FFFh
5A0000h–5AFFFFh
2D0000h–2D7FFFh
SA120
1110001xxx
64/32
710000h–71FFFFh
388000h–38FFFFh
64/32
720000h–72FFFFh
390000h–397FFFh
64/32
730000h–73FFFFh
398000h–39FFFFh
64/32
740000h–74FFFFh
3A0000h–3A7FFFh
1110101xxx
64/32
750000h–75FFFFh
3A8000h–3AFFFFh
1110110xxx
64/32
760000h–76FFFFh
3B0000h–3B7FFFh
SA126
1110111xxx
64/32
770000h–77FFFFh
3B8000h–3BFFFFh
308000h–30FFFFh
SA127
1111000xxx
64/32
780000h–78FFFFh
3C0000h–3C7FFFh
310000h–317FFFh
SA128
1111001xxx
64/32
790000h–79FFFFh
3C8000h–3CFFFFh
318000h–31FFFFh
SA129
1111010xxx
64/32
7A0000h–7AFFFFh
3D0000h–3D7FFFh
320000h–327FFFh
SA130
1111011xxx
64/32
7B0000h–7BFFFFh
3D8000h–3DFFFFh
SA131
1111100xxx
64/32
7C0000h–7CFFFFh
3E0000h–3E7FFFh
SA109
1100110xxx
64/32
660000h–66FFFFh
330000h–337FFFh
SA132
1111101xxx
64/32
7D0000h–7DFFFFh
3E8000h–3EFFFFh
SA110
1100111xxx
64/32
670000h–67FFFFh
338000h–33FFFFh
SA133
1111110xxx
64/32
7E0000h–7EFFFFh
3F0000h–3F7FFFh
SA111
1101000xxx
64/32
680000h–68FFFFh
340000h–347FFFh
SA134
1111111000
64/32
7F0000h–7FFFFFh
3F8000h–3FFFFFh
SA112
1101001xxx
64/32
690000h–69FFFFh
348000h–34FFFFh
* Sector sizes are given in Kbytes/Kwords.
36
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S29GL064M (Model R5, R6, R7) Sector Addresses
16-bit
Address
Range
A21–A15
16-bit
Address
Range
SA0
0 0 0 0 0 0 0
000000–007FFF
SA43 0 1 0 1 0 1 1
158000–15FFFF
SA1
0 0 0 0 0 0 1
008000–00FFFF
SA44 0 1 0 1 1 0 0
160000–167FFF
SA86
1 0 1 0 1 1 0
2B0000–2B7FFF
SA87
1 0 1 0 1 1 1
2B8000–2BFFFF
SA2
0 0 0 0 0 1 0
010000–017FFF
SA45 0 1 0 1 1 0 1
168000–16FFFF
SA3
0 0 0 0 0 1 1
018000–01FFFF
SA46 0 1 0 1 1 1 0
170000–177FFF
SA88
1 0 1 1 0 0 0
2C0000–2C7FFF
SA89
1 0 1 1 0 0 1
SA4
0 0 0 0 1 0 0
020000–027FFF
SA47 0 1 0 1 1 1 1
178000–17FFFF
SA90
2C8000–2CFFFF
1 0 1 1 0 1 0
2D0000–2D7FFF
SA5
0 0 0 0 1 0 1
028000–02FFFF
SA48 0 1 1 0 0 0 0
180000–187FFF
SA6
0 0 0 0 1 1 0
030000–037FFF
SA49 0 1 1 0 0 0 1
188000–18FFFF
SA91
1 0 1 1 0 1 1
2D8000–2DFFFF
SA92
1 0 1 1 1 0 0
SA7
0 0 0 0 1 1 1
038000–03FFFF
SA50 0 1 1 0 0 1 0
190000–197FFF
SA93
2E0000–2E7FFF
1 0 1 1 1 0 1
2E8000–2EFFFF
SA8
0 0 0 1 0 0 0
040000–047FFF
SA51 0 1 1 0 0 1 1
198000–19FFFF
SA9
0 0 0 1 0 0 1
048000–04FFFF
SA52 0 1 1 0 1 0 0
1A0000–1A7FFF
SA94
1 0 1 1 1 1 0
2F0000–2F7FFF
SA95
1 0 1 1 1 1 1
2F8000–2FFFFF
SA10 0 0 0 1 0 1 0
050000–057FFF
SA53 0 1 1 0 1 0 1
1A8000–1AFFFF
SA11 0 0 0 1 0 1 1
058000–05FFFF
SA54 0 1 1 0 1 1 0
1B0000–1B7FFF
SA96
1 1 0 0 0 0 0
300000–307FFF
SA97
1 1 0 0 0 0 1
SA12 0 0 0 1 1 0 0
060000–067FFF
SA55 0 1 1 0 1 1 1
1B8000–1BFFFF
308000–30FFFF
SA98
1 1 0 0 0 1 0
310000–317FFF
SA13 0 0 0 1 1 0 1
068000–06FFFF
SA56 0 1 1 1 0 0 0
SA14 0 0 0 1 1 1 0
070000–077FFF
SA57 0 1 1 1 0 0 1
1C0000–1C7FFF
SA99
1 1 0 0 0 1 1
318000–31FFFF
1C8000–1CFFFF
SA100
1 1 0 0 1 0 0
320000–327FFF
SA15 0 0 0 1 1 1 1
078000–07FFFF
SA58 0 1 1 1 0 1 0
1D0000–1D7FFF
SA101
1 1 0 0 1 0 1
328000–32FFFF
SA16 0 0 1 0 0 0 0
SA17 0 0 1 0 0 0 1
080000–087FFF
SA59 0 1 1 1 0 1 1
1D8000–1DFFFF
SA102
1 1 0 0 1 1 0
330000–337FFF
088000–08FFFF
SA60 0 1 1 1 1 0 0
1E0000–1E7FFF
SA103
1 1 0 0 1 1 1
338000–33FFFF
SA18 0 0 1 0 0 1 0
SA19 0 0 1 0 0 1 1
090000–097FFF
SA61 0 1 1 1 1 0 1
1E8000–1EFFFF
SA104
1 1 0 1 0 0 0
340000–347FFF
098000–09FFFF
SA62 0 1 1 1 1 1 0
1F0000–1F7FFF
SA105
1 1 0 1 0 0 1
SA20 0 0 1 0 1 0 0
348000–34FFFF
0A0000–0A7FFF
SA63 0 1 1 1 1 1 1
1F8000–1FFFFF
SA106
1 1 0 1 0 1 0
350000–357FFF
SA21 0 0 1 0 1 0 1
0A8000–0AFFFF
SA64 1 0 0 0 0 0 0
200000–207FFF
SA107
1 1 0 1 0 1 1
358000–35FFFF
SA22 0 0 1 0 1 1 0
0B0000–0B7FFF
SA65 1 0 0 0 0 0 1
208000–20FFFF
SA108
1 1 0 1 1 0 0
360000–367FFF
SA23 0 0 1 0 1 1 1
0B8000–0BFFFF
SA66 1 0 0 0 0 1 0
210000–217FFF
SA109
1 1 0 1 1 0 1
368000–36FFFF
SA24 0 0 1 1 0 0 0
0C0000–0C7FFF
SA67 1 0 0 0 0 1 1
218000–21FFFF
SA110
1 1 0 1 1 1 0
370000–377FFF
SA25 0 0 1 1 0 0 1
0C8000–0CFFFF
SA68 1 0 0 0 1 0 0
220000–227FFF
SA111
1 1 0 1 1 1 1
378000–37FFFF
SA26 0 0 1 1 0 1 0
0D0000–0D7FFF
SA69 1 0 0 0 1 0 1
228000–22FFFF
SA112
1 1 1 0 0 0 0
380000–387FFF
SA27 0 0 1 1 0 1 1
0D8000–0DFFFF
SA70 1 0 0 0 1 1 0
230000–237FFF
SA113
1 1 1 0 0 0 1
388000–38FFFF
SA28 0 0 1 1 1 0 0
0E0000–0E7FFF
SA71 1 0 0 0 1 1 1
238000–23FFFF
SA114
1 1 1 0 0 1 0
390000–397FFF
SA29 0 0 1 1 1 0 1
0E8000–0EFFFF
SA72 1 0 0 1 0 0 0
240000–247FFF
SA115
1 1 1 0 0 1 1
398000–39FFFF
SA30 0 0 1 1 1 1 0
0F0000–0F7FFF
SA73 1 0 0 1 0 0 1
248000–24FFFF
SA116
1 1 1 0 1 0 0
3A0000–3A7FFF
SA31 0 0 1 1 1 1 1
0F8000–0FFFFF
SA74 1 0 0 1 0 1 0
250000–257FFF
SA117
1 1 1 0 1 0 1
3A8000–3AFFFF
SA32 0 1 0 0 0 0 0
100000–107FFF
SA75 1 0 0 1 0 1 1
258000–25FFFF
SA118
1 1 1 0 1 1 0
3B0000–3B7FFF
SA33 0 1 0 0 0 0 1
108000–10FFFF
SA76 1 0 0 1 1 0 0
260000–267FFF
SA119
1 1 1 0 1 1 1
3B8000–3BFFFF
SA34 0 1 0 0 0 1 0
110000–117FFF
SA77 1 0 0 1 1 0 1
268000–26FFFF
SA120
1 1 1 1 0 0 0
3C0000–3C7FFF
SA35 0 1 0 0 0 1 1
118000–11FFFF
SA78 1 0 0 1 1 1 0
270000–277FFF
SA121
1 1 1 1 0 0 1
3C8000–3CFFFF
SA36 0 1 0 0 1 0 0
120000–127FFF
SA79 1 0 0 1 1 1 1
278000–27FFFF
SA122
1 1 1 1 0 1 0
3D0000–3D7FFF
SA37 0 1 0 0 1 0 1
128000–12FFFF
SA80 1 0 1 0 0 0 0
280000–287FFF
SA123
1 1 1 1 0 1 1
3D8000–3DFFFF
SA38 0 1 0 0 1 1 0
130000–137FFF
SA81 1 0 1 0 0 0 1
288000–28FFFF
SA124
1 1 1 1 1 0 0
3E0000–3E7FFF
SA39 0 1 0 0 1 1 1
138000–13FFFF
SA82 1 0 1 0 0 1 0
290000–297FFF
SA125
1 1 1 1 1 0 1
3E8000–3EFFFF
SA40 0 1 0 1 0 0 0
140000–147FFF
SA83 1 0 1 0 0 1 1
298000–29FFFF
SA126
1 1 1 1 1 1 0
3F0000–3F7FFF
SA41 0 1 0 1 0 0 1
148000–14FFFF
SA84 1 0 1 0 1 0 0
2A0000–2A7FFF
SA127
1 1 1 1 1 1 1
3F8000–3FFFFF
SA42 0 1 0 1 0 1 0
150000–157FFF
SA85 1 0 1 0 1 0 1
2A8000–2AFFFF
October 10, 2006 S29GL-M_00_B6
A21–A15
16-bit
Address
Range
S29GL-M MirrorBitTM Flash Family
Sector
A21–A15
Sector
Sector
Table 14.
S h e e t
37
D a t a
A22–A15
Sector
Size*
S29GL128M Sector Address Table (Sheet 1 of 3)
8-bit
Address
Range
16-bit
Address
Range
Sector
Sector
Table 15.
S h e e t
A22–A15
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
SA0
0 0 0 0 0 0 0 0 64/32
000000–00FFFF
000000–007FFF
SA41 0 0 1 0 1 0 0 1 64/32
290000–29FFFF
148000–14FFFF
SA1
0 0 0 0 0 0 0 1 64/32
010000–01FFFF
008000–00FFFF
SA42 0 0 1 0 1 0 1 0 64/32
2A0000–2AFFFF
150000–157FFF
SA2
0 0 0 0 0 0 1 0 64/32
020000–02FFFF
010000–017FFF
SA43 0 0 1 0 1 0 1 1 64/32
2B0000–2BFFFF
158000–15FFFF
SA3
0 0 0 0 0 0 1 1 64/32
030000–03FFFF
018000–01FFFF
SA44 0 0 1 0 1 1 0 0 64/32
2C0000–2CFFFF
160000–167FFF
SA4
0 0 0 0 0 1 0 0 64/32
040000–04FFFF
020000–027FFF
SA45 0 0 1 0 1 1 0 1 64/32
2D0000–2DFFFF
168000–16FFFF
SA5
0 0 0 0 0 1 0 1 64/32
050000–05FFFF
028000–02FFFF
SA46 0 0 1 0 1 1 1 0 64/32
2E0000–2EFFFF
170000–177FFF
SA6
0 0 0 0 0 1 1 0 64/32
060000–06FFFF
030000–037FFF
SA47 0 0 1 0 1 1 1 1 64/32
2F0000–2FFFFF
178000–17FFFF
SA7
0 0 0 0 0 1 1 1 64/32
070000–07FFFF
038000–03FFFF
SA48 0 0 1 1 0 0 0 0 64/32
300000–30FFFF
180000–187FFF
SA8
0 0 0 0 1 0 0 0 64/32
080000–08FFFF
040000–047FFF
SA49 0 0 1 1 0 0 0 1 64/32
310000–31FFFF
188000–18FFFF
SA9
0 0 0 0 1 0 0 1 64/32
090000–09FFFF
048000–04FFFF
SA50 0 0 1 1 0 0 1 0 64/32
320000–32FFFF
190000–197FFF
SA10 0 0 0 0 1 0 1 0 64/32
0A0000–0AFFFF
050000–057FFF
SA51 0 0 1 1 0 0 1 1 64/32
330000–33FFFF
198000–19FFFF
SA11 0 0 0 0 1 0 1 1 64/32
0B0000–0BFFFF
058000–05FFFF
SA52 0 0 1 1 0 1 0 0 64/32
340000–34FFFF
1A0000–1A7FFF
SA12 0 0 0 0 1 1 0 0 64/32
0C0000–0CFFFF
060000–067FFF
SA53 0 0 1 1 0 1 0 1 64/32
350000–35FFFF
1A8000–1AFFFF
SA13 0 0 0 0 1 1 0 1 64/32
0D0000–0DFFFF
068000–06FFFF
SA54 0 0 1 1 0 1 1 0 64/32
360000–36FFFF
1B0000–1B7FFF
SA14 0 0 0 0 1 1 1 0 64/32
0E0000–0EFFFF
070000–077FFF
SA55 0 0 1 1 0 1 1 1 64/32
370000–37FFFF
1B8000–1BFFFF
SA15 0 0 0 0 1 1 1 1 64/32
0F0000–0FFFFF
078000–07FFFF
SA56 0 0 1 1 1 0 0 0 64/32
380000–38FFFF
1C0000–1C7FFF
SA16 0 0 0 1 0 0 0 0 64/32
100000–10FFFF
080000–087FFF
SA57 0 0 1 1 1 0 0 1 64/32
390000–39FFFF
1C8000–1CFFFF
SA17 0 0 0 1 0 0 0 1 64/32
110000–11FFFF
088000–08FFFF
SA58 0 0 1 1 1 0 1 0 64/32
3A0000–3AFFFF
1D0000–1D7FFF
SA18 0 0 0 1 0 0 1 0 64/32
120000–12FFFF
090000–097FFF
SA59 0 0 1 1 1 0 1 1 64/32
3B0000–3BFFFF
1D8000–1DFFFF
SA19 0 0 0 1 0 0 1 1 64/32
130000–13FFFF
098000–09FFFF
SA60 0 0 1 1 1 1 0 0 64/32
3C0000–3CFFFF
1E0000–1E7FFF
SA20 0 0 0 1 0 1 0 0 64/32
140000–14FFFF
0A0000–0A7FFF
SA61 0 0 1 1 1 1 0 1 64/32
3D0000–3DFFFF
1E8000–1EFFFF
SA21 0 0 0 1 0 1 0 1 64/32
150000–15FFFF
0A8000–0AFFFF
SA62 0 0 1 1 1 1 1 0 64/32
3E0000–3EFFFF
1F0000–1F7FFF
SA22 0 0 0 1 0 1 1 0 64/32
160000–16FFFF
0B0000–0B7FFF
SA63 0 0 1 1 1 1 1 1 64/32
3F0000–3FFFFF
1F8000–1FFFFF
SA23 0 0 0 1 0 1 1 1 64/32
170000–17FFFF
0B8000–0BFFFF
SA64 0 1 0 0 0 0 0 0 64/32
400000–40FFFF
200000–207FFF
SA24 0 0 0 1 1 0 0 0 64/32
180000–18FFFF
0C0000–0C7FFF
SA65 0 1 0 0 0 0 0 1 64/32
410000–41FFFF
208000–20FFFF
SA25 0 0 0 1 1 0 0 1 64/32
190000–19FFFF
0C8000–0CFFFF
SA66 0 1 0 0 0 0 1 0 64/32
420000–42FFFF
210000–217FFF
SA26 0 0 0 1 1 0 1 0 64/32
1A0000–1AFFFF
0D0000–0D7FFF
SA67 0 1 0 0 0 0 1 1 64/32
430000–43FFFF
218000–21FFFF
SA27 0 0 0 1 1 0 1 1 64/32
1B0000–1BFFFF
0D8000–0DFFFF
SA68 0 1 0 0 0 1 0 0 64/32
440000–44FFFF
220000–227FFF
SA28 0 0 0 1 1 1 0 0 64/32
1C0000–1CFFFF
0E0000–0E7FFF
SA69 0 1 0 0 0 1 0 1 64/32
450000–45FFFF
228000–22FFFF
SA29 0 0 0 1 1 1 0 1 64/32
1D0000–1DFFFF
0E8000–0EFFFF
SA70 0 1 0 0 0 1 1 0 64/32
460000–46FFFF
230000–237FFF
SA30 0 0 0 1 1 1 1 0 64/32
1E0000–1EFFFF
0F0000–0F7FFF
SA71 0 1 0 0 0 1 1 1 64/32
470000–47FFFF
238000–23FFFF
SA31 0 0 0 1 1 1 1 1 64/32
1F0000–1FFFFF
0F8000–0FFFFF
SA72 0 1 0 0 1 0 0 0 64/32
480000–48FFFF
240000–247FFF
SA32 0 0 1 0 0 0 0 0 64/32
200000–20FFFF
100000–107FFF
SA73 0 1 0 0 1 0 0 1 64/32
490000–49FFFF
248000–24FFFF
SA33 0 0 1 0 0 0 0 1 64/32
210000–21FFFF
108000–10FFFF
SA74 0 1 0 0 1 0 1 0 64/32
4A0000–4AFFFF
250000–257FFF
SA34 0 0 1 0 0 0 1 0 64/32
220000–22FFFF
110000–117FFF
SA75 0 1 0 0 1 0 1 1 64/32
4B0000–4BFFFF
258000–25FFFF
SA35 0 0 1 0 0 0 1 1 64/32
230000–23FFFF
118000–11FFFF
SA76 0 1 0 0 1 1 0 0 64/32
4C0000–4CFFFF
260000–267FFF
SA36 0 0 1 0 0 1 0 0 64/32
240000–24FFFF
120000–127FFF
SA77 0 1 0 0 1 1 0 1 64/32
4D0000–4DFFFF
268000–26FFFF
SA37 0 0 1 0 0 1 0 1 64/32
250000–25FFFF
128000–12FFFF
SA78 0 1 0 0 1 1 1 0 64/32
4E0000–4EFFFF
270000–277FFF
SA38 0 0 1 0 0 1 1 0 64/32
260000–26FFFF
130000–137FFF
SA79 0 1 0 0 1 1 1 1 64/32
4F0000–4FFFFF
278000–27FFFF
SA39 0 0 1 0 0 1 1 1 64/32
270000–27FFFF
138000–13FFFF
SA80 0 1 0 1 0 0 0 0 64/32
500000–50FFFF
280000–287FFF
SA40 0 0 1 0 1 0 0 0 64/32
280000–28FFFF
140000–147FFF
SA81 0 1 0 1 0 0 0 1 64/32
510000–51FFFF
288000–28FFFF
38
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
Table 15.
S h e e t
S29GL128M Sector Address Table (Sheet 2 of 3)
SA82 0 1 0 1 0 0 1 0 64/32
520000–52FFFF
290000–297FFF
SA158 1 0 0 1 1 1 1 0 64/32
SA83 0 1 0 1 0 0 1 1 64/32
530000–53FFFF
298000–29FFFF
SA159 1 0 0 1 1 1 1 1 64/32
9F0000–9FFFFF
4F8000–4FFFFF
SA84 0 1 0 1 0 1 0 0 64/32
540000–54FFFF
2A0000–2A7FFF
SA160 1 0 1 0 0 0 0 0 64/32
A00000–A0FFFF
500000–507FFF
SA85 0 1 0 1 0 1 0 1 64/32
550000–55FFFF
2A8000–2AFFFF
SA161 1 0 1 0 0 0 0 1 64/32
A10000–A1FFFF
508000–50FFFF
SA86 0 1 0 1 0 1 1 0 64/32
560000–56FFFF
2B0000–2B7FFF
SA162 1 0 1 0 0 0 1 0 64/32
A20000–A2FFFF
510000–517FFF
SA87 0 1 0 1 0 1 1 1 64/32
570000–57FFFF
2B8000–2BFFFF
SA163 1 0 1 0 0 0 1 1 64/32
A30000–A3FFFF
518000–51FFFF
SA88 0 1 0 1 1 0 0 0 64/32
580000–58FFFF
2C0000–2C7FFF
SA164 1 0 1 0 0 1 0 0 64/32
A40000–A4FFFF
520000–527FFF
SA89 0 1 0 1 1 0 0 1 64/32
590000–59FFFF
2C8000–2CFFFF
SA165 1 0 1 0 0 1 0 1 64/32
A50000–A5FFFF
528000–52FFFF
SA90 0 1 0 1 1 0 1 0 64/32
5A0000–5AFFFF
2D0000–2D7FFF
SA166 1 0 1 0 0 1 1 0 64/32
A60000–A6FFFF
530000–537FFF
SA91 0 1 0 1 1 0 1 1 64/32
5B0000–5BFFFF
2D8000–2DFFFF
SA167 1 0 1 0 0 1 1 1 64/32
A70000–A7FFFF
538000–53FFFF
SA92 0 1 0 1 1 1 0 0 64/32
5C0000–5CFFFF
2E0000–2E7FFF
SA168 1 0 1 0 1 0 0 0 64/32
A80000–A8FFFF
540000–547FFF
SA93 0 1 0 1 1 1 0 1 64/32
5D0000–5DFFFF
2E8000–2EFFFF
SA169 1 0 1 0 1 0 0 1 64/32
A90000–A9FFFF
548000–54FFFF
SA94 0 1 0 1 1 1 1 0 64/32
5E0000–5EFFFF
2F0000–2F7FFF
SA170 1 0 1 0 1 0 1 0 64/32
AA0000–AAFFFF
550000–557FFF
Sector
Size*
Sector
16-bit
Address
Range
Sector
8-bit
Address
Range
A22–A15
A22–A15
Sector
Size*
8-bit
Address
Range
16-bit
Address
Range
9E0000–9EFFFF
4F0000–4F7FFF
SA95 0 1 0 1 1 1 1 1 64/32
5F0000–5FFFFF
2F8000–2FFFFF
SA171 1 0 1 0 1 0 1 1 64/32
AB0000–ABFFFF
558000–55FFFF
SA96 0 1 1 0 0 0 0 0 64/32
600000–60FFFF
300000–307FFF
SA172 1 0 1 0 1 1 0 0 64/32
AC0000–ACFFFF
560000–567FFF
SA97 0 1 1 0 0 0 0 1 64/32
610000–61FFFF
308000–30FFFF
SA173 1 0 1 0 1 1 0 1 64/32
AD0000–ADFFFF
568000–56FFFF
SA98 0 1 1 0 0 0 1 0 64/32
620000–62FFFF
310000–317FFF
SA174 1 0 1 0 1 1 1 0 64/32
AE0000–AEFFFF
570000–577FFF
SA66 0 1 0 0 0 0 1 0 64/32
420000–42FFFF
210000–217FFF
SA175 1 0 1 0 1 1 1 1 64/32
AF0000–AFFFFF
578000–57FFFF
SA67 0 1 0 0 0 0 1 1 64/32
430000–43FFFF
218000–21FFFF
SA176 1 0 1 1 0 0 0 0 64/32
B00000–B0FFFF
580000–587FFF
SA136 1 0 0 0 1 0 0 0 64/32
880000–88FFFF
440000–447FFF
SA177 1 0 1 1 0 0 0 1 64/32
B10000–B1FFFF
588000–58FFFF
SA137 1 0 0 0 1 0 0 1 64/32
890000–89FFFF
448000–44FFFF
SA178 1 0 1 1 0 0 1 0 64/32
B20000–B2FFFF
590000–597FFF
SA138 1 0 0 0 1 0 1 0 64/32
8A0000–8AFFFF
450000–457FFF
SA179 1 0 1 1 0 0 1 1 64/32
B30000–B3FFFF
598000–59FFFF
SA139 1 0 0 0 1 0 1 1 64/32
8B0000–8BFFFF
458000–45FFFF
SA180 1 0 1 1 0 1 0 0 64/32
B40000–B4FFFF
5A0000–5A7FFF
SA140 1 0 0 0 1 1 0 0 64/32
8C0000–8CFFFF
460000–467FFF
SA181 1 0 1 1 0 1 0 1 64/32
B50000–B5FFFF
5A8000–5AFFFF
SA141 1 0 0 0 1 1 0 1 64/32
8D0000–8DFFFF
468000–46FFFF
SA182 1 0 1 1 0 1 1 0 64/32
B60000–B6FFFF
5B0000–5B7FFF
SA142 1 0 0 0 1 1 1 0 64/32
8E0000–8EFFFF
470000–477FFF
SA183 1 0 1 1 0 1 1 1 64/32
B70000–B7FFFF
5B8000–5BFFFF
SA143 1 0 0 0 1 1 1 1 64/32
8F0000–8FFFFF
478000–47FFFF
SA184 1 0 1 1 1 0 0 0 64/32
B80000–B8FFFF
5C0000–5C7FFF
SA144 1 0 0 1 0 0 0 0 64/32
900000–90FFFF
480000–487FFF
SA185 1 0 1 1 1 0 0 1 64/32
B90000–B9FFFF
5C8000–5CFFFF
SA145 1 0 0 1 0 0 0 1 64/32
910000–91FFFF
488000–48FFFF
SA186 1 0 1 1 1 0 1 0 64/32
BA0000–BAFFFF
5D0000–5D7FFF
SA146 1 0 0 1 0 0 1 0 64/32
920000–92FFFF
490000–497FFF
SA187 1 0 1 1 1 0 1 1 64/32
BB0000–BBFFFF
5D8000–5DFFFF
SA147 1 0 0 1 0 0 1 1 64/32
930000–93FFFF
498000–49FFFF
SA188 1 0 1 1 1 1 0 0 64/32
BC0000–BCFFFF
5E0000–5E7FFF
SA148 1 0 0 1 0 1 0 0 64/32
940000–94FFFF
4A0000–4A7FFF
SA189 1 0 1 1 1 1 0 1 64/32
BD0000–BDFFFF
5E8000–5EFFFF
SA149 1 0 0 1 0 1 0 1 64/32
950000–95FFFF
4A8000–4AFFFF
SA190 1 0 1 1 1 1 1 0 64/32
BE0000–BEFFFF
5F0000–5F7FFF
SA150 1 0 0 1 0 1 1 0 64/32
960000–96FFFF
4B0000–4B7FFF
SA191 1 0 1 1 1 1 1 1 64/32
BF0000–BFFFFF
5F8000–5FFFFF
SA151 1 0 0 1 0 1 1 1 64/32
970000–97FFFF
4B8000–4BFFFF
SA192 1 1 0 0 0 0 0 0 64/32
C00000–C0FFFF
600000–607FFF
SA152 1 0 0 1 1 0 0 0 64/32
980000–98FFFF
4C0000–4C7FFF
SA193 1 1 0 0 0 0 0 1 64/32
C10000–C1FFFF
608000–60FFFF
SA153 1 0 0 1 1 0 0 1 64/32
990000–99FFFF
4C8000–4CFFFF
SA194 1 1 0 0 0 0 1 0 64/32
C20000–C2FFFF
610000–617FFF
SA154 1 0 0 1 1 0 1 0 64/32
9A0000–9AFFFF
4D0000–4D7FFF
SA195 1 1 0 0 0 0 1 1 64/32
C30000–C3FFFF
618000–61FFFF
SA155 1 0 0 1 1 0 1 1 64/32
9B0000–9BFFFF
4D8000–4DFFFF
SA196 1 1 0 0 0 1 0 0 64/32
C40000–C4FFFF
620000–627FFF
SA156 1 0 0 1 1 1 0 0 64/32
9C0000–9CFFFF
4E0000–4E7FFF
SA197 1 1 0 0 0 1 0 1 64/32
C50000–C5FFFF
628000–62FFFF
SA157 1 0 0 1 1 1 0 1 64/32
9D0000–9DFFFF
4E8000–4EFFFF
SA198 1 1 0 0 0 1 1 0 64/32
C60000–C6FFFF
630000–637FFF
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
39
D a t a
Table 15.
S h e e t
S29GL128M Sector Address Table (Sheet 3 of 3)
8-bit
Address
Range
16-bit
Address
Range
SA199 1 1 0 0 0 1 1 1 64/32
C70000–C7FFFF
638000–63FFFF
SA228 1 1 1 0 0 1 0 0 64/32
E40000–E4FFFF
720000–727FFF
SA200 1 1 0 0 1 0 0 0 64/32
C80000–C8FFFF
SA201 1 1 0 0 1 0 0 1 64/32
C90000–C9FFFF
640000–647FFF
SA229 1 1 1 0 0 1 0 1 64/32
E50000–E5FFFF
728000–72FFFF
648000–64FFFF
SA230 1 1 1 0 0 1 1 0 64/32
E60000–E6FFFF
730000–737FFF
SA202 1 1 0 0 1 0 1 0 64/32
CA0000–CAFFFF
650000–657FFF
SA231 1 1 1 0 0 1 1 1 64/32
E70000–E7FFFF
738000–73FFFF
SA203 1 1 0 0 1 0 1 1 64/32
CB0000–CBFFFF
658000–65FFFF
SA232 1 1 1 0 1 0 0 0 64/32
E80000–E8FFFF
740000–747FFF
SA204 1 1 0 0 1 1 0 0 64/32
CC0000–CCFFFF
660000–667FFF
SA233 1 1 1 0 1 0 0 1 64/32
E90000–E9FFFF
748000–74FFFF
SA205 1 1 0 0 1 1 0 1 64/32
CD0000–CDFFFF
668000–66FFFF
SA234 1 1 1 0 1 0 1 0 64/32
EA0000–EAFFFF
750000–757FFF
SA206 1 1 0 0 1 1 1 0 64/32
CE0000–CEFFFF
670000–677FFF
SA235 1 1 1 0 1 0 1 1 64/32
EB0000–EBFFFF
758000–75FFFF
SA207 1 1 0 0 1 1 1 1 64/32
CF0000–CFFFFF
678000–67FFFF
SA236 1 1 1 0 1 1 0 0 64/32
EC0000–ECFFFF
760000–767FFF
SA208 1 1 0 1 0 0 0 0 64/32
D00000–D0FFFF
680000–687FFF
SA237 1 1 1 0 1 1 0 1 64/32
ED0000–EDFFFF
768000–76FFFF
SA209 1 1 0 1 0 0 0 1 64/32
D10000–D1FFFF
688000–68FFFF
SA238 1 1 1 0 1 1 1 0 64/32
EE0000–EEFFFF
770000–777FFF
SA210 1 1 0 1 0 0 1 0 64/32
D20000–D2FFFF
690000–697FFF
SA239 1 1 1 0 1 1 1 1 64/32
EF0000–EFFFFF
778000–77FFFF
SA211 1 1 0 1 0 0 1 1 64/32
D30000–D3FFFF
698000–69FFFF
SA240 1 1 1 1 0 0 0 0 64/32
F00000–F0FFFF
780000–787FFF
SA212 1 1 0 1 0 1 0 0 64/32
D40000–D4FFFF
6A0000–6A7FFF
SA241 1 1 1 1 0 0 0 1 64/32
F10000–F1FFFF
788000–78FFFF
SA213 1 1 0 1 0 1 0 1 64/32
D50000–D5FFFF
6A8000–6AFFFF
SA242 1 1 1 1 0 0 1 0 64/32
F20000–F2FFFF
790000–797FFF
SA214 1 1 0 1 0 1 1 0 64/32
D60000–D6FFFF
6B0000–6B7FFF
SA243 1 1 1 1 0 0 1 1 64/32
F30000–F3FFFF
798000–79FFFF
SA215 1 1 0 1 0 1 1 1 64/32
D70000–D7FFFF
6B8000–6BFFFF
SA244 1 1 1 1 0 1 0 0 64/32
F40000–F4FFFF
7A0000–7A7FFF
SA216 1 1 0 1 1 0 0 0 64/32
D80000–D8FFFF
6C0000–6C7FFF
SA245 1 1 1 1 0 1 0 1 64/32
F50000–F5FFFF
7A8000–7AFFFF
SA217 1 1 0 1 1 0 0 1 64/32
D90000–D9FFFF
6C8000–6CFFFF
SA246 1 1 1 1 0 1 1 0 64/32
F60000–F6FFFF
7B0000–7B7FFF
SA218 1 1 0 1 1 0 1 0 64/32
DA0000–DAFFFF
6D0000–6D7FFF
SA247 1 1 1 1 0 1 1 1 64/32
F70000–F7FFFF
7B8000–7BFFFF
SA219 1 1 0 1 1 0 1 1 64/32
DB0000–DBFFFF
6D8000–6DFFFF
SA248 1 1 1 1 1 0 0 0 64/32
F80000–F8FFFF
7C0000–7C7FFF
SA220 1 1 0 1 1 1 0 0 64/32
DC0000–DCFFFF
6E0000–6E7FFF
SA249 1 1 1 1 1 0 0 1 64/32
F90000–F9FFFF
7C8000–7CFFFF
SA221 1 1 0 1 1 1 0 1 64/32
DD0000–DDFFFF
6E8000–6EFFFF
SA250 1 1 1 1 1 0 1 0 64/32
FA0000–FAFFFF
7D0000–7D7FFF
SA222 1 1 0 1 1 1 1 0 64/32
DE0000–DEFFFF
6F0000–6F7FFF
SA251 1 1 1 1 1 0 1 1 64/32
FB0000–FBFFFF
7D8000–7DFFFF
SA223 1 1 0 1 1 1 1 1 64/32
DF0000–DFFFFF
6F8000–6FFFFF
SA252 1 1 1 1 1 1 0 0 64/32
FC0000–FCFFFF
7E0000–7E7FFF
SA224 1 1 1 0 0 0 0 0 64/32
E00000–E0FFFF
700000–707FFF
SA253 1 1 1 1 1 1 0 1 64/32
FD0000–FDFFFF
7E8000–7EFFFF
SA225 1 1 1 0 0 0 0 1 64/32
E10000–E1FFFF
708000–70FFFF
SA254 1 1 1 1 1 1 1 0 64/32
FE0000–FEFFFF
7F0000–7F7FFF
SA226 1 1 1 0 0 0 1 0 64/32
E20000–E2FFFF
710000–717FFF
SA255 1 1 1 1 1 1 1 1 64/32
FF0000–FFFFFF
7F8000–7FFFFF
SA227 1 1 1 0 0 0 1 1 64/32
E30000–E3FFFF
718000–71FFFF
Sector
Size*
Sector
16-bit
Address
Range
Sector
8-bit
Address
Range
A22–A15
A22–A15
Sector
Size*
* Sector sizes are given in Kbytes/Kwords.
40
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
Sector
S29GL256M Sector Address Table (Sheet 1 of 6)
Sector
Table 16.
S h e e t
A23–A15
8-bit
Address
Range
16-bit
Address
Range
A23–A15
8-bit
Address
Range
16-bit
Address
Range
SA0
0 0 0 0 0 0 0 0 0
0000000–000FFFF
000000–007FFF
SA1
0 0 0 0 0 0 0 0 1
0010000–001FFFF
008000–00FFFF
SA44
0 0 0 1 0 1 1 0 0
02C0000–02CFFFF
160000–167FFF
SA45
0 0 0 1 0 1 1 0 1 02D0000–02DFFFF
SA2
0 0 0 0 0 0 0 1 0
0020000–002FFFF
010000–017FFF
168000–16FFFF
SA46
0 0 0 1 0 1 1 1 0
170000–177FFF
SA3
0 0 0 0 0 0 0 1 1
0030000–003FFFF
SA4
0 0 0 0 0 0 1 0 0
0040000–004FFFF
018000–01FFFF
SA47
0 0 0 1 0 1 1 1 1
02F0000–02FFFFF
178000–17FFFF
020000–027FFF
SA48
0 0 0 1 1 0 0 0 0
0300000–030FFFF
180000–187FFF
SA5
0 0 0 0 0 0 1 0 1
0050000–005FFFF
028000–02FFFF
SA49
0 0 0 1 1 0 0 0 1
0310000–031FFFF
188000–18FFFF
SA6
0 0 0 0 0 0 1 1 0
SA7
0 0 0 0 0 0 1 1 1
0060000–006FFFF
030000–037FFF
SA50
0 0 0 1 1 0 0 1 0
0320000–032FFFF
190000–197FFF
0070000–007FFFF
038000–03FFFF
SA51
0 0 0 1 1 0 0 1 1
0330000–033FFFF
198000–19FFFF
SA8
SA9
0 0 0 0 0 1 0 0 0
0080000–008FFFF
040000–047FFF
SA52
0 0 0 1 1 0 1 0 0
0340000–034FFFF
1A0000–1A7FFF
0 0 0 0 0 1 0 0 1
0090000–009FFFF
048000–04FFFF
SA53
0 0 0 1 1 0 1 0 1
0350000–035FFFF
1A8000–1AFFFF
SA10
0 0 0 0 0 1 0 1 0
00A0000–00AFFFF
050000–057FFF
SA54
0 0 0 1 1 0 1 1 0
0360000–036FFFF
1B0000–1B7FFF
SA11
0 0 0 0 0 1 0 1 1
00B0000–00BFFFF
058000–05FFFF
SA55
0 0 0 1 1 0 1 1 1
0370000–037FFFF
1B8000–1BFFFF
SA12
0 0 0 0 0 1 1 0 0
00C0000–00CFFFF
060000–067FFF
SA56
0 0 0 1 1 1 0 0 0
0380000–038FFFF
1C0000–1C7FFF
SA13
0 0 0 0 0 1 1 0 1
00D0000–00DFFFF
068000–06FFFF
SA57
0 0 0 1 1 1 0 0 1
0390000–039FFFF
1C8000–1CFFFF
SA14
0 0 0 0 0 1 1 1 0
00E0000–00EFFFF
070000–077FFF
SA58
0 0 0 1 1 1 0 1 0
03A0000–03AFFFF
1D0000–1D7FFF
SA15
0 0 0 0 0 1 1 1 1
00F0000–00FFFFF
078000–07FFFF
SA59
0 0 0 1 1 1 0 1 1
03B0000–03BFFFF
1D8000–1DFFFF
02E0000–02EFFFF
SA16
0 0 0 0 1 0 0 0 0
0100000–010FFFF
080000–087FFF
SA60
0 0 0 1 1 1 1 0 0
03C0000–03CFFFF
1E0000–1E7FFF
SA17
0 0 0 0 1 0 0 0 1
0110000–011FFFF
088000–08FFFF
SA61
0 0 0 1 1 1 1 0 1 03D0000–03DFFFF
1E8000–1EFFFF
SA18
0 0 0 0 1 0 0 1 0
0120000–012FFFF
090000–097FFF
SA62
0 0 0 1 1 1 1 1 0
1F0000–1F7FFF
03E0000–03EFFFF
SA19
0 0 0 0 1 0 0 1 1
0130000–013FFFF
098000–09FFFF
SA63
0 0 0 1 1 1 1 1 1
03F0000–03FFFFF
1F8000–1FFFFF
SA20
0 0 0 0 1 0 1 0 0
0140000–014FFFF
0A0000–0A7FFF
SA64
0 0 1 0 0 0 0 0 0
0400000–040FFFF
200000–207FFF
SA21
0 0 0 0 1 0 1 0 1
0150000–015FFFF
0A8000–0AFFFF
SA65
0 0 1 0 0 0 0 0 1
0410000–041FFFF
208000–20FFFF
SA22
0 0 0 0 1 0 1 1 0
0160000–016FFFF
0B0000–0B7FFF
SA66
0 0 1 0 0 0 0 1 0
0420000–042FFFF
210000–217FFF
SA23
0 0 0 0 1 0 1 1 1
0170000–017FFFF
0B8000–0BFFFF
SA67
0 0 1 0 0 0 0 1 1
0430000–043FFFF
218000–21FFFF
220000–227FFF
SA24
0 0 0 0 1 1 0 0 0
0180000–018FFFF
0C0000–0C7FFF
SA68
0 0 1 0 0 0 1 0 0 0440000–044FFFF
SA25
0 0 0 0 1 1 0 0 1
0190000–019FFFF
0C8000–0CFFFF
SA69
0 0 1 0 0 0 1 0 1 0450000–045FFFF
228000–22FFFF
SA26
0 0 0 0 1 1 0 1 0
01A0000–01AFFFF
0D0000–0D7FFF
SA70
0 0 1 0 0 0 1 1 0 0460000–046FFFF
230000–237FFF
SA27
0 0 0 0 1 1 0 1 1
01B0000–01BFFFF
0D8000–0DFFFF
SA71
0 0 1 0 0 0 1 1 1 0470000–047FFFF
238000–23FFFF
SA28
0 0 0 0 1 1 1 0 0
01C0000–01CFFFF
0E0000–0E7FFF
SA72
0 0 1 0 0 1 0 0 0 0480000–048FFFF
240000–247FFF
SA29
0 0 0 0 1 1 1 0 1
01D0000–01DFFFF
0E8000–0EFFFF
SA73
0 0 1 0 0 1 0 0 1 0490000–049FFFF
248000–24FFFF
SA30
0 0 0 0 1 1 1 1 0
01E0000–01EFFFF
0F0000–0F7FFF
SA74
0 0 1 0 0 1 0 1 0 04A0000–04AFFFF
250000–257FFF
SA31
0 0 0 0 1 1 1 1 1
01F0000–01FFFFF
0F8000–0FFFFF
SA75
0 0 1 0 0 1 0 1 1 04B0000–04BFFFF
258000–25FFFF
SA32
0 0 0 1 0 0 0 0 0
0200000–020FFFF
100000–107FFF
SA76
0 0 1 0 0 1 1 0 0 04C0000–04CFFFF
260000–267FFF
SA33
0 0 0 1 0 0 0 0 1
0210000–021FFFF
108000–10FFFF
SA77
0 0 1 0 0 1 1 0 1 04D0000–04DFFFF
268000–26FFFF
SA34
0 0 0 1 0 0 0 1 0
0220000–022FFFF
110000–117FFF
SA78
0 0 1 0 0 1 1 1 0 04E0000–04EFFFF
270000–277FFF
SA35
0 0 0 1 0 0 0 1 1
0230000–023FFFF
118000–11FFFF
SA79
0 0 1 0 0 1 1 1 1 04F0000–04FFFFF
278000–27FFFF
SA36
0 0 0 1 0 0 1 0 0
0240000–024FFFF
120000–127FFF
SA80
0 0 1 0 1 0 0 0 0 0500000–050FFFF
280000–287FFF
SA37
0 0 0 1 0 0 1 0 1
0250000–025FFFF
128000–12FFFF
SA81
0 0 1 0 1 0 0 0 1 0510000–051FFFF
288000–28FFFF
SA38
0 0 0 1 0 0 1 1 0
0260000–026FFFF
130000–137FFF
SA82
0 0 1 0 1 0 0 1 0 0520000–052FFFF
290000–297FFF
SA39
0 0 0 1 0 0 1 1 1
0270000–027FFFF
138000–13FFFF
SA83
0 0 1 0 1 0 0 1 1 0530000–053FFFF
298000–29FFFF
SA40
0 0 0 1 0 1 0 0 0
0280000–028FFFF
140000–147FFF
SA84
0 0 1 0 1 0 1 0 0 0540000–054FFFF
2A0000–2A7FFF
SA41
0 0 0 1 0 1 0 0 1
0290000–029FFFF
148000–14FFFF
SA85
0 0 1 0 1 0 1 0 1 0550000–055FFFF
2A8000–2AFFFF
SA42
0 0 0 1 0 1 0 1 0
02A0000–02AFFFF
150000–157FFF
SA86
0 0 1 0 1 0 1 1 0 0560000–056FFFF
2B0000–2B7FFF
SA43
0 0 0 1 0 1 0 1 1
02B0000–02BFFFF
158000–15FFFF
SA87
0 0 1 0 1 0 1 1 1 0570000–057FFFF
2B8000–2BFFFF
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
41
D a t a
S29GL256M Sector Address Table (Sheet 2 of 6)
A23–A15
8-bit
Address
Range
16-bit
Address
Range
SA88
0 0 1 0 1 1 0 0 0
0580000–058FFFF
2C0000–2C7FFF
SA133 0 1 0 0 0 0 1 0 1 0850000–085FFFF
428000–42FFFF
SA89
0 0 1 0 1 1 0 0 1
0590000–059FFFF
2C8000–2CFFFF
SA134 0 1 0 0 0 0 1 1 0 0860000–086FFFF
430000–437FFF
SA90
0 0 1 0 1 1 0 1 0
05A0000–05AFFFF
2D0000–2D7FFF
SA135 0 1 0 0 0 0 1 1 1 0870000–087FFFF
438000–43FFFF
SA91
0 0 1 0 1 1 0 1 1
05B0000–05BFFFF
2D8000–2DFFFF
SA136 0 1 0 0 0 1 0 0 0 0880000–088FFFF
440000–447FFF
SA92
0 0 1 0 1 1 1 0 0
05C0000–05CFFFF
2E0000–2E7FFF
SA137 0 1 0 0 0 1 0 0 1 0890000–089FFFF
448000–44FFFF
SA93
0 0 1 0 1 1 1 0 1 05D0000–05DFFFF
2E8000–2EFFFF
SA138 0 1 0 0 0 1 0 1 0 08A0000–08AFFFF
450000–457FFF
SA94
0 0 1 0 1 1 1 1 0
2F0000–2F7FFF
SA139 0 1 0 0 0 1 0 1 1 08B0000–08BFFFF
458000–45FFFF
SA95
0 0 1 0 1 1 1 1 1
05F0000–05FFFFF
2F8000–2FFFFF
SA140 0 1 0 0 0 1 1 0 0 08C0000–08CFFFF
460000–467FFF
SA96
0 0 1 1 0 0 0 0 0
0600000–060FFFF
300000–307FFF
SA141 0 1 0 0 0 1 1 0 1 08D0000–08DFFFF
468000–46FFFF
SA97
0 0 1 1 0 0 0 0 1
0610000–061FFFF
308000–30FFFF
SA142 0 1 0 0 0 1 1 1 0 08E0000–08EFFFF
470000–477FFF
SA98
0 0 1 1 0 0 0 1 0
0620000–062FFFF
310000–317FFF
SA143 0 1 0 0 0 1 1 1 1 08F0000–08FFFFF
478000–47FFFF
SA99
0 0 1 1 0 0 0 1 1
0630000–063FFFF
318000–31FFFF
SA144 0 1 0 0 1 0 0 0 0 0900000–090FFFF
480000–487FFF
SA100
0 0 1 1 0 0 1 0 0
0640000–064FFFF
320000–327FFF
SA145 0 1 0 0 1 0 0 0 1 0910000–091FFFF
488000–48FFFF
SA101
0 0 1 1 0 0 1 0 1
0650000–065FFFF
328000–32FFFF
SA146 0 1 0 0 1 0 0 1 0 0920000–092FFFF
490000–497FFF
SA102
0 0 1 1 0 0 1 1 0
0660000–066FFFF
330000–337FFF
SA147 0 1 0 0 1 0 0 1 1 0930000–093FFFF
498000–49FFFF
SA103
0 0 1 1 0 0 1 1 1
0670000–067FFFF
338000–33FFFF
SA148 0 1 0 0 1 0 1 0 0 0940000–094FFFF
4A0000–4A7FFF
SA104
0 0 1 1 0 1 0 0 0
0680000–068FFFF
340000–347FFF
SA149 0 1 0 0 1 0 1 0 1 0950000–095FFFF
4A8000–4AFFFF
SA105
0 0 1 1 0 1 0 0 1
0690000–069FFFF
348000–34FFFF
SA150 0 1 0 0 1 0 1 1 0 0960000–096FFFF
4B0000–4B7FFF
05E0000–05EFFFF
Sector
Sector
Table 16.
S h e e t
A23–A15
8-bit
Address
Range
16-bit
Address
Range
SA106
0 0 1 1 0 1 0 1 0
06A0000–06AFFFF
350000–357FFF
SA151 0 1 0 0 1 0 1 1 1 0970000–097FFFF
4B8000–4BFFFF
SA107
0 0 1 1 0 1 0 1 1
06B0000–06BFFFF
358000–35FFFF
SA152 0 1 0 0 1 1 0 0 0 0980000–098FFFF
4C0000–4C7FFF
SA108
0 0 1 1 0 1 1 0 0
06C0000–06CFFFF
360000–367FFF
SA153 0 1 0 0 1 1 0 0 1 0990000–099FFFF
4C8000–4CFFFF
SA109
0 0 1 1 0 1 1 0 1 06D0000–06DFFFF
368000–36FFFF
SA154 0 1 0 0 1 1 0 1 0 09A0000–09AFFFF
4D0000–4D7FFF
SA110
0 0 1 1 0 1 1 1 0
370000–377FFF
SA155 0 1 0 0 1 1 0 1 1 09B0000–09BFFFF
4D8000–4DFFFF
06E0000–06EFFFF
SA111
0 0 1 1 0 1 1 1 1
06F0000–06FFFFF
378000–37FFFF
SA156 0 1 0 0 1 1 1 0 0 09C0000–09CFFFF
4E0000–4E7FFF
SA112
0 0 1 1 1 0 0 0 0
0700000–070FFFF
380000–387FFF
SA157 0 1 0 0 1 1 1 0 1 09D0000–09DFFFF
4E8000–4EFFFF
SA113
0 0 1 1 1 0 0 0 1
0710000–071FFFF
388000–38FFFF
SA158 0 1 0 0 1 1 1 1 0 09E0000–09EFFFF
4F0000–4F7FFF
SA114
0 0 1 1 1 0 0 1 0
0720000–072FFFF
390000–397FFF
SA159 0 1 0 0 1 1 1 1 1 09F0000–09FFFFF
4F8000–4FFFFF
SA115
0 0 1 1 1 0 0 1 1
0730000–073FFFF
398000–39FFFF
SA160 0 1 0 1 0 0 0 0 0 0A00000–0A0FFFF
500000–507FFF
SA116
0 0 1 1 1 0 1 0 0
0740000–074FFFF
3A0000–3A7FFF
SA161 0 1 0 1 0 0 0 0 1 0A10000–0A1FFFF
508000–50FFFF
SA117
0 0 1 1 1 0 1 0 1
0750000–075FFFF
3A8000–3AFFFF
SA162 0 1 0 1 0 0 0 1 0 0A20000–0A2FFFF
510000–517FFF
SA118
0 0 1 1 1 0 1 1 0
0760000–076FFFF
3B0000–3B7FFF
SA163 0 1 0 1 0 0 0 1 1 0A30000–0A3FFFF
518000–51FFFF
520000–527FFF
SA119
0 0 1 1 1 0 1 1 1
0770000–077FFFF
3B8000–3BFFFF
SA164 0 1 0 1 0 0 1 0 0 0A40000–0A4FFFF
SA120
0 0 1 1 1 1 0 0 0
0780000–078FFFF
3C0000–3C7FFF
SA165 0 1 0 1 0 0 1 0 1 0A50000–0A5FFFF
528000–52FFFF
SA121
0 0 1 1 1 1 0 0 1
0790000–079FFFF
3C8000–3CFFFF
SA166 0 1 0 1 0 0 1 1 0 0A60000–0A6FFFF
530000–537FFF
SA122
0 0 1 1 1 1 0 1 0
07A0000–07AFFFF
3D0000–3D7FFF
SA167 0 1 0 1 0 0 1 1 1 0A70000–0A7FFFF
538000–53FFFF
SA123
0 0 1 1 1 1 0 1 1
07B0000–07BFFFF
3D8000–3DFFFF
SA168 0 1 0 1 0 1 0 0 0 0A80000–0A8FFFF
540000–547FFF
SA124
0 0 1 1 1 1 1 0 0
07C0000–07CFFFF
3E0000–3E7FFF
SA169 0 1 0 1 0 1 0 0 1 0A90000–0A9FFFF
548000–54FFFF
SA125
0 0 1 1 1 1 1 0 1 07D0000–07DFFFF
3E8000–3EFFFF
SA170 0 1 0 1 0 1 0 1 0 0AA0000–0AAFFFF
550000–557FFF
SA126
0 0 1 1 1 1 1 1 0
3F0000–3F7FFF
SA171 0 1 0 1 0 1 0 1 1 0AB0000–0ABFFFF
558000–55FFFF
560000–567FFF
07E0000–07EFFFF
SA127
0 0 1 1 1 1 1 1 1
07F0000–07FFFFF
3F8000–3FFFFF
SA172 0 1 0 1 0 1 1 0 0 0AC0000–0ACFFFF
SA128
0 1 0 0 0 0 0 0 0
0800000–080FFFF
400000–407FFF
SA173 0 1 0 1 0 1 1 0 1 0AD0000–0ADFFFF
568000–56FFFF
SA129
0 1 0 0 0 0 0 0 1
0810000–081FFFF
408000–40FFFF
SA174 0 1 0 1 0 1 1 1 0 0AE0000–0AEFFFF
570000–577FFF
SA130
0 1 0 0 0 0 0 1 0
0820000–082FFFF
410000–417FFF
SA175 0 1 0 1 0 1 1 1 1 0AF0000–0AFFFFF
578000–57FFFF
SA131
0 1 0 0 0 0 0 1 1
0830000–083FFFF
418000–41FFFF
SA176 0 1 0 1 1 0 0 0 0 0B00000–0B0FFFF
580000–587FFF
SA132
0 1 0 0 0 0 1 0 0
0840000–084FFFF
420000–427FFF
SA177 0 1 0 1 1 0 0 0 1 0B10000–0B1FFFF
588000–58FFFF
42
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S29GL256M Sector Address Table (Sheet 3 of 6)
A23–A15
8-bit
Address
Range
16-bit
Address
Range
SA178
0 1 0 1 1 0 0 1 0
0B20000–0B2FFFF
590000–597FFF
SA223 0 1 1 0 1 1 1 1 1 0DF0000–0DFFFFF
6F8000–6FFFFF
SA179
0 1 0 1 1 0 0 1 1
0B30000–0B3FFFF
598000–59FFFF
SA224 0 1 1 1 0 0 0 0 0 0E00000–0E0FFFF
700000–707FFF
SA180
0 1 0 1 1 0 1 0 0
0B40000–0B4FFFF
5A0000–5A7FFF
SA225 0 1 1 1 0 0 0 0 1 0E10000–0E1FFFF
708000–70FFFF
SA181
0 1 0 1 1 0 1 0 1
0B50000–0B5FFFF
5A8000–5AFFFF
SA226 0 1 1 1 0 0 0 1 0 0E20000–0E2FFFF
710000–717FFF
SA182
0 1 0 1 1 0 1 1 0
0B60000–0B6FFFF
5B0000–5B7FFF
SA227 0 1 1 1 0 0 0 1 1 0E30000–0E3FFFF
718000–71FFFF
SA183
0 1 0 1 1 0 1 1 1
0B70000–0B7FFFF
5B8000–5BFFFF
SA228 0 1 1 1 0 0 1 0 0 0E40000–0E4FFFF
720000–727FFF
SA184
0 1 0 1 1 1 0 0 0
0B80000–0B8FFFF
5C0000–5C7FFF
SA229 0 1 1 1 0 0 1 0 1 0E50000–0E5FFFF
728000–72FFFF
SA185
0 1 0 1 1 1 0 0 1
0B90000–0B9FFFF
5C8000–5CFFFF
SA230 0 1 1 1 0 0 1 1 0 0E60000–0E6FFFF
730000–737FFF
SA186
0 1 0 1 1 1 0 1 0
0BA0000–0BAFFFF
5D0000–5D7FFF
SA231 0 1 1 1 0 0 1 1 1 0E70000–0E7FFFF
738000–73FFFF
SA187
0 1 0 1 1 1 0 1 1
0BB0000–0BBFFFF
5D8000–5DFFFF
SA232 0 1 1 1 0 1 0 0 0 0E80000–0E8FFFF
740000–747FFF
SA188
0 1 0 1 1 1 1 0 0 0BC0000–0BCFFFF
5E0000–5E7FFF
SA233 0 1 1 1 0 1 0 0 1 0E90000–0E9FFFF
748000–74FFFF
SA189
0 1 0 1 1 1 1 0 1 0BD0000–0BDFFFF
5E8000–5EFFFF
SA234 0 1 1 1 0 1 0 1 0 0EA0000–0EAFFFF
750000–757FFF
Sector
Sector
Table 16.
S h e e t
A23–A15
8-bit
Address
Range
16-bit
Address
Range
SA190
0 1 0 1 1 1 1 1 0
0BE0000–0BEFFFF
5F0000–5F7FFF
SA235 0 1 1 1 0 1 0 1 1 0EB0000–0EBFFFF
758000–75FFFF
SA191
0 1 0 1 1 1 1 1 1
0BF0000–0BFFFFF
5F8000–5FFFFF
SA236 0 1 1 1 0 1 1 0 0 0EC0000–0ECFFFF
760000–767FFF
SA192
0 1 1 0 0 0 0 0 0
0C00000–0C0FFFF
600000–607FFF
SA237 0 1 1 1 0 1 1 0 1 0ED0000–0EDFFFF
768000–76FFFF
SA193
0 1 1 0 0 0 0 0 1
0C10000–0C1FFFF
608000–60FFFF
SA238 0 1 1 1 0 1 1 1 0 0EE0000–0EEFFFF
770000–777FFF
SA194
0 1 1 0 0 0 0 1 0
0C20000–0C2FFFF
610000–617FFF
SA239 0 1 1 1 0 1 1 1 1 0EF0000–0EFFFFF
778000–77FFFF
SA195
0 1 1 0 0 0 0 1 1
0C30000–0C3FFFF
618000–61FFFF
SA240 0 1 1 1 1 0 0 0 0 0F00000–0F0FFFF
780000–787FFF
SA196
0 1 1 0 0 0 1 0 0
0C40000–0C4FFFF
620000–627FFF
SA241 0 1 1 1 1 0 0 0 1 0F10000–0F1FFFF
788000–78FFFF
SA197
0 1 1 0 0 0 1 0 1
0C50000–0C5FFFF
628000–62FFFF
SA242 0 1 1 1 1 0 0 1 0 0F20000–0F2FFFF
790000–797FFF
SA198
0 1 1 0 0 0 1 1 0
0C60000–0C6FFFF
630000–637FFF
SA243 0 1 1 1 1 0 0 1 1 0F30000–0F3FFFF
798000–79FFFF
SA199
0 1 1 0 0 0 1 1 1
0C70000–0C7FFFF
638000–63FFFF
SA244 0 1 1 1 1 0 1 0 0 0F40000–0F4FFFF
7A0000–7A7FFF
SA200
0 1 1 0 0 1 0 0 0
0C80000–0C8FFFF
640000–647FFF
SA245 0 1 1 1 1 0 1 0 1 0F50000–0F5FFFF
7A8000–7AFFFF
SA201
0 1 1 0 0 1 0 0 1
0C90000–0C9FFFF
648000–64FFFF
SA246 0 1 1 1 1 0 1 1 0 0F60000–0F6FFFF
7B0000–7B7FFF
SA202
0 1 1 0 0 1 0 1 0
0CA0000–0CAFFFF
650000–657FFF
SA247 0 1 1 1 1 0 1 1 1 0F70000–0F7FFFF
7B8000–7BFFFF
SA203
0 1 1 0 0 1 0 1 1 0CB0000–0CBFFFF
658000–65FFFF
SA248 0 1 1 1 1 1 0 0 0 0F80000–0F8FFFF
7C0000–7C7FFF
SA204
0 1 1 0 0 1 1 0 0 0CC0000–0CCFFFF
660000–667FFF
SA249 0 1 1 1 1 1 0 0 1 0F90000–0F9FFFF
7C8000–7CFFFF
SA205
0 1 1 0 0 1 1 0 1 0CD0000–0CDFFFF
668000–66FFFF
SA250 0 1 1 1 1 1 0 1 0 0FA0000–0FAFFFF
7D0000–7D7FFF
SA206
0 1 1 0 0 1 1 1 0
0CE0000–0CEFFFF
670000–677FFF
SA251 0 1 1 1 1 1 0 1 1 0FB0000–0FBFFFF
7D8000–7DFFFF
SA207
0 1 1 0 0 1 1 1 1
0CF0000–0CFFFFF
678000–67FFFF
SA252 0 1 1 1 1 1 1 0 0 0FC0000–0FCFFFF
7E0000–7E7FFF
SA208
0 1 1 0 1 0 0 0 0 0D00000–0D0FFFF
680000–687FFF
SA253 0 1 1 1 1 1 1 0 1 0FD0000–0FDFFFF
7E8000–7EFFFF
7F0000–7F7FFF
SA209
0 1 1 0 1 0 0 0 1 0D10000–0D1FFFF
688000–68FFFF
SA254 0 1 1 1 1 1 1 1 0 0FE0000–0FEFFFF
SA210
0 1 1 0 1 0 0 1 0 0D20000–0D2FFFF
690000–697FFF
SA255 0 1 1 1 1 1 1 1 1 0FF0000–0FFFFFF
7F8000–7FFFFF
SA211
0 1 1 0 1 0 0 1 1 0D30000–0D3FFFF
698000–69FFFF
SA256 1 0 0 0 0 0 0 0 0 1000000–100FFFF
800000–807FFF
SA212
0 1 1 0 1 0 1 0 0 0D40000–0D4FFFF
6A0000–6A7FFF
SA257 1 0 0 0 0 0 0 0 1 1010000–101FFFF
808000–80FFFF
SA213
0 1 1 0 1 0 1 0 1 0D50000–0D5FFFF
6A8000–6AFFFF
SA258 1 0 0 0 0 0 0 1 0 1020000–102FFFF
810000–817FFF
SA214
0 1 1 0 1 0 1 1 0 0D60000–0D6FFFF
6B0000–6B7FFF
SA259 1 0 0 0 0 0 0 1 1 1030000–103FFFF
818000–81FFFF
SA215
0 1 1 0 1 0 1 1 1 0D70000–0D7FFFF
6B8000–6BFFFF
SA260 1 0 0 0 0 0 1 0 0 1040000–104FFFF
820000–827FFF
SA216
0 1 1 0 1 1 0 0 0 0D80000–0D8FFFF
6C0000–6C7FFF
SA261 1 0 0 0 0 0 1 0 1 1050000–105FFFF
828000–82FFFF
830000–837FFF
SA217
0 1 1 0 1 1 0 0 1 0D90000–0D9FFFF
6C8000–6CFFFF
SA262 1 0 0 0 0 0 1 1 0 1060000–106FFFF
SA218
0 1 1 0 1 1 0 1 0 0DA0000–0DAFFFF
6D0000–6D7FFF
SA263 1 0 0 0 0 0 1 1 1 1070000–107FFFF
838000–83FFFF
SA219
0 1 1 0 1 1 0 1 1 0DB0000–0DBFFFF
6D8000–6DFFFF
SA264 1 0 0 0 0 1 0 0 0 1080000–108FFFF
840000–847FFF
SA220
0 1 1 0 1 1 1 0 0 0DC0000–0DCFFFF
6E0000–6E7FFF
SA265 1 0 0 0 0 1 0 0 1 1090000–109FFFF
848000–84FFFF
SA221
0 1 1 0 1 1 1 0 1 0DD0000–0DDFFFF
6E8000–6EFFFF
SA266 1 0 0 0 0 1 0 1 0 10A0000–10AFFFF
850000–857FFF
SA222
0 1 1 0 1 1 1 1 0 0DE0000–0DEFFFF
6F0000–6F7FFF
SA267 1 0 0 0 0 1 0 1 1 10B0000–10BFFFF
858000–85FFFF
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
43
D a t a
Table 16.
S h e e t
S29GL256M Sector Address Table (Sheet 4 of 6)
16-bit
Address
Range
SA268
1 0 0 0 0 1 1 0 0
10C0000–10CFFFF
860000–867FFF
SA313 1 0 0 1 1 1 0 0 1 1390000–139FFFF
9C8000–9CFFFF
SA269
1 0 0 0 0 1 1 0 1 10D0000–10DFFFF
868000–86FFFF
SA314 1 0 0 1 1 1 0 1 0 13A0000–13AFFFF
9D0000–9D7FFF
Sector
8-bit
Address
Range
Sector
A23–A15
A23–A15
8-bit
Address
Range
16-bit
Address
Range
SA270
1 0 0 0 0 1 1 1 0
10E0000–10EFFFF
870000–877FFF
SA315 1 0 0 1 1 1 0 1 1 13B0000–13BFFFF
9D8000–9DFFFF
SA271
1 0 0 0 0 1 1 1 1
10F0000–10FFFFF
878000–87FFFF
SA316 1 0 0 1 1 1 1 0 0 13C0000–13CFFFF
9E0000–9E7FFF
SA272
1 0 0 0 1 0 0 0 0
1100000–110FFFF
880000–887FFF
SA317 1 0 0 1 1 1 1 0 1 13D0000–13DFFFF
9E8000–9EFFFF
SA273
1 0 0 0 1 0 0 0 1
1110000–111FFFF
888000–88FFFF
SA318 1 0 0 1 1 1 1 1 0 13E0000–13EFFFF
9F0000–9F7FFF
SA274
1 0 0 0 1 0 0 1 0
1120000–112FFFF
890000–897FFF
SA319 1 0 0 1 1 1 1 1 1 13F0000–13FFFFF
9F8000–9FFFFF
SA275
1 0 0 0 1 0 0 1 1
1130000–113FFFF
898000–89FFFF
SA320 1 0 1 0 0 0 0 0 0 1400000–140FFFF
A00000–A07FFF
SA276
1 0 0 0 1 0 1 0 0
1140000–114FFFF
8A0000–8A7FFF
SA321 1 0 1 0 0 0 0 0 1 1410000–141FFFF
A08000–A0FFFF
SA277
1 0 0 0 1 0 1 0 1
1150000–115FFFF
8A8000–8AFFFF
SA322 1 0 1 0 0 0 0 1 0 1420000–142FFFF
A10000–A17FFF
SA278
1 0 0 0 1 0 1 1 0
1160000–116FFFF
8B0000–8B7FFF
SA323 1 0 1 0 0 0 0 1 1 1430000–143FFFF
A18000–A1FFFF
SA279
1 0 0 0 1 0 1 1 1
1170000–117FFFF
8B8000–8BFFFF
SA324 1 0 1 0 0 0 1 0 0 1440000–144FFFF
A20000–A27FFF
SA280
1 0 0 0 1 1 0 0 0
1180000–118FFFF
8C0000–8C7FFF
SA325 1 0 1 0 0 0 1 0 1 1450000–145FFFF
A28000–A2FFFF
SA281
1 0 0 0 1 1 0 0 1
1190000–119FFFF
8C8000–8CFFFF
SA326 1 0 1 0 0 0 1 1 0 1460000–146FFFF
A30000–A37FFF
SA282
1 0 0 0 1 1 0 1 0
11A0000–11AFFFF
8D0000–8D7FFF
SA327 1 0 1 0 0 0 1 1 1 1470000–147FFFF
A38000–A3FFFF
A40000–A47FFF
SA283
1 0 0 0 1 1 0 1 1
11B0000–11BFFFF
8D8000–8DFFFF
SA328 1 0 1 0 0 1 0 0 0 1480000–148FFFF
SA284
1 0 0 0 1 1 1 0 0
11C0000–11CFFFF
8E0000–8E7FFF
SA329 1 0 1 0 0 1 0 0 1 1490000–149FFFF
A48000–A4FFFF
SA285
1 0 0 0 1 1 1 0 1 11D0000–11DFFFF
8E8000–8EFFFF
SA330 1 0 1 0 0 1 0 1 0 14A0000–14AFFFF
A50000–A57FFF
SA286
1 0 0 0 1 1 1 1 0
11E0000–11EFFFF
8F0000–8F7FFF
SA331 1 0 1 0 0 1 0 1 1 14B0000–14BFFFF
A58000–A5FFFF
SA287
1 0 0 0 1 1 1 1 1
11F0000–11FFFFF
8F8000–8FFFFF
SA332 1 0 1 0 0 1 1 0 0 14C0000–14CFFFF
A60000–A67FFF
SA288
1 0 0 1 0 0 0 0 0
1200000–120FFFF
900000–907FFF
SA333 1 0 1 0 0 1 1 0 1 14D0000–14DFFFF
A68000–A6FFFF
SA289
1 0 0 1 0 0 0 0 1
1210000–121FFFF
908000–90FFFF
SA334 1 0 1 0 0 1 1 1 0 14E0000–14EFFFF
A70000–A77FFF
SA290
1 0 0 1 0 0 0 1 0
1220000–122FFFF
910000–917FFF
SA335 1 0 1 0 0 1 1 1 1 14F0000–14FFFFF
A78000–A7FFFF
SA291
1 0 0 1 0 0 0 1 1
1230000–123FFFF
918000–91FFFF
SA336 1 0 1 0 1 0 0 0 0 1500000–150FFFF
A80000–A87FFF
SA292
1 0 0 1 0 0 1 0 0
1240000–124FFFF
920000–927FFF
SA337 1 0 1 0 1 0 0 0 1 1510000–151FFFF
A88000–A8FFFF
SA293
1 0 0 1 0 0 1 0 1
1250000–125FFFF
928000–92FFFF
SA338 1 0 1 0 1 0 0 1 0 1520000–152FFFF
A90000–A97FFF
SA294
1 0 0 1 0 0 1 1 0
1260000–126FFFF
930000–937FFF
SA339 1 0 1 0 1 0 0 1 1 1530000–153FFFF
A98000–A9FFFF
SA295
1 0 0 1 0 0 1 1 1
1270000–127FFFF
938000–93FFFF
SA340 1 0 1 0 1 0 1 0 0 1540000–154FFFF
AA0000–AA7FFF
SA296
1 0 0 1 0 1 0 0 0
1280000–128FFFF
940000–947FFF
SA341 1 0 1 0 1 0 1 0 1 1550000–155FFFF
AA8000–AAFFFF
SA297
1 0 0 1 0 1 0 0 1
1290000–129FFFF
948000–94FFFF
SA342 1 0 1 0 1 0 1 1 0 1560000–156FFFF
AB0000–AB7FFF
SA298
1 0 0 1 0 1 0 1 0
12A0000–12AFFFF
950000–957FFF
SA343 1 0 1 0 1 0 1 1 1 1570000–157FFFF
AB8000–ABFFFF
AC0000–AC7FFF
SA299
1 0 0 1 0 1 0 1 1
12B0000–12BFFFF
958000–95FFFF
SA344 1 0 1 0 1 1 0 0 0 1580000–158FFFF
SA300
1 0 0 1 0 1 1 0 0
12C0000–12CFFFF
960000–967FFF
SA345 1 0 1 0 1 1 0 0 1 1590000–159FFFF
AC8000–ACFFFF
SA301
1 0 0 1 0 1 1 0 1 12D0000–12DFFFF
968000–96FFFF
SA346 1 0 1 0 1 1 0 1 0 15A0000–15AFFFF
AD0000–AD7FFF
SA302
1 0 0 1 0 1 1 1 0
12E0000–12EFFFF
970000–977FFF
SA347 1 0 1 0 1 1 0 1 1 15B0000–15BFFFF
AD8000–ADFFFF
SA303
1 0 0 1 0 1 1 1 1
12F0000–12FFFFF
978000–97FFFF
SA348 1 0 1 0 1 1 1 0 0 15C0000–15CFFFF
AE0000–AE7FFF
SA304
1 0 0 1 1 0 0 0 0
1300000–130FFFF
980000–987FFF
SA349 1 0 1 0 1 1 1 0 1 15D0000–15DFFFF
AE8000–AEFFFF
SA305
1 0 0 1 1 0 0 0 1
1310000–131FFFF
988000–98FFFF
SA350 1 0 1 0 1 1 1 1 0 15E0000–15EFFFF
AF0000–AF7FFF
SA306
1 0 0 1 1 0 0 1 0
1320000–132FFFF
990000–997FFF
SA351 1 0 1 0 1 1 1 1 1 15F0000–15FFFFF
AF8000–AFFFFF
B00000–B07FFF
SA307
1 0 0 1 1 0 0 1 1
1330000–133FFFF
998000–99FFFF
SA352 1 0 1 1 0 0 0 0 0 1600000–160FFFF
SA308
1 0 0 1 1 0 1 0 0
1340000–134FFFF
9A0000–9A7FFF
SA353 1 0 1 1 0 0 0 0 1 1610000–161FFFF
B08000–B0FFFF
SA309
1 0 0 1 1 0 1 0 1
1350000–135FFFF
9A8000–9AFFFF
SA354 1 0 1 1 0 0 0 1 0 1620000–162FFFF
B10000–B17FFF
SA310
1 0 0 1 1 0 1 1 0
1360000–136FFFF
9B0000–9B7FFF
SA355 1 0 1 1 0 0 0 1 1 1630000–163FFFF
B18000–B1FFFF
SA311
1 0 0 1 1 0 1 1 1
1370000–137FFFF
9B8000–9BFFFF
SA356 1 0 1 1 0 0 1 0 0 1640000–164FFFF
B20000–B27FFF
SA312
1 0 0 1 1 1 0 0 0
1380000–138FFFF
9C0000–9C7FFF
SA357 1 0 1 1 0 0 1 0 1 1650000–165FFFF
B28000–B2FFFF
44
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S29GL256M Sector Address Table (Sheet 5 of 6)
A23–A15
8-bit
Address
Range
16-bit
Address
Range
SA358
1 0 1 1 0 0 1 1 0
1660000–166FFFF
B30000–B37FFF
SA403 1 1 0 0 1 0 0 1 1 1930000–193FFFF
C98000–C9FFFF
SA359
1 0 1 1 0 0 1 1 1
1670000–167FFFF
B38000–B3FFFF
SA404 1 1 0 0 1 0 1 0 0 1940000–194FFFF
CA0000–CA7FFF
SA360
1 0 1 1 0 1 0 0 0
1680000–168FFFF
B40000–B47FFF
SA405 1 1 0 0 1 0 1 0 1 1950000–195FFFF
CA8000–CAFFFF
SA361
1 0 1 1 0 1 0 0 1
1690000–169FFFF
B48000–B4FFFF
SA406 1 1 0 0 1 0 1 1 0 1960000–196FFFF
CB0000–CB7FFF
Sector
Sector
Table 16.
S h e e t
A23–A15
8-bit
Address
Range
16-bit
Address
Range
SA362
1 0 1 1 0 1 0 1 0
16A0000–16AFFFF
B50000–B57FFF
SA407 1 1 0 0 1 0 1 1 1 1970000–197FFFF
CB8000–CBFFFF
SA363
1 0 1 1 0 1 0 1 1
16B0000–16BFFFF
B58000–B5FFFF
SA408 1 1 0 0 1 1 0 0 0 1980000–198FFFF
CC0000–CC7FFF
SA364
1 0 1 1 0 1 1 0 0
16C0000–16CFFFF
B60000–B67FFF
SA409 1 1 0 0 1 1 0 0 1 1990000–199FFFF
CC8000–CCFFFF
SA365
1 0 1 1 0 1 1 0 1 16D0000–16DFFFF
B68000–B6FFFF
SA410 1 1 0 0 1 1 0 1 0 19A0000–19AFFFF
CD0000–CD7FFF
SA366
1 0 1 1 0 1 1 1 0
16E0000–16EFFFF
B70000–B77FFF
SA411 1 1 0 0 1 1 0 1 1 19B0000–19BFFFF
CD8000–CDFFFF
SA367
1 0 1 1 0 1 1 1 1
16F0000–16FFFFF
B78000–B7FFFF
SA412 1 1 0 0 1 1 1 0 0 19C0000–19CFFFF
CE0000–CE7FFF
SA368
1 0 1 1 1 0 0 0 0
1700000–170FFFF
B80000–B87FFF
SA413 1 1 0 0 1 1 1 0 1 19D0000–19DFFFF
CE8000–CEFFFF
SA369
1 0 1 1 1 0 0 0 1
1710000–171FFFF
B88000–B8FFFF
SA414 1 1 0 0 1 1 1 1 0 19E0000–19EFFFF
CF0000–CF7FFF
SA370
1 0 1 1 1 0 0 1 0
1720000–172FFFF
B90000–B97FFF
SA415 1 1 0 0 1 1 1 1 1 19F0000–19FFFFF
CF8000–CFFFFF
SA371
1 0 1 1 1 0 0 1 1
1730000–173FFFF
B98000–B9FFFF
SA416 1 1 0 1 0 0 0 0 0 1A00000–1A0FFFF
D00000–D07FFF
SA372
1 0 1 1 1 0 1 0 0
1740000–174FFFF
BA0000–BA7FFF
SA417 1 1 0 1 0 0 0 0 1 1A10000–1A1FFFF
D08000–D0FFFF
SA373
1 0 1 1 1 0 1 0 1
1750000–175FFFF
BA8000–BAFFFF
SA418 1 1 0 1 0 0 0 1 0 1A20000–1A2FFFF
D10000–D17FFF
SA374
1 0 1 1 1 0 1 1 0
1760000–176FFFF
BB0000–BB7FFF
SA419 1 1 0 1 0 0 0 1 1 1A30000–1A3FFFF
D18000–D1FFFF
SA375
1 0 1 1 1 0 1 1 1
1770000–177FFFF
BB8000–BBFFFF
SA420 1 1 0 1 0 0 1 0 0 1A40000–1A4FFFF
D20000–D27FFF
SA376
1 0 1 1 1 1 0 0 0
1780000–178FFFF
BC0000–BC7FFF
SA421 1 1 0 1 0 0 1 0 1 1A50000–1A5FFFF
D28000–D2FFFF
SA377
1 0 1 1 1 1 0 0 1
1790000–179FFFF
BC8000–BCFFFF
SA422 1 1 0 1 0 0 1 1 0 1A60000–1A6FFFF
D30000–D37FFF
SA378
1 0 1 1 1 1 0 1 0
17A0000–17AFFFF
BD0000–BD7FFF
SA423 1 1 0 1 0 0 1 1 1 1A70000–1A7FFFF
D38000–D3FFFF
SA379
1 0 1 1 1 1 0 1 1
17B0000–17BFFFF
BD8000–BDFFFF
SA424 1 1 0 1 0 1 0 0 0 1A80000–1A8FFFF
D40000–D47FFF
SA380
1 0 1 1 1 1 1 0 0
17C0000–17CFFFF
BE0000–BE7FFF
SA425 1 1 0 1 0 1 0 0 1 1A90000–1A9FFFF
D48000–D4FFFF
D50000–D57FFF
SA381
1 0 1 1 1 1 1 0 1 17D0000–17DFFFF
BE8000–BEFFFF
SA426 1 1 0 1 0 1 0 1 0 1AA0000–1AAFFFF
SA382
1 0 1 1 1 1 1 1 0
17E0000–17EFFFF
BF0000–BF7FFF
SA427 1 1 0 1 0 1 0 1 1 1AB0000–1ABFFFF
D58000–D5FFFF
SA383
1 0 1 1 1 1 1 1 1
17F0000–17FFFFF
BF8000–BFFFFF
SA428 1 1 0 1 0 1 1 0 0 1AC0000–1ACFFFF
D60000–D67FFF
SA384
1 1 0 0 0 0 0 0 0
1800000–180FFFF
C00000–C07FFF
SA429 1 1 0 1 0 1 1 0 1 1AD0000–1ADFFFF
D68000–D6FFFF
SA385
1 1 0 0 0 0 0 0 1
1810000–181FFFF
C08000–C0FFFF
SA430 1 1 0 1 0 1 1 1 0 1AE0000–1AEFFFF
D70000–D77FFF
SA386
1 1 0 0 0 0 0 1 0
1820000–182FFFF
C10000–C17FFF
SA431 1 1 0 1 0 1 1 1 1 1AF0000–1AFFFFF
D78000–D7FFFF
SA387
1 1 0 0 0 0 0 1 1
1830000–183FFFF
C18000–C1FFFF
SA432 1 1 0 1 1 0 0 0 0 1B00000–1B0FFFF
D80000–D87FFF
SA388
1 1 0 0 0 0 1 0 0
1840000–184FFFF
C20000–C27FFF
SA433 1 1 0 1 1 0 0 0 1 1B10000–1B1FFFF
D88000–D8FFFF
D90000–D97FFF
SA389
1 1 0 0 0 0 1 0 1
1850000–185FFFF
C28000–C2FFFF
SA434 1 1 0 1 1 0 0 1 0 1B20000–1B2FFFF
SA390
1 1 0 0 0 0 1 1 0
1860000–186FFFF
C30000–C37FFF
SA435 1 1 0 1 1 0 0 1 1 1B30000–1B3FFFF
D98000–D9FFFF
SA391
1 1 0 0 0 0 1 1 1
1870000–187FFFF
C38000–C3FFFF
SA436 1 1 0 1 1 0 1 0 0 1B40000–1B4FFFF
DA0000–DA7FFF
SA392
1 1 0 0 0 1 0 0 0
1880000–188FFFF
C40000–C47FFF
SA437 1 1 0 1 1 0 1 0 1 1B50000–1B5FFFF
DA8000–DAFFFF
SA393
1 1 0 0 0 1 0 0 1
1890000–189FFFF
C48000–C4FFFF
SA438 1 1 0 1 1 0 1 1 0 1B60000–1B6FFFF
DB0000–DB7FFF
SA394
1 1 0 0 0 1 0 1 0
18A0000–18AFFFF
C50000–C57FFF
SA439 1 1 0 1 1 0 1 1 1 1B70000–1B7FFFF
DB8000–DBFFFF
SA395
1 1 0 0 0 1 0 1 1
18B0000–18BFFFF
C58000–C5FFFF
SA440 1 1 0 1 1 1 0 0 0 1B80000–1B8FFFF
DC0000–DC7FFF
SA396
1 1 0 0 0 1 1 0 0
18C0000–18CFFFF
C60000–C67FFF
SA441 1 1 0 1 1 1 0 0 1 1B90000–1B9FFFF
DC8000–DCFFFF
SA397
1 1 0 0 0 1 1 0 1 18D0000–18DFFFF
C68000–C6FFFF
SA442 1 1 0 1 1 1 0 1 0 1BA0000–1BAFFFF
DD0000–DD7FFF
SA398
1 1 0 0 0 1 1 1 0
18E0000–18EFFFF
C70000–C77FFF
SA443 1 1 0 1 1 1 0 1 1 1BB0000–1BBFFFF
DD8000–DDFFFF
SA399
1 1 0 0 0 1 1 1 1
18F0000–18FFFFF
C78000–C7FFFF
SA444 1 1 0 1 1 1 1 0 0 1BC0000–1BCFFFF
DE0000–DE7FFF
SA400
1 1 0 0 1 0 0 0 0
1900000–190FFFF
C80000–C87FFF
SA445 1 1 0 1 1 1 1 0 1 1BD0000–1BDFFFF
DE8000–DEFFFF
SA401
1 1 0 0 1 0 0 0 1
1910000–191FFFF
C88000–C8FFFF
SA446 1 1 0 1 1 1 1 1 0 1BE0000–1BEFFFF
DF0000–DF7FFF
SA402
1 1 0 0 1 0 0 1 0
1920000–192FFFF
C90000–C97FFF
SA447 1 1 0 1 1 1 1 1 1 1BF0000–1BFFFFF
DF8000–DFFFFF
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
45
D a t a
S29GL256M Sector Address Table (Sheet 6 of 6)
A23–A15
8-bit
Address
Range
16-bit
Address
Range
SA448
1 1 1 0 0 0 0 0 0
1C00000–1C0FFFF
E00000–E07FFF
SA480 1 1 1 1 0 0 0 0 0 1E00000–1E0FFFF
F00000–F07FFF
SA449
1 1 1 0 0 0 0 0 1
1C10000–1C1FFFF
E08000–E0FFFF
SA481 1 1 1 1 0 0 0 0 1 1E10000–1E1FFFF
F08000–F0FFFF
SA450
1 1 1 0 0 0 0 1 0
1C20000–1C2FFFF
E10000–E17FFF
SA482 1 1 1 1 0 0 0 1 0 1E20000–1E2FFFF
F10000–F17FFF
SA451
1 1 1 0 0 0 0 1 1
1C30000–1C3FFFF
E18000–E1FFFF
SA483 1 1 1 1 0 0 0 1 1 1E30000–1E3FFFF
F18000–F1FFFF
SA452
1 1 1 0 0 0 1 0 0
1C40000–1C4FFFF
E20000–E27FFF
SA484 1 1 1 1 0 0 1 0 0 1E40000–1E4FFFF
F20000–F27FFF
SA453
1 1 1 0 0 0 1 0 1
1C50000–1C5FFFF
E28000–E2FFFF
SA485 1 1 1 1 0 0 1 0 1 1E50000–1E5FFFF
F28000–F2FFFF
SA454
1 1 1 0 0 0 1 1 0
1C60000–1C6FFFF
E30000–E37FFF
SA486 1 1 1 1 0 0 1 1 0 1E60000–1E6FFFF
F30000–F37FFF
SA455
1 1 1 0 0 0 1 1 1
1C70000–1C7FFFF
E38000–E3FFFF
SA487 1 1 1 1 0 0 1 1 1 1E70000–1E7FFFF
F38000–F3FFFF
SA456
1 1 1 0 0 1 0 0 0
1C80000–1C8FFFF
E40000–E47FFF
SA488 1 1 1 1 0 1 0 0 0 1E80000–1E8FFFF
F40000–F47FFF
SA457
1 1 1 0 0 1 0 0 1
1C90000–1C9FFFF
E48000–E4FFFF
SA489 1 1 1 1 0 1 0 0 1 1E90000–1E9FFFF
F48000–F4FFFF
SA458
1 1 1 0 0 1 0 1 0
1CA0000–1CAFFFF
E50000–E57FFF
SA490 1 1 1 1 0 1 0 1 0 1EA0000–1EAFFFF
F50000–F57FFF
SA459
1 1 1 0 0 1 0 1 1 1CB0000–1CBFFFF
E58000–E5FFFF
SA491 1 1 1 1 0 1 0 1 1 1EB0000–1EBFFFF
F58000–F5FFFF
F60000–F67FFF
Sector
Sector
Table 16.
S h e e t
A23–A15
8-bit
Address
Range
16-bit
Address
Range
SA460
1 1 1 0 0 1 1 0 0 1CC0000–1CCFFFF
E60000–E67FFF
SA492 1 1 1 1 0 1 1 0 0 1EC0000–1ECFFFF
SA461
1 1 1 0 0 1 1 0 1 1CD0000–1CDFFFF
E68000–E6FFFF
SA493 1 1 1 1 0 1 1 0 1 1ED0000–1EDFFFF
F68000–F6FFFF
SA462
1 1 1 0 0 1 1 1 0
1CE0000–1CEFFFF
E70000–E77FFF
SA494 1 1 1 1 0 1 1 1 0 1EE0000–1EEFFFF
F70000–F77FFF
SA463
1 1 1 0 0 1 1 1 1
1CF0000–1CFFFFF
E78000–E7FFFF
SA495 1 1 1 1 0 1 1 1 1 1EF0000–1EFFFFF
F78000–F7FFFF
SA464
1 1 1 0 1 0 0 0 0 1D00000–1D0FFFF
E80000–E87FFF
SA496 1 1 1 1 1 0 0 0 0 1F00000–1F0FFFF
F80000–F87FFF
SA465
1 1 1 0 1 0 0 0 1 1D10000–1D1FFFF
E88000–E8FFFF
SA497 1 1 1 1 1 0 0 0 1 1F10000–1F1FFFF
F88000–F8FFFF
SA466
1 1 1 0 1 0 0 1 0 1D20000–1D2FFFF
E90000–E97FFF
SA498 1 1 1 1 1 0 0 1 0 1F20000–1F2FFFF
F90000–F97FFF
SA467
1 1 1 0 1 0 0 1 1 1D30000–1D3FFFF
E98000–E9FFFF
SA499 1 1 1 1 1 0 0 1 1 1F30000–1F3FFFF
F98000–F9FFFF
SA468
1 1 1 0 1 0 1 0 0 1D40000–1D4FFFF
EA0000–EA7FFF
SA500 1 1 1 1 1 0 1 0 0 1F40000–1F4FFFF
FA0000–FA7FFF
SA469
1 1 1 0 1 0 1 0 1 1D50000–1D5FFFF
EA8000–EAFFFF
SA501 1 1 1 1 1 0 1 0 1 1F50000–1F5FFFF
FA8000–FAFFFF
SA470
1 1 1 0 1 0 1 1 0 1D60000–1D6FFFF
EB0000–EB7FFF
SA502 1 1 1 1 1 0 1 1 0 1F60000–1F6FFFF
FB0000–FB7FFF
SA471
1 1 1 0 1 0 1 1 1 1D70000–1D7FFFF
EB8000–EBFFFF
SA503 1 1 1 1 1 0 1 1 1 1F70000–1F7FFFF
FB8000–FBFFFF
SA472
1 1 1 0 1 1 0 0 0 1D80000–1D8FFFF
EC0000–EC7FFF
SA504 1 1 1 1 1 1 0 0 0 1F80000–1F8FFFF
FC0000–FC7FFF
SA473
1 1 1 0 1 1 0 0 1 1D90000–1D9FFFF
EC8000–ECFFFF
SA505 1 1 1 1 1 1 0 0 1 1F90000–1F9FFFF
FC8000–FCFFFF
SA474
1 1 1 0 1 1 0 1 0 1DA0000–1DAFFFF
ED0000–ED7FFF
SA506 1 1 1 1 1 1 0 1 0 1FA0000–1FAFFFF
FD0000–FD7FFF
SA475
1 1 1 0 1 1 0 1 1 1DB0000–1DBFFFF
ED8000–EDFFFF
SA507 1 1 1 1 1 1 0 1 1 1FB0000–1FBFFFF
FD8000–FDFFFF
SA476
1 1 1 0 1 1 1 0 0 1DC0000–1DCFFFF
EE0000–EE7FFF
SA508 1 1 1 1 1 1 1 0 0 1FC0000–1FCFFFF
FE0000–FE7FFF
SA477
1 1 1 0 1 1 1 0 1 1DD0000–1DDFFFF
EE8000–EEFFFF
SA509 1 1 1 1 1 1 1 0 1 1FD0000–1FDFFFF
FE8000–FEFFFF
SA478
1 1 1 0 1 1 1 1 0 1DE0000–1DEFFFF
EF0000–EF7FFF
SA510 1 1 1 1 1 1 1 1 0 1FE0000–1FEFFFF
FF0000–FF7FFF
SA479
1 1 1 0 1 1 1 1 1
EF8000–EFFFFF
SA511 1 1 1 1 1 1 1 1 1 1FF0000–1FFFFFF
FF8000–FFFFFF
1DF0000–1DFFFFF
Note: All sectors are 64 Kbytes or 32 Kwords in size.
46
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Autoselect Mode
The autoselect mode provides manufacturer and device identification, and sector group protection
verification, through identifier codes output on DQ7–DQ0. This mode is primarily intended for programming equipment to automatically match a device to be programmed with its corresponding
programming algorithm. However, the autoselect codes can also be accessed in-system through
the command register.
When using programming equipment, the autoselect mode requires VID on address pin A9. Address pins A6, A3, A2, A1, and A0 must be as shown in Table 17. In addition, when verifying sector
protection, the sector address must appear on the appropriate highest order address bits (see
Table 6 through Table 16). Table 17 shows the remaining address bits that are don’t care. When
all necessary bits are set as required, the programming equipment may then read the corresponding identifier code on DQ7–DQ0.
To access the autoselect codes in-system, the host system can issue the autoselect command via
the command register, as shown in Table 34 and Table 35. This method does not require VID. See
Autoselect Command Sequence for more information.
Table 17.
Description
S29GL128M S29GL256M
Manufacturer ID:
Spansion Products
CE# OE# WE#
L
L
H
A22 to
A15
X
Autoselect Codes, (High Voltage Method)
A1
A
A A
4
8
5 3
A
A
to A9 to
to to
6
1
A1
A
A A
0
7
4 2
X
VI
X
VI
L
X
L
X
S29GL064M
BYTE#
= VIL
00
X
Model Number
R1, R2,
R0
R8, R9
01
h
R5, R6,
R7
01h
01h
L
L
H
22
X
7Eh
H
H
L
22
X
12h
H
H
H
22
X
01h
L
L
H
22
X
7Eh
H
H
L
22
X
12h
H
H
H
22
X
00h
L
L
H
22
X
7E
h
7Eh
7Eh
7Eh
H
H
L
22
X
13
h
0Ch
10h
13h
Cycle 3
H
H
H
22
X
00
h
01h
00h (-R4,
bottom boot)
01h (-R3,
top boot)
01h
Cycle 1
L
L
H
22
X
7E
h
7Eh
7Eh
7Eh
H
H
L
22
X
1C
h
1Dh
1Ah
1Ah
H
H
H
22
X
00
h
00h
00h (-R4,
bottom boot)
01h (-R3,
top boot)
Cycle 1
Cycle 2
L
L
H
X
Cycle 3
D
X
L
Cycle 1
Cycle 2
L
L
H
X
X
Cycle 3
VI
D
X
L
X
Cycle 2
Cycle 2
L
L
L
L
H
H
X
X
X
X
VI
D
VI
D
X
X
L
L
X
X
Cycle 3
Sector Group
Protection
Verification
L
L
H
SA
X
VI
Secured Silicon
Sector Indicator
Bit (DQ7), WP#
protects highest
address sector
L
L
H
X
X
VI
Secured Silicon
Sector Indicator
Bit (DQ7), WP#
protects lowest
address sector
L
L
H
X
X
VI
D
D
D
01h
R3,R4
L
Cycle 1
S29GL032M
BYTE#
= VIH
L
D
X
A
0
DQ7 to DQ0
DQ8 to DQ15
X
L
X
L
H
L
X
X
01h (protected),
00h (unprotected)
X
L
X
L
H
H
X
X
98h (factory locked),
18h (not factory locked)
X
L
X
L
H
H
X
X
88h (factory locked),
08h (not factory locked)
Legend: L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don’t care.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
47
D a t a
S h e e t
Sector Group Protection and Unprotection
The hardware sector group protection feature disables both program and erase operations in any
sector group. In this device, a sector group consists of four adjacent sectors that are protected
or unprotected at the same time (see Table 4). The hardware sector group unprotection feature
re-enables both program and erase operations in previously protected sector groups. Sector
group protection/unprotection can be implemented via two methods.
Sector protection/unprotection requires VID on the RESET# pin only, and can be implemented either in-system or via programming equipment. Figure 2 shows the algorithms and Figure 24
shows the timing diagram. This method uses standard microprocessor bus cycle timing. For sector
group unprotect, all unprotected sector groups must first be protected prior to the first sector
group unprotect write cycle.
The device is shipped with all sector groups unprotected. Spansion offers the option of programming and protecting sector groups at its factory prior to shipping the device through Spansion
Programming Service. Contact a Spansion representative for details.
It is possible to determine whether a sector group is protected or unprotected. See Autoselect
Mode for details.
Table 18.
S29GL032M (Model R0) Sector Group Protection/Unprotection Addresses
Sector Group
A22–A18
Sector Group
A22–A18
Sector Group
A22–A18
Sector Group
A22–A18
SA0–SA3
00000
SA16–SA19
00100
SA32–SA35
01000
SA48–SA51
01100
SA4–SA7
00001
SA20–SA23
00101
SA36–SA39
01001
SA52–SA55
01101
SA8–SA11
00010
SA24–SA27
00110
SA40–SA43
01010
SA56–SA59
01110
SA12–SA15
00011
SA28–SA31
00111
SA44–SA47
01011
SA60–SA63
01111
Note: All sector groups are 256 Kwords in size.
Table 19. S29GL032M (Models R1, R2) Sector Group Protection/Unprotection Addresses
Sector Group
A20–A15
Sector Group
A20–A15
Sector Group
A20–A15
Sector Group
A20–A15
SA0
000000
SA12–SA15
0011xx
SA36–SA39
1001xx
SA56–SA59
1110xx
SA1
000001
SA16–SA19
0100xx
SA40–SA43
1010xx
SA60
111100
SA2
000010
SA20–SA23
0101xx
SA44–SA47
1011xx
SA61
111101
SA3
000011
SA24–SA27
0110xx
SA48–SA51
1100xx
SA62
111110
SA52–SA55
1101xx
SA63
111111
SA4–SA7
0001xx
SA28–SA31
0111xx
SA8–SA11
0010xx
SA32–SA35
1000xx
Table 20. S29GL032M (Model R3) Sector Group Protection/Unprotection Address Table
Sector
A20–A12
Sector/Sector
Block Size
(Kbytes)
Sector
A20–A12
Sector/Sector
Block Size
(Kbytes)
Sector
A20–A12
Sector/Sector
Block Size
(Kbytes)
SA0-SA3
0000XXXXXh
256 (4x64)
SA36–SA39
1001XXXXXh
256 (4x64)
SA63
111111000h
8
SA4-SA7
0001XXXXXh
256 (4x64)
SA40–SA43
1010XXXXXh
256 (4x64)
SA64
111111001h
8
SA8-SA11
0010XXXXXh
256 (4x64)
SA44–SA47
1011XXXXXh
256 (4x64)
SA65
111111010h
8
SA12-SA15
0011XXXXXh
256 (4x64)
SA48–SA51
1100XXXXXh
256 (4x64)
SA66
111111011h
8
SA16-SA19
0100XXXXXh
256 (4x64)
SA52-SA55
1101XXXXXh
256 (4x64)
SA67
111111100h
8
SA20-SA23
0101XXXXXh
256 (4x64)
SA56-SA59
1110XXXXXh
256 (4x64)
SA68
111111101h
8
SA69
111111110h
8
SA70
111111111h
8
SA24-SA27
0110XXXXXh
256 (4x64)
SA28-SA31
0111XXXXXh
256 (4x64)
SA32–SA35
1000XXXXXh
256 (4x64)
48
111100XXXh
SA60-SA62
111101XXXh
192 (3x64)
111110XXXh
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
Table 21.
S h e e t
S29GL032M (Model R4) Sector Group Protection/Unprotection Address Table
Sector
A20–A12
Sector/Sector
Block Size
(Kbytes)
SA0
000000000h
8
SA1
000000001h
8
SA2
000000010h
8
SA3
000000011h
SA4
SA5
Sector
A20–A12
Sector/Sector
Block Size
(Kbytes)
000001XXXh
A20–A12
SA35-SA38
0111XXXXXh
256 (4x64)
SA39-SA42
1000XXXXXh
256 (4x64)
SA43-SA46
1001XXXXXh
256 (4x64)
SA47-SA50
1010XXXXXh
256 (4x64)
SA8–SA10
000010XXXh
8
SA11–SA14
0001XXXXXh
256 (4x64)
000000100h
8
SA15–SA18
0010XXXXXh
256 (4x64)
SA51-SA54
1011XXXXXh
256 (4x64)
000000101h
8
SA19–SA22
0011XXXXXh
256 (4x64)
SA55–SA58
1100XXXXXh
256 (4x64)
SA6
000000110h
8
SA23–SA26
0100XXXXXh
256 (4x64)
SA59–SA62
1101XXXXXh
256 (4x64)
SA7
000000111h
8
l
192 (3x64)
Sector
000011XXXh
SA27-SA30
0101XXXXXh
256 (4x64)
SA63–SA66
1110XXXXXh
256 (4x64)
SA31-SA34
0110XXXXXh
256 (4x64)
SA67–SA70
1111XXXXXh
256 (4x64)
Table 22. S29GL064M (Model 00) Sector Group Protection/Unprotection Address Table
Sector Group
A22–A18
Sector Group
A22–A18
Sector Group
A22–A18
Sector Group
A22–A18
SA0–SA3
00000
SA36–SA39
01001
SA68–SA71
10001
SA100–SA103
11001
SA4–SA7
00001
SA40–SA43
01010
SA72–SA75
10010
SA104–SA107
11010
SA8–SA11
00010
SA44–SA47
01011
SA76–SA79
10011
SA108–SA111
11011
SA12–SA15
00011
SA48–SA51
01100
SA80–SA83
10100
SA112–SA115
11100
SA16–SA19
00100
SA52–SA55
01101
SA88–SA91
10110
SA116–SA119
11101
SA20–SA23
00101
SA56–SA59
01110
SA92–SA95
10111
SA120–SA123
11110
SA24–SA27
00110
SA60–SA63
01111
SA96–SA99
11000
SA124–SA127
11111
SA32–SA35
01000
SA64–SA67
10000
Note: All sector groups are 256 Kwords in size.
Table 23. S29GL064M (Models R1, R2, R8, R9) Sector Group Protection/Unprotection Addresses
Sector Group
A21–A15
Sector Group
A21–A15
Sector Group
A21–A15
Sector Group
A21–A15
SA0
0000000
SA28–SA31
00111xx
SA64–SA67
10000xx
SA104–SA107
11010xx
SA1
0000001
SA32–SA35
01000xx
SA68–SA71
10001xx
SA108–SA111
11011xx
SA2
0000010
SA36–SA39
01001xx
SA72–SA75
10010xx
SA112–SA115
11100xx
11101xx
SA3
0000011
SA40–SA43
01010xx
SA76–SA79
10011xx
SA116–SA119
SA4–SA7
00001xx
SA44–SA47
01011xx
SA80–SA83
10100xx
SA120–SA123
11110xx
SA8–SA11
00010xx
SA48–SA51
01100xx
SA84–SA87
10101xx
SA124
1111100
SA12–SA15
00011xx
SA52–SA55
01101xx
SA88–SA91
10110xx
SA125
1111101
SA16–SA19
00100xx
SA56–SA59
01110xx
SA92–SA95
10111xx
SA126
1111110
SA20–SA23
00101xx
SA60–SA63
01111xx
SA96–SA99
11000xx
SA127
1111111
SA24–SA27
00110xx
SA28–SA31
00111xx
SA100–SA103
11001xx
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
49
D a t a
S h e e t
Table 24. S29GL064M (Model R3) Sector Group Protection/Unprotection Address Table
Sector
A21–A12
Sector/ Sector
Block Size
(Kbytes)
Sector
A21–A12
Sector/ Sector
Block Size
(Kbytes)
SA0-SA3
00000XXXXX
256 (4x64)
SA56-SA59
01110XXXXX
256 (4x64)
SA112-SA115 11100XXXXX
256 (4x64)
SA4-SA7
00001XXXXX
256 (4x64)
SA60-SA63
01111XXXXX
256 (4x64)
SA116-SA119 11101XXXXX
256 (4x64)
SA8-SA11
00010XXXXX
256 (4x64)
SA64-SA67
10000XXXXX
256 (4x64)
SA120-SA123 11110XXXXX
256 (4x64)
Sector
A21–A12
Sector/ Sector
Block Size
(Kbytes)
SA12-SA15 00011XXXXX
256 (4x64)
SA68-SA71
10001XXXXX
256 (4x64)
SA16-SA19 00100XXXXX
256 (4x64)
SA72-SA75
10010XXXXX
256 (4x64)
1111100XXX
SA20-SA23 00101XXXXX
256 (4x64)
SA76-SA79
10011XXXXX
256 (4x64)
SA24-SA27 00110XXXXX
256 (4x64)
SA80-SA83
10100XXXXX
256 (4x64)
SA127
1111111000
8
SA28-SA31 00111XXXXX
256 (4x64)
SA84-SA87
10101XXXXX
256 (4x64)
SA128
1111111001
8
SA32-SA35 01000XXXXX
256 (4x64)
SA88-SA91
10110XXXXX
256 (4x64)
SA129
1111111010
8
SA36-SA39 01001XXXXX
256 (4x64)
SA92-SA95
10111XXXXX
256 (4x64)
SA130
1111111011
8
SA40-SA43 01010XXXXX
256 (4x64)
SA96-SA99
11000XXXXX
256 (4x64)
SA131
1111111100
8
SA44-SA47 01011XXXXX
256 (4x64)
SA100-SA103 11001XXXXX
256 (4x64)
SA132
1111111101
8
SA48-SA51 01100XXXXX
256 (4x64)
SA104-SA107 11010XXXXX
256 (4x64)
SA133
1111111110
8
SA52-SA55 01101XXXXX
256 (4x64)
SA108-SA111 11011XXXXX
256 (4x64)
SA134
1111111111
8
SA124-SA126
1111101XXX
192 (3x64)
1111110XXX
Table 25. S29GL064M (Model R4) Sector Group Protection/Unprotection Addresses
Sector
A21–A12
Sector/Sector
Block Size
(Kbytes)
Sector/Sector
Block Size
(Kbytes)
Sector
A21–A12
Sector/Sector
Block Size
(Kbytes)
SA0
0000000000
8
SA23–SA26 00100XXXXX
256 (4x64)
SA79–SA82
10010XXXXX
256 (4x64)
SA1
0000000001
SA2
0000000010
8
SA27-SA30 00101XXXXX
256 (4x64)
SA83–SA86
10011XXXXX
256 (4x64)
8
SA31-SA34 00110XXXXX
256 (4x64)
SA87–SA90
10100XXXXX
SA3
256 (4x64)
0000000011
8
SA35-SA38 00111XXXXX
256 (4x64)
SA91–SA94
10101XXXXX
256 (4x64)
SA4
0000000100
8
SA39-SA42 01000XXXXX
256 (4x64)
SA95–SA98
10110XXXXX
256 (4x64)
SA5
0000000101
8
SA43-SA46 01001XXXXX
256 (4x64)
SA99–SA102
10111XXXXX
256 (4x64)
SA6
0000000110
8
SA47-SA50 01010XXXXX
256 (4x64)
SA103–SA106 11000XXXXX
256 (4x64)
0000000111
8
SA7
0000001XXX
SA8–SA10
0000010XXX
192 (3x64)
0000011XXX
Sector
A21–A12
SA51-SA54 01011XXXXX
256 (4x64)
SA107–SA110 11001XXXXX
256 (4x64)
SA55–SA58 01100XXXXX
256 (4x64)
SA111–SA114 11010XXXXX
256 (4x64)
SA59–SA62 01101XXXXX
256 (4x64)
SA115–SA118 11011XXXXX
256 (4x64)
SA63–SA66 01110XXXXX
256 (4x64)
SA119–SA122 11100XXXXX
256 (4x64)
SA11–SA14 00001XXXXX
256 (4x64)
SA67–SA70 01111XXXXX
256 (4x64)
SA123–SA126 11101XXXXX
256 (4x64)
SA15–SA18 00010XXXXX
256 (4x64)
SA71–SA74 10000XXXXX
256 (4x64)
SA127–SA130 11110XXXXX
256 (4x64)
SA19–SA22 00011XXXXX
256 (4x64)
SA75–SA78 10001XXXXX
256 (4x64)
SA131–SA134 11111XXXXX
256 (4x64)
50
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Table 26. S29GL064M (Model R5) Sector Group Protection/Unprotection Addresses
Sector Group
A21–A17
Sector Group
A21–A17
Sector Group
A21–A17
Sector Group
A21–A17
Sector Group
A21–A17
SA0–SA3
00000
SA28–SA31
00111
SA56–SA59
01110
SA80–SA83
10100
SA104–SA107
11010
SA4–SA7
00001
SA32–SA35
01000
SA60–SA63
01111
SA84–SA87
10101
SA108–SA111
11011
SA8–SA11
00010
SA36–SA39
01001
SA64–SA67
10000
SA88–SA91
10110
SA112–SA115
11100
SA12–SA15
00011
SA40–SA43
01010
SA68–SA71
10001
SA92–SA95
10111
SA116–SA119
11101
SA16–SA19
00100
SA44–SA47
01011
SA72–SA75
10010
SA96–SA99
11000
SA120–SA123
11110
SA20–SA23
00101
SA48–SA51
01100
SA76–SA79
10011
SA100–SA103
11001
SA124–SA127
11111
SA24–SA27
00110
SA52–SA55
01101
Note: All sector groups are 128 Kwords in size.
Table 27. S29GL064M (Models R6, R7) Sector Group Protection/Unprotection Address
Sector Group
A21–A17
Sector Group
A21–A17
Sector Group
A21–A17
Sector Group
A21–A17
Sector Group
A21–A17
SA0–SA3
00000
SA28–SA31
00111
SA56–SA59
01110
SA80–SA83
10100
SA104–SA107
11010
SA4–SA7
00001
SA32–SA35
01000
SA60–SA63
01111
SA84–SA87
10101
SA108–SA111
11011
SA8–SA11
00010
SA36–SA39
01001
SA64–SA67
10000
SA88–SA91
10110
SA112–SA115
11100
SA12–SA15
00011
SA40–SA43
01010
SA68–SA71
10001
SA92–SA95
10111
SA116–SA119
11101
SA16–SA19
00100
SA44–SA47
01011
SA72–SA75
10010
SA96–SA99
11000
SA120–SA123
11110
SA20–SA23
00101
SA48–SA51
01100
SA76–SA79
10011
SA100–SA103
11001
SA124–SA127
11111
SA24–SA27
00110
SA52–SA55
01101
Note: All sector groups are 128 Kwords in size.
Table 28.
S29GL128M Sector Group Protection/Unprotection Addresses
Sector Group
A22–A15
Sector Group
A22–A15
Sector Group
A22–A15
Sector Group
A22–A15
SA0
00000000
SA72–SA75
010010xx
SA156–SA159
100111xx
SA240–SA243
111100xx
SA1
00000001
SA76–SA79
010011xx
SA160–SA163
101000xx
SA244–SA247
111101xx
SA2
00000010
SA80–SA83
010100xx
SA164–SA167
101001xx
SA248–SA251
111110xx
SA3
00000011
SA84–SA87
010101xx
SA168–SA171
101010xx
SA252
11111100
SA4–SA7
000001xx
SA88–SA91
010110xx
SA172–SA175
101011xx
SA253
11111101
SA8–SA11
000010xx
SA92–SA95
010111xx
SA176–SA179
101100xx
SA254
11111110
SA12–SA15
000011xx
SA96–SA99
011000xx
SA180–SA183
101101xx
SA255
11111111
SA16–SA19
000100xx
SA100–SA103
011001xx
SA184–SA187
101110xx
SA20–SA23
000101xx
SA104–SA107
011010xx
SA188–SA191
101111xx
SA24–SA27
000110xx
SA108–SA111
011011xx
SA192–SA195
110000xx
SA28–SA31
000111xx
SA112–SA115
011100xx
SA196–SA199
110001xx
SA32–SA35
001000xx
SA116–SA119
011101xx
SA200–SA203
110010xx
SA36–SA39
001001xx
SA120–SA123
011110xx
SA204–SA207
110011xx
SA40–SA43
001010xx
SA124–SA127
011111xx
SA208–SA211
110100xx
SA44–SA47
001011xx
SA128–SA131
100000xx
SA212–SA215
110101xx
SA48–SA51
001100xx
SA132–SA135
100001xx
SA216–SA219
110110xx
SA52–SA55
001101xx
SA136–SA139
100010xx
SA220–SA223
110111xx
SA56–SA59
001110xx
SA140–SA143
100011xx
SA224–SA227
111000xx
SA60–SA63
001111xx
SA144–SA147
100100xx
SA228–SA231
111001xx
SA64–SA67
010000xx
SA148–SA151
100101xx
SA232–SA235
111010xx
SA68–SA71
010001xx
SA152–SA155
100110xx
SA236–SA239
111011xx
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
51
D a t a
Table 29.
52
S h e e t
S29GL256M Sector Group Protection/Unprotection Addresses
Sector Group
A23–A15
Sector Group
A23–A15
Sector Group
A23–A15
Sector Group
A23–A15
SA0
000000000
SA124–SA127
0011111xx
SA260–SA263
1000001xx
SA392–SA395
1100010xx
SA1
000000001
SA128–SA131
0100000xx
SA264–SA267
1000010xx
SA396–SA399
1100011xx
SA2
000000010
SA132–SA135
0100001xx
SA268–SA271
1000011xx
SA400–SA403
1100100xx
SA3
000000011
SA136–SA139
0100010xx
SA276–SA279
1000101xx
SA404–SA407
1100101xx
SA4–SA7
0000001xx
SA140–SA143
0100011xx
SA276–SA279
1000101xx
SA408–SA411
1100110xx
SA8–SA11
0000010xx
SA144–SA147
0100100xx
SA280–SA283
1000110xx
SA412–SA415
1100111xx
SA12–SA15
0000011xx
SA148–SA151
0100101xx
SA284–SA287
1000111xx
SA416–SA419
1101000xx
SA16–SA19
0000100xx
SA152–SA155
0100110xx
SA288–SA291
1001000xx
SA420–SA423
1101001xx
SA20–SA23
0000101xx
SA156–SA159
0100111xx
SA292–SA295
1001001xx
SA424–SA427
1101010xx
SA24–SA27
0000110xx
SA160–SA163
0101000xx
SA296–SA299
1001010xx
SA428–SA431
1101011xx
SA28–SA31
0000111xx
SA164–SA167
0101001xx
SA300–SA303
1001011xx
SA432–SA435
1101100xx
SA32–SA35
0001000xx
SA168–SA171
0101010xx
SA304–SA307
1001100xx
SA436–SA439
1101101xx
SA36–SA39
0001001xx
SA172–SA175
0101011xx
SA308–SA311
1001101xx
SA440–SA443
1101110xx
SA40–SA43
0001010xx
SA176–SA179
0101100xx
SA312–SA315
1001110xx
SA444–SA447
1101111xx
SA44–SA47
0001011xx
SA180–SA183
0101101xx
SA316–SA319
1001111xx
SA448–SA451
1110000xx
SA48–SA51
0001100xx
SA184–SA187
0101110xx
SA320–SA323
1010000xx
SA452–SA455
1110001xx
SA52–SA55
0001101xx
SA188–SA191
0101111xx
SA324–SA327
1010001xx
SA456–SA459
1110010xx
SA56–SA59
0001110xx
SA192–SA195
0110000xx
SA328–SA331
1010010xx
SA460–SA463
1110011xx
SA60–SA63
0001111xx
SA196–SA199
0110001xx
SA332–SA335
1010011xx
SA464–SA467
1110100xx
SA64–SA67
0010000xx
SA200–SA203
0110010xx
SA336–SA339
1010100xx
SA468–SA471
1110101xx
SA68–SA71
0010001xx
SA204–SA207
0110011xx
SA340–SA343
1010101xx
SA472–SA475
1110110xx
SA72–SA75
0010010xx
SA208–SA211
0110100xx
SA344–SA347
1010110xx
SA476–SA479
1110111xx
SA76–SA79
0010011xx
SA212–SA215
0110101xx
SA348–SA351
1010111xx
SA480–SA483
1111000xx
SA80–SA83
0010100xx
SA216–SA219
0110110xx
SA352–SA355
1011000xx
SA484–SA487
1111001xx
SA84–SA87
0010101xx
SA220–SA223
0110111xx
SA356–SA359
1011001xx
SA488–SA491
1111010xx
SA88–SA91
0010110xx
SA224–SA227
0111000xx
SA360–SA363
1011010xx
SA492–SA495
1111011xx
SA92–SA95
0010111xx
SA228–SA231
0111001xx
SA364–SA367
1011011xx
SA496–SA499
1111100xx
SA96–SA99
0011000xx
SA232–SA235
0111010xx
SA368–SA371
1011100xx
SA500–SA503
1111101xx
SA100–SA103
0011001xx
SA236–SA239
0111011xx
SA372–SA375
1011101xx
SA504–SA507
1111110xx
SA104–SA107
0011010xx
SA240–SA243
0111100xx
SA376–SA379
1011110xx
SA508
111111100
SA108–SA111
0011011xx
SA244–SA247
0111101xx
SA380–SA383
1011111xx
SA509
111111101
SA112–SA115
0011100xx
SA248–SA251
0111110xx
SA384–SA387
1100000xx
SA510
111111110
SA116–SA119
0011101xx
SA252–SA255
0111111xx
SA388–SA391
1100001xx
SA511
111111111
SA120–SA123
0011110xx
SA256–SA259
1000000xx
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Temporary Sector Group Unprotect
This feature allows temporary unprotection of previously protected sector groups to change data
in-system. The Sector Group Unprotect mode is activated by setting the RESET# pin to VID. During this mode, formerly protected sector groups can be programmed or erased by selecting the
sector group addresses. Once VID is removed from the RESET# pin, all the previously protected
sector groups are protected again. For this feature, Figure 1 shows the algorithm, and Figure 23
shows the timing diagrams.
START
RESET# = VID
(Note 1)
Perform Erase or
Program Operations
RESET# = VIH
Temporary Sector
Group Unprotect Completed
(Note 2)
Notes:
1. All protected sector groups unprotected (If WP# = VIL, the highest or lowest address sector
remains protected for uniform sector devices, the top or bottom two address sectors remains
protected for boot sector devices).
2. All previously protected sector groups are protected once again.
Figure 1.
October 10, 2006 S29GL-M_00_B6
Temporary Sector Group Unprotect Operation
S29GL-M MirrorBitTM Flash Family
53
D a t a
S h e e t
START
START
PLSCNT = 1
RESET# = VID
Wait 1 μs
Temporary Sector
Group Unprotect
Mode
No
PLSCNT = 1
Protect all sector
groups: The indicated
portion of the sector
group protect algorithm
must be performed for all
unprotected sector
groups prior to issuing
the first sector group
unprotect address
RESET# = VID
Wait 1 μs
First Write
Cycle = 60h?
First Write
Cycle = 60h?
Temporary Sector
Group Unprotect
Mode
Yes
Yes
Set up sector
group address
No
All sector
groups
protected?
Yes
Sector Group Protect:
Write 60h to sector
group address with
A6–A0 = 0xx0010
Set up first sector
group address
Sector Group
Unprotect:
Write 60h to sector
group address with
A6–A0 = 1xx0010
Wait 150 µs
Verify Sector Group
Protect: Write 40h
to sector group
address with
A6–A0 = 0xx0010
Increment
PLSCNT
No
Reset
PLSCNT = 1
Read from
sector group address
with A6–A0
= 0xx0010
Wait 15 ms
Verify Sector Group
Unprotect: Write
40h to sector group
address with
A6–A0 = 1xx0010
Increment
PLSCNT
No
No
PLSCNT
= 25?
Read from
sector group
address with
A6–A0 = 1xx0010
Data = 01h?
Yes
No
Yes
Protect
another
sector group?
Device failed
No
Yes
No
PLSCNT
= 1000?
Yes
Remove VID
from RESET#
Device failed
Write reset
command
Sector Group
Protect
Algorithm
Sector Group
Protect complete
Set up
next sector group
address
Data = 00h?
Yes
Last sector
group
verified?
No
Yes
Sector Group
Unprotect
Algorithm
Remove VID
from RESET#
Write reset
command
Sector Group
Unprotect complete
Figure 2.
54
In-System Sector Group Protect/Sector Group Unprotect Algorithms
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Secured Silicon Sector Flash Memory Region
The Secured Silicon Sector feature provides a Flash memory region that enables permanent part
identification through an Electronic Serial Number (ESN). The Secured Silicon Sector is 256 bytes
in length, and uses a Secured Silicon Sector Indicator Bit (DQ7) to indicate whether or not the
Secured Silicon Sector is locked when shipped from the factory. This bit is permanently set at the
factory and cannot be changed, which prevents cloning of a factory locked part. This ensures the
security of the ESN once the product is shipped to the field.
The factory offers the device with the Secured Silicon Sector either customer lockable (standard
shipping option) or factory locked (contact a Spansion sales representative for ordering information). The customer-lockable version is shipped with the Secured Silicon Sector unprotected,
allowing customers to program the sector after receiving the device. The customer-lockable version also has the Secured Silicon Sector Indicator Bit permanently set to a “0.” The factory-locked
version is always protected when shipped from the factory, and has the Secured Silicon (Secured
Silicon) Sector Indicator Bit permanently set to a “1.” Thus, the Secured Silicon Sector Indicator
Bit prevents customer-lockable devices from being used to replace devices that are factory
locked.
Note: The ACC function and unlock bypass modes are not available when the Secured Silicon Sector is enabled.
The Secured Silicon sector address space in this device is allocated as follows:
Secured Silicon Sector Address Range
x16
x8
Standard
Factory
Locked
ExpressFlash
Factory
Locked
000000h – 000007h
000000h – 00000Fh
ESN
ESN or
determined by
customer
000008h – 00007Fh
000010h – 0000FFh
Unavailable
Determined by
customer
Customer
Lockable
Determined by
customer
The system accesses the Secured Silicon Sector through a command sequence (see Write Protect
(WP#)). After the system writes the Enter Secured Silicon Sector command sequence, it may read
the Secured Silicon Sector by using the addresses normally occupied by the first sector (SA0).
This mode of operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until power is removed from the device. On power-up, or following a hardware
reset, the device reverts to sending commands to sector SA0.
Customer Lockable: Secured Silicon Sector Not Programmed or Protected At the Factory
Unless otherwise specified, the device is shipped such that the customer may program and protect the 256-byte Secured Silicon sector.
The system may program the Secured Silicon Sector using the write-buffer, accelerated and/or
unlock bypass methods, in addition to the standard programming command sequence (see Command Definitions).
Programming and protecting the Secured Silicon Sector must be used with caution since, once
protected, there is no procedure available for unprotecting the Secured Silicon Sector area and
none of the bits in the Secured Silicon Sector memory space can be modified in any way.
The Secured Silicon Sector area can be protected using one of the following procedures:
„ Write the three-cycle Enter Secured Silicon Sector Region command sequence, and then follow the in-system sector protect algorithm as shown in Figure 2, except that RESET# may be
at either VIH or VID. This allows in-system protection of the Secured Silicon Sector without
raising any device pin to a high voltage. Note that this method is only applicable to the Secured Silicon Sector.
„ Write the three-cycle Enter Secured Silicon Sector Region command sequence and then use
the alternate method of sector protection described in the “Sector Group Protection and Unprotection” section.
Once the Secured Silicon Sector is programmed, locked, and verified, the system must write the
Exit Secured Silicon Sector Region command sequence to return to reading and writing within the
remainder of the array.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
55
D a t a
S h e e t
Factory Locked: Secured Silicon Sector Programmed and Protected At the Factory
In devices with an ESN, the Secured Silicon Sector is protected when the device is shipped from
the factory. The Secured Silicon Sector cannot be modified in any way. An ESN Factory Locked
device has an 16-byte random ESN at addresses 000000h–000007h. Please contact your sales
representative for details on ordering ESN Factory Locked devices.
Customers may opt to have their code programmed by the factory through the Spansion programming service (Customer Factory Locked). The devices are then shipped from the factory with
the Secured Silicon Sector permanently locked. Contact your sales representative for details on
using the Spansion programming service.
Write Protect (WP#)
The Write Protect function provides a hardware method of protecting the first or last sector group
without using VID. Write Protect is one of two functions provided by the WP#/ACC input.
If the system asserts VIL on the WP#/ACC pin, the device disables program and erase functions
in the first or last sector group independently of whether those sector groups were protected or
unprotected. Note that if WP#/ACC is at VIL when the device is in the standby mode, the maximum input load current is increased (Table 29).
Note: If the system asserts VIH on the WP#/ACC pin, the device reverts to whether the first or last sector was previously
set to be protected or unprotected using the method described in “Sector Group Protection and Unprotection”. Note that
WP# has an internal pullup; when unconnected, WP# is at VIH.
Hardware Data Protection
The command sequence requirement of unlock cycles for programming or erasing provides data
protection against inadvertent writes (Table 34 and Table 35 contain command definitions). In addition, the following hardware data protection measures prevent accidental erasure or
programming, which might otherwise be caused by spurious system level signals during VCC
power-up and power-down transitions, or from system noise.
Low VCC Write Inhibit
When VCC is less than VLKO, the device does not accept any write cycles. This protects data during
VCC power-up and power-down. The command register and all internal program/erase circuits are
disabled, and the device resets to the read mode. Subsequent writes are ignored until VCC is
greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional writes when VCC is greater than VLKO.
Write Pulse “Glitch” Protection
Noise pulses of less than 3 ns (typical) on OE#, CE# or WE# do not initiate a write cycle.
Logical Inhibit
Write cycles are inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate
a write cycle, CE# and WE# must be a logical zero while OE# is a logical one.
Power-Up Write Inhibit
If WE# = CE# = VIL and OE# = VIH during power up, the device does not accept commands on
the rising edge of WE#. The internal state machine is automatically reset to the read mode on
power-up.
56
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Common Flash Memory Interface (CFI)
The Common Flash Interface (CFI) specification outlines device and host system software interrogation handshake, which allows specific vendor-specified software algorithms to be used for
entire families of devices. Software support can then be device-independent, JEDEC ID-independent, and forward- and backward-compatible for the specified flash device families. Flash vendors
can standardize their existing interfaces for long-term compatibility.
This device enters the CFI Query mode when the system writes the CFI Query command, 98h, to
address 55h, any time the device is ready to read array data. The system can read CFI information at the addresses given in Table 30 through Table 33. To terminate reading CFI data, the
system must write the reset command.
The system can also write the CFI query command when the device is in the autoselect mode.
The device enters the CFI query mode, and the system can read CFI data at the addresses given
in Table 30 through Table 33. The system must write the reset command to return the device to
reading array data.
For further information, please refer to the CFI Specification and CFI Publication 100. Alternatively, contact your sales representative for copies of these documents.
Table 30. CFI Query Identification String
Addresses(x16)
Addresses(x8)
Data
10h
11h
12h
20h
22h
24h
0051h
0052h Query Unique ASCII string “QRY”
0059h
13h
14h
26h
28h
0002h
Primary OEM Command Set
0000h
15h
16h
2Ah
2Ch
0040h
Address for Primary Extended Table
0000h
17h
18h
2Eh
30h
0000h
Alternate OEM Command Set (00h = none exists)
0000h
19h
1Ah
32h
34h
0000h Address for Alternate OEM Extended Table
0000h (00h = none exists)
Table 31.
Addresses (x16)
Addresses (x8)
Description
System Interface String
Data
Description
1Bh
36h
VCC Min. (write/erase)
0027h
D7–D4: volt, D3–D0: 100 millivolt
1Ch
38h
0036h
1Dh
3Ah
0000h VPP Min. voltage (00h = no VPP pin present)
1Eh
3Ch
0000h VPP Max. voltage (00h = no VPP pin present)
1Fh
3Eh
0007h Reserved for future use
20h
40h
0007h
21h
42h
000Ah Typical timeout per individual block erase 2N ms
22h
44h
0000h
23h
46h
0001h Reserved for future use
24h
48h
0005h Max. timeout for buffer write 2N times typical
25h
4Ah
0004h Max. timeout per individual block erase 2N times typical
26h
4Ch
0000h
VCC Max. (write/erase)
D7–D4: volt, D3–D0: 100 millivolt
Typical timeout for Min. size buffer write 2N µs
(00h = not supported)
Typical timeout for full chip erase 2N ms
(00h = not supported)
Max. timeout for full chip erase 2N times typical
(00h = not supported)
Note: CFI data related to VCC and time-outs may differ from actual VCC and time-outs of the product. Please consult the
Ordering Information tables to obtain the VCC range for particular part numbers. See the Erase and Programming
Performance table for typical timeout specifications.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
57
D a t a
Table 32.
58
S h e e t
Device Geometry Definition
Addresses
(x16)
Addresses
(x8)
Data
27h
4Eh
0019h
0018h
0017h
0016h
Device Size = 2N byte
19 = 256 Mb, 18 = 128 Mb, 17 = 64 Mb, 16 = 32 Mb
28h
29h
50h
52h
000xh
0000h
Flash Device Interface description (refer to CFI publication 100)
0000h = x8-only bus devices
0001h = x16-only bus devices
0002h = x8/x16 bus devices
2Ah
2Bh
54h
56h
0005h
0000h
Max. number of byte in multi-byte write = 2N
(00h = not supported)
2Ch
58h
0001h
0002h
Number of Erase Block Regions within device
(01h = uniform device, 02h = boot device)
2Dh
2Eh
2Fh
30h
5Ah
5Ch
5Eh
60h
00xxh
000xh
00x0h
000xh
Erase Block Region 1 Information
(refer to the CFI specification or CFI publication 100)
003Fh, 0000h, 0000h, 0001h = 32 Mb (-R0, -R1, -R2, R5, R6)
007Fh, 0000h, 0020h, 0000h = 32 Mb (-R3, -R4), 64 Mb (-R3, -R4)
007Fh, 0000h, 0000h, 0001h = 64 Mb (-R0, -R1, -R2, -R5, -R6, -R7)
00FFh, 0000h, 0000h, 0001h = 128 Mb
00FFh, 0001h, 0000h, 0001h = 256 Mb
31h
32h
33h
34h
60h
64h
66h
68h
00xxh
0000h
0000h
000xh
Erase Block Region 2 Information (refer to CFI publication 100)
003Eh, 0000h, 0000h, 0001h = 32 Mb (-R1, -R2)
007Eh, 0000h, 0000h, 0001h = 64 Mb (-R1, -R2)
0000h, 0000h, 0000h, 0000h = all others
35h
36h
37h
38h
6Ah
6Ch
6Eh
70h
0000h
0000h
0000h
0000h
Erase Block Region 3 Information (refer to CFI publication 100)
39h
3Ah
3Bh
3Ch
72h
74h
76h
78h
0000h
0000h
0000h
0000h
Erase Block Region 4 Information (refer to CFI publication 100)
Description
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Table 33.
Primary Vendor-Specific Extended Query
Addresses
(x16)
Addresses
(x8)
Data
40h
41h
42h
80h
82h
84h
0050h
0052h
0049h
Query-unique ASCII string “PRI”
43h
86h
0031h
Major version number, ASCII
44h
88h
0033h
Minor version number, ASCII
45h
8Ah
000xh
Address Sensitive Unlock (Bits 1-0)
0 = Required, 1 = Not Required
Process Technology (Bits 7-2) 0010b = 0.23 μm MirrorBit
0009h = x8-only bus devices 0008h = all other devices
46h
8Ch
0002h
Erase Suspend
0 = Not Supported, 1 = To Read Only, 2 = To Read & Write
47h
8Eh
0001h
Sector Protect
0 = Not Supported, X = Number of sectors in per group
48h
90h
0001h
Sector Temporary Unprotect
00 = Not Supported, 01 = Supported
49h
92h
0004h
Sector Protect/Unprotect scheme
0004h = Standard Mode (Refer to Text)
4Ah
94h
0000h
Simultaneous Operation
00 = Not Supported, X = Number of Sectors in Bank
4Bh
96h
0000h
Burst Mode Type
00 = Not Supported, 01 = Supported
4Ch
98h
0001h
Page Mode Type
00 = Not Supported, 01 = 4 Word Page, 02 = 8 Word Page
4Dh
9Ah
00B5h
ACC (Acceleration) Supply Minimum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
4Eh
9Ch
00C5h
ACC (Acceleration) Supply Maximum
00h = Not Supported, D7-D4: Volt, D3-D0: 100 mV
October 10, 2006 S29GL-M_00_B6
Description
4Fh
9Eh
00xxh
Top/Bottom Boot Sector Flag
00h = Uniform Device without WP# protect,
02h = Bottom Boot Device, 03h = Top Boot Device,
04h = Uniform sectors bottom WP# protect,
05h = Uniform sectors top WP# protect
50h
A0h
0001h
Program Suspend< 00h = Not Supported, 01h = Supported
S29GL-M MirrorBitTM Flash Family
59
D a t a
S h e e t
Command Definitions
Writing specific address and data commands or sequences into the command register initiates
device operations. Table 34 and Table 35 define the valid register command sequences. Writing
incorrect address and data values or writing them in the improper sequence may place the device
in an unknown state. A reset command is then required to return the device to reading array data.
All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is
latched on the rising edge of WE# or CE#, whichever happens first. See AC Characteristics for
timing diagrams.
Reading Array Data
The device is automatically set to reading array data after device power-up. No commands are
required to retrieve data. The device is ready to read array data after completing an Embedded
Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the erase-suspend-read
mode, after which the system can read data from any non-erase-suspended sector. After completing a programming operation in the Erase Suspend mode, the system may once again read
array data with the same exception. See Erase Suspend/Erase Resume Commands for more
information.
The system must issue the reset command to return the device to the read (or erase-suspendread) mode if DQ5 goes high during an active program or erase operation, or if the device is in
the autoselect mode. See the next section, Reset Command, for more information.
See also Requirements for Reading Array Data in the Device Bus Operations section for more information. The Read-Only Operations–AC Characteristics provides the read parameters, and
Figure 13 shows the timing diagram.
Reset Command
Writing the reset command resets the device to the read or erase-suspend-read mode. Address
bits are don’t cares for this command.
The reset command may be written between the sequence cycles in an erase command sequence
before erasing begins. This resets the device to the read mode. Once erasure begins, however,
the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the device to the read mode. If the program
command sequence is written while the device is in the Erase Suspend mode, writing the reset
command returns the device to the erase-suspend-read mode. Once programming begins, however, the device ignores reset commands until the operation is complete.
The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode, the reset command must be written to return to the read
mode. If the device entered the autoselect mode while in the Erase Suspend mode, writing the
reset command returns the device to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the
device to the read mode (or erase-suspend-read mode if the device was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write
the Write-to-Buffer-Abort Reset command sequence to reset the device for the next operation.
60
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Autoselect Command Sequence
The autoselect command sequence allows the host system to read several identifier codes at specific addresses:
Identifier Code
A7:A0
(x16)
A6:A-1
(x8)
00h
Manufacturer ID
00h
Device ID, Cycle 1
01h
02h
Device ID, Cycle 2
0Eh
1Ch
1Eh
Device ID, Cycle 3
0Fh
Secured Silicon Sector Factory Protect
03h
06h
Sector Protect Verify
(SA)02h
(SA)04h
Note: 3.The device ID is read over three cycles. SA = Sector Address
The autoselect command sequence is initiated by first writing two unlock cycles. This is followed
by a third write cycle that contains the autoselect command. The device then enters the autoselect mode. The system may read at any address any number of times without initiating another
autoselect command sequence:
The system must write the reset command to return to the read mode (or erase-suspend-read
mode if the device was previously in Erase Suspend).
Enter/Exit Secured Silicon Sector Command Sequence
The Secured Silicon Sector region provides a secured data area containing an 8-word/16-byte
random Electronic Serial Number (ESN). The system can access the Secured Silicon Sector region
by issuing the three-cycle Enter Secured Silicon Sector command sequence. The device continues
to access the Secured Silicon Sector region until the system issues the four-cycle Exit Secured
Silicon Sector command sequence. The Exit Secured Silicon Sector command sequence returns
the device to normal operation. Table 34 and Table 35 show the address and data requirements
for both command sequences. Also, see Secured Silicon Sector Flash Memory Region for further
information. Note that the ACC function and unlock bypass modes are not available when the Secured Silicon Sector is enabled.
Word Program Command Sequence
Programming is a four-bus-cycle operation. The program command sequence is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and
data are written next, which in turn initiate the Embedded Program algorithm. The system is not
required to provide further controls or timings. The device automatically provides internally generated program pulses and verifies the programmed cell margin. Table 34 and Table 35 show the
address and data requirements for the word program command sequence, respectively.
When the Embedded Program algorithm is complete, the device then returns to the read mode
and addresses are no longer latched. The system can determine the status of the program operation by using DQ7 or DQ6. See Write Operation Status for information on these status bits. Any
commands written to the device during the Embedded Program Algorithm are ignored. Note that
the Secured Silicon Sector, autoselect, and CFI functions are unavailable when a program operation is in progress. Note that a hardware reset immediately terminates the program operation.
The program command sequence should be reinitiated once the device returns to the read mode,
to ensure data integrity.
Programming is allowed in any sequence of address locations and across sector boundaries. Programming to the same word address multiple times without intervening erases (incremental bit
programming) requires a modified programming method. For such application requirements,
please contact your local Spansion representative. Word programming is supported for backward
compatibility with existing Flash driver software and for occasional writing of individual words. Use
of write buffer programming (see below) is strongly recommended for general programming use
when more than a few words are to be programmed. The effective word programming time using
write buffer programming is approximately four times shorter than the single word programming
time.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
61
D a t a
S h e e t
Any bit in a word cannot be programmed from “0” back to a “1.” Attempting to do so may
cause the device to set DQ5=1, or cause DQ7 and DQ6 status bits to indicate the operation was
successful. However, a succeeding read shows that the data is still “0.” Only erase operations can
convert a “0” to a “1.”
Unlock Bypass Command Sequence
The unlock bypass feature allows the system to program words to the device faster than using
the standard program command sequence. The unlock bypass command sequence is initiated by
first writing two unlock cycles. This is followed by a third write cycle containing the unlock bypass
command, 20h. The device then enters the unlock bypass mode. A two-cycle unlock bypass mode
command sequence is all that is required to program in this mode. The first cycle in this sequence
contains the unlock bypass program command, A0h; the second cycle contains the program address and data. Additional data is programmed in the same manner. This mode dispenses with
the initial two unlock cycles required in the standard program command sequence, resulting in
faster total programming time. Table 34 and Table 35 show the requirements for the command
sequence.
During the unlock bypass mode, only the Unlock Bypass Program and Unlock Bypass Reset commands are valid. To exit the unlock bypass mode, the system must issue the two-cycle unlock
bypass reset command sequence. The first cycle must contain the data 90h. The second cycle
must contain the data 00h. The device then returns to the read mode.
Write Buffer Programming
Write Buffer Programming allows the system write to a maximum of 16 words/32 bytes in one
programming operation. This results in faster effective programming time than the standard programming algorithms. The Write Buffer Programming command sequence is initiated by first
writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load
command written at the Sector Address in which programming occurs. The fourth cycle writes the
sector address and the number of word locations, minus one, to be programmed. For example, if
the system programs six unique address locations, then 05h should be written to the device. This
tells the device how many write buffer addresses are loaded with data and therefore when to expect the Program Buffer to Flash command. The number of locations to program cannot exceed
the size of the write buffer or the operation aborts.
The fifth cycle writes the first address location and data to be programmed. The write-buffer-page
is selected by address bits AMAX–A4. All subsequent address/data pairs must fall within the selected-write-buffer-page. The system then writes the remaining address/data pairs into the write
buffer. Write buffer locations may be loaded in any order.
The write-buffer-page address must be the same for all address/data pairs loaded into the write
buffer. (This means Write Buffer Programming cannot be performed across multiple write-buffer
pages.) This also means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts to load programming data outside of the selected write-buffer page,
the operation aborts.
Note that if a Write Buffer address location is loaded multiple times, the address/data pair counter
is decremented for every data load operation. The host system must therefore account for loading
a write-buffer location more than once. The counter decrements for each data load operation, not
for each unique write-buffer-address location. Note also that if an address location is loaded more
than once into the buffer, the final data loaded for that address is programmed.
Once the specified number of write buffer locations are loaded, the system must then write the
Program Buffer to Flash command at the sector address. Any other address and data combination
aborts the Write Buffer Programming operation. The device then begins programming. Data polling should be used while monitoring the last address location loaded into the write buffer. DQ7,
DQ6, DQ5, and DQ1 should be monitored to determine the device status during Write Buffer
Programming.
The write-buffer programming operation can be suspended using the standard program suspend/
resume commands. Upon successful completion of the Write Buffer Programming operation, the
device is ready to execute the next command.
The Write Buffer Programming Sequence can be aborted in the following ways:
„ Load a value that is greater than the page buffer size during the Number of Locations to Program step.
62
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
„ Write to an address in a sector different than the one specified during the Write-Buffer-Load
command.
„ Write an Address/Data pair to a different write-buffer-page than the one selected by the
Starting Address during the write buffer data loading stage of the operation.
„ Write data other than the Confirm Command after the specified number of data load cycles.
The abort condition is indicated by DQ1 = 1, DQ7 = DATA# (for the last address location loaded),
DQ6 = toggle, and DQ5=0. A Write-to-Buffer-Abort Reset command sequence must be written to
reset the device for the next operation.
Note that the Secured Silicon Sector, autoselect, and CFI functions are unavailable when a program operation is in progress. This flash device is capable of handling multiple write buffer
programming operations on the same write buffer address range without intervening erases. For
applications requiring incremental bit programming, a modified programming method is required;
please contact your local Spansion representative. Any bit in a write buffer address range
cannot be programmed from “0” back to a “1.” Attempting to do so can cause the device to
set DQ5=1, of cause the DQ7 and DQ6 status bits to indicate the operation was successful. However, a succeeding read shows that the data is still “0.” Only erase operations can convert a “0”
to a “1.”
Accelerated Program
The device offers accelerated program operations through the WP#/ACC or ACC pin depending
on the particular product. When the system asserts VHH on the WP#/ACC or ACC pin. The device
uses the higher voltage on the WP#/ACC or ACC pin to accelerate the operation. Note that the
WP#/ACC pin must not be at VHH for operations other than accelerated programming, or device
damage can result. WP# has an internal pullup; when unconnected, WP# is at VIH.
Figure 3 illustrates the algorithm for the program operation. See Erase and Program Operations—
S29GL032M Only and AC Characteristics for parameters, and Figure 14 for timing diagrams.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
63
D a t a
S h e e t
Write “Write to Buffer”
command and
Sector Address
Part of “Write to Buffer”
Command Sequence
Write number of addresses
to program minus 1(WC)
and Sector Address
Write first address/data
Yes
WC = 0 ?
No
Abort Write to
Buffer Operation?
Write to a different
sector address
Yes
Write to buffer ABORTED.
Must write “Write-to-buffer
Abort Reset” command
sequence to return
to read mode.
No
Write next address/data pair
(Note 1)
WC = WC - 1
Write program buffer to
flash sector address
Read DQ7 - DQ0 at
Last Loaded Address
DQ7 = Data?
No
Notes:
1. When Sector Address is specified, any address in
the selected sector is acceptable. However, when
loading Write-Buffer address locations with data, all
addresses must fall within the selected Write-Buffer
Page.
2. DQ7 may change simultaneously with DQ5.
Therefore, DQ7 should be verified.
3. If this flowchart location was reached because
DQ5= “1”, then the device FAILED. If this flowchart
location was reached because DQ1= “1”, then the
Write to Buffer operation was ABORTED. In either
case, the proper reset command must be written
before the device can begin another operation. If
DQ1=1, write the Write-Buffer-ProgrammingAbort-Reset command. if DQ5=1, write the Reset
command.
4. See Table 34 and Table 35 for command sequences
required for write buffer programming.
Yes
No
No
DQ1 = 1?
DQ5 = 1?
Yes
Yes
Read DQ7 - DQ0 with
address = Last Loaded
Address
(Note 2)
DQ7 = Data?
Yes
No
(Note 3)
FAIL or ABORT
PASS
Figure 3. Write Buffer Programming Operation
64
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
START
Write Program
Command Sequence
Data Poll
from System
Embedded
Program
algorithm
in progress
Verify Data?
No
Yes
Increment Address
No
Last Address?
Yes
Programming
Completed
Note: See Table 34 and Table 35 for program command sequence
Figure 4. Program Operation
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming operation or a
Write to Buffer programming operation so that data can be read from any non-suspended sector.
When the Program Suspend command is written during a programming process, the device halts
the program operation within 15 µs maximum (5 µs typical) and updates the status bits. Addresses are not required when writing the Program Suspend command.
After the programming operation is suspended, the system can read array data from any nonsuspended sector. The Program Suspend command can also be issued during a programming operation while an erase is suspended. In this case, data can be read from any addresses not in
Erase Suspend or Program Suspend. If a read is needed from the Secured Silicon Sector area
(One-time Program area), then user must use the proper command sequences to enter and exit
this region. Note that the Secured Silicon Sector, autoselect, and CFI functions are unavailable
when a program operation is in progress.
The system can also write the autoselect command sequence when the device is in the Program
Suspend mode. The system can read as many autoselect codes as required. When the device
exits the autoselect mode, the device reverts to the Program Suspend mode, and is ready for another valid operation. See Autoselect Command Sequence for more information.
After the Program Resume command is written, the device reverts to programming. The system
can determine the status of the program operation using the DQ7 or DQ6 status bits, just as in
the standard program operation. See Write Operation Status for more information.
The system must write the Program Resume command (address bits are don’t care) to exit the
Program Suspend mode and continue the programming operation. Further writes of the Resume
command are ignored. Another Program Suspend command can be written after the device resumes programming.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
65
D a t a
S h e e t
Program Operation
or Write-to-Buffer
Sequence in Progress
Write address/data
XXXh/B0h
Write Program Suspend
Command Sequence
Command is also valid for
Erase-suspended-program
operations
Wait 15 μs
Read data as
required
No
Autoselect and SecSi Sector
read operations are also allowed
Data cannot be read from erase- or
program-suspended sectors
Done
reading?
Yes
Write address/data
XXXh/30h
Write Program Resume
Command Sequence
Device reverts to
operation prior to
Program Suspend
Figure 5.
Program Suspend/Program Resume
Chip Erase Command Sequence
Chip erase is a six bus cycle operation. The chip erase command sequence is initiated by writing
two unlock cycles, followed by a set-up command. Two additional unlock write cycles are then
followed by the chip erase command, which in turn invokes the Embedded Erase algorithm. The
device does not require the system to preprogram prior to erase. The Embedded Erase algorithm
automatically preprograms and verifies the entire memory for an all zero data pattern prior to
electrical erase. The system is not required to provide any controls or timings during these operations. Table 34 and Table 35 show the address and data requirements for the chip erase
command sequence.
When the Embedded Erase algorithm is complete, the device returns to the read mode and addresses are no longer latched. The system can determine the status of the erase operation by
using DQ7, DQ6, or DQ2. See Write Operation Status for information on these status bits.
Any commands written during the chip erase operation are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs, the chip erase command
sequence should be reinitiated once the device returns to reading array data, to ensure data
integrity.
Figure 6 illustrates the algorithm for the erase operation. See Erase and Programming Performance in AC Characteristics for parameters, and Figure 18 for timing diagrams.
Sector Erase Command Sequence
Sector erase is a six bus cycle operation. The sector erase command sequence is initiated by writing two unlock cycles, followed by a set-up command. Two additional unlock cycles are written,
and are then followed by the address of the sector to be erased, and the sector erase command.
Table 34 and Table 35 shows the address and data requirements for the sector erase command
sequence.
66
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
The device does not require the system to preprogram prior to erase. The Embedded Erase algorithm automatically programs and verifies the entire memory for an all zero data pattern prior to
electrical erase. The system is not required to provide any controls or timings during these
operations.
After the command sequence is written, a sector erase time-out of 50 µs occurs. During the timeout period, additional sector addresses and sector erase commands can be written. Loading the
sector erase buffer can be done in any sequence, and the number of sectors can be from one
sector to all sectors. The time between these additional cycles must be less than 50 µs, otherwise
erasure may begin. Any sector erase address and command following the exceeded time-out can
or cannot be accepted. It is recommended that processor interrupts be disabled during this time
to ensure all commands are accepted. The interrupts can be re-enabled after the last Sector Erase
command is written. Any command other than Sector Erase or Erase Suspend during the
time-out period resets the device to the read mode. Note that the Secured Silicon Sector,
autoselect, and CFI functions are unavailable when an erase operation is in progress. The system
must rewrite the command sequence and any additional addresses and commands.
The system can monitor DQ3 to determine if the sector erase timer has timed out (See the section
on DQ3: Sector Erase Timer.). The time-out begins from the rising edge of the final WE# pulse in
the command sequence.
When the Embedded Erase algorithm is complete, the device returns to reading array data and
addresses are no longer latched. The system can determine the status of the erase operation by
reading DQ7, DQ6, or DQ2 in the erasing sector. See Write Operation Status for information on
these status bits.
Once the sector erase operation starts, only the Erase Suspend command is valid. All other commands are ignored. However, note that a hardware reset immediately terminates the erase
operation. If that occurs, the sector erase command sequence should be reinitiated once the device returns to reading array data, to ensure data integrity.
Figure 6 illustrates the algorithm for the erase operation. See Erase and Programming Performance in AC Characteristics for parameters, and Figure 18 for timing diagrams.
l
START
Write Erase
Command Sequence
(Notes 1, 2)
Data Poll to Erasing
Bank from System
No
Embedded
Erase
algorithm
in progress
Data = FFh?
Yes
Erasure Completed
Notes:
1. See Table 34 and Table 35 for program command sequence.
2. See DQ3: Sector Erase Timer for information on the sector erase timer.
Figure 6.
October 10, 2006 S29GL-M_00_B6
Erase Operation
S29GL-M MirrorBitTM Flash Family
67
D a t a
S h e e t
Erase Suspend/Erase Resume Commands
The Erase Suspend command, B0h, allows the system to interrupt a sector erase operation and
then read data from, or program data to, any sector not selected for erasure. This command is
valid only during the sector erase operation, including the 50 µs time-out period during the sector
erase command sequence. The Erase Suspend command is ignored if written during the chip
erase operation or Embedded Program algorithm.
When the Erase Suspend command is written during the sector erase operation, the device requires a typical of 5 µs (maximum of 20 µs) to suspend the erase operation. However, when the
Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation.
After the erase operation is suspended, the device enters the erase-suspend-read mode. The system can read data from or program data to any sector not selected for erasure. (The device “erase
suspends” all sectors selected for erasure.) Reading at any address within erase-suspended sectors produces status information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2
together, to determine if a sector is actively erasing or is erase-suspended. See Write Operation
Status for information on these status bits.
After an erase-suspended program operation is complete, the device returns to the erase-suspend-read mode. The system can determine the status of the program operation using the DQ7
or DQ6 status bits, just as in the standard word program operation. See Write Operation Status
for more information.
In the erase-suspend-read mode, the system can also issue the autoselect command sequence.
See Autoselect Mode and Autoselect Command Sequence for details.
To resume the sector erase operation, the system must write the Erase Resume command. Further writes of the Resume command are ignored. Another Erase Suspend command can be
written after the chip resumes erasing.
Note: During an erase operation, this flash device performs multiple internal operations which are invisible to the system.
When an erase operation is suspended, any of the internal operations that were not fully completed must be restarted. As
such, if this flash device is continually issued suspend/resume commands in rapid succession, erase progress are impeded
as a function of the number of suspends. The result is a longer cumulative erase time than without suspends. Note that the
additional suspends do not affect device reliability or future performance. In most systems rapid erase/suspend activity
occurs only briefly. In such cases, erase performance is not significantly impacted.
68
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Command Definitions
Command
Sequence
(Note 1)
Cycles
Table 34.
Command Definitions( x16 Mode, BYTE# = VIH)
Bus Cycles (Notes 2–5)
First
Second
Addr
Data
RD
Third
Fourth
Fifth
Addr
Data
Addr
Data
Addr
Data
Sixth
Addr
Data
Addr
Data
X0E
(Note
18)
X0F
(Note
18)
1
RA
Reset (7)
1
XXX
F0
Manufacturer ID
4
555
AA
2AA
55
555
90
X00
0001
Device ID (9)
4
555
AA
2AA
55
555
90
X01
227E
Secured Silicon Sector Factory
Protect (10)
4
555
AA
2AA
55
555
90
X03
(Note 10)
Sector Group Protect Verify
(12)
4
555
AA
2AA
55
555
90
(SA)X02
00/01
Enter Secured Silicon Sector Region
3
555
AA
2AA
55
555
88
Exit Secured Silicon Sector Region
4
555
AA
2AA
55
555
90
XXX
00
Program
4
555
AA
2AA
55
555
A0
PA
PD
Write to Buffer (11)
3
555
AA
2AA
55
SA
25
SA
WC
PA
PD
WBL
PD
Program Buffer to Flash
1
SA
29
Write to Buffer Abort Reset (13)
3
555
AA
2AA
55
555
F0
Unlock Bypass
3
555
AA
2AA
55
555
20
Unlock Bypass Program (14)
2
XXX
A0
PA
PD
Unlock Bypass Reset (15)
2
XXX
90
XXX
00
Chip Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
555
10
Sector Erase
6
555
AA
2AA
55
555
80
555
AA
2AA
55
SA
30
Program/Erase Suspend (16)
1
XXX
B0
Program/Erase Resume (16)
1
XXX
30
CFI Query (18)
1
55
98
Autoselect (Note 8)
Read (6)
Legend:
X = Don’t care
RA = Read Address of memory location to be read.
RD = Read Data read from location RA during read operation.
PA = Program Address. Addresses latch on falling edge of WE# or
CE# pulse, whichever happens later.
Notes:
1. See Table 1 for description of bus operations.
2. All values are in hexadecimal.
3. Shaded cells indicate read cycles. All others are write cycles.
4. During unlock and command cycles, when lower address bits are
555 or 2AA as shown in table, address bits above A11 and data
bits above DQ7 are don’t care.
5. No unlock or command cycles required when device is in read
mode.
6. Reset command is required to return to read mode (or to erasesuspend-read mode if previously in Erase Suspend) when device
is in autoselect mode, or if DQ5 goes high while device is
providing status information.
7. Fourth cycle of the autoselect command sequence is a read
cycle. Data bits DQ15–DQ8 are don’t care. Except for RD, PD
and WC. See Autoselect Command Sequence for more
information.
8. Device ID must be read in three cycles.
9. If WP# protects highest address sector, data is 98h for factory
locked and 18h for not factory locked. If WP# protects lowest
address sector, data is 88h for factory locked and 08h for not
factor locked.
October 10, 2006 S29GL-M_00_B6
PD = Program Data for location PA. Data latches on rising edge of
WE# or CE# pulse, whichever happens first.
SA = Sector Address of sector to be verified (in autoselect mode) or
erased. Address bits A21–A15 uniquely select any sector.
WBL = Write Buffer Location. Address must be within same write
buffer page as PA.
WC = Word Count. Number of write buffer locations to load minus 1.
10. Data is 00h for an unprotected sector group and 01h for a
protected sector group.
11. Total number of cycles in command sequence is determined by
number of words written to write buffer. Maximum number of
cycles in command sequence is 21, including “Program Buffer to
Flash” command.
12. Command sequence resets device for next command after
aborted write-to-buffer operation.
13. Unlock Bypass command is required prior to Unlock Bypass
Program command.
14. Unlock Bypass Reset command is required to return to read
mode when device is in unlock bypass mode.
15. System may read and program in non-erasing sectors, or enter
autoselect mode, when in Erase Suspend mode. Erase Suspend
command is valid only during a sector erase operation.
16. Erase Resume command is valid only during Erase Suspend
mode.
17. Command is valid when device is ready to read array data or
when device is in autoselect mode.
18. Refer to Table 17, AutoSelect Codes for individual Device IDs
per device density and model number.
S29GL-M MirrorBitTM Flash Family
69
D a t a
S h e e t
Command
Sequence
(Note 1)
Cycles
Table 35. Command Definitions (x8 Mode, BYTE# = VIL)
Bus Cycles (Notes 2–5)
First
Addr Data Addr Data
Read (6)
1
RA
RD
Reset (7)
1
XXX
F0
Autoselect
(Note 8)
Second
Third
Fourth
Fifth
Addr
Data
Addr
Data
Manufacturer ID
4
AAA
AA
555
55
AAA
90
X00
01
Device ID (9)
4
AAA
AA
555
55
AAA
90
X02
7E
Secured Silicon Sector Factory
Protect (10)
4
AAA
AA
555
55
AAA
90
X06
(Note 10)
Sector Group Protect Verify (12)
(SA)X04
00/01
Sixth
Addr
Data
Addr
Data
X1C
(Note 17)
X1E
(Note 17)
PA
PD
WBL
PD
4
AAA
AA
555
55
AAA
90
Enter Secured Silicon Sector Region
3
AAA
AA
555
55
AAA
88
Exit Secured Silicon Sector Region
4
AAA
AA
555
55
AAA
90
XXX
00
Write to Buffer (11)
3
AAA
AA
555
55
SA
25
SA
BC
Program Buffer to Flash
1
SA
29
Write to Buffer Abort Reset (13)
3
AAA
AA
555
55
AAA
F0
Chip Erase
6
AAA
AA
555
55
AAA
80
AAA
AA
555
55
AAA
10
Sector Erase
6
AAA
AA
555
55
AAA
80
AAA
AA
555
55
SA
30
Program/Erase Suspend (14)
1
XXX
B0
Program/Erase Resume (15)
1
XXX
30
CFI Query (16)
1
AA
98
Legend:
X = Don’t care
RA = Read Address of memory location to be read.
RD = Read Data read from location RA during read operation.
PA = Program Address. Addresses latch on falling edge of WE# or
CE# pulse, whichever happens later.
PD = Program Data for location PA. Data latches on rising edge of
WE# or CE# pulse, whichever happens first.
SA = Sector Address of sector to be verified (in autoselect mode) or
erased. Address bits A21–A15 uniquely select any sector.
WBL = Write Buffer Location. Address must be within same write
buffer page as PA.
BC = Byte Count. Number of write buffer locations to load minus 1.
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
9.
70
See Table 1 for description of bus operations.
All values are in hexadecimal.
Shaded cells indicate read cycles. All others are write cycles.
During unlock and command cycles, when lower address bits are
555 or AAA as shown in table, address bits above A11 are don’t
care.
Unless otherwise noted, address bits A21–A11 are don’t cares.
No unlock or command cycles required when device is in read
mode.
Reset command is required to return to read mode (or to erasesuspend-read mode if previously in Erase Suspend) when device
is in autoselect mode, or if DQ5 goes high while device is
providing status information.
Fourth cycle of autoselect command sequence is a read cycle.
Data bits DQ15–DQ8 are don’t care. See Autoselect Command
Sequence section or more information.
Device ID must be read in three cycles.
10. If WP# protects highest address sector, data is 98h for factory
locked and 18h for not factory locked. If WP# protects lowest
address sector, data is 88h for factory locked and 08h for not
factor locked.
11. Data is 00h for an unprotected sector group and 01h for a
protected sector group.
12. Total number of cycles in command sequence is determined by
number of bytes written to write buffer. Maximum number of
cycles in command sequence is 37, including “Program Buffer to
Flash” command.
13. Command sequence resets device for next command after
aborted write-to-buffer operation.
14. System may read and program in non-erasing sectors, or enter
autoselect mode, when in Erase Suspend mode. Erase Suspend
command is valid only during a sector erase operation.
15. Erase Resume command is valid only during Erase Suspend
mode.
16. Command is valid when device is ready to read array data or
when device is in autoselect mode.
17. Refer to Table 17, AutoSelect Codes for individual Device IDs
per device density and model number.
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Write Operation Status
The device provides several bits to determine the status of a program or erase operation: DQ2,
DQ3, DQ5, DQ6, and DQ7. Table 36 and the following subsections describe the function of these
bits. DQ7 and DQ6 each offer a method for determining whether a program or erase operation is
complete or in progress. The device also provides a hardware-based output signal, RY/BY#, to
determine whether an Embedded Program or Erase operation is in progress or is completed.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system whether an Embedded Program or Erase
algorithm is in progress or completed, or whether the device is in Erase Suspend. Data# Polling
is valid after the rising edge of the final WE# pulse in the command sequence.
During the Embedded Program algorithm, the device outputs on DQ7 the complement of the
datum programmed to DQ7. This DQ7 status also applies to programming during Erase Suspend.
When the Embedded Program algorithm is complete, the device outputs the datum programmed
to DQ7. The system must provide the program address to read valid status information on DQ7.
If a program address falls within a protected sector, Data# Polling on DQ7 is active for approximately 1 µs, then the device returns to the read mode.
During the Embedded Erase algorithm, Data# Polling produces a “0” on DQ7. When the Embedded Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling
produces a “1” on DQ7. The system must provide an address within any of the sectors selected
for erasure to read valid status information on DQ7.
After an erase command sequence is written, if all sectors selected for erasing are protected,
Data# Polling on DQ7 is active for approximately 100 µs, then the device returns to the read
mode. If not all selected sectors are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. However, if the system reads
DQ7 at an address within a protected sector, the status may not be valid.
Just prior to the completion of an Embedded Program or Erase operation, DQ7 can change asynchronously with DQ0–DQ6 while Output Enable (OE#) is asserted low. That is, the device can
change from providing status information to valid data on DQ7. Depending on when the system
samples the DQ7 output, it can read the status or valid data. Even if the device has completed
the program or erase operation and DQ7 has valid data, the data outputs on DQ0–DQ6 may be
still invalid. Valid data on DQ0–DQ7 appears on successive read cycles.
Table 36 shows the outputs for Data# Polling on DQ7. Figure 7 shows the Data# Polling algorithm. Figure 17 shows the Data# Polling timing diagram.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
71
D a t a
S h e e t
START
Read DQ15–DQ0
Addr = VA
DQ7 = Data?
Yes
No
No
DQ5 = 1?
Yes
Read DQ15–DQ0
Addr = VA
DQ7 = Data?
Yes
No
FAIL
PASS
Notes:
1. VA = Valid address for programming. During a sector erase operation, a valid address is any
sector address within the sector being erased. During chip erase, a valid address is any
non-protected sector address.
2. DQ7 should be rechecked even if DQ5 = “1” because DQ7 can change simultaneously with DQ5.
Figure 7.
Data# Polling Algorithm
RY/BY#: Ready/Busy#
The RY/BY# is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE#
pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can
be tied together in parallel with a pull-up resistor to VCC.
If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is in the read mode,
the standby mode, or in the erase-suspend-read mode. Table 36 shows the outputs for RY/BY#.
DQ6: Toggle Bit I
Toggle Bit I on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or
complete, or whether the device entered the Erase Suspend mode. Toggle Bit I may be read at
any address, and is valid after the rising edge of the final WE# pulse in the command sequence
(prior to the program or erase operation), and during the sector erase time-out.
During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system may use either OE# or CE# to control the read cycles.
When the operation is complete, DQ6 stops toggling.
72
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
After an erase command sequence is written, if all sectors selected for erasing are protected, DQ6
toggles for approximately 100 µs, then returns to reading array data. If not all selected sectors
are protected, the Embedded Erase algorithm erases the unprotected sectors, and ignores the
selected sectors that are protected.
The system can use DQ6 and DQ2 together to determine whether a sector is actively erasing or
is erase-suspended. When the device is actively erasing (that is, the Embedded Erase algorithm
is in progress), DQ6 toggles. When the device enters the Erase Suspend mode, DQ6 stops toggling. However, the system must also use DQ2 to determine which sectors are erasing or erasesuspended. Alternatively, the system can use DQ7 (see the subsection on DQ7: Data# Polling).
If a program address falls within a protected sector, DQ6 toggles for approximately 1 µs after the
program command sequence is written, then returns to reading array data.
DQ6 also toggles during the erase-suspend-program mode, and stops toggling once the Embedded Program algorithm is complete.
Table 36 shows the outputs for Toggle Bit I on DQ6. Figure 8 shows the toggle bit algorithm.
Figure 20 shows the toggle bit timing diagrams. Figure 21 shows the differences between DQ2
and DQ6 in graphical form. Also, see DQ2: Toggle Bit II.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
73
D a t a
S h e e t
START
Read DQ7–DQ0
Read DQ7–DQ0
Toggle Bit
= Toggle?
No
Yes
No
DQ5 = 1?
Yes
Read DQ7–DQ0
Twice
Toggle Bit
= Toggle?
No
Yes
Program/Erase
Operation Not
Complete, Write
Reset Command
Program/Erase
Operation Complete
Note: The system should recheck the toggle bit even if DQ5 = “1” because the toggle bit may stop toggling as DQ5
changes to “1.” See the subsections on DQ6 and DQ2 for more information.
Figure 8.
Toggle Bit Algorithm
DQ2: Toggle Bit II
The “Toggle Bit II” on DQ2, when used with DQ6, indicates whether a particular sector is actively
erasing (that is, the Embedded Erase algorithm is in progress), or whether that sector is erasesuspended. Toggle Bit II is valid after the rising edge of the final WE# pulse in the command
sequence.
DQ2 toggles when the system reads at addresses within those sectors that are selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But DQ2 cannot
distinguish whether the sector is actively erasing or is erase-suspended. DQ6, by comparison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish
which sectors are selected for erasure. Thus, both status bits are required for sector and mode
information. Refer to Table 36 to compare outputs for DQ2 and DQ6.
74
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Figure 8 shows the toggle bit algorithm in flowchart form, and the section “DQ2: Toggle Bit II”
explains the algorithm, also see RY/BY#: Ready/Busy#. Figure 20 shows the toggle bit timing diagram. Figure 21 shows the differences between DQ2 and DQ6 in graphical form.
Whenever the system initially begins reading toggle bit status, it must read DQ7–DQ0 at least
twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and
store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has
completed the program or erase operation. The system can read array data on DQ7–DQ0 on the
following read cycle.
However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of DQ5 is high (see the section on DQ5). If
it is, the system should then determine again whether the toggle bit is toggling, since the toggle
bit may have stopped toggling just as DQ5 went high. If the toggle bit is no longer toggling, the
device has successfully completed the program or erase operation. If it is still toggling, the device
did not completed the operation successfully, and the system must write the reset command to
return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit is toggling and
DQ5 did not go high. The system may continue to monitor the toggle bit and DQ5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively,
it may choose to perform other system tasks. In this case, the system must start at the beginning
of the algorithm when it returns to determine the status of the operation (top of Figure 6).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program, erase, or write-to-buffer time exceeded a specified internal
pulse count limit. Under these conditions DQ5 produces a “1,” indicating that the program or erase
cycle was not successfully completed.
The device may output a “1” on DQ5 if the system tries to program a “1” to a location that was
previously programmed to “0.” Only an erase operation can change a “0” back to a “1.”
Under this condition, the device halts the operation, and when the timing limit is exceeded, DQ5
produces a “1.”
In all these cases, the system must write the reset command to return the device to the reading
the array (or to erase-suspend-read if the device was previously in the erase-suspend-program
mode).
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to determine whether
or not erasure started. (The sector erase timer does not apply to the chip erase command.) If
additional sectors are selected for erasure, the entire time-out also applies after each additional
sector erase command. When the time-out period is complete, DQ3 switches from a “0” to a “1.”
If the time between additional sector erase commands from the system can be assumed to be
less than 50 µs, the system need not monitor DQ3(see Sector Erase Command Sequence).
After the sector erase command is written, the system should read the status of DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device accepted the command sequence, and then
reads DQ3. If DQ3 is “1,” the Embedded Erase algorithm started; all further commands (except
Erase Suspend) are ignored until the erase operation is complete. If DQ3 is “0,” the device accepts
additional sector erase commands. To ensure the command was accepted, the system software
should check the status of DQ3 prior to and following each subsequent sector erase command. If
DQ3 is high on the second status check, the last command might not have been accepted.
Table 36 shows the status of DQ3 relative to the other status bits.
DQ1: Write-to-Buffer Abort
DQ1 indicates whether a Write-to-Buffer operation was aborted. Under these conditions DQ1 produces a “1”. The system must issue the Write-to-Buffer-Abort-Reset command sequence to return
the device to reading array data. See Write Buffer for more details.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
75
D a t a
S h e e t
Table 36. Write Operation Status
Status
Standar Embedded Program Algorithm
d
Mode Embedded Erase Algorithm
Program ProgramSuspend Suspend
Mode Read
DQ6
DQ5
(Note 1)
DQ3
DQ2
(Note 2)
DQ1
RY/BY#
DQ7#
Toggle
0
N/A
No toggle
0
0
0
Toggle
0
1
Toggle
N/A
0
Program-Suspended Sector
Invalid (not allowed)
1
Data
1
Non-Program
Suspended Sector
Erase-Suspended Sector
EraseSuspend
Non-Erase Suspended
Erase
Suspend Read
Sector
Mode
Erase-Suspend-Program
(Embedded Program)
WritetoBuffer
DQ7
(Note 2
)
1
No toggle
0
N/A
Toggle
N/A
Data
1
1
DQ7#
Toggle
0
N/A
N/A
N/A
0
Busy (Note 3)
DQ7#
Toggle
0
N/A
N/A
0
0
Abort (Note 4)
DQ7#
Toggle
0
N/A
N/A
1
0
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program, Embedded Erase, or Write-to-Buffer operation
exceeded the maximum timing limits. Refer to the section on DQ5 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate
subsection for further details.
3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address
location.
4. DQ1 switches to ‘1’ when the device aborts the write-to-buffer operation
76
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Absolute Maximum Ratings
Storage Temperature, Plastic Packages . . . . . . . . . . . . . . . . –65°C to +150°C
Ambient Temperature with Power Applied . . . . . . . . . . . . . . –65°C to +125°C
Voltage with Respect to Ground:
VCC (Note 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–0.5 V to +4.0 V
. . . . . . . . . . . . A9, OE#, ACC and RESET# (Note 2)–0.5 V to +12.5 V
All other pins (Note 1) . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC+0.5 V
Output Short Circuit Current (Note 3). . . . . . . . . . . . . . . . . . . . . . . . 200 mA
Notes:
1.
2.
3.
4.
Minimum DC voltage on input or I/Os is –0.5 V. During voltage transitions, inputs or I/Os may
overshoot VSS to –2.0 V for periods of up to 20 ns. See Figure 9, Maximum Negative
Overshoot Waveform. Maximum DC voltage on input or I/Os is VCC + 0.5 V. During voltage
transitions, input or I/O pins may overshoot to VCC + 2.0 V for periods up to 20 ns. See Figure 10.
Minimum DC input voltage on pins A9, OE#, ACC, and RESET# is –0.5 V. During voltage
transitions, A9, OE#, ACC, and RESET# may overshoot VSS to –2.0 V for periods of up to 20 ns.
See Figure 9. Maximum DC input voltage on pin A9, OE#, ACC, and RESET# is +12.5 V which may
overshoot to +14.0V for periods up to 20 ns.
No more than one output may be shorted to ground at a time. Duration of the short circuit should
not be greater than one second.
Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to
the device. This is a stress rating only; functional operation of the device at these or any other
conditions above those indicated in the operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating conditions for extended periods may affect
device reliability.
20 ns
20 ns
+0.8 V
–0.5 V
–2.0 V
20 ns
Figure 9.
Maximum Negative Overshoot Waveform
20 ns
VCC
+2.0 V
VCC
+0.5 V
2.0 V
20 ns
Figure 10.
20 ns
Maximum Positive Overshoot Waveform
Industrial (I) Devices
Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to +85°C
Supply Voltages
VCC for full voltage range . . . . . . . . . . . . . . . . . . . . . . . . . +2.7 V to +3.6 V
VCC for regulated voltage range . . . . . . . . . . . . . . . . . . . . . +3.0 V to +3.6 V
VIO
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCC
Note: Operating ranges define those limits between which the functionality of the
device is guaranteed.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
77
D a t a
S h e e t
DC Characteristics
CMOS Compatible
Parameter
Symbol
Parameter Description
(Notes)
Test Conditions
Min
Typ
Max
Uni
t
±1.0
µA
ILI
Input Load Current (1)
VIN = VSS to VCC,
VCC = VCC max
ILIT
A9, ACC Input Load Current
VCC = VCC max; A9 = 12.5 V
35
µA
ILR
Reset Leakage Current
VCC = VCC max; RESET# = 12.5 V
35
µA
Output Leakage Current
VOUT = VSS to VCC,
VCC = VCC max
±1.0
µA
ILO
1 MHz
ICC1
VCC Initial Read Current (2, 3)
CE# = VIL, OE# = VIH
5
20
5 MHz (4)
18
25
5 MHz (5)
25
35
10 MHz (4)
35
50
10 MHz (5)
40
60
10 MHz
5
20
40 MHz
10
40
mA
mA
ICC2
VCC Intra-Page Read Current (2, 3)
CE# = VIL, OE# = VIH
ICC3
VCC Active Write Current (3, 4)
CE# = VIL, OE# = VIH
50
60
mA
ICC4
VCC Standby Current (3)
CE#, RESET# = VCC ± 0.3 V,
WP# = VIH
1
5
µA
ICC5
VCC Reset Current (3)
RESET# = VSS ± 0.3 V, WP# = VIH
1
5
µA
ICC6
Automatic Sleep Mode (3, 7)
VIH = VCC ± 0.3 V;
-0.1< VIL ≤ 0.3 V, WP# = VIH
1
5
µA
VIL
Input Low Voltage (1, 8)
0.8
V
–0.5
VIH
Input High Voltage 1, 8)
VCC + 0.5
V
VHH
Voltage for ACC Program Acceleration
VCC = 2.7 –3.6 V
11.5
12.0
12.5
V
VID
Voltage for Autoselect and
Temporary Sector Unprotect
VCC = 2.7 –3.6 V
11.5
12.0
12.5
V
VOL
Output Low Voltage (8)
IOL = 4.0 mA, VCC = VCC min
0.45
V
VOH1
VOH2
VLKO
Output High Voltage
0.7 VCC
IOH = –2.0 mA, VCC = VCC min
0.85 VCC
IOH = –100 µA, VCC = VCC min
VCC–0.4
Low VCC Lock-Out Voltage (9)
2.3
V
V
2.5
V
Notes:
1. On the WP#/ACC pin only, the maximum input load current when WP# = VIL is ±5.0 µA.
2. The ICC current listed is typically less than 3.5 mA/MHz, with OE# at VIH.
3. Maximum ICC specifications are tested with VCC = VCCmax.
4. S29GL032M, S29GL064M
5. S29GL128M, S29GL256M
6. ICC active while Embedded Erase or Embedded Program is in progress.
7. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30
ns.
8. VCC voltage requirements.
9. Not 100% tested.
78
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Test Conditions
3.3 V
2.7 kΩ
Device
Under
Test
CL
6.2 kΩ
Note: Diodes are IN3064 or equivalent
Figure 11.
Table 37.
Test Setup
Test Specifications
Test Condition
All Speeds
Output Load
Unit
1 TTL gate
Output Load Capacitance, CL
(including jig capacitance)
Input Rise and Fall Times
Input Pulse Levels
30
pF
5
ns
0.0 or VCC
V
Input timing measurement reference levels
(See Note)
0.5 VCC
V
Output timing measurement reference levels
0.5 VCC
V
Key to Switching Waveforms
WAVEFORM
INPUTS
OUTPUTS
Steady
Changing from H to L
Changing from L to H
VCC
Input
0.5 VCC
Don’t Care,
Any Change Permitted
Changing, State Unknown
Does Not Apply
Center Line is High
Impedance State (High Z)
Measurement Level
0.5 VCC
Output
0.0 V
Figure 12. Input Waveforms and Measurement Levels
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
79
D a t a
S h e e t
AC Characteristics
Read-Only Operations—S29GL256M Only
Parameter
Description
JEDEC
Std.
tAVAV
tRC
tAVQV
tACC Address to Output Delay
tELQV
tCE
Speed Options
Test Setup
11
Min
100
100
ns
CE#, OE# = VIL
Max
100
100
ns
OE# = VIL
Max
100
100
ns
Max
30
30
ns
30
Read Cycle Time (Note 1)
Chip Enable to Output Delay
Unit
10
tPACC Page Access Time
tGLQV
tOE
Output Enable to Output Delay
Max
tEHQZ
tDF
Chip Enable to Output High Z (Note 1)
Max
16
ns
tGHQZ
tDF
Output Enable to Output High Z (Note 1)
Max
16
ns
tAXQX
tOH
Output Hold Time From Addresses, CE# or OE#,
Whichever Occurs First
Min
0
ns
Read
Min
0
ns
Toggle and
Data# Polling
Min
10
ns
tOEH Output Enable Hold Time (Note 1)
30
ns
Notes:
1. Not 100% tested.
2. See Figure 11 and Table 37 for test specifications.
Read-Only Operations—S29GL128M only
Parameter
JEDEC
Description
Std.
tAVAV
tRC
tAVQV
tACC Address to Output Delay
tELQV
tCE
Speed Options
Test Setup
Read Cycle Time (Note 1)
Chip Enable to Output Delay
tPACC Page Access Time
90
10
Unit
Min
90
100
ns
CE#, OE# = VIL
Max
90
100
ns
OE# = VIL
Max
90
100
ns
Max
25
30
ns
25
30
ns
tGLQV
tOE
Output Enable to Output Delay
Max
tEHQZ
tDF
Chip Enable to Output High Z (Note 1)
Max
16
ns
tGHQZ
tDF
Output Enable to Output High Z (Note 1)
Max
16
ns
tAXQX
tOH
Output Hold Time From Addresses, CE# or OE#,
Whichever Occurs First
Min
0
ns
Read
Min
0
ns
Toggle and
Data# Polling
Min
10
ns
tOEH Output Enable Hold Time (Note 1)
Notes:
1. Not 100% tested.
2. See Figure 11 and Table 37 for test specifications.
80
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Read-Only Operations—S29GL064M Only
Parameter
Description
JEDEC
Std.
tAVAV
tRC
tAVQV
tACC Address to Output Delay
tELQV
tCE
Speed Options
Test Setup
10
11
Min
90
100
110
ns
CE#, OE# = VIL
Max
90
100
110
ns
OE# = VIL
Max
90
100
110
ns
ns
Read Cycle Time (Note 1)
Chip Enable to Output Delay
tPACC Page Access Time
Unit
90
Max
25
30
30
tGLQV
tOE
Output Enable to Output Delay
Max
25
30
30
tEHQZ
tDF
Chip Enable to Output High Z (See Note)
Max
16
ns
tGHQZ
tDF
Output Enable to Output High Z (See Note)
Max
16
ns
tOH
Output Hold Time From Addresses, CE# or OE#,
Whichever Occurs First
Min
0
ns
Read
Min
0
ns
Toggle and
Data# Polling
Min
10
ns
tAXQX
tOEH Output Enable Hold Time (See Note)
ns
Note: Not 100% tested.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
81
D a t a
S h e e t
AC Characteristics
Read-Only Operations—S29GL032M only
Parameter
Description
JEDEC
Std.
tAVAV
tRC
tAVQV
tACC Address to Output Delay
tELQV
tCE
Speed Options
Test Setup
Unit
90
10
11
Min
90
100
110
ns
CE#, OE# = VIL
Max
90
100
110
ns
OE# = VIL
Max
90
100
110
ns
Max
25
30
30
ns
25
30
30
Read Cycle Time (Note 1)
Chip Enable to Output Delay
tPACC Page Access Time
tGLQV
tOE
Output Enable to Output Delay
Max
tEHQZ
tDF
Chip Enable to Output High Z (Note 1)
Max
16
ns
tGHQZ
tDF
Output Enable to Output High Z (Note 1)
Max
16
ns
tAXQX
tOH
Output Hold Time From Addresses, CE# or OE#,
Whichever Occurs First
Min
0
ns
Read
Min
0
ns
Toggle and
Data# Polling
Min
10
ns
tOEH Output Enable Hold Time (Note 1)
ns
Notes:
1. Not 100% tested.
2. See Figure 11 and Table 37 for test specifications.
tRC
Addresses Stable
Addresses
tACC
CE#
tRH
tRH
tDF
tOE
OE#
tOEH
WE#
tCE
tOH
HIGH Z
HIGH Z
Output Valid
Outputs
RESET#
RY/BY#
0V
Figure 13.
82
Read Operation Timings
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
AC Characteristics
Same Page
A23-A2
A1-A0*
Aa
tACC
Data Bus
Ab
Qa
Ad
Ac
tPACC
tPACC
Qb
tPACC
Qc
Qd
CE#
OE#
Note: Figure shows device in word mode. Addresses are A1–A-1 for byte mode.
Figure 14. Page Read Timings
Hardware Reset (RESET#)
Parameter
JEDEC
Description
Std.
All Speed
Options
Unit
tReady
RESET# Pin Low (During Embedded Algorithms) to Read Mode
(See Note)
Max
20
µs
tReady
RESET# Pin Low (NOT During Embedded Algorithms) to Read
Mode (See Note)
Max
500
ns
tRP
RESET# Pulse Width
Min
500
ns
tRH
Reset High Time Before Read (See Note)
Min
50
ns
tRPD
RESET# Input Low to Standby Mode (See Note)
Min
20
µs
tRB
RY/BY# Output High to CE#, OE# pin Low
Min
0
ns
Note: Not 100% tested.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
83
D a t a
S h e e t
AC Characteristics
RY/BY#
CE#, OE#
tRH
RESET#
tRP
tReady
Reset Timings NOT during Embedded Algorithms
Reset Timings during Embedded Algorithms
tReady
RY/BY#
tRB
CE#, OE#
tRH
RESET#
tRP
Figure 15.
84
Reset Timings
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
AC Characteristics
Erase and Program Operations—S29GL256M Only
Parameter
Speed Options
Description
Std.
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tASO
Address Setup Time to OE# low during toggle bit polling
Min
15
ns
tAH
Address Hold Time
Min
45
ns
tAHT
Address Hold Time From CE# or OE# high during toggle bit polling Min
0
ns
tDVWH
tDS
Data Setup Time
Min
45
ns
tWHDX
tDH
Data Hold Time
Min
0
ns
tWLAX
tGHWL
10
11
Unit
JEDEC
100
110
ns
tCEPH
CE# High during toggle bit polling
Min
20
ns
tOEPH
OE# High during toggle bit polling
Min
20
ns
tGHWL
Read Recovery Time Before Write (OE# High to WE# Low)
Min
0
ns
ns
tELWL
tCS
CE# Setup Time
Min
0
tWHEH
tCH
CE# Hold Time
Min
0
ns
tWLWH
tWP
Write Pulse Width
Min
35
ns
tWHDL
tWPH
Write Pulse Width High
Min
30
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
240
Single Word Program Operation (Note 2)
Typ
60
Accelerated Single Word Program Operation (Note 2)
Typ
54
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
tVHH
VHH Rise and Fall Time (Note 1)
Min
250
ns
tVCS
VCC Setup Time (Note 1)
Min
50
µs
tBUSY
WE# High to RY/BY# Low
Min
tPOLL
Program Valid before Status Polling
Ma
x
tWHWH1
tWHWH2
tWHWH1
100
µs
sec
110
4
ns
µs
Notes:
1. Not 100% tested.
2. See Erase and Programming Performance for more information.
3. For 1–16 words/1–32 bytes programmed.
4. If a program suspend command is issued within tPOLL, the device requires tPOLL before reading
status data, once programming resumes (that is, the program resume command is written). If the
suspend command was issued after tPOLL, status data is available immediately after programming
resumes. See Figure 16.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
85
D a t a
S h e e t
AC Characteristics
Erase and Program Operations—S29GL128M Only
Parameter
Speed Options
Description
Std.
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tASO
Address Setup Time to OE# low during toggle bit polling
Min
15
ns
tAH
Address Hold Time
Min
45
ns
tAHT
Address Hold Time From CE# or OE# high during toggle bit polling
Min
0
ns
tDVWH
tDS
Data Setup Time
Min
45
ns
tWHDX
tDH
Data Hold Time
Min
0
ns
tWLAX
tGHWL
90
10
Uni
t
JEDEC
90
100
ns
tCEPH
CE# High during toggle bit polling
Min
20
ns
tOEPH
OE# High during toggle bit polling
Min
20
ns
tGHWL
Read Recovery Time Before Write (OE# High to WE# Low)
Min
0
ns
ns
tELWL
tCS
CE# Setup Time
Min
0
tWHEH
tCH
CE# Hold Time
Min
0
ns
tWLWH
tWP
Write Pulse Width
Min
35
ns
tWHDL
tWPH
Write Pulse Width High
Min
30
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
240
Single Word Program Operation (Note 2)
Typ
60
Accelerated Single Word Program Operation (Note 2)
Typ
54
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
tVHH
VHH Rise and Fall Time (Note 1)
Min
250
ns
tVCS
VCC Setup Time (Note 1)
Min
50
µs
tBUSY
WE# High to RY/BY# Low
Min
tPOLL
Program Valid before Status Polling
Max
tWHWH1
tWHWH2
tWHWH1
90
µs
sec
100
4
ns
µs
Notes:
1. Not 100% tested.
2. See Erase and Programming Performance for more information
3. For 1–16 words/1–32 bytes programmed.
4. If a program suspend command is issued within tPOLL, the device requires tPOLL before reading
status data, once programming resumes (that is, the program resume command has been
written). If the suspend command was issued after tPOLL, status data is available immediately
after programming resumes. See Figure 16.
86
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
AC Characteristics
Erase and Program Operations—S29GL064M Only
Parameter
Speed Options
Description
Std.
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tASO
Address Setup Time to OE# low during toggle bit polling
Min
15
ns
tAH
Address Hold Time
Min
45
ns
tAHT
Address Hold Time From CE# or OE# high during toggle bit polling
Min
0
ns
tDVWH
tDS
Data Setup Time
Min
35
ns
tWHDX
tDH
Data Hold Time
Min
0
ns
ns
tWLAX
tGHWL
90
10
11
90
100
110
Unit
JEDEC
ns
tCEPH
CE# High during toggle bit polling
Min
20
tOEPH
OE# High during toggle bit polling
Min
20
ns
tGHWL
Read Recovery Time Before Write (OE# High to WE# Low)
Min
0
ns
tELWL
tCS
CE# Setup Time
Min
0
ns
tWHEH
tCH
CE# Hold Time
Min
0
ns
tWLWH
tWP
Write Pulse Width
Min
35
ns
tWHDL
tWPH
Write Pulse Width High
Min
30
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
240
Typ
60
Typ
54
tWHWH2 Sector Erase Operation (Note 2)
Typ
0.5
tVHH
VHH Rise and Fall Time (Note 1)
Min
250
ns
tVCS
VCC Setup Time (Note 1)
Min
50
µs
tBUSY
WE# High to RY/BY# Low
Min
tPOLL
Program Valid before Status Polling
Max
tWHWH1
tWHWH1 Single Word Program Operation (Note 2)
Accelerated Single Word Program Operation (Note 2)
tWHWH2
90
100
4
µs
sec
110
ns
µs
Notes:
1. Not 100% tested.
2. See Erase and Programming Performance for more information
3. For 1–16 words/1–32 bytes programmed.
4. If a program suspend command is issued within tPOLL, the device requires tPOLL before reading
status data, once programming resumes (that is, the program resume command has been
written). If the suspend command was issued after tPOLL, status data is available immediately
after programming resumes. See Figure 16.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
87
D a t a
S h e e t
AC Characteristics
Erase and Program Operations—S29GL032M Only
Parameter
Speed Options
Description
Std.
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tASO
Address Setup Time to OE# low during toggle bit polling
Min
15
ns
tAH
Address Hold Time
Min
45
ns
tAHT
Address Hold Time From CE# or OE# high during toggle bit polling Min
0
ns
tDVWH
tDS
Data Setup Time
Min
35
ns
tWHDX
tDH
Data Hold Time
Min
0
ns
tWLAX
tGHWL
90
10
11
90
100
110
Unit
JEDEC
ns
tCEPH
CE# High during toggle bit polling
Min
20
ns
tOEPH
OE# High during toggle bit polling
Min
20
ns
tGHWL
Read Recovery Time Before Write (OE# High to WE# Low)
Min
0
ns
ns
tELWL
tCS
CE# Setup Time
Min
0
tWHEH
tCH
CE# Hold Time
Min
0
ns
tWLWH
tWP
Write Pulse Width
Min
35
ns
tWHDL
tWPH
Write Pulse Width High
Min
30
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
240
Single Word Program Operation (Note 2)
Typ
60
Accelerated Single Word Program Operation (Note 2)
Typ
54
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
tVHH
VHH Rise and Fall Time (Note 1)
Min
250
ns
tVCS
VCC Setup Time (Note 1)
Min
50
µs
tBUSY
WE# High to RY/BY# Low
Min
tPOLL
Program Valid before Status Polling
Max
tWHWH1
tWHWH2
tWHWH1
90
100
4
µs
sec
110
ns
µs
Notes:
1. Not 100% tested.
2. See Erase and Programming Performance for more information
3. For 1–16 words/1–32 bytes programmed.
4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation.
5. If a program suspend command is issued within tPOLL, the device requires tPOLL before reading
status data, once programming resumes (that is, the program resume command has been
written). If the suspend command was issued after tPOLL, status data is available immediately
after programming resumes. See Figure 16.
88
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
AC Characteristics
Program Command Sequence (last two cycles)
tAS
tWC
Addresses
Read Status Data (last two cycles)
555h
PA
PA
PA
tAH
CE#
tCH
OE#
tPOLL
tWP
WE#
tWPH
tCS
tDS
tWHWH1
tDH
A0h
Data
PD
Status
tBUSY
DOUT
tRB
RY/BY#
VCC
tVCS
Notes:
1. PA = program address, PD = program data, DOUT is the true data at the program address.
2. Illustration shows device in word mode.
Figure 16. Program Operation Timings
VHH
HH
ACC
VIL
IL or VIH
IH
VIL
IL or VIH
IH
tVHH
VHH
Figure 17.
October 10, 2006 S29GL-M_00_B6
tVHH
VHH
Accelerated Program Timing Diagram
S29GL-M MirrorBitTM Flash Family
89
D a t a
S h e e t
AC Characteristics
Erase Command Sequence (last two cycles)
tAS
tWC
2AAh
Addresses
Read Status Data
VA
SA
VA
555h for chip erase
tAH
CE#
tCH
OE#
tWP
WE#
tWPH
tCS
tWHWH2
tDS
tDH
Data
55h
In
Progress
30h
Complete
10 for Chip Erase
tBUSY
tRB
RY/BY#
tVCS
VCC
Notes:
1. SA = sector address (for Sector Erase), VA = Valid Address for reading status data (see Write
Operation Status).
2. Illustration shows device in word mode.
Figure 18.
Chip/Sector Erase Operation Timings
tRC
Addresses
VA
tPOLL
VA
VA
tACC
tCE
CE#
tCH
tOE
OE#
tOEH
tDF
WE#
tOH
High Z
DQ7
Complement
Complement
DQ0–DQ6
Status Data
Status Data
True
Valid Data
High Z
True
Valid Data
tBUSY
RY/BY#
Note: VA = Valid address. Illustration shows first status cycle after command sequence, last status read cycle, and array
data read cycle.
Figure 19. Data# Polling Timings
(During Embedded Algorithms)
90
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
AC Characteristics
tAHT
tAS
Addresses
tAHT
tASO
CE#
tCEPH
tOEH
WE#
tOEPH
OE#
tDH
DQ6 / DQ2
tOE
Valid
Status
Valid
Status
Valid
Status
(first read)
(second read)
(stops toggling)
Valid Data
Valid Data
RY/BY#
Note: VA = Valid address; not required for DQ6. Illustration shows first two status cycle after command sequence, last
status read cycle, and array data read cycle.
Figure 20.
Enter
Embedded
Erasing
Erase
Suspend
Erase
WE#
Toggle Bit Timings (During Embedded Algorithms)
Enter Erase
Suspend Program
Erase
Suspend
Program
Erase Suspend
Read
Erase
Resume
Erase
Complete
Erase
Erase Suspend
Read
DQ6
DQ2
Note: DQ2 toggles only when read at an address within an erase-suspended sector. The system may use OE# or CE# to
toggle DQ2 and DQ6.
Figure 21.
DQ2 vs. DQ6
Temporary Sector Unprotect
Parameter
JEDEC
Description
Std
tVIDR
tRSP
VID Rise and Fall Time (See Note)
RESET# Setup Time for Temporary Sector Unprotect
All Speed Options
Unit
Min
500
ns
Min
4
µs
Note: Not 100% tested.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
91
D a t a
S h e e t
AC Characteristics
VID
RESET#
VID
VSS, VIL,
or VIH
VSS, VIL,
or VIH
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRRB
tRSP
RY/BY#
Figure 22. Temporary Sector Group Unprotect Timing Diagram
VID
VIH
RESET#
SA, A6,
A3, A2,
A1, A0
Valid*
Valid*
Sector Group Protect or Unprotect
Data
60h
60h
Valid*
Verify
40h
Status
Sector Group Protect: 150 µs,
Sector Group Unprotect: 15 ms
1 µs
CE#
WE#
OE#
Note: For sector group protect, A6:A0 = 0xx0010. For sector group unprotect, A6:A0 = 1xx0010.
Figure 23.
92
Sector Group Protect and Unprotect Timing Diagram
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Alternate CE# Controlled Erase and Program Operations—S29GL256M
Parameter
Speed Options
Description
Std.
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tELAX
tAH
Address Hold Time
Min
45
ns
tDVEH
tDS
Data Setup Time
Min
45
ns
tEHDX
tDH
Data Hold Time
Min
0
ns
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
ns
tGHEL
tGHEL
10
11
100
110
Unit
JEDEC
ns
tWLEL
tWS
WE# Setup Time
Min
0
tEHWH
tWH
WE# Hold Time
Min
0
ns
tELEH
tCP
CE# Pulse Width
Min
35
ns
tEHEL
tCPH
CE# Pulse Width High
Min
25
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
240
Single Word Program Operation (Note 2)
Typ
60
Accelerated Single Word Program Operation (Note 2)
Typ
54
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
tRH
RESET# High Time Before Write
Min
50
ns
Program Valid before Status Polling
Max
4
µs
tWHWH1
tWHWH2
tWHWH1
tPOLL
µs
sec
Notes:
1. Not 100% tested.
2. See Erase and Programming Performance for more information
3. For 1–16 words/1–32 bytes programmed.
4. If a program suspend command is issued within tPOLL, the device requires tPOLL before reading
status data, once programming resume (that is, the program resume command has been written).
If the suspend command was issued after tPOLL, status data is available immediately after
programming resumes. See Figure 24.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
93
D a t a
S h e e t
Alternate CE# Controlled Erase and Program Operations—S29GL128M
Parameter
Speed Options
Description
10
11
100
110
Unit
JEDEC
Std.
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tELAX
tAH
Address Hold Time
Min
45
ns
tDVEH
tDS
Data Setup Time
Min
45
ns
tEHDX
tDH
Data Hold Time
Min
0
ns
tGHEL
tGHEL
Read Recovery Time Before Write (OE# High to WE# Low)
Min
0
ns
ns
ns
tWLEL
tWS
WE# Setup Time
Min
0
tEHWH
tWH
WE# Hold Time
Min
0
ns
tELEH
tCP
CE# Pulse Width
Min
35
ns
tEHEL
tCPH
CE# Pulse Width High
Min
25
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
240
Single Word Program Operation (Note 2)
Typ
60
Accelerated Single Word Program Operation (Note 2)
Typ
54
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
sec
tRH
RESET# High Time Before Write
Min
50
ns
Program Valid before Status Polling (Note 4)
Max
4
µs
tWHWH1
tWHWH2
tWHWH1
tPOLL
µs
Notes:
1. Not 100% tested.
2. See See Erase and Programming Performance for more information
3. For 1–16 words/1–32 bytes programmed.
4. If a program suspend command is issued within tPOLL, the device requires tPOLL before reading
status data, once programming resumes (that is, the program resume command has been
written). If the suspend command was issued after tPOLL, status data is available immediately
after programming resumes. See Figure 24.
94
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Alternate CE# Controlled Erase and Program Operations—S29GL064M
Parameter
Speed Options
Description
90
10
11
90
100
110
Unit
JEDEC
Std.
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tELAX
tAH
Address Hold Time
Min
45
ns
tDVEH
tDS
Data Setup Time
Min
35
ns
tEHDX
tDH
Data Hold Time
Min
0
ns
tGHEL
tGHEL
Read Recovery Time Before Write (OE# High to WE# Low)
Min
0
ns
ns
tWLEL
tWS
WE# Setup Time
Min
0
ns
tEHWH
tWH
WE# Hold Time
Min
0
ns
tELEH
tCP
CE# Pulse Width
Min
35
ns
tEHEL
tCPH
CE# Pulse Width High
Min
25
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
240
Single Word Program Operation (Note 2)
Typ
60
Accelerated Single Word Program Operation (Note 2)
Typ
54
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
sec
tRH
RESET# High Time Before Write
Min
50
ns
Program Valid before Status Polling (Note 5)
Ma
x
4
µs
tWHWH1
tWHWH2
tWHWH1
tPOLL
µs
Notes:
1. Not 100% tested.
2. See Erase and Programming Performance for more information
3. For 1–16 words/1–32 bytes programmed.
4. If a program suspend command is issued within tPOLL, the device requires tPOLL before reading
status data, once programming resumes (that is, the program resume command has been
written). If the suspend command was issued after tPOLL, status data is available immediately
after programming resumes. See Figure 24.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
95
D a t a
S h e e t
Alternate CE# Controlled Erase and Program Operations—S29GL032M
Parameter
Speed Options
Description
Std.
tAVAV
tWC
Write Cycle Time (Note 1)
Min
tAVWL
tAS
Address Setup Time
Min
0
ns
tELAX
tAH
Address Hold Time
Min
45
ns
tDVEH
tDS
Data Setup Time
Min
35
ns
tEHDX
tDH
Data Hold Time
Min
0
ns
Read Recovery Time Before Write
(OE# High to WE# Low)
Min
0
ns
ns
tGHEL
tGHEL
90
10
11
90
100
110
Unit
JEDEC
ns
tWLEL
tWS
WE# Setup Time
Min
0
tEHWH
tWH
WE# Hold Time
Min
0
ns
tELEH
tCP
CE# Pulse Width
Min
35
ns
tEHEL
tCPH
CE# Pulse Width High
Min
25
ns
Write Buffer Program Operation (Notes 2, 3)
Typ
240
Single Word Program Operation (Note 2)
Typ
60
Accelerated Single Word Program Operation (Note 2)
Typ
54
tWHWH2
Sector Erase Operation (Note 2)
Typ
0.5
sec
tRH
RESET# High Time Before Write
Min
50
ns
Program Valid before Status Polling (Note 4)
Max
4
µs
tWHWH1
tWHWH2
tWHWH1
tPOLL
µs
Notes:
1. Not 100% tested.
2. See Erase and Programming Performance for more information
3. For 1–16 words/1–32 bytes programmed.
4. If a program suspend command is issued within tPOLL, the device requires tPOLL before reading
status data, once programming resumes (that is, the program resume command has been
written). If the suspend command was issued after tPOLL, status data is available immediately
after programming resumes. See Figure 24.
96
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
PBA for program
2AA for erase
S h e e t
SA for program buffer to flash
SA for sector erase
555 for chip erase
Data# Polling
Addresses
PA
tWC
tAS
tAH
tWH
WE#
tGHEL
tPOLL
OE#
tCP
CE#
tWS
tWHWH1 or 2
tCPH
tBUSY
tDS
tDH
DQ7#
Data
tRH
PBD for program
55 for erase
DOUT
29 for program buffer to flash
30 for sector erase
10 for chip erase
RESET#
RY/BY#
Notes:
1. Figure indicates last two bus cycles of a program or erase operation.
2. PA = program address, SA = sector address, PD = program data.
3. DQ7# is the complement of the data written to the device. DOUT is the data written to the device.
4. Illustration shows device in word mode.
Figure 24.
October 10, 2006 S29GL-M_00_B6
Alternate CE# Controlled Write (Erase/Program) Operation Timings
S29GL-M MirrorBitTM Flash Family
97
D a t a
S h e e t
Erase and Programming Performance
Parameter
(Notes)
Typ
(Note 1)
Max
(Note 2)
Unit
0.5
3.5
sec
32
64
S29GL064M
64
128
S29GL128M
128
256
S29GL256M
256
512
Sector Erase Time
S29GL032M
Chip Erase Time
sec
Total Write Buffer Program Time (3, 5)
240
µs
Total Accelerated Effective Write Buffer Program Time
(4, 5)
200
µs
S29GL032M
Chip Program Time
Comments
Excludes 00h
programming
prior to
erasure
(Note 6)
Excludes
system level
overhead
(Note 7)
31.5
S29GL064M
63
S29GL128M
126
S29GL256M
252
sec
Notes:
1. Typical program and erase times assume the following conditions: 25°C, VCC = 3.0V, 10,000
cycles; checkerboard data pattern.
2. Under worst case conditions of 90°C; Worst case VCC, 100,000 cycles.
3. Effective programming time (typ) is 15 μs (per word), 7.5 μs (per byte).
4. Effective accelerated programming time (typ) is 12.5 μs (per word), 6.3 μs (per byte).
5. Effective write buffer specification is calculated on a per-word/per-byte basis for a 16-word/32byte write buffer operation.
6. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h
before erasure.
7. System-level overhead is the time required to execute the command sequence(s) for the program
command. See Table 34 and Table 35 for further information on command definitions.
TSOP Pin and BGA Package Capacitance
For package types TA, TF, BA, BF, FA, FF (refer to Ordering Information Pages):
Parameter
Symbol
Parameter
Description
CIN
Input Capacitance
VIN = 0
COUT
Output Capacitance
VOUT = 0
CIN2
Control Pin Capacitance
Test
Setup
VIN = 0
Typ
Max
Unit
TSOP
6
7.5
pF
BGA
4.2
5.0
pF
TSOP
8.5
12
pF
BGA
5.4
6.5
pF
TSOP
7.5
9
pF
BGA
3.9
4.7
pF
For package types TB, TC, BB, BC, (refer to Ordering Information Pages):
Parameter
Symbol
Parameter
Description
CIN
Input Capacitance
VIN = 0
COUT
Output Capacitance
VOUT = 0
CIN2
Control Pin Capacitance
VIN = 0
CIN3
RESET# and WP#/ACC Pin Capacitance
Test
Setup
VIN = 0
Typ
Max
Unit
TSOP
8
10
pF
BGA
8
10
pF
TSOP
8.5
12
pF
BGA
8.5
12
pF
TSOP
8
10
pF
BGA
8
10
pF
TSOP
20
25
pF
BGA
15
20
pF
Notes:
1. Sampled, not 100% tested.
2. Test conditions TA = 25°C, f = 1.0 MHz.
98
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Physical Dimensions
TS040—40-Pin Standard Thin Small Outline Package (TSOP)
Dwg rev AA; 10/99
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
99
D a t a
S h e e t
Physical Dimensions
TSR040—40-Pin Standard and Reverse Thin Small Outline Package (TSOP)
REVERSE PIN OUT (TOP VIEW)
A2
3
0.10 C
1
N
SEE DETAIL B
-A-
-BE 5
e
N
+1
2
N
2
D1
D
9
5
A1
4
C
SEATING
PLANE
B
A
0.08MM (0.0031") M C A-B S
B
SEE DETAIL A
b
6
7
WITH PLATING
7
(c)
c1
b1
BASE METAL
R
c
e/2
SECTION B-B
GAGE LINE
0.25MM (0.0098") BSC
0˚
-X-
PARALLEL TO
SEATING PLANE
L
X = A OR B
DETAIL A
Package
TSR 040
Jedec
MO-142 (B) EC
Symbol
A
A1
A2
b1
b
c1
c
D
D1
E
e
L
0
R
N
MIN
NOM
MAX
1.20
0.15
0.05
1.00
0.95
1.05
0.20
0.23
0.17
0.22
0.17
0.27
0.10
0.16
0.10
0.21
19.80 20.00 20.20
18.30 18.40 18.50
9.90 10.00 10.10
0.50 BASIC
0.50
0.70
0.60
3˚
0˚
5˚
0.08
0.20
40
DETAIL B
NOTES:
1
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (MM).
(DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982)
2
NOT APPLICABLE.
3
PIN 1 IDENTIFIER FOR REVERSE PIN OUT (DIE DOWN), INK OR LASER MARK.
4
TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS DEFINED AS THE PLANE OF
CONTACT THAT IS MADE WHEN THE PACKAGE LEADS ARE ALLOWED TO REST FREELY ON A FLAT
HORIZONTAL SURFACE.
5
DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE MOLD PROTUSION IS
0.15MM (.0059") PER SIDE.
6
DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE DAMBAR PROTUSION SHALL BE
0.08 (0.0031") TOTAL IN EXCESS OF b DIMENSION AT MAX. MATERIAL CONDITION. MINIMUM SPACE
BETWEEN PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 (0.0028").
7
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.10MM (.0039") AND
0.25MM (0.0098") FROM THE LEAD TIP.
8
LEAD COPLANARITY SHALL BE WITHIN 0.10MM (0.004") AS MEASURED FROM THE SEATING PLANE.
9
DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
3324 \ 16-038.10a
100
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Physical Dimensions
TS048—48-Pin Standard and Reverse Thin Small Outline Package (TSOP)
STANDARD PIN OUT (TOP VIEW)
A2
2
0.10 C
1
N
SEE DETAIL B
-A-
-BE 5
e
9
N
+1
2
N
2
D1
D
5
A1
4
C
SEATING
PLANE
B
A
0.08MM (0.0031") M C A-B S
B
SEE DETAIL A
b
6
7
WITH PLATING
7
(c)
c1
b1
BASE METAL
R
c
e/2
SECTION B-B
GAGE LINE
0.25MM (0.0098") BSC
0˚
-X-
PARALLEL TO
SEATING PLANE
L
X = A OR B
DETAIL A
Package
TS 048
Jedec
MO-142 (B) EC
Symbol
A
A1
A2
b1
b
c1
c
D
D1
E
e
L
0
R
N
MIN
NOM
MAX
1.20
0.15
0.05
1.00
0.95
1.05
0.20
0.23
0.17
0.22
0.17
0.27
0.10
0.16
0.10
0.21
19.80 20.00 20.20
18.30 18.40 18.50
11.90 12.00 12.10
0.50 BASIC
0.50
0.70
0.60
3˚
0˚
5˚
0.08
0.20
48
October 10, 2006 S29GL-M_00_B6
DETAIL B
NOTES:
1
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (MM).
(DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982)
2
PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP).
3
NOT APPLICABLE.
4
TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS DEFINED AS THE PLANE OF
CONTACT THAT IS MADE WHEN THE PACKAGE LEADS ARE ALLOWED TO REST FREELY ON A FLAT
HORIZONTAL SURFACE.
5
DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE MOLD PROTUSION IS
0.15MM (.0059") PER SIDE.
6
DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE DAMBAR PROTUSION SHALL BE
0.08 (0.0031") TOTAL IN EXCESS OF b DIMENSION AT MAX. MATERIAL CONDITION. MINIMUM SPACE
BETWEEN PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 (0.0028").
7
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.10MM (.0039") AND
0.25MM (0.0098") FROM THE LEAD TIP.
8
LEAD COPLANARITY SHALL BE WITHIN 0.10MM (0.004") AS MEASURED FROM THE SEATING PLANE.
9
DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
3325 \ 16-038.10a
S29GL-M MirrorBitTM Flash Family
101
D a t a
S h e e t
Physical Dimensions
TSR048—48-Pin Standard and Reverse Thin Small Outline Package (TSOP)
REVERSE PIN OUT (TOP VIEW)
A2
3
0.10 C
1
N
SEE DETAIL B
-A-
-BE 5
e
9
N
+1
2
N
2
D1
D
5
A1
4
C
SEATING
PLANE
B
A
0.08MM (0.0031") M C A-B S
B
SEE DETAIL A
b
6
7
WITH PLATING
7
(c)
c1
b1
BASE METAL
R
c
e/2
SECTION B-B
GAGE LINE
0.25MM (0.0098") BSC
0˚
-X-
PARALLEL TO
SEATING PLANE
L
X = A OR B
DETAIL A
Package
TSR 048
Jedec
MO-142 (B) EC
Symbol
A
A1
A2
b1
b
c1
c
D
D1
E
e
L
0
R
N
MIN
NOM
MAX
1.20
0.15
0.05
1.00
0.95
1.05
0.20
0.23
0.17
0.22
0.17
0.27
0.10
0.16
0.10
0.21
19.80 20.00 20.20
18.30 18.40 18.50
11.90 12.00 12.10
0.50 BASIC
0.50
0.70
0.60
3˚
0˚
5˚
0.08
0.20
48
DETAIL B
NOTES:
1
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (MM).
(DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982)
2
NOT APPLICABLE.
3
PIN 1 IDENTIFIER FOR REVERSE PIN OUT (DIE DOWN), INK OR LASER MARK.
4
TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS DEFINED AS THE PLANE OF
CONTACT THAT IS MADE WHEN THE PACKAGE LEADS ARE ALLOWED TO REST FREELY ON A FLAT
HORIZONTAL SURFACE.
5
DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE MOLD PROTUSION IS
0.15MM (.0059") PER SIDE.
6
DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE DAMBAR PROTUSION SHALL BE
0.08 (0.0031") TOTAL IN EXCESS OF b DIMENSION AT MAX. MATERIAL CONDITION. MINIMUM SPACE
BETWEEN PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 (0.0028").
7
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN 0.10MM (.0039") AND
0.25MM (0.0098") FROM THE LEAD TIP.
8
LEAD COPLANARITY SHALL BE WITHIN 0.10MM (0.004") AS MEASURED FROM THE SEATING PLANE.
9
DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
3326 \ 16-038.10a
102
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Physical Dimensions
TS056/TSR056—56-Pin Standard and Reverse Thin Small Outline Package (TSOP)
PACKAGE
JEDEC
SYMBOL
NOTES:
TS/TSR 56
MO-142 (B) EC
MIN.
NOM.
MAX.
1
CONTROLLING DIMENSIONS ARE IN MILLIMETERS (mm).
(DIMENSIONING AND TOLERANCING CONFORMS TO ANSI Y14.5M-1982.)
A
---
---
1.20
2
PIN 1 IDENTIFIER FOR STANDARD PIN OUT (DIE UP).
A1
0.05
---
0.15
3
PIN 1 IDENTIFIER FOR REVERSE PIN OUT (DIE DOWN), INK OR LASER MARK.
A2
0.95
1.00
1.05
4
b1
0.17
0.20
0.23
b
c1
0.17
0.10
0.22
---
0.27
0.16
TO BE DETERMINED AT THE SEATING PLANE -C- . THE SEATING PLANE IS
DEFINED AS THE PLANE OF CONTACT THAT IS MADE WHEN THE PACKAGE
LEADS ARE ALLOWED TO REST FREELY ON A FLAT HORIZONTAL SURFACE.
5
DIMENSIONS D1 AND E DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE
MOLD PROTUSION IS 0.15 mm PER SIDE.
6
DIMENSION b DOES NOT INCLUDE DAMBAR PROTUSION. ALLOWABLE
DAMBAR PROTUSION SHALL BE 0.08 mm TOTAL IN EXCESS OF b
DIMENSION AT MAX MATERIAL CONDITION. MINIMUM SPACE BETWEEN
PROTRUSION AND AN ADJACENT LEAD TO BE 0.07 mm.
7
THESE DIMESIONS APPLY TO THE FLAT SECTION OF THE LEAD BETWEEN
0.10 mm AND 0.25 mm FROM THE LEAD TIP.
8.
LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED FROM THE
SEATING PLANE.
9
DIMENSION "e" IS MEASURED AT THE CENTERLINE OF THE LEADS.
c
0.10
---
0.21
D
19.90
20.00
20.20
D1
18.30
18.40
18.50
E
13.90
14.00
14.10
0.50 BASIC
e
L
0.50
0.60
0.70
O
0˚
3˚
5˚
R
0.08
---
0.20
N
October 10, 2006 S29GL-M_00_B6
56
3160\38.10A
S29GL-M MirrorBitTM Flash Family
103
D a t a
S h e e t
Physical Dimensions
LAA064—64-Ball Fortified Ball Grid Array (FBGA)
104
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Physical Dimensions
LAC064—64-Pin 18 x 12 mm Package
D
0.20 C
2X
D1
A
eD
H
G
F
E
D
C
B
A
8
7
7
SE
6
eE
5
E1
E
.50
3
2
φ0
1.00±0.5
4
1
A1 CORNER ID.
(INK OR LASER)
1.00±0.5
A1
CORNER
B
6
0.20 C
2X
TOP VIEW
A1
CORNER
NXφb
SD
7
φ 0.25 M C A B
φ 0.10 M C
BOTTOM VIEW
0.25 C
A
A2
SEATING PLANE
A1
C
0.15 C
SIDE VIEW
NOTES:
PACKAGE
LAC 064
JEDEC
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994.
N/A
2. ALL DIMENSIONS ARE IN MILLIMETERS.
18.00 mm x 12.00 mm
PACKAGE
3. BALL POSITION DESIGNATION PER JESD 95-1, SPP-010 (EXCEPT
AS NOTED).
SYMBOL
MIN
NOM
MAX
A
---
---
1.40
NOTE
A1
0.40
---
---
STANDOFF
A2
0.60
---
---
BODY THICKNESS
PROFILE HEIGHT
D
18.00 BSC.
BODY SIZE
E
12.00 BSC.
BODY SIZE
7.00 BSC.
E1
7.00 BSC.
MD
8
MATRIX SIZE D DIRECTION
ME
8
MATRIX SIZE E DIRECTION
N
64
BALL COUNT
0.50
0.60
MATRIX FOOTPRINT
MATRIX FOOTPRINT
0.70
BALL DIAMETER
eD
1.00 BSC.
BALL PITCH - D DIRECTION
eE
1.00 BSC.
BALL PITCH - E DIRECTION
SD / SE
0.50 BSC.
SOLDER BALL PLACEMENT
NONE
e REPRESENTS THE SOLDER BALL GRID PITCH.
5. SYMBOL "MD" IS THE BALL ROW MATRIX SIZE IN THE
"D" DIRECTION.
SYMBOL "ME" IS THE BALL COLUMN MATRIX SIZE IN THE
"E" DIRECTION.
N IS THE TOTAL NUMBER OF SOLDER BALLS.
D1
φb
4.
DEPOPULATED SOLDER BALLS
6
DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL
DIAMETER IN A PLANE PARALLEL TO DATUM C.
7
SD AND SE ARE MEASURED WITH RESPECT TO DATUMS
A AND B AND DEFINE THE POSITION OF THE CENTER
SOLDER BALL IN THE OUTER ROW.
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN
THE OUTER ROW PARALLEL TO THE D OR E DIMENSION,
RESPECTIVELY, SD OR SE = 0.000.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN
THE OUTER ROW, SD OR SE = e/2
8. NOT USED.
9. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED
BALLS.
3243 \ 16-038.12d
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
105
D a t a
S h e e t
Physical Dimensions
FBA048—48-Pin 6.15 x 8.15 mm Package
Dwg rev AF; 10/99
106
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Physical Dimensions
FBC048—48-Pin 8 x 9 mm Package
Dwg rev AF; 10/99
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
107
D a t a
S h e e t
Physical Dimensions
FBE063—63-Pin 12 x 11 mm Package
Dwg rev AF; 10/99
108
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Physical Dimensions
FPT-48P-M19
LEAD No.
1
48
INDEX
Details of "A" part
0.25(.010)
0~8˚
0.60±0.15
(.024±.006)
24
25
* 12.00±0.20
20.00±0.20
(.787±.008)
* 18.40±0.20
(.724±.008)
"A"
(.472±.008)
+0.10
1.10 –0.05
+.004
.043 –.002
(Mounting
height)
0.10±0.05
(.004±.002)
(Stand off height)
0.50(.020)
0.10(.004)
+0.03
0.22±0.05
(.009±.002)
0.17 –0.08
+.001
.007 –.003
0.10(.004)
M
FPT-56P-M01
0.10±0.05
(.004±.002)
(Stand off)
LEAD No.
1
56
INDEX
0.22±0.05
(.009±.002)
0.10(.004)
M
*1 14.00±0.10
(.551±.004)
0.50(.020)
28
29
Details of "A" part
+0.10
1.10 –0.05
20.00±0.20(.787±.008)
+.004
.043 –.002
(Mounting height)
*2 18.40±0.10(.724±.004)
0.17±0.03
.007±.001
0.08(.003)
October 10, 2006 S29GL-M_00_B6
"A"
S29GL-M MirrorBitTM Flash Family
0˚~8˚
0.60±0.15
(.024±.006)
0.25(.010)
109
D a t a
S h e e t
Revision Summary
Revision A (January 29, 2004)
Initial Release.
Revision A1 (February 23, 2004)
Connection Diagrams
Removed 80-ball Fine-pitch BGA pinout.
Ordering Information
Added additional packing type.
Removed frame description from package material set.
Updated valid combinations to reflect the addition of new package type.
Added marking descriptions to all valid combination tables.
Word Program Command Sequence and Unlock Bypass
Command Sequence
Added these sections.
Figure 3, Write Buffer Programming Operation, Figure 4,
Program Operation
Updated figure.
Table 34, “Command Definitions( x16 Mode, BYTE# = VIH),” on
page 69
Updated table.
Added note 19.
Table 35, “Command Definitions (x8 Mode, BYTE# = VIL),” on
page 70
Updated table.
Added note 17.
Figure 7, Data# Polling Algorithm
Updated figure.
Erase and Program Operations and Alternate CE# Controlled
Erase and Program Operations
Updated TWHWHI description
Added Note 4.
Figure 16, Figure 18, Figure 20, Figure 24
Updated figure.
Physical Dimensions
Removed BGA-63P-M02 and BGA-80P-M01
Added the TS040 package
110
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Revision A2 (February 25, 2004)
Connection Diagrams
Removed the 40-pin reverse TSOP diagram.
Updated the 48-pin standard TSOP diagram.
Removed the 48-pin reverse TSOP diagram.
Removed the 56-pin reverse TSOP diagram.
Ordering Information
Removed all references to package type R.
Table 17 Autoselect Codes, (High Voltage Method)
Updated the R3, R4 column replacing -04 and -03 designators with -R4 and -R3 respectively.
Word Program Command Sequence
Included statements documenting word programming support for backward compatibility with
existing Flash drivers.
Physical Dimensions
Removed the BGA-80P-M02 diagram.
Revision A3 (February 26, 2004)
Distinctive Characteristics
Corrected typo in the Flexible Sector Architecture section.
Revision A4 (March 24, 2004)
CMOS Compatible
Removed VCC from Max for VOL.
Erase and Program Operations-S29GL256M only
Corrected unit typos.
Erase and Program Operations-S29GL128M only
Corrected the minimum Data Setup Time.
Alternate CE# Controlled Erase and Program Operations-S29GL128M
Corrected the minimum CE# Pulse width.
TSOP Pin and BGA Package Capacitance: Pkg types TB, TC, BB, BC
Added CIN3.
Connection Diagrams
40-pin standard TSOP: Corrected pin 30 to be VIO.
48-pin standard TSOP: Added superscripts to designators for pin 9, 13, 14, 15 and 47. Changed
pin 13 to A21. Added two notes below illustration.
56-pin standard TSOP: Added superscripts to designators for pin 1, 2 and 12. Changed pin 56 to
NC. Added three notes below illustration.
64-ball Fortified BGA: Corrected ball D8 to be VIO. Added superscripts to designators for ball D8,
F7, and F1. Added two notes below illustration.
63-ball Fine-pitch BGA: Added superscript to designator for Ball H7. Added one note below illustration. Added connection diagrams for S29GL064M (model R0) and S29GL032M (model R0).
Pin Description
Added VIO description.
Logic Symbols
Added VIO on all models except R3 and R4.
Figure 3 Write Buffer Programming Operation
Corrected the DQ locations and added callouts to notes one through three.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
111
D a t a
S h e e t
DC Characteristics
Corrected test conditions for ICC6.
Revision A5 (April 30, 2004)
Ordering Information - S29GL032M
Added R5 and R6 model numbers to the breakout table.
Updated the Valid Combinations for BGA packages table to reflect model numbers R5 and R6.
Ordering Information - S29GL064M
Revised R8 and R9 model numbers on the breakout table.
Updated the Valid Combinations for TSOP packages table.
Ordering Information - S29GL0128M
Added R8 and R9 model numbers to the breakout table.
Revised the Package Material Set options on the breakout table.
Updated the Valid Combinations for TSOP packages table.
Ordering Information - S29GL256M
Revised the Package Material Set options on the breakout table.
Connection Diagrams (56-Pin TSOP)
Added a callout to Note 3 for pin 15.
Device Geometry Definition table
Revised the data and description information for addresses: 28h/50h and
29h/52h.
Primary Vendor Specific Extended Query table
Revised the data and description information for addresses: 45h/8Ah (x16/x8)
Revised the data information for addresses: 4Ch/98h (x16/x8)
Erase and Programming Performance table
Revised notes 1 and 2 below the table.
Revision B0 (May 24, 2004)
Global
Converted to full datasheet status.
Figure 17, Autoselect Codes, (High Voltage Method)
Corrected typos in description.
Added values for R5, R6, R7 description for cycle 1-3.
Added R8 and R9 to Model Number.
Revision B1 (August 2, 2004)
Ordering Information-S29GL032M
Added the following temperature range: “C = Commercial (0°C to +70°C)'.
Commercial temperature range options added for 90ns speeds.
Global Change
S29GL032M, S29GL064M, S29GL128M, S29GL236M ordering options pages:
Updated note 3 with the following “...TSOPs can be packed in Types 0 and 3; BGAs can be packed
in Types 0, 2, or 3.
Revision B2 (September 8, 2004)
Connection Diagram - 64-ball Fortified BGA
Modified note 4.
112
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006
D a t a
S h e e t
Logic Symbol-S29GL032M (Models R3, R4)
Added models R5 and R6 to the logic symbol.
Logic Symbol-S29GL064M (Models R1, R2)
Added models R8 & R9 to the logic symbol.
S29GL032M Valid Combinations
Corrected ordering part numbers for LAA064 packages.
Physical Dimensions
Renamed the BGA-48P-M20 package as the FBG048 package.
Ordering Information
Added footnotes to indicate TSOP Pb-free leadframe plating.
Revision B3 (October 9, 2004)
General
Updated all references to Figures, Tables, and Headings to reflect page number (active link)
Updated tables 20, 21, and 22
Updated tables 24, 25, and 26
S29GL064M Valid combination
Corrected ordering part numbers for TS056 packages
S29GL032M Sector Protection/Uprotection Address Tables
Corrected table titles
S29GL064M Sector Protection/Uprotection Address Tables
Corrected table titles
Primary Vendor-Specific Extended Query
Corrected CFI data at address 48h/90h to be 0001h
DC Characteristics
Updated note 2
Figure 15, Reset Timing
Added tRH
Revision B4 (January 10, 2005)
Secured Sector Flash Memory Region
Updated Secured Silicon Sector address table with addresses in x8-mode
DC Characteristics, CMOS Compatible
Corrected WP#/ACC input load current footnote
Document
Updated cross-references and format.
Valid Combination Tables
Added notes to the 128 Mb and 256 Mb combination tables.
Revision B5 (December 13, 2005)
Added Supersession text.
Corrected typos on connection diagrams and in CFI table.
October 10, 2006 S29GL-M_00_B6
S29GL-M MirrorBitTM Flash Family
113
D a t a
S h e e t
Revision B6 (October 10, 2006)
Global
Deleted FBG048 package from S29GL032M device. Added “retired product” status text to cover
page, and first page and Ordering Information sections of data sheet.
Colophon
The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary
industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for any use that
includes fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal
injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control,
medical life support system, missile launch control in weapon system), or (2) for any use where chance of failure is intolerable (i.e., submersible repeater and
artificial satellite). Please note that Spansion will not be liable to you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures
by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other
abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under
the Foreign Exchange and Foreign Trade Law of Japan, the US Export Administration Regulations or the applicable laws of any other country, the prior authorization by the respective government entity be required for export of those products.
Trademarks and Notice
The contents of this document are subject to change without notice. This document may contain information on a Spansion product under development by
Spansion Inc. Spansion Inc. reserves the right to change or discontinue work on any product without notice. The information in this document is provided
as is without warranty or guarantee of any kind as to its accuracy, completeness, operability, fitness for particular purpose, merchantability, non-infringement
of third-party rights, or any other warranty, express, implied, or statutory. Spansion Inc. assumes no liability for any damages of any kind arising out of the
use of the information in this document.
Copyright © 2004–2006 Spansion Inc. All rights reserved. Spansion, the Spansion logo, MirrorBit, ORNAND, HD-SIM, and combinations thereof, are trademarks of Spansion Inc. Other company and product names used in this publication are for identification purposes only and may be trademarks of their respective companies.
114
S29GL-M MirrorBitTM Flash Family
S29GL-M_00_B6 October 10, 2006