SN54F240, SN74F240 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SDFS061A – D2932, MARCH 1987 – REVISED OCTOBER 1993 • SN54F240 . . . J PACKAGE SN74F240 . . . DB, DW, OR N PACKAGE (TOP VIEW) 3-State Outputs Drive Bus Lines or Buffer Memory Address Registers Package Options Include Plastic Small-Outline (SOIC) and Shrink Small-Outline (SSOP) Packages, Ceramic Chip Carriers, and Plastic and Ceramic DIPs 1OE 1A1 2Y4 1A2 2Y3 1A3 2Y2 1A4 2Y1 GND description These octal buffers and line drivers are designed specifically to improve both the performance and density of 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters. Taken together with the ′F241 and ′F244, these devices provide the choice of selected combinations of inverting and noninverting outputs, symmetrical OE (active-low output-enable) inputs, and complementary OE and OE inputs. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC 2OE 1Y1 2A4 1Y2 2A3 1Y3 2A2 1Y4 2A1 2Y4 1A1 1OE VCC SN54F240 . . . FK PACKAGE (TOP VIEW) The ′F240 is organized as two 4-bit buffers/line drivers with separate output enable (OE) inputs. When OE is low, the device passes data from the A inputs to the Y outputs. When OE is high, the outputs are in the high-impedance state. 1A2 2Y3 1A3 2Y2 1A4 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 1Y1 2A4 1Y2 2A3 1Y3 2Y1 GND 2A1 1Y4 2A2 The SN74F240 is available in TI’s shrink small-outline package (DB), which provides the same I/O pin count and functionality of standard small-outline packages in less than half the printed-circuit-board area. 2OE • The SN54F240 is characterized for operation over the full military temperature range of – 55°C to 125°C. The SN74F240 is characterized for operation from 0°C to 70°C. FUNCTION TABLE (each buffer) INPUTS OUTPUT Y OE A L H L L L H H X Z Copyright 1993, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 2–1 SN54F240, SN74F240 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SDFS061A – D2932, MARCH 1987 – REVISED OCTOBER 1993 logic symbol† 1OE 1A1 1A2 1A3 1A4 1 logic diagram (positive logic) 1 1OE EN 2 18 4 16 6 14 8 12 1Y1 2 18 4 16 1A1 1Y2 1Y3 1A2 14 1Y3 1A3 2OE EN 8 2A1 2A2 2A3 2A4 11 9 13 7 15 5 17 3 1Y2 1Y4 6 19 1Y1 12 1Y4 1A4 2Y1 2Y2 2Y3 19 2OE 2Y4 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 11 9 13 7 15 5 17 3 2Y1 2A1 2A2 2Y2 2Y3 2A3 2A4 2Y4 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡ Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 1.2 V to 7 V Input current range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 30 mA to 5 mA Voltage range applied to any output in the disabled or power-off state . . . . . . . . . . . . . . . . . . . – 0.5 V to 5.5 V Voltage range applied to any output in the high state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC Current into any output in the low state: SN54F240 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74F240 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Operating free-air temperature range: SN54F240 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 55°C to 125°C SN74F240 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C ‡ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: The input voltage ratings may be exceeded provided the input current ratings are observed. 2–2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54F240, SN74F240 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SDFS061A – D2932, MARCH 1987 – REVISED OCTOBER 1993 recommended operating conditions SN54F240 SN74F240 MIN NOM MAX MIN NOM MAX 4.5 5 5.5 4.5 5 5.5 UNIT VCC VIH Supply voltage VIL IIK Low-level input voltage 0.8 0.8 V Input clamp current – 18 – 18 mA IOH IOL High-level output current – 12 – 15 mA 64 mA TA Operating free-air temperature 70 °C High-level input voltage 2 2 Low-level output current V 48 – 55 125 V 0 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK VOH TEST CONDITIONS VCC = 4.5 V, VCC = 4.5 V VCC = 4.75 V, VOL VCC = 4 4.5 5V IOZH IOZL VCC = 5.5 V, VCC = 5.5 V, II IIH VCC = 5.5 V, VCC = 5.5 V, IIL IOS‡ VCC = 5.5 V, VCC = 5.5 V, ICC VCC = 5.5 V II = – 18 mA IOH = – 3 mA IOH = – 12 mA IOH = – 15 mA SN54F240 TYP† MAX MIN – 1.2 2.4 3.3 2 3.2 IOH = – 3 mA IOL = 48 mA – 1.2 2.4 3.3 2 3.1 UNIT V V 2.7 0.38 IOL = 64 mA VO = 2.7 V 0.55 0.42 VO = 0.5 V VI = 7 V VI = 2.7 V VI = 0.5 V VO = 0 Outputs high SN74F240 TYP† MAX MIN V µA 50 50 – 50 – 50 µA 0.1 0.1 mA 20 20 µA –1 mA – 225 mA –1 – 100 0.55 – 225 – 100 19 29 19 29 Outputs low 50 75 50 75 Outputs disabled 42 63 42 63 mA † All typical values are at VCC = 5 V, TA = 25°C. ‡ Not more than one output should be shorted at a time, and the duration of the short circuit should not exceed one second. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 2–3 SN54F240, SN74F240 OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS SDFS061A – D2932, MARCH 1987 – REVISED OCTOBER 1993 switching characteristics (see Note 2) PARAMETER FROM (INPUT) TO (OUTPUT) VCC = 5 V, CL = 50 pF, RL = 500 Ω, TA = 25°C VCC = 4.5 V to 5.5 V, CL = 50 pF, RL = 500 Ω, TA = MIN to MAX† ′F240 tPLH tPHL Any A Y tPZH tPZL OE Y tPHZ tPLZ OE Y SN54F240 SN74F240 MIN TYP MAX MIN MAX MIN 2.2 4.7 7 2.2 9 2.2 8 1.2 3.1 4.7 1.2 6 1.2 5.7 1.2 3.1 5.3 1.2 6.7 1.2 6.1 3.2 6.5 9 3.2 10.5 3.2 10 1.2 3.6 5.3 1.2 6.5 1.2 6.3 1.2 5.6 8 1.2 12.5 1.2 9.5 † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. NOTE 2: Load circuits and waveforms are shown in Section 1. 2–4 POST OFFICE BOX 655303 UNIT • DALLAS, TEXAS 75265 MAX ns ns ns IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated