TLV320AIC33 SLAS480A – JANUARY 2006 – REVISED JULY 2006 LOW POWER STEREO AUDIO CODEC FOR PORTABLE AUDIO/TELEPHONY FEATURES • • • • • • • • • • • • • • • – – Stereo Audio DAC – 100-dBA Signal-to-Noise Ratio – 16/20/24/32-Bit Data – Supports Rates From 8 kHz to 96 kHz – 3D/Bass/Treble/EQ/De-emphasis Effects Stereo Audio ADC – 92-dBA Signal-to-Noise Ratio – Supports Rates From 8 kHz to 96 kHz Ten Audio Input Pins – Programmable in Single-Ended or Fully Differential Configurations – 3-State Capability for Floating Input Configurations Seven Audio Output Drivers – Stereo 8-Ω, 500-mW/Channel Speaker Drive Capability – Stereo Fully Differential or Single-Ended Headphone Drivers – Fully Differential Stereo Line Outputs – Fully Differential Mono Output Low Power: 14-mW Stereo 48-kHz Playback With 3.3-V Analog Supply Programmable Input/Output Analog Gains Automatic Gain Control (AGC) for Record Programmable Microphone Bias Level Programmable PLL for Flexible Clock Generation Control Bus Selectable SPI or I2C Audio Serial Data Bus Supports I2S, Left/Right-Justified, DSP, and TDM Modes Alternate Serial PCM/I2S Data Bus for Easy Connection to Bluetooth™ Module Digital Microphone Input Support Extensive Modular Power Control Power Supplies: Analog: 2.7 V–3.6 V. Digital Core: 1.525 V–1.95 V – Digital I/O: 1.1 V–3.6 V • Packages: 5 × 5 mm 80-VFBGA; 7 × 7 mm 48-QFN DESCRIPTION The TLV320AIC33 is a low power stereo audio codec with stereo headphone amplifier, as well as multiple inputs and outputs programmable in single-ended or fully differential configurations. Extensive register- based power control is included, enabling stereo 48-kHz DAC playback as low as 14 mW from a 3.3-V analog supply, making it ideal for portable battery-powered audio and telephony applications. The record path of the TLV320AIC33 contains integrated microphone bias, digitally controlled stereo microphone preamplifier, and automatic gain control (AGC), with mix/mux capability among the multiple analog inputs. The playback path includes mix/mux capability from the stereo DAC and selected inputs, through programmable volume controls, to the various outputs. The TLV320AIC33 contains four high-power output drivers as well as three fully differential output drivers. The high-power output drivers are capable of driving a variety of load configurations, including up to four channels of single-ended 16-Ω headphones using ac-coupling capacitors, or stereo 16-Ω headphones in a capacitorless output configuration. In addition, pairs of drivers can be used to drive 8-Ω speakers in a BTL configuration at 500 mW per channel. The stereo audio DAC supports sampling rates from 8 kHz to 96 kHz and includes programmable digital filtering in the DAC path for 3D, bass, treble, midrange effects, speaker equalization, and de-emphasis for 32-kHz, 44.1-kHz, and 48-kHz rates. The stereo audio ADC supports sampling rates from 8 kHz to 96 kHz and is preceded by programmable gain amplifiers providing up to +59.5-dB analog gain for low-level microphone inputs. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. MIcroStar Junior is a trademark of Texas Instruments. Bluetooth is a trademark of Bluetooth SIG, Inc.. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2006, Texas Instruments Incorporated TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 DESCRIPTION (CONTINUED) The serial control bus supports SPI or I2C protocols, while the serial audio data bus is programmable for I2S, left/right-justified, DSP, or TDM modes. A highly programmable PLL is included for flexible clock generation and support for all standard audio rates from a wide range of available MCLKs, varying from 512 kHz to 50 MHz, with special attention paid to the most popular cases of 12-MHz, 13-MHz, 16-MHz, 19.2-MHz, and 19.68-MHz system clocks. The TLV320AIC33 operates from an analog supply of 2.7 V–3.6 V, a digital core supply of 1.525 V–1.95 V, and a digital I/O supply of 1.1 V–3.6 V. The device is available in 5 × 5-mm, 80-ball MIcroStar Junior™ BGA and 7 × 7-mm, 48-lead QFN. 2 Submit Documentation Feedback Submit Documentation Feedback MIC2/LINE2R+ MIC2/LINE2R− DAC R Volume Ctl & Effects ADC SPI / I2C Serial Control Bus DAC L Volume Ctl & Effects ADC Audio Clock Generation PGA 0/+59.5dB 0.5dB steps PGA 0/+59.5dB 0.5dB steps WCLK Audio Serial Bus DIN DOUT BCLK SDA/GPIO SCL/GPIO MISO/GPIO MOSI/GPIO SCLK/I2C_ADR1 CSEL/I2C_ADR0 SELECT RESETB GPIO_2 GPIO_1 MCLK Bias/ Reference + MIC1/LINE1R+ MIC1/LINE1R− MIC3/LINE3R + MIC1/LINE1L+ MIC1/LINE1L− MIC3/LINE3L MIC2/LINE2L+ MIC2/LINE2L− AVDD_ADC AVSS_ADC AVDD_DAC AVSS_DAC DRVDD DRVSS DRVDD DRVSS DVDD DVSS IOVDD Voltage Supplies VCM VCM + + + + + + + MICBIAS MICDET MONO_OUT− MONO_OUT+ LINE_OUT_R− LINE_OUT_R+ LINE_OUT_L− LINE_OUT_L+ HPR+ HPR−/HPRCOM/ SPKFC HPL−/HPLCOM HPL+ TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 SIMPLIFIED BLOCK DIAGRAM 3 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 PACKAGING/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DESIGNATOR OPERATING TEMPERATURE RANGE ORDERING NUMBER ZQE BGA-80 TLV320AIC33 GQE QFN-48 –40°C to 85°C RGZ TRANSPORT MEDIA, QUANTITY TLV320AIC33IZQE Trays, 360 TLV320AIC33IZQER Tape and Reel, 3000 TLV320AIC33IGQE Trays, 360 TLV320AIC33IGQER Tape and Reel, 3000 TLV320AIC33IRGZT Tape and Reel, 250 TLV320AIC33IRGZR Tape and Reel, 2000 PIN ASSIGNMENTS 1 12 13 48 J H G F E D C B 37 24 A 25 36 1 48−lead QFN Package (Bottom view) 2 3 5 6 7 8 9 5x5mm 80−Ball BGA Package (Bottom View) (Not to scale) TERMINAL FUNCTIONS TERMINAL 4 4 DESCRIPTION BGA BALL QFN A2 13 MICBIAS Microphone Bias Voltage Output A1 14 MIC3R MIC3 Input (Right or Multifunction) C2,D2 15 AVSS_ADC Analog ADC Ground Supply, 0 V B1,C1 16,17 DRVDD ADC Analog and Output Driver Voltage Supply, 2.7 V–3.6 V D1 18 HPLOUT High-Power Output Driver (Left Plus) E1 19 HPLCOM High-Power Output Driver (Left Minus or Multifunctional) E2,F2 20,21 DRVSS Analog Output Driver Ground Supply, 0 V F1 22 HPRCOM High-Power Output Driver (Right Minus or Multifunctional) G1 23 HPROUT High-Power Output Driver (Right Plus) H1 24 DRVDD ADC Analog and Output Driver Voltage Supply, 2.7 V– 3.6 V NAME J1 25 AVDD Analog DAC Voltage Supply, 2.7 V–3.6 V G2,H2 26 AVSS_DAC Analog DAC Ground Supply, 0 V J2 27 MONO_LOP Mono Line Output (Plus) Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 PIN ASSIGNMENTS (continued) TERMINAL FUNCTIONS (continued) TERMINAL DESCRIPTION BGA BALL QFN J3 28 MONO_LOM Mono Line Output (Minus) J4 29 LEFT_LOP Left Line Output (Plus) J5 30 LEFT_LOM Left Line Output (Minus) J6 31 RIGHT_LOP Right Line Output (Plus) NAME J7 32 RIGHT_LOM Right Line Output (Minus)t H8 33 RESET Reset J8 34 GPIO2 General-Purpose Input/Output #2 (Input/Output) / Digital Microphone Data Input / PLL Clock Input / Audio Serial Data Bus Bit Clock Input/Output J9 35 GPIO1 General-Purpose Input/Output #1 (Input/Output) / PLL/Clock Mux Output / Short Circuit Interrupt / AGC Noise Flag / Digital Microphone Clock Audio Serial Data Bus Word Clock Input/Output H9 36 DVDD Digital Core Voltage Supply, 1.525V – 1.95V G8 37 MCLK Master Clock Inputt G9 38 BCLK Audio Serial Data Bus Bit Clock (Input/Output) F9 39 WCLK Audio Serial Data Bus Word Clock (Input/Output) E9 40 DIN Audio Serial Data Bus Data Input (Input) F8 41 DOUT Audio Serial Data Bus Data Output (Output)t D9 42 DVSS Digital Core / I/O Ground Supply, 0V E8 43 SELECT Control Mode Select Pin (1=SPI, 0=I2C) C9 44 IOVDD I/O Voltage Supply, 1.1V – 3.6V B8 45 MFP0 Multifunction pin #0 - SPI Chip Select / GPI / I2C Address Pin #0 B9 46 MFP1 Multifunction pin #1 - SPI Serial Clock / GPI / I2C Address Pin #1S A8 47 MFP2 Multifunction pin #2 - SPI MISO Slave Serial Data Output / GPOI A9 48 MFP3 Multifunction pin #3 - SPI MOSI Slave Serial Data Input / GPI / Audio Serial Data Bus Data Input C8 1 SCL I2C Serial Clock / GPIO D8 2 SDA I2C Serial Data Input/Output / GPIO A7 NC No Connect A6 3 LINE1LP MIC1 or Line1 Analog Input (Left Plus or Multifunction) A5 4 LINE1LM MIC1 or Line1 Analog Input (Left Minus or Multifunction)I B7 5 LINE1RP MIC1 or Line1 Analog Input (Right Plus or Multifunction)I B6 6 LINE1RM MIC1 or Line1 Analog Input (Right Minus or Multifunction) A4 7 LINE2LP MIC2 or Line2 Analog Input (Left Plus or Multifunction) B5 8 LINE2LM MIC2 or Line2 Analog Input (Left Minus or Multifunction)I B4 9 LINE2RP MIC2 or Line2 Analog Input (Right Plus or Multifunction)I A3 10 LINE2RM MIC2 or Line2 Analog Input (Right Minus or Multifunction)I B3 11 MIC3L MIC3 Input (Left or Multifunction) B2 12 MICDET Microphone Detect Submit Documentation Feedback 5 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) (2) TJ Max VALUE UNIT AVDD to AVSS, DRVDD to DRVSS –0.3 to 3.9 V AVDD to DRVSS –0.3 to 3.9 V IOVDD to DVSS –0.3 to 3.9 V DVDD to DVSS –0.3 to 2.5 V AVDD to DRVDD –0.1 to 0.1 V Digital input voltage to DVSS –0.3 V to IOVDD+0.3 V Analog input voltage to AVSS –0.3 V to AVDD+0.3 V Operating temperature range -40 to +85 °C Storage temperature range -65 to +105 °C 105 °C Junction temperature (TJ Max – TA) / θJA Power dissipation θJA (1) (2) Thermal impedance , BGA package 63 °C/W Thermal impedance, QFN package 38.5 °C/W Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. ESD complicance tested to EIA / JESD22-A114-B and passed. DISSIPATION RATINGS (1) (1) Package Type TA = 25°C POWER RATING DERATING FACTOR TA = 75°C POWER RATING TA = 85°C POWER RATING BGA 1.27 W 15.9 mW/°C 476 mW 317 mW QFN 2.08 W 26.0 mW/°C 779 mW 519 mW This data was taken using 2 oz. trace and copper pad that is soldered directly to a JEDEC standard 4-layer 3 in × 3 in PCB. RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) AVDD, Analog supply voltage DRVDD1 (1) /2 DVDD (1) Digital core supply voltage IOVDD (1) Digital I/O supply voltage VI Analog full-scale 0 dB input voltage (DRVDD1 = 3.3 V) MIN NOM MAX 2.7 3.3 3.6 V 1.525 1.8 1.95 V 1.8 3.6 1.1 0.707 Stereo line-output load resistance 10 Stereo headphone-output load resistance 16 Digital output load capacitance TA (1) 6 kΩ Ω –40 Analog voltage values are with respect to AVSS1, AVSS2, DRVSS; digital voltage values are with respect to DVSS. Submit Documentation Feedback V VRMS 10 Operating free-air temperature UNIT pF 85 °C TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 ELECTRICAL CHARACTERISTICS At 25°C, AVDD, DRVDD, IOVDD = 3.3 V, DVDD = 1.8 V, Fs = 48-kHz, 16-bit audio data (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT AUDIO ADC THD Input signal level (0-dB) Single-ended input Signal-to-noise ratio, A-weighted (1) (2) Fs = 48 kHz, 0 dB PGA gain, MIC1/LINE1 inputs selected and AC-shorted to ground Dynamic range, A-weighted (1) (2) Fs = 48 kHz, 1-kHz –60 dB full-scale input applied at MIC1/LINE1 inputs, 0-dB PGA gain Total harmonic distortion Fs = 48 kHz, 1-kHz –2dB full-scale input applied at MIC1/LINE1 inputs, 0-dB PGA gain Power supply rejection ratio –90 –75 dB 0.003% 0.017% dB –80 –99 1 kHz, –2 dB MIC1L to MIC1R –-73 1-kHz input tone, RSOURCE < 50 Ω dB 0.7 dB 59.5 dB 0.5 dB MIC1/LINE1 inputs, routed to single ADC Input mix attenuation = 0 dB 20 MIC2/LINE2 inputs, input mix attenuation = 0 dB 20 MIC3/LINE3 inputs, input mix attenuation = 0 dB 20 MIC1/LINE1 inputs, input mix attenuation = –12 dB 80 MIC2/LINE2 inputs, input mix attenuation = –12 dB 80 MIC3/LINE3 inputs, input mix attenuation = –12 dB 80 MIC1/LINE1 inputs kΩ 10 pF Input level control minimum attenuation setting 0 dB Input level control maximum attenuation setting 12 dB Input level control attenuation step size 1.5 dB ADC DIGITAL DECIMATION FILTER, Fs = 48 kHz Filter gain from 0 to 0.39 Fs Filter gain at 0.4125 Fs Filter gain at 0.45 Fs Filter gain at 0.5 Fs Filter gain from 0.55 Fs to 64 Fs Filter group delay (2) dB 1 kHz, –2 dB MIC2L to MIC2R ADC programmable gain amplifier step size (1) 92 68 ADC programmable gain amplifier maximum gain Input capacitance dB 234 Hz, 100mVpp on AVDD, DRVDD, differential input 1 kHz input, 0 dB PGA gain VRMS 92 46 ADC gain error Input resistance 80 234 Hz, 100 mVpp on AVDD, DRVDD, single-ended input 1 kHz, –2 dB MIC3L to MIC3R ADC channel separation 0.707 ±0.1 dB –0.25 dB –3 dB –17.5 dB –75 dB 17/Fs Sec Ratio of output level with 1-kHz full-scale sine wave input, to the output level with the inputs short circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer. All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values. Submit Documentation Feedback 7 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 ELECTRICAL CHARACTERISTICS (continued) At 25°C, AVDD, DRVDD, IOVDD = 3.3 V, DVDD = 1.8 V, Fs = 48-kHz, 16-bit audio data (unless otherwise noted) PARAMETER TEST CONDITIONS MIN Programmable settings, load = 750 Ω 2.25 TYP MAX UNIT MICROPHONE BIAS 2.0 Bias voltage 2.5 2.75 V AVDD0.2 Current sourcing AUDIO DAC 2.5 V setting 0-dB gain to line outputs. DAC output common-mode setting = 1.35 V, output level control gain = 0-dB Signal-to-noise ratio, A-weighted (3) Fs = 48 kHz, 0-dB gain to line outputs, zero signal applied, referenced to full-scale input level Dynamic range, A-weighted 100 dB Fs = 48 kHz, 0-dB gain to line outputs, 1 kHz –60 dB signal applied 100 dB Total harmonic distortion Fs = 48 kHz, 1 kHz 0 dB input signal applied –93 Power supply rejection ratio 234 Hz, 100 mVpp on AVDD, DRVDD1/2 DAC channel separation (left to right) 1-kHz, 0-dB DAC interchannel gain mismatch DAC Gain Error dB –100 dB 1 kHz input, 0dB gain 0.1 dB 1 kHz input, 0dB gain –0.4 dB Fs = 48-kHz High-pass filter disabled High-pass filter disabled 0.45×Fs ±0.06 Transition band 0.45×Fs Stopband 0.55×Fs Programmable output common mode voltage (applicable to Line Outputs also) –75 dB Passband ripple 0-dB full-scale output voltage Hz dB 0.55×Fs Hz 7.5×Fs Hz 65 dB 21/Fs Sec 0.707 VRMS AC-coupled output configuration (4) 0-dB gain to high power outputs. Output common-mode voltage setting = 1.35 V First option 1.35 Second option 1.50 Third option 1.65 Fourth option V 1.8 Maximum programmable output level control gain 9 dB Programmable output level control gain step size 1 dB Maximum output power RL = 32 Ω 15 RL = 16 Ω 30 Signal-to-noise ratio, A-weighted (5) 8 90 81 Passband STEREO HEADPHONE DRIVER (5) VRMS VPP Group delay (4) 1.414 4.0 Stopband attenuation (3) mA Differential Line output, load = 10 kΩ, 50 pF Full-scale differential output voltage DAC DIGITAL INTERPOLATION FILTER PO 4 94 mW dB Unless otherwise noted, all measurements use output common-mode voltage setting of 1.35 V, 0-dB output level control gain, 16-Ω single-ended load. Unless otherwise noted, all measurements use output common-mode voltage setting of 1.35 V, 0-dB output level control gain, 16-Ω single-ended load. Ratio of output level with a 1-kHz full-scale input, to the output level playing an all-zero signal, measured A-weighted over a 20-Hz to 20-kHz bandwidth. Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 ELECTRICAL CHARACTERISTICS (continued) At 25°C, AVDD, DRVDD, IOVDD = 3.3 V, DVDD = 1.8 V, Fs = 48-kHz, 16-bit audio data (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT –77 1-kHz output, PO = 5 mW, RL = 32 Ω 0.014 –76 1-kHz output, PO = 10 mW, RL = 32 Ω 0.016 Total harmonic distortion dB% –73 1-kHz output, PO = 10 mW, RL = 16 Ω 0.022 –71 1-kHz output, PO = 20 mW, RL = 16 Ω 0.028 Channel separation 1 kHz, 0 dB input 90 dB Power supply rejection ratio 217 Hz, 100 mVpp on AVDD, DRVDD1/2 48 dB Mute attenuation 1-kHz output 107 dB DIGITAL I/O VIL Input low level IIL = +5-µA –0.3 VIH Input high level (6) IIH = +5-µA 0.7 × IOVDD VOL Output low level IIH = 2 TTL loads VOH Output high level IOH = 2 TTL loads SUPPLY CURRENT Stereo line playback Mono record Stereo record PLL AVDD+DRVDD DVDD AVDD+DRVDD DVDD AVDD+DRVDD DVDD AVDD+DRVDD DVDD DVDD AVDD+DRVDD Power down (6) V V 0.1 × IOVDD 0.8 × IOVDD V V Fs = 48-kHz AVDD+DRVDD Headphone amplifier 0.3 × IOVDD DVDD Fs = 48-kHz, PLL off, headphone drivers off, DAC direct mode Fs = 48-kHz, PLL and AGC off Fs = 48-kHz, PLL and AGC off 3.0 2.0 2.2 1.1 4.2 1.3 Additional power consumed when PLL is powered 1.2 LINE2LP/RP only routed to stereo single-ended headphones, DAC and PLL off, no signal applied 5.6 All supply voltages applied, all blocks programmed in lowest power state 0.1 1 0 0.5 mA mA mA mA mA µA When IOVDD < 1.6V, minimum VIH is 1.1V. Submit Documentation Feedback 9 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 AUDIO DATA SERIAL INTERFACE TIMING DIAGRAM WCLK td(WS) td(DO-BCLK) td(DO-WS) BCLK SDOUT th(DI) ts(DI) SDIN Figure 1. I2S/LJF/RJF Timing in Master Mode TIMING CHARACTERISTICS (1) All specifications typical at 25°C, DVDD = 1.8 V IOVDD = 1.1 V PARAMETER MIN IOVDD = 3.3 V MAX MIN MAX UNIT td (WS) ADWS/WCLK delay time 50 15 ns td (DO-WS) ADWS/WCLK to DOUT delay time 50 20 ns td (DO-BCLK) BCLK to DOUT delay time 50 15 ns ts(DI) DIN setup time 10 6 ns th(DI) DIN hold time 10 6 ns tr Rise time 30 10 ns tf Fall time 30 10 ns (1) All timing specifications are measured at characterization but not tested at final test. WCLK td(WS) td(WS) BCLK td(DO-BCLK) SDOUT ts(DI) SDIN Figure 2. DSP Timing in Master Mode 10 Submit Documentation Feedback th(DI) TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 TIMING CHARACTERISTICS (1) All specifications typical at 25°C, DVDD = 1.8 V IOVDD = 1.1 V PARAMETER td (WS) MIN IOVDD = 3.3 V MAX ADWS/WCLK delay time MIN MAX 50 td (DO-BCLK) BCLK to DOUT delay time 50 UNIT 15 ns 15 ns ts(DI) DIN setup time 10 6 ns th(DI) DIN hold time 10 6 ns tr Rise time 30 10 ns tf Fall time 30 10 ns (1) All timing specifications are measured at characterization but not tested at final test. WCLK th(WS) ts(WS) tL(BCLK) BCLK tH(BCLK) td(DO-BCLK) td(DO-WS) tP(BCLK) SDOUT th(DI) ts(DI) SDIN Figure 3. I2S/LJF/RJF Timing in Slave Mode TIMING CHARACTERISTICS (1) All specifications typical at 25°C, DVDD = 1.8 V IOVDD = 1.1 V PARAMETER MIN IOVDD = 3.3 V MAX MIN MAX UNIT tH (BCLK) BCLK high period 70 35 ns tL (BCLK) BCLK low period 70 35 ns ts(WS) ADWS/WCLK setup time 10 6 ns th(WS) ADWS/WCLK hold time 10 td (DO-WS) ADWS/WCLK to DOUT delay time (for LJF Mode only) td (DO-BCLK) BCLK to DOUT delay time ts(DI) DIN setup time 10 6 th(DI) DIN hold time 10 6 tr Rise time 8 4 ns tf Fall time 8 4 ns (1) 6 ns TBD TBD ns 50 20 ns ns ns All timing specifications are measured at characterization but not tested at final test. Submit Documentation Feedback 11 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 th(WS) th(WS) ts(WS) ts(WS) tL(BCLK) tH(BCLK) td(DO-BCLK) tP(BCLK) ts(DI) Figure 4. DSP Timing in Slave Mode TIMING CHARACTERISTICS (1) All specifications typical at 25°C, DVDD = 1.8 V IOVDD = 1.1 V PARAMETER MIN IOVDD = 3.3 V MAX MIN MAX UNIT tH (BCLK) BCLK high period 70 35 ns tL (BCLK) BCLK low period 70 35 ns ts(WS) ADWS/WCLK setup time 10 8 ns th(WS) ADWS/WCLK hold time 10 8 td (DO-BCLK) BCLK to DOUT delay time ts(DI) DIN setup time 10 6 th(DI) DIN hold time 10 6 tr Rise time 8 4 ns tf Fall time 8 4 ns 0.023 0.025 (1) ns 50 20 ns ns ns All timing specifications are measured at characterization but not tested at final test. TYPICAL CHARACTERISTICS -20 -30 -30 Capless, VDD = 3.6 V -40 -40 AC-Coupled, VDD = 2.7 V AC-Coupled, VDD=3.6V AC-Coupled, VDD=2.7V -50 -50 AC-Coupled, VDD = 3.6 V THD, dB Total Harmonic Distortion - dB -20 -60 Capless, VDD=3.6V Capless, VDD=2.7V -60 -70 -70 Capless, VDD = 2.7 V -80 -80 -90 0.015 0.02 0.025 0.03 0.035 0.04 -90 0.005 Power - W Figure 5. Headphone Power vs THD, 16 Ω Load 12 0.007 0.009 0.011 0.013 0.015 0.017 Power, W 0.019 0.021 Figure 6. Headphone Power vs THD, 32 Ω Load Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 TYPICAL CHARACTERISTICS (continued) 0.00 -20.00 -40.00 dB -60.00 -80.00 -100.00 -120.00 -140.00 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Frequency - kHz Figure 7. DAC to Line Output FFT Plot 0 -20 -40 dB -60 -80 -100 -120 -140 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Frequency - kHz Figure 8. Line Input to ADC FFT Plot Submit Documentation Feedback 13 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 TYPICAL CHARACTERISTICS (continued) -10.00 -20.00 -30.00 VDD = 3.3 V VDD = 2.7 V VDD = 3.6 V THD -40.00 -50.00 -60.00 -70.00 -80.00 -90.00 0.10 0.20 0.30 0.40 0.50 0.60 Power - W Figure 9. Speaker Power vs THD, 8 Ω Load 38 36 SNR - dB 34 32 30 28 26 0 10 20 30 40 PGA Gain Setting - dB Figure 10. ADC SNR vs PGA Gain Setting, –65 dBFS Input 14 Submit Documentation Feedback 50 60 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 TYPICAL CHARACTERISTICS (continued) 1.20 1.10 Gain Error - dB 1.00 0.90 0.80 0.70 0.60 Left ADC Right ADC 0.50 0.40 0 10 20 30 40 50 60 PGA Gain Setting - dB Micbias - V Figure 11. ADC Gain Error vs PGA Gain Setting 3.5 3.4 3.3 3.2 3.1 3 2.9 2.8 2.7 2.6 2.5 2.4 2.3 2.2 2.1 2 1.9 1.8 MICBIAS=AVDD MICBIAS=2.5V MICBIAS=2.0V 2.7 2.8 2.9 3 3.1 3.2 3.3 3.4 3.5 3.6 AVDD - V Figure 12. MICBIAS Output Voltage vs AVDD Submit Documentation Feedback 15 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 TYPICAL CHARACTERISTICS (continued) 3.2 MICBIAS=AVDD 3 Micbias - V 2.8 MICBIAS=2.5V 2.6 2.4 2.2 MICBIAS=2.0V 2 1.8 -45 -35 -25 -15 -5 5 15 25 35 45 55 65 Temp - C Figure 13. MICBIAS Output Voltage vs Ambient Temperature 16 Submit Documentation Feedback 75 85 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 TYPICAL CHARACTERISTICS (continued) TYPICAL CIRCUIT CONFIGURATION IOVDD I2C ADDRESS Multimedia Processor Rp DBB / Modem MFP1 MFP2 MFP0 GPIO1 GPIO2 MFP3 DIN DOUT WCLK BCLK MCLK SCL SDA RESET Rp AVDD (2.7V−3.6V) MICBIAS AVDD_ADC MIC3L 1 kΩ AVDD_DAC 0.47 µF DRVDD DRVDD LINE2LP Handset Mic LINE2LM µF µF µF µF 0.47 µF µF µF µF µF µF 1 kΩ A 0.47 µF LINE1LP IOVDD 1.525−1.95V µF LINE1LM DVDD LINE1RM SELECT MONO_LOP DVSS MONO_LOM AVSS_ADC AVSS_DAC DRVSS DRVSS LEFT_LOM LEFT_LOP HPLOUT HPROUT HPRCOM HPLCOM MIC3R MICDET LINE2RM µF 560 Ω 2 kΩ 0.47 µF HEADSET_MIC µF VBAT A µF 560 Ω Earjack mic and headset speakers (capless) µF D LINE2RP Modem RIGHT_ROP Analog Baseband / LINE1RP RIGHT_ROM Line In / FM IOVDD (1.1−3.3V) A AIC33 PVDD A 4700 pF HEADSET_GND HEADSET_SPKR_R HEADSET_SPKR_L 560 Ω 560 Ω 4700 pF TLV320AIC33 Connections Stereo Speakers with Multiple Audio Processors TPA2012D2 Class−D Spkr Amp PVSS A Figure 14. Typical Connections for Capless Headphone and External Speaker Amp Submit Documentation Feedback 17 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 OVERVIEW The TLV320AIC33 is a highly flexible, low power, stereo audio codec with extensive feature integration, intended for applications in smartphones, PDAs, and portable computing, communication, and entertainment applications. Available in a 5x5mm 80-ball BGA (with 51 balls actually used) and 7x7mm 48-lead QFN, the product integrates a host of features to reduce cost, board space, and power consumption in space-constrained, battery-powered, portable applications. The TLV320AIC33 consists of the following blocks: • Stereo audio multi-bit delta-sigma DAC (8 kHz – 96 kHz) • Stereo audio multi-bit delta-sigma ADC (8 kHz – 96 kHz) • Programmable digital audio effects processing (3-D, bass, treble, mid-range, EQ, de-emphasis) • Six audio inputs • Four high-power audio output drivers (headphone/speaker drive capability) • Three fully differential line output drivers • Fully programmable PLL • Headphone/headset jack detection with interrupt Communication to the TLV320AIC33 for control is pin-selectable (using the SELECT pin) as either SPI or I2C. The SPI interface requires that the Slave Select signal (MFP0) be driven low to communicate with the TLV320AIC33. Data is then shifted into or out of the TLV320AIC33 under control of the host microprocessor, which also provides the serial data clock. The I2C interface supports both standard and fast communication modes, and also enables cascading of up to four multiple codecs on the same I2C bus through the use of two pins for addressing (MFP0, MFP1). HARDWARE RESET The TLV320AIC33 requires a hardware reset after power-up for proper operation. After all power supplies are at their specified values, the RESET pin must be driven low for at least 10 ns. If this reset sequence is not performed, the 'AIC33 may not respond properly to register reads/writes. DIGITAL CONTROL SERIAL INTERFACE The TLV320AIC33 control interface supports SPI or I2C communication protocols, with the protocol selectable using the SELECT pin. For SPI, SELECT should be tied high; for I2C, SELECT should be tied low. It is not recommended to change the state of SELECT during device operation. SPI CONTROL MODE /SS SCLK MOSI RA(6) RA(5) RA(0) 7−bit Register Address D(7) Write MISO Figure 15. SPI Write 18 Submit Documentation Feedback D(6) 8−bit Register Data D(0) TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 OVERVIEW (continued) /SS SCLK MOSI RA(6) RA(5) RA(0) DON’T CARE Read 7-Bit Register Address MISO D(7) D(6) D(0) 8-Bit Register Data Figure 16. SPI Read In the SPI control mode, the TLV320AIC33 uses the pins MFP0=SSB, MFP1=SCLK, MFP2=MISO, MFP3=MOSI as a standard SPI port with clock polarity setting of 0 (typical microprocessor SPI control bit CPOL = 0). The SPI port allows full-duplex, synchronous, serial communication between a host processor (the master) and peripheral devices (slaves). The SPI master (in this case, the host processor) generates the synchronizing clock (driven onto SCLK) and initiates transmissions. The SPI slave devices (such as the TLV320AIC33) depend on a master to start and synchronize transmissions. A transmission begins when initiated by an SPI master. The byte from the SPI master begins shifting in on the slave MOSI pin under the control of the master serial clock (driven onto SCLK). As the byte shifts in on the MOSI pin, a byte shifts out on the MISO pin to the master shift register. The TLV320AIC33 interface is designed so that with a clock phase bit setting of 1 (typical microprocessor SPI control bit CPHA = 1), the master begins driving its MOSI pin and the slave begins driving its MISO pin on the first serial clock edge. The SSB pin can remain low between transmissions; however, the TLV320AIC33 only interprets the first 8 bits transmitted after the falling edge of SSB as a command byte, and the next 8 bits as a data byte only if writing to a register. Reserved register bits should be written to their default values. SPI COMMUNICATION PROTOCOL The TLV320AIC33 is entirely controlled by registers. Reading and writing these registers is accomplished by the use of an 8-bit command, which is sent to the MOSI pin of the part prior to the data for that register. The command is constructed as shown in the Command Word table. The first 7 bits specify the register address which is being written or read, from 0 to 127 (decimal). The command word ends with an R/W bit, which specifies the direction of data flow on the serial bus. In the case of a register write, the R/W bit should be set to 0. A second byte of data is sent to the MOSI pin and contains the data to be written to the register. Reading of registers is accomplished in similar fashion. The 8-bit command word sends the 7-bit register address, followed by R/W bit = 1 to signify a register read is occurring,. The 8-bit register data is then clocked out of the part on the MISO pin during the second 8 SCLK clocks in the frame. Command Word Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ADDR ADDR ADDR ADDR ADDR ADDR ADDR R/W 6 5 4 3 2 1 0 The register map of the TLV320AIC33 actually consists of multiple pages of registers, with each page containing 128 registers. The register at address zero on each page is used as a page-control register, and writing to this register determines the active page for the device. All subsequent read/write operations will access the page that is active at the time, unless a register write is performed to change the active page. Only two pages of registers are implemented in this product, with the active page defaulting to page 0 upon device reset. For example, at device reset, the active page defaults to page 0, and thus all register read/write operations for Submit Documentation Feedback 19 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 addresses 1 to 127 will access registers in page 0. If registers on page 1 must be accessed, the user must write the 8-bit sequence 0x01 to register 0, the page control register, to change the active page from page 0 to page 1. After this write, it is recommended the user also read back the page control register, to safely ensure the change in page control has occurred properly. Future read/write operations to addresses 1 to 127 will now access registers in page 1. When page 0 registers must be accessed again, the user writes the 8-bit sequence 0x00 to register 0, the page control register, to change the active page back to page 0. After a recommended read of the page control register, all further read/write operations to addresses 1 to 127 will now access page 0 registers again. Limitation on Register Writing When writing registers in SPI mode related to the audio output drivers mux, mix, gain configuration, etc., do not use the auto-increment mode. In addition, between two successive writes to these registers, the host should keep MFP0 (SPI chip select) high for at least 6.25us, to ensure that the register writes have occurred properly. CONTINUOUS READ / WRITE OPERATION The TLV320AIC33 includes the ability to read/write registers continuously, without needing to provide an address for every register accessed. In SPI mode, a continuous write is executed by transitioning MFP0 (SPI chip select) low to start the frame, sending the first 8-bit command word to read/write a particular register, and then sending multiple bytes of register data, intended for the addressed register and those following. A continuous read is done similarly, with multiple bytes read in from the addressed register and the following registers on the page. When the MFP0 (SPI chip select) pin is transitioned high again, the frame ends, as does the continuous read/write operation. A new frame must begin again with a new command word, to start the next bus transaction. Note that this continuous read/write operation does not continue past a page boundary. The user should not attempt to read/write past the end of a page, since this may result in undesirable operation. I2C CONTROL MODE The TLV320AIC33 supports the I2C control protocol when the SELECT pin is tied low, using 7-bit addressing and capable of both standard and fast modes. When in I2C control mode, the TLV320AIC33 can be configured for one of four different addresses, using the multifunction pins MFP0 and MFP1, which control the two LSBs of the device address. The 5 MSBs of the device address are fixed as 00110 and cannot be changed, while the two LSBs are given by MFP1:MFP0. This results in four possible device addresses: I2C slave device addresses for MFP1, MFP0 settings. MFP1 MFP0 Device Address 0 0 0011000 0 1 0011001 1 0 0011010 1 1 0011011 I2C is a two-wire, open-drain interface supporting multiple devices and masters on a single bus. Devices on the I2C bus only drive the bus lines LOW by connecting them to ground; they never drive the bus lines HIGH. Instead, the bus wires are pulled HIGH by pull-up resistors, so the bus wires are HIGH when no device is driving them LOW. This way, two devices cannot conflict; if two devices drive the bus simultaneously, there is no driver contention. Communication on the I2C bus always takes place between two devices, one acting as the master and the other acting as the slave. Both masters and slaves can read and write, but slaves can only do so under the direction of the master. Some I2C devices can act as masters or slaves, but the TLV320AIC33 can only act as a slave device. An I2C bus consists of two lines, SDA and SCL. SDA carries data; SCL provides the clock. All data is transmitted across the I2C bus in groups of eight bits. To send a bit on the I2C bus, the SDA line is driven to the appropriate level while SCL is LOW (a LOW on SDA indicates the bit is zero; a HIGH indicates the bit is one). Once the SDA line has settled, the SCL line is brought HIGH, then LOW. This pulse on SCL clocks the SDA bit into the receivers shift register. 20 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 The I2C bus is bidirectional: the SDA line is used both for transmitting and receiving data. When a master reads from a slave, the slave drives the data line; when a master sends to a slave, the master drives the data line. Under normal circumstances the master drives the clock line. Most of the time the bus is idle, no communication is taking place, and both lines are HIGH. When communication is taking place, the bus is active. Only master devices can start a communication. They do this by causing a START condition on the bus. Normally, the data line is only allowed to change state while the clock line is LOW. If the data line changes state while the clock line is HIGH, it is either a START condition or its counterpart, a STOP condition. A START condition is when the clock line is HIGH and the data line goes from HIGH to LOW. A STOP condition is when the clock line is HIGH and the data line goes from LOW to HIGH. After the master issues a START condition, it sends a byte that indicates which slave device it wants to communicate with. This byte is called the address byte. Each device on an I2C bus has a unique 7-bit address to which it responds. (Slaves can also have 10-bit addresses; see the I2C specification for details.) The master sends an address in the address byte, together with a bit that indicates whether it wishes to read from or write to the slave device. Every byte transmitted on the I2C bus, whether it is address or data, is acknowledged with an acknowledge bit. When a master has finished sending a byte (eight data bits) to a slave, it stops driving SDA and waits for the slave to acknowledge the byte. The slave acknowledges the byte by pulling SDA LOW. The master then sends a clock pulse to clock the acknowledge bit. Similarly, when a master has finished reading a byte, it pulls SDA LOW to acknowledge this to the slave. It then sends a clock pulse to clock the bit. A not-acknowledge is performed by simply leaving SDA HIGH during an acknowledge cycle. If a device is not present on the bus, and the master attempts to address it, it will receive a not–acknowledge because no device is present at that address to pull the line LOW. When a master has finished communicating with a slave, it may issue a STOP condition. When a STOP condition is issued, the bus becomes idle again. A master may also issue another START condition. When a START condition is issued while the bus is active, it is called a repeated START condition. The TLV320AIC33 also responds to and acknowledges a General Call, which consists of the master issuing a command with a slave address byte of 00H. SCL DA(6) SDA Start (M) DA(0) 7-bit Device Address (M) RA(7) Write (M) Slave Ack (S) RA(0) 8-bit Register Address (M) D(7) Slave Ack (S) D(0) 8-bit Register Data (M) Slave Ack (S) Stop (M) (M) => SDA Controlled by Master (S) => SDA Controlled by Slave Figure 17. I2C Write SCL DA(6) SDA Start (M) DA(0) 7-bit Device Address (M) RA(7) Write (M) Slave Ack (S) DA(6) RA(0) 8-bit Register Address (M) Slave Ack (S) Repeat Start (M) DA(0) 7-bit Device Address (M) D(7) Read (M) Slave Ack (S) 8-bit Register Data (S) D(0) Master No Ack (M) Stop (M) (M) => SDA Controlled by Master (S) => SDA Controlled by Slave Figure 18. I2C Read In the case of an I2C register write, if the master does not issue a STOP condition, then the device enters auto-increment mode. So in the next eight clocks, the data on SDA is treated as data for the next incremental register. Submit Documentation Feedback 21 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Similarly, in the case of an I2C register read, after the device has sent out the 8-bit data from the addressed register, if the master issues an ACKNOWLEDGE, the slave takes over control of SDA bus and transmit for the next 8 clocks the data of the next incremental register. DIGITAL AUDIO DATA SERIAL INTERFACE Audio data is transferred between the host processor and the TLV320AIC33 via the digital audio data serial interface, or audio bus. The audio bus on this device is very flexible, including left or right justified data options, support for I2S or PCM protocols, programmable data length options, a TDM mode for multichannel operation, very flexible master/slave configurability for each bus clock line, and the ability to communicate with multiple devices within a system directly. The data serial interface uses two sets of pins for communication between external devices, with the particular pin used controlled through register programming. This configuration is shown in Figure 19 below. WCLK GPIO1 GPIO2 BCLK DIN DOUT MFP3 Audio Serial Data Bus Figure 19. Alternate Audio Bus Mulitplexing Function In cases where MFP3 is needed for a secondary device digital input, the TLV320AIC33 must be used in I2C mode (when in SPI mode, MFP3 is used as the SPI bus MOSI pin and thus cannot be used here as an alternate digital input source). This mux capability allows the TLV320AIC33 to communicate with two separate devices with independent I2S/PCM buses. An example of such an application is a cellphone containing a Bluetooth transceiver with PCM/I2S interface, as shown in Figure 20. The applications processor can be connected to the WCLK, BCLK, DIN, DOUT pins on the TLV320AIC33, while a Bluetooth device with PCM interface can be connected to the GPIO1, GPIO2, MFP3, and DOUT pins on the TLV320AIC33. By programming the registers via I2C control, the applications processor can determine which device is communicating with the TLV320AIC33. This is attractive in cases where the TLV320AIC33 can be configured to communicate data with the Bluetooth device, then the applications processor can be put into a low power sleep mode, while voice/audio transmission still occurs between the Bluetooth device and the TLV320AIC33. 22 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 GPIO2 GPIO1 MFP3 DOUT Processor 2 DIN BCLK WCLK Processor 1 AIC33 Possible Processor Types: Application Processor, Multimedia Processor, Compressed Audio Decoder, Wireless Modem, Bluetooth Module, Additional Audio/Voice Codec Figure 20. AIC33 Connected to Multiple Audio Devices The audio bus of the TLV320AIC33 can be configured for left or right justified, I2S, DSP, or TDM modes of operation, where communication with standard telephony PCM interfaces is supported within the TDM mode. These modes are all MSB-first, with data width programmable as 16, 20, 24, or 32 bits. In addition, the word clock (WCLK or GPIO1) and bit clock (BCLK or GPIO2) can be independently configured in either Master or Slave mode, for flexible connectivity to a wide variety of processors The word clock (WCLK or GPIO1) is used to define the beginning of a frame, and may be programmed as either a pulse or a square-wave signal. The frequency of this clock corresponds to the maximum of the selected ADC and DAC sampling frequencies. The bit clock (BCLK or GPIO2) is used to clock in and out the digital audio data across the serial bus. When in Master mode, this signal can be programmed in two further modes: continuous transfer mode, and 256-clock mode. In continuous transfer mode, only the minimal number of bit clocks needed to transfer the audio data are generated, so in general the number of bit clocks per frame will be two times the data width. For example, if data width is chosen as 16-bits, then 32 bit clocks will be generated per frame. If the bit clock signal in master mode will be used by a PLL in another device, it is recommended that the 16-bit or 32-bit data width selections be used. These cases result in a low jitter bit clock signal being generated, having frequencies of 32×Fs or 64×Fs. In the cases of 20-bit and 24-bt data width in master mode, the bit clocks generated in each frame will not all be of equal period, due to the device not having a clean 40×Fs or 48×Fs clock signal readily available. The average frequency of the bit clock signal is still accurate in these cases (being 40×Fs or 48×Fs), but the resulting clock signal has higher jitter than in the 16-bit and 32-bit cases. In 256-clock mode, a constant 256 bit clocks per frame are generated, independent of the data width chosen. The TLV320AIC33 further includes programmability to tri-state the DOUT line during all bit clocks when valid data is not being sent. By combining this capability with the ability to program at what bit clock in a frame the audio data will begin, time-division multiplexing (TDM) can be accomplished, resulting in multiple codecs able to use a single audio serial data bus. When the audio serial data bus is powered down while configured in master mode, the pins associated with the interface will be put into a tri-state output condition. RIGHT JUSTIFIED MODE In right-justified mode, the LSB of the left channel is valid on the rising edge of the bit clock preceding the falling edge of word clock. Similarly, the LSB of the right channel is valid on the rising edge of the bit clock preceding the rising edge of the word clock. Submit Documentation Feedback 23 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 1/fs WCLK BCLK Left Channel SDIN/ SDOUT 0 n−1 n−2 n−3 MSB Right Channel 2 1 0 n−1 n−2 n−3 2 1 0 LSB Figure 21. Right Justified Serial Bus Mode Operation LEFT JUSTIFIED MODE In left-justified mode, the MSB of the right channel is valid on the rising edge of the bit clock following the falling edge of the word clock. Similarly the MSB of the left channel is valid on the rising edge of the bit clock following the rising edge of the word clock. n-1 n-2 n-3 n-1 n-2 n-3 Figure 22. Left Justified Serial Data Bus Mode Operation I2S MODE In I2S mode, the MSB of the left channel is valid on the second rising edge of the bit clock after the falling edge of the word clock. Similarly the MSB of the right channel is valid on the second rising edge of the bit clock after the rising edge of the word clock. n-1 n-2 n-3 n-1 n-2 n-3 Figure 23. I2S Serial Data Bus Mode Operation 24 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 DSP MODE In DSP mode, the rising edge of the word clock starts the data transfer with the left channel data first and immediately followed by the right channel data. Each data bit is valid on the falling edge of the bit clock. 1/fs WCLK BCLK Left Channel SDIN/ SDOUT n−1 n−2 n−3 n−4 LSB MSB 2 Right Channel 1 0 n−1 n−2 n−3 2 LSB MSB 1 0 LSB MSB Figure 24. DSP Serial Bus Mode Operation TDM DATA TRANSFER Time-division multiplexed data transfer can be realized in any of the above transfer modes if the 256-clock bit clock mode is selected, although it is recommended to be used in either left-justified mode or DSP mode. By changing the programmable offset, the bit clock in each frame where the data begins can be changed, and the serial data output driver (DOUT) can also be programmed to tri-state during all bit clocks except when valid data is being put onto the bus. This allows other codecs to be programmed with different offsets and to drive their data onto the same DOUT line, just in a different slot. For incoming data, the codec simply ignores data on the bus except where it is expected based on the programmed offset. Note that the location of the data when an offset is programmed is different, depending on what transfer mode is selected. In DSP mode, both left and right channels of data are transferred immediately adjacent to each other in the frame. This differs from left-justified mode, where the left and right channel data will always be a half-frame apart in each frame. In this case, as the offset is programmed from zero to some higher value, both the left and right channel data move across the frame, but still stay a full half-frame apart from each other. This is depicted in Figure 25 for the two cases. Submit Documentation Feedback 25 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 DSP Mode word clock bit clock data in/out N-1 N-2 1 Left Channel Data offset 0 N-1 N-2 1 0 Right Channel Data Left Justified Mode word clock bit clock data in/out N-1 offset N-2 1 Left Channel Data 0 N-1 offset N-2 1 0 Right Channel Data Figure 25. DSP Mode and Left Justified Modes, Showing the Effect of a Programmed Data Word Offset AUDIO DATA CONVERTERS The TLV320AIC33 supports the following standard audio sampling rates: 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, and 96 kHz. The converters can also operate at different sampling rates in various combinations, which are described further below. The data converters are based on the concept of an Fsref rate that is used internal to the part, and it is related to the actual sampling rates of the converters through a series of ratios. For typical sampling rates, Fsref will be either 44.1 kHz or 48 kHz, although it can realistically be set over a wider range of rates up to 53 kHz, with additional restrictions applying if the PLL is used. This concept is used to set the sampling rates of the ADC and DAC, and also to enable high quality playback of low sampling rate data, without high frequency audible noise being generated. The sampling rate of the ADC and DAC can be set to Fsref/NDAC or 2×Fsref/NDAC, with NDAC being 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, or 6. While only one Fsref can be used at a time in the part, the ADC and DAC sampling rates can differ from each other by using different NADC and NDAC divider ratios for each. For example, with Fsref=44.1-kHz, the DAC sampling rate can be set to 44.1-kHz by using NDAC=1, while the ADC sampling rate can be set to 8.018-kHz by using NADC=5.5. When the ADCs and DACs are operating at different sampling rates, an additional word clock is required, to provide information regarding where data begins for the ADC versus the DAC. In this case, the standard bit clock signal (which can be supplied through the BCLK pin or through GPIO2) is used to transfer both ADC and DAC data, the standard word clock signal is used to identify the start of the DAC data, and a separate ADC word clock signal (denoted ADWK) is used. This clock can be supplied or generated from GPIO1 at the same time the DAC word clock is supplied or generated from WCLK. AUDIO CLOCK GENERATION The audio converters in the TLV320AIC33 need an internal audio master clock at a frequency of 256×Fsref, which can be obtained in a variety of manners from an external clock signal applied to the device. A more detailed diagram of the audio clock section of the TLV320AIC33 is shown in Figure 26. 26 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 MCLK BCLK GPIO2 PLL_CLKIN CLKDIV_CLKIN CLKDIV_IN PLL_IN Q = 3,3, . . . . ,16,17 K = J.D J = 1,2,3,. . . , 62,63 D= 0000,0001, . . . ,9998,9999 R= 1,2,3,4, . . . ,15,16 P= 1,2, . . . . ,7,8 K*R/P 2/Q CLKDIV_OUT PLL_OUT 1/8 PLLDIV_OUT CODEC_CLKIN CLKMUX_OUT CODEC_CLK=256*Fsref CLKOUT_IN M =1,2,4,8 N = 2,3, . . . ., 16,17 2/(N*M) CODEC CLKOUT GPIO1 DAC_FS WCLK= Fsref/ Ndac Ndac=1,1.5,2, . . ., 5.5,6 DAC DRA => Ndac = 0.5 ADC_FS GPIO1= Fsref/ Nadc Ndac=1,1.5,2, . . ., 5.5,6 ADC DRA => Nadc = 0.5 Figure 26. Audio Clock Generation Processing The part can accept an MCLK input from 512 kHz to 50 MHz, which can then be passed through either a programmable divider or a PLL, to get the proper internal audio master clock needed by the part. The BCLK or GPIO2 inputs can also be used to generate the internal audio master clock. This design also allows the PLL to be used for an entirely separate purpose in a system, if the audio codec is not powered up. The user can supply a separate clock to GPIO2, route this through the PLL, with the resulting output clock driven out GPIO1, for use by other devices in the system A primary concern is proper operation of the codec at various sample rates with the limited MCLK frequencies available in the system. This device includes a highly programmable PLL to accommodate such situations easily. The integrated PLL can generate audio clocks from a wide variety of possible MCLK inputs, with particular focus paid to the standard MCLK rates already widely used. When the PLL is disabled, Fsref = CLKDIV_IN / (128 × Q) Where Q = 2, 3, …, 17 CLKDIV_IN can be MCLK, BCLK, or GPIO2, selected by register 102, bits D7-D6. NOTE – when NDAC = 1.5, 2.5, 3.5, 4.5, or 5.5, odd values of Q are not allowed. In this mode, MCLK can be as high as 50 MHz, and Fsref should fall within 39 kHz to 53 kHz. When the PLL is enabled, Submit Documentation Feedback 27 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Fsref = (PLLCLK_IN × K × R) / (2048 × P), where P = 1, 2, 3,…, 8 R = 1, 2, …, 16 K = J.D J = 1, 2, 3, …, 63 D = 0000, 0001, 0002, 0003, …, 9998, 9999 PLLCLK_IN can be MCLK or BCLK, selected by Page 0, register 102, bits D5-D4 P, R, J, and D are register programmable. J is the integer portion of K (the numbers to the left of the decimal point), while D is the fractional portion of K (the numbers to the right of the decimal point, assuming four digits of precision). Examples: If If If If K K K K = 8.5, then J = 8, D = 5000 = 7.12, then J = 7, D = 1200 = 14.03, then J = 14, D = 0300 = 6.0004, then J = 6, D = 0004 When the PLL is enabled and D = 0000, the following conditions must be satisfied to meet specified performance: 2 MHz ≤ ( PLLCLK_IN / P ) ≤ 20 MHz 80 MHz ≤ (PLLCLK _IN × K × R / P ) ≤ 110 MHz 4 ≤ J ≤ 55 When the PLL is enabled and D≠0000, the following conditions must be satisfied to meet specified performance: 10 MHz ≤ PLLCLK _IN / P ≤ 20 MHz 80 MHz ≤ PLLCLK _IN × K × R / P ≤ 110 MHz 4 ≤ J ≤ 11 R=1 Example: MCLK = 12 MHz and Fsref = 44.1 kHz Select P = 1, R = 1, K = 7.5264, which results in J = 7, D = 5264 Example: MCLK = 12 MHz and Fsref = 48.0 kHz Select P = 1, R = 1, K = 8.192, which results in J = 8, D = 1920 28 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 The table below lists several example cases of typical MCLK rates and how to program the PLL to achieve Fsref = 44.1 kHz or 48 kHz. Fsref = 44.1 kHz MCLK (MHz) P R J D ACHIEVED FSREF % ERROR 2.8224 1 1 32 0 44100.00 0.0000 5.6448 1 1 16 0 44100.00 0.0000 12.0 1 1 7 5264 44100.00 0.0000 13.0 1 1 6 9474 44099.71 0.0007 16.0 1 1 5 6448 44100.00 0.0000 19.2 1 1 4 7040 44100.00 0.0000 19.68 1 1 4 5893 44100.30 –0.0007 48.0 4 1 7 5264 44100.00 0.0000 MCLK (MHz) P R J D ACHIEVED FSREF % ERROR 2.048 1 1 48 0 48000.00 0.0000 3.072 1 1 32 0 48000.00 0.0000 4.096 1 1 24 0 48000.00 0.0000 6.144 1 1 16 0 48000.00 0.0000 8.192 1 1 12 0 48000.00 0.0000 12.0 1 1 8 1920 48000.00 0.0000 13.0 1 1 7 5618 47999.71 0.0006 16.0 1 1 6 1440 48000.00 0.0000 19.2 1 1 5 1200 48000.00 0.0000 19.68 1 1 4 9951 47999.79 0.0004 48.0 4 1 8 1920 48000.00 0.0000 Fsref = 48 kHz The AIC33 can also output a separate clock on the GPIO1 pin. If the PLL is being used for the audio data converter clock, the M and N settings can be used to provide a divided version of the PLL output. If the PLL is not being used for the audio data converter clock, the PLL can still be enabled to provide a completely independent clock output on GPIO1. The formula for the GPIO1 clock output when PLL is enabled and CLKMUX_OUT is 0 is: GPIO1 = (PLLCLK_IN× 2 × K × R) / (M × N × P) When CLKMUX_OUT is 1, regardless of whether PLL is enabled or disabled, the input to the clock output divider can be selected as MCLK, BCLK, or GPIO2. Is this case, the formula for the GPIO1 clock is: GPIO1 = (CLKDIV_IN × 2) / (M × N), where M = 1, 2, 4, 8 N = 2, 3, …, 17 CLKDIV_IN can be BCLK, MCLK, or GPIO2, selected by page 0, register 102, bits D7-D6 STEREO AUDIO ADC The TLV320AIC33 includes a stereo audio ADC, which uses a delta-sigma modulator with 128-times oversampling in single-rate mode, followed by a digital decimation filter. The ADC supports sampling rates from 8 kHz to 48 kHz in single-rate mode, and up to 96 kHz in dual-rate mode. Whenever the ADC or DAC is in operation, the device requires an audio master clock be provided and appropriate audio clock generation be setup within the part. In order to provide optimal system power dissipation, the stereo ADC can be powered one channel at a time, to support the case where only mono record capability is required. In addition, both channels can be fully powered or entirely powered down. Submit Documentation Feedback 29 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 The integrated digital decimation filter removes high-frequency content and downsamples the audio data from an initial sampling rate of 128 Fs to the final output sampling rate of Fs. The decimation filter provides a linear phase output response with a group delay of 17/Fs. The –3 dB bandwidth of the decimation filter extends to 0.45 Fs and scales with the sample rate (Fs). The filter has minimum 75dB attenuation over the stopband from 0.55 Fs to 64 Fs. Independent digital highpass filters are also included with each ADC channel, with a corner frequency that can be independently set to three different settings or can be disabled entirely. Because of the oversampling nature of the audio ADC and the integrated digital decimation filtering, requirements for analog anti-aliasing filtering are very relaxed. The TLV320AIC33 integrates a second order analog anti-aliasing filter with 20-dB attenuation at 1 MHz. This filter, combined with the digital decimation filter, provides sufficient anti-aliasing filtering without requiring additional external components. The ADC is preceded by a programmable gain amplifier (PGA), which allows analog gain control from 0 dB to 59.5 dB in steps of 0.5 dB. The PGA gain changes are implemented with an internal soft-stepping algorithm that only changes the actual volume level by one 0.5-dB step every one or two ADC output samples, depending on the register programming (see registers Page-0/Reg-19 and 22). This soft-stepping ensures that volume control changes occur smoothly with no audible artifacts. On reset, the PGA gain defaults to a mute condition, and upon power down, the PGA soft-steps the volume to mute before shutting down. A read-only flag is set whenever the gain applied by PGA equals the desired value set by the register. The soft-stepping control can also be disabled by programming a register bit. When soft stepping is enabled, the audio master clock must be applied to the part after the ADC power down register is written to ensure the soft-stepping to mute has completed. When the ADC powerdown flag is no longer set, the audio master clock can be shut down. AUTOMATIC GAIN CONTROL (AGC) An automatic gain control (AGC) circuit is included with the ADC and can be used to maintain nominally constant output signal amplitude when recording speech signals (it can be fully disabled if not desired). This circuitry automatically adjusts the PGA gain as the input signal becomes overly loud or very weak, such as when a person speaking into a microphone moves closer or farther from the microphone. The AGC algorithm has several programmable settings, including target gain, attack and decay time constants, noise threshold, and maximum PGA gain applicable that allow the algorithm to be fine tuned for any particular application. The algorithm uses the absolute average of the signal (which is the average of the absolute value of the signal) as a measure of the nominal amplitude of the output signal. Note that completely independent AGC circuitry is included with each ADC channel with entirely independent control over the algorithm from one channel to the next. This is attractive in cases where two microphones are used in a system, but may have different placement in the end equipment and require different dynamic performance for optimal system operation. Target gain represents the nominal output level at which the AGC attempts to hold the ADC output signal level. The TLV320AIC33 allows programming of eight different target gains, which can be programmed from –5.5 dB to –24 dB relative to a full-scale signal. Since the device reacts to the signal absolute average and not to peak levels, it is recommended that the larger gain be set with enough margin to avoid clipping at the occurrence of loud sounds. Attack time determines how quickly the AGC circuitry reduces the PGA gain when the input signal is too loud. It can be varied from 8 ms to 20 ms. Decay time determines how quickly the PGA gain is increased when the input signal is too low. It can be varied in the range from 100 ms to 500 ms. Noise gate threshold determines the level below which if the input speech average value falls, AGC considers it as a silence and hence brings down the gain to 0 dB in steps of 0.5 dB every FS and sets the noise threshold flag. The gain stays at 0 dB unless the input speech signal average rises above the noise threshold setting. This ensures that noise does not get gained up in the absence of speech. Noise threshold level in the AGC algorithm is programmable from –30 dB to –90 dB relative to full scale. A disable noise gate feature is also available. This operation includes programmable debounce and hysteresis functionality to avoid the AGC gain from cycling between high gain and 0 dB when signals are near the noise threshold level. When the noise threshold flag is set, the status of gain applied by the AGC and the saturation flag should be ignored. Maximum PGA gain applicable allows the user to restrict the maximum PGA gain that can be applied by the AGC algorithm. This can be used for limiting PGA gain in situations where environmental noise is greater than programmed noise threshold. It can be programmed from 0 dB to +59.5 dB in steps of 0.5 dB. 30 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Input Signal Output Signal AGC Gain Decay Time Attack Time Figure 27. Typical Operation of the AGC Algorithm During Speech Recording Note that the time constants here are correct when the ADC is not in double-rate audio mode. The time constants are achieved using the Fsref value programmed in the control registers. However, if the Fsref is set in the registers to, for example, 48 kHz, but the actual audio clock or PLL programming actually results in a different Fsref in practice, then the time constants would not be correct. STEREO AUDIO DAC The TLV320AIC33 includes a stereo audio DAC supporting sampling rates from 8 kHz to 96 kHz. Each channel of the stereo audio DAC consists of a digital audio processing block, a digital interpolation filter, multi-bit digital delta-sigma modulator, and an analog reconstruction filter. The DAC is designed to provide enhanced performance at low sampling rates through increased oversampling and image filtering, thereby keeping quantization noise generated within the delta-sigma modulator and signal images strongly suppressed within the audio band to beyond 20 kHz. This is realized by keeping the upsampled rate constant at 128 × Fsref and changing the oversampling ratio as the input sample rate is changed. For an Fsref of 48 kHz, the digital delta-sigma modulator always operates at a rate of 6.144 MHz. This ensures that quantization noise generated within the delta-sigma modulator stays low within the frequency band below 20 kHz at all sample rates. Similarly, for an Fsref rate of 44.1 kHz, the digital delta-sigma modulator always operates at a rate of 5.6448 MHz. The following restrictions apply in the case when the PLL is powered down and double-rate audio mode is enabled in the DAC. Allowed Q values = 4, 8, 9, 12, 16 Q values where equivalent Fsref can be achieved by turning on PLL Q = 5, 6, 7 (set P = 5 / 6 / 7 and K = 16.0 and PLL enabled) Q = 10, 14 (set P = 5, 7 and K = 8.0 and PLL enabled) DIGITAL AUDIO PROCESSING The DAC channel consists of optional filters for de-emphasis and bass, treble, midrange level adjustment, speaker equalization, and 3-D effects processing. The de-emphasis function is implemented by a programmable digital filter block with fully programmable coefficients (see Page-1/Reg-21-26 for left channel, Page-1/Reg-47-52 for right channel). If de-emphasis is not required in a particular application, this programmable filter block can be used for some other purpose. The de-emphasis filter transfer function is given by: Submit Documentation Feedback 31 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 H(z) + N0 ) N1 z *1 32768 * D1 z *1 (1) where the N0, N1, and D1 coefficients are fully programmable individually for each channel. The coefficients that should be loaded to implement standard de-emphasis filters are given in Table 1. Table 1. De-Emphasis Coefficients for Common Audio Sampling Rates (1) SAMPLING FREQUENCY N0 N1 D1 32-kHz 16950 –1220 17037 44.1-kHz 15091 –2877 20555 48-kHz (1) 14677 –3283 21374 Default de-emphasis coefficients. In addition to the de-emphasis filter block, the DAC digital effects processing includes a fourth order digital IIR filter with programmable coefficients (one set per channel). This filter is implemented as cascade of two biquad sections with frequency response given by: N0 ) 2 ǒ32768 *2 N1 z *1 ) N2 z *2 D1 z *1 * D2 z *2 N3 ) 2 Ǔǒ32768 *2 N4 z *1 ) N5 z*2 D4 z *1 * D5 z*2 Ǔ (2) The N and D coefficients are fully programmable, and the entire filter can be enabled or bypassed. The structure of the filtering when configured for independent channel processing is shown below in Figure 28, with LB1 corresponding to the first left-channel biquad filter using coefficients N0, N1, N2, D1, and D2. LB2 similarly corresponds to the second left-channel biquad filter using coefficients N3, N4, N5, D4, and D5. The RB1 and RB2 filters refer to the first and second right-channel biquad filters, respectively. LB1 LB2 RB1 RB2 Figure 28. Structure of the Digital Effects Processing for Independent Channel Processing The coefficients for this filter implement a variety of sound effects, with bass-boost or treble boost being the most commonly used in portable audio applications. The default N and D coefficients in the part are given in Table 2 and implement a shelving filter with 0-dB gain from DC to approximately 150 Hz, at which point it rolls off to a 3-dB attenuation for higher frequency signals, thus giving a 3-dB boost to signals below 150 Hz. The N and D coefficients are represented by 16-bit two’s complement numbers with values ranging from –32768 to 32767. 32 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Table 2. Default Digital Effects Processing Filter Coefficients, When in Independent Channel Processing Configuration Coefficients N0 = N3 N1 = N4 N2 = N5 D1 = D4 D2 = D5 27619 -27034 26461 32131 -31506 The digital processing also includes capability to implement 3-D processing algorithms by providing means to process the mono mix of the stereo input, and then combine this with the individual channel signals for stereo output playback. The architecture of this processing mode, and the programmable filters available for use in the system, is shown in Figure 29. Note that the programmable attenuation block provides a method of adjusting the level of 3-D effect introduced into the final stereo output. This combined with the fully programmable biquad filters in the system enables the user to fully optimize the audio effects for a particular system and provide extensive differentiation from other systems using the same device. L LB2 TOLEFTCHANNEL LB1 Atten RB2 R TO RIGHT CHANNEL Figure 29. Architecture of the Digital Audio Processing When 3-D Effects are Enabled It is recommended that the digital effects filters should be disabled while the filter coefficients are being modified. While new coefficients are being written to the device over the control port, it is possible that a filter using partially updated coefficients may actually implement an unstable system and lead to oscillation or objectionable audio output. By disabling the filters, changing the coefficients, and then re-enabling the filters, these types of effects can be entirely avoided. DIGITAL INTERPOLATION FILTER The digital interpolation filter upsamples the output of the digital audio processing block by the required oversampling ratio before data is provided to the digital delta-sigma modulator and analog reconstruction filter stages. The filter provides a linear phase output with a group delay of 21/Fs. In addition, programmable digital interpolation filtering is included to provide enhanced image filtering and reduce signal images caused by the upsampling process that are below 20 kHz. For example, upsampling an 8-kHz signal produces signal images at multiples of 8-kHz (i.e., 8 kHz, 16 kHz, 24 kHz, etc.). The images at 8 kHz and 16 kHz are below 20 kHz and still audible to the listener; therefore, they must be filtered heavily to maintain a good quality output. The interpolation filter is designed to maintain at least 65-dB rejection of images that land below 7.455 Fs. In order to utilize the programmable interpolation capability, the Fsref should be programmed to a higher rate (restricted to be in the range of 39 kHz to 53 kHz when the PLL is in use), and the actual Fs is set using the NDAC divider. For example, if Fs = 8 kHz is required, then Fsref can be set to 48 kHz, and the DAC Fs set to Fsref/6. This ensures that all images of the 8-kHz data are sufficiently attenuated well beyond a 20-kHz audible frequency range. Submit Documentation Feedback 33 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 DELTA-SIGMA AUDIO DAC The stereo audio DAC incorporates a third order multi-bit delta-sigma modulator followed by an analog reconstruction filter. The DAC provides high-resolution, low-noise performance, using oversampling and noise shaping techniques. The analog reconstruction filter design consists of a 6-tap analog FIR filter followed by a continuous time RC filter. The analog FIR operates at a rate of 128 × Fsref (6.144 MHz when Fsref = 48 kHz, 5.6448 MHz when Fsref = 44.1 kHz). Note that the DAC analog performance may be degraded by excessive clock jitter on the MCLK input. Therefore, care must be taken to keep jitter on this clock to a minimum. AUDIO DAC DIGITAL VOLUME CONTROL The audio DAC includes a digital volume control block which implements a programmable digital gain. The volume level can be varied from 0 dB to –63.5 dB in 0.5-dB steps, in addition to a mute bit, independently for each channel. The volume level of both channels can also be changed simultaneously by the master volume control. Gain changes are implemented with a soft-stepping algorithm, which only changes the actual volume by one step per input sample, either up or down, until the desired volume is reached. The rate of soft-stepping can be slowed to one step per two input samples through a register bit. Because of soft-stepping, the host does not know when the DAC has been actually muted. This may be important if the host wishes to mute the DAC before making a significant change, such as changing sample rates. In order to help with this situation, the device provides a flag back to the host via a read-only register bit that alerts the host when the part has completed the soft-stepping and the actual volume has reached the desired volume level. The soft-stepping feature can be disabled through register programming. If soft-stepping is enabled, the MCLK signal should be kept applied to the device until the DAC power-down flag is set. When this flag is set, the internal soft-stepping process and power down sequence is complete, and the MCLK can then be stopped if desired. The TLV320AIC33 also includes functionality to detect when the user switches on or off the de-emphasis or digital audio processing functions, to first (1) soft-mute the DAC volume control, (2) change the operation of the digital effects processing, and (3) soft-unmute the part. This avoids any possible pop/clicks in the audio output due to instantaneous changes in the filtering. A similar algorithm is used when first powering up or down the DAC. The circuit begins operation at power up with the volume control muted, then soft-steps it up to the desired volume level. At power down, the logic first soft-steps the volume down to a mute level, then powers down the circuitry. ANALOG OUTPUT COMMON-MODE ADJUSTMENT The output common-mode voltage and output range of the analog output are determined by an internal bandgap reference, in contrast to other codecs that may use a divided version of the supply. This scheme is used to reduce the coupling of noise that may be on the supply (such as 217-Hz noise in a GSM cellphone) into the audio signal path. However, due to the possible wide variation in analog supply range (2.7 V – 3.6 V), an output common-mode voltage setting of 1.35 V, which would be used for a 2.7 V supply case, will be overly conservative if the supply is actually much larger, such as 3.3 V or 3.6 V. In order to optimize device operation, the TLV320AIC33 includes a programmable output common-mode level, which can be set by register programming to a level most appropriate to the actual supply range used by a particular customer. The output common-mode level can be varied among four different values, ranging from 1.35 V (most appropriate for low supply ranges, near 2.7 V) to 1.8 V (most appropriate for high supply ranges, near 3.6 V). Note that there is also some limitation on the range of DVDD voltage as well in determining which setting is most appropriate. Table 3. Appropriate Settings 34 CM SETTING RECOMMENDED AVDD, DRVDD RECOMMENDED DVDD 1.35 2.7 V – 3.6 V 1.525 V – 1.95 V 1.50 3.0 V – 3.6 V 1.65 V – 1.95 V 1.65 V 3.3 V – 3.6 V 1.8 V – 1.95 V 1.8 V 3.6 V 1.95 V Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 AUDIO DAC POWER CONTROL The stereo DAC can be fully powered up or down, and in addition, the analog circuitry in each DAC channel can be powered up or down independently. This provides power savings when only a mono playback stream is needed. AUDIO ANALOG INPUTS The TLV320AIC33 includes ten analog audio input pins, which can be configured as up to four fully-differential pair plus one single-ended pair of audio inputs, or up to six single-ended audio inputs. . These pins connect through series resistors and switches to the virtual ground terminals of two fully differential opamps (one per ADC/PGA channel). By selecting to turn on only one set of switches per opamp at a time, the inputs can be effectively muxed to each ADC PGA channel. By selecting to turn on multiple sets of switches per opamp at a time, mixing can also be achieved. Mixing of multiple inputs can easily lead to PGA outputs that exceed the range of the internal opamps, resulting in saturation and clipping of the mixed output signal. Whenever mixing is being implemented, the user should take adequate precautions to avoid such a saturation case from occurring. In general, the mixed signal should not exceed 2 Vpp (single-ended) or 4 Vpp (differential). In most mixing applications, there is also a general need to adjust the levels of the individual signals being mixed. For example, if a soft signal and a large signal are to be mixed and played together, the soft signal generally should be amplified to a level comparable to the large signal before mixing. In order to accommodate this need, the TLV320AIC33 includes input level control on each of the individual inputs before they are mixed or muxed into the ADC PGAs, with gain programmable from 0 dB to –12 dB in 1.5 dB steps. Note that this input level control is not intended to be a volume control, but instead used occasionally for level setting. Soft-stepping of the input level control settings is implemented in this device, with the speed and functionality following the settings used by the ADC PGA for soft-stepping. The TLV320AIC33 supports the ability to mix up to three fully-differential analog inputs into each ADC PGA channel. Figure 30 shows the mixing configuration for the left channel, which can mix the signals LINE1LP-LINE1LM, LINE2LP-LINE2LM, and LINE1RP-LINE1RM GAIN=0,−1.5,−3,..,−12dB,MUTE LINE1LP LINE1LM GAIN=0,−1.5,−3,..,−12dB, MUTE LINE2LP TO LEFT ADC LINE2LM PGA GAIN=0,−1.5,−3,..,−12dB,MUTE LINE1RP LINE1RM Figure 30. Left Channel Fully-Differential Analog Input Mixing Configuration Three fully-differential analog inputs can similarly be mixed into the right ADC PGA as well, consisting of LINE1RP-LINE1RM, LINE2RP-LINE2RM, and LINE1LP-LINE1LM. Note that it is not necessary to mix all three fully-differential signals if this is not desired – unnecessary inputs can simply be muted using the input level control registers. Inputs can also be selected as single-ended instead of fully-differential, and mixing or muxing into the ADC Submit Documentation Feedback 35 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 PGAs is also possible in this mode. It is not possible, however, for an input pair to be selected as fully-differential for connection to one ADC PGA and simultaneously selected as single-ended for connection to the other ADC PGA channel. However, it is possible for an input to be selected or mixed into both left and right channel PGAs, as long as it has the same configuration for both channels (either both single-ended or both fully-differential). Figure 31 shows the single-ended mixing configuration for the left channel ADC PGA, which enables mixing of the signals LINE1LP, LINE2LP, LINE1RP, MIC3L, and MIC3R. The right channel ADC PGA mix is similar, enabling mixing of the signals LINE1RP, LINE2RP, LINE1LP, MIC3L, and MIC3R. GAIN=0,-1.5,-3,..,-12dB,MUTE LINE1LP/MIC1L GAIN=0,-1.5,-3,..,-12dB,MUTE LINE2L/MIC2LP GAIN=0,-1.5,-3,..,-12dB,MUTE TO LEFT ADC PGA LINE1R/MIC1RP GAIN=0,-1.5,-3,..,-12dB,MUTE LINE3L/MIC3L GAIN=0,-1.5,-3,..,-12dB,MUTE LINE3R/MIC3R Figure 31. Left Channel Single-Ended Analog Input Mixing Configuration ANALOG INPUT BYPASS PATH FUNCTIONALITY The TLV320AIC33 includes the additional ability to route some analog input signals past the integrated data converters, for mixing with other analog signals and then direction connection to the output drivers. This capability is useful in a cellphone, for example, when a separate FM radio device provides a stereo analog output signal that needs to be routed to headphones. The TLV320AIC33 supports this in a low power mode by providing a direct analog path through the device to the output drivers, while all ADCs and DACs can be completely powered down to save power. For fully-differential inputs, the TLV320AIC33 provides the ability to pass the signals LINE2LP-LINE2LM and LINE2RP-LINE2RM to the output stage directly. If in single-ended configuration, the device can pass the signal LINE2LP and LINE2RP to the output stage directly. ADC PGA SIGNAL BYPASS PATH FUNCTIONALITY In addition to the input bypass path described above, the TLV320AIC33 also includes the ability to route the ADC PGA output signals past the ADC, for mixing with other analog signals and then direction connection to the output drivers. These bypass functions are described in more detail in the sections on output mixing and output driver configurations. 36 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 INPUT IMPEDANCE AND VCM CONTROL The TLV320AIC33 includes several programmable settings to control analog input pins, particularly when they are not selected for connection to an ADC PGA. The default option allows unselected inputs to be put into a tri-state condition, such that the input impedance seen looking into the device is extremely high. Note, however, that the pins on the device do include protection diode circuits connected to AVDD and AVSS. Thus, if any voltage is driven onto a pin approximately one diode drop (~0.6 V) above AVDD or one diode drop below AVSS, these protection diodes will begin conducting current, resulting in an effective impedance that no longer appears as a tri-state condition. Another programmable option for unselected analog inputs is to weakly hold them at the common-mode input voltage of the ADC PGA (which is determined by an internal bandgap voltage reference). This is useful to keep the ac-coupling capacitors connected to analog inputs biased up at a normal DC level, thus avoiding the need for them to charge up suddenly when the input is changed from being unselected to selected for connection to an ADC PGA. This option is controlled in Page-0/Reg-20 and 23. The user should ensure this option is disabled when an input is selected for connection to an ADC PGA or selected for the analog input bypass path, since it can corrupt the recorded input signal if left operational when an input is selected. In most cases, the analog input pins on the TLV320AIC33 should be ac-coupled to analog input sources, the only exception to this generally being if an ADC is being used for DC voltage measurement. The ac-coupling capacitor will cause a highpass filter pole to be inserted into the analog signal path, so the size of the capacitor must be chosen to move that filter pole sufficiently low in frequency to cause minimal effect on the processed analog signal. The input impedance of the analog inputs when selected for connection to an ADC PGA varies with the setting of the input level control, starting at approximately 20 kΩ with an input level control setting of 0-dB, and increasing to approximately 80-kΩ when the input level control is set at –12 dB. For example, using a 0.1 µF ac-coupling capacitor at an analog input will result in a highpass filter pole of 80 Hz when the 0 dB input level control setting is selected. MICBIAS GENERATION The TLV320AIC33 includes a programmable microphone bias output voltage (MICBIAS), capable of providing output voltages of 2.0 V or 2.5 V (both derived from the on-chip bandgap voltage) with 4-mA output current drive. In addition, the MICBIAS may be programmed to be switched to AVDD directly through an on-chip switch, or it can be powered down completely when not needed, for power savings. This function is controlled by register programming in Page-0/Reg-25. DIGITAL MICROPHONE CONNECTIVITY The TLV320AIC33 includes support for connection of a digital microphone to the device by routing the digital signal directly into the ADC digital decimation filter, where it is filtered, downsampled, and provided to the host processor over the audio data serial bus. When digital microphone mode is enabled, the TLV320AIC33 provides an oversampling clock output for use by the digital microphone to transmit its data. The TLV320AIC33 includes the capability to latch the data on either the rising, falling, or both edges of this supplied clock, enabling support for stereo digital microphones. In this mode, the oversampling ratio of the digital mic modulator can be programmed as 128, 64 or 32 times the ADC sample rate, ADCFS. The GPIO1 pin will output the serial oversampling clock at the programmed rate. TLV320AIC33 latches the data input on GPIO2 as the Left and Right channel digital microphone data. For the Left channel input, GPIO2 will be sampled on the rising edge of the clock, and for the Right channel input, GPIO2 will be sampled on the falling edge of the clock. If a single digital mic channel is needed then the corresponding ADC channel should be powered up, and the unused channel should be powered down. When digital microphone mode is enabled, neither ADC can be used for digitizing analog inputs. ANALOG FULLY DIFFERENTIAL LINE OUTPUT DRIVERS The TLV320AIC33 has two fully differential line output drivers, each capable of driving a 10-kΩ differential load. The output stage design leading to the fully differential line output drivers is shown in Figure 32 and Figure 33. This design includes extensive capability to adjust signal levels independently before any mixing occurs, beyond that already provided by the PGA gain and the DAC digital volume control. The LINE2L/R signals refer to the signals that travel through the analog input bypass path to the output stage. Submit Documentation Feedback 37 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 The PGA_L/R signals refer to the outputs of the ADC PGA stages that are similarly passed around the ADC to the output stage. Note that since both left and right channel signals are routed to all output drivers, a mono mix of any of the stereo signals can easily be obtained by setting the volume controls of both left and right channel signals to –6 dB and mixing them. Undesired signals can also be disconnected from the mix as well through register control. DAC_L1 DAC_L STEREO AUDIO DAC DAC_L2 DAC_L3 DAC_R DAC_R1 DAC_R2 DAC_R3 LINE2L LINE2R PGA_L PGA_R DAC_L1 DAC_R1 VOLUME CONTROLS, MIXING LEFT_LOP LEFT_LOM Gain = 0dB to +9dB, Mute DAC_L3 LINE2L LINE2R PGA_L PGA_R DAC_L1 DAC_R1 VOLUME CONTROLS, MIXING RIGHT_LOP RIGHT_LOM Gain = 0dB to +9 dB, Mute DAC_R3 LINE2L LINE2R PGA_L PGA_R DAC_L1 DAC_R1 MONO_LOP VOLUME CONTROLS, MIXING MONO_LOM Gain = 0dB to +9dB, Mute Figure 32. Architecture of the Output Stage Leading to the Fully Differential Line Output Drivers 38 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 LINE2L/MIC2L 0dB to -78dB LINE2R/MIC2R 0dB to -78dB PGA_L 0dB to -78dB + PGA_R 0dB to -78dB DAC_L1 0dB to -78dB DAC_R1 0dB to -78dB Figure 33. Detail of the Volume Control and Mixing Function Shown in Figure 28 and Figure 17 The DAC_L/R signals are the outputs of the stereo audio DAC, which can be steered by register control based on the requirements of the system. If mixing of the DAC audio with other signals is not required, and the DAC output is only needed at the stereo line outputs, then it is recommended to use the routing through path DAC_L3/R3 to the fully differential stereo line outputs. This results not only in higher quality output performance, but also in lower power operation, since the analog volume controls and mixing blocks ahead of these drivers can be powered down. If instead the DAC analog output must be routed to multiple output drivers simultaneously (such as to LEFT_LOP/M, RIGHT_LOP/M, and MONO_LOP/M) or must be mixed with other analog signals, then the DAC outputs should be switched through the DAC_L1/R1 path. This option provides the maximum flexibility for routing of the DAC analog signals to the output drivers The TLV320AIC33 includes an output level control on each output driver with limited gain adjustment from 0 dB to 9 dB. The output driver circuitry in this device are designed to provide a low distortion output while playing fullscale stereo DAC signals at a 0dB gain setting. However, a higher amplitude output can be obtained at the cost of increased signal distortion at the output. This output level control allows the user to make this tradeoff based on the requirements of the end equipment. Note that this output level control is not intended to be used as a standard output volume control. It is expected to be used only sparingly for level setting, i.e., adjustment of the fullscale output range of the device. Each differential line output driver can be powered down independently of the others when it is not needed in the system. When placed into powerdown through register programming, the driver output pins will be placed into a tri-stated, high-impedance state. ANALOG HIGH POWER OUTPUT DRIVERS The TLV320AIC33 includes four high power output drivers with extensive flexibility in their usage. These output drivers are individually capable of driving 30 mW each into a 16-Ω load in single-ended configuration, and they can be used in pairs to drive up to 500 mW into an 8-Ω load connected in bridge-terminated load (BTL) configuration between two driver outputs. The high power output drivers can be configured in a variety of ways, including: 1. driving up to two fully differential output signals 2. driving up to four single-ended output signals 3. driving two single-ended output signals, with one or two of the remaining drivers driving a fixed VCM level, for a pseudo-differential stereo output 4. driving one or two 8-Ω speakers connected BTL between pairs of driver output pins Submit Documentation Feedback 39 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 5. driving stereo headphones in single-ended configuration with two drivers, while the remaining two drivers are connected in BTL configuration to an 8-Ω speaker. The output stage architecture leading to the high power output drivers is shown in Figure 34, with the volume control and mixing blocks being effectively identical to that shown in Figure 33. Note that each of these drivers have a output level control block like those included with the line output drivers, allowing gain adjustment up to +9dB on the output signal. As in the previous case, this output level adjustment is not intended to be used as a standard volume control, but instead is included for additional fullscale output signal level control. Two of the output drivers, HPROUT and HPLOUT, include a direct connection path for the stereo DAC outputs to be passed directly to the output drivers and bypass the analog volume controls and mixing networks, using the DAC_L2/R2 path. As in the line output case, this functionality provides the highest quality DAC playback performance with reduced power dissipation, but can only be utilized if the DAC output does not need to route to multiple output drivers simultaneously, and if mixing of the DAC output with other analog signals is not needed. This direction connection path will attenuate the signal by a factor of 1dB. LINE2LP LINE2RP PGA_L PGA_R DAC_L1 DAC_R1 VOLUME CONTROLS, MIXING Volume Level 0dB to +9dB, mute HPLOUT DAC_L2 LINE2LM LINE2RM PGA_L PGA_R DAC_L1 DAC_R1 VOLUME CONTROLS, VCM Volume Level 0 dB to +9dB, mute HPLCOM MIXING LINE2LM LINE2RP PGA_L PGA_R DAC_L1 DAC_R1 VOLUME CONTROLS, MIXING VCM Volume Level 0 dB to +9dB, mute HPRCOM DAC_R2 LINE2LM LINE2RM PGA_L PGA_R DAC_L1 DAC_R1 VOLUME CONTROLS, MIXING Volume Level 0dB to +9dB, mute HPROUT Figure 34. Architecture of the output stage leading to the high power output drivers 40 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 The high power output drivers include additional circuitry to avoid artifacts on the audio output during power-on and power-off transient conditions. The user should first program the type of output configuration being used in Page-0/Reg-14, to allow the device to select the optimal power-up scheme to avoid output artifacts. The power-up delay time for the high power output drivers is also programmable over a wide range of time delays, from instantaneous up to 4-sec, using Page-0/Reg-42. When these output drivers are powered down, they can be placed into a variety of output conditions based on register programming. If lowest power operation is desired, then the outputs can be placed into a tri-state condition, and all power to the output stage is removed. However, this generally results in the output nodes drifting to rest near the upper or lower analog supply, due to small leakage currents at the pins. This then results in a longer delay requirement to avoid output artifacts during driver power-on. In order to reduce this required power-on delay, the TLV320AIC33 includes an option for the output pins of the drivers to be weakly driven to the VCM level they would normally rest at when powered with no signal applied. This output VCM level is determined by an internal bandgap voltage reference, and thus results in extra power dissipation when the drivers are in powerdown. However, this option provides the fastest method for transitioning the drivers from powerdown to full power operation without any output artifact introduced. The device includes a further option that falls between the other two – while it requires less power drawn while the output drivers are in powerdown, it also takes a slightly longer delay to power-up without artifact than if the bandgap reference is kept alive. In this alternate mode, the powered-down output driver pin is weakly driven to a voltage of approximately half the DRVDD1/2 supply level using an internal voltage divider. This voltage will not match the actual VCM of a fully powered driver, but due to the output voltage being close to its final value, a much shorter power-up delay time setting can be used and still avoid any audible output artifacts. These output voltage options are controlled in Page-0/Reg-42. The high power output drivers can also be programmed to power up first with the output level control in a highly attenuated state, then the output driver will automatically slowly reduce the output attenuation to reach the desired output level setting programmed. This capability is enabled by default but can be enabled in Page-0/Reg-40. SHORT CIRCUIT OUTPUT PROTECTION The TLV320AIC33 includes programmable short-circuit protection for the high power output drivers, for maximum flexibility in a given application. By default, if these output drivers are shorted, they will automatically limit the maximum amount of current that can be sourced to or sunk from a load, thereby protecting the device from an over-current condition. In this mode, the user can read Page-0/Reg-95 to determine whether the part is in short-circuit protection or not, and then decide whether to program the device to power down the output drivers. However, the device includes further capability to automatically power down an output driver whenever it does into short-circuit protection, without requiring intervention from the user. In this case, the output driver will stay in a power down condition until the user specifically programs it to power down and then power back up again, to clear the short-circuit flag. JACK / HEADSET DETECTION The TLV320AIC33 includes extensive capability to monitor a headphone, microphone, or headset jack, determine if a plug has been inserted into the jack, and then determine what type of headset/headphone is wired to the plug. Figure 35 shows one configuration of the device that enables detection and determination of headset type when a pseudo-differential (capless) stereo headphone output configuration is used. The registers used for this function are Page-0/Reg 14, 37, 38, and 13. The type of headset detected can be read back from Page-0/Reg-13. Note that for best results, it is recommended to select a MICBIAS value as high as possible, and to program the output driver common-mode level at a 1.35V or 1.5V level. Submit Documentation Feedback 41 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 AVDD Stereo g s MICBIAS MICDET s To Detection block MIC3(L/R) Cellular g m s HPLOUT Stereo + Cellular g m s s HPROUT m = mic HPRCOM s = speaker To detection block 1.35 HPLCOM g = ground/midbias Figure 35. Configuration of device for jack detection using a pseudo-differential (capless) headphone output connection. A modified output configuration used when the output drivers are ac-coupled is shown in Figure 36. Note that in this mode, the device cannot accurately determine the type of headset inserted if a mono or stereo headphone. Stereo g s MICBIAS MICDET s AVDD To Detection block MIC3(L/R) Cellular g m s HPLOUT Stereo + Cellular g m s s HPROUT m = mic s = speaker g = ground/midbias Figure 36. Configuration of device for jack detection using an ac-coupled stereo headphone output connection. An output configuration for the case of the outputs driving fully differential stereo headphones is shown in Figure 37. In this mode there is a requirement on the jack side that either HPLCOM or HPLOUT get shorted to ground if the plug is removed, which can be implemented using a spring terminal in a jack. For this mode to function properly, short-circuit detection should be enabled and configured to power-down the drivers if a short-circuit is detected. The registers that control this functionality are in Page-0/Reg-38/Bit-D2-D1. 42 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 This switch closes when MICDET jack is removed To Detection block HPLOUT HPLCOM HPRCOM HPROUT Figure 37. Configuration of device for jack detection using a fully differential stereo headphone output connection. GENERAL PURPOSE I/O AIC33 has two dedicated pins for General Purpose IO. These pins can be used to read status of external signals through register read when configured as General Purpose Input. When configured as General Purpose Output , these pins can also drive logic high or low. Besides these standard GPIO functions, these pins can also be used in a variety of ways such as output for internal clocks and interrupt signals. AIC33 generates a variety of interrupts of use to the host processor such interrupts on jack detection, button press, short circuit detection and AGC noise detection. All these interrupts can be routed individually to the GPIO pins or can be combined by a logical OR. In case of a combined interrupt, user can read an internal status register to find the actual cause of interrupt. When configured as interrupt, AIC33 also offers the flexibility of generating a single pulse or a train of pulses till the interrupt status register is read by the user. CONTROL REGISTERS The control registers for the TLV320AIC33 are described in detail below. All registers are 8 bit in width, with D7 referring to the most significant bit of each register, and D0 referring to the least significant bit. Page 0 / Register 0: BIT (1) (1) READ/ WRITE RESET VALUE D7–D1 X 0000000 D0 R/W 0 Page Select Register DESCRIPTION Reserved, write only zeros to these register bits Page Select Bit Writing zero to this bit sets Page-0 as the active page for following register accesses. Writing a one to this bit sets Page-1 as the active page for following register accesses. It is recommended that the user read this register bit back after each write, to ensure that the proper page is being accessed for future register read/writes. When resetting registers related to routing and volume controls of output drivers, it is recommended to reset them by writing directly to the registers instead of using software reset. Submit Documentation Feedback 43 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 1: BIT READ/ WRITE RESET VALUE D7 W 0 D6–D0 W 0000000 DESCRIPTION Software Reset Bit 0 : Don’t Care 1 : Self clearing software reset Reserved; don’t write Page 0 / Register 2: Codec Sample Rate Select Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D4 R/W 0000 ADC Sample Rate Select 0000: ADC Fs = Fsref/1 0001: ADC Fs = Fsref/1.5 0010: ADC Fs = Fsref/2 0011: ADC Fs = Fsref/2.5 0100: ADC Fs = Fsref/3 0101: ADC Fs = Fsref/3.5 0110: ADC Fs = Fsref/4 0111: ADC Fs = Fsref/4.5 1000: ADC Fs = Fsref/5 1001: ADC Fs = Fsref/5.5 1010: ADC Fs = Fsref / 6 1011–1111: Reserved, do not write these sequences. D3-D0 R/W 0000 DAC Sample Rate Select 0000 : DAC Fs = Fsref/1 0001 : DAC Fs = Fsref/1.5 0010 : DAC Fs = Fsref/2 0011 : DAC Fs = Fsref/2.5 0100 : DAC Fs = Fsref/3 0101 : DAC Fs = Fsref/3.5 0110 : DAC Fs = Fsref/4 0111 : DAC Fs = Fsref/4.5 1000 : DAC Fs = Fsref/5 1001: DAC Fs = Fsref/5.5 1010: DAC Fs = Fsref / 6 1011–1111 : Reserved, do not write these sequences. Page 0 / Register 3: 44 Software Reset Register BIT READ/ WRITE RESET VALUE D7 R/W 0 D6–D3 R/W 0010 PLL Q Value 0000: Q = 16 0001 : Q = 17 0010 : Q = 2 0011 : Q = 3 0100 : Q = 4 … 1110: Q = 14 1111: Q = 15 D2–D0 R/W 000 PLL P Value 000: P = 8 001: P = 1 010: P = 2 011: P = 3 100: P = 4 101: P = 5 110: P = 6 111: P = 7 PLL Programming Register A DESCRIPTION PLL Control Bit 0: PLL is disabled 1: PLL is enabled Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 4: BIT READ/ WRITE RESET VALUE D7–D2 R/W 000001 D1–D0 R/W 00 DESCRIPTION PLL J Value 000000: Reserved, do not write this sequence 000001: J = 1 000010: J = 2 000011: J = 3 … 111110: J = 62 111111: J = 63 Reserved, write only zeros to these bits Page 0 / Register 5: (1) PLL Programming Register B PLL Programming Register C (1) BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 00000000 PLL D value – Eight most significant bits of a 14-bit unsigned integer valid values for D are from zero to 9999, represented by a 14-bit integer located in Page-0/Reg-5-6. Values should not be written into these registers that would result in a D value outside the valid range. Note that whenever the D value is changed, register 5 should be written, immediately followed by register 6. Even if only the MSB or LSB of the value changes, both registers should be written. Page 0 / Register 6: BIT READ/ WRITE RESET VALUE D7–D2 R/W 00000000 D1-D0 R 00 PLL Programming Register D DESCRIPTION PLL D value – Six least significant bits of a 14-bit unsigned integer valid values for D are from zero to 9999, represented by a 14-bit integer located in Page-0/Reg-5-6. Values should not be written into these registers that would result in a D value outside the valid range. Reserved, write only zeros to these bits. Page 0 / Register 7: Codec Datapath Setup Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R/W 0 Fsref setting This register setting controls timers related to the AGC time constants. 0: Fsref = 48-kHz 1: Fsref = 44.1-kHz D6 R/W 0 ADC Dual rate control 0: ADC dual rate mode is disabled 1: ADC dual rate mode is enabled Note: ADC Dual Rate Mode must match DAC Dual Rate Mode D5 R/W 0 DAC Dual Rate Control 0: DAC dual rate mode is disabled 1: DAC dual rate mode is enabled D4–D3 R/W 00 Left DAC Datapath Control 00: Left DAC datapath is off (muted) 01: Left DAC datapath plays left channel input data 10: Left DAC datapath plays right channel input data 11: Left DAC datapath plays mono mix of left and right channel input data D2–D1 R/W 00 Right DAC Datapath Control 00: Right DAC datapath is off (muted) 01: Right DAC datapath plays right channel input data 10: Right DAC datapath plays left channel input data 11: Right DAC datapath plays mono mix of left and right channel input data D0 R/W 0 Reserved. Only write zero to this register. Submit Documentation Feedback 45 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 8: Audio Serial Data Interface Control Register A BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R/W 0 Bit Clock Directional Control 0: Bit clock is an input (slave mode) 1: Bit clock is an output (master mode) D6 R/W 0 Word Clock Directional Control 0: Word clock is an input (slave mode) 1: Word clock is an output (master mode) D5 R/W 0 Serial Output Data Driver (DOUT) 3-state control 0: Do not 3-state DOUT when valid data is not being sent 1: 3-state DOUT when valid data is not being sent D4 R/W 0 Bit/ Word Clock Drive Control 0: Bit clock and word clock will not be transmitted when in master mode if codec is powered down 1: Bit clock and word clock will continue to be transmitted when in master mode, even if codec is powered down D3 R/W 0 Reserved. Only write zero to this bit. D2 R/W 0 3-D Effect Control 0: Disable 3-D digital effect processing 1: Enable 3-D digital effect processing D1-D0 R/W 00 Digital Microphone Functionality Control 00: Digital microphone support is disabled 01: Digital microphone support is enabled with an oversampling rate of 128 10: Digital microphone support is enabled with an oversampling rate of 64 11: Digital microphone support is enabled with an oversampling rate of 32 Page 0 / Register 9: Audio Serial Data Interface Control Register B BIT READ/ WRITE RESET VALUE DESCRIPTION D7–D6 R/W 00 Audio Serial Data Interface Transfer Mode 00: Serial data bus uses I2S mode 01: Serial data bus uses DSP mode 10: Serial data bus uses right-justified mode 11: Serial data bus uses left-justified mode D5–D4 R/W 00 Audio Serial Data Word Length Control 00: Audio data word length = 16-bits 01: Audio data word length = 20-bits 10: Audio data word length = 24-bits 11: Audio data word length = 32-bits D3 R/W 0 Bit Clock Rate Control This register only has effect when bit clock is programmed as an output 0: Continuous-transfer mode used to determine master mode bit clock rate 1: 256-clock transfer mode used, resulting in 256 bit clocks per frame D2 R/W 0 DAC Re-Sync 0: Don’t Care 1: D1 R/W 0 ADC Re-Sync 0: Don’t Care 1: D0 46 R/W Re-Sync Stereo DAC with Codec Interface if the group delay changes by more than ±DACFS/4. Re-Sync Stereo ADC with Codec Interface if the group delay changes by more than ±ADCFS/4. Re-Sync Mute Behavior 0: Re-Sync is done without soft-muting the channel. (ADC/DAC) 1: Re-Sync is done by internally soft-muting the channel. (ADC/DAC) Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 10: Audio Serial Data Interface Control Register C BIT READ/ WRITE RESET VALUE DESCRIPTION D7–D0 R/W 00000000 Audio Serial Data Word Offset Control This register determines where valid data is placed or expected in each frame, by controlling the offset from beginning of the frame where valid data begins. The offset is measured from the rising edge of word clock when in DSP mode. 00000000: Data offset = 0 bit clocks 00000001: Data offset = 1 bit clock 00000010: Data offset = 2 bit clocks … Note: In continuous transfer mode the maximum offset is 17 for I2S/LJF/RJF modes and 16 for DSP mode. In 256-clock mode, the maximum offset is 242 for I2S/LJF/RJF and 241 for DSP modes. 11111110: Data offset = 254 bit clocks 11111111: Data offset = 255 bit clocks Page 0 / Register 11: Audio Codec Overflow Flag Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R 0 Left ADC Overflow Flag This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is removed. The register bit reset to 0 after it is read. 0: No overflow has occurred 1: An overflow has occurred D6 R 0 Right ADC Overflow Flag This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is removed. The register bit reset to 0 after it is read. 0: No overflow has occurred 1: An overflow has occurred D5 R 0 Left DAC Overflow Flag This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is removed. The register bit reset to 0 after it is read. 0: No overflow has occurred 1: An overflow has occurred D4 R 0 Right DAC Overflow Flag This is a sticky bit, so will stay set if an overflow occurs, even if the overflow condition is removed. The register bit reset to 0 after it is read. 0: No overflow has occurred 1: An overflow has occurred D3–D0 R/W 0001 PLL R Value 0000: R = 16 0001 : R = 1 0010 : R = 2 0011 : R = 3 0100 : R = 4 … 1110: R = 14 1111: R = 15 Page 0 / Register 12: Audio Codec Digital Filter Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7–D6 R/W 00 Left ADC Highpass Filter Control 00: Left ADC highpass filter disabled 01: Left ADC highpass filter –3-dB frequency = 0.0045 × ADC Fs 10: Left ADC highpass filter –3-dB frequency = 0.0125 × ADC Fs 11: Left ADC highpass filter –3-dB frequency = 0.025 × ADC Fs D5–D4 R/W 00 Right ADC Highpass Filter Control 00: Right ADC highpass filter disabled 01: Right ADC highpass filter –3-dB frequency = 0.0045 × ADC Fs 10: Right ADC highpass filter –3-dB frequency = 0.0125 × ADC Fs 11: Right ADC highpass filter –3-dB frequency = 0.025 × ADC Fs Submit Documentation Feedback 47 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 12: 48 Audio Codec Digital Filter Control Register (continued) BIT READ/ WRITE RESET VALUE DESCRIPTION D3 R/W 0 Left DAC Digital Effects Filter Control 0: Left DAC digital effects filter disabled (bypassed) 1: Left DAC digital effects filter enabled D2 R/W 0 Left DAC De-emphasis Filter Control 0: Left DAC de-emphasis filter disabled (bypassed) 1: Left DAC de-emphasis filter enabled D1 R/W 0 Right DAC Digital Effects Filter Control 0: Right DAC digital effects filter disabled (bypassed) 1: Right DAC digital effects filter enabled D0 R/W 0 Right DAC De-emphasis Filter Control 0: Right DAC de-emphasis filter disabled (bypassed) 1: Right DAC de-emphasis filter enabled Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 13: Headset / Button Press Detection Register A BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R/W 0 Headset Detection Control 0: Headset detection disabled 1: Headset detection enabled D6-D5 R 00 Headset Type Detection Results 00: No headset detected 01: Stereo headset detected 10: Cellular headset detected 11: Stereo + cellular headset detected D4-D2 R/W 000 Headset Glitch Suppression Debounce Control for Jack Detection 000: Debounce = 16msec( sampled with 2ms clock) 001: Debounce = 32msec( sampled with 4ms clock) 010: Debounce = 64msec( sampled with 8ms clock) 011: Debounce = 128msec( sampled with 16ms clock) 100: Debounce = 256msec( sampled with 32ms clock) 101: Debounce = 512msec( sampled with 64ms clock) 110: Reserved, do not write this bit sequence to these register bits. 111: Reserved, do not write this bit sequence to these register bits. D1-D0 R/W 00 Headset Glitch Suppression Debounce Control for Button Press 00: Debounce = 0msec 01: Debounce = 8msec(sampled with 1ms clock) 10: Debounce = 16msec(sampled with 2ms clock) 11: Debounce = 32msec(sampled with 4ms clock) BIT READ/ WRITE RESET VALUE D7 R/W 0 Driver Capacitive Coupling 0: Programs high-power outputs for capless driver configuration 1: Programs high-power outputs for ac-coupled driver configuration D6 (1) R/W 0 Stereo Output Driver Configuration A Note: do not set bits D6 and D3 both high at the same time. 0: A stereo fully-differential output configuration is not being used 1: A stereo fully-differential output configuration is being used D5 R 0 Button Press Detection Flag This register is a sticky bit, and will stay set to 1 after a button press has been detected, until the register is read. Upon reading this register, the bit is reset to zero. 0: A button press has not been detected 1: A button press has been detected D4 R 0 Headset Detection Flag 0: A headset has not been detected 1: A headset has been detected D3 (1) R/W 0 Stereo Output Driver Configuration B Note: do not set bits D6 and D3 both high at the same time. 0: A stereo pseudo-differential output configuration is not being used 1: A stereo pseudo-differential output configuration is being used D2–D0 R 000 Page 0 / Register 14: (1) Headset / Button Press Detection Register B DESCRIPTION Reserved. Write only zeros to these bits. Do not set D6 and D3 to 1 simultaneously Page 0 / Register 15: BIT READ/ WRITE RESET VALUE D7 R/W 1 Left ADC PGA Gain Control Register DESCRIPTION Left ADC PGA Mute 0: The left ADC PGA is not muted 1: The left ADC PGA is muted Submit Documentation Feedback 49 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 15: BIT READ/ WRITE RESET VALUE D6-D0 R/W 0000000 Left ADC PGA Gain Control Register (continued) DESCRIPTION Left ADC PGA Gain Setting 0000000: Gain = 0.0-dB 0000001: Gain = 0.5-dB 0000010: Gain = 1.0-dB … 1110110: Gain = 59.0-dB 1110111: Gain = 59.5-dB 1111000: Gain = 59.5-dB … 1111111: Gain = 59.5-dB Page 0 / Register 16: BIT READ/ WRITE RESET VALUE D7 R/W 1 D6-D0 R/W 0000000 DESCRIPTION Right ADC PGA Mute 0: The right ADC PGA is not muted 1: The right ADC PGA is muted Right ADC PGA Gain Setting 0000000: Gain = 0.0-dB 0000001: Gain = 0.5-dB 0000010: Gain = 1.0-dB … 1110110: Gain = 59.0-dB 1110111: Gain = 59.5-dB 1111000: Gain = 59.5-dB … 1111111: Gain = 59.5-dB Page 0 / Register 17: 50 Right ADC PGA Gain Control Register MIC3L/R to Left ADC Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D4 R/W 1111 MIC3L Input Level Control for Left ADC PGA Mix Setting the input level control to a gain below automatically connects MIC3L to the left ADC PGA mix 0000: Input level control gain = 0.0-dB 0001: Input level control gain = –1.5-dB 0010: Input level control gain = –3.0-dB 0011: Input level control gain = –4.5-dB 0100: Input level control gain = –6.0-dB 0101: Input level control gain = –7.5-dB 0110: Input level control gain = –9.0-dB 0111: Input level control gain = –10.5-dB 1000: Input level control gain = –12.0-dB 1001–1110: Reserved. Do not write these sequences to these register bits 1111: MIC3L is not connected to the left ADC PGA D3-D0 R/W 1111 MIC3R Input Level Control for Left ADC PGA Mix Setting the input level control to a gain below automatically connects MIC3R to the left ADC PGA mix 0000: Input level control gain = 0.0-dB 0001: Input level control gain = –1.5-dB 0010: Input level control gain = –3.0-dB 0011: Input level control gain = –4.5-dB 0100: Input level control gain = –6.0-dB 0101: Input level control gain = –7.5-dB 0110: Input level control gain = –9.0-dB 0111: Input level control gain = –10.5-dB 1000: Input level control gain = –12.0-dB 1001–1110: Reserved. Do not write these sequences to these register bits 1111: MIC3R is not connected to the left ADC PGA Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 18: MIC3L/R to Right ADC Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7–D4 R/W 1111 MIC3L Input Level Control for Right ADC PGA Mix Setting the input level control to a gain below automatically connects MIC3L to the right ADC PGA mix 0000: Input level control gain = 0.0-dB 0001: Input level control gain = –1.5-dB 0010: Input level control gain = –3.0-dB 0011: Input level control gain = –4.5-dB 0100: Input level control gain = –6.0-dB 0101: Input level control gain = –7.5-dB 0110: Input level control gain = –9.0-dB 0111: Input level control gain = –10.5-dB 1000: Input level control gain = –12.0-dB 1001–1110: Reserved. Do not write these sequences to these register bits 1111: MIC3L is not connected to the right ADC PGA D3–D0 R/W 1111 MIC3R Input Level Control for Right ADC PGA Mix Setting the input level control to a gain below automatically connects MIC3R to the right ADC PGA mix 0000: Input level control gain = 0.0-dB 0001: Input level control gain = –1.5-dB 0010: Input level control gain = –3.0-dB 0011: Input level control gain = –4.5-dB 0100: Input level control gain = –6.0-dB 0101: Input level control gain = –7.5-dB 0110: Input level control gain = –9.0-dB 0111: Input level control gain = –10.5-dB 1000: Input level control gain = –12.0-dB 1001–1110: Reserved. Do not write these sequences to these register bits 1111: MIC3R is not connected to right ADC PGA Page 0 / Register 19: LINE1L to Left ADC Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R/W 0 D6–D3 R/W 1111 D2 R/W 0 Left ADC Channel Power Control 0: Left ADC channel is powered down 1: Left ADC channel is powered up D1–D0 R/W 00 Left ADC PGA Soft-Stepping Control 00: Left ADC PGA soft-stepping at once per Fs 01: Left ADC PGA soft-stepping at once per two Fs 10–11: Left ADC PGA soft-stepping is disabled LINE1L Single-Ended vs Fully Differential Control If LINE1L is selected to both left and right ADC channels, both connections must use the same configuration (single-ended or fully differential mode). 0: LINE1L is configured in single-ended mode 1: LINE1L is configured in fully differential mode LINE1L Input Level Control for Left ADC PGA Mix Setting the input level control to a gain below automatically connects LINE1L to the left ADC PGA mix 0000: Input level control gain = 0.0-dB 0001: Input level control gain = –1.5-dB 0010: Input level control gain = –3.0-dB 0011: Input level control gain = –4.5-dB 0100: Input level control gain = –6.0-dB 0101: Input level control gain = –7.5-dB 0110: Input level control gain = –9.0-dB 0111: Input level control gain = –10.5-dB 1000: Input level control gain = –12.0-dB 1001–1110: Reserved. Do not write these sequences to these register bits 1111: LINE1L is not connected to the left ADC PGA Submit Documentation Feedback 51 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 20: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6–D3 R/W 1111 D2 R/W 0 D1-D0 (1) R 00 DESCRIPTION LINE2L Single-Ended vs Fully Differential Control If LINE2L is selected to both left and right ADC channels, both connections must use the same configuration (single-ended or fully differential mode). 0: LINE2L is configured in single-ended mode 1: LINE2L is configured in fully differential mode LINE2L Input Level Control for Left ADC PGA Mix Setting the input level control to a gain below automatically connects LINE2L to the left ADC PGA mix 0000: Input level control gain = 0.0-dB 0001: Input level control gain = –1.5-dB 0010: Input level control gain = –3.0-dB 0011: Input level control gain = –4.5-dB 0100: Input level control gain = –6.0-dB 0101: Input level control gain = –7.5-dB 0110: Input level control gain = –9.0-dB 0111: Input level control gain = –10.5-dB 1000: Input level control gain = –12.0-dB 1001–1110: Reserved. Do not write these sequences to these register bits 1111: LINE2L is not connected to the left ADC PGA Left ADC Channel Weak Common-Mode Bias Control 0: Left ADC channel unselected inputs are not biased weakly to the ADC common-mode voltage 1: Left ADC channel unselected inputs are biased weakly to the ADC common- mode voltage Reserved. Write only zeros to these register bits LINE1R SEvsFD control is available for both left and right channels. However this setting must be same for both the channels. Page 0 / Register 21: LINE1R to Left ADC Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R/W 0 LINE1R Single-Ended vs Fully Differential Control If LINE1R is selected to both left and right ADC channels, both connections must use the same configuration (single-ended or fully differential mode). 0: LINE1R is configured in single-ended mode 1: LINE1R is configured in fully differential mode D6–D3 R/W 1111 LINE1R Input Level Control for Left ADC PGA Mix Setting the input level control to a gain below automatically connects LINE1R to the left ADC PGA mix 0000: Input level control gain = 0.0-dB 0001: Input level control gain = –1.5-dB 0010: Input level control gain = –3.0-dB 0011: Input level control gain = –4.5-dB 0100: Input level control gain = –6.0-dB 0101: Input level control gain = –7.5-dB 0110: Input level control gain = –9.0-dB 0111: Input level control gain = –10.5-dB 1000: Input level control gain = –12.0-dB 1001–1110: Reserved. Do not write these sequences to these register bits 1111: LINE1R is not connected to the left ADC PGA D2–D0 R 000 Reserved. Write only zeros to these register bits. Page 0 / Register 22: 52 LINE2L to Left (1) ADC Control Register LINE1R to Right ADC Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R/W 0 LINE1R Single-Ended vs Fully Differential Control If LINE1R is selected to both left and right ADC channels, both connections must use the same configuration (single-ended or fully differential mode). 0: LINE1R is configured in single-ended mode 1: LINE1R is configured in fully differential mode Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 22: LINE1R to Right ADC Control Register (continued) BIT READ/ WRITE RESET VALUE DESCRIPTION D6–D3 R/W 1111 D2 R/W 0 Right ADC Channel Power Control 0: Right ADC channel is powered down 1: Right ADC channel is powered up D1–D0 R/W 00 Right ADC PGA Soft-Stepping Control 00: Right ADC PGA soft-stepping at once per Fs 01: Right ADC PGA soft-stepping at once per two Fs 10-11: Right ADC PGA soft-stepping is disabled LINE1R Input Level Control for Right ADC PGA Mix Setting the input level control to a gain below automatically connects LINE1R to the right ADC PGA mix 0000: Input level control gain = 0.0-dB 0001: Input level control gain = –1.5-dB 0010: Input level control gain = –3.0-dB 0011: Input level control gain = –4.5-dB 0100: Input level control gain = –6.0-dB 0101: Input level control gain = –7.5-dB 0110: Input level control gain = –9.0-dB 0111: Input level control gain = –10.5-dB 1000: Input level control gain = –12.0-dB 1001–1110: Reserved. Do not write these sequences to these register bits 1111: LINE1R is not connected to the right ADC PGA Page 0 / Register 23: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6–D3 R/W 1111 D2 R/W 0 D1–D0 R 00 LINE2R to Right ADC Control Register DESCRIPTION LINE2R Single-Ended vs Fully Differential Control If LINE2R is selected to both left and right ADC channels, both connections must use the same configuration (single-ended or fully differential mode). 0: LINE2R is configured in single-ended mode 1: LINE2R is configured in fully differential mode LINE2R Input Level Control for Right ADC PGA Mix Setting the input level control to a gain below automatically connects LINE2R to the right ADC PGA mix 0000: Input level control gain = 0.0-dB 0001: Input level control gain = -–1.5-dB 0010: Input level control gain = –3.0-dB 0011: Input level control gain = –4.5-dB 0100: Input level control gain = –6.0-dB 0101: Input level control gain = –7.5-dB 0110: Input level control gain = –9.0-dB 0111: Input level control gain = –10.5-dB 1000: Input level control gain = –12.0-dB 1001-1110: Reserved. Do not write these sequences to these register bits 1111: LINE2R is not connected to the right ADC PGA Right ADC Channel Weak Common-Mode Bias Control 0: Right ADC channel unselected inputs are not biased weakly to the ADC common-mode voltage 1: Right ADC channel unselected inputs are biased weakly to the ADC common- mode voltage Reserved. Write only zeros to these register bits Page 0 / Register 24: BIT READ/ WRITE RESET VALUE D7 R/W 0 LINE1L to Right ADC Control Register DESCRIPTION LINE1L Single-Ended vs Fully Differential Control If LINE1L is selected to both left and right ADC channels, both connections must use the same configuration (single-ended or fully differential mode). 0: LINE1L is configured in single-ended mode 1: LINE1L is configured in fully differential mode Submit Documentation Feedback 53 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 24: LINE1L to Right ADC Control Register (continued) BIT READ/ WRITE RESET VALUE DESCRIPTION D6–D3 R/W 1111 LINE1L Input Level Control for Right ADC PGA Mix Setting the input level control to a gain below automatically connects LINE1L to the right ADC PGA mix 0000: Input level control gain = 0.0-dB 0001: Input level control gain = –1.5-dB 0010: Input level control gain = –3.0-dB 0011: Input level control gain = –4.5-dB 0100: Input level control gain = –6.0-dB 0101: Input level control gain = –7.5-dB 0110: Input level control gain = –9.0-dB 0111: Input level control gain = –10.5-dB 1000: Input level control gain = –12.0-dB 1001–1110: Reserved. Do not write these sequences to these register bits 1111: LINE1L is not connected to the right ADC PGA D2–D0 R 000 Reserved. Write only zeros to these register bits. Page 0 / Register 25: BIT READ/ WRITE RESET VALUE DESCRIPTION D7–D6 R/W 00 MICBIAS Level Control 00: MICBIAS output is powered down 01: MICBIAS output is powered to 2.0 V 10: MICBIAS output is powered to 2.5 V 11: MICBIAS output is connected to AVDD D5–D3 R 000 Reserved. Write only zeros to these register bits. D2–D0 R XXX Reserved. Write only zeros to these register bits. Page 0 / Register 26: (1) 54 MICBIAS Control Register BIT READ/ WRITE RESET VALUE D7 R/W 0 D6–D4 R/W 000 Left AGC Control Register A DESCRIPTION Left AGC Enable 0: Left AGC is disabled 1: Left AGC is enabled Left AGC Target Gain 000: Left AGC target gain = 001: Left AGC target gain = 010: Left AGC target gain = 011: Left AGC target gain = 100: Left AGC target gain = 101: Left AGC target gain = 110: Left AGC target gain = 111: Left AGC target gain = –5.5-dB –8-dB –10-dB –12-dB –14-dB –17-dB –20-dB –24-dB D3–D2 R/W 00 Left AGC Attack Time These time constants (1) will not be accurate when double rate audio mode is enabled. 00: Left AGC attack time = 8-msec 01: Left AGC attack time = 11-msec 10: Left AGC attack time = 16-msec 11: Left AGC attack time = 20-msec D1–D0 R/W 00 Left AGC Decay Time These time constants (1) will not be accurate when double rate audio mode is enabled. 00: Left AGC decay time = 100-msec 01: Left AGC decay time = 200-msec 10: Left AGC decay time = 400-msec 11: Left AGC decay time = 500-msec Time constants are valid when DRA is not enabled. The values would change if DRA is enabled. Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 27: Left AGC Control Register B BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D1 R/W 1111111 Left AGC Maximum Gain Allowed 0000000: Maximum gain = 0.0-dB 0000001: Maximum gain = 0.5-dB 0000010: Maximum gain = 1.0-dB … 1110110: Maximum gain = 59.0-dB 1110111–111111: Maximum gain = 59.5-dB D0 R/W 0 Reserved. Write only zero to this register bit. Page 0 / Register 28: BIT READ/ WRITE RESET VALUE D7–D6 R/W 00 D5–D1 R/W 00000 D0 R/W 0 Left AGC Control Register C DESCRIPTION Noise Gate Hysteresis Level Control 00: Hysteresis is disabled 01: Hysteresis = 1-dB 10: Hysteresis = 2-dB 11: Hysteresis = 3-dB Left AGC Noise Threshold Control 00000: Left AGC Noise/Silence Detection disabled 00001: Left AGC noise threshold = –30-dB 00010: Left AGC noise threshold = –32-dB 00011: Left AGC noise threshold = –34-dB … 11101: Left AGC noise threshold = –86-dB 11110: Left AGC noise threshold = –88-dB 11111: Left AGC noise threshold = –90-dB Left AGC Clip Stepping Control 0: Left AGC clip stepping disabled 1: Left AGC clip stepping enabled Page 0 / Register 29: Right AGC Control Register A BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R/W 0 D6-D4 R/W 000 Right AGC Target Gain 000: Right AGC target gain = –5.5-dB 001: Right AGC target gain = –8-dB 010: Right AGC target gain = –10-dB 011: Right AGC target gain = –12-dB 100: Right AGC target gain = –14-dB 101: Right AGC target gain = –17-dB 110: Right AGC target gain = –20-dB 111: Right AGC target gain = –24-dB D3–D2 R/W 00 Right AGC Attack Time These time constants will not be accurate when double rate audio mode is enabled. 00: Right AGC attack time = 8-msec 01: Right AGC attack time = 11-msec 10: Right AGC attack time = 16-msec 11: Right AGC attack time = 20-msec D1–D0 R/W 00 Right AGC Decay Time These time constants will not be accurate when double rate audio mode is enabled. 00: Right AGC decay time = 100-msec 01: Right AGC decay time = 200-msec 10: Right AGC decay time = 400-msec 11: Right AGC decay time = 500-msec Right AGC Enable 0: Right AGC is disabled 1: Right AGC is enabled Submit Documentation Feedback 55 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 30: BIT READ/ WRITE RESET VALUE DESCRIPTION D7–D1 R/W 1111111 Right AGC Maximum Gain Allowed 0000000: Maximum gain = 0.0-dB 0000001: Maximum gain = 0.5-dB 0000010: Maximum gain = 1.0-dB … 1110110: Maximum gain = 59.0-dB 1110111–111111: Maximum gain = 59.5-dB D0 R/W 0 Reserved. Write only zero to this register bit. Page 0 / Register 31: BIT READ/ WRITE RESET VALUE D7–D6 R/W 00 D5–D1 R/W 00000 D0 R/W 0 Right AGC Control Register C DESCRIPTION Noise Gate Hysteresis Level Control 00: Hysteresis is disabled 01: Hysteresis = 1-dB 10: Hysteresis = 2-dB 11: Hysteresis = 3-dB Right AGC Noise Threshold Control 00000: Right AGC Noise/Silence Detection disabled 00001: Right AGC noise threshold = –30-dB 00010: Right AGC noise threshold = –32-dB 00011: Right AGC noise threshold = –34-dB … 11101: Right AGC noise threshold = –86-dB 11110: Right AGC noise threshold = –88-dB 11111: Right AGC noise threshold = –90-dB Right AGC Clip Stepping Control 0: Right AGC clip stepping disabled 1: Right AGC clip stepping enabled Page 0 / Register 32: BIT READ/ WRITE RESET VALUE D7–D0 R 00011000 BIT READ/ WRITE RESET VALUE D7-D0 R 00011000 Left AGC Gain Register DESCRIPTION Left Channel Gain Applied by AGC Algorithm 00000000: Gain = –12.0-dB 00000001: Gain = –11.5-dB 00000010: Gain = –11.0-dB … 00011000: Gain = 0.0-dB 00011001: Gain = +0.5-dB … 10000011: Gain = +59.0-dB 10000100: Gain = +59.5-dB Page 0 / Register 33: 56 Right AGC Control Register B Right AGC Gain Register DESCRIPTION Right Channel Gain Applied by AGC Algorithm 00000000: Gain = –12.0-dB 00000001: Gain = –11.5-dB 00000010: Gain = –11.0-dB … 00011000: Gain = 0.0-dB 00011001: Gain = +0.5-dB … 10000011: Gain = +59.0-dB 10000100: Gain = +59.5-dB Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 34: (1) BIT READ/ WRITE RESET VALUE DESCRIPTION D7–D3 R/W 00000 Left AGC Noise Detection Debounce Control These times (1) will not be accurate when double rate audio mode is enabled. 00000: Debounce = 0-msec 00001: Debounce = 0.5-msec 00010: Debounce = 1-msec 00011: Debounce = 2-msec 00100: Debounce = 4-msec 00101: Debounce = 8-msec 00110: Debounce = 16-msec 00111: Debounce = 32-msec 01000: Debounce = 64×1 = 64ms 01001: Debounce = 64×2 = 128ms 01010: Debounce = 64×3 = 192ms … 11110: Debounce = 64×23 = 1472ms 11111: Debounce = 64×24 = 1536ms D2–D0 R/W 000 Left AGC Signal Detection Debounce Control These times (1) will not be accurate when double rate audio mode is enabled. 000: Debounce = 0-msec 001: Debounce = 0.5-msec 010: Debounce = 1-msec 011: Debounce = 2-msec 100: Debounce = 4-msec 101: Debounce = 8-msec 110: Debounce = 16-msec 111: Debounce = 32-msec Time constants are valid when DRA is not enabled. The values would change when DRA is enabled Page 0 / Register 35: (1) Left AGC Noise Gate Debounce Register Right AGC Noise Gate Debounce Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7–D3 R/W 00000 Right AGC Noise Detection Debounce Control These times (1) will not be accurate when double rate audio mode is enabled. 00000: Debounce = 0-msec 00001: Debounce = 0.5-msec 00010: Debounce = 1-msec 00011: Debounce = 2-msec 00100: Debounce = 4-msec 00101: Debounce = 8-msec 00110: Debounce = 16-msec 00111: Debounce = 32-msec 01000: Debounce = 64×1 = 64ms 01001: Debounce = 64×2 = 128ms 01010: Debounce = 64×3 = 192ms … 11110: Debounce = 64×23 = 1472ms 11111: Debounce = 64×24 = 1536ms D2–D0 R/W 000 Right AGC Signal Detection Debounce Control These times (1) will not be accurate when double rate audio mode is enabled. 000: Debounce = 0-msec 001: Debounce = 0.5-msec 010: Debounce = 1-msec 011: Debounce = 2-msec 100: Debounce = 4-msec 101: Debounce = 8-msec 110: Debounce = 16-msec 111: Debounce = 32-msec Time constants are valid when DRA is not enabled. The values would change when DRA is enabled. Submit Documentation Feedback 57 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 36: ADC Flag Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R 0 Left ADC PGA Status 0: Applied gain and programmed gain are not the same 1: Applied gain = programmed gain D6 R 0 Left ADC Power Status 0: Left ADC is in a power down state 1: Left ADC is in a power up state D5 R 0 Left AGC Signal Detection Status 0: Signal power is greater than noise threshold 1: Signal power is less than noise threshold D4 R 0 Left AGC Saturation Flag 0: Left AGC is not saturated 1: Left AGC gain applied = maximum allowed gain for left AGC D3 R 0 Right ADC PGA Status 0: Applied gain and programmed gain are not the same 1: Applied gain = programmed gain D2 R 0 Right ADC Power Status 0: Right ADC is in a power down state 1: Right ADC is in a power up state D1 R 0 Right AGC Signal Detection Status 0: Signal power is greater than noise threshold 1: Signal power is less than noise threshold D0 R 0 Right AGC Saturation Flag 0: Right AGC is not saturated 1: Right AGC gain applied = maximum allowed gain for right AGC Page 0 / Register 37: DAC Power and Output Driver Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R/W 0 Left DAC Power Control 0: Left DAC not powered up 1: Left DAC is powered up D6 R/W 0 Right DAC Power Control 0: Right DAC not powered up 1: Right DAC is powered up D5–D4 R/W 00 HPLCOM Output Driver Configuration Control 00: HPLCOM configured as differential of HPLOUT 01: HPLCOM configured as constant VCM output 10: HPLCOM configured as independent single-ended output 11: Reserved. Do not write this sequence to these register bits. D3–D0 R 000 Reserved. Write only zeros to these register bits. Page 0 / Register 38: High Power Output Driver Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D6 R 00 Reserved. Write only zeros to these register bits. D5-D3 R/W 000 HPRCOM Output Driver Configuration Control 000: HPRCOM configured as differential of HPROUT 001: HPRCOM configured as constant VCM output 010: HPRCOM configured as independent single-ended output 011: HPRCOM configured as differential of HPLCOM 100: HPRCOM configured as external feedback with HPLCOM as constant VCM output 101–111: Reserved. Do not write these sequences to these register bits. 58 D2 R/W 0 Short Circuit Protection Control 0: Short circuit protection on all high power output drivers is disabled 1: Short circuit protection on all high power output drivers is enabled D1 R/W 0 Short Circuit Protection Mode Control Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 38: BIT D0 READ/ WRITE R High Power Output Driver Control Register (continued) RESET VALUE 0 DESCRIPTION 0: If short circuit protection enabled, it will limit the maximum current to the load 1: If short circuit protection enabled, it will power down the output driver automatically when a short is detected Reserved. Write only zero to this register bit. Page 0 / Register 39: BIT READ/ WRITE D7–D0 R RESET VALUE DESCRIPTION 00000000 Reserved. Do not write to this register. Page 0 / Register 40: High Power Output Stage Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7–D6 R/W 00 Output Common-Mode Voltage Control 00: Output common-mode voltage = 1.35V 01: Output common-mode voltage = 1.5V 10: Output common-mode voltage = 1.65V 11: Output common-mode voltage = 1.8V D5–D4 R/W 00 LINE2L Bypass Path Control 00: LINE2L bypass is disabled 01: LINE2L bypass uses LINE2LP single-ended 10: LINE2L bypass uses LINE2LM single-ended 11: LINE2L bypass uses LINE2LP/M differentially D3–D2 R/W 00 LINE2R Bypass Path Control 00: LINE2R bypass is disabled 01: LINE2R bypass uses LINE2RP single-ended 10: LINE2R bypass uses LINE2RM single-ended 11: LINE2R bypass uses LINE2RP/M differentially D1–D0 R/W 00 Output Volume Control Soft-Stepping 00: Output soft-stepping = one step per Fs 01: Output soft-stepping = one step per 2Fs 10: Output soft-stepping disabled 11: Reserved. Do not write this sequence to these register bits. Page 0 / Register 41: BIT READ/ WRITE RESET VALUE D7–D6 R/W 00 D5–D4 (1) Reserved Register R/W 00 DAC Output Switching Control Register DESCRIPTION Left DAC Output Switching Control 00: Left DAC output selects DAC_L1 path 01: Left DAC output selects DAC_L3 path to left line output driver 10: Left DAC output selects DAC_L2 path to left high power output drivers 11: Reserved. Do not write this sequence to these register bits. (1) Right DAC Output Switching Control 00: Right DAC output selects DAC_R1 path 01: Right DAC output selects DAC_R3 path to right line output driver 10: Right DAC output selects DAC_R2 path to right high power output drivers 11: Reserved. Do not write this sequence to these register bits. (1) D3–D2 R/W 00 Reserved. Write only zeros to these bits. D1–D0 R/W 00 DAC Digital Volume Control Functionality 00: Left and right DAC channels have independent volume controls 01: Left DAC volume follows the right channel control register 10: Right DAC volume follows the left channel control register 11: Left and right DAC channels have independent volume controls (same as 00) When using the DAC direct paths (DAC_L2 and DAC_R2), the signal will be gain up by a factor of -1dB. Submit Documentation Feedback 59 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 42: BIT READ/ WRITE RESET VALUE D7-D4 R/W 0000 D3-D2 R/W 00 Driver Ramp-up Step Timing Control 00: Driver ramp-up step time = 0-msec 01: Driver ramp-up step time = 1-msec 10: Driver ramp-up step time = 2-msec 11: Driver ramp-up step time = 4-msec D1 R/W 0 Weak Output Common-mode Voltage Control D0 R/W 0 DESCRIPTION Output Driver Power-On Delay Control 0000: Driver power-on time = 0-µsec 0001: Driver power-on time = 10-µsec 0010: Driver power-on time = 100-µsec 0011: Driver power-on time = 1-msec 0100: Driver power-on time = 10-msec 0101: Driver power-on time = 50-msec 0110: Driver power-on time = 100-msec 0111: Driver power-on time = 200-msec 1000: Driver power-on time = 400-msec 1001: Driver power-on time = 800-msec 1010: Driver power-on time = 2-sec 1011: Driver power-on time = 4-sec 1100–1111: Reserved. Do not write these sequences to these register bits. 0: Weakly driven output common-mode voltage is generated from resistor divider off the AVDD supply 1: Weakly driven output common-mode voltage is generated from bandgap reference Reserved. Write only zero to this register bit. Page 0 / Register 43: BIT READ/ WRITE RESET VALUE D7 R/W 1 D6–D0 R/W Left DAC Digital Volume Control Register DESCRIPTION Left DAC Digital Mute 0: The left DAC channel is not muted 1: The left DAC channel is muted 0000000 Left DAC Digital Volume Control Setting 0000000: Gain = 0.0-dB 0000001: Gain = –0.5-dB 0000010: Gain = –1.0-dB … 1111101: Gain = –62.5-dB 1111110: Gain = –63.0-dB 1111111: Gain = –63.5-dB Page 0 / Register 44: 60 Output Driver Pop Reduction Register BIT READ/ WRITE RESET VALUE D7 R/W 1 D6–D0 R/W 0000000 Right DAC Digital Volume Control Register DESCRIPTION Right DAC Digital Mute 0: The right DAC channel is not muted 1: The right DAC channel is muted Right DAC Digital Volume Control Setting 0000000: Gain = 0.0-dB 0000001: Gain = –0.5-dB 0000010: Gain = –1.0-dB … 1111101: Gain = –62.5-dB 1111110: Gain = –63.0-dB 1111111: Gain = –63.5-dB Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Output Stage Volume Controls A basic analog volume control with range from 0 dB to -78 dB and mute is replicated multiple times in the output stage network, connected to each of the analog signals that route to the output stage. In addition, to enable completely independent mixing operations to be performed for each output driver, each analog signal coming into the output stage may have up to seven separate volume controls. These volume controls all have approximately 0.5-dB step programmability over most of the gain range, with steps increasing slightly at the lowest attenuations. Table 4 lists the detailed gain versus programmed setting for this basic volume control. Table 4. Output Stage Volume Control Settings and Gains Gain Setting Analog Gain (dB) 0 0.0 Gain Setting Analog Gain (dB) Gain Setting Analog Gain (dB) Gain Setting Analog Gain (dB) 30 -15.0 60 -30.1 90 -45.2 1 -0.5 31 -15.5 61 -30.6 91 -45.8 2 -1.0 32 -16.0 62 -31.1 92 -46.2 3 -1.5 33 -16.5 63 -31.6 93 -46.7 4 -2.0 34 -17.0 64 -32.1 94 -47.4 5 -2.5 35 -17.5 65 -32.6 95 -47.9 6 -3.0 36 -18.0 66 -33.1 96 -48.2 7 -3.5 37 -18.6 67 -33.6 97 -48.7 8 -4.0 38 -19.1 68 -34.1 98 -49.3 9 -4.5 39 -19.6 69 -34.6 99 -50.0 10 -5.0 40 -20.1 70 -35.1 100 -50.3 11 -5.5 41 -20.6 71 -35.7 101 -51.0 12 -6.0 42 -21.1 72 -36.1 102 -51.4 13 -6.5 43 -21.6 73 -36.7 103 -51.8 14 -7.0 44 -22.1 74 -37.1 104 -52.2 15 -7.5 45 -22.6 75 -37.7 105 -52.7 16 -8.0 46 -23.1 76 -38.2 106 -53.7 17 -8.5 47 -23.6 77 -38.7 107 -54.2 18 -9.0 48 -24.1 78 -39.2 108 -55.3 19 -9.5 49 -24.6 79 -39.7 109 -56.7 20 -10.0 50 -25.1 80 -40.2 110 -58.3 21 -10.5 51 -25.6 81 -40.7 111 -60.2 22 -11.0 52 -26.1 82 -41.2 112 -62.7 23 -11.5 53 -26.6 83 -41.7 113 -64.3 24 -12.0 54 -27.1 84 -42.2 114 -66.2 25 -12.5 55 -27.6 85 -42.7 115 -68.7 26 -13.0 56 -28.1 86 -43.2 116 -72.2 27 -13.5 57 -28.6 87 -43.8 117 -78.3 28 -14.0 58 -29.1 88 -44.3 118–127 Mute 29 -14.5 59 -29.6 89 -44.8 Page 0 / Register 45: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 LINE2L to HPLOUT Volume Control Register DESCRIPTION LINE2L Output Routing Control 0: LINE2L is not routed to HPLOUT 1: LINE2L is routed to HPLOUT LINE2L to HPLOUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Submit Documentation Feedback 61 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 46: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 PGA_L to HPLOUT Volume Control Register DESCRIPTION PGA_L Output Routing Control 0: PGA_L is not routed to HPLOUT 1: PGA_L is routed to HPLOUT PGA_L to HPLOUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 47: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DAC_L1 to HPLOUT Volume Control Register DESCRIPTION DAC_L1 Output Routing Control 0: DAC_L1 is not routed to HPLOUT 1: DAC_L1 is routed to HPLOUT DAC_L1 to HPLOUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 48: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 LINE2R to HPLOUT Volume Control Register DESCRIPTION LINE2R Output Routing Control 0: LINE2R is not routed to HPLOUT 1: LINE2R is routed to HPLOUT LINE2R to HPLOUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 49: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 PGA_R to HPLOUT Volume Control Register DESCRIPTION PGA_R Output Routing Control 0: PGA_R is not routed to HPLOUT 1: PGA_R is routed to HPLOUT PGA_R to HPLOUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 50: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DAC_R1 to HPLOUT Volume Control Register DESCRIPTION DAC_R1 Output Routing Control 0: DAC_R1 is not routed to HPLOUT 1: DAC_R1 is routed to HPLOUT DAC_R1 to HPLOUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 51: BIT READ/ WRITE RESET VALUE D7-D4 R/W 0000 62 HPLOUT Output Level Control Register DESCRIPTION HPLOUT Output Level Control 0000: Output level control = 0-dB 0001: Output level control = 1-dB 0010: Output level control = 2-dB ... 1000: Output level control = 8-dB 1001: Output level control = 9-dB 1010–1111: Reserved. Do not write these sequences to these register bits. Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 51: HPLOUT Output Level Control Register (continued) BIT READ/ WRITE RESET VALUE DESCRIPTION D3 R/W 0 HPLOUT Mute 0: HPLOUT is muted 1: HPLOUT is not muted D2 R/W 1 HPLOUT Power Down Drive Control 0: HPLOUT is weakly driven to a common-mode when powered down 1: HPLOUT is tri-stated with powered down D1 R 0 HPLOUT Volume Control Status 0: All programmed gains to HPLOUT have been applied 1: Not all programmed gains to HPLOUT have been applied yet D0 R/W 0 HPLOUT Power Control 0: HPLOUT is not fully powered up 1: HPLOUT is fully powered up Page 0 / Register 52: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 LINE2L to HPLCOM Volume Control Register DESCRIPTION LINE2L Output Routing Control 0: LINE2L is not routed to HPLCOM 1: LINE2L is routed to HPLCOM LINE2L to HPLCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 53: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DESCRIPTION PGA_L Output Routing Control 0: PGA_L is not routed to HPLCOM 1: PGA_L is routed to HPLCOM PGA_L to HPLCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 54: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DAC_L1 to HPLCOM Volume Control Register DESCRIPTION DAC_L1 Output Routing Control 0: DAC_L1 is not routed to HPLCOM 1: DAC_L1 is routed to HPLCOM DAC_L1 to HPLCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 55: BIT PGA_L to HPLCOM Volume Control Register LINE2R to HPLCOM Volume Control Register DESCRIPTION LINE2R Output Routing Control 0: LINE2R is not routed to HPLCOM 1: LINE2R is routed to HPLCOM LINE2R to HPLCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Submit Documentation Feedback 63 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 56: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 PGA_R to HPLCOM Volume Control Register DESCRIPTION PGA_R Output Routing Control 0: PGA_R is not routed to HPLCOM 1: PGA_R is routed to HPLCOM PGA_R to HPLCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 57: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DAC_R1 to HPLCOM Volume Control Register DESCRIPTION DAC_R1 Output Routing Control 0: DAC_R1 is not routed to HPLCOM 1: DAC_R1 is routed to HPLCOM DAC_R1 to HPLCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 58: BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D4 R/W 0000 D3 R/W 0 HPLCOM Mute 0: HPLCOM is muted 1: HPLCOM is not muted D2 R/W 1 HPLCOM Power Down Drive Control 0: HPLCOM is weakly driven to a common-mode when powered down 1: HPLCOM is tri-stated with powered down D1 R 0 HPLCOM Volume Control Status 0: All programmed gains to HPLCOM have been applied 1: Not all programmed gains to HPLCOM have been applied yet D0 R/W 0 HPLCOM Power Control 0: HPLCOM is not fully powered up 1: HPLCOM is fully powered up HPLCOM Output Level Control 0000: Output level control = 0-dB 0001: Output level control = 1-dB 0010: Output level control = 2-dB ... 1000: Output level control = 8-dB 1001: Output level control = 9-dB 1010–1111: Reserved. Do not write these sequences to these register bits. Page 0 / Register 59: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 LINE2L to HPROUT Volume Control Register DESCRIPTION LINE2L Output Routing Control 0: LINE2L is not routed to HPROUT 1: LINE2L is routed to HPROUT LINE2L to HPROUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 60: 64 HPLCOM Output Level Control Register PGA_L to HPROUT Volume Control Register DESCRIPTION PGA_L Output Routing Control 0: PGA_L is not routed to HPROUT 1: PGA_L is routed to HPROUT PGA_L to HPROUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 61: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DAC_L1 to HPROUT Volume Control Register DESCRIPTION DAC_L1 Output Routing Control 0: DAC_L1 is not routed to HPROUT 1: DAC_L1 is routed to HPROUT DAC_L1 to HPROUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 62: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 LINE2R to HPROUT Volume Control Register DESCRIPTION LINE2R Output Routing Control 0: LINE2R is not routed to HPROUT 1: LINE2R is routed to HPROUT LINE2R to HPROUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 63: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 PGA_R to HPROUT Volume Control Register DESCRIPTION PGA_R Output Routing Control 0: PGA_R is not routed to HPROUT 1: PGA_R is routed to HPROUT PGA_R to HPROUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 64: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DAC_R1 to HPROUT Volume Control Register DESCRIPTION DAC_R1 Output Routing Control 0: DAC_R1 is not routed to HPROUT 1: DAC_R1 is routed to HPROUT DAC_R1 to HPROUT Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 65: HPROUT Output Level Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D4 R/W 0000 D3 R/W 0 HPROUT Mute 0: HPROUT is muted 1: HPROUT is not muted D2 R/W 1 HPROUT Power Down Drive Control 0: HPROUT is weakly driven to a common-mode when powered down 1: HPROUT is tri-stated with powered down D1 R 0 HPROUT Volume Control Status 0: All programmed gains to HPROUT have been applied 1: Not all programmed gains to HPROUT have been applied yet D0 R/W 0 HPROUT Power Control 0: HPROUT is not fully powered up 1: HPROUT is fully powered up HPROUT Output Level Control 0000: Output level control = 0-dB 0001: Output level control = 1-dB 0010: Output level control = 2-dB ... 1000: Output level control = 8-dB 1001: Output level control = 9-dB 1010–1111: Reserved. Do not write these sequences to these register bits. Submit Documentation Feedback 65 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 66: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DESCRIPTION LINE2L Output Routing Control 0: LINE2L is not routed to HPRCOM 1: LINE2L is routed to HPRCOM LINE2L to HPRCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 67: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 PGA_L Output Routing Control 0: PGA_L is not routed to HPRCOM 1: PGA_L is routed to HPRCOM PGA_L to HPRCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DAC_L1 Output Routing Control 0: DAC_L1 is not routed to HPRCOM 1: DAC_L1 is routed to HPRCOM DAC_L1 to HPRCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 LINE2R Output Routing Control 0: LINE2R is not routed to HPRCOM 1: LINE2R is routed to HPRCOM LINE2R to HPRCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 66 PGA_R to HPRCOM Volume Control Register DESCRIPTION PGA_R Output Routing Control 0: PGA_R is not routed to HPRCOM 1: PGA_R is routed to HPRCOM PGA_R to HPRCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 71: BIT LINE2R to HPRCOM Volume Control Register DESCRIPTION Page 0 / Register 70: BIT DAC_L1 to HPRCOM Volume Control Register DESCRIPTION Page 0 / Register 69: BIT PGA_L to HPRCOM Volume Control Register DESCRIPTION Page 0 / Register 68: BIT LINE2L to HPRCOM Volume Control Register DAC_R1 to HPRCOM Volume Control Register DESCRIPTION DAC_R1 Output Routing Control 0: DAC_R1 is not routed to HPRCOM 1: DAC_R1 is routed to HPRCOM DAC_R1 to HPRCOM Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 72: HPRCOM Output Level Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D4 R/W 0000 D3 R/W 0 HPRCOM Mute 0: HPRCOM is muted 1: HPRCOM is not muted D2 R/W 1 HPRCOM Power Down Drive Control 0: HPRCOM is weakly driven to a common-mode when powered down 1: HPRCOM is tri-stated with powered down D1 R 0 HPRCOM Volume Control Status 0: All programmed gains to HPRCOM have been applied 1: Not all programmed gains to HPRCOM have been applied yet D0 R/W 0 HPRCOM Power Control 0: HPRCOM is not fully powered up 1: HPRCOM is fully powered up HPRCOM Output Level Control 0000: Output level control = 0-dB 0001: Output level control = 1-dB 0010: Output level control = 2-dB ... 1000: Output level control = 8-dB 1001: Output level control = 9-dB 1010–1111: Reserved. Do not write these sequences to these register bits. Page 0 / Register 73: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DESCRIPTION LINE2L Output Routing Control 0: LINE2L is not routed to MONO_LOP/M 1: LINE2L is routed to MONO_LOP/M LINE2L to MONO_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 74: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 PGA_L Output Routing Control 0: PGA_L is not routed to MONO_LOP/M 1: PGA_L is routed to MONO_LOP/M PGA_L to MONO_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DAC_L1 to MONO_LOP/M Volume Control Register DESCRIPTION DAC_L1 Output Routing Control 0: DAC_L1 is not routed to MONO_LOP/M 1: DAC_L1 is routed to MONO_LOP/M DAC_L1 to MONO_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 76: BIT PGA_L to MONO_LOP/M Volume Control Register DESCRIPTION Page 0 / Register 75: BIT LINE2L to MONO_LOP/M Volume Control Register LINE2R to MONO_LOP/M Volume Control Register DESCRIPTION LINE2R Output Routing Control 0: LINE2R is not routed to MONO_LOP/M 1: LINE2R is routed to MONO_LOP/M LINE2R to MONO_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Submit Documentation Feedback 67 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 77: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DESCRIPTION PGA_R Output Routing Control 0: PGA_R is not routed to MONO_LOP/M 1: PGA_R is routed to MONO_LOP/M PGA_R to MONO_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 78: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 PGA_R to MONO_LOP/M Volume Control Register DAC_R1 to MONO_LOP/M Volume Control Register DESCRIPTION DAC_R1 Output Routing Control 0: DAC_R1 is not routed to MONO_LOP/M 1: DAC_R1 is routed to MONO_LOP/M DAC_R1 to MONO_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 79: MONO_LOP/M Output Level Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D4 R/W 0000 D3 R/W 0 MONO_LOP/M Mute 0: MONO_LOP/M is muted 1: MONO_LOP/M is not muted D2 R/W 0 Reserved. Write only zero to this register bit. D1 R 0 MONO_LOP/M Volume Control Status 0: All programmed gains to MONO_LOP/M have been applied 1: Not all programmed gains to MONO_LOP/M have been applied yet D0 R/W 0 MONO_LOP/M Power Control 0: MONO_LOP/M is not fully powered up 1: MONO_LOP/M is fully powered up MONO_LOP/M Output Level Control 0000: Output level control = 0-dB 0001: Output level control = 1-dB 0010: Output level control = 2-dB ... 1000: Output level control = 8-dB 1001: Output level control = 9-dB 1010–1111: Reserved. Do not write these sequences to these register bits. Page 0 / Register 80: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DESCRIPTION LINE2L Output Routing Control 0: LINE2L is not routed to LEFT_LOP/M 1: LINE2L is routed to LEFT_LOP/M LINE2L to LEFT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 81: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 68 LINE2L to LEFT_LOP/M Volume Control Register PGA_L to LEFT_LOP/M Volume Control Register DESCRIPTION PGA_L Output Routing Control 0: PGA_L is not routed to LEFT_LOP/M 1: PGA_L is routed to LEFT_LOP/M PGA_L to LEFT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 82: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DESCRIPTION DAC_L1 Output Routing Control 0: DAC_L1 is not routed to LEFT_LOP/M 1: DAC_L1 is routed to LEFT_LOP/M DAC_L1 to LEFT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 83: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 LINE2R Output Routing Control 0: LINE2R is not routed to LEFT_LOP/M 1: LINE2R is routed to LEFT_LOP/M LINE2R to LEFT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 PGA_R to LEFT_LOP/M Volume Control Register DESCRIPTION PGA_R Output Routing Control 0: PGA_R is not routed to LEFT_LOP/M 1: PGA_R is routed to LEFT_LOP/M PGA_R to LEFT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 85: BIT LINE2R to LEFT_LOP/M Volume Control Register DESCRIPTION Page 0 / Register 84: BIT DAC_L1 to LEFT_LOP/M Volume Control Register DAC_R1 to LEFT_LOP/M Volume Control Register DESCRIPTION DAC_R1 Output Routing Control 0: DAC_R1 is not routed to LEFT_LOP/M 1: DAC_R1 is routed to LEFT_LOP/M DAC_R1 to LEFT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 86: LEFT_LOP/M Output Level Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D4 R/W 0000 D3 R/W 0 LEFT_LOP/M Mute 0: LEFT_LOP/M is muted 1: LEFT_LOP/M is not muted D2 R/W 0 Reserved. Write only zero to this register bit. D1 R 0 LEFT_LOP/M Volume Control Status 0: All programmed gains to LEFT_LOP/M have been applied 1: Not all programmed gains to LEFT_LOP/M have been applied yet D0 R/W 0 LEFT_LOP/M Power Control 0: LEFT_LOP/M is not fully powered up 1: LEFT_LOP/M is fully powered up LEFT_LOP/M Output Level Control 0000: Output level control = 0-dB 0001: Output level control = 1-dB 0010: Output level control = 2-dB ... 1000: Output level control = 8-dB 1001: Output level control = 9-dB 1010–1111: Reserved. Do not write these sequences to these register bits. Submit Documentation Feedback 69 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 87: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 DESCRIPTION LINE2L Output Routing Control 0: LINE2L is not routed to RIGHT_LOP/M 1: LINE2L is routed to RIGHT_LOP/M LINE2L to RIGHT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 88: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 PGA_L Output Routing Control 0: PGA_L is not routed to RIGHT_LOP/M 1: PGA_L is routed to RIGHT_LOP/M PGA_L to RIGHT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 DAC_L1 to RIGHT_LOP/M Volume Control Register DESCRIPTION DAC_L1 Output Routing Control 0: DAC_L1 is not routed to RIGHT_LOP/M 1: DAC_L1 is routed to RIGHT_LOP/M DAC_L1 to RIGHT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 90: BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 BIT READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 LINE2R Output Routing Control 0: LINE2R is not routed to RIGHT_LOP/M 1: LINE2R is routed to RIGHT_LOP/M LINE2R to RIGHT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 READ/ WRITE RESET VALUE D7 R/W 0 D6-D0 R/W 0000000 PGA_R to RIGHT_LOP/M Volume Control Register DESCRIPTION PGA_R Output Routing Control 0: PGA_R is not routed to RIGHT_LOP/M 1: PGA_R is routed to RIGHT_LOP/M PGA_R to RIGHT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Page 0 / Register 92: BIT LINE2R to RIGHT_LOP/M Volume Control Register DESCRIPTION Page 0 / Register 91: 70 PGA_L to RIGHT_LOP/M Volume Control Register DESCRIPTION Page 0 / Register 89: BIT LINE2L to RIGHT_LOP/M Volume Control Register DAC_R1 to RIGHT_LOP/M Volume Control Register DESCRIPTION DAC_R1 Output Routing Control 0: DAC_R1 is not routed to RIGHT_LOP/M 1: DAC_R1 is routed to RIGHT_LOP/M DAC_R1 to RIGHT_LOP/M Analog Volume Control For 7-bit register setting versus analog gain values, see Table 4 Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 93: RIGHT_LOP/M Output Level Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D4 R/W 0000 D3 R/W 0 RIGHT_LOP/M Mute 0: RIGHT_LOP/M is muted 1: RIGHT_LOP/M is not muted D2 R/W 0 Reserved. Write only zero to this register bit. D1 R 0 RIGHT_LOP/M Volume Control Status 0: All programmed gains to RIGHT_LOP/M have been applied 1: Not all programmed gains to RIGHT_LOP/M have been applied yet D0 R/W 0 RIGHT_LOP/M Power Control 0: RIGHT_LOP/M is not fully powered up 1: RIGHT_LOP/M is fully powered up RIGHT_LOP/M Output Level Control 0000: Output level control = 0-dB 0001: Output level control = 1-dB 0010: Output level control = 2-dB ... 1000: Output level control = 8-dB 1001: Output level control = 9-dB 1010–1111: Reserved. Do not write these sequences to these register bits. Page 0 / Register 94: Module Power Status Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R 0 Left DAC Power Status 0: Left DAC not fully powered up 1: Left DAC fully powered up D6 R 0 Right DAC Power Status 0: Right DAC not fully powered up 1: Right DAC fully powered up D5 R 0 MONO_LOP/M Power Status 0: MONO_LOP/M output driver powered down 1: MONO_LOP/M output driver powered up D4 R 0 LEFT_LOP/M Power Status 0: LEFT_LOP/M output driver powered down 1: LEFT_LOP/M output driver powered up D3 R 0 RIGHT_LOP/M Power Status 0: RIGHT_LOP/M is not fully powered up 1: RIGHT_LOP/M is fully powered up D2 R 0 HPLOUT Driver Power Status 0: HPLOUT Driver is not fully powered up 1: HPLOUT Driver is fully powered up D1 R/W 0 HPROUT Driver Power Status 0: HPROUT Driver is not fully powered up 1: HPROUT Driver is fully powered up D0 R 0 Reserved. Do not write to this register bit. Page 0 / Register 95: Output Driver Short Circuit Detection Status Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R 0 HPLOUT Short Circuit Detection Status 0: No short circuit detected at HPLOUT 1: Short circuit detected at HPLOUT D6 R 0 HPROUT Short Circuit Detection Status 0: No short circuit detected at HPROUT 1: Short circuit detected at HPROUT D5 R 0 HPLCOM Short Circuit Detection Status 0: No short circuit detected at HPLCOM 1: Short circuit detected at HPLCOM Submit Documentation Feedback 71 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 95: Output Driver Short Circuit Detection Status Register (continued) BIT READ/ WRITE RESET VALUE DESCRIPTION D4 R 0 HPRCOM Short Circuit Detection Status 0: No short circuit detected at HPRCOM 1: Short circuit detected at HPRCOM D3 R 0 HPLCOM Power Status 0: HPLCOM is not fully powered up 1: HPLCOM is fully powered up D2 R 0 HPRCOM Power Status 0: HPRCOM is not fully powered up 1: HPRCOM is fully powered up D1-D0 R 00 Reserved. Do not write to these register bits. Page 0 / Register 96: BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R 0 HPLOUT Short Circuit Detection Status 0: No short circuit detected at HPLOUT driver 1: Short circuit detected at HPLOUT driver D6 R 0 HPROUT Short Circuit Detection Status 0: No short circuit detected at HPROUT driver 1: Short circuit detected at HPROUT driver D5 R 0 HPLCOM Short Circuit Detection Status 0: No short circuit detected at HPLCOM driver 1: Short circuit detected at HPLCOM driver D4 R 0 HPRCOM Short Circuit Detection Status 0: No short circuit detected at HPRCOM driver 1: Short circuit detected at HPRCOM driver D3 R 0 Button Press Detection Status 0: No Headset Button Press detected 1: Headset Button Pressed D2 R 0 Headset Detection Status 0: No Headset insertion/removal is detected 1: Headset insertion/removal is detected D1 R 0 Left ADC AGC Noise Gate Status 0: Left ADC Signal Power Greater than Noise Threshold for Left AGC 1: Left ADC Signal Power Lower than Noise Threshold for Left AGC D0 R 0 Right ADC AGC Noise Gate Status 0: Right ADC Signal Power Greater than Noise Threshold for Right AGC 1: Right ADC Signal Power Lower than Noise Threshold for Right AGC Page 0 / Register 97: 72 Sticky Interrupt Flags Register Real-time Interrupt Flags Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R 0 HPLOUT Short Circuit Detection Status 0: No short circuit detected at HPLOUT driver 1: Short circuit detected at HPLOUT driver D6 R 0 HPROUT Short Circuit Detection Status 0: No short circuit detected at HPROUT driver 1: Short circuit detected at HPROUT driver D5 R 0 HPLCOM Short Circuit Detection Status 0: No short circuit detected at HPLCOM driver 1: Short circuit detected at HPLCOM driver D4 R 0 HPRCOM Short Circuit Detection Status 0: No short circuit detected at HPRCOM driver 1: Short circuit detected at HPRCOM driver Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 97: (1) Real-time Interrupt Flags Register (continued) BIT READ/ WRITE RESET VALUE DESCRIPTION D3 R 0 Button Press Detection Status (1) 0: No Headset Button Press detected 1: Headset Button Pressed D2 R 0 Headset Detection Status 0: No Headset is detected 1: Headset is detected D1 R 0 Left ADC AGC Noise Gate Status 0: Left ADC Signal Power Greater than Noise Threshold for Left AGC 1: Left ADC Signal Power Lower than Noise Threshold for Left AGC D0 R 0 Right ADC AGC Noise Gate Status 0: Right ADC Signal Power Greater than Noise Threshold for Right AGC 1: Right ADC Signal Power Lower than Noise Threshold for Right AGC This bit is a sticky bit, cleared only when page 0, register 14 is read. Page 0 / Register 98: GPIO1 Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D4 R/W 0000 D3 R/W 0 GPIO1 Clock Mux Output Control 0: GPIO1 clock mux output = PLL output 1: GPIO1 clock mux output = clock divider mux output D2 R/W 0 GPIO1 Interrupt Duration Control 0: GPIO1 Interrupt occurs as a single active-high pulse of typical duration 2ms. 1: GPIO1 Interrupt occurs as continuous pulses until the Interrupt Flags register (register 96) is read by the host D1 R 0 GPIO1 General Purpose Input Value 0: A logic-low level is input to GPIO1 1: A logic-high level is input to GPIO1 D0 R/W 0 GPIO1 General Purpose Output Value 0: GPIO1 outputs a logic-low level 1: GPIO1 outputs a logic-high level GPIO1 Output Control 0000: GPIO1 is disabled 0001: GPIO1 used for audio serial data bus ADC word clock 0010: GPIO1 output = clock mux output divided by 1 (M=1) 0011: GPIO1 output = clock mux output divided by 2 (M=2) 0100: GPIO1 output = clock mux output divided by 4 (M=4) 0101: GPIO1 output = clock mux output divided by 8 (M=8) 0110: GPIO1 output = short circuit interrupt 0111: GPIO1 output = AGC noise interrupt 1000: GPIO1 = general purpose input 1001: GPIO1 = general purpose output 1010: GPIO1 output = digital microphone modulator clock 1011: GPIO1 = word clock for audio serial data bus (programmable as input or output) 1100: GPIO1 output = hook-switch/button press interrupt (interrupt polarity: active high, typical interrupt duration: button pressed time + clock resolution. Clock resolution depends upon debounce programmability. Typical interrupt delay from button: debounce duration + 0.5ms) 1101: GPIO1 output = jack/headset detection interrupt 1110: GPIO1 output = jack/headset detection interrupt OR button press interrupt 1111: GPIO1 output = jack/headset detection OR button press OR Short Circuit detection OR AGC Noise detection interrupt Submit Documentation Feedback 73 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 99: GPIO2 Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D4 R/W 0000 D3 R/W 0 GPIO2 General Purpose Output Value 0: GPIO1 outputs a logic-low level 1: GPIO1 outputs a logic-high level D2 R 0 GPIO2 General Purpose Input Value 0: A logic-low level is input to GPIO2 1: A logic-high level is input to GPIO2 D1 R/W 0 GPIO2 Interrupt Duration Control 0: GPIO2 Interrupt occurs as a single active-high pulse of typical duration 2ms. 1: GPIO2 Interrupt occurs as continuous pulses until the Interrupt Flags register (register 96) is read by the host D0 R/W 0 Reserved. Write only zero to this register bit. GPIO2 Output Control 0000: GPIO2 is disabled 0001: Reserved. Do not use. 0010: GPIO2 output = jack/headset detect interrupt (interrupt polarity: active high. Typical interrupt duration: 1.75 ms.) 0011: GPIO2 = general purpose input 0100: GPIO2 = general purpose output 0101-0111: GPIO2 input = digital microphone input, data sampled on clock rising and falling edges 1000: GPIO2 = bit clock for audio serial data bus (programmable as input or output) 1001: GPIO2 output = Headset Detect OR Button Press Interrupt 1010: GPIO2 output = Headset Detect OR Button Press OR Short-Circuit Detect OR AGC Noise Detect Interrupt 1011: GPIO2 output = Short Circuit Detect OR AGC Noise Detect Interrupt 1100: GPIO2 output = Headset Detect OR Button Press OR Short-Circuit Detect Interrupt 1101: GPIO2 output = Short Circuit Detect Interrupt 1110: GPIO2 output = AGC Noise Detect Interrupt 1111: GPIO2 output = Button Press / Hookswitch Interrupt Page 0 / Register 100: Additional GPIO Control Register A BIT READ/ WRITE RESET VALUE D7-D6 R/W 00 SDA Pin Control (1) The SDA pin hardware includes pull-down capability only (open-drain NMOS), so an external pull-up resistor is required when using this pin, even in GPIO mode. 00: SDA pin is not used as general purpose I/O 01: SDA pin used as general purpose input 10: SDA pin used as general purpose output 11: Reserved. Do not write this sequence to these register bits. D5 R/W 0 SDA General Purpose Output Control (1) 0: SDA driven to logic-low when used as general purpose output 1: SDA driven to logic-high when used as general purpose output (requires external pull-up resistor) D4 R 0 SDA General Purpose Input Value (1) 0: SDA detects a logic-low when used as general purpose input 1: SDA is detects a logic-high when used as general purpose input D3-D2 R/W 00 SCL Pin Control (1) The SCL pin hardware includes pulldown capability only (open-drain NMOS), so an external pull-up resistor is required when using this pin, even in GPIO mode. 00: SCL pin is not used as general purpose I/O 01: SCL pin used as general purpose input 10: SCL pin used as general purpose output 11: Reserved. Do not write this sequence to these register bits. D1 R/W 0 SCL General Purpose Output Control (1) 0: SCL driven to logic-low when used as general purpose output 1: SCL driven to logic-high when used as general purpose output (requires external pull-up resistor) D0 R 0 SCL General Purpose Input Value (1) 0: SCL detects a logic-low when used as general purpose input 1: SCL detects a logic-high when used as general purpose input (1) 74 DESCRIPTION The control bits in Register 100 are only valid in SPI Mode, when SELECT=1. Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 0 / Register 101: (1) Additional GPIO Control Register B BIT READ/ WRITE RESET VALUE DESCRIPTION D7 R 0 I2C Address Pin #0 Status (1) 0: MFP1 pin = I2C address pin #0 = 0 at reset 1: MFP1 pin = I2C address pin #0 = 1 at reset D6 R 0 I2C Address Pin #1 Status (1) 0: MFP0 pin = I2C address pin #1 = 0 at reset 1: MFP0 pin = I2C address pin #1 = 1 at reset D5 R/W 0 MFP3 Pin General Purpose Input Control (1) 0: MFP3 pin usage as general purpose input is disabled 1: MFP3 pin usage as general purpose input is enabled D4 R/W 0 MFP3 Pin Serial Data Bus Input Control (1) 0: MFP3 pin usage as audio serial data input pin is disabled 1: MFP3 pin usage as audio serial data input pin is enabled D3 R 0 MFP3 General Purpose Input Value (1) 0: MFP3 detects a logic-low when used as general purpose input 1: MFP3 detects a logic-high when used as general purpose input D2 R/W 0 MFP2 General Purpose Output Control (1) 0: MFP2 pin usage as general purpose output is disabled 1: MFP2 pin usage as general purpose output is enabled D1 R/W 0 MFP2 General Purpose Output Control (1) 0: MFP2 pin drives a logic-low when used as a general purpose output 1: MFP2 pin drives a logic-high when used as a general purpose output D0 R/W 0 CODEC_CLKIN Source Selection 0: CODEC_CLKIN uses PLLDIV_OUT 1: CODEC_CLKIN uses CLKDIV_OUT Bits D7-D1 in Register 101 are only valid in I2C control Mode, when SELECT = 0. Page 0 / Register 102: Clock Generation Control Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D6 R/W 00 CLKDIV_IN Source Selection 00: CLKDIV_IN uses MCLK 01: CLKDIV_IN uses GPIO2 10: CLKDIV_IN uses BCLK 11: Reserved. Do not use. D5-D4 R/W 00 PLLCLK_IN Source Selection 00: PLLCLK_IN uses MCLK 01: PLLCLK_IN uses GPIO2 10: PLLCLK _IN uses BCLK 11: Reserved. Do not use. D3-D0 R/W 0010 PLL Clock Divider N Value 0000: N=16 0001: N=17 0010: N=2 0011: N=3 … 1111: N=15 Page 0 / Register 103–127: BIT READ/ WRITE RESET VALUE D7-D0 R 00000000 DESCRIPTION Reserved. Do not write to these registers. Page 1 / Register 0: BIT READ/ WRITE RESET VALUE D7-D1 X 0000000 Reserved Registers Page Select Register DESCRIPTION Reserved, write only zeros to these register bits Submit Documentation Feedback 75 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 1 / Register 0: READ/ WRITE RESET VALUE DESCRIPTION D0 R/W 0 Page Select Bit Writing zero to this bit sets Page-0 as the active page for following register accesses. Writing a one to this bit sets Page-1 as the active page for following register accesses. It is recommended that the user read this register bit back after each write, to ensure that the proper page is being accessed for future register read/writes. This register has the same functionality on page-0 and page-1. Left Channel Audio Effects Filter N0 Coefficient MSB Register (1) Page 1 / Register 1: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x6B (1) DESCRIPTION Left Channel Audio Effects Filter N0 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Note that whenever any coefficient value is changed, the MSB register should be written first, immediately followed by theLSB register. Even if only the MSB or LSB of the value changes, both registers should be written Page 1 / Register 2: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0xE3 Left Channel Audio Effects Filter N0 Coefficient LSB Register DESCRIPTION Left Channel Audio Effects Filter N0 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 3: Left Channel Audio Effects Filter N1 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x96 Left Channel Audio Effects Filter N1 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 4: Left Channel Audio Effects Filter N1 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x66 Left Channel Audio Effects Filter N1 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 5: Left Channel Audio Effects Filter N2 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x67 Left Channel Audio Effects Filter N2 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 6: 76 Page Select Register (continued) BIT Left Channel Audio Effects Filter N2 Coefficient LSB BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x5D Left Channel Audio Effects Filter N2 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 1 / Register 7: Left Channel Audio Effects Filter N3 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x6B Left Channel Audio Effects Filter N3 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 8: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0xE3 Left Channel Audio Effects Filter N3 Coefficient LSB Register DESCRIPTION Left Channel Audio Effects Filter N3 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 9: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x96 Left Channel Audio Effects Filter N4 Coefficient MSB Register DESCRIPTION Left Channel Audio Effects Filter N4 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 10: Left Channel Audio Effects Filter N4 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x66 Left Channel Audio Effects Filter N4 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 11: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x67 Page 1 / Register 12: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x5D Page 1 / Register 13: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x7D Page 1 / Register 14: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x83 Left Channel Audio Effects Filter N5 Coefficient MSB Register DESCRIPTION Left Channel Audio Effects Filter N5 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Left Channel Audio Effects Filter N5 Coefficient LSB Register DESCRIPTION Left Channel Audio Effects Filter N5 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from -32768 to +32767. Left Channel Audio Effects Filter D1 Coefficient MSB Register DESCRIPTION Left Channel Audio Effects Filter D1 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Left Channel Audio Effects Filter D1 Coefficient LSB Register DESCRIPTION Left Channel Audio Effects Filter D1 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Submit Documentation Feedback 77 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 1 / Register 15: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x84 Page 1 / Register 16: DESCRIPTION Left Channel Audio Effects Filter D2 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Left Channel Audio Effects Filter D2 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0xEE Left Channel Audio Effects Filter D2 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 17: Left Channel Audio Effects Filter D4 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x7D Left Channel Audio Effects Filter D4 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 18: Left Channel Audio Effects Filter D4 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x83 Left Channel Audio Effects Filter D4 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 19: Left Channel Audio Effects Filter D5 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x84 Left Channel Audio Effects Filter D5 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 20: Left Channel Audio Effects Filter D5 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0xEE Left Channel Audio Effects Filter D5 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 21: Left Channel De-emphasis Filter N0 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x39 Left Channel De-emphasis Filter N0 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 22: 78 Left Channel Audio Effects Filter D2 Coefficient MSB Register Left Channel De-emphasis Filter N0 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x55 Left Channel De-emphasis Filter N0 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 1 / Register 23: Left Channel De-emphasis Filter N1 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0xF3 Left Channel De-emphasis Filter N1 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 24: Left Channel De-emphasis Filter N1 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x2D Left Channel De-emphasis Filter N1 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 25: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x53 Page 1 / Register 26: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x7E Page 1 / Register 27: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x6B Page 1 / Register 28: Left Channel De-emphasis Filter D1 Coefficient MSB Register DESCRIPTION Left Channel De-emphasis Filter A0 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Left Channel De-emphasis Filter D1 Coefficient LSB Register DESCRIPTION Left Channel De-emphasis Filter A0 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Right Channel Audio Effects Filter N0 Coefficient MSB Register DESCRIPTION Right Channel Audio Effects Filter N0 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Right Channel Audio Effects Filter N0 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0xE3 Right Channel Audio Effects Filter N0 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 29: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x96 Page 1 / Register 30: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x66 Right Channel Audio Effects Filter N1 Coefficient MSB Register DESCRIPTION Right Channel Audio Effects Filter N1 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Right Channel Audio Effects Filter N1 Coefficient LSB Register DESCRIPTION Right Channel Audio Effects Filter N1 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Submit Documentation Feedback 79 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 1 / Register 31: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x67 Page 1 / Register 32: DESCRIPTION Right Channel Audio Effects Filter N2 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Right Channel Audio Effects Filter N2 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x5D Right Channel Audio Effects Filter N2 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 33: Right Channel Audio Effects Filter N3 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x6B Right Channel Audio Effects Filter N3 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 34: Right Channel Audio Effects Filter N3 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0xE3 Right Channel Audio Effects Filter N3 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 35: BIT READ/ WRITE RESET VALUE D7-D0 R/W 0x96 Page 1 / Register 36: Right Channel Audio Effects Filter N4 Coefficient MSB Register DESCRIPTION Right Channel Audio Effects Filter N4 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Right Channel Audio Effects Filter N4 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x66 Right Channel Audio Effects Filter N4 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 37: Right Channel Audio Effects Filter N5 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x67 Right Channel Audio Effects Filter N5 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 38: 80 Right Channel Audio Effects Filter N2 Coefficient MSB Register Right Channel Audio Effects Filter N5 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x5D Right Channel Audio Effects Filter N5 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 1 / Register 39: Right Channel Audio Effects Filter D1 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x7D Right Channel Audio Effects Filter D1 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 40: Right Channel Audio Effects Filter D1 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x83 Right Channel Audio Effects Filter D1 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 41: Right Channel Audio Effects Filter D2 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x84 Right Channel Audio Effects Filter D2 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 42: Right Channel Audio Effects Filter D2 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0xEE Right Channel Audio Effects Filter D2 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 43: Right Channel Audio Effects Filter D4 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x7D Right Channel Audio Effects Filter D4 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 44: Right Channel Audio Effects Filter D4 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x83 Right Channel Audio Effects Filter D4 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 45: Right Channel Audio Effects Filter D5 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x84 Right Channel Audio Effects Filter D5 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 46: Right Channel Audio Effects Filter D5 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0xEE Right Channel Audio Effects Filter D5 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Submit Documentation Feedback 81 TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 1 / Register 47: Right Channel De-emphasis Filter N0 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x39 Right Channel De-emphasis Filter N0 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 48: Right Channel De-emphasis Filter N0 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x55 Right Channel De-emphasis Filter N0 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 49: Right Channel De-emphasis Filter N1 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0xF3 Right Channel De-emphasis Filter N1 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 50: Right Channel De-emphasis Filter N1 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x2D Right Channel De-emphasis Filter N1 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 51: Right Channel De-emphasis Filter D1 Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x53 Right Channel De-emphasis Filter A0 Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 52: Right Channel De-emphasis Filter D1 Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x7E Right Channel De-emphasis Filter A0 Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 53: 3-D Attenuation Coefficient MSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0x7F 3-D Attenuation Coefficient MSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Page 1 / Register 54: 82 3-D Attenuation Coefficient LSB Register BIT READ/ WRITE RESET VALUE DESCRIPTION D7-D0 R/W 0xFF 3-D Attenuation Coefficient LSB The 16-bit integer contained in the MSB and LSB registers for this coefficient are interpreted as a 2’s complement integer, with possible values ranging from –32768 to +32767. Submit Documentation Feedback TLV320AIC33 www.ti.com SLAS480A – JANUARY 2006 – REVISED JULY 2006 Page 1 / Register 55–127: BIT READ/ WRITE RESET VALUE D7-D0 R 0x00 Reserved Registers DESCRIPTION Reserved. Do not write to these registers. Submit Documentation Feedback 83 PACKAGE OPTION ADDENDUM www.ti.com 21-Nov-2006 PACKAGING INFORMATION Orderable Device Status (1) TLV320AIC33IGQE ACTIVE BGA MI CROSTA R JUNI OR GQE 80 360 TBD SNPB Level-2-220C-1 YEAR TLV320AIC33IGQER ACTIVE BGA MI CROSTA R JUNI OR GQE 80 2500 TBD SNPB Level-2-220C-1 YEAR TLV320AIC33IRGZR ACTIVE QFN RGZ 48 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TLV320AIC33IRGZRG4 ACTIVE QFN RGZ 48 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TLV320AIC33IRGZT ACTIVE QFN RGZ 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TLV320AIC33IRGZTG4 ACTIVE QFN RGZ 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TLV320AIC33IZQE ACTIVE BGA MI CROSTA R JUNI OR ZQE 80 360 Pb-Free (RoHS) SNAGCU Level-3-260C-168 HR TLV320AIC33IZQER ACTIVE BGA MI CROSTA R JUNI OR ZQE 80 2500 Pb-Free (RoHS) SNAGCU Level-3-260C-168 HR Package Type Package Drawing Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 21-Nov-2006 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 19-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device TLV320AIC33IGQER TLV320AIC33IRGZR TLV320AIC33IRGZT TLV320AIC33IZQER Package Package Pins Type Drawing BGA MI CROSTA R JUNI OR SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant GQE 80 2500 330.0 12.4 5.3 5.3 1.5 8.0 12.0 Q1 QFN RGZ 48 2500 330.0 16.4 7.3 7.3 1.5 12.0 16.0 Q2 QFN RGZ 48 250 330.0 16.4 7.3 7.3 1.5 12.0 16.0 Q2 ZQE 80 2500 330.0 12.4 5.3 5.3 1.5 8.0 12.0 Q1 BGA MI CROSTA R JUNI OR Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 19-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TLV320AIC33IGQER BGA MICROSTAR JUNIOR GQE 80 2500 340.5 333.0 20.6 TLV320AIC33IRGZR QFN RGZ 48 2500 333.2 345.9 28.6 TLV320AIC33IRGZT QFN RGZ 48 250 333.2 345.9 28.6 TLV320AIC33IZQER BGA MICROSTAR JUNIOR ZQE 80 2500 340.5 333.0 20.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated