TI SRC4190IDBRQ1

SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
192-kHz STEREO ASYNCHRONOUS SAMPLE-RATE CONVERTER
Check for Samples: SRC4190-Q1
FEATURES
1
•
•
•
•
•
•
•
•
•
•
•
•
•
Qualified for Automotive Applications
Automatic Sensing of the Input-To-Output
Sampling Ratio
Wide Input-to-Output Sampling Range:
16:1 to 1:16
Supports Input and Output Sampling Rates up
to 212 kHz
Dynamic Range: 128 dB (–60 dBFS Input,
BW = 20 Hz to fS/2, A-Weighted)
THD+N: –125 db (0 dBFS Input,
BW = 20 Hz to fS/2)
Attenuates Sampling and Reference Clock
Jitter
High Performance, Linear Phase Digital
Filtering
Flexible Audio Serial Ports
Master or Slave Mode Operation
Supports I2S, Left Justified, Right Justified,
and TDM Data Formats
Supports 16, 18, 20, or 24-Bit Audio Data
TDM Mode Allows Daisy Chaining of up to
Eight Devices
•
•
•
•
•
•
•
•
•
Supports 24-, 20-, 18-, or 16-Bit Input and
Output Data
All Output Data Is Dithered From the Internal
28-Bit Data Path
Low Group Delay Option for Interpolation
Filter
Soft Mute Function
Bypass Mode
Power Down Mode
Operates From a Single 3.3-V Power Supply
Small SSOP-28 Package
Pin Compatible With the SRC4192, AD1895,
and AD1896
APPLICATIONS
•
•
•
•
•
•
Digital Mixing Consoles
Digital Audio Workstations
Audio Distribution Systems
Broadcast Studio Equipment
High-End A/V Receivers
General Digital Audio Processing
DESCRIPTION
The SRC4190 is an asynchronous sample rate converter designed for professional and broadcast audio
applications. The SRC4190 combines a wide input-to-output sampling ratio with outstanding dynamic range and
low distortion. Input and output serial ports support standard audio formats, as well as a Time Division
Multiplexed (TDM) mode. Flexible audio interfaces allow the SRC4190 to connect to a wide range of audio data
converters, digital audio receivers and transmitters, and digital signal processors.
The SRC4190 is a standalone pin-programmed device, with control pins for mode, data format, mute, bypass,
and low group delay functions.
The SRC4190 may be operated from a single 3.3-V power supply. A separate digital I/O supply (VIO) operates
over the 1.65-V to 3.6-V supply range, allowing greater flexibility when interfacing to current and future
generation signal processors and logic devices. The SRC4190 is available in an SSOP-28 package.
ORDERING INFORMATION (1)
TA
–40°C to 85°C
(1)
(2)
PACKAGE
SSOP – DB
(2)
Reel of 2000
ORDERABLE PART NUMBER
SRC4190IDBRQ1
TOP-SIDE MARKING
SRC4190Q
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2009, Texas Instruments Incorporated
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
DB PACKAGE
(TOP VIEW)
LGRP
RCKI
NC
SDIN
BCKI
LRCKI
VIO
DGND
BYPAS
IFMT0
IFMT1
IFMT2
RST
MUTE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
16
15
MODE2
MODE1
MODE0
BCKO
LRCKO
SDOUT
VDD
DGND
TDMI
OFMT0
OFMT1
OWL0
OWL1
RDY
TERMINAL FUNCTIONS
TERMINAL
DESCRIPTION
NAME
NO.
LGRP
1
Low group delay control input (active high)
RCKI
2
Reference clock input
NC
3
No internal connection
SDIN
4
Audio serial data input
BCKI
5
Input port bit clock I/O
LRCKI
6
Input port left/right word clock I/O
VIO
7
Digital I/O supply, 1.65 V to VDD
DGND
8
Digital ground
BYPAS
9
ASRC bypass control input (active high)
IFMT0
10
Input port data format control input
IFMT1
11
Input port data format control input
IFMT2
12
Input port data format control input
RST
13
Reset input (active low)
MUTE
14
Output mute control input (active high)
RDY
15
ASRC ready status output (active low)
OWL1
16
Output port data word length control input
OWL0
17
Output port data word length control input
OFMT1
18
Output port data format control input
OFMT0
19
Output port data format control input
TDMI
20
TDM data input (connect to DGND when not in use)
DGND
21
Digital ground
VDD
22
Digital core supply, 3.3 V
SDOUT
23
Audio serial data output
LRCKO
24
Output port left/right word clock I/O
BCKO
25
Output port bit clock I/O
MODE0
26
Serial port mode control input
MODE1
27
Serial port mode control input
MODE2
28
Serial port mode control input
2
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
ABSOLUTE MAXIMUM RATINGS (1)
over operating free-air temperature range (unless otherwise noted)
VDD
Core supply voltage range
–0.3 V to 4 V
VIO
I/O supply voltage range
–0.3 V to 4 V
VI
Digital input voltage
–0.3 V to 4 V
TA
Operating free-air temperature range
–40°C to 85°C
Tstg
Storage temperature range
–65°C to 150°C
(1)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Dynamic Performance (1)
Resolution
24
bits
fSIN
Input sampling frequency
4
212
kHz
fSOUT
Output sampling frequency
4
212
kHz
Input:output sampling ratio
Dynamic range
Total harmonic distortion +
noise
1:16
Downsampling
BW = 20 Hz to fSOUT/2,
–60-dBFS Input,
fIN = 1 kHz, Unweighted
(add 3 dB to specification
for A-weighted result)
BW = 20 Hz to fSOUT/2,
0-dBFS Input,
fIN = 1 kHz, Unweighted
16:1
44.1 kHz : 48 kHz
125
48 kHz : 44.1 kHz
125
48 kHz : 96 kHz
125
44.1 kHz : 192 kHz
125
96 kHz : 48 kHz
125
192 kHz : 12 kHz
125
192 kHz : 32 kHz
125
192 kHz : 48 kHz
125
32 kHz : 48 kHz
125
12 kHz : 192 kHz
125
44.1 kHz : 48 kHz
–125
48 kHz : 44.1 kHz
–125
48 kHz : 96 kHz
–125
44.1 kHz : 192 kHz
–125
96 kHz : 48 kHz
–125
192 kHz : 12 kHz
–125
192 kHz : 32 kHz
–125
192 kHz : 48 kHz
–125
32 kHz : 48 kHz
–125
12 kHz : 192 kHz
–125
dB
dB
Interchannel gain mismatch
0
dB
Interchannel phase deviation
0
°
Mute attenuation
(1)
Upsampling
24-bit word length, A-weighted
–128
dB
Dynamic performance measured with an Audio Precision System Two Cascade or Cascade Plus.
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
3
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Digital Interpolation Filter Characteristics
Passband
Passband ripple
0.4535 ×
fSIN
Hz
±0.007
dB
0.5465 ×
fSIN
Hz
Transition band
0.4535 ×
fSIN
Stop band
0.5465 ×
fSIN
Hz
–125
dB
Stop band attenuation
Normal group delay time
(LGRP = 0)
102.53125
/ fSIN
s
Low group delay time
(LGRP = 1)
70.53125 /
fSIN
s
Digital Decimation Filter Characteristics
Passband
Passband ripple
Transition band
0.4535 ×
fSOUT
Stop band
0.5465 ×
fSOUT
Stop band attenuation
0.4535 ×
fSOUT
Hz
±0.008
dB
0.5465 ×
fSOUT
Hz
Hz
–125
dB
36.46875 /
fSOUT
Group delay
s
Digital I/O Characteristics
VIH
High-level input voltage
0.7 × VIO
VIO
V
VIL
Low-level input voltage
0
0.3 × VIO
V
IIH
High-level input current
0.5
10
μA
IIL
Low-level input current
0.5
10
μA
VOH
High-level output voltage
IO = –4 mA
VIO
V
VOL
Low-level output voltage
IO = 4 mA
CIN
Input capacitance
4
0.8 × VIO
0
0.2 × VIO
3
Submit Documentation Feedback
V
pF
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
ELECTRICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
128 ×
fSMIN
50
MHz
20
1/(128 ×
fSMIN)
Switching Characteristics
fRCKI
RCKI frequency (2)
(3)
tRCKIP
RCKI pulse duration
tRCKIH
RCKI pulse duration, high
0.4 ×
tRCKIP
ns
tRCKIL
RCKI pulse duration, low
0.4 ×
tRCKIP
ns
tRSTL
RST pulse duration, low
500
ns
tLRIS
LRCKI to BCKI setup time
10
ns
tSIH
BCKI pulse duration, high
10
ns
tSIL
BCKI pulse duration, low
10
ns
tLDIS
SDIN data setup time
10
ns
tLDIH
SDIN data hold time
10
tDOPD
SDOUT data delay time
tDOH
SDOUT data hold time
2
ns
tSOH
BCKO pulse duration, high
10
ns
tSOL
BCKO pulse duration, low
5
ns
tLROS
LRCKO setup time
10
ns
tLROH
LRCKO hold time
10
ns
tTDMS
TDMI data setup time
10
ns
tTDMH
TDMI data hold time
10
ns
ns
ns
10
ns
Power Supplies
VDD
Core supply voltage
VIO
Digital I/O supply voltage
IDDPD
VDD supply current, power
down
IDDD
VDD supply current, dynamic
IIOPD
VIO supply current, power
down
IIOD
VIO supply current, dynamic
PD
Total power dissipation,
power down
PD
(2)
(3)
Total power dissipation,
dynamic
3
3.3
3.6
V
1.65
3.3
3.6
V
100
μA
RST = 0, No clocks
VDD = 3.3 V, VIO = 3.3 V
fSIN = fSOUT = 192 kHz
66
RST = 0, No clocks
fSIN = fSOUT = 192 kHz
mA
100
2
RST = 0, No clocks
μA
mA
660
μW
VDD = 3.3 V, VIO = 3.3 V
fSIN = fSOUT = 192 kHz
225
mW
fSMIN = min (fSIN, fSOUT)
fSMAX = max (fSIN, fSOUT)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
5
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
TYPICAL CHARACTERISTICS
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
FFT with 1kHz INPUT TONE at 0dBFS
(12kHz:192kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(12kHz:192kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
20k
40k
60k
80k
96k
0
40k
60k
80k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(32kHz:48kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(32kHz:48kHz)
0
–60
–20
–70
96k
–80
–40
–90
–60
–100
dBFS
dBFS
20k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k
0
24k
10k
15k
20k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(44.1kHz:48kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(44.1kHz:48kHz)
0
–60
–20
–70
24k
–80
–40
–90
–60
–100
dBFS
dBFS
5k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k
24k
0
Frequency (Hz)
6
5k
10k
15k
20k
24k
Frequency (Hz)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
FFT with 1kHz INPUT TONE at 0dBFS
(44.1kHz:96kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(44.1kHz:96kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
10k
20k
30k
40k
48k
0
20k
30k
40k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(44.1kHz:192kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(44.1kHz:192kHz)
0
–60
–20
–70
48k
–80
–40
–90
–60
–100
dBFS
dBFS
10k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
20k
40k
60k
80k
0
96k
40k
60k
80k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(48kHz:44.1kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(48kHz:44.1kHz)
0
–60
–20
–70
96k
–80
–40
–90
–60
–100
dBFS
dBFS
20k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k 22k
0
Frequency (Hz)
5k
10k
15k
20k 22k
Frequency (Hz)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
7
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
FFT with 1kHz INPUT TONE at 0dBFS
(48kHz:96kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(48kHz:96kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
10k
20k
30k
40k
48k
0
20k
30k
40k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(48kHz:192kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(48kHz:192kHz)
0
–60
–20
–70
48k
–80
–40
–90
–60
–100
dBFS
dBFS
10k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
20k
40k
60k
80k
96k
0
40k
60k
80k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(96kHz:44.1kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(96kHz:44.1kHz)
0
–60
–20
–70
96k
–80
–40
–90
–60
–100
dBFS
dBFS
20k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k 22k
0
Frequency (Hz)
8
5k
10k
15k
20k 22k
Frequency (Hz)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
FFT with 1kHz INPUT TONE at 0dBFS
(96kHz:48kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(96kHz:48kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k
24k
0
10k
15k
20k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(96kHz:192kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(96kHz:192kHz)
0
–60
–20
–70
24k
–80
–40
–90
–60
–100
dBFS
dBFS
5k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
20k
40k
60k
80k
96k
0
20k
40k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(192kHz:12kHz)
80k
96k
FFT with 1kHz INPUT TONE at –60dBFS
(192kHz:12kHz)
0
–60
–20
–70
–80
–40
–90
–60
–100
dBFS
dBFS
60k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
1k
2k
3k
4k
5k
6k
0
Frequency (Hz)
1k
2k
3k
4k
5k
6k
Frequency (Hz)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
9
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
FFT with 1kHz INPUT TONE at 0dBFS
(192kHz:32kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(192kHz:12kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
2.5k
5k
7.5k
10k
12.5k
15k 16k
0
5k
7.5k
10k
12.5k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(192kHz:44.1kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(192kHz:44.1kHz)
0
–60
–20
–70
15k 16k
–80
–40
–90
–60
–100
dBFS
dBFS
2.5k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k 22k
0
10k
15k
20k 22k
Frequency (Hz)
FFT with 1kHz INPUT TONE at 0dBFS
(192kHz:48kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(192kHz:48kHz)
0
–60
–20
–70
–80
–40
–90
–60
–100
dBFS
dBFS
5k
Frequency (Hz)
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
0
5k
10k
15k
20k
24k
0
10
5k
10k
15k
20k
24k
Frequency (Hz)
Frequency (Hz)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
FFT with 1kHz INPUT TONE at 0dBFS
(192kHz:96kHz)
FFT with 1kHz INPUT TONE at –60dBFS
(192kHz:96kHz)
0
–60
–20
–70
–80
–40
–90
–100
dBFS
dBFS
–60
–80
–100
–110
–120
–130
–120
–140
–140
–150
–160
–160
–170
10k
20k
30k
40k
48k
0
20k
30k
40k
Frequency (Hz)
FFT with 20kHz INPUT TONE at 0dBFS
(44.1kHz:48kHz)
FFT with 20kHz INPUT TONE at 0dBFS
(48kHz:44.1kHz)
0
0
–20
–20
–40
–40
–60
–60
–80
–100
–100
–120
–140
–140
–160
–160
5k
10k
15k
20k
48k
–80
–120
0
10k
Frequency (Hz)
dBFS
dBFS
0
24k
0
5k
10k
15k
20k 22k
Frequency (Hz)
Frequency (Hz)
FFT with 20kHz INPUT TONE at 0dBFS
(48kHz:96kHz)
FFT with 20kHz INPUT TONE at 0dBFS
(96kHz:48kHz)
–20
–40
–40
–60
–60
dBFS
dBFS
0
–20
–80
–100
–80
–100
–120
–120
–140
–140
–160
–160
0
10k
20k
30k
40k
48k
0
5k
10k
15k
20k
24k
Frequency (Hz)
Frequency (Hz)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
11
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
FFT with 80kHz INPUT TONE at 0dBFS
(192kHz:192kHz)
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(44.1kHz:48kHz)
0
Total Harmonic Distortion+Noise (dB)
–100
–20
–40
dBFS
–60
–80
–100
–120
–140
–160
0
20k
40k
60k
80k
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–140
96k
–120
Frequency (Hz)
Total Harmonic Distortion+Noise (dB)
Total Harmonic Distortion+Noise (dB)
–110
–115
–120
–125
–130
–135
–140
–145
–120
–100
–80
–60
–40
–20
–20
0
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–140
0
–120
–100
–80
–60
–40
–20
Input Amplitude (dBFS)
Input Amplitude (dBFS)
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(96kHz:48kHz)
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(44.1kHz:192kHz)
0
–100
Total Harmonic Distortion+Noise (dB)
Total Harmonic Distortion+Noise (dB)
–40
–100
–105
–100
–105
–110
–115
–120
–125
–130
–135
–140
–145
–120
–100
–80
–60
–40
–20
0
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–140
Input Amplitude (dBFS)
12
–60
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(48kHz:96kHz)
–100
–150
–140
–80
Input Amplitude (dBFS)
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(48kHz:44.1kHz)
–150
–140
–100
–120
–100
–80
–60
–40
–20
0
Input Amplitude (dBFS)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
THD+N vs INPUT FREQUENCY WITH 0dBFS INPUT
(44.1kHz:48kHz)
THD+N vs INPUT AMPLITUDE fIN = 1kHz
(192kHz:44.1kHz)
–100
Total Harmonic Distortion+Noise (dB)
Total Harmonic Distortion+Noise (dB)
–100
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–140
–100
–80
–60
–40
–20
–115
–120
–125
–130
–135
–140
–145
0
0
5k
10k
15k
Input Amplitude (dBFS)
Input Frequency (Hz)
THD+N vs INPUT FREQUENCY WITH 0dBFS INPUT = 1kHz
(48kHz:44.1kHz)
THD+N vs INPUT FREQUENCY WITH 0dBFS
(48kHz:96kHz)
20k
–100
Total Harmonic Distortion+Noise (dB)
Total Harmonic Distortion+Noise (dB)
–110
–150
–120
–100
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
0
5k
10k
15k
20k
0
5k
10k
15k
Input Frequency (Hz)
Input Frequency (Hz)
THD+N vs INPUT FREQUENCY WITH 0dBFS
(96kHz:48kHz)
THD+N vs INPUT FREQUENCY WITH 0dBFS
(44.1kHz:192kHz)
–100
20k
–100
Total Harmonic Distortion+Noise (dB)
Total Harmonic Distortion+Noise (dB)
–105
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
–105
–110
–115
–120
–125
–130
–135
–140
–145
–150
0
5k
10k
15k
20k
0
5k
10k
15k
20k
Input Frequency (Hz)
Input Frequency (Hz)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
13
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
LINEARITY with fIN = 200Hz
(44.1kHz:48kHz)
THD+N vs INPUT FREQUENCY WITH 0dBFS
(192kHz:44.1kHz)
–105
–110
Output Amplitude (dBFS)
Total Harmonic Distortion+Noise (dB)
–100
–115
–120
–125
–130
–135
–140
–145
–150
0
5k
10k
15k
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
20k
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
Input Frequency (Hz)
LINEARITY with fIN = 200Hz
(48kHz:96kHz)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
Output Amplitude (dBFS)
Output Amplitude (dBFS)
LINEARITY with fIN = 200Hz
(48kHz:44.1kHz)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
0
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
Input Amplitude (dBFS)
Input Amplitude (dBFS)
LINEARITY with fIN = 200Hz
(96kHz:48kHz)
LINEARITY with fIN = 200Hz
(44.1kHz:192kHz)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
Output Amplitude (dBFS)
Output Amplitude (dBFS)
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
0
0
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
Input Amplitude (dBFS)
14
0
Input Amplitude (dBFS)
0
Input Amplitude (dBFS)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
TYPICAL CHARACTERISTICS (continued)
TA = 25°C, VDD = 3.3 V, and VIO = 3.3 V (unless otherwise noted)
FREQUENCY RESPONSE with 0dBFS INPUT
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
dBFS
Output Amplitude (dBFS)
LINEARITY with fIN = 200Hz
(192kHz:44.1kHz)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
–100
–110
–120
–130
192kHz:48kHz
192kHz:32kHz
192kHz:96kHz
0
–130 –120 –110 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10
10k
20k
0
30k
40k
50k
60k
Frequency (Hz)
Input Amplitude (dBFS)
PASS BAND RIPPLE
(192k:48k)
0
–0.01
–0.02
–0.03
–0.04
–0.05
–0.06
–0.07
–0.08
–0.09
–0.10
–0.11
–0.12
–0.13
–0.14
–0.15
(dBFS)
(dBFS)
PASS BAND RIPPLE
(48k:48k)
0
5k
10k
15k
20k 22k
0
–0.01
–0.02
–0.03
–0.04
–0.05
–0.06
–0.07
–0.08
–0.09
–0.10
–0.11
–0.12
–0.13
–0.14
–0.15
0
Input Frequency (Hz)
5k
10k
15k
20k 22k
Input Frequency (Hz)
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
15
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
DETAILED DESCRIPTION
The SRC4190 is an asynchronous sample rate converter (ASRC) designed for professional audio applications.
Operation at input and output sampling frequencies up to 212 kHz is supported, with an input/output sampling
ratio range of 16:1 to 1:16. Excellent dynamic range and Total Harmonic Distortion + Noise (THD+N) are
achieved by employing high performance and linear phase digital filtering. Digital filtering options allow for lower
group delay processing.
The audio input and output ports support standard audio data formats, as well as a TDM interface mode. Word
lengths of 24, 20, 18, and 16 bits are supported. Both ports may operate in slave mode, deriving their word and
bit clocks from external input and output devices. Alternatively, one port may operate in master mode while the
other remains in slave mode. In master mode, the LRCK and BCK clocks are derived from the reference clock
input, RCKI. The flexible configuration of the input and output ports allows connection to a wide variety of audio
data converters, interface devices, digital signal processors, and programmable logic.
A bypass mode is included, which allows audio data to be passed directly from the input port to the output port,
bypassing the ASRC function. The bypass option is useful for passing through encoded or compressed audio
data, or nonaudio control or status data.
A soft mute function is available providing artifact-free operation while muting the audio output signal. The mute
attenuation is typically –128 dB.
Functional Block Diagram
Figure 1 shows a functional block diagram of the SRC4190. Audio data is received at the input port, clocked by
either the audio data source in Slave mode or by the SRC4190 in Master mode. The output port data is clocked
by either the audio data source in Slave mode, or by the SRC4190 in Master mode. The input data is passed
through interpolation filters which up-sample the data, which is then passed on to the re-sampler. The rate
estimator compares the input and output sampling frequencies by comparing LRCKI, LRCKO, and a reference
clock. The results include an offset for the FIFO pointer and the coefficients needed for re-sampling function.
The output of the re-sampler is then passed on to the decimation filter. The decimation filter performs
down-sampling and anti-alias filtering functions.
16
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
LRCKI
Audio
Input
Port
BCKI
SDIN
fSIN
Interpolation
Filters
16fSIN
Re-Sampler
16fSOUT
MODE [2:0]
IFMT [2:0]
REFCLK
OFMT [1:0]
LRCKI
OWL [1:0]
Control
Logic
MUTE
Rate
Estimator
BYPAS
LGRP
RST
LRCKO
fSOUT
RDY
Decimation
Filters
LRCKO
Audio
Output
Port
BCKO
SDOUT
TDMI
VDD
DGND
Power
Reference
Clock
RCKI
REFCLK
VIO
DGND
Figure 1. Functional Block Diagram
Reference Clock
The SRC4190 requires a reference clock for operation. The reference clock is applied at the RCKI input, pin 2.
Figure 2 illustrates the reference clock connections and requirements for the SRC4190. The reference clock may
operate at 128fS, 256fS, or 512fS, where fS is the input or output sampling frequency. The maximum external
reference clock input frequency is 50 MHz.
SRC4190
RCKI
2
From External
Clock Source
50MHz max
tRCKIP
RCKI
tRCKIH
tRCKIL
tRCKIP > 20ns min
tRCKIH > 0.4 tRCKIP
tRCKIL > 0.4 tRCKIP
Figure 2. Reference Clock Input Connections and Timing Requirements
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
17
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
Reset and Power Down Operation
The SRC4190 may be reset using the RST input (pin 13). There is no internal power on reset, so the user should
force a reset sequence after power up in order to initialize the device. In order to force a reset, the reference
clock input must be active, with an external clock source supplying a valid reference clock signal (see Figure 2).
The user must assert RST low for a minimum of 500 ns and then bring RST high again to force a reset. Figure 3
shows the reset timing for the SRC4190.
The SRC4190 also supports a power-down mode. Powerdown mode may be set by holding the RST input low.
RCKI
RST
tRSTL > 500ns
Figure 3. Reset Pulse Width Requirement
Audio Port Modes
The SRC4190 supports seven serial port modes, which are shown in Table 1. The audio port mode is selected
using the MODE0 (pin 26), MODE1 (pin 27), and MODE2 (pin 28) inputs.
In slave mode, the port LRCK and BCK clocks are configured as inputs, and receive their clocks from an external
audio device. In master mode, the LRCK and BCK clocks are configured as outputs, being derived from the
reference clock input (RCKI). Only one port can be set to master mode at any given time, as indicated in Table 1.
Table 1. Setting the Serial Port Modes
MODE2
MODE1
MODE0
0
0
0
Both input and output ports are slave mode
SERIAL PORT MODE
0
0
1
Output port is master mode with RCKI = 128fS
0
1
0
Output port is master mode with RCKI = 512fS
0
1
1
Output port is master mode with RCKI = 256fS
1
0
0
Both input and output ports are slave mode
1
0
1
Input port is master mode with RCKI = 128fS
1
1
0
Input port is master mode with RCKI = 512fS
1
1
1
Input port is master mode with RCKI = 256fS
Input Port Operation
The audio input port is a three-wire synchronous serial interface that may operate in either slave or master mode.
The SDIN input (pin 4) is the serial audio data input. Audio data is input at this pin in one of three standard audio
data formats: Philips I2S, left justified, or right justified. The audio data word length may be up to 24 bits for I2S
and left justified formats, while the right justified format supports 16-, 18-, 20-, or 24-bit data. The data formats
are shown in Figure 4, while critical timing parameters are shown in Figure 5 and listed in the Electrical
Characteristics table.
The bit clock is either an input or output at BCKI (pin 5). In slave mode, BCKI is configured as an input pin, and
may operate at rates from 32fS to 128fS, with a minimum of one clock cycle per data bit. In master mode, BCKI
operates at a fixed rate of 64fS.
18
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
Left Channel
Right Channel
LRCKO
BCKI
SDIN
MSB
LSB
MSB
LSB
(a) Left Justified Data Format
LRCKI
BCKI
MSB
SDIN
LSB
MSB
LSB
(b) Right Justified Data Format
LRCKI
BCKI
SDIN
MSB
LSB
MSB
LSB
(c) I2S Data Format
1/fS
Figure 4. Input Data Formats
LRCKI
tLRIS
tSIH
BCKI
tLDIS
tSIL
SDIN
tLDIH
Figure 5. Input Port Timing
The left/right word clock, LRCKI (pin 6), may be configured as an input or output pin. In slave mode, LRCKI is an
input pin, while in master mode LRCKI is an output pin. In either case, the clock rate is equal to fS, the input
sampling frequency. The LRCKI duty cycle is fixed to 50% for master mode operation.
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
19
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
Table 2 illustrates data format selection for the input port. The IFMT0 (pin 10), IFMT1 (pin 11), and IFMT2 (pin
12) inputs are utilized to set the input port data format.
Table 2. Input Port Data Format Selection
IFMT2
IFMT1
IFMT0
INPUT PORT DATA FORMAT
0
0
0
24-bit left justified
0
0
1
24-bit I2S
0
1
0
Unused
0
1
1
Unused
1
0
0
16-bit right justified
1
0
1
18-bit right justified
1
1
0
20-bit right justified
1
1
1
24-bit right justified
Output Port Operation
The audio output port is a four-wire synchronous serial interface that may operate in either slave or master
mode. The SDOUT output (pin 23) is the serial audio data output. Audio data is output at this pin in one of four
data formats: Philips I2S, left justified, right justified, or TDM. The audio data word length may be 16, 18, 20, or
24 bits. For all word lengths, the data is triangular PDF dithered from the internal 28-bit data path. The data
formats (with the exception of TDM mode) are shown in Figure 6, while critical timing parameters are shown in
Figure 7 and listed in the Electrical Characteristics table. The TDM format and timing are shown in Figure 11 and
Figure 12, respectively, while examples of standard TDM configurations are shown in Figure 13 and Figure 14.
The bit clock is either input or output at BCKO (pin 25). In slave mode, BCKO is configured as an input pin, and
may operate at rates from 32fS to 128fS, with a minimum of one clock cycle for each data bit. The exception is
the TDM mode, where the BCKO must operate at N × 64fS, where N is equal to the number of SRC4190 devices
included on the TDM interface. In master mode, BCKO operates at a fixed rate of 64fS for all data formats except
TDM, where BCKO operates at the reference clock (RCKI) frequency. Additional information regarding TDM
mode operation is included in the Application Information section of this data sheet.
The left/right word clock, LRCKO (pin 24), may be configured as an input or output pin. In slave mode, LRCKO is
an input pin, while in master mode it is an output pin. In either case, the clock rate is equal to fS, the output
sampling frequency. The clock duty cycle is fixed to 50% for I2S, left justified, and right justified formats in master
mode. The LRCKO pulse width is fixed to 32 BCKO cycles for the TDM format in master mode.
20
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
Left Channel
Right Channel
LRCKO
BCKO
SDOUT
MSB
LSB
MSB
LSB
(a) Left Justified Data Format
LRCKO
BCKO
MSB
SDOUT
LSB
MSB
LSB
(b) Right Justified Data Format
LRCKO
BCKO
SDOUT
MSB
LSB
MSB
LSB
(c) I2S Data Format
1/fS
Figure 6. Output Data Formats
LRCKO
tSOH
BCKO
tSOL
tDOPD
SDOUT
tDOH
Figure 7. Output Port Timing
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
21
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
Table 3 illustrates data format selection for the output port. The OFMT0 (pin 19), OFMT1 (pin 18), OWL0 (pin
17), and OWL1 (pin 16) inputs are utilized to set the output port data format and word length.
Table 3. Output Port Data Format Selection
OFMT1
OFMT0
OUTPUT PORT DATA FORMAT
0
0
Left justified
0
1
I2S
1
0
TDM
1
1
Right justified
OWL1
OWL0
OUTPUT PORT DATA WORD LENGTH
0
0
24 bits
0
1
20 bits
1
0
18 bits
1
1
16 bits
Bypass Mode
The SRC4190 includes a bypass function, which routes the input port data directly to the output port, bypassing
the ASRC function. Bypass mode may be invoked by forcing the BYPAS input (pin 9) high. For normal ASRC
operation, the BYPAS pin should be set to 0.
No dithering is applied to the output data in bypass mode; digital attenuation and mute functions are also
unavailable in this mode.
Soft Mute Function
The soft mute function of the SRC4190 may be invoked by forcing the MUTE input (pin 14) high. The Soft mute
function slowly attenuates the output signal level down to all zeroes plus ±4 LSB of dither. This provides an
artifact-free muting of the audio output port.
Ready Output
The SRC4190 includes an active-low ready output named RDY (pin 15). This is an output from the rate estimator
block, which indicates that the input-to-output sampling frequency ratio has been determined. The ready signal
can be used as a flag or indicator output. The ready signal can also be connected to the active-high MUTE input
(pin 14) to provide an auto-mute function, so that the output port is muted when the rate estimator is in transition.
22
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
APPLICATION INFORMATION
This section of the data sheet provides practical applications information for hardware and systems engineers
who will be designing the SRC4190 into end equipment.
Recommended Circuit Configuration
The typical connection diagram for the SRC4190 is shown in Figure 8. Recommended values for power-supply
bypass capacitors are included. These capacitors should be placed as close to the IC package as possible.
From
Control
Logic
SRC4190
1
2
3
Reference
Clock
4
5
6
7
8
9
10
11
12
13
14
Audio Input
Device
From/To
Control
Logic
LGRP
RCKI
NC
MODE2
MODE1
MODE0
SDIN
BCKI
LRCKI
VIO
DGND
BYPAS
IFMT0
IFMT1
IFMT2
RST
MUTE
BCKO
LRCKO
SDOUT
VDD
DGND
TDMI
OFMT0
OFMT1
OWL0
OWL1
RDY
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VDD = +3.3V
VIO = +1.65V to V DD
10µF
Audio Output
Device
To Pin 7
To Pin 22
To Pin 8
To Pin 21
0.1µF
0.1µF
10µF
Figure 8. Typical Connection Diagram
Interfacing to Digital Audio Receivers and Transmitters
The SRC4190 input and output ports are designed to interface to a variety of audio devices, including receivers
and transmitters commonly used for AES/EBU, S/PDIF, and CP1201 communications.
Texas Instruments manufactures the DIR1703 digital audio interface receiver and DIT4096/4192 digital audio
transmitters to address these applications.
Figure 9 illustrates interfacing the DIR1703 to the SRC4190 input port. The DIR1703 operates from a single
3.3-V supply, which requires the VIO supply (pin 7) for the SRC4190 to be set to 3.3 V for interface compatibility.
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
23
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
www.ti.com
SRC4190
DIR1703
LRCKI
LRCKO
AES3, S/PDIF
Input
RCV
DIN
BCKO
BCKI
DATA
SDIN
SCKO
RCLI
Clock
Generator
Clock
Select
Assumes V IO = +3.3V for SRC4190
Figure 9. Interfacing the SRC4190 to the DIR1703 Digital Audio Interface Receiver
Figure 10 shows the interface between the SRC4190 output port and the DIT4096 or DIT4192 audio serial port.
Once again, the VIO supplies for both the SRC4190 and DIT4096/4192 are set to 3.3 V for compatibility.
SRC4190
DIT4096, DIT4192
LRCKO
SYNC
TX+
BCKO
SCLK
TXÐ
SDOUT
SDATA
RCKI
AES3, S/PDIF
OUTPUT
MCLK
REF Clock
Generator
DIT Clock
Generator
Clock
Select
Assumes V IO = +3.3V for SRC4190 and DIT4096, DIT4192
Figure 10. Interfacing the SRC4190 to the DIT4096/4192 Digital Audio Interface Transmitter
Like the SRC4190 output port, the DIT4096 and DIT4192 audio serial port may be configured as a Master or
Slave. In cases where the SRC4190 output port is set to Master mode, it is recommended to use the reference
clock source (RCKI) as the master clock source (MCLK) for the DIT4096/4192, to ensure that the transmitter is
synchronized to the SRC4190 output port data.
TDM Applications
The SRC4190 supports a TDM output mode, which allows multiple devices to be daisy-chained together to
create a serial frame. Each device occupies one sub-frame within a frame, and each sub-frame carries two
channels (Left followed by Right). Each sub-frame is 64 bits long, with 32 bits allotted for each channel. The
audio data for each channel is left justified within the allotted 32 bits. Figure 11 illustrates the TDM frame format,
while Figure 12 shows the TDM input timing parameters, which are listed in the Electrical Characteristics table of
this data sheet.
24
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
SRC4190-Q1
www.ti.com
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
LRCKO
BCKO
SDOUT
Left
Right
Left
Sub-Frame 1
Right
Sub-Frame 2
Left
Right
Sub-Frame N
One Frame = 1/f s
N = Number of Daisy-Chained Devices
One Sub-Frame contains 64 bits, with 32 bits per channel.
For each channel, the audio data is Left Justified, MSB first format, with the word length determined by the OWL[1:0] pins/bits .
Figure 11. TDM Frame Format
tLROS
LRCKO
tLROH
BCKO
tTDMS
TDMI
tTDMH
Figure 12. TDM Input Timing
The frame rate is equal to the output sampling frequency, fS. The BCKO frequency for the TDM interface is N ×
64fS, where N is the number of devices included in the daisy chain. For Master mode, the output BCKO
frequency is fixed to the reference clock (RCKI) input frequency. The number of devices that can be
daisy-chained in TDM mode is dependent upon the output sampling frequency and the BCKO frequency, leading
to the following numerical relationship:
Number of daisy-chained devices = (fBCKO / fS) / 64
Where:
fBCKO = Output port bit clock (BCKO), 27.136 MHz maximum
fS = Output port sampling (or LRCKO) frequency, 212 kHz maximum
This relationship holds true for both slave and master modes.
Figure 13 and Figure 14 show typical connection schemes for the TDM mode. Although the TMS320C671x DSP
family is shown as the audio processing engine in these figures, other TI digital signal processors with a
multi-channel buffered serial port (McBSPTM) may also function with this arrangement. Interfacing to processors
from other manufacturers is also possible. See Figure 7 in this data sheet, along with the equivalent serial port
timing diagrams shown in the DSP data sheet, to determine compatibility.
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
25
SRC4190-Q1
SBFS034A – SEPTEMBER 2008 – REVISED OCTOBER 2009
SRC4190
Slave #N
TDMI
www.ti.com
SRC4190
Slave #2
TDMI
SDOUT
SRC4190
Slave #1
SDOUT
TDMI
TMS320C671x
McBSP
SDOUT
DRn
FSRn
LRCKO
LRCKO
LRCKO
BCKO
BCKO
BCKO
RCKI
RCKI
RCKI
n = 0 or 1
CLKRn
CLKIN or CLKSn
Clock
Generator
Figure 13. TDM Interface Where All Devices are Slaves
SRC4190
Master
TDMI
SRC4190
Slave #2
SDOUT
DRn
LRCKO
LRCKO
LRCKO
FSRn
BCKO
BCKO
BCKO
RCKI
RCKI
RCKI
SDOUT
TDMI
TMS320C671x
McBSP
SRC4190
Slave #1
SDOUT
TDMI
n = 0 or 1
CLKRn
CLKIN or CLKSn
Clock
Generator
Figure 14. TDM Interface Where One Device is Master to Multiple Slaves
Pin Compatibility With the Analog Devices AD1895 and AD1896
The SRC4190 is pin-compatible and function-compatible with the AD1895 and AD1896 when observing the
guidelines indicated in the following paragraphs.
Power Supplies. To ensure compatibility, the VDD_IO and VDD_CORE supplies of the AD1895 and AD1896 must be
set to 3.3 V, while the VIO and VDD supplies of the SRC4190 must be set to 3.3 V.
Pin 1 connection. For the AD1895, pin 1 is a no connect (NC) pin. For the SRC4190, pin 1 functions as the low
group delay selection input and should not be left unconnected. Pin 1 must be connected to either digital ground
or the VIO supply, dependent upon the desired group delay.
Crystal Oscillator. The SRC4190 does not have an on-chip crystal oscillator. An external reference clock is
required at the RCKI input (pin 2).
Reference Clock Frequency. The reference clock input frequency for the SRC4190 must be no higher than
30 MHz, in order to match the master clock frequency specification of the AD1895 and AD1896. In addition, the
SRC4190 does not support the 768fS reference clock rate.
Master Mode Maximum Sampling Frequency. When the input or output ports are set to Master mode, the
maximum sampling frequency must be limited to 96 kHz in order to support the AD1895 and AD1896
specification. This is despite the fact that the SRC4190 supports a maximum sampling frequency of 212 kHz in
Master mode. The user should consider building an option into the design to support the higher sampling
frequency of the SRC4190.
Matched Phase Mode. Due to the internal architecture of the SRC4190, it does not require or support the
matched phase mode of the AD1896. Given multiple SRC4190 devices, if all reference clock (RCKI) inputs are
driven from the same clock source, the devices will be phase matched.
26
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): SRC4190-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
27-Oct-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
SRC4190IDBRQ1
ACTIVE
SSOP
DB
Pins Package Eco Plan (2)
Qty
28
2000 Green (RoHS &
no Sb/Br)
Lead/Ball Finish
CU NIPDAU
MSL Peak Temp (3)
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF SRC4190-Q1 :
• Catalog: SRC4190
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 1
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated