SN74ALVC162836 20-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS www.ti.com SCES129E – MARCH 1998 – REVISED OCTOBER 2004 FEATURES • • • • • • • • DGG, DGV, OR DL PACKAGE (TOP VIEW) Member of the Texas Instruments Widebus™ Family Operates From 1.65 V to 3.6 V Max tpd of 4 ns at 3.3 V ±12-mA Output Drive at 3.3 V Output Port Has Equivalent 26-Ω Series Resistors, So No External Resistors Are Required Designed to Comply With JEDEC 168-Pin and 200-Pin SDRAM Buffered DIMM Specification Latch-Up Performance Exceeds 250 mA Per JESD 17 ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-A) – 200-V Machine Model (A115-A) – 1000-V Charged-Device Model (C101) OE Y1 Y2 GND Y3 Y4 VCC Y5 Y6 Y7 GND Y8 Y9 Y10 Y11 Y12 Y13 GND Y14 Y15 Y16 VCC Y17 Y18 GND Y19 Y20 NC DESCRIPTION/ORDERING INFORMATION This 20-bit universal bus driver is designed for 1.65-V to 3.6-V VCC operation. Data flow from A to Y is controlled by the output-enable (OE) input. The device operates in the transparent mode when the latch-enable (LE) input is low. When LE is high, the A data is latched if the clock (CLK) input is held at a high or low logic level. If LE is high, the A data is stored in the latch/flip-flop on the low-to-high transition of CLK. When OE is high, the outputs are in the high-impedance state. The output port includes equivalent 26-Ω series resistors to reduce overshoot and undershoot. 1 56 2 55 3 54 4 53 5 52 6 51 7 50 8 49 9 48 10 47 11 46 12 45 13 44 14 43 15 42 16 41 17 40 18 39 19 38 20 37 21 36 22 35 23 34 24 33 25 32 26 31 27 30 28 29 CLK A1 A2 GND A3 A4 VCC A5 A6 A7 GND A8 A9 A10 A11 A12 A13 GND A14 A15 A16 VCC A17 A18 GND A19 A20 LE NC − No internal connection To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION PACKAGE (1) TA (1) TOP-SIDE MARKING SN74ALVC162836DL Tape and reel SN74ALVC162836DLR TSSOP - DGG Tape and reel SN74ALVC162836DGGR ALVC162836 TVSOP - DGV Tape and reel SN74ALVC162836DGVR VC2836 SSOP - DL -40°C to 85°C ORDERABLE PART NUMBER Tube ALVC162836 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 1998–2004, Texas Instruments Incorporated SN74ALVC162836 20-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS www.ti.com SCES129E – MARCH 1998 – REVISED OCTOBER 2004 FUNCTION TABLE INPUTS (1) OE LE CLK A OUTPUT Y H X X X Z L L X L L L L X H H L H ↑ L L L H ↑ H H L H L or H X Y0 (1) Output level before the indicated steady-state input conditions were established, provided that CLK is high before LE goes high LOGIC DIAGRAM (POSITIVE LOGIC) 1 OE 56 CLK LE 29 55 1D A1 C1 2 Y1 CLK To 19 Other Channels ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range -0.5 4.6 V VI Input voltage range (2) -0.5 4.6 V -0.5 VCC + 0.5 range (2) (3) UNIT VO Output voltage IIK Input clamp current VI < 0 -50 mA IOK Output clamp current VO < 0 -50 mA IO Continuous output current ±50 mA ±100 mA Continuous current through each VCC or GND θJA Package thermal impedance (4) Tstg Storage temperature range DGG package 64 DGV package 48 DL package (1) (2) (3) (4) 2 V °C/W 56 -65 150 °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. This value is limited to 4.6 V maximum. The package thermal impedance is calculated in accordance with JESD 51-7. SN74ALVC162836 20-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS www.ti.com SCES129E – MARCH 1998 – REVISED OCTOBER 2004 RECOMMENDED OPERATING CONDITIONS (1) VCC Supply voltage VCC = 1.65 V to 1.95 V VIH High-level input voltage MIN MAX 1.65 3.6 Low-level input voltage VI Input voltage VO Output voltage IOH High-level output current VCC = 2.3 V to 2.7 V 1.7 VCC = 2.7 V to 3.6 V 2 V 0.35 × VCC VCC = 2.3 V to 2.7 V 0.7 VCC = 2.7 V to 3.6 V 0.8 Low-level output current ∆t/∆v Input transition rise or fall rate TA Operating free-air temperature 3.6 V 0 VCC V VCC = 1.65 V -2 VCC = 2.3 V -6 VCC = 2.7 V -8 mA -12 VCC = 1.65 V 2 VCC = 2.3 V 6 VCC = 2.7 V 8 VCC = 3 V (1) V 0 VCC = 3 V IOL V 0.65 × VCC VCC = 1.65 V to 1.95 V VIL UNIT mA 12 -40 10 ns/V 85 °C All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. ELECTRICAL CHARACTERISTICS over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOH = -100 µA VOH 1.65 V to 3.6 V MIN 1.65 V 1.2 IOH = -4 mA 2.3 V 1.9 2.3 V 1.7 3V 2.4 IOH = -8 mA TYP (1) MAX V 2.7 V 2 IOH = -12 mA 3V 2 IOL = 100 µA 1.65 V to 3.6 V 0.2 IOL = 2 mA 1.65 V 0.45 IOL = 4 mA 2.3 V 0.4 2.3 V 0.55 3V 0.55 2.7 V 0.6 3V 0.8 IOL = 6 mA IOL = 8 mA IOL = 12 mA UNIT VCC - 0.2 IOH = -2 mA IOH = -6 mA VOL VCC V II VI = VCC or GND 3.6 V ±5 µA IOZ VO = VCC or GND 3.6 V ±10 µA ICC VI = VCC or GND, IO = 0 3.6 V 40 µA ∆ICC One input at VCC - 0.6 V, Other inputs at VCC or GND 3 V to 3.6 V 750 µA Ci Co (1) Control inputs Data inputs Outputs VI = VCC or GND 3.3 V VO = VCC or GND 3.3 V 5 5.5 7.5 pF pF All typical values are at VCC = 3.3 V, TA = 25°C. 3 SN74ALVC162836 20-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS www.ti.com SCES129E – MARCH 1998 – REVISED OCTOBER 2004 TIMING REQUIREMENTS over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) VCC = 1.8 V MIN MAX fclock tw tsu th (1) Setup time Hold time MIN (1) Clock frequency Pulse duration VCC = 2.5 V ± 0.2 V VCC = 3.3 V ± 0.3 V VCC = 2.7 V MAX MIN MAX 150 MIN 150 150 LE low (1) 3.3 3.3 3.3 CLK high or low (1) 3.3 3.3 3.3 Data before CLK↑ (1) 1.4 1.7 1.5 CLK high (1) 1.2 1.6 1.3 CLK low (1) 1.4 1.5 1.2 (1) 0.9 0.9 0.9 (1) 1.1 1.1 1.1 Data before LE↑ Data after CLK↑ Data after LE↑ CLK high or low UNIT MAX MHz ns ns ns This information was not available at the time of publication. SWITCHING CHARACTERISTICS over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) MIN TYP (1) fmax A tpd LE Y CLK (1) VCC = 1.8 V VCC = 2.5 V ± 0.2 V VCC = 2.7 V VCC = 3.3 V ± 0.3 V MIN MIN MIN MAX 150 MAX 150 150 MHz (1) 1 4.4 4.6 1.2 4 (1) 5.1 1.1 5.8 6.1 1.4 (1) UNIT MAX ns 1 5.2 5.5 1.1 5 ten OE Y (1) 1.1 6.4 6.5 1.2 5.5 ns tdis OE Y (1) 1 4.7 5.2 1.7 5.1 ns This information was not available at the time of publication. SWITCHING CHARACTERISTICS from 0°C to 65°C, CL = 50 pF FROM (INPUT) PARAMETER A tpd VCC = 3.3 V ± 0.15 V TO (OUTPUT) MIN Y CLK UNIT MAX 1 4 1.7 4.5 ns OPERATING CHARACTERISTICS TA = 25°C PARAMETER Cpd Power dissipation capacitance (1) 4 TEST CONDITIONS Outputs enabled Outputs disabled CL = 0, This information was not available at the time of publication. f = 10 MHz VCC = 1.8 V VCC = 2.5 V VCC = 3.3 V TYP TYP TYP (1) 31 36 (1) 7 11 UNIT pF SN74ALVC162836 20-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS www.ti.com SCES129E – MARCH 1998 – REVISED OCTOBER 2004 PARAMETER MEASUREMENT INFORMATION VLOAD S1 RL From Output Under Test Open GND CL (see Note A) RL TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open VLOAD GND LOAD CIRCUIT INPUT VCC 1.8 V 2.5 V ± 0.2 V 2.7 V 3.3 V ± 0.3 V VI tr/tf VCC VCC 2.7 V 2.7 V ≤2 ns ≤2 ns ≤2.5 ns ≤2.5 ns VM VLOAD CL RL V∆ VCC/2 VCC/2 1.5 V 1.5 V 2 × VCC 2 × VCC 6V 6V 30 pF 30 pF 50 pF 50 pF 1 kΩ 500 Ω 500 Ω 500 Ω 0.15 V 0.15 V 0.3 V 0.3 V tw VI Timing Input VM VM VM 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VM VM 0V tPLH Output Control (low-level enabling) tPLZ VLOAD/2 VM tPZH VOH VM VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VM 0V Output Waveform 1 S1 at VLOAD (see Note B) tPHL VM VI VM tPZL VI Input VOLTAGE WAVEFORMS PULSE DURATION th VI Data Input VM 0V 0V tsu Output VI VM Input Output Waveform 2 S1 at GND (see Note B) VOL + V∆ VOL tPHZ VOH VM VOH − V∆ 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 5 PACKAGE OPTION ADDENDUM www.ti.com 6-Dec-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 74ALVC162836DGGRE4 ACTIVE TSSOP DGG 56 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ALVC162836DGVRE4 ACTIVE TVSOP DGV 56 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ALVC162836DLG4 ACTIVE SSOP DL 56 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ALVC162836DLRG4 ACTIVE SSOP DL 56 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVC162836DGGR ACTIVE TSSOP DGG 56 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVC162836DGVR ACTIVE TVSOP DGV 56 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVC162836DL ACTIVE SSOP DL 56 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVC162836DLR ACTIVE SSOP DL 56 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 20 20 Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0°–8° 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins – MO-153 14/16/20/56 Pins – MO-194 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MSSO001C – JANUARY 1995 – REVISED DECEMBER 2001 DL (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0.025 (0,635) 0.0135 (0,343) 0.008 (0,203) 48 0.005 (0,13) M 25 0.010 (0,25) 0.005 (0,13) 0.299 (7,59) 0.291 (7,39) 0.420 (10,67) 0.395 (10,03) Gage Plane 0.010 (0,25) 1 0°–ā8° 24 0.040 (1,02) A 0.020 (0,51) Seating Plane 0.110 (2,79) MAX 0.004 (0,10) 0.008 (0,20) MIN PINS ** 28 48 56 A MAX 0.380 (9,65) 0.630 (16,00) 0.730 (18,54) A MIN 0.370 (9,40) 0.620 (15,75) 0.720 (18,29) DIM 4040048 / E 12/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). Falls within JEDEC MO-118 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS003D – JANUARY 1995 – REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated