VT-490 Temperature Compensated Crystal Oscillator Previous Vectron Model OSC VT-490 Description Vectron’s VT-490 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, clipped sine wave output, analog temperature compensated oscillator, operating off either 3.0 or 5.0 volt supply built on a 9.9x11.8 FR4 board with a cover. Features • • • • • • Applications Clipped Sine Wave Output Output Frequencies to 40 MHz Fundamental Crystal Design Optional VCXO Function available Gold over nickel contact pads SMD package • • • • • Wireless Communications Base Stations Point to point radios Broadband Access Test Equipment • Product is compliant to RoHS directive and fully compatible with lead free assembly Block Diagram Output VDD Crystal Analog Temperature Comp. Vcontrol or NC Gnd Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page1 Performance Specifications Table 1. Electrical Performance Parameter Output Frequency Symbol Min. fO 10 Supply Voltage1 VDD Supply Current, 8-16.800MHz 16.801-25.9999MHz 26.000-40.000MHz IDD Operating Temperature, (Ordering Option) TOP Typ Max Units 40 MHz +3.0 or +5.0 V 2.0 3.0 4.0 mA -20/70, -30/80, -40/85 °C ±1.5, ±2.0, ±2.5, ±5.0 ppm Stability Over TOP, (Ordering Option) Initial Accuracy, “No Adjust” Option ±1.0 ppm Power Supply Stability, 10-16.800MHz 16.801-25.9999MHz 26.000-40.000MHz ±0.3 ±0.5 ±1.0 ppm Load Stability ±0.5 ppm ±1 ppm/yr Aging 3 Pull Range, Mechanical Trim Only Electrical and Mechanical Trim Electrical Trim only TPR ppm ±8 ±5 ±8 Control Voltage to reach Pull Range, 5V 3.0V option 0.5 0.5 Control Voltage Impedance 100 Kohm 1.0 0.7 V 2, Output Level , 5V option 3.0V option VO p/p 4.5 2.5 Output Load V 10K II 10pF dBc/Hz Phase Noise, 10.000MHz 10Hz 100Hz 1kHz 10kHz 100kHz -100 -123 -133 -143 -151 Start Up Time 10 ms 1. The OSC power supply pin should be filtered, eg, a 0.1 and 0.01uf capacitor 2. The Output is AC coupled 3. A special trim tool, KMTZ04, should be used to adjust the frequency Outline Drawing Recommended Pad Layout 1.9 9.9 max 1.3±0.1 0.7 7.62 1.4 7.62 11.8 max 1.0±0.1 8.4 2.2 max Table 2. Pinout Dimensions in mm 0.55 Pin # Symbol Function 1 VC TCXO Control Voltage or Ground 2 GND Electrical and Lid Ground 3 fo Output Frequency 4 VDD Supply Voltage Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page2 S VCXO Function VCXO Feature: The VT-490 can be ordered with a VCXO function for applications were it will be used in a PLL, or the output frequency needs fine tune or calibration adjustments. This is a high impedance input , 1Mohm, and can be driven with an op-amp or terminated with adjustable resistors etc. Pin 1 should not be left floating on the VCXO optional device. “No Adjust” Option: In applications were the VT-490 will not be used in a PLL , or the output frequency does not need fine tune adjustments, the best device to use would be a VT-490-xxx-xxx0. By using the “no adjust” option, the circuit is simplified as Vc does not need to be adjusted or set to a predetermined voltage and pin 1 should be grounded (pin 1 can be left open but should not be set to a voltage such as an RF signal or power supply voltage. Output Waveform Phase Noise S Maximum Ratings Absolute Maximum Ratings and Handling Precautions Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied or any other excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Although ESD protection circuitry has been designed into the VT-490, proper precautions should be taken when handling and mounting, VI employs a Human Body Model and Charged Device Model for ESD susceptibility testing and design evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry standard has been adopted for the CDM a standard resistance of 1.5kOhms and capacitance of 100pF is widely used and therefor can be used for comparison purposes. Table 3. Maximum Ratings Parameter Symbol Rating Unit Storage Temperature TSTORE -55/125 ºC Supply Voltage VDD 6 V Control Voltage VC 0/VDD V ESD, Human Body Model 1500 V ESD, Charged Device Model 1000 V Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page3 Table 4. Environmental Compliance Parameter Condition Mechanical Shock MIL-STD-883 Method 2002 Mechanical Vibration MIL-STD-883 Method 2007 Temperature Cycle MIL-STD-883 Method 1010 Solderability MIL-STD-883 Method 2003 Fine and Gross Leak MIL-STD-883 Method 1014 Resistance to Solvents MIL-STD-883 Method 2015 Moisture Sensitivity Level MSL1 Contact Pads Gold over Nickel S IR Reflow Suggested IR Profile Devices are built using lead free epoxy and can be subjected to standard lead free IR reflow conditions shown in Table 5. Contact pads are gold over nickel and lower maximum temperatures can also be used, such as 220C. Table 5. Reflow Profile Parameter Symbol Value PreHeat Time Ts-min Ts-max ts 200 sec Max 150°C 200°C Ramp Up RUP 3ºC/sec Max Time above 217C tL 150 sec Max Time to Peak Temperature t25C to peak 480 sec Max Time at 260C tP 10 sec Max Time at 240C tP2 60 sec Max Ramp down RDN 6ºC/sec Max Tape and Reel Information Table 6. Tape and Reel Information Tape Dimensions (mm) Reel Dimensions (mm) W F Do Po P1 A B C D N W1 W2 #/Reel 16 7.5 1.5 4 8 180 1.5 13 20.2 60 16.4 20.4 1000 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page4 Table 7. Standard Frequencies (MHz) 10.000 10.245 12.504 12.800 13.000 13.568 14.000 14.31818 14.4844 14.7456 15.000 16.000 16.325291 16.36625 16.367667 16.3683 16.396 16.800 17.500 18.414 19.200 19.440 19.6608 19.680 19.800 20.000 20.910 21.250 23.104 24.000 24.5454 24.5535 24.576 25.000 25.600 26.000 27.000 27.456 28.800 32.768 40.000 Ordering Information VT- 490- F F J - 206 A- xxMxxxxxxx Frequency in MHz Product TCXO Tuning 0: Fixed, Mechanical tuning only A: ±5ppm Mechanical and Electrical B: ±8ppm Electrical tuning only Package 9.9x11.8, FR4, trim Voltage Options D: +5.0 Vdc ±5%, F: +3.0 Vdc ±5% Stability 156: ±1.5ppm 206: ±2.0ppm 256: ±2.5ppm 506: ±5.0ppm Output F: Clipped Sine Wave Temp Range J: -20/70°C G: -30/80°C E: -40/85°C *Note: not all combination of options are available. Other specifications may be available upon request. Example: VT-490-FFJ-206A-19M2000000 For Additional Information, Please Contact USA: Europe: Asia: Vectron International 267 Lowell Road Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 3328.4784.17 Fax: +49 (0) 3328.4784.30 Vectron International 1F-2F, No 8 Workshop, No 308 Fenju Road WaiGaoQiao Free Trade Zone Pudong, Shanghai, China 200131 Tel: 86.21.5048.0777 Fax: 86.21.5048.1881 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 04/17/2009 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Page5