INTEL TE28F016B3T120

E
PRELIMINARY
SMART 3 ADVANCED BOOT BLOCK
BYTE-WIDE
8-MBIT (1024K x 8), 16-MBIT (2056K x 8)
FLASH MEMORY FAMILY
28F008B3, 28F016B3
n
n
n
n
n
n
n
n
n
Flexible SmartVoltage Technology
 2.7V–3.6V Program/Erase
 2.7V–3.6V Read Operation
 12V VPP Fast Production
Programming
2.7V or 1.8V I/O Option
 Reduces Overall System Power
Optimized Block Sizes
 Eight 8-Kbyte Blocks for Data,
Top or Bottom Locations
 Up to Thirty-One 64-Kbyte Blocks
for Code
High Performance
 2.7V–3.6V: 120 ns Max Access Time
Block Locking
 VCC-Level Control through WP#
Low Power Consumption
 20 mA Maximum Read Current
Absolute Hardware-Protection
 VPP = GND Option
 VCC Lockout Voltage
Extended Temperature Operation
 –40°C to +85°C
n
n
n
n
n
n
n
n
n
Extended Cycling Capability
 10,000 Block Erase Cycles
Automated Byte Program and Block
Erase
 Command User Interface
 Status Registers
SRAM-Compatible Write Interface
Automatic Power Savings Feature
Reset/Deep Power-Down
 1 µA ICCTypical
 Spurious Write Lockout
Standard Surface Mount Packaging
 48-Ball µBGA* Package
 40-Lead TSOP Package
Footprint Upgradeable
 Upgradeable from 2-, 4- and 8-Mbit
Boot Block
ETOX™ V (0.4 µ) Flash Technology
x8-Only Input/Output Architecture
 For Space-Constrained 8-bit
Applications
Supports Code plus Data Storage
 Optimized for FDI, Flash Data
Integrator Software
 Fast Program Suspend Capability
 Fast Erase Suspend Capability
The new Smart 3 Advanced Boot Block, manufactured on Intel’s latest 0.4µ technology, represents a featurerich solution at overall lower system cost. Smart 3 flash memory devices incorporate low voltage capability
(2.7V read, program and erase) with high-speed, low-power operation. Several new features have been
added, including the ability to drive the I/O at 1.8V, which significantly reduces system active power and
interfaces to 1.8V controllers. A new blocking scheme enables code and data storage within a single device.
Add to this the Intel-developed Flash Data Integrator (FDI) software and you have the most cost-effective,
monolithic code plus data storage solution on the market today. Smart 3 Advanced Boot Block Byte-Wide
products will be available in 40-lead TSOP and 48-ball µBGA* packages. Additional information on this
product family can be obtained by accessing Intel’s WWW page: http://www.intel.com/design/flcomp
May 1997
Order Number: 290605-001
Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or
otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions of
Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to
sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or
infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life
saving, or life sustaining applications.
Intel may make changes to specifications and product descriptions at any time, without notice.
The 28F008B3 and 28F016B3 may contain design defects or errors known as errata which may cause the product to deviate
from published specifications. Current characterized errata are available on request.
*Third-party brands and names are the property of their respective owners.
Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order.
Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be
obtained from:
Intel Corporation
P.O. Box 7641
Mt. Prospect, IL 60056-7641
or call 1-800-879-4683
or visit Intel’s website at http:\\www.intel.com
COPYRIGHT © INTEL CORPORATION 1996, 1997
*Third-party brands and names are the property of their respective owners.
CG-041493
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
CONTENTS
PAGE
1.0 INTRODUCTION .............................................5
1.1 Smart 3 Advanced Boot Block Flash
Memory Enhancements ..............................5
1.2 Product Overview.........................................6
2.0 PRODUCT DESCRIPTION..............................6
2.1 Package Pinouts ..........................................7
2.2 Block Organization .....................................11
2.2.1 Parameter Blocks ................................11
2.2.2 Main Blocks .........................................11
3.0 PRINCIPLES OF OPERATION .....................14
3.1 Bus Operation ............................................14
3.1.1 Read....................................................15
3.1.2 Output Disable.....................................15
3.1.3 Standby ...............................................15
3.1.4 Deep Power-Down/Reset ....................15
3.1.5 Write....................................................15
3.2 Modes of Operation....................................15
3.2.1 Read Array ..........................................16
3.2.2 Read Intelligent Identifier .....................17
3.2.3 Read Status Register ..........................17
3.2.4 Program Mode.....................................18
3.2.5 Erase Mode .........................................19
3.3 Block Locking.............................................26
3.3.1 VPP = VIL for Complete Protection .......26
3.3.2 WP# = VIL for Block Locking................26
3.3.3 WP# = VIH for Block Unlocking ............26
3.4 VPP Program and Erase Voltages ..............26
PAGE
3.5 Power Consumption ...................................26
3.5.1 Active Power .......................................26
3.5.2 Automatic Power Savings (APS) .........27
3.5.3 Standby Power ....................................27
3.5.4 Deep Power-Down Mode.....................27
3.6 Power-Up/Down Operation.........................27
3.6.1 RP# Connected to System Reset ........27
3.6.2 VCC, VPP and RP# Transitions .............27
3.7 Power Supply Decoupling ..........................28
3.7.1 VPP Trace on Printed Circuit Boards ....28
4.0 ABSOLUTE MAXIMUM RATINGS ................29
5.0 OPERATING CONDITIONS
(VCCQ = 2.7V–3.6V).......................................29
5.1 DC Characteristics: VCCQ = 2.7V–3.6V.......30
6.0 OPERATING CONDITIONS
(VCCQ = 1.8V–2.2V).......................................34
6.1 DC Characteristics: VCCQ = 1.8V–2.2V.......34
7.0 AC CHARACTERISTICS...............................39
7.1 Reset Operations .......................................43
APPENDIX A: Ordering Information .................45
APPENDIX B: Write State Machine Current/
Next States ..................................................46
APPENDIX C: Access Time vs.
Capacitive Load...........................................47
APPENDIX D: Architecture Block Diagram ......48
APPENDIX E: Additional Information ...............49
PRELIMINARY
3
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
E
REVISION HISTORY
Number
-001
4
Description
Original version
PRELIMINARY
E
1.0
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
INTRODUCTION
1.1
This
preliminary
datasheet
contains
the
specifications for the Advanced Boot Block flash
memory family, which is optimized for low power,
portable systems. This family of products features
1.8V–2.2V or 2.V–3.6V I/Os and a low VCC/VPP
operating range of 2.7V–3.6V for read and
program/erase operations. In addition this family is
capable of fast programming at 12V. Throughout
this document, the term “2.7V” refers to the full
voltage range 2.7V–3.6V (except where noted
otherwise) and “VPP = 12V” refers to 12V ±5%.
Section 1 and 2 provides an overview of the flash
memory family including applications, pinouts and
pin descriptions. Section 3 describes the memory
organization and operation for these products.
Finally, Sections 4, 5, 6 and 7 contain the
operating specifications.
Smart 3 Advanced Boot Block
Flash Memory Enhancements
The new 8-Mbit and 16-Mbit Smart 3 Advanced
Boot Block flash memory provides a convenient
upgrade from and/or compatibility to previous 4Mbit and 8-Mbit Boot Block products. The Smart 3
product functions are similar to lower density
products in both command sets and operation,
providing similar pinouts to ease density upgrades.
The Smart 3 Advanced Boot Block flash memory
features
•
Enhanced blocking for easy segmentation of
code and data or additional design flexibility
•
Program Suspend command which permits
program suspend to read
•
WP# pin to lock and unlock the upper two (or
lower two, depending on location) 8-Kbyte
blocks
•
VCCQ input for 1.8V–2.2V on all I/Os. See
Figures 1–3 for pinout diagrams and VCCQ
location
•
Maximum program time
improved data storage.
specification
for
Table 1. Smart 3 Advanced Boot Block Feature Summary
Feature
28F016B3/28F008B3/28F004B3
Reference
VCC Read Voltage
2.7V– 3.6V
Table 9, Table 12
VCCQ I/O Voltage
1.8V–2.2V or 2.7V– 3.6V
Table 9, Table 12
VPP Program/Erase Voltage
2.7V– 3.6V or 11.4V– 12.6V
Table 9, Table 12
Bus Width
8 bits
Table 2
Speed
120 ns
Table 15
Memory Arrangement
1 Mbit x 8 (8 Mbit), 2 Mbit x 8 (16 Mbit)
Blocking (top or bottom)
Eight 8-Kbyte parameter blocks (8/16 Mbit) &
Fifteen 64-Kbyte blocks (8 Mbit)
Thirty-one 64-Kbyte main blocks (16 Mbit)
Section 2.2
Figures 4 and 5
Locking
WP# locks/unlocks parameter blocks
All other blocks protected using V PP switch
Section 3.3
Table 8
Operating Temperature
Extended: –40°C to +85°C
Table 9, Table 12
Program/Erase Cycling
10,000 cycles
Table 9, Table 12
Packages
40-Lead TSOP, 48-Ball µBGA* CSP
Figures 1, 2, and 3
PRELIMINARY
5
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
1.2
Product Overview
Intel provides the most flexible voltage solution in
the flash industry, providing three discrete voltage
supply pins: VCC for read operation, VCCQ for output
swing, and VPP for program and erase operation.
Discrete supply pins allow system designers to use
the optimal voltage levels for their design. All Smart
3 Advanced Boot Block flash memory products
provide program/erase capability at 2.7V or 12V
and read with VCC at 2.7V. Since many designs
read from the flash memory a large percentage of
the time, 2.7V VCC operation can provide
substantial power savings. The 12V VPP option
maximizes program and erase performance during
production programming.
The Smart 3 Advanced Boot Block flash memory
products are high-performance devices with low
power operation. The available densities for the
byte-wide devices (x8) are
a. 8-Mbit (8,388,608-bit)
flash
memory
organized as 1 Mbyte of 8 bits each
b. 16-Mbit (16,777,216-bit) flash memory
organized as 2 Mbytes of 8 bits each.
For word-wide devices (x16) see the Smart 3
Advanced Boot Block Word-Wide Flash Memory
Family datasheet.
The parameter blocks are located at either the top
(denoted by -T suffix) or the bottom (-B suffix) of the
address map in order to accommodate different
microprocessor protocols for kernel code location.
The upper two (or lower two) parameter blocks can
be locked to provide complete code security for
system initialization code. Locking and unlocking is
controlled by WP# (see Section 3.3 for details).
The Command User Interface (CUI) serves as the
interface
between
the
microprocessor
or
microcontroller and the internal operation of the
flash memory. The internal Write State Machine
(WSM) automatically executes the algorithms and
timings necessary for program and erase
operations, including verification, thereby unburdening the microprocessor or microcontroller.
The status register indicates the status of the WSM
by signifying block erase or byte program
completion and status.
6
E
Program and erase automation allows program and
erase operations to be executed using an industrystandard two-write command sequence to the CUI.
Data writes are performed in byte increments. Each
byte in the flash memory can be programmed
independently of other memory locations; every
erase operation erases all locations within a block
simultaneously. Program suspend allows system
software to suspend the program command in order
to read from any other block. Erase suspend allows
system software to suspend the block erase
command in order to read from or program data to
any other block.
The Smart 3 Advanced Boot Block flash memory is
also designed with an Automatic Power Savings
(APS) feature which minimizes system current
drain, allowing for very low power designs. This
mode is entered immediately following the
completion of a read cycle.
When the CE# and RP# pins are at VCC, the ICC
CMOS standby mode is enabled. A deep powerdown mode is enabled when the RP# pin is at
GND, minimizing power consumption and providing
write protection. ICC current in deep power-down is
1 µA typical (2.7V VCC). A minimum reset time of
tPHQV is required from RP# switching high until
outputs are valid to read attempts. With RP# at
GND, the WSM is reset and Status Register is
cleared. Section 3.5 contains additional information
on using the deep power-down feature, along with
other power consumption issues.
The RP# pin provides additional protection against
unwanted command writes that may occur during
system reset and power-up/down sequences due to
invalid system bus conditions (see Section 3.6).
Refer to the DC Characteristics Table, Sections 5.1
and 6.1, for complete current and voltage
specifications. Refer to the AC Characteristics
Table, Section 7.0, for read, program and erase
performance specifications.
2.0
PRODUCT DESCRIPTION
This section explains device pin description and
package pinouts.
PRELIMINARY
E
2.1
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Package Pinouts
The Smart 3 Advanced Boot Block flash memory is
available in 40-lead TSOP (see Figure 1) and 48ball µBGA packages (see Figures 2 and 3). In
Figure 1, pin changes from one density to the next
are circled. Both packages, 40-lead TSOP and 48ball µBGA package, are 8-bits wide and fully
upgradeable across product densities (from 8 Mb to
16 Mb).
28F016
28F008
28F008
28F016
A16
A15
A14
A13
A12
A11
A9
A8
WE#
RP#
VPP
WP#
A18
A7
A6
A5
A4
A3
A2
A1
A16
A15
A14
A13
A12
A11
A9
A8
WE#
RP#
VPP
WP#
A18
A7
A6
A5
A4
A3
A2
A1
A17
GND
NC
A19
A10
DQ7
DQ6
DQ5
DQ4
VCCQ
VCC
NC
DQ3
DQ2
DQ1
DQ0
OE#
GND
CE#
A0
A17
GND
A20
A19
A10
DQ7
DQ6
DQ5
DQ4
VCCQ
VCC
NC
DQ3
DQ2
DQ1
DQ0
OE#
GND
CE#
A0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Advanced Boot Block
40-Lead TSOP
10 mm x 20 mm
TOP VIEW
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
0605-01
Figure 1. 40-Lead TSOP Package
PRELIMINARY
7
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
1
2
A14
A12
A15
C
D
A
B
E
F
3
4
5
6
7
8
A8
VPP
WP#
NC
A7
A4
A10
WE#
RP#
A19
A18
A5
A2
A16
A13
A9
A6
A3
A1
A17
NC
D5
NC
D2
NC
CE#
A0
VCCQ
A11
D6
NC
D3
NC
D0
GND
GND
D7
NC
D4
VCC
NC
D1
OE#
0605-03
NOTE:
Dotted connections indicate placeholders where there is no solder ball. These connections are reserved for future upgrades.
Routing is not recommended in this area.
Figure 2. 8-Mbit 48-Ball µBGA* Chip Size Package
8
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
1
2
A14
A12
A15
C
D
A
B
E
F
3
4
5
6
7
8
A8
VPP
WP#
A20
A7
A4
A10
WE#
RP#
A19
A18
A5
A2
A16
A13
A9
A6
A3
A1
A17
NC
D5
NC
D2
NC
CE#
A0
VCCQ
A11
D6
NC
D3
NC
D0
GND
GND
D7
NC
D4
VCC
NC
D1
OE#
0605-02
NOTE:
Dotted connections indicate placeholders where there is no solder ball. These connections are reserved for future upgrades.
Routing is not recommended in this area.
Figure 3. 16-Mbit 48-Ball µBGA* Chip Size Package
PRELIMINARY
9
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
The pin descriptions table details the usage of each device pin.
Table 2. 16-Mbit Smart 3 Advanced Boot Block Pin Descriptions
Symbol
A0–A20
DQ0–DQ7
Type
INPUT
Name and Function
ADDRESS INPUTS for memory addresses. Addresses are internally
latched during a program or erase cycle.
28F008B3: A[0-19], 28F016B3: A[0-20]
INPUT/OUTPUT
DATA INPUTS/OUTPUTS: Inputs array data on the second CE# and
WE# cycle during a Program command. Inputs commands to the
Command User Interface when CE# and WE# are active. Data is
internally latched. Outputs array, Intelligent Identifier and Status Register
data. The data pins float to tri-state when the chip is de-selected or the
outputs are disabled.
CE#
INPUT
CHIP ENABLE: Activates the internal control logic, input buffers,
decoders and sense amplifiers. CE# is active low. CE# high de-selects
the memory device and reduces power consumption to standby levels. If
CE# and RP# are high, but not at a CMOS high level, the standby
current will increase due to current flow through the CE# and RP# inputs.
OE#
INPUT
OUTPUT ENABLE: Enables the device’s outputs through the data
buffers during an array or status register read. OE# is active low.
WE#
INPUT
WRITE ENABLE: Controls writes to the Command Register and memory
array. WE# is active low. Addresses and data are latched on the rising
edge of the second WE# pulse.
RP#
INPUT
RESET/DEEP POWER-DOWN: Uses two voltage levels (V IL, VIH) to
control reset/deep power-down mode.
When RP# is at logic low, the device is in reset/deep power-down
mode, which drives the outputs to High-Z, resets the Write State
Machine, and draws minimum current.
When RP# is at logic high, the device is in standard operation.
When RP# transitions from logic-low to logic-high, the device defaults to
the read array mode.
WP#
INPUT
WRITE PROTECT: Provides a method for locking and unlocking the two
lockable parameter blocks.
When WP# is at logic low, the lockable blocks are locked,
preventing program and erase operations to those blocks. If a program
or erase operation is attempted on a locked block, SR.1 and either SR.4
[program] or SR.5 [erase] will be set to indicate the operation failed.
When WP# is at logic high, the lockable blocks are unlocked and
can be programmed or erased.
See Section 3.3 for details on write protection.
10
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 2. 16-Mbit Smart 3 Advanced Boot Block Pin Descriptions (Continued)
Symbol
VCCQ
Type
Name and Function
INPUT
OUTPUT VCC: Enables all outputs to be driven to 2.0V ±10% while the
VCC is at 2.7V. When this mode is used, the V CC should be regulated to
2.7V–2.85V to achieve lowest power operation (see Section 6.1: DC
Characteristics: VCCQ = 1.8V–2.2V).
This input may be tied directly to V CC (2.7V–3.6V).
See the DC Characteristics for further details.
VCC
DEVICE POWER SUPPLY: 2.7V–3.6V
VPP
PROGRAM/ERASE POWER SUPPLY: For erasing memory array
blocks or programming data in each block, a voltage of either 2.7V–3.6V
or 12V ± 5% must be applied to this pin. When V PP < VPPLK all blocks
are locked and protected against Program and Erase commands.
Applying 11.4V–12.6V to VPP can only be done for a maximum of 1000
cycles on the main blocks and 2500 cycles on the parameter blocks.
VPP may be connected to 12V for a total of 80 hours maximum (see
Section 3.4 for details).
GND
GROUND: For all internal circuitry. All ground inputs must be
connected.
NC
NO CONNECT: Pin may be driven or left floating.
2.2
Block Organization
The Smart 3 Advanced Boot Block is an
asymmetrically-blocked architecture that enables
system integration of code and data within a single
flash device. Each block can be erased
independently of the others up to 10,000 times. For
the address locations of each block, see the
memory maps in Figure 4 (top boot blocking) and
Figure 5 (bottom boot blocking).
2.2.1
PARAMETER BLOCKS
The Smart 3 Advanced Boot Block flash memory
architecture includes parameter blocks to facilitate
storage of frequently updated small parameters
(e.g., data that would normally be stored in an
EEPROM. By using software techniques, the byterewrite functionality of EEPROMs can be emulated.
Each 8-/16-Mbit device contains eight parameter
blocks of 8 Kbytes (8,192-bytes) each.
2.2.2
MAIN BLOCKS
After the parameter blocks, the remainder of the
array is divided into equal size main blocks for data
or code storage. Each 16-Mbit device contains
thirty-one 64-Kbyte (65,536-byte) blocks. Each
8-Mbit device contains fifteen 64-Kbyte blocks.
PRELIMINARY
11
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
16-Mbit Advanced Boot
Block
1FFFFF
1FE000
1FDFFF
1FC000
1FBFFF
1FA000
1F9FFF
1F8000
1F7FFF
1F6000
1F5FFF
1F4000
1F3FFF
1F2000
1F1FFF
1F0000
1EFFFF
1E0000
1DFFFF
1D0000
1CFFFF
1C0000
1BFFFF
1B0000
1AFFFF
1A0000
19FFFF
190000
18FFFF
180000
17FFFF
170000
16FFFF
160000
15FFFF
150000
14FFFF
140000
13FFFF
130000
12FFFF
120000
11FFFF
110000
10FFFF
100000
0FFFFF
0F0000
0EFFFF
0E0000
0DFFFF
0D0000
0CFFFF
0C0000
0BFFFF
0B0000
0AFFFF
0A0000
09FFFF
090000
08FFFF
080000
07FFFF
070000
06FFFF
060000
05FFFF
050000
04FFFF
040000
03FFFF
030000
02FFFF
020000
01FFFF
010000
00FFFF
000000
8-Mbit Advanced Boot
Block
FFFFF
FE000
FDFFF
FC000
FBFFF
8-Kbyte Block
38
8-Kbyte Block
37
8-Kbyte Block
36
8-Kbyte Block
35
8-Kbyte Block
34
8-Kbyte Block
33
8-Kbyte Block
32
8-Kbyte Block
31
64-Kbyte Block
30
64-Kbyte Block
E0000
DFFFF
29
64-Kbyte Block
28
64-Kbyte Block
D0000
CFFFF
C0000
BFFFF
27
64-Kbyte Block
26
64-Kbyte Block
25
64-Kbyte Block
24
64-Kbyte Block
23
64-Kbyte Block
22
64-Kbyte Block
21
64-Kbyte Block
50000
4FFFF
20
64-Kbyte Block
19
40000
3FFFF
64-Kbyte Block
18
64-Kbyte Block
17
64-Kbyte Block
16
64-Kbyte Block
15
64-Kbyte Block
14
64-Kbyte Block
13
64-Kbyte Block
12
64-Kbyte Block
11
64-Kbyte Block
10
64-Kbyte Block
9
64-Kbyte Block
8
64-Kbyte Block
7
64-Kbyte Block
6
64-Kbyte Block
5
64-Kbyte Block
4
64-Kbyte Block
3
64-Kbyte Block
2
64-Kbyte Block
1
0
64-Kbyte Block
FA000
F9FFF
F8000
F7FFF
F6000
F5FFF
F4000
F3FFF
F2000
F1FFF
F0000
EFFFF
B0000
AFFFF
A0000
9FFFF
90000
8FFFF
80000
7FFFF
70000
6FFFF
60000
5FFFF
30000
2FFFF
20000
1FFFF
10000
0FFFF
00000
8-Kbyte Block
22
8-Kbyte Block
21
8-Kbyte Block
20
8-Kbyte Block
19
8-Kbyte Block
18
8-Kbyte Block
17
8-Kbyte Block
16
8-Kbyte Block
15
64-Kbyte Block
14
64-Kbyte Block
13
64-Kbyte Block
12
64-Kbyte Block
11
64-Kbyte Block
10
64-Kbyte Block
9
64-Kbyte Block
8
64-Kbyte Block
7
64-Kbyte Block
6
64-Kbyte Block
5
64-Kbyte Block
4
64-Kbyte Block
3
64-Kbyte Block
2
64-Kbyte Block
0
1
64-Kbyte Block
0
0
0605-05
Figure 4. 8-/16-Mbit Advanced Boot Block Byte-Wide Top Boot Memory Maps
12
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
16-Mbit Advanced Boot
Block
1FFFFF
1F0000
1EFFFF
1E0000
1DFFFF
1D0000
1CFFFF
1C0000
1BFFFF
1B0000
1AFFFF
1A0000
19FFFF
190000
18FFFF
180000
17FFFF
170000
16FFFF
160000
15FFFF
150000
14FFFF
140000
13FFFF
130000
12FFFF
120000
11FFFF
110000
10FFFF
100000
0FFFFF
0F0000
0EFFFF
0E0000
0DFFFF
0D0000
0CFFFF
0C0000
0BFFFF
0B0000
0AFFFF
0A0000
09FFFF
090000
08FFFF
080000
07FFFF
070000
06FFFF
060000
05FFFF
050000
04FFFF
040000
03FFFF
030000
02FFFF
020000
01FFFF
010000
00FFFF
00E000
00DFFF
00C000
00BFFF
00A000
009FFF
008000
007FFF
006000
005FFF
004000
003FFF
002000
001FFF
000000
64-Kbyte Block
38
64-Kbyte Block
37
64-Kbyte Block
36
64-Kbyte Block
35
64-Kbyte Block
34
64-Kbyte Block
33
64-Kbyte Block
32
64-Kbyte Block
31
64-Kbyte Block
30
64-Kbyte Block
29
64-Kbyte Block
28
64-Kbyte Block
27
64-Kbyte Block
26
64-Kbyte Block
25
64-Kbyte Block
24
64-Kbyte Block
23
64-Kbyte Block
22
64-Kbyte Block
21
64-Kbyte Block
20
64-Kbyte Block
19
64-Kbyte Block
18
64-Kbyte Block
17
64-Kbyte Block
16
64-Kbyte Block
15
64-Kbyte Block
14
64-Kbyte Block
13
64-Kbyte Block
12
64-Kbyte Block
11
64-Kbyte Block
10
64-Kbyte Block
64-Kbyte Block
8-Kbyte Block
9
8
7
8-Kbyte Block
6
8-Kbyte Block
5
8-Mbit Advanced Boot
Block
FFFFF
F0000
EFFFF
E0000
DFFFF
D0000
CFFFF
C0000
BFFFF
B0000
AFFFF
A0000
9FFFF
90000
8FFFF
80000
7FFFF
70000
6FFFF
60000
5FFFF
50000
4FFFF
40000
3FFFF
30000
2FFFF
20000
1FFFF
10000
0FFFF
0E000
0DFFF
0C000
0BFFF
0A000
09FFF
8-Kbyte Block
4
8-Kbyte Block
3
08000
07FFF
8-Kbyte Block
2
06000
05FFF
8-Kbyte Block
0
1
8-Kbyte Block
0
04000
03FFF
02000
01FFF
00000
64-Kbyte Block
22
64-Kbyte Block
21
64-Kbyte Block
20
64-Kbyte Block
19
64-Kbyte Block
18
64-Kbyte Block
17
64-Kbyte Block
16
64-Kbyte Block
15
64-Kbyte Block
14
64-Kbyte Block
13
64-Kbyte Block
12
64-Kbyte Block
11
64-Kbyte Block
10
64-Kbyte Block
9
64-Kbyte Block
8
8-Kbyte Block
7
8-Kbyte Block
6
8-Kbyte Block
5
8-Kbyte Block
4
8-Kbyte Block
3
8-Kbyte Block
2
8-Kbyte Block
1
0
8-Kbyte Block
0
0605-06
Figure 5. 8-/16-Mbit Advanced Boot Block Byte-Wide Bottom Boot Memory Maps
PRELIMINARY
13
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
3.0
PRINCIPLES OF OPERATION
Flash memory combines EEPROM functionality
with in-circuit electrical program and erase
capability. The Smart 3 Advanced Boot Block flash
memory family utilizes a Command User Interface
(CUI) and automated algorithms to simplify program
and erase operations. The CUI allows for 100%
CMOS-level control inputs, fixed power supplies
during erasure and programming, and maximum
EEPROM compatibility.
When VPP < VPPLK, the device will only execute the
following commands successfully: Read Array,
Read Status Register, Clear Status Register and
Read Intelligent Identifier. The device provides
standard EEPROM read, standby and output
disable operations. Manufacturer identification and
device identification data can be accessed through
the CUI. In addition, 2.7V or 12V on VPP allows
program and erase of the device. All functions
associated with altering memory contents, namely
program and erase, are accessible via the CUI.
The internal Write State Machine (WSM) completely
automates program and erase operations while the
CUI signals the start of an operation and the status
register reports status. The CUI handles the WE#
interface to the data and address latches, as well
as system status requests during WSM operation.
3.1
Bus Operation
Smart 3 Advanced Boot Block flash memory
devices read, program and erase in-system via the
local CPU or microcontroller. All bus cycles to or
from the flash memory conform to standard
microcontroller bus cycles. Four control pins dictate
the data flow in and out of the flash component:
CE#, OE#, WE# and RP#. These bus operations
are summarized in Table 3.
Table 3. Bus Operations for Byte-Wide Mode
Mode
Notes
RP#
CE#
OE#
WE#
WP#
A0
VPP
DQ0–7
1,2,3
VIH
VIL
VIL
VIH
X
X
X
DOUT
Output Disable
2
VIH
VIL
VIH
VIH
X
X
X
High Z
Standby
2
VIH
VIH
X
X
X
X
X
High Z
Deep Power-Down
2,9
VIL
X
X
X
X
X
X
High Z
Intelligent Identifier (Mfr.)
2,4
VIH
VIL
VIL
VIH
X
VIL
X
89 H
Intelligent Identifier (Dvc.)
2,4,5
VIH
VIL
VIL
VIH
X
VIH
X
See Table 5
2,6,7,
8
VIH
VIL
VIH
VIL
X
X
VPPH
DIN
Read
Write
NOTES:
1. Refer to DC Characteristics.
2. X must be VIL, VIH for control pins and addresses, VPPLK , VPPH1 or VPPH2 for VPP.
3. See DC Characteristics for VPPLK, VPPH1, VPPH2 voltages.
4. Manufacturer and device codes may also be accessed via a CUI write sequence, A1–A20 = X
5. See Table 5 for device IDs.
6. Refer to Table 6 for valid DIN during a write operation.
7. Command writes for block erase or byte program are only executed when VPP = VPPH1 or VPPH2.
8. To program or erase the lockable blocks, hold WP# at VIH. See Section 3.3.
9. RP# must be at GND ± 0.2V to meet the maximum deep power-down current specified.
14
PRELIMINARY
E
3.1.1
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
READ
The flash memory has three read modes available:
read array, read identifier, and read status. These
modes are accessible independent of the VPP
voltage. The appropriate read mode command must
be issued to the CUI to enter the corresponding
mode. Upon initial device power-up or after exit
from deep power-down mode, the device
automatically defaults to read array mode.
CE# and OE# must be driven active to obtain data
at the outputs. CE# is the device selection control;
when active it enables the flash memory device.
OE# is the data output (DQ0–DQ7) control and it
drives the selected memory data onto the I/O bus.
For all read modes, WE# and RP# must be at VIH.
Figure 14 illustrates a read cycle.
3.1.2
OUTPUT DISABLE
With OE# at a logic-high level (VIH), the device
outputs are disabled. Output pins DQ0–DQ7 are
placed in a high-impedance state.
3.1.3
STANDBY
Deselecting the device by bringing CE# to a logichigh level (VIH) places the device in standby mode,
which substantially reduces device power
consumption. In standby, outputs DQ0–DQ7 are
placed in a high-impedance state independent of
OE#. If deselected during program or erase
operation, the device continues to consume active
power until the program or erase operation is
complete.
3.1.4
DEEP POWER-DOWN/RESET
RP# at VIL initiates the deep power-down mode,
sometimes referred to as reset mode.
From read mode, RP# going low for time tPLPH
accomplishes the following:
1.
deselects the memory
2.
places output drivers in a high-impedance
state
After return from power-down, a time tPHQV is
required until the initial memory access outputs are
PRELIMINARY
valid. A delay (tPHWL or tPHEL) is required after
return from power-down before a write sequence
can be initiated. After this wake-up interval, normal
operation is restored. The CUI resets to read array
mode, and the status register is set to 80H (ready).
If RP# is taken low for time tPLPH during a program
or erase operation, the operation will be aborted
and the memory contents at the aborted location
are no longer valid. After returning from an aborted
operation, time tPHQV or tPHWL/tPHEL must be met
before a read or write operation is initiated
respectively.
3.1.5
WRITE
A write is any command that alters the contents of
the memory array. There are two write commands:
Program (40H) and Erase (20H). Writing either of
these commands to the internal Command User
Interface (CUI) initiates a sequence of internallytimed functions that culminate in the completion of
the requested task (unless that operation is aborted
by either RP# being driven to VIL for of tPLRH or an
appropriate suspend command).
The Command User Interface does not occupy an
addressable memory location. Instead, commands
are written into the CUI using standard
microprocessor write timings when WE# and CE#
are low, OE# = VIH, and the proper address and
data (command) are presented. The command is
latched on the rising edge of the first WE# or CE#
pulse, whichever occurs first. Figure 15 illustrates a
write operation.
Device operations are selected by writing specific
commands into the CUI. Table 4 defines the
available commands. Appendix B provides detailed
information on moving between the different modes
of operation.
3.2
Modes of Operation
The flash memory has three read modes and two
write modes. The read modes are read array, read
identifier, and read status. The write modes are
program and block erase. Three additional mode
(erase suspend to program, erase suspend to read
and program suspend to read) are available only
during suspended operations. These modes are
15
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
reached using the commands summarized in Table
4. A comprehensive chart showing the state
transitions is in Appendix B.
When the device is in the read array mode, four
control signals must be controlled to obtain data at
the outputs.
3.2.1
•
READ ARRAY
When RP# transitions from VIL (reset) to VIH, the
device will be in the read array mode and will
respond to the read control inputs (CE#, address
inputs, and OE#) without any commands being
written to the CUI.
WE# must be logic high (VIH)
•
CE# must be logic low (VIL)
•
OE# must be logic low (VIL)
•
RP# must be logic high (VIH)
In addition, the address of the desired location must
be applied to the address pins.
If the device is not in read array mode, as would be
the case after a program or erase operation, the
Read Array command (FFH) must be written to the
CUI before array reads can take place.
Table 4. Command Codes and Descriptions
Code
Device Mode
00
Invalid/
Reserved
FF
Read Array
Places the device in read array mode, such that array data will be output on the
data pins.
40
Program
Set-Up
This is a two-cycle command. The first cycle prepares the CUI for a program
operation. The second cycle latches addresses and data information and
initiates the WSM to execute the Program algorithm. The flash outputs status
register data when CE# or OE# is toggled. A Read Array command is required
after programming to read array data. See Section 3.2.4.
10
Description
Unassigned commands that should not be used. Intel reserves the right to
redefine these codes for future functions.
Alternate
(See 40H/Program Set-Up)
Program Set-Up
20
Erase
Set-Up
Prepares the CUI for the Erase Confirm command. If the next command is not
an Erase Confirm command, then the CUI will (a) set both SR.4 and SR.5 of the
status register to a “1,” (b) place the device into the read status register mode,
and (c) wait for another command. See Section 3.2.5.
D0
Program
Resume
If the previous command was an Erase Set-Up command, then the CUI will
close the address and data latches, and begin erasing the block indicated on the
address pins. If a program or erase operation was previously suspended, this
command will resume that operation.
Erase Resume/
Erase Confirm
During program/erase, the device will respond only to the Read Status Register,
Program Suspend/Erase Suspend commands and will output status register
data when CE# or OE# is toggled.
16
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 4. Command Codes and Descriptions (Continued)
Code
Device Mode
Description
B0
Program
Suspend
Issuing this command will begin to suspend the currently executing
program/erase operation. The status register will indicate when the operation
has been successfully suspended by setting either the program suspend (SR.2)
or erase suspend (SR.6) and the WSM Status bit (SR.7) to a “1” (ready). The
WSM will continue to idle in the SUSPEND state, regardless of the state of all
input control pins except RP#, which will immediately shut down the WSM and
the remainder of the chip if it is driven to V IL. See Sections 3.2.4.1 and 3.2.5.1.
Erase
Suspend
70
Read Status
Register
This command places the device into read status register mode. Reading the
device will output the contents of the status register, regardless of the address
presented to the device. The device automatically enters this mode after a
program or erase operation has been initiated. See Section 3.2.3.
50
Clear Status
Register
The WSM can set the Block Lock Status (SR.1) , V PP Status (SR.3), Program
Status (SR.4), and Erase Status (SR.5) bits in the status register to “1,” but it
cannot clear them to “0.” Issuing this command clears those bits to “0.”
90
Intelligent
Identifier
Puts the device into the intelligent identifier read mode, so that reading the
device will output the manufacturer and device codes (A 0 = 0 for manufacturer,
A0 = 1 for device, all other address inputs are ignored). See Section 3.2.2.
NOTE:
See Appendix B for mode transition information.
3.2.2
READ INTELLIGENT IDENTIFIER
To read the manufacturer and device codes, the
device must be in read intelligent identifier mode,
which can be reached by writing the Intelligent
Identifier command (90H). Once in intelligent
identifier mode, A0 = 0 outputs the manufacturer’s
identification code and A0 = 1 outputs the device
code. See Table 5 for product signatures. To return
to read array mode, write the Read Array command
(FFH).
Table 5. Intelligent Identifier Table
3.2.3
READ STATUS REGISTER
The device status register indicates when a
program or erase operation is complete, and the
success or failure of that operation. To read the
status register issue the Read Status Register
(70H) command to the CUI. This causes all
subsequent read operations to output data from the
status register until another command is written to
the CUI. To return to reading from the array, issue
the Read Array (FFH) command.
The status register bits are output on DQ0–DQ7.
Size
Mfr. ID
Device ID
-T
-B
(Top Boot) (Bottom
Boot)
8-Mbit
89H
D2H
D3H
16-Mbit
89H
D0H
D1H
PRELIMINARY
The contents of the status register are latched on
the falling edge of OE# or CE#. This prevents
possible bus errors which might occur if status
register contents change while being read. CE# or
OE# must be toggled with each subsequent status
read, or the status register will not indicate
completion of a program or erase operation.
17
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
When the WSM is active, bit 7 (SR.7) of the status
register will indicate the status of the WSM; the
remaining bits in the status register indicate
whether or not the WSM was successful in
performing the desired operation (see Table 7).
3.2.3.1
Clearing the Status Register
The WSM sets status bits 1 through 7 to “1,” and
clears bits 2, 6 and 7 to “0,” but cannot clear status
bits 1 or 3 through 5 to “0.” Because bits 1, 3, 4,
and 5 indicate various error conditions, these bits
can only be cleared by the controlling CPU through
the use of the Clear Status Register (50H)
command. By allowing the system software to
control the resetting of these bits, several
operations may be performed (such as cumulatively
programming several addresses or erasing multiple
blocks in sequence) before reading the status
register to determine if an error occurred during that
series. Clear the Status Register before beginning
another command or sequence. Note, again, that
the Read Array command must be issued before
data can be read from the memory array.
3.2.4
PROGRAM MODE
Programming is executed using a two-write
sequence. The Program Setup command (40H) is
written to the CUI followed by a second write which
specifies the address and data to be programmed.
The WSM will execute the following sequence of
internally timed events:
1. Program the desired bits of the addressed
memory.
2. Verify that the desired bits are sufficiently
programmed.
Programming of the memory results in specific bits
within an address location being changed to a “0.” If
the user attempts to program “1”s, there will be no
change of the memory cell contents and no error
occurs.
The status register indicates programming status:
while the program sequence is executing, bit 7 of
the status register is a “0.” The status register can
be polled by toggling either CE# or OE#. While
programming, the only valid commands are Read
Status Register, Program Suspend, and Program
Resume.
18
E
When programming is complete, the Program
Status bits should be checked. If the programming
operation was unsuccessful, bit SR.4 of the status
register is set to indicate a program failure. If SR.3
is set then VPP was not within acceptable limits, and
the WSM did not execute the program command. If
SR.1 is set, a program operation was attempted to
a locked block and the operation was aborted.
The status register should be cleared before
attempting the next operation. Any CUI instruction
can follow after programming is completed;
however, to prevent inadvertent status register
reads, be sure to reset the CUI to read array mode.
3.2.4.1
Suspending and Resuming
Program
The Program Suspend command allows program
suspension in order to read data in other locations
of memory. Once the programming process starts,
writing the Program Suspend command to the CUI
requests that the WSM suspend the program
sequence (at predetermined points in the program
algorithm). The device continues to output status
register data after the Program Suspend command
is written. Polling status register bits SR.7 and SR.2
will determine when the program operation has
been suspended (both will be set to “1”).
tWHRH1/tEHRH1 specify the program suspend latency.
A Read Array command can now be written to the
CUI to read data from blocks other than that which
is suspended. The only other valid commands,
while program is suspended, are Read Status
Register and Program Resume. After the Program
Resume command is written to the flash memory,
the WSM will continue with the program process
and status register bits SR.2 and SR.7 will
automatically be cleared. After the Program
Resume command is written, the device
automatically outputs status register data when
read (see Figure 7, Program Suspend/Resume
Flowchart). VPP must remain at the same VPP level
used for program while in program suspend mode.
RP# must also remain at V IH.
3.2.4.2
VPP Supply Voltage during
Program
VPP supply voltage considerations are outlined in
Section 3.4.
PRELIMINARY
E
3.2.5
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
ERASE MODE
To erase a block, write the Erase Set-up and Erase
Confirm commands to the CUI, along with an
address identifying the block to be erased. This
address is latched internally when the Erase
Confirm command is issued. Block erasure results
in all bits within the block being set to “1.” Only one
block can be erased at a time.
The WSM will execute the following sequence of
internally timed events to:
1. Program all bits within the block to “0.”
2. Verify that all bits within the block are
sufficiently programmed to “0.”
3. Erase all bits within the block to “1.”
4. Verify that all bits within the block are
sufficiently erased.
While the erase sequence is executing, bit 7 of the
status register is a “0.”
When the status register indicates that erasure is
complete, check the Erase Status bit to verify that
the erase operation was successful. If the Erase
operation was unsuccessful, SR.5 of the status
register will be set to a “1,” indicating an erase
error. If VPP was not within acceptable limits after
the Erase Confirm command was issued, the WSM
will not execute the erase sequence; instead, SR.5
of the status register is set to indicate an erase
error, and SR.3 is set to a “1” to identify that VPP
supply voltage was not within acceptable limits.
3.2.5.1
Suspending and Resuming Erase
Since an erase operation requires on the order of
seconds to complete, an Erase Suspend command
is provided to allow erase-sequence interruption in
order to read data from or program data to another
block in memory. Once the erase sequence is
started, writing the Erase Suspend command to the
CUI requests that the WSM pause the erase
sequence at a predetermined point in the erase
algorithm. The status register will indicate if/when
the erase operation has been suspended.
A Read Array/Program command can now be
written to the CUI in order to read/write data from/to
blocks other than that which is suspended. The
Program
command
can
subsequently
be
suspended to read yet another array location. The
only valid commands while erase is suspended are
Erase Resume, Program, Program Resume, Read
Array, or Read Status Register.
During erase suspend mode, the chip can be
placed in a pseudo-standby mode by taking CE# to
VIH. This reduces active current consumption.
Erase Resume continues the erase sequence when
CE# = VIL. As with the end of a standard erase
operation, the status register must be read and
cleared before the next instruction is issued.
3.2.5.2
VPP Supply Voltage during Erase
VPP supply voltage considerations are outlined in
Section 3.4.
After an erase operation, clear the Status Register
(50H) before attempting the next operation. Any
CUI instruction can follow after erasure is
completed; however, to prevent inadvertent status
register reads, it is advisable to reset the flash to
read array after the erase is complete.
PRELIMINARY
19
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 6. Command Bus Definitions
First Bus Cycle
Command
Second Bus Cycle
Notes
Oper
Addr
Data
Oper
Addr
Data
5
Write
X
FFH
2,3,5
Write
X
90H
Read
IA
ID
Read Status Register
5
Write
X
70H
Read
X
SRD
Clear Status Register
5
Write
X
50H
Write (Program)
4,5
Write
X
40H
Write
PA
PD
Alternate Write (Program)
4,5
Write
X
10H
Write
PA
PD
Block Erase/Confirm
5
Write
X
20H
Write
BA
D0H
Program/Erase Suspend
5
Write
X
B0H
Program/Erase Resume
5
Write
X
D0H
Read Array
Intelligent Identifier
ADDRESS
DATA
BA = Block Address
IA = Identifier Address
PA = Program Address
X = Don’t Care
SRD = Status Register Data
ID = Identifier Data
PD = Program Data
NOTES:
1. Bus operations are defined in Table 3.
2. A0 = 0 for manufacturer code, A0 = 1 for device code.
3. Following the Intelligent Identifier command, two read operations access manufacturer and device codes.
4. Either 40H or 10H command is valid.
20
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 7. Status Register Bit Definition
WSMS
ESS
ES
PS
VPPS
PSS
BLS
R
7
6
5
4
3
2
1
0
NOTES:
SR.7 WRITE STATE MACHINE STATUS
1 = Ready
(WSMS)
0 = Busy
Check Write State Machine bit first to determine
Byte Program or Block Erase completion, before
checking Program or Erase Status bits.
SR.6 = ERASE-SUSPEND STATUS (ESS)
1 = Erase Suspended
0 = Erase In Progress/Completed
When Erase Suspend is issued, WSM halts
execution and sets both WSMS and ESS bits to
“1.” ESS bit remains set to “1” until an Erase
Resume command is issued.
SR.5 = ERASE STATUS (ES)
1 = Error In Block Erasure
0 = Successful Block Erase
When this bit is set to “1,” WSM has applied the
max. number of erase pulses to the block and is
still unable to verify successful block erasure.
SR.4 = PROGRAM STATUS (PS)
1 = Error in Byte Program
0 = Successful Byte Program
When this bit is set to “1,” WSM has attempted
but failed to program a byte.
SR.3 = VPP STATUS (VPPS)
1 = VPP Low Detect, Operation Abort
0 = VPP OK
The VPP Status bit does not provide continuous
indication of VPP level. The WSM interrogates VPP
level only after the Program or Erase command
sequences have been entered, and informs the
system if V PP has not been switched on. The VPP
is also checked before the operation is verified by
the WSM. The VPP Status bit is not guaranteed to
report accurate feedback between VPPLK and
VPPH.
SR.2 = PROGRAM SUSPEND STATUS (PSS)
1 = Program Suspended
0 = Program in Progress/Completed
When Program Suspend is issued, WSM halts
execution and sets both WSMS and PSS bits to
“1.” PSS bit remains set to “1” until a Program
Resume command is issued.
SR.1 = Block Lock Status
1 = Program/Erase attempted on locked
block; Operation aborted
0 = No operation to locked blocks
If a program or erase operation is attempted to
one of the locked blocks, this bit is set by the
WSM. The operation specified is aborted and the
device is returned to read status mode.
SR.0 = RESERVED FOR FUTURE
ENHANCEMENTS (R)
These bits are reserved for future use and should
be masked out when polling the Status Register.
PRELIMINARY
21
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Start
Write 40H
Bus Operation
Command
Write
Program Setup
Write
Program
Program Address/Data
Data = 40H
Data = Data to Program
Addr = Location to Program
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Read
Read Status Register
Check SR.7
1 = WSM Ready
0 = WSM Busy
Standby
Repeat for subsequent programming operations.
No
SR.7 = 1?
Comments
SR Full Status Check can be done after each program or after a sequence of
program operations.
Yes
Write FFH after the last program operation to reset device to read array mode.
Full Status
Check if Desired
Program Complete
FULL STATUS CHECK PROCEDURE
Read Status Register
Data (See Above)
Bus Operation
1
SR.3 =
0
VPP Range Error
Programming Error
0
1
Comments
Standby
Check SR.3
1 = VPP Low Detect
Standby
Check SR.4
1 = VPP Program Error
Standby
Check SR.1
1 = Attempted Program to
Locked Block - Program
Aborted
1
SR.4 =
SR.1 =
Command
SR.3 MUST be cleared, if set during a program attempt, before further
attempts are allowed by the Write State Machine.
Attempted Program to
Locked Block - Aborted
SR.1, SR.3 and SR.4 are only cleared by the Clear Staus Register Command,
in cases where multiple bytes are programmed before full status is checked.
0
Program Successful
If an error is detected, clear the status register before attempting retry or other
error recovery.
0605-07
Figure 6. Automated Byte Programming Flowchart
22
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Start
Bus Operation
Command
Write
Program Suspend
Write B0H
Read Status Register
Standby
Check SR.7
1 = WSM Ready
0 = WSM Busy
Standby
Check SR.2
1 = Program Suspended
0 = Program Completed
0
1
0
SR.2 =
Program Completed
1
Data = B0H
Addr = X
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Addr = X
Read
SR.7 =
Comments
Write
Read Array
Data = FFH
Addr = X
Read array data from block
other than the one being
programmed.
Read
Write FFH
Write
Program Resume
Data = D0H
Addr = X
Read Array Data
No
Done
Reading
Yes
Write D0H
Write FFH
Program Resumed
Read Array Data
0605-08
Figure 7. Program Suspend/Resume Flowchart
PRELIMINARY
23
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Start
Bus Operation
Write 20H
Write D0H and
Block Address
Command
Write
Erase Setup
Write
Erase Confirm
Data = D0H
Addr = Within Block to Be
Erased
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Read
Read Status Register
Suspend
Erase Loop
0
SR.7 =
No
Suspend Erase
Comments
Data = 20H
Addr = Within Block to Be
Erased
Check SR.7
1 = WSM Ready
0 = WSM Busy
Standby
Yes
Repeat for subsequent block erasures.
Full Status Check can be done after each block erase or after a sequence of
block erasures.
1
Full Status
Check if Desired
Write FFH after the last write operation to reset device to read array mode.
Block Erase Complete
FULL STATUS CHECK PROCEDURE
Read Status Register
Data (See Above)
Bus Operation
1
SR.3 =
0
Command
Standby
Check SR.3
1 = VPP Low Detect
Standby
Check SR.4,5
Both 1 = Command Sequence
Error
Standby
Check SR.5
1 = Block Erase Error
Standby
Check SR.1
1 = Attempted Erase of
Locked Block - Erase Aborted
VPP Range Error
1
SR.4,5 =
Command Sequence
Error
0
1
SR.5 =
Block Erase Error
Comments
SR. 1 and 3 MUST be cleared, if set during an erase attempt, before further
attempts are allowed by the Write State Machine.
0
1
SR.1 =
0
Attempted Erase of
Locked Block - Aborted
SR.1, 3, 4, 5 are only cleared by the Clear Staus Register Command, in cases
where multiple bytes are erased before full status is checked.
If an error is detected, clear the status register before attempting retry or other
error recovery.
Block Erase
Successful
0605-09
Figure 8. Automated Block Erase Flowchart
24
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Start
Bus Operation
Command
Write
Erase Suspend
Write B0H
Read Status Register
Standby
Check SR.7
1 = WSM Ready
0 = WSM Busy
Standby
Check SR.6
1 = Erase Suspended
0 = Erase Completed
0
1
0
SR.6 =
Erase Completed
1
Data = B0H
Addr = X
Status Register Data Toggle
CE# or OE# to Update Status
Register Data
Addr = X
Read
SR.7 =
Comments
Write
Read Array
Data = FFH
Addr = X
Read
Read array data from block
other than the one being
erased.
Program
Program data to block other
than the one being erased.
Write FFH/40H
Read Array Data/
Program Array
Done
Reading and/or
Programming
Write
Erase Resume
Data = D0H
Addr = X
No
Yes
Write D0H
Write FFH
Erase Resumed
Read Array Data
0605-010
Figure 9. Erase Suspend/Resume Flowchart
PRELIMINARY
25
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
3.3
Block Locking
The Smart 3 Advanced Boot Block flash memory
architecture features
two
hardware-lockable
parameter blocks so that the kernel code for the
system can be kept secure while other parameter
blocks are programmed or erased as necessary.
3.3.1
VPP = VIL FOR COMPLETE
PROTECTION
The VPP programming voltage can be held low for
complete write protection of all blocks in the flash
device. When VPP is below VPPLK, any program or
erase operation will result in a error, prompting the
corresponding Status Register bit (SR.3) to be set.
3.3.2
WP# = VIH FOR BLOCK UNLOCKING
WP# = VIH unlocks all lockable blocks.
These blocks can now be programmed or erased.
Note that RP# does not override WP# locking as in
previous Boot Block devices. WP# controls all block
locking and VPP provides protection against
spurious writes. Table 8 defines the write protection
methods.
3.4
VPP Program and Erase
Voltages
Intel’s Smart 3 products provide in-system
programming and erase at 2.7V–3.6V VPP. For
customers requiring fast programming in their
manufacturing environment, Smart 3 Advanced
Boot Block includes an additional low-cost,
backward-compatible 12V programming feature.
26
Table 8. Write Protection Truth Table for
Advanced Boot Block Flash Memory Family
VPP
WP#
RP#
Write Protection
Provided
X
X
VIL
All Blocks Locked
VIL
X
VIH
All Blocks Locked
≥ VPPLK
VIL
VIH
Lockable Blocks
Locked
≥ VPPLK
VIH
VIH
All Blocks Unlocked
WP# = VIL FOR BLOCK LOCKING
The lockable blocks are locked when WP# = VIL;
any program or erase operation to a locked block
will result in an error, which will be reflected in the
status register. For top configuration, the top two
parameter blocks (blocks #37 and #38 for the
16-Mbit, and blocks #21 and #22 for the 8-Mbit) are
lockable. For the bottom configuration, the bottom
two parameter blocks (blocks #0 and #1 for 8-/16Mbit) are lockable. Unlocked blocks can be
programmed or erased normally (unless VPP is
below VPPLK).
3.3.3
The 12V VPP mode enhances programming
performance during the short period of time typically
found in manufacturing processes; however, it is
not intended for extended use. 12V may be applied
to VPP during program and erase operations for a
maximum of 1000 cycles on the main blocks and
2500 cycles on the parameter blocks. VPP may be
connected to 12V for a total of 80 hours maximum.
Stressing the device beyond these limits may cause
permanent damage.
3.5
Power Consumption
While in operation, the flash device consumes
active power. However, Intel flash devices have a
three-tiered approach to power savings that can
significantly reduce overall system power
consumption. The Automatic Power Savings (APS)
feature reduces power consumption when the
device is idle. If the CE# is deasserted, the flash
enters its standby mode, where current
consumption is even lower. If RP# = VIL the flash
enters a deep power-down mode, where current is
at a minimum. The combination of these features
can minimize overall memory power consumption,
and therefore, overall system power consumption.
3.5.1
ACTIVE POWER
With CE# at a logic-low level and RP# at a logichigh level, the device is in the active mode. Refer to
the DC Characteristics tables for ICC current values.
Active power is the largest contributor to overall
system power consumption. Minimizing the active
current could have a profound effect on system
power consumption, especially for battery-operated
devices.
PRELIMINARY
E
3.5.2
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
AUTOMATIC POWER SAVINGS (APS)
Automatic Power Savings provides low-power
operation during active mode. Power Reduction
Control (PRC) circuitry allows the flash to put itself
into a low current state when not being accessed.
After data is read from the memory array, PRC
logic controls the device’s power consumption by
entering the APS mode where typical ICC current is
comparable to ICCS. The flash stays in this static
state with outputs valid until a new location is read.
APS reduces active current to standby current
levels for 2.7V–3.6V CMOS input levels.
3.5.3
STANDBY POWER
With CE# at a logic-high level (VIH) and the CUI in
read mode, the flash memory is in standby mode,
which disables much of the device’s circuitry and
substantially reduces power consumption. Outputs
(DQ0–DQ7) are placed in a high-impedance state
independent of the status of the OE# signal. If CE#
transitions to a logic-high level during erase or
program operations, the device will continue to
perform the operation and consume corresponding
active power until the operation is completed.
System engineers should analyze the breakdown of
standby time versus active time and quantify the
respective power consumption in each mode for
their specific application. This will provide a more
accurate measure of application-specific power and
energy requirements.
3.5.4
DEEP POWER-DOWN MODE
The deep power-down mode of the Smart 3
Advanced Boot Block products switches the device
into a low power savings mode, which is especially
important for battery-based devices. This mode is
activated when RP# = VIL. (GND ± 0.2V).
During read modes, RP# going low de-selects the
memory and places the output drivers in a high
impedance state. Recovery from the deep powerdown state, requires a minimum time equal to tPHQV
(see AC Characteristics table).
During program or erase modes, RP# transitioning
low will abort the operation, but the memory
contents of the address being programmed or the
block being erased are no longer valid as the data
integrity has been compromised by the abort.
PRELIMINARY
During deep power-down, all internal circuits are
switched to a low power savings mode (RP#
transitioning to VIL or turning off power to the device
clears the status register).
3.6
Power-Up/Down Operation
The device is protected against accidental block
erasure or programming during power transitions.
Power supply sequencing is not required, since the
device is indifferent as to which power supply, VPP
or VCC, powers-up first.
3.6.1
RP# CONNECTED TO SYSTEM
RESET
The use of RP# during system reset is important
with automated program/erase devices since the
system expects to read from the flash memory
when it comes out of reset. If a CPU reset occurs
without a flash memory reset, proper CPU
initialization will not occur because the flash
memory may be providing status information
instead of array data. Intel recommends connecting
RP# to the system CPU RESET# signal to allow
proper CPU/flash initialization following system
reset.
System designers must guard against spurious
writes when VCC voltages are above VLKO and VPP
is active. Since both WE# and CE# must be low for
a command write, driving either signal to VIH will
inhibit writes to the device. The CUI architecture
provides additional protection since alteration of
memory contents can only occur after successful
completion of the two-step command sequences.
The device is also disabled until RP# is brought to
VIH, regardless of the state of its control inputs. By
holding the device in reset (RP# connected to
system PowerGood) during power-up/down, invalid
bus conditions during power-up can be masked,
providing yet another level of memory protection.
3.6.2
VCC, VPP AND RP# TRANSITIONS
The CUI latches commands as issued by system
software and is not altered by VPP or CE#
transitions or WSM actions. Its default state upon
power-up, after exit from deep power-down mode or
after VCC transitions above VLKO (Lockout voltage),
is read array mode.
27
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
E
Refer to AP-617 Additional Flash Data Protection
Using VPP, RP#, and WP# for a circuit-level
description of how to implement the protection
schemes discussed in Section 3.5.
Transient current magnitudes depend on the device
outputs’ capacitive and inductive loading. Two-line
control and proper decoupling capacitor selection
will suppress these transient voltage peaks. Each
flash device should have a 0.1 µF ceramic
capacitor connected between each VCC and GND,
and between its VPP and GND. These highfrequency, inherently low-inductance capacitors
should be placed as close as possible to the
package leads.
3.7
3.7.1
After any program or block erase operation is
complete (even after VPP transitions down to
VPPLK), the CUI must be reset to read array mode
via the Read Array command if access to the flash
memory array is desired.
Power Supply Decoupling
Flash memory’s power switching characteristics
require careful device decoupling. System
designers should consider three supply current
issues:
1. Standby current levels (ICCS)
2. Active current levels (I CCR)
3. Transient peaks produced by falling and rising
edges of CE#.
28
VPP TRACE ON PRINTED CIRCUIT
BOARDS
Designing for in-system writes to the flash memory
requires special consideration of the VPP power
supply trace by the printed circuit board designer.
The VPP pin supplies the flash memory cells current
for programming and erasing. VPP trace widths and
layout should be similar to that of VCC. Adequate
VPP supply traces, and decoupling capacitors
placed adjacent to the component, will decrease
spikes and overshoots.
PRELIMINARY
E
4.0
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
ABSOLUTE MAXIMUM
RATINGS*
Extended Operating Temperature
During Read ............................ –40°C to +85°C
During Block Erase
and Program............................ –40°C to +85°C
Temperature Under Bias ......... –40°C to +85°C
Storage Temperature................... –65°C to +125°C
Voltage on Any Pin
(except VCC, VCCQ and VPP)
with Respect to GND ............... –0.5V to +5.0V1
NOTICE: This datasheet contains preliminary information on
products in production. The specifications are subject to
change without notice. Verify with your local Intel Sales
office that you have the latest datasheet before finalizing a
design.
* WARNING: Stressing the device beyond the "Absolute
Maximum Ratings" may cause permanent damage. These
are stress ratings only. Operation beyond the "Operating
Conditions" is not recommended and extended exposure
beyond the "Operating Conditions" may effect device
reliability.
NOTES:
1.
Minimum DC voltage is –0.5V on input/output pins.
During transitions, this level may undershoot to –2.0V
for periods < 20 ns. Maximum DC voltage on
input/output pins is VCC + 0.5V which, during
transitions, may overshoot to VCC + 2.0V for periods <
20 ns.
Maximum DC voltage on VPP may overshoot to +14.0V
for periods < 20 ns.
Output shorted for no more than one second. No more
than one output shorted at a time.
VPP Program voltage is normally 2.7V–3.6V.
Connection to supply of 11.4V–12.6V can only be done
for 1000 cycles on the main blocks and 2500 cycles on
the parameter blocks during program/erase. VPP may
be connected to 12V for a total of 80 hours maximum.
See Section 3.4 for details.
VPP Voltage (for Block
Erase and Program)
with Respect to GND .........–0.5V to +13.5V1,2,4
VCC and VCCQ Supply Voltage
with Respect to GND ............... –0.2V to +5.0V1
Output Short Circuit Current...................... 100 mA3
2.
3.
4.
5.0
OPERATING CONDITIONS (VCCQ = 2.7V–3.6V)
Table 9. Temperature and Voltage Operating Conditions4
Symbol
Parameter
Notes
Min
Max
Units
–40
+85
°C
TA
Operating Temperature
VCC
2.7V–3.6V VCC Supply Voltage
1,4
2.7
3.6
Volts
VCCQ
2.7V–3.6V I/O Supply Voltage
1,2,4
2.7
3.6
Volts
VPP1
Program and Erase Voltage
4
2.7
3.6
Volts
3
11.4
12.6
Volts
5
10,000
VPP2
Cycling
Block Erase Cycling
Cycles
NOTES:
1. See DC Characteristics tables for voltage range-specific specifications.
2. The voltage swing on the inputs, VIN is required to match VCCQ.
3. Applying VPP = 11.4V–12.6V during a program/erase can only be done for a maximum of 1000 cycles on the main blocks
and 2500 cycles on the parameter blocks. VPP may be connected to 12V for a total of 80 hours maximum. See section 3.4
for details.
4. VCC, VCCQ and VPP1 must share the same supply when all three are between 2.7V and 3.6V.
5. For operating temperatures of –25°C– +85°C the device is projected to have a minimum block erase cycling of 10,000 to
30,000 cycles.
PRELIMINARY
29
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
5.1
DC Characteristics: VCCQ = 2.7V–3.6V
Table 10. DC Characteristics
Sym
Parameter
Notes
VCC = 2.7V–3.6V
Typ
Unit
Test Conditions
Max
ILI
Input Load Current
1
± 1.0
µA
VCC = VCCMax = VCCQMax
VIN = VCCQ or GND
ILO
Output Leakage Current
1
± 10
µA
VCC = VCCMax = VCCQMax
VIN = VCCQ or GND
ICCS
VCC Standby Current
50
µA
CMOS INPUTS
VCC = VCCMax = VCCQMax
1,7
20
CE# = RP# = VCCQ
ICCD
VCC Deep Power-Down
Current
ICCR
VCC Read Current
1,7
1
10
µA
CMOS INPUTS
VCC = VCCMax = VCCQMax
VIN = VCCQ or GND
RP# = GND ± 0.2V
1,5,7
10
20
mA
CMOS INPUTS
VCC = VCCMax = VCCQMax
OE# = VIH , CE# =VIL
f = 5 MHz,
IOUT = 0 mA
Inputs = VIL or VIH
ICCW
ICCE
VCC Program Current
VCC Erase Current
1,4,7
1,4,7
8
20
mA
VPP = VPPH1 (3V)
Program in Progress
8
20
mA
VPP = VPPH2 (12V)
Program in Progress
8
20
mA
VPP = VPPH1 (3V)
Erase in Progress
8
20
mA
VPP = VPPH2 (12V)
Erase in Progress
ICCES
VCC Erase Suspend
Current
1,2,4,7
20
50
µA
CE# = VIH
Erase Suspend in Progress
ICCWS
VCC Program Suspend
Current
1,2,4,7
20
50
µA
CE# = VIH
Program Suspend in Progress
IPPD
VPP Deep Power-Down
Current
1
0.2
5
µA
RP# = GND ± 0.2V
IPPR
VPP Read Current
1
2
±50
µA
VPP ≤ VCC
30
PRELIMINARY
E
Sym
IPPW
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 10. DC Characteristics (Continued)
Parameter
VPP Program Current
Notes
1,4
VCC = 2.7V–3.6V
Typ
Max
15
40
Unit
mA
Test Conditions
VPP = VPPH1 (3V)
Program in Progress
10
25
mA
VPP = VPPH2 (12V)
Program in Progress
IPPE
VPP Erase Current
1,4
13
25
mA
VPP = VPPH1 (3V)
Erase in Progress
8
25
mA
VPP = VPPH2 (12V)
Erase in Progress
IPPES
VPP Erase Suspend
Current
1,4
50
200
µA
VPP = VPPH1 or VPPH2
Erase Suspend in Progress
IPPWS
VPP Program Suspend
Current
1,4
50
200
µA
VPP = VPPH1 or VPPH2
Program Suspend in Progress
PRELIMINARY
31
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 10. DC Characteristics (Continued)
Sym
Parameter
Notes
VCC = 2.7V–3.6V
Min
Max
Input Low Voltage
–0.4
0.4
VIH
Input High Voltage
VCCQ –
0.4V
VOL
Output Low Voltage
VOH
Output High Voltage
VPPLK
VPP Lock-Out Voltage
VPPH1
VPP during Prog/Erase
Operations
VIL
Test Conditions
V
V
0.10
VPPH2
Unit
V
VCC = VCCMin = VCCQMin
IOL = 100 µA
VCCQ –
0.1V
V
VCC = VCCMin = VCCQMin
IOH = –100 µA
3
1.5
V
Complete Write Protection
3
2.7
3.6
V
3,6
11.4
12.6
V
VLKO
VCC Program/Erase Lock
Voltage
1.5
V
VLKO2
VCCQ Program/Erase
Lock Voltage
1.2
V
NOTES:
1. All currents are in RMS unless otherwise noted. Typical values at nominal VCC, TA = +25°C.
2. ICCES and ICCWS are specified with device de-selected. If device is read while in erase suspend, current draw is ICCR. If the
device is read while in program suspend, current draw is ICCR.
3. Erase and Program are inhibited when VPP < VPPLK and not guaranteed outside the valid VPP ranges of VPPH1 and VPPH2.
4. Sampled, not 100% tested.
5. Automatic Power Savings (APS) reduces ICCR to approximately standby levels in static operation (CMOS inputs).
6. Applying VPP = 11.4V–12.6V during program/erase can only be done for a maximum of 1000 cycles on the main blocks
and 2500 cycles on the parameter blocks. VPP may be connected to 12V for a total of 80 hours maximum. See Section 3.4
for details.
7. Includes the sum of VCC and VCCQ current.
Table 11. Capacitance (TA = 25°C, f = 1 MHz)
Sym
Parameter
Notes
Typ
Max
Units
Conditions
CIN
Input Capacitance
1
6
8
pF
VIN = 0V
COUT
Output Capacitance
1
10
12
pF
VOUT = 0V
NOTE:
1. Sampled, not 100% tested.
32
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
VCCQ
VCCQ
INPUT
TEST POINTS
2
VCCQ
2
OUTPUT
0.0
0605-011
NOTE:
AC test inputs are driven at VCCQ for a logic “1” and 0.0V for a logic “0.” Input timing begins, and output timing ends, at VCCQ/2.
Input rise and fall times (10%–90%) <10 ns. Worst case speed conditions are when VCCQ=2.7V.
Figure 10. 2.7V–3.6V Input Range and Measurement Points
Test Configuration Component Values
for Worst Case Speed Conditions
VCCQ
Test Configuration
R
2.7V Standard Test
1
Device
under
Test
CL (pF) R1 (Ω) R2 (Ω)
50
25K
25K
Out
CL
R
2
0605-012
NOTE:
See table for component values.
Figure 11. Test Configuration
PRELIMINARY
33
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
6.0
OPERATING CONDITIONS (VCCQ = 1.8V–2.2V)
Table 12. Temperature and VCC Operating Conditions
Symbol
Parameter
Notes
Min
Max
Units
–40
+85
°C
TA
Operating Temperature
VCC1
2.7V–2.85V VCC Supply Voltage
1
2.7
2.85
Volts
VCC2
2.7V–3.3V VCC Supply Voltage
1
2.7
3.3
Volts
VCCQ
1.8V–2.2V I/O Supply Voltage
1,4
1.8
2.2
Volts
VPP1
Program and Erase Voltage
1
2.7
2.85
Volts
VPP2
1
2.7
3.3
Volts
VPP3
1,2
11.4
12.6
Volts
3
10,000
Cycling
Block Erase Cycling
Cycles
NOTES:
1. See DC Characteristics tables for voltage range-specific specifications.
2. Applying VPP = 11.4V–12.6V during program/erase can only be done for a maximum of 1000 cycles on the main blocks
and 2500 cycles on the parameter. VPP may be connected to 12V for a total of 80 hours maximum. See Section 3.4 for
details.
3. For operating temperatures of –25°C– +85°C the device is projected to have a minimum block erase cycling of 10,000 to
30,000 cycles.
4. The voltage swing on the inputs, VIN is required to match VCCQ.
6.1
DC Characteristics: VCCQ = 1.8V–2.2V
These tables are valid for the following power supply combinations only:
1. VCC1 and VCCQ and (VPP1 or VPP3)
2. VCC2 and VCCQ and (VPP2 or VPP3)
Wherever the input voltage VIN is mentioned, it is required that V IN matches the chosen V CCQ.
34
PRELIMINARY
E
Sym
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 13. DC Characteristics: VCCQ = 1.8V–2.2V
Parameter
Notes
VCC1:
2.7V–2.85V
VCC2:
2.7V–3.3V
Typ
Unit
Test Conditions
Max
ILI
Input Load Current
1
± 1.0
µA
VCC = VCCMax
VCCQ = VCCQMax
VIN = VCCQ or GND
ILO
Output Leakage Current
1
± 10
µA
VCC = VCC Max
VCCQ = VCCQMax
VIN = VCCQ or GND
ICCS
VCC Standby Current
50
µA
CMOS INPUTS
VCC = VCC1 Max (2.7V–2.85V)
VCCQ = VCCQMax
1,7
20
CE# = RP# = VCCQ
150
250
µA
CMOS INPUTS
VCC = VCC2 Max (2.7V–3.3V)
VCCQ = VCCQMax
CMOS INPUTS
VCC = VCCMax (VCC1 or VCC2)
VCCQ = VCCQMax
VIN = VCCQ or GND
RP# = GND ± 0.2V
CMOS INPUTS
VCC = VCC1Max (2.7V–2.85V)
VCCQ = VCCQMax
OE# = VIH , CE# = VIL
f = 5 MHz, I OUT = 0 mA
CE# = RP# = VCCQ
ICCD
VCC Deep Power-Down
Current
ICCR
VCC Read Current
1,7
1
10
µA
1,5,7
8
18
mA
Inputs = VIL or VIH
12
23
mA
CMOS INPUTS
VCC = VCC2Max (2.7V–3.3V)
VCCQ = VCCQMax
OE# = VIH , CE# = VIL
f = 5 MHz, I OUT = 0 mA
Inputs = GND ± 0.2V or VCCQ
PRELIMINARY
35
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 13. DC Characteristics: VCCQ = 1.8V–2.2V (Continued)
Sym
ICCW
ICCE
Parameter
VCC Program Current
VCC Erase Current
Notes
1,4,7
1,4,7
VCC1:
2.7V–2.85V
VCC2:
2.7V–3.3V
Unit
E
Test Conditions
Typ
Max
8
20
mA
VPP = VPPH1 or VPPH2
Program in Progress
8
20
mA
VPP = VPPH3 (12V)
Program in Progress
8
20
mA
VPP = VPPH1 or VPPH2
Erase in Progress
8
20
mA
VPP = VPPH3 (12V)
Erase in Progress
ICCES
VCC Erase Suspend
Current
1,2,4,7
20
50
µA
CE# = VIH
Erase Suspend in Progress
ICCWS
VCC Program Suspend
Current
1,2,4,7
20
50
µA
CE# = VIH
Program Suspend in Progress
IPPD
VPP Deep Power-Down
Current
1
0.2
5
µA
RP# = GND ± 0.2V
IPPR
VPP Read and Standby
Current
1
2
±50
µA
VPP ≤ VCC
IPPW
VPP Program Current
1,4
15
40
mA
VPP = VPPH1 or VPPH2
Program in Progress
10
25
mA
VPP = VPPH3 (12V)
Program in Progress
13
25
mA
VPP = VPPH1 or VPPH2
IPPE
VPP Erase Current
1,4
Erase in Progress
8
25
mA
VPP = VPPH3 (12V)
Erase in Progress
IPPES
VPP Erase Suspend
Current
1
50
200
µA
VPP = VPPH1 , VPPH2 , or VPPH3
Erase Suspend in Progress
IPPWS
VPP Program Suspend
Current
1
50
200
µA
VPP = VPPH1 , VPPH2 , or VPPH3
Program Suspend in Progress
36
PRELIMINARY
E
Sym
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 13. DC Characteristics: VCCQ = 1.8V–2.2V (Continued)
Parameter
Notes
VCC1:
2.7V–2.85V
VCC2:
2.7V–3.3V
Typ
Max
Input Low Voltage
–0.2
0.2
VIH
Input High Voltage
VCCQ –
0.2V
VOL
Output Low Voltage
–0.10
VIL
Unit
Test Conditions
V
V
0.10
V
VCC = VCCMin
VCCQ = VCCQMin
IOL = 100 µA
VOH
Output High Voltage
VPPLK
VPP Lock-Out Voltage
VPPH1
VPP during Prog./Erase
Operations
VPPH2
VPPH3
VLKO1
VLKO2
VCCQ –
0.1V
V
VCC = VCCMin
VCCQ = VCCQMin
IOH = –100 µA
3
1.5
V
Complete Write Protection
3
2.7
2.85
V
3
2.7
3.3
V
3,6
11.4
12.6
V
VCC Program/Erase Lock
Voltage
VCCQ Program/Erase
Lock Voltage
1.5
V
1.2
V
NOTES:
1. All currents are in RMS unless otherwise noted. Typical values at nominal VCC, TA = +25°C.
2. ICCES and ICCWS are specified with device de-selected. If device is read while in erase suspend, current draw is ICCR. If the
device is read while in program suspend, current draw is ICCR.
3. Erases and Writes inhibited when VPP < VPPLK, and not guaranteed outside the valid VPP ranges of VPPH1,VPPH2. or VPPH3.
4. Sampled, not 100% tested.
5. Automatic Power Savings (APS) reduces ICCR to approximately standby levels in static operation (CMOS inputs).
6. Applying VPP = 11.4V–12.6V during program/erase can only be done for a maximum of 1000 cycles on the main blocks
and 2500 cycles on the parameter blocks. VPP may be connected to 12V for a total of 80 hours maximum. See Section 3.4
for details.
7 Includes the sum of VCC and VCCQ current
Table 14. Capacitance (TA = 25°C, f = 1 MHz)
Sym
Parameter
Notes
Typ
Max
Units
Conditions
CIN
Input Capacitance
1
6
8
pF
VIN = 0V
COUT
Output Capacitance
1
10
12
pF
VOUT = 0V
NOTE:
1. Sampled, not 100% tested.
PRELIMINARY
37
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
VCCQ
VCCQ
INPUT
TEST POINTS
2
VCCQ
2
OUTPUT
0.0
0605-011
NOTE:
AC test inputs are driven at VCCQ for a logic “1” and 0.0V for a logic “0.” Input timing begins, and output timing ends, at VCCQ/2.
Input rise and fall times (10%–90%) <10 ns. For worst case speed conditions VCCQ=1.8V.
Figure 12. 1.8V—2.2V Input Range and Measurement Points
Test Configuration Component Values
for Worst Case Speed Conditions
VCCQ
Test Configuration
R
1.8V Standard Test
1
Device
under
Test
Out
CL (pF) R1 (Ω) R2 (Ω)
50
16.7K 16.7K
NOTE:
CL includes jig capacitance.
CL
R
2
0605-012
NOTE:
See table for component values.
Figure 13. Test Configuration
38
PRELIMINARY
E
7.0
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
AC CHARACTERISTICS
AC Characteristics are applicable to both VCCQ ranges.
Table 15. AC Characteristics: Read Operations (Extended Temperature)
#
Symbol
Parameter
Load
CL = 50 pF
VCC
2.7V–3.6V4
Prod
Notes
120 ns
Min
Max
120
Units
150 ns
Min
Max
R1
tAVAV
Read Cycle Time
R2
tAVQV
Address to Output Delay
R3
tELQV
CE# to Output Delay
2
R4
tGLQV
OE# to Output Delay
2
R5
tPHQV
RP# to Output Delay
R6
tELQX
CE# to Output in Low Z
3
0
0
ns
R7
tGLQX
OE# to Output in Low Z
3
0
0
ns
R8
tEHQZ
CE# to Output in High Z
3
40
40
ns
R9
tGHQZ
OE# to Output in High Z
3
40
40
ns
R10
tOH
Output Hold from Address, CE#,
or OE# Change, Whichever
Occurs First
3
0
150
ns
120
150
ns
120
150
ns
65
65
ns
600
600
ns
0
ns
NOTES:
1. See AC Input/Output Reference Waveform for timing measurements.
2. OE# may be delayed up to tELQV–tGLQV after the falling edge of CE# without impact on tELQV.
3. Sampled, but not 100% tested.
4. See Test Configuration (Figures 11 and 13), 2.7V–3.6V and 1.8V–2.2V Standard Test component values.
PRELIMINARY
39
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
CE# (E)
Data
Valid
Device and
Address Selection
VIH
ADDRESSES (A)
VIL
Standby
Address Stable
R1
VIH
VIL
OE# (G)
R8
VIH
VIL
R9
VIH
WE# (W)
VIL
VOH
DATA (D/Q)
VOL
RP#(P)
R7
High Z
R10
R3
R6
Valid Output
High Z
R2
VIH
VIL
R4
R5
0605-015
Figure 14. AC Waveform: Read Operations
40
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 16. AC Characteristics: Write Operations (Extended Temperature)1
Load
#
Symbol
Parameter
50 pF
VCC
2.7V–3.6V5
2.7V-3.6V5
Prod
120 ns
150 ns
Notes
Min
Max
Min
Units
Max
W1
tPHWL
tPHEL
RP# High Recovery to
WE# (CE#) Going Low
600
600
ns
W2
tELWL
tWLEL
CE# (WE#) Setup to
WE# (CE#) Going Low
0
0
ns
W3
tWLWH
tELEH
WE# (CE#) Pulse Width
90
90
ns
W4
tDVWH
tDVEH
Data Setup to WE#
(CE#) Going High
3
70
70
ns
W5
tAVWH
tAVEH
Address Setup to WE#
(CE#) Going High
2
90
90
ns
W6
tWHEH
tEHWH
CE# (WE#) Hold Time
from WE# (CE#) High
0
0
ns
W7
tWHDX
tEHDX
Data Hold Time from
WE# (CE#) High
3
0
0
ns
W8
tWHAX
tEHAX
Address Hold Time from
WE# (CE#) High
2
0
0
ns
W9
tWHWL
tEHEL
WE# (CE#) Pulse Width
High
30
30
ns
W10
tVPWH
tVPEH
VPP Setup to WE# (CE#)
Going High
4
200
200
ns
W11
tQVVL
VPP Hold from Valid SRD
4
0
0
ns
tLOCK
Block Unlock / Lock
Delay
4, 6
200
200
ns
NOTES:
1. Read timing characteristics during program suspend and erase suspend are the same as during read-only operations.
Refer to AC Characteristics during read mode.
2. Refer to command definition table for valid AIN (Table6).
3. Refer to command definition table for valid DIN (Table 6).
4. Sampled, but not 100% tested.
5. See Test Configuration (Figure 11 and 13), 2.7V–3.6V and 1.8V–2.2V Standard Test component values.
6. Time tLOCK is required for successful locking and unlocking of all lockable blocks.
PRELIMINARY
41
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
VIH
A
B
C
AIN
ADDRESSES [A]
VIL
VIH
D
E
F
AIN
W8
W5
(Note 1)
CE#(WE#) [E(W)]
VIL
W6
VIH W2
OE# [G]
VIL
W9
(Note 1)
VIH
WE#(CE#) [W(E)]
VIL
W3
W4
VIH
DATA [D/Q]
High Z
VIL
RP# [P]
W7
DIN
DIN
W1
Valid
SRD
DIN
VIH
VIL
VIH
WP#
V
[V]
PP
VIL
W10
W11
VPPH 2
VPPH1
VPPLK
VIL
0605-016
NOTES:
1. CE# must be toggled low when reading Status Register Data. WE# must be inactive (high) when reading Status Register
Data.
A.
B.
C.
D.
E.
F.
VCC Power-Up and Standby.
Write Program or Erase Setup Command.
Write Valid Address and Data (for Program) or Erase Confirm Command.
Automated Program or Erase Delay.
Read Status Register Data (SRD): reflects completed program/erase operation.
Write Read Array Command.
Figure 15. AC Waveform: Program and Erase Operations
42
PRELIMINARY
E
7.1
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Reset Operations
RP# (P)
VIH
VIL
t PLPH
(A) Reset during Read Mode
t PHQV
t PHWL
t PHEL
Abort
Complete
t PLRH
RP# (P)
VIH
t PHQV
t PHWL
t PHEL
VIL
t PLPH
(B) Reset during Program or Block Erase, t PLPH < t PLRH
Abort Deep
Complete PowerDown
RP# (P)
VIH
V IL
t PLRH
t PHQV
t PHWL
t PHEL
t PLPH
(C) Reset Program or Block Erase, t PLPH > t PLRH
0605-17
Figure 16. AC Waveform: Deep Power-Down/Reset Operation
Reset Specifications
VCC = 2.7–3.6V
Notes
Min
tPLPH
Symbol
RP# Low to Reset during Read
(If RP# is tied to VCC, this specification is not
applicable)
Parameter
1,3
100
tPLRH
RP# Low to Reset during Block Erase or Program
2,3
Max
Unit
ns
22
µs
NOTES:
1. If tPLPH is < 100 ns the device may still RESET but this is not guaranteed.
2. If RP# is asserted while a block erase or byte program operation is not executing, the reset will complete within 100 ns.
3. Sampled but not 100% tested.
PRELIMINARY
43
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
Table 17. Erase and Program Timings
VPP = 2.7V
Sym
Parameter
VPP = 12V
Notes
Typ1
Max3
Typ1
Max3
Unit
tBWPB
Block Program Time
(Parameter)
2
.16
.48
.08
.24
sec
tBWMB
Block Program Time (Main)
2
1.23
3.69
.58
1.74
sec
tWHQV1
tEHQV1
Program Time
2
17
165
8
185
µs
tWHQV2
tEHQV2
Block Erase Time (Parameter)
2
1
5.0
0.8
4.8
sec
tWHQV3
tEHQV3
Block Erase Time (Main)
2
1.8
8.0
1.1
7.0
sec
tWHRH1
tEHRH1
Program Suspend Latency
3
5
10
5
10
µs
tWHRH2
tEHRH2
Erase Suspend Latency
3
5
20
6
12
µs
NOTES:
1. Typical values measured at TA = +25°C and nominal voltages.
2. Excludes external system-level overhead.
3. Sampled but not 100% tested.
44
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
APPENDIX A
ORDERING INFORMATION
T E2 8 F 1 6 0 B3 T 1 2 0
Package
TE = 40-Lead TSOP
GT = 48-Ball µBGA* CSP
Access Speed (ns)
(120, 150)
Product line designator
for all Intel Flash products
T = Top Blocking
B = Bottom Blocking
Device Density
016 = x8 (16-Mbit)
008 = x8 (8-Mbit)
Product Family
B3 = Smart 3 Advanced Boot Block
VCC = 2.7V - 3.6V
VPP = 2.7V - 3.6V or 11.4V - 12.6V
VALID COMBINATIONS
Extended
Extended
PRELIMINARY
16M
8M
40-Lead TSOP
TE28F016B3T120
TE28F016B3B120
48-Ball µBGA* CSP
GT28F016B3T120
GT28F016B3B120
TE28F016B3T150
TE28F016B3B150
GT28F016B3T150
GT28F016B3B150
TE28F008B3T120
TE28F008B3B120
GT28F008B3T120
GT28F008B3B120
TE28F008B3T150
TE28F008B3B150
GT28F008B3T150
GT28F008B3B150
45
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
APPENDIX B
WRITE STATE MACHINE CURRENT/NEXT STATES
Command Input (and Next State)
Current
State
SR.7
Data
When
Read
Read
Array
(FFH)
Program
Setup
(40/10H)
Erase
Setup
(20H)
Read Array
“1”
Array
Read
Array
Program
Setup
Erase
Setup
Program
Setup
“1”
Status
Pgm.
Program
(Not Comp.)
“0”
Status
Program
(Complete)
“1”
Status
Read
Array
Program
Suspend to
Status
“1”
Status
Prog.
Susp. to
Array
Program Suspend
Program
Suspend to
Array
“1”
Array
Prog.
Susp. to
Array
Program Suspend
to Array
Erase Setup
“1”
Status
Erase
Cmd. Error
“1”
Status
Erase
(Not Comp)
“0”
Status
Erase
(Complete)
“1”
Status
Read
Array
Program
Setup
Erase
Setup
Erase
Suspend to
Status
“1”
Status
Erase
Susp. to
Array
Program
Setup
Erase
Susp. to
Array
Erase
Erase
Susp. to
Array
Erase
Erase
Susp. to
Status
Erase Suspend
to Array
Erase. Susp.
to Array
“1”
Array
Erase
Susp. to
Array
Program
Setup
Erase
Susp. to
Array
Erase
Erase
Susp. to
Array
Erase
Erase
Susp. to
Status
Erase Suspend
to Array
Read Status
“1”
Status
Read
Array
Program
Setup
Erase
Setup
Read Array
Read
Status
Read
Array
Read
Identifier
Read
Identifier
“1”
ID
Read
Array
Program
Setup
Erase
Setup
Read Array
Read
Status
Read
Read
Identifier
1.
46
1
Erase
Confirm
(D0H)
Program /
Erase
Resume
(D0)
Read Array
Read
Status
(70H)
Clear
Status
(50H)
Read ID
(90H)
Read
Status
Read
Array
Read
Identifier
Program (Command input = Data to be programmed)
Program
Program
Setup
Pgm Susp.
to Status
Erase
Setup
Program
Setup
Program
Read Array
Read
Status
Read
Array
Read
Identifier
Program
Program
Susp. to
Array
Program
Prog.
Susp. to
Status
Program Suspend to
Array
Program
Program
Susp. to
Array
Program
Prog.
Susp. to
Status
Prog.
Susp. to
Array
Erase
Erase
Cmd. Err.
Erase
to Array
Erase Command Error
Read
Array
Program /
Erase
Susp.
(B0H)
Erase
Setup
Read Array
Erase
Erase Command Error
Read
Status
Ers. Susp.
to Status
Prog.
Susp. to
Array
Read
Array
Read
Identifier
Erase
Read Array
Read
Status
Read
Array
Array
Read
Identifier
You cannot program “1”s to the flash. Writing FFH following the Program Setup will initiate the internal program algorithm
of the WSM. Although the algorithm will execute, array data is not changed. The WSM returns to read status mode without
reporting any error. Assuming VPP > VPPLK writing a second FFH while in read status mode will return the flash to read
array mode.
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
APPENDIX C
ACCESS TIME VS. CAPACITIVE LOAD
(tAVQV vs. CL)
Access Time vs. Load Capacitance
Derating Curve
124
123
Access Time(ns)
122
121
120
Smart 3 Advanced Boot
Block
119
118
117
116
115
30
50
70
100
Load Capacitance(pF)
NOTE:
VCCQ = 2.7V
This chart shows a derating curve for device access time with respect to capacitive load. The value in the
DC characteristics section of the specification corresponds to C L = 50 pF.
NOTE:
1. Sampled, but not 100% tested
PRELIMINARY
47
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
APPENDIX D
ARCHITECTURE BLOCK DIAGRAM
E
DQ0-DQ7
VCCQ
Power
Reduction
Control
Input Buffer
Identifier
Register
Status
Register
Data
Register
Output
Multiplexer
Output Buffer
I/O Logic
CE#
WE#
OE#
RP#
Command
User
Interface
Data
Comparator
WP#
A0-A20
Y-Decoder
Y-Gating/Sensing
Write State
Machine
Address
Counter
48
64-Kbyte
Main Block
X-Decoder
8-Kbyte
Parameter Block
64-Kbyte
Main Block
Address
Latch
8-Kbyte
Parameter Block
Input Buffer
Program/Erase
Voltage Switch
VPP
VCC
GND
PRELIMINARY
E
SMART 3 ADVANCED BOOT BLOCK–BYTE-WIDE
APPENDIX E
ADDITIONAL INFORMATION(1,2)
Order Number
Document/Tool
210830
1997 Flash Memory Databook
290580
Smart 3 Advanced Boot Block Word-Wide 4-Mbit (256K x 16), 8-Mbit (512K
x16), 16-Mbit (1024K x16) Flash Memory Family Datasheet
292172
AP-617 Additional Flash Data Protection Using VPP, RP# and WP#
NOTE:
1. Please call the Intel Literature Center at (800) 548-4725 to request Intel documentation. International customers should
contact their local Intel or distribution sales office.
2. Visit Intel’s World Wide Web home page at http://www.Intel.com for technical documentation and tools.
PRELIMINARY
49