SPECIFICATION FOR APPROVAL REF : PAGE: 1 PROD. NAME ABC'S DWG NO. SMD POWER INDUCTOR SB0805□□□□L□-□□□ ABC'S ITEM NO. Ⅰ﹒CONFIGURATION & DIMENSIONS： A 101 A B C D E F G H I Marking dot is start winding & Inductance code C B F m/m m/m m/m m/m m/m m/m m/m m/m m/m D E H D : 8.0±0.3 : 10.5±0.3 : 5.0±0.3 : 2.1±0.2 : 2.0±0.2 : 6.0±0.3 : 5.7 ref. : 2.2 ref. : 2.4 ref. I G I ( PCB Pattern ) Ⅱ﹒SCHEMATIC DIAGRAM： a Ⅲ﹒MATERIALS： a﹒Core：Ferrite DR core b b﹒Wire：Enamelled copper wire （class F） c c﹒Base：LCP E4008 d d﹒Terminal：Cu/Ni/Sn e Peak Temp：260℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. e﹒Adhesive：Epoxy resin f﹒Solder wire：Sn97/Cu3 Alloys g﹒Remark：Products comply with RoHS' requirements Temperatu re Rising Area Pre heat Area +4.0℃ / sec max. 150 ~ 200 ℃ / 60 ~ 120sec Reflow Area +2.0 ~ 4.0 ℃ / sec max. Forced Coo ling Area -(1 .0 ~ 5 .0)℃ / sec max. Peak Temperature: 260℃ 250 Ⅳ﹒GENERAL SPECIFICATION： a﹒Temp. rise 40℃ max. b﹒Storage temp.：-40℃ ~ +125℃ c﹒Operating temp.：-40℃ ~ +105℃ d﹒Resistance to solder heat：260℃. 10 secs. AR-001A Temperature ( ℃ ) 50s ec max. 230℃ 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : PAGE: 2 PROD. ABC'S DWG NO. SMD POWER INDUCTOR NAME SB0805□□□□L□-□□□ ABC'S ITEM NO. Ⅴ﹒ELECTRICAL CHARACTERISTICS： Dwg. No. Inductance (uH) 0.1 V / 100 KHz RDC (Ω) max. Irms (A) max. Isat (A) typ. SB08053R3ML□-□□□ 3.3±20% 0.022 5.00 5.20 SB08054R7ML□-□□□ 4.7±20% 0.028 4.20 4.00 SB08056R8ML□-□□□ 6.8±20% 0.040 3.40 3.40 SB0805100ML□-□□□ 10.0±20% 0.050 3.00 2.80 SB0805150ML□-□□□ 15.0±20% 0.070 2.40 2.30 SB0805220ML□-□□□ 22.0±20% 0.100 2.00 1.85 SB0805330ML□-□□□ 33.0±20% 0.145 1.72 1.54 SB0805470YL□-□□□ 47.0±15% 0.200 1.40 1.28 SB0805680YL□-□□□ 68.0±15% 0.270 1.20 1.15 SB0805101YL□-□□□ 100.0±15% 0.400 1.00 0.92 SB0805151YL□-□□□ 150.0±15% 0.560 0.75 0.75 SB0805221YL□-□□□ 220.0±15% 0.860 0.62 0.62 SB0805331YL□-□□□ 330.0±15% 1.500 0.46 0.50 1). □：Packaging information … A：Bulk 2)."- □□□ ":Reference code B：Taping Reel @ Inductance VS. DC Current Curve 3). Irms base on Temp. rise 40℃ max. 10 3 7 5 4). Isat base on △L / L0A=10% typ. 3 Inductance（uH） 2 221 10 2 7 5 101 3 330 2 10 1 7 5 100 3 3R3 2 10 0 10 1 2 3 5 7 10 2 2 3 5 7 10 3 DC Current (mA) AR-001A 2 3 5 7 10 4 SPECIFICATION FOR APPROVAL REF : PAGE: 3 PROD. NAME ABC'S DWG NO. SMD POWER INDUCTOR SB0805□□□□L□-□□□ ABC'S ITEM NO. Ⅵ﹒PACKAGING INFORMATION： 1. Configuration : T Cover tape N B A 2.0±0.5 D ∮C ∮C G Embossed carrier ※Carrier tape width：D P:12 m/m 4 m/m End Start 101 101 101 101 101 Leader no component 200 m/m Min. Trailer no component 400 m/m Min. Components User direction of feed 2. Dimensions Unit:m/m Style A 13 - 24 330 B 21±0.8 C D 13±0.5 24 G 26 +0 N 50 -0 T 30.4 3. Q'TY & G.W. Per package Inner : Reel Series SB0805 AR-001A Q'TY (pcs) G.W. (gw) 800 880 Outer : Carton Style 13 - 24 Q'TY (pcs) 3,200 G.W. (Kg) 4.5 Size (cm) 40 x 40 x 24 SPECIFICATION FOR APPROVAL REF : PAGE: 4 PROD. ABC'S DWG NO. SMD POWER INDUCTOR NAME SB0805□□□□L□-□□□ ABC'S ITEM NO. Ⅶ﹒DWGING NUMBER EXPRESSION： B S 0 8 0 5 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package Inner package Q'TY A T.B.D. T.B.D. B T / R ( Reel package ) 800 pcs Remark SPECIFICATION FOR APPROVAL REF : PAGE: 5 PROD. NAME ABC'S DWG NO. SMD POWER INDCTOR SB0805□□□□L□-□□□ ABC'S ITEM NO. Ⅷ﹒RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 95% of the terminal electrode Shall be covered With fresh solder. Preheat : 155℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes -40 ℃ 30 minutes Room temp. 15 minutes +105 ℃ Total : 50 cycles Humidity Test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 105±5℃ Applied current : Per spec. Time : 96 hours AR-001A 30 minutes SPECIFICATION FOR APPROVAL PAGE: 6 REF : PROD. NAME ABC'S DWG NO. SMD POWER INDUCTOR SB0805□□□□L□-□□□ ABC'S ITEM NO. Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Coat Typ Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyamideimide Polyamide Modified Epoxy ____ ____ Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Modified Polyester Polyurethane SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 ANSI Type Temp Class MW81-C MW75C MW35C ___ ___ 220 130 200 180 200 ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ Mark Dsg ____ ____ ____ ____ ____ ____ BC Coat Typ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane 220 200 155 155 130 155 155 155 180 155 155 155 180 180 MW26C MW79 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Page 1 of 2 287806002 Mtl Dsg OC ____ ____ OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type Temp Class MW80C MW2-C ___ 155 105 130 130 130 130 MW75C MW28-C MW28-C @-May be suffixed by LZ; # - May be suffixed b y LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat o verall. Marking: Company name or trademarks Recognized Component Mark. or 榮星電線 , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equip ment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AR-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000 SPECIFICATION FOR APPROVAL PAGE: 7 REF : PROD. NAME ABC'S DWG NO. SMD POWER INDUCTOR SB0805□□□□L□-□□□ ABC'S ITEM NO. E54705 (M) H D RTI Min UL94 H H C V 4 Elec Mech Thk Flame w/o W A 9 T with T Mtl Dsg Col mm Imp I Class I I R 5 Imp Liquid crystal plyester (LCP), designated "EKONOL" or "SUMIKASUPER", furnished in the form of pellets, (Contd) E4008 , E400X E4008 NC , BK NC , WT , BK E4010 E400(Y)L , E4008L E4810 AR-001A NC , BK NC , BK NC , BK 0.30 0.75 1.5 3.0 0.30 0.75 1.5 3.0 0.30 0.75 1.5 3.0 0.30 0.75 1.5 3.0 0.30 0.75 1.5 3.0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 94V-0 130 130 130 130 130 220 220 220 130 220 220 220 130 130 130 130 130 130 130 130 130 130 130 130 130 180 200 200 130 180 200 200 130 130 130 130 130 130 130 130 130 130 130 130 130 220 240 240 130 220 240 240 130 130 130 130 130 130 130 130 ___ ___ 3 2 1 ___ 4 4 4 ___ 3 2 1 ___ 4 4 4 ___ 3 2 1 ___ 4 4 4 ___ 3 2 1 ___ 4 4 4 ___ 0 0 1 4 4 4 ___ ___ ___ ___ ___ ___ ___ ___ ___ 0 ___ ___ ___ 5 ___ ___ ___ 4 ___ ___ ___ 0 ___ ___ ___ 5 ___ ___ ___ 4 ___ ___ ___ 0 ___ ___ ___ 5 ___ ___ ___ 4 ___ ___ ___ 0 ___ ___ ___ 5 ___ ___ ___ 4 ___ ___ ___ 0 5 4