Chip tantalum capacitors with (Fail-safe open structure type) TCFG series D Case Dimensions (Unit : mm) Features 1) Safety design by open function built - in. 2) Wide capacitance range 3) Screening by thermal shock. Anode mark L W1 H W2 S + S − Case code L W1 W2 H S D 7343-30(2917) 7.3+ −0.2 4.3 + −0.2 2.4+ −0.1 2.8+ −0.2 1.3+ −0.2 Part No. Explanation T C F G D 0 J 2 2 7 M C R 2 1 1 Series name 4 3 5 6 4 Capacitance TCFG Nominal capacitance in pF 3 digits : 2 significant figure representing the number of 0's. 2 Case code TCFG ······ D 5 Capacitance tolerance 3 Rated Voltage Rated voltage (V) CODE 4 6.3 10 16 20 25 0G 0J 1A 1C 1D 1E M: + − 20% 6 Taping C : Reel width (12mm) R : Positive electrode on the side opposite to sprocket hole www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 1/6 2010.01 - Rev.G TCFG Series D Case Data Sheet Capacitance range TCFG series D Case Rated voltage (V) (μF) 4 0G 6.3 0J 10 1A 16 1C 20 1D 47 (476) D D∗ 68 (686) 100 (107) D 150 (157) D 220 (127) 330 (337) 25 1E D D∗ Remark) Case size codes (D) in the above shown each size products line-up. ∗ : Under development Marking The indication listed below should be given on the surface of a capacitor. Polarity Rated DC voltage Nominal capacitance [D Case] : The polarity should be shown by bar. (on the anode side) note 1) Visual typical example (1) capacitance code (2) voltage code (1) 220μF (2) 6.3V 220 6.3V note 2) voltage code and capacitance code are variable with parts number www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 2/6 2010.01 - Rev.G TCFG Series D Case Data Sheet Characteristics Item Test conditions (based on JIS C5101-1 and JIS C5101-3) Performance Operating Temperature −55 °C to +125 °C Voltage reduction when temperature exceeds +85°C Maximum operating temperature +85 °C with no voltage derating 4 6.3 10 16 20 25 at 85°C Category Voltage (V.DC) 2.5 4 6.3 10 13 16 at 125°C Surge Voltage 5.0 8 Rated Voltage (V.DC) at 85°C 13 20 26 32 DC leakage current 0.5μA or 0.01CV whichever is greater (Shown in "Standard list") As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 1 min Capacitance tolerance Shall be satisfied allowance range. ±20% As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms, +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Tangent of loss angle (Df, tanδ) Shall be satisfied the voltage on "Standard list" As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms, +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Impedance Shall be satisfied the voltage on "Standard list" As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less Measuring circuit : DC Equivalent series circuit Resistance to Appearance There should be no significant abnormality. The indications should be clear. soldering heat L.C ΔC / C tanδ As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 TCFGD1E476 : Less than 150% of initial limit Dip in the solder bath Solder temp : 260±10°C : Less than initial limit Others Duration : 5±0.5s Within ±12% of initial value Repetition :1 After the specimens, leave it at room temperature for Less than 150% of initial limit over 24h and then measure the sample. Dip in the solder bath Solder temp : 330±5°C Fail-Safe open unit actuation Within 330°C − 20s Temperature cycle As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) TCFGD1E476 : Less than 150% of initial limit without discontinuation. : Less than initial limit Others Step Temp. Time Within ±20% of initial value + −55 + 3 1 °C 30 − −3min Less than 150% of initial limit 2 Room temp. 3min. or less + 2°C 3 125 − 30 + −3min Appearance There should be no significant abnormality. L.C ΔC / C tanδ 4 Room temp. 3min. or less After the specimens, leave it at room temperature for over 24h and then measure the sample. Moisture resistance Appearance There should be no significant abnormality. The indications should be clear. L.C ΔC / C tanδ As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 TCFGD1E476 : Less than 150% of initial limit After leaving the sample under such atmospheric condition that the temperature and humidity are : Less than initial limit Others 60±2°C and 90 to 95%RH, respectively, for Within ±20% of initial value 500±12h level it at room temperature for over 24h and then measure the sample. Less than 150% of initial limit www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 3/6 2010.01 - Rev.G TCFG Series D Case Item Temperature Temp. Stability ΔC / C tanδ Data Sheet −55°C As per 4.29 JIS C 5101-1 As per 4.13 JIS C 5101-3 Within 0/−20%of initial value Shall be satisfied the voltage on "Standard list" − L.C Surge Voltage Test conditions (based on JIS C5101-1 and JIS C5101-3) Performance Temp. +85°C ΔC / C Within +12/0%of initial value tanδ Shall be satisfied the voltage on "Standard list" L.C Less than 1000% of initial limit Temp. +125°C ΔC / C Within +20/0%of initial value tanδ Shall be satisfied the voltage on "Standard list" L.C Less than 1250% of initial limit Appearance There should be no significant abnormality. As per 4.26 JIS C 5101-1 As per 4.14 JIS C 5101-3 Apply the specified surge voltage via the serial resistance of 1kΩ every 5±0.5min.for 30±5 s. each time in the atmospheric condition of 85±2°C. Repeat this procedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. : Less than 150% of initial limit : Less than initial limit L.C TCFGD1E476 Others ΔC / C Within ±10%of initial value tanδ Less than 150% of initial limit Loading at Appearance There should be no significant abnormality. High TCFGD1E476 : Less than 150% of initial limit temperature L.C : Less than 125% of initial limit Others Terminal Strength ΔC / C Within ±10%of initial value tanδ Less than 150% of initial limit As per 4.23 JIS C 5101-1 As per 4.15 JIS C 5101-3 After applying the rated voltage for 2000+72/0h without discontinuation via the serial resistance of 3Ω or less at a temperature of 85±2°C, leave the sample at room temperature/humidity for over 24h and measure the value. Capacitance The measured value should be stable. As per 4.35 JIS C 5101-1 As per 4.9 JIS C 5101-3 A force is applied to the terminal until it bends to 1mm and by a prescribed tool maintain the condition for 5s. (See the figure below.) Appearance There should be no significant abnormality. (Unit : mm) 20 50 F (Apply force) R230 1 Thickness 1.6mm 45 Adhesiveness The terminal should not come off. 45 As per 4.34 JIS C 5101-1 As per 4.8 JIS C 5101-3 Apply force of 5N in the two directions shown in the figure below for 10±1s after mounting the terminal on a circuit board. product YAA C105 Apply force a circuit board www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 4/6 2010.01 - Rev.G TCFG Series D Case Data Sheet Item Test conditions (based on JIS C5101-1 and JIS C5101-3) Performance Dimensions Be based on "External dimensions" Measure using a caliper of JIS B 7505 Class 2 or higher grade. Resistance to solvents The indication should be clear. As per 4.32 JIS C 5101-1 As per 4.18 JIS C 5101-3 Dip in the isopropyl alcohol for 30±5s, at room temperature. Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. As per 4.15.2 JIS C 5101-1 As per 4.7 JIS C 5101-3 Dip speed = 25±2.5mm/s Pre-treatment (accelerated aging) : Leave the sample on the boiling distilled water for 1h. Solder temp. : 245±5°C Duration : 3±0.5s Solder : M705 Flux : Rosin 25%, IPA 75% Vibration Capacitance Measure value should not fluctuate during the measurement. Appearance As per 4.17 JIS C 5101-1 Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. There should be no significant abnormality. Table 1 standard list, TCFG series D Case (D : 7343) Part No. Leakage Rated Derated Surge Impedance DF120Hz Capacitance (%) 100kHz Case Tolerance current Voltage Voltage Voltage 120Hz C 25 @85°C @125°C @85°C (%) code 1WV.60s 25 °C 125 °C (F) −55 °C (Ω) (V) (V) (V) (mA) 85˚C ±20 13.8 150 ±20 100 ±20 47 ±20 TCFG D 0J 227 M8R 6.3 4 8 220 TCFG D 1A 157 M8R 10 6.3 13 TCFG D 1C 107 M8R 16 10 20 TCFG D 1E 476 M8R 25 16 32 www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 30 12 16 0.70 D 15.0 14 10 12 0.70 D 16 14 10 12 0.70 D 11.8 14 10 12 0.70 D 5/6 2010.01 - Rev.G TCFG Series D Case Data Sheet Packaging specifications Taping Case code A±0.2 B±0.2 t1±0.1 t2±0.2 D (7343) 4.8 7.7 0.3 3.3 Taping +0.1 0 5.5±0.1 A B t1 12.0±0.3 φ1.5 1.75±0.1 D case Products 8.0±0.1 4.0±0.1 t2 2.0±0.1 Pull out direction Packaging style Packaging Case size D Case Packaging style Taping Plastic taping φ180mm reel Symbol Basic ordering unit R 500 Reel φ60 +10 φ180 −1.50 15.4±1.0 φ13±0.2 13.0 +1.00 Plastic reel Label sticking position EIAJ ET - 7200B compatible www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 6/6 2010.01 - Rev.G Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. R1010A