SN74BCT29823 9-BIT BUS-INTERFACE FLIP-FLOP WITH 3-STATE OUTPUTS SCBS018D – NOVEMBER 1988 – REVISED NOVEMBER 1993 • • • • DW OR NT PACKAGE (TOP VIEW) State-of-the-Art BiCMOS Design Significantly Reduces ICCZ ESD Protection Exceeds 2000 V Per MIL-STD-883C, Method 3015; Exceeds 200 V Using Machine Model (C = 200 pF, R = 0) 3-State Buffer-Type Outputs Drive Bus Lines Directly Package Options Include Plastic Small-Outline (DW) Packages and Standard Plastic 300-mil DIPs (NT) OE 1D 2D 3D 4D 5D 6D 7D 8D 9D CLR GND description This 9-bit bus-interface flip-flop features 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. It is particularly suitable for implementing wider buffer registers, I/O ports, bidirectional bus drivers with parity, and working registers. 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 VCC 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q 9Q CLKEN CLK The nine flip-flops are edge-triggered D-type flip-flops. With the clock-enable (CLKEN) input low, the flip-flops store data on the low-to-high transitions of the clock. Taking CLKEN high disables the clock buffer, thus latching the outputs. The SN74BCT29823 has noninverting data (D) inputs. Taking the clear (CLR) input low causes the nine Q outputs to go low independent of the clock. A buffered output-enable (OE) input can be used to place the nine outputs in either a normal logic state (high or low) or a high-impedance state. In the high-impedance state, the outputs neither load nor drive the bus lines significantly. The high-impedance state and increased drive provide the capability to drive bus lines without need for interface or pullup components. The output enable (OE) does not affect the internal operation of the flip-flops. Old data can be retained or new data can be entered while the outputs are in the high-impedance state. The SN74BCT29823 is characterized for operation from 0°C to 70°C. FUNCTION TABLE (each flip-flop) INPUTS OE CLR CLKEN CLK D OUTPUT Q L L X X X L L H L ↑ H H L H L ↑ L L L H H X X Q0 H X X X X Z Copyright 1993, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 2–1 SN74BCT29823 9-BIT BUS-INTERFACE FLIP-FLOP WITH 3-STATE OUTPUTS SCBS018D – NOVEMBER 1988 – REVISED NOVEMBER 1993 logic symbol† OE CLR CLKEN CLK 1D 2D 3D 4D 5D 6D 7D 8D 9D 1 EN 11 R 14 G1 13 1C2 2 23 2D 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 1Q 2Q 3Q 4Q 5Q 6Q 7Q 8Q 9Q † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. logic diagram (positive logic) OE CLR CLKEN CLK 1 11 14 R 13 C1 1D 2 1D To Eight Other Channels 2–2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 23 1Q SN74BCT29823 9-BIT BUS-INTERFACE FLIP-FLOP WITH 3-STATE OUTPUTS SCBS018D – NOVEMBER 1988 – REVISED NOVEMBER 1993 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V Voltage range applied to any output in the disabled or power-off state, VO . . . . . . . . . . . . . . . . – 0.5 V to 5.5 V Voltage range applied to any output in the high state, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 30 mA Current into any output in the low state, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA Operating free-air temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. recommended operating conditions MIN NOM MAX 4.5 5 5.5 UNIT VCC VIH Supply voltage VIL IIK Low-level input voltage 0.8 V Input clamp current –18 mA IOH IOL High-level output current – 24 mA Low-level output current 48 mA TA Operating free-air temperature 70 °C High-level input voltage 2 V V 0 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK TEST CONDITIONS VCC = 4.5 V, II = –18 mA IOH = – 15 mA VOH VCC = 4 4.5 5V VOL II VCC = 4.5 V, VCC = 5.5 V, IIH IIL VCC = 5.5 V, VCC = 5.5 V, IOS§ IOZH VCC = 5.5 V, VCC = 5.5 V, IOZL ICCL VCC = 5.5 V, VCC = 5.5 V, Outputs open ICCH ICCZ VCC = 5.5 V, VCC = 5.5 V, Outputs open Outputs open Ci VCC = 5 V, VCC = 5 V, VI = 2.5 V or 0.5 V VO = 2.5 V or 0.5 V Co IOH = – 24 mA IOL = 48 mA VI = 7 V VI = 2.7 V VI = 0.5 V VO = 0 MIN TYP‡ 2.4 3.2 MAX UNIT –1.2 V V 2 0.35 –10 –75 0.5 V 0.1 mA –75 µA – 0.2 mA – 250 mA 20 µA – 20 µA 25 35 mA 6 10 mA 2 6 mA VO = 2.7 V VO = 0.5 V 5.5 pF 7 pF ‡ All typical values are at VCC = 5 V, TA = 25°C. § Not more than one output should be tested at a time, and the duration of the test should not exceed one second. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 2–3 SN74BCT29823 9-BIT BUS-INTERFACE FLIP-FLOP WITH 3-STATE OUTPUTS SCBS018D – NOVEMBER 1988 – REVISED NOVEMBER 1993 timing requirements over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) VCC = 5 V, TA = 25°C fclock Clock frequency tw Pulse duration tsu th Setup time before CLK↑ ↑ Hold time after CLK↑ MIN MAX 0 125 MIN MAX UNIT 0 125 MHz CLR low 6 6 CLK high or low 7 7 CLR inactive 2 2 Data high or low 7 7 CLKEN high 6 6 CLKEN low 8 8 Data high or low 1 1 CLKEN high or low 0 0 ns ns ns switching characteristics over recommended ranges of supply voltage and operating free-air temperature, CL = 50 pF (unless otherwise noted) (see Note 2) PARAMETER fmax tPLH FROM (INPUT) TO (OUTPUT) Q CLR Q tPZH tPZL OE Q tPHZ tPLZ OE Q NOTE 2: Load circuits and voltage waveforms are shown in Section 1. 2–4 MIN TYP MIN POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MAX UNIT MAX 125 CLK tPHL tPHL VCC = 5 V, TA = 25°C 125 MHz 1.5 7.5 10 1.5 12 1.5 6.5 9 1.5 10 1.5 7.5 10 1.5 12 2 7.5 10 2 12 2 9 12 2 13 2 5 7 2 8 2 5 7 2 8 ns ns ns ns IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated