SN75158 DUAL DIFFERENTIAL LINE DRIVER SLLS085B – JANUARY 1977 – REVISED MAY 1995 D D D D D D D D D D, P, OR PS† PACKAGE (TOP VIEW) Meets or Exceeds the Requirements of ANSI EIA/TIA-422-B and ITU Recommendation V.11 Single 5-V Supply Balanced-Line Operation TTL Compatible High Output Impedance in Power-Off Condition High-Current Active-Pullup Outputs Short-Circuit Protection Dual Channels Input Clamp Diodes 1Z 1Y 1A GND 1 8 2 7 3 6 4 5 VCC 2Z 2Y 2A † The PS package is only available left-end taped and reeled, i.e., order SN75158PSLE. description The SN75158 is a dual differential line driver designed to satisfy the requirements set by the ANSI EIA/TIA-422-B and ITU V.11 interface specifications. The outputs provide complementary signals with high-current capability for driving balanced lines, such as twisted pair, at normal line impedance without high power dissipation. The output stages are TTL totem-pole outputs providing a high-impedance state in the power-off condition. The SN75158 is characterized for operation from 0°C to 70°C. logic symbol‡ 1A 2A 3 5 logic diagram (positive logic) 2 1 6 7 1A 3 2 1 1Y 1Z 2Y 2A 2Z 5 6 7 1Y 1Z 2Y 2Z ‡ This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 1995, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN75158 DUAL DIFFERENTIAL LINE DRIVER SLLS085B – JANUARY 1977 – REVISED MAY 1995 schematics of inputs and outputs EQUIVALENT OF EACH INPUT VCC TYPICAL OF ALL OUTPUTS VCC 4 kΩ NOM 9 Ω NOM Input Output GND GND absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values, except differential output voltage VOD, are with respect to network ground terminal. VOD is at the Y output with respect to the Z output. DISSIPATION RATING TABLE PACKAGE TA ≤ 25°C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING D 725 mW 5.8 mW/°C 464 mW P 1000 mW 8.0 mW/°C 640 mW PS 450 mW 3.6 mW/°C 288 mW recommended operating conditions Supply voltage, VCC High-level input voltage, VIH MIN NOM MAX UNIT 4.75 5 5.25 V 2 Low-level input voltage, VIL High-level output current, IOH Low-level output current, IOL Operating free-air temperature, TA 2 0 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 V 0.8 V – 40 mA 40 mA 70 °C SN75158 DUAL DIFFERENTIAL LINE DRIVER SLLS085B – JANUARY 1977 – REVISED MAY 1995 electrical characteristics over operating free-air temperature range (unless otherwise noted) TEST CONDITIONS† PARAMETER VIK Input clamp voltage VCC = MIN, II = – 12 mA VOH High level output voltage High-level VCC = MIN,, VIH = 2 V, VIL = 0.8 V,, IOH = – 40 mA VOL Low level output voltage Low-level VCC = MIN,, VIH = 2 V, VIL = 0.8 V,, IOL = 40 mA VOD1| |VOD2| Differential output voltage VCC = MAX, VCC = MIN IO = 0 ∆VOD Change in magnitude of differential output voltage§ Differential output voltage VCC = MIN VCC = MAX VOC Common mode output voltage¶ Common-mode ∆VOC Change of common-mode output g in magnitude g voltage§ VCC = MIN or MAX IO Output current with power off VCC = 0 II IIH Input current at maximum input voltage VCC = MAX, VCC = MAX, IIL IOS Low-level input current ICC Supply current (both drivers) VCC = MIN High-level input current VCC = MAX, TA = 25°C, TYP‡ MAX UNIT – 0.9 – 1.5 V 24 2.4 3 V 02 0.2 3.5 2 04 0.4 V 2 × VOD2 3 V V ± 0.02 ± 0.4 1.8 3 1.5 3 0 02 ± 0.02 04 ± 0.4 RL = 100 Ω, See Figure 1 VO = 6 V VO = – 0.25 V VCC = MAX, VCC = MAX Short-circuit output current # MIN 0.1 100 – 0.1 – 100 V V V µA ± 100 VO = – 0.25 to 6 V VI = 5.5 V 1 40 µA –1 – 1.6 mA – 90 – 150 mA 37 50 mA VI = 2.4 V VI = 0.4 V – 40 mA Inputs grounded, g No load † For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions. ‡ All typical values are at VCC = 5 V and TA = 25°C except for VOC, for which VCC is as stated under test conditions. § ∆VOD and ∆|VOC| are the changes in magnitudes of VOD and VOC, respectively, that occur when the input is changed from a high level to a low level. ¶ In ANSI Standard EIA/TIA-422-B, VOC, which is the average of the two output voltages with respect to ground, is called output offset voltage, VOS. # Only one output should be shorted at a time, and duration of the short circuit should not exceed one second. switching characteristics, VCC = 5 V, TA = 25°C PARAMETER TEST CONDITIONS tPLH tPHL Propagation delay time, low-to-high-level output tPLH tPHL Propagation delay time, low-to-high-level output tTLH tTLH Transition time, low-to-high-level output Propagation delay time, high-to-low-level output Propagation delay time, high-to-low-level output See Figure 2 2, Termination A See Figure 2 2, Termination B See Figure 2 2, Termination A Transition time, high-to-low-level output Overshoot factor See Figure 2, Termination C POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MIN TYP MAX 16 25 UNIT ns 10 20 ns 13 20 ns 9 15 ns 4 20 ns 4 20 ns 10% 3 SN75158 DUAL DIFFERENTIAL LINE DRIVER SLLS085B – JANUARY 1977 – REVISED MAY 1995 PARAMETER MEASUREMENT INFORMATION 50 Ω VOD2 50 Ω VOC Figure 1. Differential and Common-Mode Output Voltages Input Pulse Generator (see Note A) Y Output Z Output Y Y CL = 15 pF (see Note B) Y CL = 30 pF (see Note B) 100 Ω 100 Ω Z CL = 15 pF (see Note B) Z TERMINATION A Z TERMINATION C TERMINATION B TEST CIRCUITS ≤ 5 ns ≤ 5 ns 90% 50% Input 3V 90% 50% 10% 10% 100% tPHL tPLH Differential Output 0V Overshoot 90% 50% 10% t TLH 90% 50% 10% 0% t THL Overshoot VOLTAGE WAVEFORMS NOTES: A. The pulse generator has the following characteristics: ZO = 50 Ω, tw = 25 ns, PRR ≤ 10 MHz. B. CL includes probe and jig capacitance. Figure 2. Test Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN75158 DUAL DIFFERENTIAL LINE DRIVER SLLS085B – JANUARY 1977 – REVISED MAY 1995 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs DATA INPUT VOLTAGE OUTPUT VOLTAGE vs DATA INPUT VOLTAGE 6 6 No Load TA = 25°C VCC = 5 V No Load 5 VCC = 5.5 V 4 VO VO – Output Voltage – V VO VO – Output Voltage – V 5 VCC = 5 V VCC = 4.5 V 3 2 1 TA = 125°C 4 3 TA = – 55°C TA = 25°C 2 1 0 0 1 2 3 0 4 0 Figure 3 Figure 4 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 0.4 5 TA = 25°C VOL – Low-Level Output Voltage – V VOL TA = 25°C VOH VOH – High-Level Output Voltage – V 4 1 2 3 VI – Data Input Voltage – V VI – Data Input Voltage – V VCC = 5.5 V 4 VCC = 5 V 3 2 VCC = 4.5 V 1 VCC = 5.5 V 0.3 VCC = 4.5 V 0.2 0.1 0 0 0 – 20 – 40 – 60 – 80 – 100 – 120 IOH – High-Level Output Current – mA 0 10 20 30 40 50 60 70 80 IOL – Low-Level Output Current – mA Figure 5 Figure 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN75158 DUAL DIFFERENTIAL LINE DRIVER SLLS085B – JANUARY 1977 – REVISED MAY 1995 TYPICAL CHARACTERISTICS OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE PROPAGATION DELAY TIMES vs FREE-AIR TEMPERATURE 4 30 VCC = 5 V VOH(IOH = – 20 mA) tpd t pd– Propagation Delay Times – ns V VO O – Output Voltage – V 3.5 3 VOH(IOH = – 40 mA) 2.5 2 1.5 1 0.5 25 VCC = 5 V See Figure 2 Termination A 20 tPLH 15 tPHL 10 5 VOL(IOL = 40 mA) 0 – 75 – 50 – 25 0 25 50 75 100 0 – 75 125 – 50 TA – Free-Air Temperature – °C – 25 Figure 7 25 50 75 100 125 Figure 8 SUPPLY CURRENT (BOTH DRIVERS) vs FREE-AIR TEMPERATURE SUPPLY CURRENT (BOTH DRIVERS) vs SUPPLY VOLTAGE 42 80 No Load TA = 25°C 40 IICC CC – Supply Current – mA 70 I ICC CC – Supply Current – mA 0 TA – Free-Air Temperature – °C 60 ÁÁÁÁÁÁ 50 Inputs Grounded 40 Inputs Open 30 20 VCC = 5 V Input Grounded Outputs Open 38 36 34 32 10 0 0 1 2 3 4 5 6 7 8 30 – 75 – 50 VCC – Supply Voltage – V Figure 9 6 – 25 0 25 Figure 10 POST OFFICE BOX 655303 50 75 TA – Free-Air Temperature – °C • DALLAS, TEXAS 75265 100 125 SN75158 DUAL DIFFERENTIAL LINE DRIVER SLLS085B – JANUARY 1977 – REVISED MAY 1995 TYPICAL CHARACTERISTICS SUPPLY CURRENT (BOTH DRIVERS) vs FREQUENCY I ICC CC – Supply Current – mA 100 VCC = 5 V RL = ∞ CL = 30 pF Inputs: 3-V Square Wave TA = 25 °C 80 60 40 20 0 0.1 0.4 1 4 10 40 100 f – Frequency – MHz Figure 11 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated PACKAGE OPTION ADDENDUM www.ti.com 4-Jun-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN75158D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75158DE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75158DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75158DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75158DRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75158DRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75158P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75158PE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75158PSLE OBSOLETE SO PS 8 SN75158PSR ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75158PSRE4 ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75158PSRG4 ACTIVE SO PS 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TBD Lead/Ball Finish Call TI MSL Peak Temp (3) Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 4-Jun-2007 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 4-Oct-2007 TAPE AND REEL BOX INFORMATION Device Package Pins Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN75158DR D 8 SITE 27 330 12 6.4 5.2 2.1 8 12 Q1 SN75158PSR PS 8 SITE 41 330 16 8.2 6.6 2.5 12 16 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com Device 4-Oct-2007 Package Pins Site Length (mm) Width (mm) Height (mm) SN75158DR D 8 SITE 27 342.9 336.6 20.64 SN75158PSR PS 8 SITE 41 346.0 346.0 33.0 Pack Materials-Page 2 MECHANICAL DATA MPDI001A – JANUARY 1995 – REVISED JUNE 1999 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE 0.400 (10,60) 0.355 (9,02) 8 5 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.020 (0,51) MIN 0.015 (0,38) Gage Plane 0.200 (5,08) MAX Seating Plane 0.010 (0,25) NOM 0.125 (3,18) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.430 (10,92) MAX 0.010 (0,25) M 4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated