SP0102BE3 “Zero Height” SiSonic™ Microphone Specification Knowles Acoustics 1151 Maplewood Drive Itasca, IL 60143 Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 1 of 10 SP0102BE3 1. DESCRIPTION AND APPLICATION 1.1 Description Zero Height Surface Mount Silicon Microphone 1.2 Application Hand held telecommunication devices 2. PART MARKING Identification Number Convention Identification Number S 1 2 4 5 6 3 S: Manufacturing Location “S” – Knowles Electronics Suzhou Suzhou, China “No Alpha Character” – Knowles Electronics Itasca Itasca, IL USA Pin 1 “E” – Engineering Samples Digits 1 – 6: Job Identification Number 3. TEMPERATURE RANGE 3.1 Operating Temperature Range: -40°C to +100°C 3.2 Storage Temperature Range: -40°C to +100°C Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 2 of 10 SP0102BE3 4. ACOUSTIC & ELECTRICAL SPECIFICATIONS Limits Symbol Directivity Condition Unit Min. Nom. Max. Omni-directional Sensitivity S @ 1kHz (0dB=1V/Pa) -46 -42 -38 dB Output impedance ZOUT @ 1kHz (0dB=1V/Pa) n/a n/a 100 Ω Current Consumption IDSS across 1.5 to 5.5 volts 0.100 n/a 0.250 mA Signal to Noise Ratio S/N @ 1kHz (0dB=1V/Pa) 55 59 n/a dB Supply Voltage Vs 1.5 n/a 5.5 V Typical Input Referred Noise ENL n/a 35 n/a dBA SPL Sensitivity Loss across Voltage Maximum Input Sound Level A-weighted Change in sensitivity over 5.5v to 1.5v No Change Across Voltage Range At 100dB SPL, THD < 1% At 115dB SPL, THD = < 10% Contact Resistance dB dB 100 Ohms 5. FREQUENCY RESPONSE CURVE Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 3 of 10 SP0102BE3 6. MECHANICAL SPECIFICATIONS Item Dim. Tol. (+/-) Units Height 1.65 +0.20 -0.10 mm Length 6.15 0.10 mm Width 3.76 0.10 mm Weight 0.09 Coplanarity < 0.1 grams mm Side View Top View Pin Output Pin # Function 1 Output 2 Ground 3 Ground 4 Power Bottom View (Note: Tolerance +/-0.15mm unless otherwise specified) Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 4 of 10 SP0102BE3 7. RECOMMENDED CUSTOMER LAND PATTERN * * Note: Minimum PCB Hole Diameter: 1.02 mm Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 5 of 10 SP0102BE3 8. RECOMMENDED SOLDER STENCIL PATTERN Notes: • The design requires that an acoustic seal be established between the SiSonic and customer PCB. This is accomplished via a solder seal. • Solder Stencil Thickness = 0.127 min to 0.178 max • Stencil Material = Stainless Steel Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 6 of 10 SP0102BE3 9. RECOMMENDED INTERFACE CIRCUIT Dotted Section Represents SiSonic Microphone R1 + Term. 4 • R2 Term. 1 • - • + Term. 3 Term. 2 External Gain (set by customer) = -R1/R2 Vref 10. PACKAGING DETAIL Pin 1 Location Model Number Suffix Reel Diameter Qty per Reel SP0102BE3 -5 7” 900 SP0102BE3 -4 13” 3,600 Tape & Reel Available in 13” and 7” diameter. Leader Length 800mm or minimum of 100 empty pockets Label Label applied to external package and direct to reel. Per JEDEC. Empty Units No consecutive empty pockets; No more than 3 empty pockets per reel. (Does not include empty pockets for leader/follower) Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 7 of 10 SP0102BE3 11. SOLDER REFLOW PROFILE Notes: 1. Maximum condition = 260 C for 30 seconds. 2. Do not pull a vacuum over the port hole of the microphone. Pulling a vacuum over the port hole can damage the device. 3. Do not board wash after the reflow process. Board washing and cleaning agents can damage the device. Do not expose to ultrasonic processing or cleaning. 4. Number of Reflow = recommend no more than 2 cycles. 12. ADDITIONAL NOTES (A) (B) (C) Packaging (reference SiSonic_Packaging_Spec.pdf) Shelf life: Twelve (12) months when devices are to be stored in factory supplied, unopened moisture sensitivity bag under environmental conditions of 30ºC, 60% R.H. Exposure: Devices should not be exposed to high humidity, high temperature environment. Customer should follow standard baking times as stated in JEDEC J-STD -033A, reference Class 2A. Out of bag: 90 days out of ESD moisture sensitive bag, assuming 30C/60% RH as maximum. Baking Condition: After 90 days, refer to JEDEC J-STD-033A for recommend baking times and temperatures, Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 8 of 10 SP0102BE3 13. RELIABILITY SPECIFICATIONS Note: After test conditions are performed, the sensitivity of the microphone shall not deviate more than 3dB from its initial value. Test Description Thermal Shock Microphone unit must operate when exposed to air-to-air thermal shock 100 cycles, from –40ºC to +125ºC. (IEC 68-2-4), High Temperature Storage Test Microphone unit must maintain sensitivity after storage at +105ºC for 1,000 hours. (IEC 68-2-2 Test Ba) Low Temperature Storage Test Microphone unit must maintain sensitivity after storage at –40ºC for 1,000 hours. (IEC 68-2-1 Test Aa) High Temperature Operating Test Microphone unit must operate within sensitivity specifications for 1,000 hours at 105ºC. (IEC 68-2-2 Test Ba) Low Temperature Operating Test Microphone unit must operate within sensitivity specifications for 1,000 hours at –40ºC. (IEC 68-2-1 Test Aa) Humidity Test Tested under Bias at 85ºC/85% R.H. for 1,000 hours. (JESD22-A101A-B) Vibration Test Microphone unit must operate under test condition: 4 cycles, from 20 to 2,000 Hz in each direction (x,y,z), 48 minutes, using peak acceleration of 20 G (+20%, -0%). (MIL 883E, method 2007.2, A) Electrostatic Discharge Tested to 8kV direct contact discharge or 15kV air discharge as specified by IEC 10004-2, level 3 and level 4. Reflow Microphone is tested to 5 passes through reflow oven, with microphone mounted upside-down under conditions of 260ºC for 30 seconds maximum. Mechanical Shock Microphone must operate after exposure to shock test of 10,000 G per IEC 68-2-27, Ea. Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 9 of 10 SP0102BE3 14. SPECIFICATION REVISIONS Revision Detailed Specification Changes Date A Initial Release 12-1-04 Knowles Acoustics, a division of Knowles Electronics, LLC. Revision: A 10 of 10