SR3.3 RailClamp Low Capacitance TVS Diode Array PROTECTION PRODUCTS Description Features RailClamps are surge rated diode arrays designed to protect high speed data interfaces. The SR series has been specifically designed to protect sensitive components which are connected to data and transmission lines from overvoltage caused by electrostatic discharge (ESD), electrical fast transients (EFT), and tertiary lightning. The unique design of the SR series devices incorporates four surge rated, low capacitance steering diodes and a TVS diode in a single package. The TVS diode is constructed using Semtech’s proprietary low voltage EPD technology for superior electrical characteristics at 3.3 volts. During transient conditions, the steering diodes direct the transient to either the positive side of the power supply line or to ground. The internal TVS diode prevents over-voltage on the power line, protecting any downstream components. The low capacitance array configuration allows the user to protect two high-speed data or transmission lines. The low inductance construction minimizes voltage overshoot during high current surges. ESD protection to IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC 61000-4-4 (EFT) 40A (5/50ns) Array of surge rated diodes with internal EPD TVS diode Protects two I/O lines Low capacitance (<10pF) for high-speed interfaces Low leakage current (< 1µA) Low operating voltage: 3.3V Solid-state technology Mechanical Characteristics JEDEC SOT-143 package Molding compound flammability rating: UL 94V-0 Marking : R3.3 Packaging : Tape and Reel Applications Circuit Diagram Data and I/O lines Sensitive Analog Inputs Video Line Protection Portable Electronics Microcontroller Input Protection WAN/LAN Equipment Schematic & PIN Configuration Pin 4 4 1 Pin 2 Pin 3 2 3 Pin 1 SOT-143 (Top View) Revision 01/16/08 1 www.semtech.com SR3.3 PROTECTION PRODUCTS Absolute Maximum Rating R ating Symbol Value Units Peak Pulse Power (tp = 8/20µs) Pp k 150 Watts Peak Pulse Current (tp = 8/20µs) IP P 10 A Peak Forward Voltage (IF = 1A, tp=8/20µs) VFP 1.5 V Lead Soldering Temperature TL 260 (10 sec.) °C Operating Temperature TJ -55 to +125 °C TSTG -55 to +150 °C Storage Temperature Electrical Characteristics SR 3.3 Parameter Reverse Stand-Off Voltage Symbol Conditions Minimum Typical VRWM Maximum Units 3.3 V Punch-Through Voltage V PT IPT = 2µA 3.5 V Snap-Back Voltage VSB ISB = 50mA 2.8 V Reverse Leakage Current IR VRWM = 3.3V, T=25°C 1 µA Clamping Voltage VC IPP = 1A, tp = 8/20µs 7 V Clamping Voltage VC IPP = 10A, tp = 8/20µs 15 V Junction Capacitance Cj Between I/O pins and Ground VR = 0V, f = 1MHz 6 10 pF Between I/O pins VR = 0V, f = 1MHz 3 2008 Semtech Corp. 2 pF www.semtech.com SR3.3 PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve 10 110 % of Rated Power or PI P Peak Pulse Power - PPk (kW) 100 1 0.1 90 80 70 60 50 40 30 20 10 0 0.01 0.1 1 10 100 0 1000 25 Pulse Waveform Percent of IPP 80 -t 50 40 td = IPP/2 30 20 10 0 5 10 15 150 12 10 Line-To-Ground 8 6 4 Waveform Parameters: tr = 8µs td = 20µs 2 0 125 Line-To-Line 14 Clamping Voltage - VC (V) 90 e 100 16 Waveform Parameters: tr = 8µs td = 20µs 100 60 75 Clamping Voltage vs. Peak Pulse Current 110 70 50 Ambient Temperature - TA (oC) Pulse Duration - tp (µs) 20 25 30 0 Time (µs) 0 2 4 6 8 10 12 Peak Pulse Current - IPP (A) Forward Voltage vs. Forward Current 10 Forward Voltage - VF (V) 9 8 7 6 5 4 3 Waveform Parameters: tr = 8µs td = 20µs 2 1 0 0 5 10 15 20 25 30 35 40 45 50 Forward Current - IF (A) 2008 Semtech Corp. 3 www.semtech.com SR3.3 PROTECTION PRODUCTS Applications Information Device Connection Options for Protection of Tw o High-Speed Data Lines Data Line Pr o t ection Using Int ernal T V S Diode Pro Internal as Reference The SR3.3 TVS is designed to protect two data lines from transient over-voltages by clamping them to a fixed reference. When the voltage on the protected line exceeds the reference voltage (plus diode VF) the steering diodes are forward biased, conducting the transient current away from the sensitive circuitry. Data lines are connected at pins 2 and 3. The negative reference (REF1) is connected at pin 1. This pin should be connected directly to a ground plane on the board for best results. The path length is kept as short as possible to minimize parasitic inductance. The positive reference (REF2) is connected at pin 4. The options for connecting the positive reference are as follows: Note that pins 4 is connected internally to the cathode of the low voltage TVS. It is not recommended that this pin be directly connected to a DC source greater than the snap-back votlage (VSB) as the device can latch on as described below. IPP ISB EPD TVS Characteristics These devices are constructed using Semtech’s proprietary EPD technology. By utilizing the EPD technology, the SR3.3 can effectively operate at 3.3V while maintaining excellent electrical characteristics. IPT VBRR IR VRWM VSB VPT VC IBRR The EPD TVS employs a complex nppn structure in contrast to the pn structure normally found in traditional silicon-avalanche TVS diodes. Since the EPD TVS devices use a 4-layer structure, they exhibit a slightly different IV characteristic curve when compared to conventional devices. During normal operation, the device represents a high-impedance to the circuit up to the device working voltage (VRWM). During an ESD event, the device will begin to conduct and will enter a low impedance state when the punch through voltage (VPT) is exceeded. Unlike a conventional device, the low voltage TVS will exhibit a slight negative resistance characteristic as it conducts current. This characteristic aids in lowering the clamping voltage of the device, but must be considered in applications where DC voltages are present. Figure 1 - EPD TVS IV Characteristic Curve characteristics due to its structure. This point is defined on the curve by the snap-back voltage (VSB) and snap-back current (ISB). To return to a nonconducting state, the current through the device must fall below the ISB (approximately <50mA) and the voltage must fall below the VSB (normally 2.8 volts for a 3.3V device). If a 3.3V TVS is connected to 3.3V DC source, it will never fall below the snap-back voltage of When the TVS is conducting current, it will exhibit a slight “snap-back” or negative resistance 2008 Semtech Corp. 2.8V and will therefore stay in a conducting state. 4 www.semtech.com SR3.3 PROTECTION PRODUCTS Applications Information (continued) Board Layout Considerations for ESD Protection Board layout plays an important role in the suppression of extremely fast rise-time ESD transients. Recall that the voltage developed across an inductive load is proportional to the time rate of change of current PIN Descriptions through the load (V = L di/dt). The total clamping voltage seen by the protected load will be the sum of the TVS clamping voltage and the voltage due to the parasitic inductance (VC(TOT) = VC + L di/dt) . Parasitic inductance in the protection path can result in significant voltage overshoot, reducing the effectiveness of the suppression circuit. An ESD induced transient for example reaches a peak in approximately 1ns. For a 30A pulse (per IEC 61000-4-2 Level 4), 1nH of series inductance will increase the effective clamping voltage by 30V (V = 1x10-9 (30/1x10-9)). For maximum effectiveness, the following board layout guidelines are recommended: z z z Minimize the path length between the SR3.3 and the protected line. Place the SR3.3 near the RJ45 connector to restrict transient coupling in nearby traces. Minimize the path length (inductance) between the RJ45 connector and the SR3.3. Matte Tin Lead Finish Matte tin has become the industry standard lead-free replacement for SnPb lead finishes. A matte tin finish is composed of 100% tin solder with large grains. Since the solder volume on the leads is small compared to the solder paste volume that is placed on the land pattern of the PCB, the reflow profile will be determined by the requirements of the solder paste. Therefore, these devices are compatible with both lead-free and SnPb assembly techniques. In addition, unlike other lead-free compositions, matte tin does not have any added alloys that can cause degradation of the solder joint. 2008 Semtech Corp. 5 www.semtech.com SR3.3 PROTECTION PRODUCTS Outline Drawing - SOT-143 D A e H e/2 DIM 4 3 GAUGE PLANE SEATING PLANE B C 1 A A1 A2 b b1 c D E E1 e e1 L L1 N 0 aaa bbb ccc 0.25 L L1 E E1 c 0 DETAIL A 2 bxN e1 bbb A2 C A B SEE DETAIL A SIDE VIEW A 4X DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .035 - .048 0.80 1.22 .006 0.013 0.15 .042 0.75 0.90 1.07 .020 0.30 0.51 .037 0.76 0.94 .008 0.08 0.20 .114 .120 2.80 2.90 3.04 .093 .104 2.10 2.37 2.64 .051 .055 1.20 1.30 1.40 .075 1.92 BSC .008 0.20 BSC .015 .020 .024 0.40 0.50 0.60 (.021) (0.54) 4 4 0° 8° 0° 8° .006 0.15 .008 0.20 .004 0.10 .031 .000 .029 .011 .029 .003 .110 .082 .047 ccc C SEATING PLANE A1 b1 aaa C C A B NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H- 3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. 4. REFERENCE JEDEC STD TO-253, VARIATION D. Land Pattern - SOT-143 X1 X1 Y DIM Z C E1 G E2 Y X2 C E1 E2 G X1 X2 Y Z DIMENSIONS INCHES MILLIMETERS (.087) .076 .068 .031 .039 .047 .055 .141 (2.20) 1.92 1.72 0.80 1.00 1.20 1.40 3.60 X1 NOTES: 1. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 2. REFERENCE IPC-SM-782A. 2008 Semtech Corp. 6 www.semtech.com SR3.3 PROTECTION PRODUCTS Marking Codes Part Number Marking Code SR3.3 R3.3 Ordering Information Par t Number Lead Finish Qty per Reel R eel Size SR3.3.TC SnPb 3,000 7 Inch SR3.3.TCT Pb Free 3,000 7 Inch Contact Information Semtech Corporation Protection Products Division 200 Flynn Road, Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 2008 Semtech Corp. 7 www.semtech.com