SN74CBT16210 20-BIT FET BUS SWITCH SCDS033C – APRIL 1997 – REVISED MAY 1998 D D D 5-Ω Switch Connection Between Two Ports TTL-Compatible Input Levels Package Options Include Plastic 300-mil Shrink Small-Outline (DL), Thin Shrink Small-Outline (DGG), and Thin Very Small-Outline (DGV) Packages DGG, DGV, OR DL PACKAGE (TOP VIEW) NC 1A1 1A2 1A3 1A4 1A5 1A6 GND 1A7 1A8 1A9 1A10 2A1 2A2 VCC 2A3 GND 2A4 2A5 2A6 2A7 2A8 2A9 2A10 description The SN74CBT16210 provides 20 bits of high-speed TTL-compatible bus switching. The low on-state resistance of the switch allows connections to be made with minimal propagation delay. The device is organized as a dual 10-bit bus switch with separate output-enable (OE) inputs. It can be used as two 10-bit bus switches or as one 20-bit bus switch. When OE is low, the associated 10-bit bus switch is on and port A is connected to port B. When OE is high, the switch is open, and a high-impedance state exists between the ports. The SN74CBT16210 is characterized operation from –40°C to 85°C. for FUNCTION TABLE (each 10-bit bus switch) INPUT OE FUNCTION L A port = B port H Disconnect 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 1OE 2OE 1B1 1B2 1B3 1B4 1B5 GND 1B6 1B7 1B8 1B9 1B10 2B1 2B2 2B3 GND 2B4 2B5 2B6 2B7 2B8 2B9 2B10 NC – No internal connection logic diagram (positive logic) 1A1 2 46 12 36 1A10 1B1 1B10 48 1OE 2A1 13 35 24 25 2A10 2B1 2B10 47 2OE Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1998, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN74CBT16210 20-BIT FET BUS SWITCH SCDS033C – APRIL 1997 – REVISED MAY 1998 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Continuous channel current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –50 mA Package thermal impedance, θJA (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89°C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93°C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51. recommended operating conditions (see Note 3) MIN MAX 5.5 VCC VIH Supply voltage 4 High-level control input voltage 2 VIL TA Low-level control input voltage Operating free-air temperature –40 UNIT V V 0.8 V 85 °C NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK II ICC ∆ICC§ Control inputs Ci Control inputs Cio(OFF) TEST CONDITIONS VCC = 4.5 V, VCC = 0 V, II = –18 mA VI = 5.5 V VCC = 5.5 V, VCC = 5.5 V, VI = 5.5 V or GND IO = 0, VCC = 5.5 V, VI = 3 V or 0 One input at 3.4 V, VO = 3 V or 0, VCC = 4 V, TYP at VCC = 4 V OE = VCC ron¶ VCC = 4.5 V MIN TYP‡ MAX UNIT –1.2 V 10 ±1 VI = VCC or GND Other inputs at VCC or GND µA 3 µA 2.5 mA 4.5 pF 5.5 pF VI = 2.4 V, II = 15 mA 14 20 VI = 0 II = 64 mA II = 30 mA 5 7 5 7 Ω VI = 2.4 V, II = 15 mA 8 12 ‡ All typical values are at VCC = 5 V (unless otherwise noted), TA = 25°C. § This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. ¶ Measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-state resistance is determined by the lowest voltage of the two (A or B) terminals. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN74CBT16210 20-BIT FET BUS SWITCH SCDS033C – APRIL 1997 – REVISED MAY 1998 switching characteristics over recommended operating free-air temperature range, CL = 50 pF (unless otherwise noted) (see Figure 1) VCC = 4 V VCC = 5 V ± 0.5 V MIN MIN FROM (INPUT) TO (OUTPUT) tpd† A or B B or A 0.35 ten OE A or B 9.3 PARAMETER MAX UNIT MAX 3.3 0.25 ns 8.6 ns tdis OE A or B 7.1 2.8 7.9 ns † The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). PARAMETER MEASUREMENT INFORMATION 7V S1 500 Ω From Output Under Test Open GND CL = 50 pF (see Note A) 500 Ω TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 7V Open 3V Output Control (low-level enabling) LOAD CIRCUIT 1.5 V 1.5 V 0V tPZL 3V Input 1.5 V 1.5 V 0V tPLH 1.5 V 1.5 V tPZH tPHL VOH Output tPLZ Output Waveform 1 S1 at 7 V (see Note B) 1.5 V VOL Output Waveform 2 S1 at Open (see Note B) VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES 3.5 V VOL + 0.3 V VOL tPHZ 1.5 V VOH VOH – 0.3 V 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated