Data contained in this document may be changed without prior notification. MSD-M3A-8K02-UE RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group Development Board M3A-8K02 Instruction Manual VER.1.0 RENESAS TECHNOLOGY CORPORATION RENESAS SOLUTIONS CORPORATION 2003.07.07 Keep safety first in your circuit designs! * RENESAS TECHNOLOGY CORPORATION puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials These materials are intended as a reference to assist our customers in the selection of the RENESAS semiconductor product best suited to the customer’s application; they do not convey any license under any intellectual property rights, or any other rights, belonging to RENESAS TECHNOLOGY CORPORATION or a third party. RENESAS TECHNOLOGY CORPORATION assumes no responsibility for any damage, or infringement of any third-party’s rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by RENESAS TECHNOLOGY CORPORATION without notice due to product improvements or other reasons. It is therefore recommended that customers contact RENESAS TECHNOLOGY CORPORATION or an authorized RENESAS Semiconductor product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. RENESAS TECHNOLOGY CORPORATION assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by RENESAS TECHNOLOGY CORPORATION by various means, including the RENESAS Semiconductor home page (http://www.renesas.com/eng/). When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. RENESAS TECHNOLOGY CORPORATION assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. RENESAS TECHNOLOGY CORPORATION semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact RENESAS TECHNOLOGY CORPORATION or an authorized RENESAS Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical aerospace, nuclear, or undersea repeater use. The prior written approval of RENESAS TECHNOLOGY CORPORATION is necessary to reprint or reproduce in whole or in part these materials. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. Please contact RENESAS TECHNOLOGY CORPORATION or an authorized RENESAS Semiconductor product distributor for further details on these materials or the products contained therein. Revision History Rev. No. 0.0 1.0 Date 2003/2/1 2003/7/7 38K0/38K2 Group Development Board M3A-8K02 Contents Draft version First Edition of PDF Version * Related Materials RENESAS Microcomputers: 38K0 (38K2) Group Data Sheet * Home page of RENESAS Semiconductors. http://www.renesas.com/en/usb - Index Chapter 1 .................................................................................................................................... 1 M3A-8K02 ................................................................................................................................ 1 1.0 Introduction ..............................................................................................................................................2 1.1 Package Contents....................................................................................................................................3 1.2 Top View....................................................................................................................................................4 1.3 Top Boards G02/G03................................................................................................................................5 1.4 Mounting AD Conversion Capacitors and Oscillators .........................................................................7 1.5 Power Supply ...........................................................................................................................................8 1.6 Switching Vcc Voltage (5V, 3.3V)............................................................................................................9 1.7 USB Function .........................................................................................................................................10 1.8 Keyboard Connection ...........................................................................................................................11 1.9 Jumper Functions..................................................................................................................................12 1.10 Flash Chip Reprogramming (G03) .......................................................................................................13 1.10.1 Serial Reprogramming (Flash Writer) ..................................................................................................14 1.10.2 Flash Over USB Reprogramming (FOUSB) ........................................................................................15 1.11 Peripheral Circuits .................................................................................................................................16 1.12 Components Table.................................................................................................................................18 Chapter 2 .................................................................................................................................. 20 Other Development Boards ................................................................................................. 20 2.1 G02、G03、G04 Options........................................................................................................................21 2.2 M3A-8K10 (COM Class Demo Board) ..................................................................................................21 2.3 M38C29T-64FPD .....................................................................................................................................22 2.4 M38C29T-64LCA.....................................................................................................................................22 Chapter 3 .................................................................................................................................. 23 Development Environment .................................................................................................. 23 3.1 Development Environment Example ...................................................................................................24 Chapter 1 M3A-8K02 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.0 Introduction M3A-8K02 is a development board for the Renesas USB Full-Speed MCU 38K0/38K2 Group (8-bit)Note 1. M3A-8K02 comes with the USB function, USB hub, and many key peripheral circuits enabling faster and more efficient application development. Note 1: 38K0 Group devices come with the USB Function; 38K2 Group devices come with the USB function as well as the USB hub. M3A-8K02 consists of 4 boards: G01/G02/G03/G04. Each board is described in detail below. * G01 This is the main M3A-8K02 board. It provides the USB hub and other peripheral circuits necessary for the development process. * G02 This is the RFS top board (“RFS board” hereon) with built-in sockets for mounting the debugger (M38K09RS/M38K29RFS). G02 is mostly used for program evaluation with the debugger. * G03 This is the Flash Chip (M38K29F8HP) top board (“Flash-chip board” hereon), and is normally used for program verification with flash chips. * G04 This is the external universal board, which enables circuit expansions for G01. This can be used for integrating circuits not included on G01. The M3A-8K02 comes bundled with all four boards. Each board can also be purchased separately under the corresponding part number (M3A-8K02G02/G03/G04). M3A-8K02 -> M3A-8K02 2 G01 (Main Board) G02 (RFS Board) G03 (Flash-chip Board) G04 (External Universal Board) RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.1 Package Contents * M3A-8K02G01 ------------------------------------------------------- 1 board * M3A-8K02G02 ------------------------------------------------------- 1 board * M3A-8K02G03 ------------------------------------------------------- 1 board * M3A-8K02G04 ------------------------------------------------------- 1 board * DC Plug ------------------------------------------------------- 1 piece * Accessories ------------------------------------------------------- 4 pcs. Oscillators ------- 6MHz (1), 12MHz (1) Capacitor ------- 30pF (2) * Instruction Manual (Japanese) * Instruction Manual (English) ------------------------------------------------------- 1 1 3 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.2 Top View Figure 1.2 shows the top view of M3A-8K02 with detailed component names. Power Input & Switch Flash Mode Switch Vcc Switch Boot Mode Set Switch Remote-Wakeup Test Button Power Gate Reset Switch USB Up-Port G04 Connector USB Down-Port 1 OverCurrent Button Port Pins USB Down-Port 2 OverCurrent Button Top Board Connection Sockets Hub Connection Switch Flash Writer Connector Figure 1.2 Top View and Component Names 4 Keyboard Connector OverCurrent Detection Jumper Switch RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.3 Top Boards G02/G03 Top boards G02 and G03 allow the user to perform either debug evaluations or chip testing with a simple switch of a board. Attach G02 (RFS board) to the main board in order to connect a debugger, or attach G03 (Flash-chip board) for chip testing. G02 (RFS board) provides an RFS socket in the center of the board for attachment of the emulation chip for debug evaluations. To perform an evaluation, insert either M38K29RFS or M38K09RFS into the socket and connect the debugger (see Figure 1.3(2)). G03 (Flash-chip board) provides a socket in the center of the board for attachment of M38K29F8HPL for Flash chip operational verification. Because the Flash chip already contains the rewriting control program, the application software can be directly downloaded to the Flash-chip board and operational verification performed (for more details concerning Flash-chip reprogramming, see “1.11 Flash-Chip Reprogramming”). M38K29F8HPL can also run 38K0 application software. Emulation Chip Socket (38K2)Flash Chip (38K2) rewriting control program Figure 1.3(1) Top Views of G02 and G03 5 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 Debugger Cable Emulation Chip Figure 1.3(2) G02 and Debugger Connection 6 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.4 Mounting AD Conversion Capacitors and Oscillators The capacitor pattern for 38K0/38K2 AD conversion is located on the upper left side of both G02 and G03 (1). To evaluate AD conversion, mount 0.1uF chip capacitors (size “1608”) here. The 38K0/38K2 oscillator sockets are located on the left side of both G02 and G03 (2). Insert the bundled oscillator (6MHz or 12MHz, as required)(Note 1) , and a 30pF oscillator capacitor. Note 1: The margin of error for the USB Full-speed data rate is 0.25% (2,500ppm) at 12MB/s. Select a crystal oscillator that can guarantee the same. 1.Capacitor Mounting Pattern When evaluating AD conversion, insert 0.1uF chip capacitors. 2. Oscillation Circuits Insert 6MHz or 12Mhz crystal oscillator here, in accordance with user program. Figure 1.4 Oscillator and Capacitor Mounting Patterns 7 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.5 Power Supply M3A-8K02 can run on either self-power (external supply of 5V) or bus-power (VBUS power from USB up-port). * Self-Power To run M3A-8K02 on self-power, connect the external supply through TP1 (1) or the DC jack (2), as shown in Figure 1.5. The polarity of the DC jack is “GND” internally and “+” externally. + GND The SELF-POWER switch (S2 in 3) turns the self-power ON/OFF. When switched to ON, the SELF-POWER lamp (LED1 in 4) goes on, and voltage is supplied to the board from the external source (Note 1). In addition, by connecting Jumper PowerINT (JP1 in 5), ON/OFF events can be assigned to the INT0 pin. Note 1: This board is not protected against counter power supply. * Bus-Power If there is no external power supply, the board goes to the bus-power mode and receives power from the USB. If the board is connected to a PC without external power supply, the USB-POWER lamp (LED4 in 6) will go on and power will be supplied via the USB VBUS. * Receiving power from self-power and bus-power ports: If power is supplied from both self-power and bus-power ports, the board will automatically connect to the self-power supply. 3. Self-Power Switch ON/OFF switch for external power supply 1. 5V input port for electrical clips Pin for external power supply connection 5. Connection to INT0 Assigns ON/OFF interrupt. 2. DC Jack Jack for external supply connection + power GND 4. SELF-POWER Lamp Turns on when external power is ON. 6. BUS-POWER Lamp Turns on when bus power is in use. Figure 1.5 Power Supply Areas 8 external power event to INTO RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.6 Switching Vcc Voltage (5V, 3.3V) M3A-8K02 has two power lines: 5V and Vcc. The 5V line depends on the operating voltage of the board and the Vcc line depends on the 38K0/38K2 operating voltage. The user must switch the Vcc line between 5V and 3.3V, according to the 38K0/38K2 operating voltage. Select the voltage value with the VCC SELECT Switch (S7 in 1) as shown in Fig. 1.6. Set the Vcc to either 5V (left side) or 3.3V (right side). In the 38K0/38K2 USB sample firmware, processing differs according to the Vcc value. Please confirm the firmware settings before setting the Vcc. Using a board with differing voltage than the firmware for an extended period may result in damage to the chip. 1. Vcc Select Switch Switches Vcc from 3.3V to 5V. Figure 1.6 Vcc (5V, 3.3V) Switch 9 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.7 USB Function This board comes with one USB up-port (1) and two USB down-ports (2). Please review the usage conditions described below before setting each port. To enable detection of the self-power mode (external power supply) on 38K0/38K2, insert a header link to the Power INT jumper (3). The detection signal is assigned to port P50/INT0. To initiate an external remote wake-up interrupt on 38K0/38K2, insert a header link to one of the wake-up jumpers (Wake-up 1 to 3 in 4). The detection signal will be assigned to either P50, P51, or P52, accordingly, and an external interrupt can be generated to 38K0/38K2 using the remote wake-up button (5). * USB Hub Function To use the USB hub, switch both the hub circuit connection switch and the down-port connection switch (6) to ON. This will assign the necessary circuits to the USB hub, and the hub will be enabled for operation. Keep these switches OFF at all other times. To test the generation of an over-current on the down-port of the USB hub, insert a header link to the Current INT jumper (7). The test signal will be assigned to Port P51/CNTR0, and the over-current test button will be enabled (although a real over-current will not be generated). 5. Remote WakeUp test button Press to test remote wake-up function 3. Connection to INT0 Assigns external power ON/OFF event to INTO interrupt. 1. UP 4. Remote WakeUp assigns jumper for test use 8. OverCurrent test button Press to test over-current generation on down-port 2. DP1 6. Hub Circuit Connection Switch Turn all ON when using 38K2. 2. DP2 Figure 1.7 USB Peripheral Circuits Setup Areas 10 7. Current Output Jumper 51/CNTR0 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.8 Keyboard Connection M3A-8K02 has a built-in keyboard connector. Pins P00-P07, P10-P13, P24-P27, P30-P37, and P53-P57 are assigned to the keyboard connection. Figure 1.8 shows the pin configuration for the connector. USB hub keyboard firmware is available separately. 2 40 1 39 Pin Configuration P07 P06 P05 P04 P03 P02 P01 P00 P10 P37 P36 P35 P34 P33 P32 P31 P30 P57 P56 P55 P54 P53 P27 P26 P25 P24 P13 P12 P11 1. Keyboard Connector 40 38 36 34 33 32 30 28 2 Vcc CN10 Keyboard Scan 39 18 GND GND Return7 Return6 Return5 Return4 Return3 Return2 Return1 Return0 31 29 27 25 23 21 19 17 15 13 11 9 7 6 5 4 3 1 scan17 scan16 scan15 scan14 scan13 scan12 scan11 scan10 scan9 scan8 scan7 scan6 scan5 scan4 scan3 scan2 scan1 scan0 N.C N.C N.C N.C N.C N.C N.C N.C 37 35 26 24 22 20 16 14 Scroll Lock(LED) Caps Lock(LED) Num Lock(LED) 12 10 8 VCC Figure 1.8 Connection Diagram for Keyboard Connector 11 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.9 Jumper Functions As described previously, the jumpers equipped on this board can be set for specific functions. Table 1.9 shows the jumper number and corresponding function. Table 1.9 Jumper Number and Function JP No. JP1(1) Name PowerINT JP2(2) P50 WakeUp P51 WakeUp P52 WakeUp PowerGate Connected to G04 Vcc OverCurrent Assigned to CNTR0 pin for detection signal of down-port over-current JP3(3) JP4(4) JP6(5) JP5(6) Function Assigned to INT0 pin for self-power ON/OFF events Connected to pin P50 of WakeUp switchNote 1 Connected to pin P51 of WakeUp switchNote 2 Connected to pin P52 of WakeUp switch Attached state connected Detached state floating connected floating connected floating connected floating connected connected floating floating Note 1: Do not connect P50 WakeUp (JP2) when PowerINT (JP1) is connected. Note 2: Do not connect P51 WakeUp (JP3) when OverCurrent (JP5) is connected. 2. P50 WakeUp 1. PowerINT 3. P51 WakeUp 4. P52 WakeUp 5. PowerGate Figure 1.9 Jumper Settings 12 6. OverCurrent RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.10 Flash Chip Reprogramming (G03) M3A-8K02 enables the user to reprogram the Flash chip (G03) on board. As M38K29F8HPL, bundled with this board, has been pre-programmed with the Flash rewriting control program, operational verification with the Flash chip can be done immediately after debug. This rewriting control program can be reprogrammed with either serial or USB interfacing: Flashwriter MFW-1 (Sunny Labs) or Flash-Over-USB (FOUSB). As shown in Figure 1.10, the Flash rewriting control program can be selected using the BOOT-MODE switch (S10 in 2) Table 1.10 shows the setup conditions for the BOOT-MODE switch. By setting the FLASH switch (S9 in 1) to ON and supplying power to the board (Note 2), the FLASH lamp (LED5 in 3) will go on and 38K0/38K2 will be in the Flash reprogramming mode. However, if the board Vcc is different than the firmware voltage when processing the Flash rewriting control program, the chip may be damaged. Make sure the VCC-SELECT switch (S7) is set to the same voltage as the firmware. Finally, make sure the oscillator is compatible with the system as well. Note 1: Do not set the BOOT-MODE switches while power is being supplied to the board. Table 1.10 Selecting Flash Rewriting Control Program with BOOT-MODE Switches P26 P27 * * * H H L L L *: Either setting P42 H L L L P16 H H H H Vcc 5V 3.3V 5V 5V Mode Serial Mode (use Flash writer) FOUSB 3V/6MHz FOUSB 5V/12MHz FOUSB 5V/6MHz 3. FLASH Lamp 1. FLASH Switch 2. BOOT-MODE Switches Figure 1.10 Selecting the Flash Program 13 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.10.1 Serial Reprogramming (Flash Writer) The M3A-8K02 board allows the user to reprogram the 38K0/38K2 Flash chip on board (serial reprogramming of F/W) using a flash writer. To perform serial reprogramming, insert the flash writer cable in the flash writer connecter (1), set the VCC-SELECT switch (S7) to 5V, the BOOT-MODE switch (S10 in 2) to P42 = “H” and P16 = “H”, the FLASH switch (S9 in 3) to ON, and then apply external power (or USB up-port VBUS power). Follow instructions for the Flash writer to continue with the reprogramming process. Note 1: Multi-Flashwriter = MFW-1 (Sunny Labs) Note 2: A separate flash writer and reprogramming adapter is necessary for parallel programming new firmware in the 38K0/38K2 boot ROM area. 4. FLASH Lamp 3. FLASH Switch 1. FLASH Writer Connector Figure 1.10.1 Serial Reprogramming 14 2. BOOT-MODE Switch RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.10.2 Flash Over USB Reprogramming (FOUSB) M3A-8K02 enables “Flash Over USB” on-board programming of 38K0/38K2 Flash chips using the USB function. To perform FOUSB (always make sure external power supply is disconnected), set the VCC-SELECT switch (S7) and the BOOT-MODE switch appropriately, set the FLASH switch (S9) to ON, and then connect the up-port to your computer. The FLASH lamp (4) will go on and the host will recognize operations with “RENESAS Flash-Over USB.” After the host PC is connected, run the application program bundled with the M3A-8K02 on the PC and follow the instructions for reprogramming the application firmware. Note: This screen appears in versions 2.00. Screens may differ slightly between product versions. Figure 1.10.2 Flash Over USB Reprogramming for 38K0/38K2 Flash chips 15 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.11 Peripheral Circuits Additional external circuits can be used with the main board via the external universal board (G04 in 1). * Power Supply Power is supplied to external universal board G04 from the main board (G01) or an external source. When using an external power source, connect the source to power supply input pin TP9 (2). When supplying power from the main board, connect G04 to the main board through the JP6 POWERGATE (3) (make sure nothing is connected to JP6 on G01 before connecting the external source to TP9). After making the appropriate connection, set the power supply switch (S2 in 4) on G04 to ON. LED1 will light up and external power or Vcc from G01 will be supplied to Vcc pins TP10, TP11, TP12, and TP13. * System RESET Pin The main board RESET signal can be used for the external universal board as well. To reset external circuits in the same manner as 38K0/38K2, use RESET pin TP8 (5). 3. PowerGate 4. Power Switch 2. Power Input Pin 5. RESET Pin 1. External Universal Board G04 Figure 1.11(1) External Universal Board G04 16 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 P00 P01 P02 P03 P10 P11 P12 P13 P20 P21 P22 P23 P30 P31 P32 P33 P40 P41 P42 P43 P50 P51 P52 P53 P60 P61 P62 P63 GND GND RESET P04 P05 P06 P07 P14 P15 P16 P17 P24 P25 P26 P27 P34 P35 P36 P37 P54 P55 P56 P57 GND GND Figure 1.11(2) Board Pin Numbers 17 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 1.12 Components Table Table 1.12 shows the various components of the M3A-8K02 main board G01 (the same information applies to G02, G03, and G04). Note that the components listed here are not guaranteed for operation in the users’ system. * Please confirm the correct component symbol in the schematics and on the board itself. Table 1.12 Main Board G01 Components Component Name IC1, IC3, IC7, IC10 IC2 Spec. Component No. Maker (Schematic No., Prod. Spec.) FY4ADJ-03A Renesas RK4936 Rohm USBOVer-current protection IC IC4 MIC2026-2BM Micrel 1 Analog Switch IC5 MAX4644EUT-T Maxim 1 AND Logic RESET IC Regulator USB Up-port Connector IC11 IC6 IC8 IC9 CN1 CN2, CN3 MAX394CWP TC7SH08FU PST9140N RN5RT33A UBB-4R-D14T-1 UBA-4R-D14T-1 Toshiba Mitsumi RICOH JST 1 1 1 1 1 2 4.0V reset 3.3V (150mA) OMRON 1 64 pins Name MOS FET Symbol Qty per set 4 1 Notes 2 p-ch included 2 n-ch included 1pc. 4 pcs. Option Board Connector MFW1Connector Top board socket pin Keyboard Connector CN4 XC5F-6432-2 CN5 CN6-CN9 CN10 MAC8 OMRON 1 8 1 10 pins 8 coupled 40 pins Electrolyte Capacitor C1 Nichicon 1 10uF (16V withstand) 2 220uF (16V withstand) Murata Works 10 Rohm 9 0.1uF (precision unspecified) 300, 1/16W or greater (precision unspecified) Chip Capacitor BC1-BC10 XG4A-1031 MF-3-1 XG4A-4031 UUT1C100MCR1G S UWT1C221MCR1G S GRM40F104Z50 Chip Resistor R1, R3, R4, R15, R29-R33 MCR10EZHJ301 C2, C3 R2, R8-R10, R12, R25-R28 R5-R7 R11 R13, R14, R16-R19 R21-R24 R20, MCR10EZHJ104 Ferrite Beads FB1-FB6 LED LED1, LED4 (green) LED2, LED3 (red) LED5 (yellow) LED6-LED9 (orange) S1, S3, S10 S2 S7, S9 S4 S5, S6 MCR10EZHJ103 MCR10EZHJ152 MCR10EZHF33R0 MCR10EZHJ153 BLM21PG221SN1 D GL3KG8 GL3HD8 GL3HY8 GL3HS8 KSD04 AS-12AP AS-22AP SKHMPWE010 SKHMPSE010 S8 SKHMPUE010 J1 MJ-25N1 Chip Resistor Switch DC Socket DC Lamp Lapping Pin Jumper Socket Check Pin Check Pin 18 MP-121WH JP1-JP6 JP1, JP3, JP5, JP6 TP1, TP2 TP5, TP12, TP16, TP24, TP27, TP30, TP33, P00-P07 P10-P17 TP4, TP8, TP9, TP13, TP25, FFC-6BSM1B JS-1 ST-1-1 10 100k(precision unspecified) Murata Works 3 1 6 4 10k(precision unspecified) 1.5k(precision unspecified) 33+-1% 15k(precision unspecified) Sharp 6 Rohm OTAX Nikkai Kaiheiki Alps Marushin Musen Honda Tsushin Kogyo MAC8 2 2 1 4 3 1 2 1 2 forward voltage 2.1V forward voltage 2.0V forward voltage 2.0V forward voltage 2.0V 4-unipolar, single-throw (DIP) unipolar bipolar green brown 1 red 1 1.3mm diameter 1.3mm diameter bundled with board 2 coupled Insert lapping pin 1 6/34 4 2 HK-5-G black 15 Surface mount (black) HK-5-G brown HK-5-G red 8 16 Surface mount (brown) Surface mount (red) RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 Component Name Name Symbol TP28, TP31, TP34, P20-P27 TP26, TP29, TP32, TP35, P30-P37 TP7, TP11, TP15, RXD, TXD, SCLK, SRDY INT0, CNTR0, INT1, P53-P57 P60-P63 TP6, TP10, TP14 TP3 Spacer Spec. Component No. (Schematic No., Prod. Spec.) HK-5-G orange Maker MAC8 Qty per set 12 Notes Surface mount (orange) HK-5-G yellow 7 Surface mount (yellow) HK-5-G green HK-5-G blue HK-5-G gray HK-5-G white AP-13 M3,depth - 6mm 8 4 3 1 4 4 Surface mount (green) Surface mount (blue) Surface mount (gray) Surface mount (white) 13mm long * USB Connector (JST Mfg Co., Ltd.) meets the USB 2.0 compliance test. 19 Chapter 2 Other Development Boards RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 2.1 G02,G03,G04 Options G02/G03/G04 can also be purchased separately. Please order using the corresponding product number: M3A-8K02G02, M3A-8K02G03, or M3A-8K02G04. G02 G03 G04 Figure 2.1 G02, G03, G04 Options 2.2 M3A-8K10 (COM Class Demo Board) M3A-8K10G01, a COM Class demonstration board, is also available for the 38K0 Group. Please contact your local representative for more details. Figure 2.2 COM Class Demo Board M3A-8K10G01 21 RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 2.3 M38C29T-64FPD M38C29T-64FPD is a package conversion board for connecting the emulation chip to the HP package foot pattern (64P6Q-A). Use this board when the emulation chip 100-pin socket (100P6S_A) foot pattern does not fit the trial board. 100-pin RFS-type Emulator MCU -> 64-pin 0.55mm pitch LQFP (HP package) Figure 2.3 M38C29T-64FPD 2.4 M38C29T-64LCA M38C29T-64LCA is a package conversion board for connecting the emulation chip to the FP package foot pattern (64P6U-A). Use this board when the emulation chip 100-pin socket (100P6S_A) foot pattern does not fit the trial board. When using this conversion board, you will also need to purchase 64-pin socket IC61-0644-052 or IC61-0644-053 for the system board. (Note1) Note 1: The 64-pin socket foot pattern is slightly bigger than the FP package foot pattern. 100-pin RFS-type Emulator MCU -> 64-pin 0.8mm pitch LQFP (FP package) Figure 2.4 M38C29T-64LCA 22 Chapter 3 Development Environment RENESAS USB Full-Speed Microcomputers 38K0/38K2 Group M3A-8K02 3.1 Development Environment Example Table 3.1 shows the types of tools required for the firmware development environment of the M38K0/38K2 Group. Table 3.1 Development Environment Example Host Machine Emulator Emulator Debugger Emulator Pod Emulation Chip Target Board Product Number PC/AT compatible (with LPT parallel, USB interface) PC4701U PD38 M38000TL2-FPD M38K09RFS,M38K29RFS M3A-8K02 Emulator Emulation Board Host Machine Emulation Chip Target Board Figure 3.1 Development Environment Example 24 RENESAS USB Full-Speed Microcomputer 38K0/38K2 Group Development Board M3A-8K02 Instruction Manual VER.1.0 RENESAS TECHNOLOGY CORPORATION. RENESAS SOLUTIONS CORPORATION. No unauthorized copy, please. Any contents (including charts) are not allowed for reprinting without contact to RTC. Copyright(C) 2003 RENESAS TECHNOLOGY CORPORATION and RENESAS SOLUTIONS CORPORATION. 1 2 3 4 5 Signal GND Power GND 1 7,8 TP2 POWER GND 5,6 3 4 2 1 1 1 1 P60 P61 P62 P63 P60 P61 P62 P63 IC1 FY4DJ-03A TP1 5V IN VCC VCC VCC VCC 4 3 2 1 R1 300 R2 100k R3 300 R4 300 R5 10k S1 HUB Curr Junc R6 10k LED1 3 2 TP3 RESET RESET To CNVss To 5V 3 1 SELF-POWER LED3 IC2-2 RK4936 4 1 LED2 1 3 S2 P17 P16 P15 P14 P13 P12 P11 P10 5 6 7 8 5,6 J1 DC5V IN BC1 0.1uF P17 P16 P15 P14 P13 P12 P11 P10 R7 10k IC3 FY4DJ-03A IC4 MIC2026-2BM 1 1 R10 100K 5 P17 P16 P15 P14 P13 P12 3 1 1 1 TP8 USBVref R13 27 D0+ D0P20 P21 P22 P23 R14 27 R15 300 3 R16 R17 R18 R19 1 LED4 1 2 3 4 27 27 27 27 1 D- 2 D+ 3 GND 4 4 3.4 3.4 1 2 5 1 JP4 P52 WakeUp 1 OvCur DP1 S5 OvCur DP2 S6 4 IC6 TC7SH08FU + C3 1 R23 15k R24 15k 220uF M3A-8K02G01 RENESAS SOLUTIONS Corp. BC5 0.1uF JP5 OverCurrent INT Title P20 P21 P22 P23 FB6 BLM21PG221SN1D 2 WakeUp SW 1,2 GND 0.1uF 1,2 3 P17/DQ7/AN7 P16/DQ6/AN6 P15/DQ5/AN5 P14/DQ4/AN4 P13/DQ3/AN3 P12/DQ2/AN2 BC4 220uF 4 2 D+ RESET CNVss 1 S4 + C2 3 D- 5 4 VBUS Vref JP3 P51 WakeUp VCC 1 R21 15k R20 100k JP2 P50 WakeUp INT0 TP13 VBUS TP14 R22 D2TP15 15k D2+ TP16 GND FB5 BLM21PG221SN1D 1 VccE VCC JP1 Power INT FB4 BLM21PG221SN1D 5 CN3 USB DP2 P07/KI7 P06/KI6 3 P20 P21 P22 P23 VBUS P24 P25 P43 P42 P41 P40 S3 P2 Junc 1 FB3 BLM21PG221SN1D 8 7 6 5 D1D1+ D2D2+ P43/ExA1/SRDY P42/ExTC/SCLK P41/ExDACK/TxD P40/ExDREQ/RxD 1 CN2 USB DP1 USB Vref TrON D0+ D0P20/D1P21/D1+ P22/D2P23/D2+ D0+ D0D1D1+ D2D2+ P24 P25 TP9 VBUS TP10 D1TP11 D1+ TP12 GND 1 5 FB2 BLM21PG221SN1D Vss 38K0/38K2 P37 P36 P35 P34 P33 P32 P31 P30 1,2 4 PVcc DVcc R12 100k P11 P10 3.4 GND VCC VCC 4 NC 2 P11/DQ1/AN1 P10/DQ0/AN0 P37/ExA0 P36/ExRD P35/ExWR P34/ExCS P33/ExINT P32 P31 P30 3 P00 P01 P02 P03 P04 P05 P06 P07 2 COM P53 P54 P55 P56 P57 D- R11 1.5K P50 P51 P52 3 TP7 D0+ P24 P25 P26 P27 D+ P61(LED1) P62(LED2) P63(LED3) PVss 6 NO 1 1 1 FB1 BLM21PG221SN1D TP6 D0- IN GND V+ 2 TP4 TP5 VBUS GND VBUS 1 2 7,8 IC2-1 RK4936 CN1 USB UpPort 2 P00/KI0 P01/KI1 P02/KI2 P03/KI3 P04/KI4 P05/KI5 R9 100k INT0 FLGB FLGA IN OUTA ENA BC3 5V 0.1uF IC5 MAX4644EUT-T 7 8 P53 P54 P55 P56 P57 BC2 0.1uF VCC VCC 3 Vcc GND + C1 10uF VCC 4 ENB P50/INT0 P51/CNTR0 P52/INT1 R8 100k 2 OUTB 6 3 4 2 1 5 P60(LED0) CNVss2 5,6 P26 P27 7,8 P24 P25 P26 P27 VCC 4 M3A-8K02 G01 Size A3 Document Number Date: Monday, September 29, 2003 Rev DW30146 (1/3) Sheet 5 1 of 3 1 2 3 4 5 5V IC7 FY4DJ-03A VCC 7,8 S7 VCC-SELECT R25 100k 4 USB Vref BC7 0.1uF 2 1 5V IC9 3.3VRegulator/RN5RT VDD VOUT IC10 FY4DJ-03A 3 7,8 5,6 4 1 5 2 1 CE 2 NC 1,2 S8 RESET SW 3 4 3.4 SUB R26 100k 3 GND 3 BC6 0.1uF 6 5 RESET To 2 GND IC8 ResetIC PST9140N 5 4 Vcc Vout 1 3 4 VCC 1 2 1 5V 5,6 BC8 0.1uF BC9 0.1uF R27 100k 2 2 5V VCC JP6 POWER GATE 2 1 1 3 4 6 VCC S9 P00 P01 P02 P03 P10 P11 P12 P13 P20 P21 P22 P23 P30 P31 P32 P33 4 3 2 1 2 5 FLASH 5V S10 BOOT-MODE N.C NO1 NO2 NO3 NO4 4 7 14 17 P40 P41 P43 VCC R30 300 R31 300 R32 300 R33 300 LED6 LED7 LED8 LED9 6 NC1 NC2 NC3 NC4 R28 100k 2 9 12 19 RESET To 15 16 COM1 COM2 COM3 COM4 5 0.1uF 1 2 3 4 5 6 7 8 9 10 3 8 13 18 V- LED5 P16 P42 P27 P26 IN1 IN2 IN3 IN4 GND R29 300 V+ 1 10 11 20 CNVss To 3 5 6 7 8 BC10 IC11 MAX394CWP P50 P51 P52 P53 P60 P61 P62 P63 CN4 HEADER 32X2 1b 1a 2b 1b 2a 3b 2b 3a 4b 3b 4b 4a 5b 5a 6b 5b 6a 7b 6b 7a 8b 7b 8b 8a 9b 9b 9a 10b 10b 10a 11b 12b 11b 11a 13b 12b 12a 14b 13b 13a 15b 14b 14a 16b 15b 15a 17b 16b 16a 18b 17b 17a 19b 18b 18a 19b 19a 20b 21b 20b 20a 22b 21b 21a 23b 22b 22a 24b 23b 23a 25b 24b 24a 26b 25b 25a 26b 26a 27b 28b 27b 27a 29b 28b 28a 30b 29b 29a 31b 30b 30a 32b 31b 31a 32b 32a 1a 2a 3a 4a 5a 6a 7a 8a 9a 10a 11a 12a 13a 14a 15a 16a 17a 18a 19a 20a 21a 22a 23a 24a 25a 26a 27a 28a 29a 30a 31a 32a RESET To P04 P05 P06 P07 P14 P15 P17 P24 P25 P34 P35 P36 P37 3 P54 P55 P56 P57 CN5 FLASH SERIAL M3A-8K02G01 4 4 RENESAS SOLUTIONS Corp. Title M3A-8K02 G01 1 2 3 4 Size A3 Document Number Rev Date: Monday, September 29, 2003 DW30146 (2/3) Sheet 5 2 of 3 1 2 3 4 5 TP17 1 1 2 3 4 5 6 7 8 TP18 1 2 3 4 5 6 7 8 P10 P11 P12 P13 P14 P15 P16 P17 P00 P01 P02 P03 P04 P05 P06 P07 Vss VccE CNVss P16/DQ6/AN6 P14/DQ4/AN4 P12/DQ2/AN2 P0 P30 P31 P32 P33 P34 P35 P36 P37 16 14 12 10 8 6 4 2 CN6 1 2 3 4 5 6 7 8 TP19 1 2 3 4 5 6 7 8 P20 P21 P22 P23 P24 P25 P26 P27 P10 P11 P12 P13 P14 P15 P16 P17 P1 TP20 15 13 11 9 7 5 3 1 CNVss2 P00 P01 P02 P03 P04 P05 P06 P07 P2 TP21 4 3 2 1 P40 P41 P42 P43 P30 P31 P32 P33 P34 P35 P36 P37 1 P20 P21 P22 P23 P24 P25 P26 P27 TP22 1 2 3 4 5 6 7 8 P50 P51 P52 P53 P54 P55 P56 P57 RxD TxD SCLK SRDY P4 P3 INT0 CNTR0 INT1 P53 P54 P55 P56 P57 P5 2 2 TP23 P60(LED0) Vcc Vref RESET P17/DQ7/AN7 P15/DQ5/AN5 P13/DQ3/AN3 P60 P61 P62 P63 CN7 4 3 2 1 P60 P61 P62 P63 P6 CN8 P11/DQ1/AN1 P37/ExA0 P35/ExWR P33/ExINT P31 P43/ExA1/SRDY P41/ExDACK/TxD P07/KI7 16 14 12 10 8 6 4 2 P10/DQ0/AN0 P36/ExRD P34/ExCS P32 P30 P42/ExTC/SCLK P40/ExDREQ/RxD P06/KI6 15 13 11 9 7 5 3 1 P13 P12 P11 P07 P06 P05 P04 P03 P02 P01 P00 P62(LED2) PVss DVcc TrON D0P21/D1+ P23/D2+ P25 2 4 6 8 10 12 14 16 P27 P51/CNTR0 P53 P55 P57 P01/KI1 P03/KI3 P05/KI5 1 3 5 7 9 11 13 15 P10 P37 P36 P35 P34 P33 P32 P31 P30 P57 P56 P55 P54 P53 P27 P26 P25 P24 P61(LED1) P63(LED3) PVcc USB Vref D0+ P20/D1P22/D2P24 3 5V 2 Vcc Return7 Return6 Return5 Return4 Return3 Return2 Return1 Return0 Keyboard Scan 39 18 TP35 VCC VCC 1 TP34 5V 1 VCC TP33 GND 1 5V TP32 VCC 1 TP31 5V 1 VCC TP30 GND 1 TP29 VCC 1 5V 1 TP28 5V CN10 GND GND scan17 scan16 scan15 scan14 scan13 scan12 scan11 scan10 scan9 scan8 scan7 scan6 scan5 scan4 scan3 scan2 scan1 scan0 37 35 26 24 22 20 16 14 N.C N.C N.C N.C N.C N.C N.C N.C 12 10 8 Scroll Lock(LED) Caps Lock(LED) Num Lock(LED) P26 P50/INT0 P52/INT1 P54 P56 P00/KI0 P02/KI2 P04/KI4 VCC TP27 GND 1 5V TP26 VCC 1 TP25 5V 1 1 TP24 GND 40 38 36 34 33 32 30 28 VCC 31 29 27 25 23 21 19 17 15 13 11 9 7 6 5 4 3 1 CN9 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 3 4 4 M3A-8K02G01 RENESAS SOLUTIONS Corp. Title M3A-8K02 G01 1 2 3 4 Size A3 Document Number Date: Monday, September 29, 2003 Rev DW30146 (3/3) Sheet 5 3 of 3 C D E 15 13 11 9 7 5 3 1 CNVss2 B Vss VccE CNVss P16/DQ6/AN6 P14/DQ4/AN4 P12/DQ2/AN2 A CN1 4 BC1 BC2 BC3 C1 0.1uF 0.1uF 0.1uF 2.2uF P60(LED0) Vcc PVcc DVcc USB Vref CN2 CN3 P61(LED1) P63(LED3) PVcc USB Vref D0+ P20/D1P22/D2P24 68pF PVss X1 **6MHz CSTCR6M00G15 57 56 55 54 53 52 51 Vss 38K0/38K2 Vref 100P6S-A P00/KI0 P01/KI1 P02/KI2 P03/KI3 P04/KI4 P05/KI5 NC NC Vcc 49 48 P60(LED0) CNVss2 BC4 0.1uF C8 **30pF 47 X2 **12MHz 46 45 44 Vss 2 43 42 41 40 39 38 37 36 35 34 33 32 31 C9 **30pF Vref VccE RESET BC6 0.1uF BC5 0.1uF CNVss NC NC NC NC NC NC NC NC CNVss P17/DQ7/AN7 P16/DQ6/AN6 P15/DQ5/AN5 P14/DQ4/AN4 P13/DQ3/AN3 P12/DQ2/AN2 NC NC CN4 1 50 24 25 26 27 28 29 30 P30 P31 P32 P33/ExINT P34/ExCS P35/ExWR P36/ExRD P37/ExA0 P10/DQ0/AN0 P11/DQ1/AN1 14 15 16 17 18 19 20 21 22 23 P30 P31 P32 P33/ExINT P34/ExCS P35/ExWR P36/ExRD P37/ExA0 P40/ExDreq/RxD P41/ExDack/TxD P42/ExTc/SCLK P43/ExA1/SRDY VccE RESET 10 11 12 13 P10/DQ0/AN0 P36/ExRD P34/ExCS P32 P30 P42/ExTC/SCLK P40/ExDREQ/RxD P06/KI6 15 13 11 9 7 5 3 1 2 NC NC NC NC NC NC NC 60 59 58 61 PVss USBVref DVcc PVcc P63(LED3) P62(LED2) P61(LED1) 64 63 62 71 70 69 68 67 66 65 P23/D2+ P22/D2P21/D1+ P20/D1D0D0+ TrON 73 72 P53 P54 P55 P56 P57 1 2 3 4 5 6 7 1 Xout Xin IC1 P40/ExDREQ/RxD P41/ExDACK/TxD P42/ExTC/SCLK P43/ExA1/SRDY 93 94 95 96 97 98 99 100 Vcc NC NC NC NC NC NC NC P00/KI0 P01/KI1 P02/KI2 P03/KI3 P04/KI4 P05/KI5 P50/INT0 P51/CNTR0 P52/INT1 P06/KI6 P07/KI7 2 88 89 90 91 92 NC P60(LED0) CNVss2 8 9 P53 P54 P55 P56 P57 85 86 87 NC NC P26 P27 P06/KI6 P07/KI7 P26 P27 P50/INT0 P51/CNTR0 P52/INT1 P25 P24 NC NC NC NC NC NC NC 80 79 78 77 76 75 74 3 81 82 83 84 16 14 12 10 8 6 4 2 3 2 4 6 8 10 12 14 16 C7 68pF P11/DQ1/AN1 P37/ExA0 P35/ExWR P33/ExINT P31 P43/ExA1/SRDY P41/ExDACK/TxD P07/KI7 1 3 5 7 9 11 13 15 C6 68pF P62(LED2) PVss DVcc TrON D0P21/D1+ P23/D2+ P25 P26 P50/INT0 P52/INT1 P54 P56 P00/KI0 P02/KI2 P04/KI4 C5 68pF 2 4 6 8 10 12 14 16 P63(LED3) P62(LED2) P61(LED1) C4 68pF TrON C3 68pF P25 P24 C2 1 3 5 7 9 11 13 15 P27 P51/CNTR0 P53 P55 P57 P01/KI1 P03/KI3 P05/KI5 D0+ D0P20/D1P21/D1+ P22/D2P23/D2+ 3 Vref RESET P17/DQ7/AN7 P15/DQ5/AN5 P13/DQ3/AN3 16 14 12 10 8 6 4 2 4 P17/DQ7/AN7 P16/DQ6/AN6 P15/DQ5/AN5 P14/DQ4/AN4 P13/DQ3/AN3 P12/DQ2/AN2 P11/DQ1/AN1 P10/DQ0/AN0 1 BC7 BC8 BC9 BC10 BC11 BC12 BC13 M3A-8K02G02 BC14 RENESAS SOLUTIONS Corp. **0.1uF **0.1uF **0.1uF **0.1uF **0.1uF **0.1uF **0.1uF **0.1uF Title M3A-8K02 G02 **= Pattern only A B C D Size A3 Document Number Date: Monday, September 29, 2003 Rev DW30147 Sheet E 1 of 1 C D E CNVss2 B BC3 **0.1uF **0.1uF BC4 BC5 BC6 BC7 BC8 **0.1uF **0.1uF **0.1uF **0.1uF **0.1uF P60(LED0) Vcc **0.1uF BC2 X1 **6MHz CSTCR6M00G15 3 CN2 1 1 3 5 7 9 11 13 15 P62(LED2) PVss DVcc TrON D0P21/D1+ P23/D2+ P25 2 4 6 8 10 12 14 16 P11/DQ1/AN1 P37/ExA0 P35/ExWR P33/ExINT P31 P43/ExA1/SRDY P41/ExDACK/TxD P07/KI7 16 14 12 10 8 6 4 2 P10/DQ0/AN0 P36/ExRD P34/ExCS P32 P30 P42/ExTC/SCLK P40/ExDREQ/RxD P06/KI6 15 13 11 9 7 5 3 1 P27 P51/CNTR0 P53 P55 P57 P01/KI1 P03/KI3 P05/KI5 C1 **30pF X2 **12MHz 4 CN3 P61(LED1) P63(LED3) PVcc USB Vref D0+ P20/D1P22/D2P24 2 3 CN1 Vref RESET P17/DQ7/AN7 P15/DQ5/AN5 P13/DQ3/AN3 BC1 16 14 12 10 8 6 4 2 15 13 11 9 7 5 3 1 P17/DQ7/AN7 P16/DQ6/AN6 P15/DQ5/AN5 P14/DQ4/AN4 P13/DQ3/AN3 P12/DQ2/AN2 P11/DQ1/AN1 P10/DQ0/AN0 4 Vss VccE CNVss P16/DQ6/AN6 P14/DQ4/AN4 P12/DQ2/AN2 A C2 **30pF 3 Vcc 2 4 6 8 10 12 14 16 BC9 0.1uF CN4 1 3 5 7 9 11 13 15 Vss P07/KI7 P06/KI6 23 24 25 26 27 28 29 30 P24 P25 31 32 USBVref TrON D0+ D0P20/D1P21/D1+ P22/D2P23/D2+ P24 P25 P26 P50/INT0 P52/INT1 P54 P56 P00/KI0 P02/KI2 P04/KI4 P17/DQ7/AN7 P16/DQ6/AN6 P15/DQ5/AN5 P14/DQ4/AN4 P13/DQ3/AN3 P12/DQ2/AN2 VccE RESET CNVss 9 8 7 6 5 4 3 2 1 Vref 10 P17/DQ7/AN7 P16/DQ6/AN6 P15/DQ5/AN5 P14/DQ4/AN4 P13/DQ3/AN3 P12/DQ2/AN2 Vref VccE RESET CNVss Vss 11 Vss Vcc 13 12 14 Vcc Xout Xin IC2 64P6U-A USB Vref TrON D0+ D0P20/D1P21/D1+ P22/D2P23/D2+ P00/KI0 P01/KI1 P02/KI2 P03/KI3 P04/KI4 P05/KI5 50 49 P43/ExA1/SRDY P42/ExTC/SCLK P41/ExDACK/TxD P40/ExDREQ/RxD PVcc DVcc P11/DQ1/AN1 P10/DQ0/AN0 P37/ExA0 P36/ExRD P35/ExWR P34/ExCS P33/ExINT P32 P31 P30 P43/ExA1/SRDY P42/ExTc/SCLK P41/ExDACK/TxD P40/ExDREQ/RxD P07/KI7 P06/KI6 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 P11/DQ1/AN1 P10/DQ0/AN0 P37/ExA0 P36/ExRD P35/ExWR P34/ExCS P33/ExINT P32 P31 P30 P43/ExA1/SRDY P42/ExTC/SCLK P41/ExDACK/TxD P40/ExDREQ/RxD P07/KI7 P06/KI6 P00/KI0 P01/KI1 P02/KI2 P03/KI3 P04/KI4 P05/KI5 54 53 52 51 21 22 P61(LED1) P62(LED2) P63(LED3) PVss 38K0/38K2 43 44 45 46 47 48 D0+ D0P20/D1P21/D1+ P22/D2P23/D2+ P53 P54 P55 P56 P57 P24 P25 M3A-8K02G03 1 68pF 68pF 68pF C7 68pF C8 68pF C9 P53 P54 P55 P56 P57 P26 P27 P53 P54 P55 P56 P57 P00/KI0 P01/KI1 P02/KI2 P03/KI3 P04/KI4 P05/KI5 C6 P50/INT0 P51/CNTR0 P52/INT1 C5 P00/KI0 P01/KI1 P02/KI2 P03/KI3 P04/KI4 P05/KI5 C4 P50/INT0 P51/CNTR0 P52/INT1 RENESAS SOLUTIONS Corp. P26 P27 1 31 32 33 34 P24 P25 P07/KI7 P06/KI6 38 39 40 41 42 2.2uF P43/ExA1/SRDY P42/ExTc/SCLK P41/ExDACK/TxD P40/ExDREQ/RxD P50/INT0 P51/CNTR0 P52/INT1 C3 0.1uF USBVref TrON D0+ D0P20/D1P21/D1+ P22/D2P23/D2+ 35 36 37 BC14 23 24 25 26 27 28 29 30 P26 P27 TrON PVcc DVcc 17 18 19 20 2 43 44 45 46 47 48 64P6Q-A USB Vref P61(LED1) P62(LED2) P63(LED3) PVss P53 P54 P55 P56 P57 38K0/38K2 P60(LED0) CNVss2 P17/DQ7/AN7 P16/DQ6/AN6 P15/DQ5/AN5 P14/DQ4/AN4 P13/DQ3/AN3 P12/DQ2/AN2 6 5 4 3 2 1 IC1 P60(LED0) CNVss2 RESET CNVss 9 8 7 10 Vref VccE RESET CNVss 13 12 11 Vss Vcc Xout Xin PVcc DVcc P11/DQ1/AN1 P10/DQ0/AN0 P37/ExA0 P36/ExRD P35/ExWR P34/ExCS P33/ExINT P32 P31 P30 38 39 40 41 42 21 22 64 63 62 61 60 59 58 57 56 55 P50/INT0 P51/CNTR0 P52/INT1 0.1uF P11/DQ1/AN1 P10/DQ0/AN0 P37/ExA0 P36/ExRD P35/ExWR P34/ExCS P33/ExINT P32 P31 P30 35 36 37 0.1uF P61(LED1) P62(LED2) P63(LED3) PVss P26 P27 BC13 17 18 19 20 BC11 0.1uF 33 34 BC12 P61(LED1) P62(LED2) P63(LED3) PVss P17/DQ7/AN7 P16/DQ6/AN6 P15/DQ5/AN5 P14/DQ4/AN4 P13/DQ3/AN3 P12/DQ2/AN2 PVcc DVcc 14 P60(LED0) 16 15 P60(LED0) CNVss2 2 BC10 0.1uF 16 15 Vref VccE CNVss2 Title M3A-8K02 G03 68pF **= Pattern only A B C D Size A3 Document Number Rev Date: Monday, September 29, 2003 DW30148 Sheet E 1 of 1 1 2 3 TP1 1 P00 P01 P02 P03 P04 P05 P06 P07 1 2 3 4 5 6 7 8 TP2 1 2 3 4 5 6 7 8 P10 P11 P12 P13 P14 P15 P16 P17 P00 P01 P02 P03 P04 P05 P06 P07 P0 4 3 2 1 P4 TP4 1 2 3 4 5 6 7 8 P30 P31 P32 P33 P34 P35 P36 P37 P20 P21 P22 P23 P24 P25 P26 P27 P2 TP6 1 2 3 4 5 6 7 8 P50 P51 P52 P53 P54 P55 P56 P57 RxD TxD SCLK SRDY 5 TP3 1 2 3 4 5 6 7 8 P20 P21 P22 P23 P24 P25 P26 P27 P10 P11 P12 P13 P14 P15 P16 P17 P1 TP5 P40 P41 P42 P43 4 1 P30 P31 P32 P33 P34 P35 P36 P37 P3 TP7 4 3 2 1 P60 P61 P62 P63 INT0 CNTR0 INT1 P53 P54 P55 P56 P57 P60 P61 P62 P63 P6 P5 P54 P55 P56 P57 R1 300 R2 100k TP17 GND 1 TP18 GND 1 1 TP16 GND 1 TP15 GND 3 4 TP14 POWER GND 2 1 P00 P01 P02 P03 P10 P11 P12 P13 P20 P21 P22 P23 P30 P31 P32 P33 P40 P41 P42 P43 P50 P51 P52 P53 P60 P61 P62 P63 TP13 Vcc C1 + **10uF 3 LED1 2 32b 31b 30b 29b 28b 27b 26b 25b 24b 23b 22b 21b 20b 19b 18b 17b 16b 15b 14b 13b 12b 11b 10b 9b 8b 7b 6b 5b 4b 3b 2b 1b TP12 Vcc 5,6 1 32a 31a 30a 29a 28a 27a 26a 25a 24a 23a 22a 21a 20a 19a 18a 17a 16a 15a 14a 13a 12a 11a 10a 9a 8a 7a 6a 5a 4a 3a 2a 1a TP11 Vcc 1 TP10 Vcc 7,8 S1 POWER SW 3 3 IC1 FY4DJ-03A 1 1 P04 P05 P06 P07 P14 P15 P16 P17 P24 P25 P26 P27 P34 P35 P36 P37 32b 31b 30b 29b 28b 27b 26b 25b 24b 23b 22b 21b 20b 19b 18b 17b 16b 15b 14b 13b 12b 11b 10b 9b 8b 7b 6b 5b 4b 3b 2b 1b 1 TP9 5V IN CN1 32a 31a 30a 29a 28a 27a 26a 25a 24a 23a 22a 21a 20a 19a 18a 17a 16a 15a 14a 13a 12a 11a 10a 9a 8a 7a 6a 5a 4a 3a 2a 1a 1 TP8 RESET 2 1 2 HEADER 32X2 4 4 M3A-8K02G04 RENESAS SOLUTIONS Corp. Title M3A-8K02 G04 **= Pattern only 1 2 3 4 Size A3 Document Number Date: Monday, September 29, 2003 Rev DW30149 Sheet 5 1 of 1