BB SRC4190IDBR

SRC4190(1)
SRC
419
0
SBFS023A – JUNE – REVISED JULY 2003
192kHz Stereo Asynchronous
Sample Rate Converters
FEATURES
APPLICATIONS
● AUTOMATIC SENSING OF THE INPUT-TOOUTPUT SAMPLING RATIO
● WIDE INPUT-TO-OUTPUT SAMPLING RANGE:
16:1 to 1:16
● SUPPORTS INPUT AND OUTPUT SAMPLING
RATES UP TO 212kHz
● DYNAMIC RANGE: 128dB (–60dbFS input,
BW = 20Hz to fS /2, A-Weighted)
● THD+N: –125dB (0dbFS input, BW = 20Hz to
fS /2)
● ATTENUATES SAMPLING AND REFERENCE
CLOCK JITTER
● HIGH PERFORMANCE, LINEAR PHASE
DIGITAL FILTERING
● FLEXIBLE AUDIO SERIAL PORTS:
Master or Slave Mode Operation
Supports I2S, Left Justified, Right Justified, and
TDM Data Formats
Supports 16, 18, 20, or 24-Bit Audio Data
TDM Mode allows daisy chaining of up to eight
devices
● SUPPORTS 24-, 20-, 18-, or 16-BIT INPUT AND
OUTPUT DATA
All output data is dithered from the internal
28-Bit data path
● LOW GROUP DELAY OPTION FOR
INTERPOLATION FILTER
● SOFT MUTE FUNCTION
● BYPASS MODE
● POWER DOWN MODE
● OPERATES FROM A SINGLE +3.3 VOLT
POWER SUPPLY
● SMALL SSOP-28 PACKAGE
● PIN COMPATIBLE WITH THE SRC4192,
AD1895, AND AD1896(2)
●
●
●
●
●
●
DIGITAL MIXING CONSOLES
DIGITAL AUDIO WORKSTATIONS
AUDIO DISTRIBUTION SYSTEMS
BROADCAST STUDIO EQUIPMENT
HIGH-END A/V RECEIVERS
GENERAL DIGITAL AUDIO PROCESSING
DESCRIPTION
The SRC4190 is an asynchronous sample rate converter
designed for professional and broadcast audio applications.
The SRC4190 combines a wide input-to-output sampling
ratio with outstanding dynamic range and low distortion.
Input and output serial ports support standard audio formats,
as well as a Time Division Multiplexed (TDM) mode. Flexible
audio interfaces allow the SRC4190 to connect to a wide
range of audio data converters, digital audio receivers and
transmitters, and digital signal processors.
The SRC4190 is a standalone pin-programmed device, with
control pins for mode, data format, mute, bypass, and low
group delay functions.
The SRC4190 may be operated from a single +3.3V power
supply. A separate digital I/O supply (VIO) operates over the
+1.65V to +3.6V supply range, allowing greater flexibility
when interfacing to current and future generation signal
processors and logic devices. The SRC4190 is available in
a SSOP-28 package.
(1) Patents Pending.
(2) Refer to the Applications Information section of this data sheet for details.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
Copyright © 2003, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ABSOLUTE MAXIMUM RATINGS(1)
ELECTROSTATIC
DISCHARGE SENSITIVITY
Supply Voltage, VDD .......................................................... –0.3V to +4.0V
Supply Voltage, VIO ........................................................... –0.3V to +4.0V
Digital Input Voltage .......................................................... –0.3V to +4.0V
Operating Temperature Range ........................................ –45°C to +85°C
Storage Temperature Range ......................................... –65°C to +150°C
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
NOTE: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is
not implied.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may be
more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
PRODUCT
SRC4190
"
PACKAGE-LEAD
PACKAGE
DESIGNATOR(1)
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
SSOP-28
DB
–45°C to +85°C
SRC4190I
"
"
"
"
SRC4190IDB
SRC4190IDBR
Rails, 50
Tape and Reel, 2000
NOTE: (1) For the most current specifications and package information, refer to our web site at www.ti.com.
PIN CONFIGURATION (SRC4190)
PIN DESCRIPTIONS (SRC4190)
Top View
LGRP
2
RCKI
2
27 MODE1
N.C.
3
26 MODE0
SDIN
4
25 BCKO
BCKI
5
24 LRCKO
LRCKI
6
23 SDOUT
7
DGND
8
NAME
DESCRIPTION
1
LGRP
Low Group Delay Control Input (Active High)
2
RCKI
Reference Clock Input
3
N.C.
No Connection
4
SDIN
Audio Serial Data Input
5
BCKI
Input Port Bit Clock I/O
6
LRCKI
7
VIO
28 MODE2
1
VIO
PIN#
SRC4190
Input Port Left/Right Word Clock I/O
Digital I/O Supply, +1.65V to VDD
8
DGND
Digital Ground
9
BYPAS
ASRC Bypass Control Input (Active High)
10
IFMT0
Input Port Data Format Control Input
11
IFMT1
Input Port Data Format Control Input
12
IFMT2
22 VDD
13
RST
21 DGND
14
MUTE
15
RDY
Input Port Data Format Control Input
Reset Input (Active Low)
Output Mute Control Input (Active High)
ASRC Ready Status Output (Active Low)
BYPAS
9
20 TDMI
16
OWL1
Output Port Data Word Length Control Input
IFMT0
10
19 OFMT0
17
OWL0
Output Port Data Word Length Control Input
18
OFMT1
Output Port Data Format Control Input
IFMT1
11
18 OFMT1
19
OFMT0
IFMT2
12
17 OWL0
20
TDMI
TDM Data Input (Connect to DGND when not in use)
RST
16 OWL1
21
DGND
Digital Ground
13
22
VDD
MUTE
14
15 RDY
23
SDOUT
24
LRCKO
Output Port Left/Right Word Clock I/O
25
BCKO
Output Port Bit Clock I/O
26
MODE0
Serial Port Mode Control Input
27
MODE1
Serial Port Mode Control Input
28
MODE2
Serial Port Mode Control Input
Output Port Data Format Control Input
Digital Core Supply, +3.3V
Audio Serial Data Output
SRC4190
www.ti.com
SBFS023A
ELECTRICAL CHARACTERISTICS
All parameters specified with TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
SRC4190
PARAMETER
DYNAMIC PERFORMANCE(1)
Resolution
Input Sampling Frequency
Output Sampling Frequency
Input: Output Sampling Ratio
Upsampling
Downsampling
Dynamic Range
CONDITION
TYP
MAX
UNITS
212
212
Bits
kHz
kHz
24
fSIN
4
4
fSOUT
1:16
16:1
BW = 20Hz to fSOUT /2, –60dBFS Input
fIN = 1kHz, Unweighted
(add 3dB to spec for A-weighted result)
44.1kHz:48kHz
48kHz:44.1kHz
48kHz:96kHz
44.1kHz:192kHz
96kHz:48kHz
192kHz:12kHz
192kHz:32kHz
192kHz:48kHz
32kHz:48kHz
12kHz:192kHz
Total Harmonic Distortion + Noise
125
125
125
125
125
125
125
125
125
125
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
–125
–125
–125
–125
–125
–125
–125
–125
–125
–125
0
0
–128
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
Degrees
dB
BW = 20Hz to fSOUT /2, 0dBFS Input
fIN = 1kHz, Unweighted
44.1kHz:48kHz
48kHz:44.1kHz
48kHz:96kHz
44.1kHz:192kHz
96kHz:48kHz
192kHz:12kHz
192kHz:32kHz
192kHz:48kHz
32kHz:48kHz
12kHz:192kHz
Interchannel Gain Mismatch
Interchannel Phase Deviation
Mute Attenuation
24-Bit Word Length, A-weighted
DIGITAL INTERPOLATION FILTER
CHARACTERISTICS
Passband
Passband Ripple
Transition Band
Stop Band
Stop Band Attenuation
Normal Group Delay (LGRP = 0)
Low Group Delay (LGRP = 1)
0.4535 x fSIN
0.5465 x fSIN
–125
0.4535 x fSIN
±0.007
0.5465 x fSIN
Hz
dB
Hz
Hz
dB
Seconds
Seconds
0.4535 x fSOUT
±0.008
0.5465 x fSOUT
Hz
dB
Hz
Hz
dB
Seconds
VIO
0.3 x VIO
10
10
VIO
0.2 x VIO
V
V
µA
µA
V
V
pF
102.53125/fSIN
70.53125/fSIN
DIGITAL DECIMATION FILTER
CHARACTERISTICS
Passband
Passband Ripple
Transition Band
Stop Band
Stop Band Attenuation
Group Delay
DIGITAL I/O CHARACTERISTICS
High-Level Input Voltage
Low Level Input Voltage
High-Level Input Current
Low-Level Input Current
High-Level Output Voltage
Low-Level Output Voltage
Input Capacitance
MIN
0.4535 x fSOUT
0.5465 x fSOUT
–125
36.46875/fSOUT
VIH
VIL
IIH
IIL
VOH
VOL
CIN
0.7 x VIO
0
0.5
0.5
IO = –4mA
IO = +4mA
0.8 x VIO
0
3
NOTES: (1) Dynamic performance measured with an Audio Precision System Two Cascade or Cascade Plus.
(2) fSMIN = min (fSIN, fSOUT).
(3) fSMAX = max (fSIN, fSOUT).
SRC4190
SBFS023A
www.ti.com
3
ELECTRICAL CHARACTERISTICS (Cont.)
All parameters specified with TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
SRC4190
PARAMETER
SWITCHING CHARACTERISTICS
Reference Clock Timing
RCKI Frequency(2), (3)
RCKI Period
RCKI Pulsewidth High
RCKI Pulsewidth Low
Reset Timing
RST Pulse Width Low
Input Serial Port Timing
LRCKI to BCKI Setup Time
BCKI Pulsewidth High
BCKI Pulsewidth Low
SDIN Data Setup Time
SDIN Data Hold Time
Output Serial Port Timing
SDOUT Data Delay Time
SDOUT Data Hold Time
BCKO Pulsewidth High
BCKO Pulsewidth Low
TDM Mode Timing
LRCKO Setup Time
LRCKO Hold Time
TDMI Data Setup Time
TDMI Data Hold Time
POWER SUPPLIES
Operating Voltage
VDD
VIO
Supply Current
IDD, Power Down
IDD, Dynamic
IIO, Power Down
IIO, Dynamic
Total Power Dissipation
PD, Power Down
PD, Dynamic
CONDITION
MIN
TYP
MAX
UNITS
50
1/(128 x fSMIN)
MHz
ns
ns
ns
tRCKIP
tRCKIH
tRCKIL
128 x fSMIN
20
0.4 x tRCKIP
0.4 x tRCKIP
tRSTL
500
ns
tLRIS
tSIH
tSIL
tLDIS
tLDIH
10
10
10
10
10
ns
ns
ns
ns
ns
tDOPD
tDOH
tSOH
tSOL
2
10
5
ns
ns
ns
ns
tLROS
tLROH
tTDMS
tTDMH
10
10
10
10
ns
ns
ns
ns
10
3.0
1.65
VDD = +3.3V, VIO = +3.3V
RST = 0, No Clocks
fSIN = fsOUT = 192kHz
RST = 0, No Clocks
fSIN = fSOUT = 192kHz
VDD = +3.3V, VIO = +3.3V
RST = 0, No Clocks
fSIN = fSOUT = 192kHz
+3.3
+3.3
3.6
3.6
V
V
100
µA
mA
µA
mA
66
100
2
660
225
µW
mW
NOTES: (1) Dynamic performance measured with an Audio Precision System Two Cascade or Cascade Plus.
(2) fSMIN = min (fSIN, fSOUT).
(3) fSMAX = max (fSIN, fSOUT).
4
SRC4190
www.ti.com
SBFS023A
TYPICAL CHARACTERISTICS
At TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
FFT with 1kHz INPUT TONE at –60dBFS
(12kHz:192kHz)
FFT with 1kHz INPUT TONE at 0dBFS
(12kHz:192kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
20k
40k
60k
80k
0
96k
40k
60k
80k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(32kHz:48kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(32kHz:48kHz)
0
–60
–20
–70
96k
–80
–40
–90
–60
–100
dBFS
dBFS
20k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k
24k
0
10k
15k
20k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(44.1kHz:48kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(44.1kHz:48kHz)
0
–60
–20
–70
24k
–80
–40
–90
–60
–100
dBFS
dBFS
5k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k
24k
5k
10k
15k
20k
24k
Frequency (Hz)
Frequency (Hz)
SRC4190
SBFS023A
0
www.ti.com
5
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
FFT with 1kHz INPUT TONE at 0dBFS
(44.1kHz:96kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(44.1kHz:96kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
10k
20k
30k
40k
48k
0
20k
30k
40k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(44.1kHz:192kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(44.1kHz:192kHz)
0
–60
–20
–70
48k
–80
–40
–90
–60
–100
dBFS
dBFS
10k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
20k
40k
60k
80k
96k
0
20k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(48kHz:44.1kHz)
60k
80k
96k
FFT with 1kHz INPUT TONE at –60dBFS
(48kHz:44.1kHz)
0
–60
–20
–70
–80
–40
–90
–60
–100
dBFS
dBFS
40k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k 22k
Frequency (Hz)
6
0
5k
10k
15k
20k 22k
Frequency (Hz)
SRC4190
www.ti.com
SBFS023A
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
FFT with 1kHz INPUT TONE at –60dBFS
(48kHz:96kHz)
FFT with 1kHz INPUT TONE at 0dBFS
(48kHz:96kHz)
–60
0
–70
–20
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
10k
20k
30k
40k
0
48k
10k
20k
30k
40k
Frequency (Hz)
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(48kHz:192kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(48kHz:192kHz)
0
–60
–20
–70
48k
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
20k
40k
60k
80k
96k
0
20k
Frequency (Hz)
40k
60k
80k
96k
Frequency (Hz)
FFT with 1kHz INPUT TONE at –60dBFS
(96kHz:44.1kHz)
FFT with 1kHz INPUT TONE at 0dBFS
(96kHz:44.1kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k 22k
SRC4190
SBFS023A
0
5k
10k
15k
20k 22k
Frequency (Hz)
Frequency (Hz)
www.ti.com
7
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
FFT with 1kHz INPUT TONE at –60dBFS
(96kHz:48kHz)
FFT with 1kHz INPUT TONE at 0dBFS
(96kHz:48kHz)
–60
0
–70
–20
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k
0
24k
5k
10k
15k
20k
Frequency (Hz)
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(96kHz:192kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(96kHz:192kHz)
0
–60
–20
–70
24k
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
20k
40k
60k
80k
0
96k
20k
40k
60k
80k
96k
Frequency (Hz)
Frequency (Hz)
FFT with 1kHz INPUT TONE at –60dBFS
(192kHz:12kHz)
FFT with 1kHz INPUT TONE at 0dBFS
(192kHz:12kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
1k
2k
3k
4k
5k
0
6k
8
1k
2k
3k
4k
5k
6k
Frequency (Hz)
Frequency (Hz)
SRC4190
www.ti.com
SBFS023A
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
FFT with 1kHz INPUT TONE at 0dBFS
(192kHz:32kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(192kHz:12kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
2.5k
5k
7.5k
10k
12.5k
15k 16k
0
2.5k
5k
7.5k
10k
12.5k
Frequency (Hz)
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(192kHz:44.1kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(192kHz:44.1kHz)
0
–60
–20
–70
15k 16k
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
0
20k 22k
5k
10k
15k
20k 22k
Frequency (Hz)
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(192kHz:48kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(192kHz:48kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k
24k
Frequency (Hz)
5k
10k
15k
20k
24k
Frequency (Hz)
SRC4190
SBFS023A
0
www.ti.com
9
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
FFT with 1kHz INPUT TONE at –60dBFS
(192kHz:96kHz)
FFT with 1kHz INPUT TONE at 0dBFS
(192kHz:96kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
10k
20k
30k
40k
0
48k
10k
0
0
–20
–20
–40
–40
–60
–60
–80
–100
–140
–140
–160
–160
15k
48k
–100
–120
10k
40k
–80
–120
5k
30k
FFT with 20kHz INPUT TONE at 0dBFS
(48kHz:44.1kHz)
dBFS
dBFS
FFT with 20kHz INPUT TONE at 0dBFS
(44.1kHz:48kHz)
0
20k
Frequency (Hz)
Frequency (Hz)
20k
24k
0
5k
10k
15k
20k 22k
Frequency (Hz)
Frequency (Hz)
FFT with 20kHz INPUT TONE at 0dBFS
(48kHz:96kHz)
FFT with 20kHz INPUT TONE at 0dBFS
(96kHz:48kHz)
–20
–40
–40
–60
–60
dBFS
dBFS
0
–20
–80
–100
–100
–120
–120
–140
–140
–160
–160
0
10k
20k
30k
40k
48k
0
5k
10k
15k
20k
24k
Frequency (Hz)
Frequency (Hz)
10
–80
SRC4190
www.ti.com
SBFS023A
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
FFT with 80kHz INPUT TONE at 0dBFS
(192kHz:192kHz)
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(44.1kHz:48kHz)
0
Total Harmonic Distortion+Noise (dB)
–100
–20
–40
dBFS
–60
–80
–100
–120
–140
–160
0
20k
40k
60k
80k
–135
–140
–145
–120
–100
–80
–60
–40
–20
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(48kHz:96kHz)
0
–100
Total Harmonic Distortion+Noise (dB)
Total Harmonic Distortion+Noise (dB)
–130
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(48kHz:44.1kHz)
–115
–120
–125
–130
–135
–140
–145
–120
–100
–80
–60
–40
–20
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–140
0
–120
–100
–80
–60
–40
–20
Input Amplitude (dBFS)
Input Amplitude (dBFS)
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(96kHz:48kHz)
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(44.1kHz:192kHz)
0
–100
Total Harmonic Distortion+Noise (dB)
–100
Total Harmonic Distortion+Noise (dB)
–125
Input Amplitude (dBFS)
–110
–105
–110
–115
–120
–125
–130
–135
–140
–145
–120
–100
–80
–60
–40
–20
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–140
0
–120
–100
–80
–60
–40
–20
0
Input Amplitude (dBFS)
Input Amplitude (dBFS)
SRC4190
SBFS023A
–115
–120
Frequency (Hz)
–105
–150
–140
–110
–150
–140
96k
–100
–150
–140
–105
www.ti.com
11
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(192kHz:44.1kHz)
THD+N vs INPUT FREQUENCY WITH 0dBFS INPUT
(44.1kHz:48kHz)
–100
Total Harmonic Distortion+Noise (dB)
Total Harmonic Distortion+Noise (dB)
–100
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–140
–100
–80
–60
–40
–20
–125
–130
–135
–140
–145
0
5k
10k
15k
20k
Input Amplitude (dBFS)
Input Frequency (Hz)
THD+N vs INPUT FREQUENCY WITH 0dBFS INPUT = 1kHz
(48kHz:44.1kHz)
THD+N vs INPUT FREQUENCY WITH 0dBFS
(48kHz:96kHz)
–100
Total Harmonic Distortion+Noise (dB)
Total Harmonic Distortion+Noise (dB)
–115
–120
0
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
0
5k
10k
15k
20k
0
5k
10k
15k
20k
Input Frequency (Hz)
Input Frequency (Hz)
THD+N vs INPUT FREQUENCY WITH 0dBFS
(96kHz:48kHz)
THD+N vs INPUT FREQUENCY WITH 0dBFS
(44.1kHz:192kHz)
–100
Total Harmonic Distortion+Noise (dB)
–100
Total Harmonic Distortion+Noise (dB)
–110
–150
–120
–100
–105
–110
–115
–120
–125
–130
–135
–140
–145
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–150
0
5k
10k
15k
0
20k
5k
10k
15k
20k
Input Frequency (Hz)
Input Frequency (Hz)
12
–105
SRC4190
www.ti.com
SBFS023A
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
LINEARITY with fIN = 200Hz
(44.1kHz:48kHz)
THD+N vs INPUT FREQUENCY WITH 0dBFS
(192kHz:44.1kHz)
–105
–110
Output Amplitude (dBFS)
Total Harmonic Distortion+Noise (dB)
–100
–115
–120
–125
–130
–135
–140
–145
–150
5k
10k
15k
Input Amplitude (dBFS)
LINEARITY with fIN = 200Hz
(48kHz:44.1kHz)
LINEARITY with fIN = 200Hz
(48kHz:96kHz)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
0
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
Input Amplitude (dBFS)
LINEARITY with fIN = 200Hz
(96kHz:48kHz)
LINEARITY with fIN = 200Hz
(44.1kHz:192kHz)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
0
0
Input Amplitude (dBFS)
SRC4190
SBFS023A
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
Input Amplitude (dBFS)
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
Input Amplitude (dBFS)
Output Amplitude (dBFS)
Output Amplitude (dBFS)
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
20k
Input Frequency (Hz)
Output Amplitude (dBFS)
Output Amplitude (dBFS)
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
www.ti.com
13
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, VDD = +3.3V, and VIO = +3.3V, unless otherwise noted.
FREQUENCY RESPONSE with 0dBFS INPUT
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
dBFS
Output Amplitude (dBFS)
LINEARITY with fIN = 200Hz
(192kHz:44.1kHz)
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
0
192kHz:48kHz
192kHz:32kHz
192kHz:96kHz
0
10k
20k
Input Amplitude (dBFS)
0
–0.01
–0.02
–0.03
–0.04
–0.05
–0.06
–0.07
–0.08
–0.09
–0.10
–0.11
–0.12
–0.13
–0.14
–0.15
5k
10k
15k
20k 22k
50k
60k
0
–0.01
–0.02
–0.03
–0.04
–0.05
–0.06
–0.07
–0.08
–0.09
–0.10
–0.11
–0.12
–0.13
–0.14
–0.15
0
Input Frequency (Hz)
14
40k
PASS BAND RIPPLE
(192k:48k)
(dBFS)
(dBFS)
PASS BAND RIPPLE
(48k:48k)
0
30k
Frequency (Hz)
5k
10k
15k
20k 22k
Input Frequency (Hz)
SRC4190
www.ti.com
SBFS023A
PRODUCT OVERVIEW
passing through encoded or compressed audio data, or nonaudio control or status data.
The SRC4190 is an asynchronous sample rate converter
(ASRC) designed for professional audio applications. Operation at input and output sampling frequencies up to 212kHz
is supported, with an input/output sampling ratio range of
16:1 to 1:16. Excellent dynamic range and Total Harmonic
Distortion + Noise (THD+N) are achieved by employing high
performance and linear phase digital filtering. Digital filtering
options allow for lower group delay processing.
A soft mute function is available providing artifact-free operation while muting the audio output signal. The mute attenuation is typically –128dB.
FUNCTIONAL BLOCK DIAGRAM
Figure 1 shows a functional block diagram of the SRC4190.
Audio data is received at the input port, clocked by either the
audio data source in Slave mode or by the SRC4190 in
Master mode. The output port data is clocked by either the
audio data source in Slave mode, or by the SRC4190 in
Master mode. The input data is passed through interpolation
filters which up-sample the data, which is then passed on to
the re-sampler. The rate estimator compares the input and
output sampling frequencies by comparing LRCKI, LRCKO,
and a reference clock. The results include an offset for the
FIFO pointer and the coefficients needed for re-sampling
function.
The audio input and output ports support standard audio data
formats, as well as a TDM interface mode. Word lengths of
24-, 20-, 18-, and 16-bits are supported. Both ports may
operate in Slave mode, deriving their word and bit clocks
from external input and output devices. Alternatively, one
port may operate in Master mode while the other remains in
Slave mode. In Master mode, the LRCK and BCK clocks are
derived from the reference clock input, RCKI. The flexible
configuration of the input and output ports allows connection
to a wide variety of audio data converters, interface devices,
digital signal processors, and programmable logic.
The output of the re-sampler is then passed on to the
decimation filter. The decimation filter performs down-sampling and anti-alias filtering functions.
A bypass mode is included, which allows audio data to be
passed directly from the input port to the output port, bypassing the ASRC function. The bypass option is useful for
LRCKI
BCKI
SDIN
Audio
Input
Port
fSIN
Interpolation
Filters
16fSIN
Re-Sampler
16fSOUT
MODE [2:0]
IFMT [2:0]
REFCLK
OFMT [1:0]
OWL [1:0]
MUTE
LRCKI
Control
Logic
Rate
Estimator
BYPAS
LGRP
RST
LRCKO
RDY
fSOUT
Decimation
Filters
LRCKO
BCKO
SDOUT
Audio
Output
Port
TDMI
VDD
DGND
RCKI
Reference
Clock
Power
REFCLK
VIO
DGND
FIGURE 1. SRC4190 Functional Block Diagram.
SRC4190
SBFS023A
www.ti.com
15
REFERENCE CLOCK
AUDIO PORT MODES
The SRC4190 requires a reference clock for operation. The
reference clock is applied at the RCKI input, pin 2. Figure 2
illustrates the reference clock connections and requirements
for the SRC4190. The reference clock may operate at 128fS,
256fS, or 512fS, where fS is the input or output sampling
frequency. The maximum external reference clock input
frequency is 50 MHz.
The SRC4190 supports seven serial port modes, which are
shown in Table 1. The audio port mode is selected using the
MODE0 (pin 26), MODE1 (pin 27), and MODE2 (pin 28)
inputs.
In Slave mode, the port LRCK and BCK clocks are configured as inputs, and receive their clocks from an external
audio device. In Master mode, the LRCK and BCK clocks are
configured as outputs, being derived from the reference
clock input (RCKI). Only one port can be set to Master mode
at any given time, as indicated in Table 1.
SRC4190
MODE2 MODE1 MODE0
RCKI
2
From External
Clock Source
50MHz max
tRCKIP
RCKI
tRCKIH
tRCKIL
tRCKIP > 20ns min
tRCKIH > 0.4 tRCKIP
tRCKIL > 0.4 tRCKIP
SERIAL PORT MODE
0
0
0
Both Input and Output Ports are Slave mode
0
0
1
Output Port is Master mode with RCKI = 128f S
0
1
0
Output Port is Master mode with RCKI = 512f S
0
1
1
Output Port is Master mode with RCKI = 256f S
1
0
0
Both Input and Output Ports are Slave Mode
1
0
1
Input Port is Master mode with RCKI = 128f S
1
1
0
Input Port is Master mode with RCKI = 512f S
1
1
1
Input Port is Master mode with RCKI = 256f S
TABLE 1. Setting the Serial Port Modes.
INPUT PORT OPERATION
FIGURE 2. Reference Clock Input Connections and Timing
Requirements.
RESET AND POWER DOWN OPERATION
The SRC4190 may be reset using the RST input (pin 13).
There is no internal power on reset, so the user should force
a reset sequence after power up in order to initialize the
device. In order to force a reset, the reference clock input
must be active, with an external clock source supplying a
valid reference clock signal (refer to Figure 2). The user must
assert RST low for a minimum of 500 nanoseconds and then
bring RST high again to force a reset. Figure 3 shows the
reset timing for the SRC4190.
The SRC4190 also supports a power-down mode. Powerdown mode may be set by holding the RST input low.
The audio input port is a three-wire synchronous serial
interface that may operate in either Slave or Master mode.
The SDIN input (pin 4) is the serial audio data input. Audio
data is input at this pin in one of three standard audio data
formats: Philips I2S, Left Justified, or Right Justified. The
audio data word length may be up to 24 bits for I2S and Left
Justified formats, while the Right Justified format supports
16-, 18-, 20-, or 24-bit data. The data formats are shown in
Figure 4, while critical timing parameters are shown in Figure
5 and listed in the Electrical Characteristics table.
The bit clock is either an input or output at BCKI (pin 5). In
slave mode, BCKI is configured as an input pin, and may
operate at rates from 32fS to 128fS, with a minimum of one
clock cycle per data bit. In Master mode, BCKI operates at a
fixed rate of 64fS.
RCKI
RST
tRSTL > 500ns
FIGURE 3. Reset Pulse Width Requirement.
16
SRC4190
www.ti.com
SBFS023A
Left Channel
Right Channel
LRCKO
BCKI
SDIN
MSB
LSB
MSB
LSB
(a) Left Justified Data Format
LRCKI
BCKI
MSB
SDIN
LSB
MSB
LSB
(b) Right Justified Data Format
LRCKI
BCKI
SDIN
MSB
LSB
MSB
LSB
(c) I2S Data Format
1/fS
FIGURE 4. Input Data Formats.
case, the clock rate is equal to fS, the input sampling
frequency. The LRCKI duty cycle is fixed to 50% for Master
mode operation.
LRCKI
tLRIS
Table 2 illustrates data format selection for the input port.
The IFMT0 (pin 10), IFMT1 (pin 11), and IFMT2 (pin 12)
inputs are utilized to set the input port data format.
tSIH
BCKI
tLDIS
tSIL
IFMT2
IFMT1
IFMT0
INPUT PORT DATA FORMAT
0
0
0
24-Bit Left Justified
0
0
1
24-Bit I2S
0
1
0
Unused
0
1
1
Unused
FIGURE 5. Input Port Timing.
1
1
0
0
0
1
16-Bit Right Justified
18-Bit Right Justified
The left/right word clock, LRCKI (pin 6), may be configured
as an input or output pin. In Slave mode, LRCKI is an input
pin, while in Master mode LRCKI is an output pin. In either
1
1
0
20-Bit Right Justified
1
1
1
24-Bit Right Justified
SDIN
tLDIH
TABLE 2. Input Port Data Format Selection.
SRC4190
SBFS023A
www.ti.com
17
OUTPUT PORT OPERATION
The audio output port is a four-wire synchronous serial
interface that may operate in either Slave or Master mode.
The SDOUT output (pin 23) is the serial audio data output.
Audio data is output at this pin in one of four data formats:
Philips I2S, Left Justified, Right Justified, or TDM. The audio
data word length may be 16-, 18-, 20-, or 24-bits. For all word
lengths, the data is triangular PDF dithered from the internal
28-bit data path. The data formats (with the exception of
TDM mode) are shown in Figure 6, while critical timing
parameters are shown in Figure 7 and listed in the Electrical
Characteristics table. The TDM format and timing are shown
in Figures 11 and 12, respectively, while examples of standard TDM configurations are shown in Figures 13 and 14.
The bit clock is either input or output at BCKO (pin 25). In
Slave mode, BCKO is configured as an input pin, and may
operate at rates from 32fS to 128fS, with a minimum of one
clock cycle for each data bit. The exception is the TDM
mode, where the BCKO must operate at N x 64fS, where N
is equal to the number of SRC4190 devices included on the
TDM interface. In Master mode, BCKO operates at a fixed
rate of 64fS for all data formats except TDM, where BCKO
operates at the reference clock (RCKI) frequency. Additional
information regarding TDM mode operation is included in the
Applications Information section of this data sheet.
LRCKO
tSOH
BCKO
tSOL
tDOPD
SDOUT
tDOH
FIGURE 7. Output Port Timing.
The left/right word clock, LRCKO (pin 24), may be configured
as an input or output pin. In Slave mode, LRCKO is an input
pin, while in Master mode it is an output pin. In either case,
the clock rate is equal to fS, the output sampling frequency.
The clock duty cycle is fixed to 50% for I2S, Left Justified, and
Right Justified formats in Master mode. The LRCKO pulse
width is fixed to 32 BCKO cycles for the TDM format in
Master mode.
Left Channel
Right Channel
LRCKO
BCKO
SDOUT
MSB
LSB
MSB
LSB
(a) Left Justified Data Format
LRCKO
BCKO
MSB
SDOUT
LSB
MSB
LSB
(b) Right Justified Data Format
LRCKO
BCKO
SDOUT
MSB
LSB
MSB
LSB
(c) I2S Data Format
1/fS
FIGURE 6. Output Data Formats.
18
SRC4190
www.ti.com
SBFS023A
Table 3 illustrates data format selection for the output port.
The OFMT0 (pin 19), OFMT1 (pin 18), OWL0 (pin 17), and
OWL1 (pin 16) inputs are utilized to set the output port data
format and word length.
OFMT1
OFMT0
OUTPUT PORT DATA FORMAT
0
0
Left Justified
0
1
I2S
1
0
TDM
1
1
Right Justified
OWL1
OWL0
OUTPUT PORT DATA WORD LENGTH
0
0
24 Bits
0
1
20 Bits
1
0
18 Bits
1
1
16 Bits
SOFT MUTE FUNCTION
The soft mute function of the SRC4190 may be invoked by
forcing the MUTE input (pin 14) high. The Soft mute function
slowly attenuates the output signal level down to all zeroes
plus ±4LSB of dither. This provides an artifact-free muting of
the audio output port.
READY OUTPUT
The SRC4190 includes an active low ready output named
RDY (pin 15). This is an output from the rate estimator block,
which indicates that the input-to-output sampling frequency
ratio has been determined. The ready signal can be used as
a flag or indicator output. The ready signal can also be
connected to the active high MUTE input (pin 14) to provide
an auto-mute function, so that the output port is muted when
the rate estimator is in transition.
TABLE 3. Output Port Data Format Selection.
APPLICATIONS INFORMATION
BYPASS MODE
The SRC4190 includes a bypass function, which routes the
input port data directly to the output port, bypassing the
ASRC function. Bypass mode may be invoked by forcing the
BYPAS input (pin 9) high. For normal ASRC operation, the
BYPAS pin should be set to 0.
This section of the data sheet provides practical applications
information for hardware and systems engineers who will be
designing the SRC4190 into their end equipment.
No dithering is applied to the output data in bypass mode;
digital attenuation and mute functions are also unavailable in
this mode.
The typical connection diagram for the SRC4190 is shown in
Figure 8. Recommended values for power supply bypass
capacitors are included. These capacitors should be placed
as close to the IC package as possible.
From
Control
Logic
SRC4190
1
2
3
Reference
Clock
RECOMMENDED CIRCUIT CONFIGURATION
4
5
6
7
8
9
10
11
12
13
14
Audio Input
Device
From/To
Control
Logic
LGRP
RCKI
NC
MODE2
MODE1
MODE0
SDIN
BCKI
LRCKI
VIO
DGND
BYPAS
IFMT0
IFMT1
IFMT2
RST
MUTE
BCKO
LRCKO
SDOUT
VDD
DGND
TDMI
OFMT0
OFMT1
OWL0
OWL1
RDY
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VDD = +3.3V
VIO = +1.65V to VDD
To Pin 7
10µF
Audio Output
Device
To Pin 22
0.1µF
0.1µF
To Pin 8
10µF
To Pin 21
FIGURE 8. Typical Connection Diagram for the SRC4190.
SRC4190
SBFS023A
www.ti.com
19
INTERFACING TO DIGITAL AUDIO RECEIVERS
AND TRANSMITTERS
DIT4096, DIT4192
SRC4190
The SRC4190 input and output ports are designed to interface to a variety of audio devices, including receivers
and transmitters commonly used for AES/EBU,
S/PDIF, and CP1201 communications.
LRCKO
SYNC
TX+
BCKO
SCLK
TX–
SDATA
SDOUT
RCKI
Texas Instruments manufactures the DIR1703 digital audio
interface receiver and DIT4096/4192 digital audio transmitters to address these applications.
AES3, S/PDIF
OUTPUT
MCLK
REF Clock
Generator
Figure 9 illustrates interfacing the DIR1703 to the SRC4190
input port. The DIR1703 operates from a single +3.3V supply, which requires the VIO supply (pin 7) for the SRC4190 to
be set to +3.3V for interface compatibility.
DIT Clock
Generator
Clock
Select
Assumes VIO = +3.3V for SRC4190 and DIT4096, DIT4192
SRC4190
DIR1703
AES3, S/PDIF
Input
RCV
DIN
FIGURE 10. Interfacing the SRC4190 to the DIT4096/4192
Digital Audio Interface Transmitter.
LRCKI
LRCKO
BCKO
BCKI
DATA
SDIN
SCKO
RCLI
Like the SRC4190 output port, the DIT4096 and DIT4192
audio serial port may be configured as a Master or Slave. In
cases where the SRC4190 output port is set to Master mode,
it is recommended to use the reference clock source (RCKI)
as the master clock source (MCLK) for the DIT4096/4192, to
ensure that the transmitter is synchronized to the SRC4190
output port data.
Clock
Generator
Clock
Select
Assumes VIO = +3.3V for SRC4190
TDM APPLICATIONS
FIGURE 9. Interfacing the SRC4190 to the DIR1703 Digital
Audio Interface Receiver.
Figure 10 shows the interface between the SRC4190 output
port and the DIT4096 or DIT4192 audio serial port.
Once again, the VIO supplies for both the SRC4190 and
DIT4096/4192 are set to +3.3V for compatibility.
The SRC4190 supports a TDM output mode, which allows
multiple devices to be daisy-chained together to create a
serial frame. Each device occupies one sub-frame within a
frame, and each sub-frame carries two channels (Left followed by Right). Each sub-frame is 64 bits long, with 32 bits
allotted for each channel. The audio data for each channel is
Left Justified within the allotted 32 bits. Figure 11 illustrates
the TDM frame format, while Figure 12 shows the TDM input
timing parameters, which are listed in the Electrical Characteristics table of this data sheet.
LRCKO
BCKO
SDOUT
Left
Right
Sub-Frame 1
Left
Right
Sub-Frame 2
Left
Right
Sub-Frame N
One Frame = 1/fs
N = Number of Daisy-Chained Devices
One Sub-Frame contains 64 bits, with 32 bits per channel.
For each channel, the audio data is Left Justified, MSB first format, with the word length determined by the OWL[1:0] pins/bits.
FIGURE 11. TDM Frame Format.
20
SRC4190
www.ti.com
SBFS023A
devices that can be daisy-chained in TDM mode is dependent upon the output sampling frequency and the BCKO
frequency, leading to the following numerical relationship:
tLROS
LRCKO
tLROH
Number of Daisy-Chained Devices = (fBCKO / fs) / 64
BCKO
Where:
tTDMS
fBCKO = Output Port Bit Clock (BCKO), 27.136 MHz maximum
fs = Output Port Sampling (or LRCKO) Frequency, 212kHz
maximum.
TDMI
tTDMH
This relationship holds true for both Slave and Master modes.
FIGURE 12. Input Timing for TDM Mode.
The frame rate is equal to the output sampling frequency, fs.
The BCKO frequency for the TDM interface is N x 64fs, where
N is the number of devices included in the daisy chain. For
Master mode, the output BCKO frequency is fixed to the
reference clock (RCKI) input frequency. The number of
SRC4190
Slave #N
TDMI
Figures 13 and 14 show typical connection schemes for the
TDM mode. Although the TMS320C671x DSP family is
shown as the audio processing engine in these figures, other
TI digital signal processors with a multi-channel buffered
serial port (McBSPTM) may also function with this arrangement. Interfacing to processors from other manufacturers is
also possible. Refer to Figure 7 in this data sheet, along with
the equivalent serial port timing diagrams shown in the DSP
data sheet, to determine compatibility.
SRC4190
Slave #2
SDOUT
TDMI
TMS320C671x
McBSP
SRC4190
Slave #1
SDOUT
TDMI
SDOUT
DRn
FSRn
LRCKO
LRCKO
LRCKO
BCKO
BCKO
BCKO
RCKI
RCKI
RCKI
n = 0 or 1
CLKRn
CLKIN or CLKSn
Clock
Generator
FIGURE 13. TDM Interface where all Devices are Slaves.
SRC4190
Master
TDMI
SRC4190
Slave #2
SDOUT
DRn
LRCKO
LRCKO
LRCKO
FSRn
BCKO
BCKO
BCKO
RCKI
RCKI
RCKI
SDOUT
TDMI
TMS320C671x
McBSP
SRC4190
Slave #1
TDMI
SDOUT
n = 0 or 1
CLKRn
CLKIN or CLKSn
Clock
Generator
FIGURE 14. TDM Interface where one Device is Master to Multiple Slaves.
SRC4190
SBFS023A
www.ti.com
21
PIN COMPATIBILITY WITH THE ANALOG
DEVICES AD1895 AND AD1896
The SRC4190 is pin-and function-compatible with the AD1895
and AD1896 when observing the guidelines indicated in the
following paragraphs.
Power Supplies. To ensure compatibility, the VDD_IO and
VDD_CORE supplies of the AD1895 and AD1896 must be
set to +3.3V, while the VIO and VDD supplies of the SRC4190
must be set to +3.3V.
Pin 1 connection. For the AD1895, pin 1 is a no connect
(N.C.) pin. For the SRC4190, pin 1 functions as the low group
delay selection input, and should not be left unconnected.
Pin 1 must be connected to either digital ground or the VIO
supply, dependent upon the desired group delay.
Crystal Oscillator. The SRC4190 does not have an on-chip
crystal oscillator. An external reference clock is required at
the RCKI input (pin 2).
22
Reference Clock Frequency. The reference clock input
frequency for the SRC4190 must be no higher than 30 MHz,
in order to match the master clock frequency specification of
the AD1895 and AD1896. In addition, the SRC4190 does not
support the 768fS reference clock rate.
Master Mode Maximum Sampling Frequency. When the
input or output ports are set to Master mode, the maximum
sampling frequency must be limited to 96kHz in order to
support the AD1895 and AD1896 specification. This is despite the fact that the SRC4190 supports a maximum sampling frequency of 212kHz in Master mode. The user should
consider building an option into his or her design to support
the higher sampling frequency of the SRC4190.
Matched Phase Mode. Due to the internal architecture of
the SRC4190, it does not require or support the matched
phase mode of the AD1896. Given multiple SRC4190 devices, if all reference clock (RCKI) inputs are driven from the
same clock source, the devices will be phase matched.
SRC4190
www.ti.com
SBFS023A
PACKAGE OPTION ADDENDUM
www.ti.com
9-Dec-2004
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SRC4190IDB
ACTIVE
SSOP
DB
28
50
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
SRC4190IDBR
ACTIVE
SSOP
DB
28
2000
Pb-Free
(RoHS)
CU NIPDAU
Level-2-260C-1YEAR/
Level-1-220C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2004, Texas Instruments Incorporated