Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 SST32HF802 / 162 / 164MPF (x16) + 1Mb SRAM (x16) ComboMemories Data Sheet FEATURES: • MPF + SRAM ComboMemory – SST32HF802: 512K x16 Flash + 128K x16 SRAM – SST32HF162: 1M x16 Flash + 128K x16 SRAM – SST32HF164: 1M x16 Flash + 256K x16 SRAM • Single 2.7-3.3V Read and Write Operations • Concurrent Operation – Read from or write to SRAM while Erase/Program Flash • Superior Reliability – Endurance: 100,000 Cycles (typical) – Greater than 100 years Data Retention • Low Power Consumption: – Active Current: 15 mA (typical) for Flash or SRAM Read – Standby Current: 20 µA (typical) • Flexible Erase Capability – Uniform 2 KWord sectors – Uniform 32 KWord size blocks • Fast Read Access Times: – Flash: 70 ns and 90 ns – SRAM: 70 ns and 90 ns • Latched Address and Data for Flash • Flash Fast Erase and Word-Program: – Sector-Erase Time: 18 ms (typical) – Block-Erase Time: 18 ms (typical) – Chip-Erase Time: 70 ms (typical) – Word-Program Time: 14 µs (typical) – Chip Rewrite Time: SST32HF802: 8 seconds (typical) SST32HF162/164: 15 seconds (typical) • Flash Automatic Erase and Program Timing – Internal VPP Generation • Flash End-of-Write Detection – Toggle Bit – Data# Polling • CMOS I/O Compatibility • JEDEC Standard Command Set • Package Available – 48-lead TSOP (12mm x 20mm) – 48-ball TBGA (10mm x 12mm) PRODUCT DESCRIPTION bank enable signal, BEF# selects the flash memory bank. The WE# signal has to be used with Software Data Protection (SDP) command sequence when controlling the Erase and Program operations in the flash memory bank. The SDP command sequence protects the data stored in the flash memory bank from accidental alteration. The SST32HF802/162/164 ComboMemory devices integrate a 512K x16 or 1M x16 CMOS flash memory bank with a 128K x16 or 256K x16 CMOS SRAM memory bank in a Multi-Chip Package (MCP), manufactured with SST’s proprietary, high performance SuperFlash technology. Featuring high performance Word-Program, the flash memory bank provides a maximum Word-Program time of 14 µsec. The entire flash memory bank can be erased and programmed word-by-word in typically 8 seconds for the SST32HF802 and 15 seconds for the SST32HF162/164, when using interface features such as Toggle Bit or Data# Polling to indicate the completion of Program operation. To protect against inadvertent flash write, the SST32HF802/ 162/164 devices contain on-chip hardware and software data protection schemes.The SST32HF802/162/164 devices offer a guaranteed endurance of 10,000 cycles. Data retention is rated at greater than 100 years. The SST32HF802/162/164 devices consist of two independent memory banks with respective bank enable signals. The Flash and SRAM memory banks are superimposed in the same memory address space. Both memory banks share common address lines, data lines, WE# and OE#. The memory bank selection is done by memory bank enable signals. The SRAM bank enable signal, BES# selects the SRAM bank. The flash memory ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 520 1 The SST32HF802/162/164 provide the added functionality of being able to simultaneously read from or write to the SRAM bank while erasing or programming in the flash memory bank. The SRAM memory bank can be read or written while the flash memory bank performs SectorErase, Bank-Erase, or Word-Program concurrently. All flash memory Erase and Program operations will automatically latch the input address and data signals and complete the operation in background without further input stimulus requirement. Once the internally controlled erase or program cycle in the flash bank has commenced, the SRAM bank can be accessed for read or write. The SST32HF802/162/164 devices are suited for applications that use both flash memory and SRAM memory to store code or data. For systems requiring low power and small form factor, the SST32HF802/162/164 devices significantly improve performance and reliability, while lowering power consumption, when compared with multiple chip solutions. The SST32HF802/162/164 inherently use less energy during erase and program than alternative flash The SST logo and SuperFlash are registered trademarks of Silicon Storage Technology, Inc. MPF and ComboMemory are trademarks of Silicon Storage Technology, Inc. These specifications are subject to change without notice. Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet SRAM Write technologies. The total energy consumed is a function of the applied voltage, current, and time of application. Since for any given voltage range, the SuperFlash technology uses less current to program and has a shorter erase time, the total energy consumed during any Erase or Program operation is less than alternative flash technologies. The SRAM Write operation of the SST32HF802/162/164 is controlled by WE# and BES# being low for the system to write to the SRAM. During the Word-Write operation, the addresses and data are referenced to the rising edge of WE# or BES#, which ever occurs first. The write time is measured from the last falling edge to the rising edge of WE# or BES#. Refer to the Write cycle timing diagrams, Figures 4 and 5, for further details. The SuperFlash technology provides fixed Erase and Program times, independent of the number of Erase/Program cycles that have occurred. Therefore the system software or hardware does not have to be modified or de-rated as is necessary with alternative flash technologies, whose Erase and Program times increase with accumulated Erase/Program cycles. Flash Operation With BEF# active, the SST32HF162/164 operate as 1M x16 flash memory and the SST32HF802 operates as 512K x16 flash memory. The flash memory bank is read using the common address lines, data lines, WE# and OE#. Erase and Program operations are initiated with the JEDEC standard SDP command sequences. Address and data are latched during the SDP commands and during the internally timed Erase and Program operations. Device Operation The ComboMemory uses BES# and BEF# to control operation of either the SRAM or the flash memory bank. When BES# is low, the SRAM Bank is activated for Read and Write operation. When BEF# is low the flash bank is activated for Read, Program or Erase operation. BES# and BEF# cannot be at low level at the same time. If BES# and BEF# are both asserted to low level bus contention will result and the device may suffer permanent damage. All address, data, and control lines are shared by SRAM Bank and flash bank which minimizes power consumption and loading. The device goes into standby when both bank enables are high. Flash Read The Read operation of the SST32HF802/162/164 devices is controlled by BEF# and OE#. Both have to be low, with WE# high, for the system to obtain data from the outputs. BEF# is used for flash memory bank selection. When BEF# and BES# are high, both banks are deselected and only standby power is consumed. OE# is the output control and is used to gate data from the output pins. The data bus is in high impedance state when OE# is high. Refer to Figure 6 for further details. SRAM Operation With BES# low and BEF# high, the SST32HF802/162 operate as 128K x16 CMOS SRAM, and the SST32HF164 operates as 256K x16 CMOS SRAM, with fully static operation requiring no external clocks or timing strobes. The SST32HF802/162 SRAM is mapped into the first 128 KWord address space of the device, and the SST32HF164 SRAM is mapped into the first 256 KWord address space. When BES# and BEF# are high, both memory banks are deselected and the device enters standby mode. Read and Write cycle times are equal. The control signals UBS# and LBS# provide access to the upper data byte and lower data byte. See Table 3 for SRAM read and write data byte control modes of operation. Flash Erase/Program Operation SDP commands are used to initiate the flash memory bank Program and Erase operations of the SST32HF802/162/ 164. SDP commands are loaded to the flash memory bank using standard microprocessor write sequences. A command is loaded by asserting WE# low while keeping BEF# low and OE# high. The address is latched on the falling edge of WE# or BEF#, whichever occurs last. The data is latched on the rising edge of WE# or BEF#, whichever occurs first. SRAM Read Flash Word-Program Operation The SRAM Read operation of the SST32HF802/162/164 is controlled by OE# and BES#, both have to be low with WE# high for the system to obtain data from the outputs. BES# is used for SRAM bank selection. OE# is the output control and is used to gate data from the output pins. The data bus is in high impedance state when OE# is high. See Figure 3 for the Read cycle timing diagram. The flash memory bank of the SST32HF802/162/164 devices is programmed on a word-by-word basis. Before the Program operations, the memory must be erased first. The Program operation consists of three steps. The first step is the three-byte load sequence for Software Data Protection. The second step is to load word address and word data. During the Word-Program operation, the addresses ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 2 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet are latched on the falling edge of either BEF# or WE#, whichever occurs last. The data is latched on the rising edge of either BEF# or WE#, whichever occurs first. The third step is the internal Program operation which is initiated after the rising edge of the fourth WE# or BEF#, whichever occurs first. The Program operation, once initiated, will be completed, within 20 µs. See Figures 7 and 8 for WE# and BEF# controlled Program operation timing diagrams and Figure 18 for flowcharts. During the Program operation, the only valid flash Read operations are Data# Polling and Toggle Bit. During the internal Program operation, the host is free to perform additional tasks. Any SDP commands loaded during the internal Program operation will be ignored. the only valid read is Toggle Bit or Data# Polling. See Table 4 for the command sequence, Figure 10 for timing diagram, and Figure 21 for the flowchart. Any commands issued during the Chip-Erase operation are ignored. Write Operation Status Detection The SST32HF802/162/164 provide two software means to detect the completion of a write (Program or Erase) cycle, in order to optimize the system write cycle time. The software detection includes two status bits: Data# Polling (DQ7) and Toggle Bit (DQ6). The End-of-Write detection mode is enabled after the rising edge of WE#, which initiates the internal program or erase operation. The actual completion of the nonvolatile write is asynchronous with the system; therefore, either a Data# Polling or Toggle Bit read may be simultaneous with the completion of the Write cycle. If this occurs, the system may possibly get an erroneous result, i.e., valid data may appear to conflict with either DQ7 or DQ6. In order to prevent spurious rejection, if an erroneous result occurs, the software routine should include a loop to read the accessed location an additional two (2) times. If both reads are valid, then the device has completed the write cycle, otherwise the rejection is valid. Flash Sector/Block-Erase Operation The Flash Sector/Block-Erase operation allows the system to erase the device on a sector-by-sector (or block-byblock) basis. The SST32HF802/162/164 offer both SectorErase and Block-Erase mode. The sector architecture is based on uniform sector size of 2 KWord. The Block-Erase mode is based on uniform block size of 32 KWord. The Sector-Erase operation is initiated by executing a six-byte command sequence with Sector-Erase command (30H) and sector address (SA) in the last bus cycle. The address lines A19-A11, for SST32HF162/164, and A18-A11, for SST32HF802, are used to determine the sector address. The Block-Erase operation is initiated by executing a sixbyte command sequence with Block-Erase command (50H) and block address (BA) in the last bus cycle. The address lines A19-A15, for SST32HF162/164, and A18-A15, for SST32HF802, are used to determine the block address. The sector or block address is latched on the falling edge of the sixth WE# pulse, while the command (30H or 50H) is latched on the rising edge of the sixth WE# pulse. The internal Erase operation begins after the sixth WE# pulse. The End-of-Erase operation can be determined using either Data# Polling or Toggle Bit methods. See Figures 12 and 13 for timing waveforms. Any commands issued during the Sector- or Block-Erase operation are ignored. Flash Data# Polling (DQ7) When the SST32HF802/162/164 flash memory banks are in the internal Program operation, any attempt to read DQ7 will produce the complement of the true data. Once the Program operation is completed, DQ7 will produce true data. Note that even though DQ7 may have valid data immediately following the completion of an internal Write operation, the remaining data outputs may still be invalid: valid data on the entire data bus will appear in subsequent successive Read cycles. During internal Erase operation, any attempt to read DQ7 will produce a ‘0’. Once the internal Erase operation is completed, DQ7 will produce a ‘1’. The Data# Polling is valid after the rising edge of the fourth WE# (or BEF#) pulse for Program operation. For Sector- or Block-Erase, the Data# Polling is valid after the rising edge of the sixth WE# (or BEF#) pulse. See Figure 9 for Data# Polling timing diagram and Figure 19 for a flowchart. Flash Chip-Erase Operation The SST32HF802/162/164 provide a Chip-Erase operation, which allows the user to erase the entire memory array to the “1” state. This is useful when the entire device must be quickly erased. Flash Toggle Bit (DQ6) During the internal Program or Erase operation, any consecutive attempts to read DQ6 will produce alternating 1s and 0s, i.e., toggling between 1 and 0. When the internal Program or Erase operation is completed, the toggling will stop. The flash memory bank is then ready for the next operation. The Toggle Bit is valid after the rising edge of the fourth WE# (or BEF#) pulse for Program operation. For The Chip-Erase operation is initiated by executing a sixbyte command sequence with Chip-Erase command (10H) at address 5555H in the last byte sequence. The Erase operation begins with the rising edge of the sixth WE# or CE#, whichever occurs first. During the Erase operation, ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 3 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet Sector- or Bank-Erase, the Toggle Bit is valid after the rising edge of the sixth WE# (or BEF#) pulse. See Figure 10 for Toggle Bit timing diagram and Figure 19 for a flowchart. The device will ignore all SDP commands when an Erase or Program operation is in progress. Note that Product Identification commands use SDP; therefore, these commands will also be ignored while an Erase or Program operation is in progress. Flash Memory Data Protection The SST32HF802/162/164 flash memory bank provides both hardware and software features to protect nonvolatile data from inadvertent writes. Product Identification The product identification mode identifies the devices as the SST32HFxxx and manufacturer as SST. This mode may be accessed by software operations only. The hardware device ID Read operation, which is typically used by programmers, cannot be used on this device because of the shared lines between flash and SRAM in the multi-chip package. Therefore, application of high voltage to pin A9 may damage this device. Users may use the software product identification operation to identify the part (i.e., using the device ID) when using multiple manufacturers in the same socket. For details, see Tables 3 and 4 for software operation, Figure 14 for the software ID entry and read timing diagram and Figure 20 for the ID entry command sequence flowchart. Flash Hardware Data Protection Noise/Glitch Protection: A WE# or BEF# pulse of less than 5 ns will not initiate a Write cycle. VDD Power Up/Down Detection: The Write operation is inhibited when VDD is less than 1.5V. Write Inhibit Mode: Forcing OE# low, BEF# high, or WE# high will inhibit the Flash Write operation. This prevents inadvertent writes during power-up or power-down. Flash Software Data Protection (SDP) The SST32HF802/162/164 provide the JEDEC approved software data protection scheme for all flash memory bank data alteration operations, i.e., Program and Erase. Any Program operation requires the inclusion of a series of three-byte sequence. The three byte-load sequence is used to initiate the Program operation, providing optimal protection from inadvertent Write operations, e.g., during the system power-up or power-down. Any Erase operation requires the inclusion of six-byte load sequence. The SST32HF802/162/164 devices are shipped with the software data protection permanently enabled. See Table 4 for the specific software command codes. During SDP command sequence, invalid SDP commands will abort the device to the read mode, within Read Cycle Time (TRC). TABLE 1: PRODUCT IDENTIFICATION Data 0000H 00BFH SST32HF802 0001H 2781H SST32HF162/164 0001H 2782H Manufacturer’s ID Device ID T1.1 520 Product Identification Mode Exit/Reset In order to return to the standard read mode, the Software Product Identification mode must be exited. Exiting is accomplished by issuing the Exit ID command sequence, which returns the device to the Read operation. Please note that the software-reset command is ignored during an internal Program or Erase operation. See Table 4 for software command codes, Figure 15 for timing waveform and Figure 20 for a flowchart. Concurrent Read and Write Operations The SST32HF802/162/164 provide the unique benefit of being able to read from or write to SRAM, while simultaneously erasing or programming the Flash. This allows data alteration code to be executed from SRAM, while altering the data in Flash. The following table lists all valid states. Design Considerations SST recommends a high frequency 0.1 µF ceramic capacitor to be placed as close as possible between VDD and VSS, e.g., less than 1 cm away from the VDD pin of the device. Additionally, a low frequency 4.7 µF electrolytic capacitor from VDD to VSS should be placed within 1 cm of the VDD pin. CONCURRENT READ/WRITE STATE TABLE Flash Program/Erase Program/Erase Address SRAM Read Write ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 4 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet FUNCTIONAL BLOCK DIAGRAM Address Buffers AMS(1)-A0 UBS# LBS# BES# BEF# OE# WE# SRAM Control Logic Address Buffers & Latches I/O Buffers SuperFlash Memory 520 ILL B1.1 SST32HF162/164 A15 A14 A13 A12 A11 A10 A9 A8 A19 NC WE# VDDS BES# UBS# LBS# A18 A17 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 DQ15 - DQ8 DQ7 - DQ0 SST32HF162/164 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 Standard Pinout Top View Die Up A16 NC VSS DQ15 DQ7 DQ14 DQ6 DQ13 DQ5 DQ12 DQ4 VDDF DQ11 DQ3 DQ10 DQ2 DQ9 DQ1 DQ8 DQ0 OE# VSS BEF# A0 520 ILL F01b.1 FIGURE 1: PIN ASSIGNMENTS FOR 48-LEAD TSOP (12MM ©2001 Silicon Storage Technology, Inc. X 20MM) S71171-05-000 8/01 5 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet TOP VIEW (balls facing down) 5 4 BES# VSS DQ1 A10 DQ5 DQ2 OE# DQ7 DQ4 A1 A4 A2 A0 A7 A3 DQ0 A6 A18 NC NC NC 6 A9 5 A14 4 A15 3 BES# VSS DQ1 A1 A2 A4 A19 A9 A10 DQ5 DQ2 A0 A3 A7 NC A14 OE# DQ7 DQ4 DQ0 A6 A18 NC A15 3 A11 A8 A5 DQ8 DQ3 DQ12 A12 LBS# 2 A11 A8 DQ3 DQ12 A12 LBS# A13 A17 UBS# BEF# DQ10 VDDF DQ6 DQ15 A5 DQ8 2 A17 UBS# BEF# DQ10 VDDF DQ6 DQ15 WE# VDDS A16 VSS DQ9 DQ11 DQ13 DQ14 A B C D E F G H 1 520 ILL F01a.0 A13 1 WE# VDDS A16 VSS DQ9 DQ11 DQ13 DQ14 A B C D E F G H SST32HF802 520 ILL F01.0 6 TOP VIEW (balls facing down) SST32HF162/SST32HF164 FIGURE 2: PIN ASSIGNMENTS FOR 48-BALL TBGA (10MM X 12MM) TABLE 2: PIN DESCRIPTION Symbol Pin Name Functions AMS1-A0 Address Inputs To provide flash addresses: A19-A0 for 16M, and A18-A0 for 8M SRAM addresses: A16-A0 for 2M and A17-A0 for 4M Data Input/output To output data during Read cycles and receive input data during Write cycles. Data is internally latched during a flash Erase/Program cycle. The outputs are in tri-state when OE# or BES# and BEF# are high. SRAM Memory Bank Enable To activate the SRAM memory bank when BES# is low. DQ15-DQ0 BES# BEF# Flash Memory Bank Enable To activate the Flash memory bank when BEF# is low. OE# Output Enable To gate the data output buffers. WE# Write Enable To control the Write operations. VDDF Power Supply (Flash) 2.7-3.3V Power Supply to Flash only. VDDS Power Supply (SRAM) 2.7-3.3V Power Supply to SRAM only (For L3K package, VDDF and VDDS share one pin as VDD.) VSS Ground UBS# Upper Byte Control (SRAM) To enable DQ15-DQ8 LBS# Lower Byte Control (SRAM) To enable DQ7-DQ0 No Connection Unconnected Pins NC T2.2 520 1. AMS=Most significant address ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 6 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet TABLE 3: OPERATION MODES SELECTION Mode BES#1 BEF#1 OE# WE# UBS# LBS# DQ15 to DQ8 DQ7 to DQ0 Address VIL VIL X2 X X X X X X Read VIH VIL VIL VIH X X DOUT DOUT AIN Program VIH VIL VIH VIL X X DIN DIN AIN X VIL VIH VIL X X X X Sector or Block address, XXH for Chip-Erase VIL VIH VIL VIH VIL VIL DOUT DOUT AIN VIL VIH VIL VIH VIL VIH DOUT High Z AIN VIL VIH VIL VIH VIH VIL High Z DOUT AIN Not Allowed Flash Erase SRAM Read Write Standby Flash Write Inhibit Output Disable VIL VIH X VIL VIL VIL DIN DIN AIN VIL VIH X VIL VIL VIH DIN High Z AIN VIL VIH X VIL VIH VIL High Z DIN AIN VIHC VIHC X X X X High Z High Z X X X VIL X X X High Z / DOUT High Z / DOUT X X X X VIH X X High Z / DOUT High Z / DOUT X High Z / DOUT High Z / DOUT X X VIH X X X X VIH VIL VIH VIH X X High Z High Z X VIL VIH X X VIH VIH High Z High Z X VIL VIH VIH VIH X X High Z High Z X VIH VIL VIL VIH X X Product Identification Software Mode Manufacturer’s ID (00BFH) Device ID3 A19-A1=VIL, A0=VIH (See Table 4) T3.2 520 1. Do not apply BES#=VIL and BEF#=VIL at the same time 2. X can be VIL or VIH, but no other value. 3. Device ID 2781H for SST32HF802, 2782H for SST32HF162/164 ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 7 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet TABLE 4: SOFTWARE COMMAND SEQUENCE Command Sequence 1st Bus Write Cycle 2nd Bus Write Cycle 3rd Bus Write Cycle 4th Bus Write Cycle Addr1 Data2 Addr1 Data2 Addr1 Data2 Addr1 Data2 Word-Program 5555H AAH 2AAAH 55H 5555H A0H WA3 Data Sector-Erase 5555H AAH 2AAAH 55H 5555H 80H 5555H AAH 5th Bus Write Cycle 6th Bus Write Cycle Addr1 Data2 Addr1 Data2 2AAAH 55H SAX4 30H 50H 10H Block-Erase 5555H AAH 2AAAH 55H 5555H 80H 5555H AAH 2AAAH 55H BAX4 Chip-Erase 5555H AAH 2AAAH 55H 5555H 80H 5555H AAH 2AAAH 55H 5555H 2AAAH 55H 5555H 90H 2AAAH 55H 5555H F0H Software ID Entry5,6 5555H AAH Software ID Exit XXH F0H Software ID Exit 5555H AAH T4.2 520 1. 2. 3. 4. Address format A14-A0 (Hex),Address A15 can be VIL or VIH, but no other value, for the Command sequence. DQ15-DQ8 can be VIL or VIH, but no other value, for the Command sequence. WA = Program word address SAX for Sector-Erase; uses AMS-A11 address lines BAX, for Block-Erase; uses A19-A15 address lines AMS = Most significant address AMS = A18 for SST32HF802 and A19 for SST32HF162/164 5. The device does not remain in Software Product ID Mode if powered down. 6. With AMS-A1 =0; SST Manufacturer’s ID= 00BFH, is read with A0=0, SST32HF802 Device ID = 2781H, is read with A0=1. SST32HF162/164 Device ID = 2782H, is read with A0=1. Absolute Maximum Stress Ratings (Applied conditions greater than those listed under “Absolute Maximum Stress Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these conditions or conditions greater than those defined in the operational sections of this data sheet is not implied. Exposure to absolute maximum stress rating conditions may affect device reliability.) Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20°C to +85°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to +150°C D. C. Voltage on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.5V to VDD1+0.3V Transient Voltage (<20 ns) on Any Pin to Ground Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to VDD1+1.0V Package Power Dissipation Capability (Ta = 25°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0W Surface Mount Lead Soldering Temperature (3 Seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240°C Output Short Circuit Current2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA 1. VDD = VDDF and VDDS 2. Outputs shorted for no more than one second. No more than one output shorted at a time. OPERATING RANGE Range Commercial Extended AC CONDITIONS OF Ambient Temp VDD 0°C to +70°C 2.7-3.3V -20°C to +85°C 2.7-3.3V TEST Input Rise/Fall Time . . . . . . . . . . . . . . 5 ns Output Load . . . . . . . . . . . . . . . . . . . . CL = 30 pF See Figures 16 and 17 ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 8 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet TABLE 5: DC OPERATING CHARACTERISTICS (VDD = VDDF AND VDDS = 2.7-3.3V) Limits Symbol Parameter IDD Power Supply Current Min Max Units Test Conditions Address input = VIL/VIH, at f=1/TRC Min, VDD=VDD Max, all DQs open Read Flash 20 SRAM mA OE#=VIL, WE#=VIH BEF#=VIL, BES#=VIH 20 mA BEF#=VIH, BES#=VIL Concurrent Operation 45 mA BEF#=VIH, BES#=VIL Write Flash 25 mA WE#=VIL BEF#=VIL, BES#=VIH, OE#=VIH 20 mA BEF#=VIH, BES#=VIL SRAM ISB Standby VDD Current 3.0V 3.3V 40 75 µA VDD = VDD Max, BEF#=BES#=VIHC ILI Input Leakage Current 1 µA VIN=GND to VDD, VDD=VDD Max 1 µA VOUT=GND to VDD, VDD=VDD Max 0.8 V VDD=VDD Min ILO Output Leakage Current VIL Input Low Voltage VIH Input High Voltage 0.7VDD V VDD=VDD Max VIHC Input High Voltage (CMOS) VDD-0.3 V VDD=VDD Max VOL Flash Output Low Voltage VOH Flash Output High Voltage VOLS SRAM Output Low Voltage VOHS SRAM Output High Voltage 0.2 VDD-0.2 0.4 2.2 V IOL=100 µA, VDD=VDD Min V IOH=-100 µA, VDD=VDD Min V IOL=1 mA, VDD=VDD Min V IOH=-500 µA, VDD=VDD Min T5.5 520 TABLE 6: RECOMMENDED SYSTEM POWER-UP TIMINGS Symbol TPU-READ Parameter 1 TPU-WRITE1 Minimum Units Power-up to Read Operation 100 µs Power-up to Program/Erase Operation 100 µs T6.0 520 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. TABLE 7: CAPACITANCE (Ta = 25°C, f=1 Mhz, other pins open) Parameter Description Test Condition Maximum CI/O1 I/O Pin Capacitance VI/O = 0V 12 pF Input Capacitance VIN = 0V 12 pF CIN 1 T7.0 520 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. TABLE 8: FLASH RELIABILITY CHARACTERISTICS Symbol Parameter Minimum Specification Units Test Method NEND1 Endurance 10,000 Cycles JEDEC Standard A117 TDR1 Data Retention 100 Years JEDEC Standard A103 ILTH1 Latch Up 100 + IDD mA JEDEC Standard 78 T8.1 520 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 9 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet AC CHARACTERISTICS TABLE 9: SRAM READ CYCLE TIMING PARAMETERS SST32HF802/162/164-70 SST32HF802/162/164-90 Symbol Parameter TRCS Read Cycle Time TAAS Address Access Time 70 90 ns TBES Bank Enable Access Time 70 90 ns TOES Output Enable Access Time 35 45 ns TBYES UBS#, LBS# Access Time TBLZS1 BES# to Active Output 0 0 ns Output Enable to Active Output 0 0 ns UBS#, LBS# to Active Output 0 0 ns TOLZS1 TBYLZS TBHZS 1 1 Min Output Disable to High-Z Output TBYHZS1 UBS#, LBS# to High-Z Output TOHS Output Hold from Address Change Min 25 0 35 10 Units ns 90 25 0 Max 90 70 BES# to High-Z Output TOHZS1 Max 70 ns 35 ns 35 ns 45 10 ns ns T9.1 520 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. TABLE 10: SRAM WRITE CYCLE TIMING PARAMETERS SST32HF802/162/164-70 SST32HF802/162/164-90 Symbol Parameter Min Max Min Max TWCS Write Cycle Time 70 90 ns TBWS Bank Enable to End-of-Write 60 80 ns TAWS Address Valid to End-of-Write 60 80 ns TASTS Address Set-up Time 0 0 ns TWPS Write Pulse Width 60 80 ns TWRS Write Recovery Time 0 0 ns TBYWS UBS#, LBS# to End-of-Write 60 TODWS Output Disable from WE# Low TOEWS Output Enable from WE# High 0 0 ns TDSS Data Set-up Time 30 40 ns TDHS Data Hold from Write Time 0 0 80 30 Units ns 40 ns ns T10.1 520 ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 10 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet TABLE 11: FLASH READ CYCLE TIMING PARAMETERS SST32HF802/162/164-70 SST32HF802/162/164-90 Symbol Parameter TRC Read Cycle Time Min Max TBE Bank Enable Access Time 70 90 ns TAA Address Access Time 70 90 ns TOE Output Enable Access Time 35 45 ns TBLZ1 TOLZ1 TBHZ1 TOHZ1 TOH1 BEF# Low to Active Output 0 OE# Low to Active Output 0 70 Min Max 90 ns 0 ns 0 BEF# High to High-Z Output ns 20 OE# High to High-Z Output 20 Output Hold from Address Change 0 Units 30 ns 30 ns 0 ns T11.1 520 1. This parameter is measured only for initial qualification and after a design or process change that could affect this parameter. TABLE 12: FLASH PROGRAM/ERASE CYCLE TIMING PARAMETERS Symbol Parameter TBP Word-Program Time Min Max Units 20 µs TAS Address Setup Time 0 ns TAH Address Hold Time 30 ns TBS WE# and BEF# Setup Time 0 ns TBH WE# and BEF# Hold Time 0 ns TOES OE# High Setup Time 0 ns TOEH OE# High Hold Time 10 ns TBPW BEF# Pulse Width 40 ns TWP WE# Pulse Width 40 ns TWPH WE# Pulse Width High 30 ns TBPH BEF# Pulse Width High 30 ns TDS Data Setup Time 30 ns TDH Data Hold Time 0 ns TIDA Software ID Access and Exit Time 150 ns TSE Sector-Erase 25 ms TBE Block-Erase 25 ms TSCE Chip-Erase 100 ms T12.0 520 ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 11 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet TRCS ADDRESSES AMSS-0 TOHS TAAS TBES BES# TBLZS TBHZS TOES OE# TOLZS TOHZS TBYES UBS#, LBS# TBYLZS TBYHZS DATA VALID DQ15-0 520 ILL F21.0 Note: WE# remains High (VIH) for the Read cycle AMSS = Most Significant SRAM Address FIGURE 3: SRAM READ CYCLE TIMING DIAGRAM TWCS ADDRESSES AMSS-0 TASTS TWPS TWRS WE# TAWS TBWS BES# TBYWS UBS#, LBS# TODWS DQ15-8, DQ7-0 TDSS TOEWS TDHS VALID DATA IN NOTE 2 NOTE 2 520 ILL F27.1 Notes: 1. If OE# is High during the Write cycle, the outputs will remain at high impedance. 2. If BES# goes Low coincident with or after WE# goes Low, the output will remain at high impedance. If BES# goes High coincident with or before WE# goes High, the output will remain at high impedance. Because DIN signals may be in the output state at this time, input signals of reverse polarity must not be applied. FIGURE 4: SRAM WRITE CYCLE TIMING DIAGRAM (WE# CONTROLLED)1 ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 12 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet TWCS ADDRESSES AMSS-0 TWRS TWPS WE# TBWS BES# TAWS TASTS TBYWS UBS#, LBS# TDSS DQ15-8, DQ7-0 NOTE 2 TDHS VALID DATA IN NOTE 2 520 ILL F29.0 Notes: 1. If OE# is High during the Write cycle, the outputs will remain at high impedance. 2. Because DIN signals may be in the output state at this time, input signals of reverse polarity must not be applied. FIGURE 5: SRAM WRITE CYCLE TIMING DIAGRAM (UBS#, LBS# CONTROLLED)1 ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 13 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet TAA TRC ADDRESSES AMSF-0 TBE BEF# TOE OE# TOHZ TOLZ VIH WE# HIGH-Z DQ15-0 TBHZ TOH TBLZ HIGH-Z DATA VALID DATA VALID 520 ILL F18.0 AMSF = Most Significant Flash Address FIGURE 6: FLASH READ CYCLE TIMING DIAGRAM INTERNAL PROGRAM OPERATION STARTS TBP 5555 TAH ADDRESSES AMSF-0 2AAA 5555 ADDR TDH TWP WE# TAS TDS TWPH OE# TCH BEF# TCS DQ15-0 XXAA XX55 XXA0 DATA SW0 SW1 SW2 WORD (ADDR/DATA) AMSF = Most Significant Flash Address X can be VIL or VIH, but no other value 520 ILL F04.1 FIGURE 7: FLASH WE# CONTROLLED PROGRAM CYCLE TIMING DIAGRAM ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 14 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet INTERNAL PROGRAM OPERATION STARTS TBP 5555 TAH ADDRESSES AMSF-0 2AAA 5555 ADDR TDH TCP BEF# TAS TDS TCPH OE# TCH WE# TCS DQ15-0 XXAA XX55 XXA0 DATA SW0 SW1 SW2 WORD (ADDR/DATA) 520 ILL F05.1 AMSF = Most Significant Flash Address X can be VIL or VIH, but no other value FIGURE 8: BEF# CONTROLLED FLASH PROGRAM CYCLE TIMING DIAGRAM ADDRESSES AMSF-0 TCE BEF# TOES TOEH OE# TOE WE# DQ7 Data Data# Data# Data 520 ILL F06.0 AMSF = Most Significant Flash Address FIGURE 9: FLASH DATA# POLLING TIMING DIAGRAM ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 15 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet ADDRESSES AMSF-0 TBE BEF# TOES TOE TOEH OE# WE# DQ6 TWO READ CYCLES WITH SAME OUTPUTS AMSF = Most Significant Flash Address 520 ILL F07.0 FIGURE 10: FLASH TOGGLE BIT TIMING DIAGRAM TSCE SIX-BYTE CODE FOR CHIP-ERASE 5555 ADDRESS AMSF-0 2AAA 5555 5555 2AAA 5555 CE# OE# TWP WE# D15-0 XXAA XX55 XX80 XXAA XX55 XX10 SW0 SW1 SW2 SW3 SW4 SW5 520 ILL F25.2 Note: This device also supports CE# controlled Chip-Erase operation. The WE# and CE# signals are interchageable as long as minmum timings are met. (See Table 12) AMSF = Most Significant Flash Address X can be VIL or VIH, but no other value FIGURE 11: WE# CONTROLLED FLASH CHIP-ERASE TIMING DIAGRAM ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 16 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet TSE SIX-WORD CODE FOR SECTOR-ERASE 5555 ADDRESSES AMSF-0 2AAA 5555 5555 2AAA SAX BEF# OE# TWP WE# DQ15-0 XXAA XX55 SW0 SW1 XX80 XXAA XX55 XX30 SW2 SW3 SW4 SW5 520 ILL F08.2 Note: The device also supports BEF# controlled Sector-Erase operation. The WE# and BEF# signals are interchangeable as long as minimum timings are met. (See Table 12) SAX = Sector Address AMSF = Most Significant Flash Address X can be VIL or VIH, but no other value FIGURE 12: WE# CONTROLLED FLASH SECTOR-ERASE TIMING DIAGRAM TSBE SIX-WORD CODE FOR BLOCK-ERASE 5555 ADDRESSES AMSF-0 2AAA 5555 5555 2AAA BAX BEF# OE# TWP WE# D15-0 Note: XXAA XX55 XX80 XXAA XX55 XX50 SW0 SW1 SW2 SW3 SW4 SW5 520 ILL F17.2 The device also supports BEF# controlled Block-Erase operation. The WE# and BEF# signals are interchangeable as long as minimum timings are met. (See Table 12) BAX = Block Address AMSF = Most Significant Flash Address X can be VIL or VIH, but no other value FIGURE 13: WE# CONTROLLED FLASH BLOCK-ERASE TIMING DIAGRAM ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 17 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet THREE-WORD SEQUENCE FOR SOFTWARE ID ENTRY 5555 ADDRESS A14-0 2AAA 5555 0000 0001 BEF# OE# TIDA TWP WE# TWPH DQ15-0 Note: TAA XXAA XX55 XX90 00BF SW0 SW1 SW2 MFG ID 520 ILL F09.1 Device ID = 2781 for SST32HF802 Device ID = 2782 for SST32HF162/164 X can be VIL or VIH, but no other value. FIGURE 14: SOFTWARE ID ENTRY AND DEVICE ID READ THREE-WORD SEQUENCE FOR SOFTWARE ID EXIT AND RESET 5555 ADDRESS A14-0 DQ15-0 XXAA 2AAA 5555 XX55 XXF0 TIDA BEF# OE# TWP WE# T WHP SW0 SW1 SW2 520 ILL F10.2 Note: X can be VIL or VIH, but no other value. FIGURE 15: SOFTWARE ID EXIT AND RESET ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 18 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet VIHT INPUT VIT REFERENCE POINTS VOT OUTPUT VILT 520 ILL F11.0 AC test inputs are driven at VIHT (0.9 VDD) for a logic “1” and VILT (0.1 VDD) for a logic “0”. Measurement reference points for inputs and outputs are VIT (0.5 VDD) and VOT (0.5 VDD). Input rise and fall times (10% ↔ 90%) are <5 ns. Note: VIT - VINPUT Test VOT - VOUTPUT Test VIHT - VINPUT HIGH Test VILT - VINPUT LOW Test FIGURE 16: AC INPUT/OUTPUT REFERENCE WAVEFORMS TO TESTER TO DUT CL 520 ILL F12.0 FIGURE 17: A TEST LOAD EXAMPLE ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 19 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet Start Write data: XXAAH Address: 5555H Write data: XX55H Address: 2AAAH Write data: XXA0H Address: 5555H Write Word Address/Word Data Wait for end of Program (TBP, Data# Polling bit, or Toggle bit operation) Program Completed 520 ILL F13.3 Note: X can be VIL or VIH, but no other value FIGURE 18: WORD-PROGRAM ALGORITHM ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 20 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet Internal Timer Toggle Bit Data# Polling Program/Erase Initiated Program/Erase Initiated Program/Erase Initiated Read word Read DQ7 Wait TBP, TSCE, or TBE Read same word Program/Erase Completed No Is DQ7 = true data? Yes No Does DQ6 match? Program/Erase Completed Yes Program/Erase Completed 520 ILL F14.0 FIGURE 19: WAIT OPTIONS ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 21 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet Software Product ID Entry Command Sequence Software Product ID Exit & Reset Command Sequence Write data: XXAAH Address: 5555H Write data: XXAAH Address: 5555H Write data: XXF0H Address: XXXXH Write data: XX55H Address: 2AAAH Write data: XX55H Address: 2AAAH Wait TIDA Write data: XX90H Address: 5555H Write data: XXF0H Address: 5555H Return to normal operation Wait TIDA Wait TIDA Read Software ID Return to normal operation 520 ILL F15.2 Note: X can be VIL or VIH, but no other value. FIGURE 20: SOFTWARE PRODUCT COMMAND FLOWCHARTS ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 22 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet Chip-Erase Command Sequence Sector-Erase Command Sequence Block-Erase Command Sequence Load data: XXAAH Address: 5555H Load data: XXAAH Address: 5555H Load data: XXAAH Address: 5555H Load data: XX55H Address: 2AAAH Load data: XX55H Address: 2AAAH Load data: XX55H Address: 2AAAH Load data: XX80H Address: 5555H Load data: XX80H Address: 5555H Load data: XX80H Address: 5555H Load data: XXAAH Address: 5555H Load data: XXAAH Address: 5555H Load data: XXAAH Address: 5555H Load data: XX55H Address: 2AAAH Load data: XX55H Address: 2AAAH Load data: XX55H Address: 2AAAH Load data: XX10H Address: 5555H Load data: XX30H Address: SAX Load data: XX50H Address: BAX Wait TSCE Wait TSE Wait TBE Chip erased to FFFFH Sector erased to FFFFH Block erased to FFFFH 520 ILL F26.2 Note: X can be VIL or VIH, but no other value. FIGURE 21: ERASE COMMAND SEQUENCE ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 23 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet Concurrent Operation Load SDP Command Sequence Flash Program/Erase Initiated Wait for End of Write Indication Read or Write SRAM End Wait Flash Operation Completed End Concurrent Operation 520 ILL F19.0 FIGURE 22: CONCURRENT OPERATION FLOWCHART ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 24 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet PRODUCT ORDERING INFORMATION Device SST32HFxxx Speed - XXX Suffix1 - XX Suffix2 - XX Package Modifier K = 48 leads or balls Package Type E = TSOP (12mm x 20mm) TB = TBGA (10mm x 12mm x 1.2mm) Temperature Range C = Commercial = 0°C to +70°C E = Extended = -20°C to +85°C Minimum Endurance 4 = 10,000 cycles Read Access Speed 70 = 70 ns 90 = 90 ns Density 802 = 8 Mbit Flash + 2 Mbit SRAM 162 = 16 Mbit Flash + 2 Mbit SRAM 164 = 16 Mbit Flash + 4 Mbit SRAM Function Voltage H = 2.7-3.3V Device Family 32 = MPF + SRAM ComboMemory Valid combinations for SST32HF802 SST32HF802-70-4C-EK SST32HF802-70-4C-TBK SST32HF802-70-4E-EK SST32HF802-70-4E-TBK Valid combinations for SST32HF162 SST32HF162-70-4C-EK SST32HF162-70-4C-TBK SST32HF162-70-4E-EK SST32HF162-70-4E-TBK Valid combinations for SST32HF164 SST32HF164-70-4C-EK SST32HF164-90-4C-EK SST32HF164-70-4C-TBK SST32HF164-90-4C-TBK SST32HF164-70-4E-EK SST32HF164-90-4E-EK SST32HF164-70-4E-TBK SST32HF164-90-4E-TBK Note: Valid combinations are those products in mass production or will be in mass production. Consult your SST sales representative to confirm availability of valid combinations and to determine availability of new combinations. ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 25 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet PACKAGING DIAGRAMS 1.05 0.95 Pin # 1 Identifier .50 BSC 12.20 11.80 0.15 0.05 18.50 18.30 0.70 0.50 Note: .270 .170 48-TSOP-EK-ILL.6 20.20 19.80 1. Complies with JEDEC publication 95 MO-142 DD dimensions, although some dimensions may be more stringent. 2. All linear dimensions are in millimeters (min/max). Scale is 1:5 mm. 3. Coplanarity: 0.1 (±.05) mm. 4. Maximum allowable mold flash is 0.15mm at the package ends, and 0.25mm between leads. 48-LEAD THIN SMALL OUTLINE PACKAGE (TSOP) 12MM SST PACKAGE CODE: EK X ©2001 Silicon Storage Technology, Inc. 20MM S71171-05-000 8/01 26 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet BOTTOM VIEW 12.00 ± 0.20 7.0 TOP VIEW 1.0 8 8 7 7 10.00 ± 0.20 6 6 5.0 5 5 4 4 3 3 2 2 1 1 1.0 0.50 ± 0.05 (48X) A1 CORNER H G F E D C B A A B C D E F G H A1 CORNER 1.10 ± 0.10 SIDE VIEW 48ba-TBGA-TBK-10x12-500mic-ILL.5 0.15 SEATING PLANE 1mm 0.40 ± 0.05 Note: 1. Although many dimensions are similar to those of JEDEC Publication 95, MO-210, this specific package is not registered. 2. All linear dimensions are in millimeters (min/max). 3. Coplanarity: 0.1 (±.05) mm. 4. The actual shape of the corners may be slightly different than as portrayed in the drawing. 48-BALL THIN-PROFILE BALL GRID ARRAY (TBGA) 10MM SST PACKAGE CODE: TBK ©2001 Silicon Storage Technology, Inc. X 12MM S71171-05-000 8/01 27 520 Multi-Purpose Flash (MPF) + SRAM ComboMemory SST32HF802 / SST32HF162 / SST32HF164 Data Sheet Silicon Storage Technology, Inc. • 1171 Sonora Court • Sunnyvale, CA 94086 • Telephone 408-735-9110 • Fax 408-735-9036 www.SuperFlash.com or www.ssti.com ©2001 Silicon Storage Technology, Inc. S71171-05-000 8/01 28 520