TI TL16C451_08

TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
D
D
D
Integrates Most Communications Card
Functions From the IBM PC/AT  or
Compatibles With Single- or Dual-Channel
Serial Ports
TL16C451 Consists of One TL16C450 Plus
Centronix Printer Interface
TL16C452 Consists of Two TL16C450s Plus
a Centronix-Type Printer Interface
D
D
Fully Programmable Serial Interface
Characteristics:
– 5-, 6-, 7-, or 8-Bit Characters
– Even-, Odd-, or No-Parity Bit Generation
and Detection
– 1-, 1 1/2-, or 2 Stop-Bit Generation
– Programmable Baud Rate
(dc to 256 kbit/s)
Fully Double Buffered for Reliable
Asynchronous Operation
description
The TL16C451 and TL16C452 provide single- and dual-channel (respectively) serial interfaces along with a
single Centronix-type parallel-port interface. The serial interfaces provide a serial-to-parallel conversion for data
received from a peripheral device or modem and a parallel-to-serial conversion for data transmitted by a CPU.
The parallel interface provides a bidirectional parallel data port that fully conforms to the requirements for a
Centronix-type printer interface. A CPU can read the status of the asynchronous communications element
(ACE) interfaces at any point in the operation. The status includes the state of the modem signals (CTS, DSR,
RLSD, and RI) and any changes to these signals that have occurred since the last time they were read, the state
of the transmitter and receiver including errors detected on received data, and printer status. The TL16C451
and TL16C452 provide control for modem signals (RTS and DTR), interrupt enables, baud rate programming,
and parallel-port control signals.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
IBM PC/AT is a trademark of International Business Machines Corporation.
Copyright  1999, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
9 8
NC
NC
NC
GND
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
GND
VCC
RTS0
DTR0
SOUT0
7 6 5
10
11
GND
LPTOE
ACK
PE
BUSY
SLCT
VCC
ERROR
GND
GND
GND
GND
GND
GND
GND
CLK
VCC
TL16C451 . . . FN PACKAGE
(TOP VIEW)
4 3 2 1 68 67 66 65 64 63 62 61
60 NC
59 INT2
58 SLIN
57 INIT
12
13
56 AFD
55 STB
14
15
54 GND
53 PD0
16
17
52 PD1
51 PD2
18
19
50 PD3
49 PD4
20
21
23
48 PD5
47 PD6
24
46 PD7
25
45 INT0
44 BDO
22
26
NC – No internal connection
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SIN0
GND
GND
GND
CTS0
RLSD0
RI0
DSR0
CS0
A2
A1
A0
IOW
IOR
CS2
RESET
VCC
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
GND
RLSD1
GND
RI1
DSR1
CLK
CS1
GND
LPTOE
ACK
PE
BUSY
SLCT
VCC
ERROR
SIN1
GND
TL16C452 . . . FN PACKAGE
(TOP VIEW)
9 8 7 6 5 4 3 2 1 68 67 66 65 64 63 62 61
60 INT1
59 INT2
10
11
58 SLIN
57 INIT
12
13
56 AFD
55 STB
14
15
54 GND
53 PD0
16
17
52 PD1
51 PD2
18
19
50 PD3
49 PD4
20
21
23
48 PD5
47 PD6
24
46 PD7
25
45 INT0
44 BDO
22
26
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SIN0
GND
GND
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
GND
CTS0
RLSD0
RI0
DSR0
CS0
A2
A1
A0
IOW
IOR
CS2
RESET
VCC
SOUT1
DTR1
RTS1
CTS1
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
GND
VCC
RTS0
DTR0
SOUT0
3
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
TL16C451 functional block diagram
TL16C451
28
31
29
30
41
32
14 – 21
CTS0
DSR0
RLSD0
RI0
SIN0
CS0
8
DB0 – DB7
35 – 33
36
37
39
4
3
A0 – A2
IOW
IOR
RESET
CLK
ACE
1
24
25
26
45
RTS0
DTR0
SOUT0
INT0
8
Select
and
Control
Logic
44
BDO
8
63
65
66
67
68
1
38
ERROR
SLCT
BUSY
PE
ACK
LPTOE
CS2
Parallel
Port
Parallel
Port
53 – 46
57
56
55
58
59
8
PD0 – PD7
INIT
AFD
STB
SLIN
INT2
TL16C452 functional block diagram
TL16C452
28
31
29
30
41
32
14 – 21
CTS0
DSR0
RLSD0
RI0
SIN0
CS0
8
DB0 – DB7
8
CTS1
DSR1
RLSD1
RI1
SIN1
CS1
A0 – A2
IOW
IOR
RESET
CLK
ERROR
SLCT
BUSY
PE
ACK
LPTOE
CS2
4
3
35 – 33
36
37
39
4
Select
and
Control
Logic
13
5
8
6
62
3
ACE
1
24
25
26
45
RTS0
DTR0
SOUT0
INT0
ACE
2
12
11
10
60
RTS1
DTR1
SOUT1
INT1
44
BDO
8
63
65
66
67
68
1
38
POST OFFICE BOX 655303
Parallel
Port
53 – 46
57
56
55
58
59
• DALLAS, TEXAS 75265
8
PD0 – PD7
INIT
AFD
STB
SLIN
INT2
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
Terminal Functions
TERMINAL
NAME†
NO.
I/O
DESCRIPTION
A0
A1
A2
35
34
33
I
Register select. A0, A1, and A2 are used during read and write operations to select the register to read
from or write to. Refer to Table 1 for register addresses, also refer to the chip select signals (CS0, CS1,
CS2).
ACK
68
I
Printer acknowledge. ACK goes low to indicate that a successful data transfer has taken place. It
generates a printer port interrupt during its positive transition.
AFD
56
I/O
Printer autofeed. AFD is an open-drain line that provides the printer with a low signal when
continuous-form paper is to be autofed to the printer. An internal pullup is provided.
BDO
44
O
Bus buffer output. BDO is active (high) when the CPU is reading data. When active, this output can
disable an external transceiver.
BUSY
66
I
Printer busy. BUSY is an input line from the printer that goes high when the printer is not ready to accept
data.
CLK
4
I/O
CS0
CS1 [VCC]
CS2
32
3
38
I
Chip selects. Each chip select enables read and write operations to its respective channel. CS0 and
CS1 select serial channels 0 and 1, respectively, and CS2 selects the parallel port.
CTS0
CTS1 [GND]
28
13
I
Clear to send. CTSx is an active-low modem status signal. Its state can be checked by reading bit 4
(CTS) of the modem status register. Bit 0 (DCTS) of the modem status register indicates that this signal
has changed states since the last read from the modem status register. If the modem status interrupt
is enabled when CTSx changes state, an interrupt is generated.
14 – 21
I/O
Data bus. Eight 3-state data lines provide a bidirectional path for data, control, and status information
between the TL16C451/TL16C452 and the CPU. DB0 is the least significant bit (LSB).
DSR0
DSR1 [GND]
31
5
I
Data set ready. DSRx is an active-low modem status signal. Its state can be checked by reading
bit 5 (DSR) of the modem status register. Bit 1 (DDSR) of the modem status register indicates that this
signal has changed states since the last read from the modem status register. If the modem status
interrupt is enabled when the DSRx changes state, an interrupt is generated.
DTR0
DTR1 [NC]
25
11
O
Data terminal ready. DTRx, when active (low), informs a modem or data set that the ACE is ready to
establish communication. DTRx is placed in the active state by setting the DTR bit of the modem control
register. DTRx is placed in the inactive state either as a result of a reset or during loop mode operation
or clearing bit 0 (DTR) of the modem control register.
ERROR
63
I
Printer error. ERROR is an input line from the printer. The printer reports an error by holding this line
low during the error condition.
INIT
57
I/O
Printer initialize. INIT is an open-drain line that provides the printer with a signal that allows the printer
initialization routine to be started. An internal pullup is provided.
INT0
INT1 [NC]
45
60
O
Interrupt. INTx is an active-high 3-state output that is enabled by bit 3 of the MCR. When active, INTx
informs the CPU that the ACE has an interrupt to be serviced. Four conditions that cause an interrupt
to be issued are: a receiver error, received data is available, the transmitter holding register is empty,
and an enabled modem status interrupt. The INTx output is reset (low) either when the interrupt is
serviced or as a result of a reset.
INT2
59
O
Printer port interrupt. INT2 is an active-high 3-state output generated by the positive transition of ACK.
It is enabled by bit 4 of the write control register.
IOR
37
I
Data read strobe. When IOR input is active (low) while the ACE is selected, the CPU is allowed to read
status information or data from a selected ACE register.
IOW
36
I
Data write strobe. When IOW input is active (low) while the ACE is selected, the CPU is allowed to write
control words or data into a selected ACE register.
1
I
Parallel data output enable. When low, LPTOE enables the write data register to the PD0 – PD7 lines.
A high puts the PD0 – PD7 lines in the high-impedance state allowing them to be used as inputs. LPTOE
is usually tied low for printer operation.
DB0 – DB7
LPTOE
External clock. CLK connects the ACE to the main timing reference.
† Names shown in brackets are for the TL16C451.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
Terminal Functions (continued)
TERMINAL
NAME†
NO.
I/O
DESCRIPTION
53 – 46
I/O
Parallel data bits (0 – 7). These eight lines provide a byte-wide input or output port to the system. The
eight lines are held in a high-impedance state when LPTOE is high.
PE
67
I
Printer paper empty. This is an input line from the printer that goes high when the printer runs out of
paper.
RESET
39
I
Reset. When active (low), RESET clears most ACE registers and sets the state of various output
signals. Refer to Table 2.
RI0
RI1 [GND]
30
6
I
Ring indicator. RIx is an active-low modem status signal. Its state can be checked by reading bit 6 (RI)
of the modem status register. Bit 2 (TERI) of the modem status register indicates that the RIx input has
transitioned from a low to a high state since the last read from the modem status register. If the modem
status interrupt is enabled when this transition occurs, an interrupt is generated.
RLSD0
RLSD1 [GND]
29
8
I
Receive line signal detect. RLSDx is an active-low modem status signal. Its state can be checked by
reading bit 7 of the modem status register. Bit 3 (DRLSD) of the modem status register indicates that
this signal has changed states since the last read from the modem status register. If the modem status
interrupt is enabled when RLSDx changes state, an interrupt is generated. This bit is low when a data
carrier is detected.
RTS0
RTS1 [NC]
24
12
O
Request to send. When active (low), RTSx informs the modem or data set that the ACE is ready to
transmit data. RTSx is set to its active state by setting the RTS modem control register bit and is set
to its inactive (high) state either as a result of a reset or during loop mode operations or by clearing bit
1 (RTS) of the modem control register.
SIN0
SIN1 [GND]
41
62
I
Serial input. SINx is a serial data input from a connected communications device.
SLCT
65
I
Printer selected. SLCT is an input line from the printer that goes high when the printer has been selected.
SLIN
58
I/O
Printer select. SLIN is an open-drain line that selects the printer when it is active (low). An internal pullup
is provided on this line.
SOUT0
SOUT1 [NC]
26
10
I
Serial output. SOUTx is a composite serial data output to a connected communication device. SOUTx
is set during a reset.
STB
55
I/O
Printer strobe. STB is an open-drain line that provides communication synchronization between the
TL16C451/TL16C452 and the printer. When it is active (low), it provides the printer with a signal to latch
the data currently on the parallel port. An internal pullup is provided on this line.
VCC
23,40,
64
GND
2,7,9
22,27,42,
43,54,61
PD0 – PD7
5-V supply voltage
Supply common
† Names shown in brackets are for the TL16C451.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC (see Note 1 ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V
Input voltage range at any input, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V
Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 7 V
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100 mW
Operating free-air temperature range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 °C to 70 °C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65 °C to 150 °C
Case temperature for 10 seconds, TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260 °C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values are with respect to GND.
recommended operating conditions
Supply voltage, VCC
MIN
NOM
4.75
5
UNIT
5.25
V
V
– 0.5
VCC
0.8
0
70
°C
High-level Input voltage, VIH
2
Low-level Input voltage, VIL
MAX
Operating free-air temperature, TA
V
electrical characteristics over recommended ranges of supply voltage and operating free-air
temperature (unless otherwise noted)
PARAMETER
VOH
TEST CONDITIONS
MIN
IOH = – 0.4 mA on DB0 – DB7
IOH = – 2 mA to 4 mA on PD0 – PD7
High level output voltage
High-level
TYP†
MAX
24
2.4
IOH = – 0.2 mA on INIT,
AFD, STB, and SLIN
IOH = – 0.2 mA on all other outputs
UNIT
V
IOL = 4 mA on DB0 – DB7
IOL = 12 mA on PD0 – PD7
VOL
Low-level output voltage
IOL = 10 mA on INIT,
AFD, STB, and SLIN (see Note 2)
0.4
V
± 10
µA
± 20
µA
10
mA
IOL = 2 mA on all other outputs
IIkg
Ik
Input leakage current
VCC = 5.25 V,,
VI = 0 to 5.25 V,
VSS = 0,,
All other terminals floating
Ioz
High-impedance output current
VCC = 5.25 V,
VSS = 0,
VO = 0 to 5.25 V,
Chip selected and in write mode, or chip deselected
ICC
Supply current
VCC = 5.25 V,
VSS = 0,
SIN,
S
DSR,
S RLSD,
S CTS,
C S and RI at 2 V,
All other in
inputs
uts at 0.8
0 8 V,
V
XTAL1 at 4 MHz
MHz,
No load on outputs,
Baud rate = 50 kbit/s
† All typical values are at VCC = 5 V, TA = 25 °C.
NOTE 2: INIT, AFD, STB, and SLIN are open-collector output terminals that each have an internal pullup to VCC. This generates a maximum of
2 mA of internal IOL per terminal. In addition to this internal current, each terminal sinks at least 10 mA while maintaining the VOL
specification of 0.4 V maximum.
system timing requirements over recommended ranges of supply voltage and operating free-air
temperature
PARAMETER
tcR
FIGURE
Cycle time, read (tw7 + td8 + td9)
MIN
175
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MAX
UNIT
ns
7
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
tcW
tw1
Cycle time, write (tw6 + td5 + td6)
175
ns
Pulse duration, clock↑
tw2
tw5
Pulse duration, clock↓
1
50
ns
1
50
ns
tw6
twRST
Pulse duration, write strobe (IOW)↑
2
80
ns
Pulse duration, read strobe (IOR)↓
3
80
ns
1000
ns
tsu1
tsu2
Setup time, address (A0 – A2) valid before IOW↓
Setup time, chip select (CSx) valid before IOW↓
2, 3
15
ns
2, 3
15
tsu3
th1
ns
Setup time, data (D0 – D7) valid before IOW↑
2
15
ns
th2
th3
Hold time, address (A0 – A2) valid after IOW↑
2, 3
20
ns
Hold time, chip select (CSx) valid after IOW↑
2, 3
20
ns
td3
td4
Hold time, data (D0 – D7) valid before IOW↑
2
15
ns
Delay time, write cycle (IOW)↑ to IOW↓
2
80
ns
Delay time, read cycle (IOR)↑ to IOR↓
3
80
ns
Pulse duration, reset
system switching characteristics over recommended ranges of supply voltage and operating
free-air temperature
PARAMETER
FIGURE
TEST CONDITIONS
td5
td6
Delay time, data (D0 – D7) valid before read (IOR)↑
3
CL = 100 pF
Delay time, floating data (D0 – D7) valid after read (IOR)↑
3
CL = 100 pF
tdis(R)
Read to driver disable, IOR↓ to BD0↓
3
CL = 100 pF
MIN
0
MAX
UNIT
60
ns
60
ns
60
ns
receiver switching characteristics over recommended ranges of supply voltage and operating
free-air temperature
PARAMETER
td7
FIGURE
Delay time, RCLK↑ to sample clock↑
TEST CONDITIONS
MIN
4
td8
Delay time
time, stop (sample clock)↑ to set interrupt (INTRPT)↑
4
td9
Delay time, read RBR/LSR (IOR)↑ to reset interrupt (INTRPT)↓
4
MAX
100
1
CL = 100 pF
1
140
UNIT
ns
RCLK
cycles
ns
transmitter switching characteristics over recommended ranges of supply voltage and operating
free-air temperature
PARAMETER
FIGURE
TEST CONDITIONS
MIN
MAX
UNIT
td10
time initial write THR (IOW)↑ to transmit start (SOUT)↓
Delay time,
5
8
24
baudout
cycles
td11
Delay time
time, stop (SOUT) low to interrupt (INTRPT)↑
5
8
8
baudout
cycles
td12
Delay time, write THR (IOW)↓ to reset interrupt (INTRPT) low
5
td13
Delay time,
time initial write (IOW)↑ to THRE interrupt (INTRPT)↑
5
td14
Delay time, read IIR (IOR)↑ to reset THRE interrupt (INTRPT) low
5
CL = 100 pF
16
CL = 100 pF
140
ns
32
baudout
cycles
140
ns
modem control switching characteristics over recommended ranges of supply voltage and
operating free-air temperature
PARAMETER
td15
8
Delay time, write MCR (IOW)↑ to output (RTS, DTS)↓↑
POST OFFICE BOX 655303
FIGURE
TEST CONDITIONS
6
CL = 100 pF
• DALLAS, TEXAS 75265
MIN
MAX
UNIT
100
ns
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
td16
Delay time, modem input (CTS, DSR, RLSD)↑ to set interrupt
(INTRPT) high
6
CL = 100 pF
170
ns
td17
Delay time, read MSR (IOR)↑ to reset interrupt (INTRPT) low
6
CL = 100 pF
140
ns
parallel port switching characteristics over recommended ranges of supply voltage and operating
free-air temperature
PARAMETER
FIGURE
TEST CONDITIONS
Delay time, write parallel port control (SLIN, AFD, STB, INIT)↓↑ to
output (IOW) high
7
CL = 100 pF
60
ns
td19
td20
Delay time, write parallel port data (P0 – P7)↓↑ to output (IOW) high
7
CL = 100 pF
60
ns
Delay time, output enable to data, PD0 – PD7 valid after LPTOE↓
7
CL = 100 pF
60
ns
td21
Delay time, ACK↓↑ to INT2↓↑
7
CL = 100 pF
100
ns
td18
MIN
MAX
UNIT
PARAMETER MEASUREMENT INFORMATION
tw1
CLK
(9 MHz Max)
2V
0.8 V
tw2
N
CLK
BAUDOUT
(1/1)
(see Note A)
BAUDOUT
(1/2)
BAUDOUT
(1/3)
BAUDOUT
(1/N)
(N > 3)
2 Clock
Cycles
(N-2) Clock
Cycles
NOTE A: BAUDOUT is an internally generated signal used in the receiver and transmitter circuits to synchronize data.
Figure 1. Baud Generator Timing Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PARAMETER MEASUREMENT INFORMATION
90%
A0 – A2
Valid
10%
10%
90%
CS0, CS1, CS2
Valid
10%
10%
th2
t w5
th1
tsu2
tsu1
td3
IOW
90%
10%
10%
tsu3
th3
90%
D0 – D7
90%
Valid Data
Figure 2. Write Cycle Timing Waveforms
A0 – A2
90%
10%
Valid
90%
10%
CS0, CS1, CS2
Valid
10%
10%
th2
tsu2
tw6
th1
td4
tsu1
IOR
90%
10%
10%
tdis(R)
tdis(R)
BDO
10%
10%
td6
td5
90%
D0 – D7
90%
Valid Data
Figure 3. Read Cycle Timing Waveforms
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PARAMETER MEASUREMENT INFORMATION
RCLK
(internal signal only
same as BAUDOUT)
td7
8 CLKs
Sample Clock
(internal signal only)
Start
SIN
Data Bits 5 – 8
Parity
Stop
Sample
Clock
td8
INTRPT
(RDR/LSI)
90%
10%
td9
IOR
(RD RBR/LSR)
10%
Figure 4. Receiver Timing Waveforms
SOUT
10%
Start
Data Bits 5 – 8
Parity
td10
Start
td11
90%
INTRPT
(THRE)
Stop 50%
90%
50%
50%
10%
td13
td12
td12
IOW (WR THR)
10%
10%
10%
td14
IOR (RD IIR)
10%
Figure 5. Transmitter Timing Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PARAMETER MEASUREMENT INFORMATION
90%
IOW (WR MCR)
90%
td15
td15
90%
90%
RTS, DTR
CTS, DSR, RLSD
10%
td16
90%
INTRPT
(MODEM)
50%
50%
td17
IOR (RD MSR)
10%
td16
RI
50%
Figure 6. Modem Control Timing Waveforms
50%
IOW
50%
td18
90%
10%
SLIN, AFD,
STB, INIT
td19
90%
50%
PD0 – PD7
10%
td20
LPTOE
10%
90%
ACK
10%
td21
td21
90%
INT2
10%
Figure 7. Parallel Port Timing Waveforms
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
APPLICATION INFORMATION
Data Bus
ACE and
Printer
Port
Address Bus
Serial
Channel 0
Buffers
9-Pin
D
Conn
Parallel
Port
R/C Net
25-Pin
D
Conn
Control Bus
Option
Jumpers
Figure 8. Basic TL16C451 Test Configuration
Data Bus
Dual
ACE and
Printer
Port
Address Bus
Serial
Channel 0
Buffers
9-Pin
D
Conn
Serial
Channel 1
Buffers
9-Pin
D
Conn
Control Bus
Parallel
Port
R/C Net
Option
Jumpers
25-Pin
D
Conn
Figure 9. Basic TL16C452 Test Configuration
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PRINCIPLES OF OPERATION
Table 1. Register Selection
DLAB†
A2
A1
A0
0
L
L
L
Receiver buffer (read), transmitter holding register (write)
0
L
L
H
Interrupt enable register
X
L
H
L
Interrupt identification register (read only)
X
L
H
H
Line control register
X
H
L
L
Modem control register
X
H
L
H
Line status register
X
H
H
L
Modem status register
X
H
H
H
Scratch register
1
L
L
L
Divisor latch (LSB)
1
L
L
H
REGISTER
Divisor latch (MSB)
† The divisor latch access bit (DLAB) is the most significant bit of the line control register. The DLAB
signal is controlled by writing to this bit location (see Table 3).
Table 2. ACE Reset Functions
RESET
CONTROL
REGISTER/SIGNAL
Interrupt enable register
RESET
All bits cleared (0 – 3 forced and 4 – 7 permanent)
Interrupt identification register
RESET
Bit 0 is set, bits 1 and 2 are cleared, and bits 3 – 7
are permanently cleared
Line control register
RESET
All bits cleared
Modem control register
RESET
All bits cleared
Line status register
RESET
Bits 5 and 6 are set, all other bits are cleared
Modem status register
RESET
Bits 0 – 3 are cleared, bits 4 – 7 are input signals
SOUT
RESET
High
INTRPT (receiver error flag)
Read LSR/RESET
Low
INTRPT (received data available)
Read RBR/RESET
Low
Read IIR/Write
THR/RESET
Low
INTRPT (transmitter holding register empty)
INTRPT (modem status changes)
14
RESET STATE
Read MSR/RESET
Low
OUT2 (interrupt enable)
RESET
High
RTS
RESET
High
DTR
RESET
High
OUT1
RESET
High
Scratch register
RESET
No effect
Divisor latch (LSB and MSB) registers
RESET
No effect
Receiver buffer registers
RESET
No effect
Transmitter holding registers
RESET
No effect
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PRINCIPLES OF OPERATION
accessible registers
The system programmer, using the CPU, has access to and control over any of the ACE registers that are
summarized in Table 3. These registers control ACE operations, receive data, and transmit data. Descriptions
of these registers are given in Table 3.
Table 3. Summary of Accessible Registers
REGISTER ADDRESS
Bit
No.
0
1
2
O DLAB = 0
O DLAB = 0
Receiver
Buffer
Register
(Read
Only)
Transmitter
Holding
g
Register
(Write
Only)
RBR
Data Bit 0†
Data Bit 1
Data Bit 2
1 DLAB = 0
2
3
4
5
6
7
O DLAB = 1
1 DLAB = 1
Interrupt
p
Enable
Register
Interrupt
p
Ident.
Register
(Read
Only)
Line
Control
Register
Modem
Control
Register
Line
Status
Register
Modem
Status
Register
Scratch
Register
Divisor
Latch
(LSB)
Latch
(MSB)
THR
IER
IIR
LCR
MCR
LSR
MSR
SCR
DLL
DLM
Data Bit 0
Enable
Received
ece ed
Data
Available
Interrupt
(ERBF)
“0” If
Interrupt
Pending
Word
Length
Select
Bit 0
(WLSO)
Data
Terminal
Ready
(DTR)
Data
Ready
(DR)
Delta
Clear
to Send
(DCTS)
Bit 0
Bit 0
Bit 8
Data Bit 1
Enable
a s
e
Transmitter
Holding
g
Register
g
Empty
Interrupt
(ETBE)
Interrupt
ID
Bit (0)
Word
Length
g
Select
Bit 1
(WLS1)
Request
q
to Send
(RTS)
Overrun
Error
(OE)
Delta
Data
Set
Ready
(DDSR)
Bit 1
Bit 1
Bit 9
Data Bit 2
Enable
Receiver
Line Status
Interrupt
(ELSI)
Interrupt
ID
Bit (1)
Number of
Stop Bits
(STB)
Out 1
Parityy
Error
(PE)
Trailing
Edge Ring
Indicator
(TERI)
Bit 2
Bit 2
Bit 10
0
Parity
Enable
(PEN)
Out 2
(Interrupt
Enable)
Framing
Error
(FE)
Delta
Receive
Li
Line
Signal
Detect
(DRLSD)
Bit 3
Bit 3
Bit 11
0
Even
Parityy
Select
(EPS)
Loop
B k
Break
Interrupt
(BI)
Clear
to
Send
(CTS)
Bit 4
Bit 4
Bit 12
0
Stick
Parity
0
Transmitter
Holding
Register
g
(THRE)
Data
Set
Ready
(DSR)
Bit 5
Bit 5
Bit 13
0
Set
S
Break
Ring
Indicator
(RI)
Bit 6
Bit 6
Bit 14
0
Divisor
Latch
Access
Bit
(DLAB)
Receive
Line
Signal
Detect
(RLSD)
Bit 7
Bit 7
Bit 15
3
Data Bit 3
Data Bit 3
Enable
ode
Modem
Status
Interrupt
(EDSSI)
4
Data Bit 4
Data Bit 4
0
5
6
Data Bit 5
Data Bit 6
Data Bit 5
Data Bit 6
0
0
0
Transmitter
Emptyy
(TEMT)
7
Data Bit 7
Data Bit 7
0
0
0
† Bit 0 is the least significant bit. It is the first bit serially transmitted or received.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PRINCIPLES OF OPERATION
interrupt control logic
The interrupt control logic is shown in Figure 10.
DR (LSR Bit 0)
ERBFI (IER Bit 0)
THRE (LSR bit 5)
ETBEI (IER Bit 1)
OE (LSR bit 1)
Interrupt
Output
PE (LSR Bit 2)
FE (LSR bit 3)
BI (LSR Bit 4)
ELSI (IER Bit 1)
DCTS (MSR Bit 0)
DDSR (MSR Bit 1)
TERI (MSR Bit 2)
DRLSD (MSR Bit 3)
EDSSI (IER Bit 3)
INTERRUPT ENABLE (MCR Bit 3)
Figure 10. Interrupt Control Logic
interrupt enable register (IER)
The IER enables each of the four types of interrupts (refer to Table 4) and the INTRPT output signal in response
to an interrupt generation. The IER can also disable the interrupt system by clearing bits 0 through 3. The
contents of this register are summarized in Table 3 and are described in the following bulleted list.
D
D
D
D
D
16
Bit 0: This bit, when set, enables the received data available interrupt.
Bit 1: This bit, when set, enables the THRE interrupt.
Bit 2: This bit, when set, enables the receiver line status interrupt.
Bit 3: This bit, when set, enables the modem status interrupt.
Bits 4 thru 7: These bits in the IER are not used and are always cleared.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PRINCIPLES OF OPERATION
interrupt identification register (IIR)
The ACE has an on-chip interrupt generation and prioritization capability that permits a flexible interface with
most microprocessors.
The ACE provides four prioritized levels of interrupts:
D
D
D
D
Priority 1 – Receiver line status (highest priority)
Priority 2 – Receiver data ready or receiver character time out
Priority 3 – Transmitter holding register empty
Priority 4 – Modem status (lowest priority)
When an interrupt is generated, the IIR indicates that an interrupt is pending and indicates the type of interrupt
in its three least significant bits (bits 0, 1, and 2). The contents of this register are summarized in Table 3 and
described in Table 4.
D
D
D
Bit 0: This bit can be used either in a hardwire prioritized or polled interrupt system. When this bit is cleared,
an interrupt is pending. When bit 0 is set, no interrupt is pending.
Bits 1 and 2: These two bits identify the highest priority interrupt pending as indicated in Table 4.
Bits 3 – 7: These bits in the interrupt identification register are not used and are always clear.
Table 4. Interrupt Control Functions
INTERRUPT
IDENTIFICATION
REGISTER
BIT 2
BIT 1
BIT 0
0
0
1
PRIORITY
LEVEL
INTERRUPT TYPE
None
None
INTERRUPT SOURCE
INTERRUPT RESET
METHOD
None
–
1
1
0
1
Receiver line status
Overrun error,, parity
y error,,
framing
g error or break
interrupt
1
0
0
2
Received data available
Receiver data available
Reading
g the receiver buffer
register
Reading the line status
register
0
1
0
3
Transmitter holding register
empty
Transmitter holding register
empty
Reading
g the interrupt
Identification register
g
((if
source of interrupt)) or writing
g
into the transmitter holding
g
register
0
0
0
4
Modem status
Clear to send, data set
ready, ring indicator, or data
carrier detect
Reading the modem status
register
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PRINCIPLES OF OPERATION
Iine control register (LCR)
The system programmer controls the format of the asynchronous data communication exchange through the
LCR. In addition, the programmer is able to retrieve, inspect, and modify the contents of the LCR; this eliminates
the need for separate storage of the line characteristics in system memory. The contents of this register are
summarized in Table 3 and are described in the following bulleted list.
D
Bits 0 and 1: These two bits specify the number of bits in each transmitted or received serial character.
These bits are encoded as shown in Table 5.
Table 5. Serial Character Word Length
D
Bit 1
Bit 0
Word Length
0
0
5 bits
0
1
6 bits
1
0
7 bits
1
1
8 bits
Bit 2: This bit specifies either one, one and one-half, or two stop bits in each transmitted character. When
bit 2 is cleared, one stop bit is generated in the data. When bit 2 is set, the number of stop bits generated
is dependent on the word length selected with bits 0 and 1. The number of stop bits generated in relation
to word length and bit 2 is as shown in Table 6.
Table 6. Number of Stop Bits Generated
D
D
D
D
D
18
Bit 2
Word Length Selected
by Bits 1 and 2
Number of Stop
Bits Generated
0
Any word length
1
1
5 bits
1 1/2
1
6 bits
2
1
7 bits
2
1
8 bits
2
Bit 3: This bit is the parity enable bit. When bit 3 is set, a parity bit is generated in transmitted data between
the last data word bit and the first stop bit. In received data, when bit 3 is set, parity is checked. When bit
3 is cleared, no parity is generated or checked.
Bit 4: This bit is the even parity select bit. When parity is enabled (bit 3 is set) and bit 4 is set, even parity
(an even number of logic is in the data and parity bits) is selected. When parity is enabled and bit 4 is cleared,
odd parity (an odd number of logic 1s) is selected.
Bit 5: This is the stick parity bit. When bits 3, 4, and 5 are set, the parity bit is transmitted and checked as
cleared. When bits 3 and 5 are set and bit 4 is cleared, the parity bit is transmitted and checked as set.
Bit 6: This bit is the break control bit. Bit 6 is set to force a break condition, i.e, a condition where SOUT
terminal is forced to the spacing (cleared) state. When bit 6 is cleared, the break condition is disabled. The
break condition has no affect on the transmitter logic, it only affects the serial output.
Bit 7: This bit is the divisor latch access bit (DLAB). Bit 7 must be set to access the divisor latches of the
baud generator during a read or write. Bit 7 must be cleared during a read or write to access the receiver
buffer, the THR, or the IER.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PRINCIPLES OF OPERATION
line status register (LSR)†
The LSR provides information to the CPU concerning the status of data transfers. The contents of this register
are summarized in Table 3 and are described in the following bulleted list.
D
Bit 0: This bit is the data ready (DR) indicator for the receiver. Bit 0 is set whenever a complete incoming
character has been received and transferred into the RBR and is cleared by reading the RBR.
D
Bit 1‡: This bit is the overrun error (OE) indicator. When bit 1 is set, it indicates that before the character
in the RBR was read, it was overwritten by the next character transferred into the register. The OE indicator
is cleared every time the CPU reads the contents of the LSR.
D
Bit 2‡: This bit is the parity error (PE) indicator. When bit 2 is set, it indicates that the parity of the received
data character does not match the parity selected in the LCR (bit 4). The PE bit is cleared every time the
CPU reads the contents of the LSR.
D
Bit 3‡: This bit is the framing error (FE) indicator. When bit 3 is set, it indicates that the received character
did not have a valid (set) stop bit. The FE bit is cleared every time the CPU reads the contents of the LSR.
D
Bit 4‡: This bit is the break interrupt (BI) indicator. When bit 4 is set, it indicates that the received data input
was held clear for longer than a full-word transmission time. A full-word transmission time is defined as the
total time of the start, data, parity, and stop bits. The BI bit is cleared every time the CPU reads the contents
of the LSR.
D
D
D
Bit 5: This bit is the THRE indicator. Bit 5 is set when the THR is empty, indicating that the ACE is ready
to accept a new character. If the THRE interrupt is enabled when the THRE bit is set, then an interrupt is
generated. THRE is set when the contents of the THR are transferred to the transmitted shift register. This
bit is cleared concurrent with the loading of the THR by the CPU.
Bit 6: This bit is the transmitter empty (TEMT) indicator, bit 6 is set when the THR and the transmitter shift
register are both empty. When either the THR or the transmitter shift register contains a data character, the
TEMT bit is cleared.
Bit 7: This bit is always clear.
† The line status register is intended for read operations only; writing to this register is not recommended outside of a factory testing environment.
‡ Bits 1 through 4 are the error conditions that produce a receiver line status interrupt.
modem control register (MCR)
The MCR is an 8-bit register that controls an interface with a modem, data set, or peripheral device that is
emulating a modem. The contents of this register are summarized in Table 3 and are described in the following
bulleted list.
D
D
D
D
Bit 0: This bit (DTR) controls the data terminal ready (DTR) output. Setting bit 0 forces the DTR output to
its active state (low). When bit 0 is cleared, DTR goes high.
Bit 1: This bit (RTS) controls the request to send (RTS) output in a manner identical to bit 0’s control over
the DTR output.
Bit 2: This bit (OUT 1) is a reserved location used only in the loopback mode.
Bit 3: This bit (OUT 2) controls the output enable for the interrupt signal. When set, the interrupt is enabled.
When bit 3 is cleared, the interrupt is disabled.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PRINCIPLES OF OPERATION
modem control register (MCR) (continued)
D
Bit 4: This bit provides a local loopback feature for diagnostic testing of the ACE. When this bit is set, the
following occurs:
1.
2.
3.
4.
5.
The SOUT is asserted high.
The SIN is disconnected.
The output of the transmitter shift register is looped back into the receiver shift register input.
The four modem status inputs (CTS, DSR, RLSD, and RI) are disconnected.
The MCR bits (DTR, RTS, OUT1, and OUT2) are connected to the modem status register bits (DSR,
CTS, RI, and RLSD), respectively.
6. The four modem control output terminals are forced to their inactive states (high).
In the diagnostic mode, data that is transmitted is immediately received. This allows the processor to verify
the transmit and receive data paths to the ACE. The receiver and transmitter interrupts are fully operational.
The modem control interrupts are also operational but the modem control interrupt sources are now the
lower four bits of the MCR instead of the four modem control inputs. All interrupts are still controlled by the
IER.
D
Bits 5 through 7: These bits are always cleared.
modem status register (MSR)
The MSR is an 8-bit register that provides information about the current state of the control lines from the
modem, data set, or peripheral device to the CPU. Additionally, four bits of this register provides change
information; when a control input from the modem changes state the appropriate bit is set. All four bits are
cleared when the CPU reads the MSR. The contents of this register are summarized in Table 3 and are
described in the following bulleted list.
D
D
D
D
D
D
D
D
20
Bit 0. This bit is the delta clear to send (DCTS) indicator. Bit 0 indicates that the CTS input has changed
states since the last time it was read by the CPU. When this bit is set and the modem status Interrupt is
enabled, a modem status interrupt is generated.
Bit 1. This bit is the delta data set ready (DDSR) indicator. Bit 1 indicates that the DSR input has changed
states since the last time it was read by the CPU. When this bit is set and the modem status Interrupt is
enabled, a modem status interrupt is generated.
Bit 2. This bit is the trailing edge of ring indicator (TERI) detector. Bit 2 indicates that the RI input to the chip
has changed from a low to a high state. When this bit is set and the modem status Interrupt is enabled, a
modem status interrupt is generated.
Bit 3. This bit is the delta receive line signal detect (DRLSD) indicator. Bit 3 indicates that the RLSD input
to the chip has changed states since the last time it was read by the CPU. When this bit is set and the modem
status interrupt is enabled, a modem status interrupt is generated.
Bit 4. This bit is the complement of the clear to send (CTS) input. When bit 4 (loop) of the MCR is set, bit
4 is equivalent to the MCR bit 1 (RTS).
Bit 5. This bit is the complement of the data set ready (DSR) input. When bit 4 (loop) of the MCR is set, bit
5 is equivalent to the MCR bit 0 (DTR).
Bit 6. This bit is the complement of the ring indicator (RI) input. When bit 4 (loop) of the MCR is set, bit 6
is equivalent to the MCR bit 2 (OUT 1).
Bit 7. This bit is the complement of the receive line signal detect (RLSD) input. When bit 4 (loop) of the MCR
is set, bit 7 is equivalent to the MCR bit 3 (OUT 2).
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PRINCIPLES OF OPERATION
parallel port registers
The parallel port registers interface either device to a Centronix-style printer interface. When chip select 2 (CS2)
is low, the parallel port is selected. Tables 7 and 8 show the registers associated with this parallel port. The read
or write function of the register is controlled by the state of the read (IOR) and write (IOW) terminal as shown.
The read data register allows the microprocessor to read the information on the parallel bus.
The read status register allows the microprocessor to read the status of the printer in the five most significant
bits. The status bits are printer busy (BUSY), acknowledge (ACK) which is a handshake function, paper empty
(PE), printer selected (SLCT), and error (ERROR). The read control register allows the state of the control lines
to be read. The write control register sets the state of the control lines, which are interrupt enable (IRQ ENB),
select in (SLIN), initialize the printer (INIT), autofeed the paper (AFD), and strobe (STB), which informs the
printer of the presence of a valid byte on the parallel bus. These signals are cleared when a reset occurs. The
write data register allows the microprocessor to write a byte to the parallel bus. The parallel port is completely
compatible with the parallel port implementation used in the IBM serial/parallel adaptor.
Table 7. Parallel Port Registers
REGISTER BITS
REGISTER
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
Read status
BUSY
ACK
PE
SLCT
ERROR
1
1
1
Read control
1
1
1
IRQ ENB
SLIN
INIT
AFD
STB
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
1
1
1
IRQ ENB
SLIN
INIT
AFD
STB
Read data
Write data
Write control
Table 8. Parallel Port Register Select
CONTROL TERMINALS
A0
REGISTER SELECTED
IOR
IOW
CS2
A1
L
H
L
L
L
Read data
L
H
L
L
H
Read status
L
H
L
H
L
Read control
L
H
L
H
H
Invalid
H
L
L
L
L
Write data
H
L
L
L
H
Invalid
H
L
L
H
L
Write control
H
L
L
H
H
Invalid
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
TL16C451, TL16C452
ASYNCHRONOUS COMMUNICATIONS ELEMENTS
SLLS053C – MAY 1989 – REVISED AUGUST 1999
PRINCIPLES OF OPERATION
programmable baud generator
The ACE contains a programmable baud generator that takes a clock input in the range between dc and 9 MHz
and divides it by a divisor in the range between 1 and (216 – 1). The output frequency of the baud generator is
sixteen times (16 ×) the baud rate. The formula for the divisor is:
divisor # = CLK frequency input ÷ (desired baud rate × 16)
Two 8-bit registers, called divisor latches, store the divisor in a 16-bit binary format. These divisor latches must
be loaded during initialization of the ACE in order to ensure desired operation of the baud generator. When either
of the divisor latches is loaded, a 16-bit baud counter is also loaded to prevent long counts on initial load. For
baud rates of 38.4 kilobits per second and below, the error obtained is very small. The accuracy of the selected
baud rate is dependent on the selected crystal frequency.
receiver buffer register (RBR)
The ACE receiver section consists of a receiver shift register and an RBR. Timing is supplied by the 16× receiver
clock (RCLK). Receiver section control is a function of the ACE line control register.
The ACE receiver shift register receives serial data from the serial input (SIN) terminal. The receiver shift
register then converts the data to a parallel form and loads it into the RBR. When a character is placed in the
RBR and the received data available interrupt is enabled, an interrupt is generated. This interrupt is cleared
when the data is read out of the RBR.
scratch register
The scratch register is an 8-bit register that is intended for programmer use as a scratchpad, in the sense that
it temporarily holds programmer data without affecting any other ACE operation.
transmitter holding register (THR)
The ACE transmitter section consists of a THR and a transmitter shift register. Timing is supplied by the baud
out (BAUDOUT) clock signal. Transmitter section control is a function of the ACE line control register.
The ACE THR receives data off of the internal data bus and, when the shift register is idle, moves it into the
transmitter shift register. The transmitter shift register serializes the data and outputs it at the serial output
(SOUT). When the THR is empty and the transmitter holding register empty (THRE) interrupt is enabled, an
interrupt is generated. This interrupt is cleared when a character is loaded into the register.
22
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
20-Mar-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TL16C451FN
ACTIVE
PLCC
FN
68
18
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TL16C451FNG4
ACTIVE
PLCC
FN
68
18
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TL16C451FNR
ACTIVE
PLCC
FN
68
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TL16C451FNRG4
ACTIVE
PLCC
FN
68
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TL16C452FN
ACTIVE
PLCC
FN
68
18
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TL16C452FNG4
ACTIVE
PLCC
FN
68
18
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TL16C452FNR
ACTIVE
PLCC
FN
68
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
TL16C452FNRG4
ACTIVE
PLCC
FN
68
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated