Chip tantalum capacitors TCO Series B Case zFeatures (B) 1) Conductive polymer used for the cathode material. 2) Ultra-low ESR. (1/10 compared with the conventional type) 3) Screening by thermal shock. zDimensions (Unit : mm) Anode mark (Unit : mm) W1 L Dimensions B case H W2 S S + − L 3.5 + − 0.2 W1 2.8 + − 0.2 W2 1.9 + − 0.2 H 1.9 + − 0.2 S 0.8 + − 0.3 zPart No. Explanation Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. Series name Case style T C O B Nominal capacitance 0 J 4 7 6 M 8 R Capacitance tolerance Rated voltage Code Rated voltage (V) 0E 2.5 0G 4 0J 6.3 1A 10 Code Capacitance tolerance +− 20% M 8 : Tape width R : Positive electrode on the side opposite to sprocket hole zRated Table Rated voltage (V.DC) µF 2.5 0E 4 0G 6.3 0J 10 1A j 22 n 33 B B B ∗B B s 47 w 68 a 100 e 150 j 220 ∗B 330 ∗B n B B ∗B ∗B ∗ Under development indicates new product www.rohm.com c 2009 ROHM Co., Ltd. All rights reserved. ○ 1/5 2009.01 - Rev.E Data Sheet TCO Series B Case zMarking The indications listed below should be given on the surface of a capacitor. (1) Polarity : The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage : Due to the small size of B case, a voltage code is used as shown below. (3) Visual typical example (1) voltage code (2) capacitance code Rated DC Voltage (V) 2.5 Capacitance Code a Nominal Capacitance (µF) 10 g 4 e 15 j 6.3 j 22 A 10 n 33 s 47 Voltage Code e [B case] note 1) w 68 a 100 e 150 j 220 n 330 j s − − (1) (2) js manufacture code note 2) voltage code and capacitance code are variable with parts number zCharacteristics Item Operating Temperature Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Performance −55 C to +105 C Voltage reduction when temperature exceeds+85 C Maximum operating +85 C temperature with no voltage derating Rated voltage (VDC) 2.5 4 6.3 10 Category voltage (VDC) Surge voltage (VDC) 2 3.2 5 at 85 C 8 at 105 C 3.2 5.2 8 13 at 85 C DC Leakage current 3µA or 0.1CV whichever is greater Shown in " Standard list " Rated voltage for 5min Capacitance tolerance + −20% Shall be satisfied allowance range. Tangent of loss angle (Df, tan δ) Measuring frequency : 120+ −12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Shall be satisfied the voltage on " Standard list " Measuring frequency : 120 + −12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC Measuring circuit : DC Equivalent series circuit Shall be satisfied the voltage on " Standard list " Measuring frequency : 100 + −10kHz Measuring voltage : 0.5Vrms or less ESR Resistance to Appearance There should be no significant abnormality. The indications should be clear. Soldering heat ∆C / C Less than 150% of initial limit Within + − 20% of initial value tan δ Less than 150% of initial limit L.C. www.rohm.com c 2009 ROHM Co., Ltd. All rights reserved. ○ Dip in the solder bath +5 C Solder temp : 240− Duration : 10+ −0.5s :1 Repetition After the specimens, leave it at room temperature for over 24h and then measure the sample. 2/5 2009.01 - Rev.E Data Sheet TCO Series B Case Item Temperature cycle Moisture resistance Temperature Stebility Appearance There should be no significant abnormality. L.C Less than 500% of initial limit ∆C / C Within+ −20% of intial value Df (tan δ) Less than 150% of initial limit Temp. −55+ 1 −3 C 2 Room temp. +2 C 105− 3 4 Room temp. Appearance There should be no significant abnormality. The indications should be L.C Less than 150% of initial limit ∆C / C +30% / −20% Df (tan δ) Less than 150% of initial limit Temp. −55 C ∆C / C Within 0/−20% of initial value Df (tan δ) Shall be satisfied the voltage on " Standard list " Temp. +105 C Within +50/0% of initial value Df (tan δ) Shall be satisfied the voltage on " Standard list " L.C Less than 1CV Appearance There should be no significant abnormality. ∆C / C Df (tan δ) Time +3min 30− 3min.or less 30+ −3min 3min.or less After leaving the sample under such atmospheric condition that the temperature and humidity are + 2 C and 90 to 95% RH,respectiveiy,for 500 − +24h 40 − leave it at room temperature for over 24h and then measure the sample. − ∆C / C L.C Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation. After the specimens, leave it at room temperature for over 24h and then measure the sample. L.C Surge voltage Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Performance Less than initial limit Within + − 20% of initial value Less than initial limit www.rohm.com c 2009 ROHM Co., Ltd. All rights reserved. ○ 3/5 Apply the specified serge voltage every 5+ − 0.5 min. for 30+ −5 s. each time in the atmospheric condition of 85+ −2 C. Repeat this rocedure 1,000 times. After the specimens, leave it at room temperature for over 24h and then measure the sample. 2009.01 - Rev.E Data Sheet TCO Series B Case Item Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Performance After applying the rated voltage for 1000+72 h without discontinuation via the serial resistance of 3Ω or less at a temperature of 85+ − 2 C, leave the sample at room temperature / humidity for over 24h and measure the value. Loading at Appearance There should be nonsignificant High temperature abnormality. L.C Less than 200% of initial limit ∆C / C Within + − 20% of initial value Df (tan δ) 150% of initial limit less than Terminal strength Capacitance The measured value should be stable. Appearance There should nonsignificant abnormality. A force is applied to the terminal until it bends to 1mm and by a perscribed tool maintain the condition for5s.(See the figure below) 20 50 (Unit : mm) F (Apply force) R230 1mm thickness=1.6mm 45 Adhesiveness The terminal should not come off. 45 Apply force of 5N in the two directions shown + 1s after mounting the in the figure below for 10 − terminal on a circuit board. product YAA C105 Apply force a circuit board Dimensions Refer to "External dimensions" Measure using a caliper of JISB 7507 Class 2 or higher grade. Resistance to solvents The indication should be clear Solderability 3/4 or more surface area of the solder coated terminal dipped in the soldering bath should be covered with the new solder. +5s, at room Dip in the isopropyl alcohol for 30− temperature. Dip speed=25 + − 2.5mm / s Pre−treatment(accelerated aging): Leave the sample on the boiling distilled water for 1 h. Solder temp. . : 245 + −5 C : 3+ Duration − 0.5s : M705 Solder : Rosin25% Flux IPA75% Frequency : 10 to 55 to 10Hz/min. Amplitude : 1.5mm Time : 2h each in X and Y directions Mounting : The terminal is soldered on a print circuit board. Vibration Capacitance Measure value should not fluctuate during the measurement. Appearance There should no significant abnormality. www.rohm.com c 2009 ROHM Co., Ltd. All rights reserved. ○ 4/5 2009.01 - Rev.E Data Sheet TCO Series B Case zStandard list, TCO series < B case : 3528 size > Part No. TCO TCO TCO TCO TCO TCO Rated Voltage 85°C Category Voltage 105°C Surge Voltage 85°C Cap. 120Hz (V) (V) (V) (µF) 4 6.3 6.3 6.3 10 10 3.2 5 5 5 8 8 5 8 8 8 13 13 150 33 47 100 33 47 B 0G 157 M B 0J 336 M B 0J 476 M B 0J 107 M B 1A 336 M B 1A 476 M Df ESR Tolerance Leakage 120Hz 100kHz Current (%) 25°C 1WV 5min 25°C 105°C (mΩ) −55°C (µA) (%) 85°C + − 20 + − 20 + − 20 + − 20 + 20 − + − 20 60 21 30 63 33 47 8 8 8 8 8 8 8 8 8 8 8 8 12 12 12 12 12 12 150 150 150 150 150 150 zPackaging specifications Reek [ B case ] Chip 4.0±0.1 t2 2.0±0.05 Pull-out direction 0 φ180 −1.5 4.0±0.1 11.4+ −1.0 φ60 +1 0 B +1.0 9.0 0 3.5±0.05 A t1 φ13+ −0.2 +0.1 −0 8.0±0.2 φ1.5 1.75±0.1 Tape [ B case ] Unit : [mm] Case A+ −0.1 B+ −0.1 B 3.3 3.8 t1 + − 0.05 0.25 Pull direction Labelsticling position t2 + −0.1 2.2 EIAJ ET−7200B compatible zPackaging style Case code package B Taping Packaging style plastic taping Symbol Basic ordering units φ180mmReel R 2,000pcs zDamp proof package One reel is packed in aluminum bag. The size of aluminum bag is 240(a) x 250(b)mm. The size up to 230(c)mm is to zipper. A desiccant is packed with a reel. The aluminum bag is heat-sealed. The label of the same as the label on the reel is placed on the aluminum bag. b C a www.rohm.com c 2009 ROHM Co., Ltd. All rights reserved. ○ 5/5 2009.01 - Rev.E Appendix Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM CO.,LTD. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2009 ROHM Co.,Ltd. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster @ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix-Rev4.0