TI TPS73633DRBR

TPS736xx
www.ti.com .................................................................................................................................................. SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008
Cap-Free, NMOS, 400mA Low-Dropout Regulator
with Reverse Current Protection
FEATURES
1
• Stable with No Output Capacitor or Any Value
or Type of Capacitor
• Input Voltage Range of 1.7V to 5.5V
• Ultra-Low Dropout Voltage: 75mV typ
• Excellent Load Transient Response—with or
without Optional Output Capacitor
• New NMOS Topology Delivers Low Reverse
Leakage Current
• Low Noise: 30µVRMS typ (10Hz to 100kHz)
• 0.5% Initial Accuracy
• 1% Overall Accuracy Over Line, Load, and
Temperature
• Less Than 1µA max IQ in Shutdown Mode
• Thermal Shutdown and Specified Min/Max
Current Limit Protection
• Available in Multiple Output Voltage Versions
– Fixed Outputs of 1.20V to 5.0V
– Adjustable Output from 1.20V to 5.5V
– Custom Outputs Available
2
APPLICATIONS
•
•
•
•
Portable/Battery-Powered Equipment
Post-Regulation for Switching Supplies
Noise-Sensitive Circuitry such as VCOs
Point of Load Regulation for DSPs, FPGAs,
ASICs, and Microprocessors
DESCRIPTION
The TPS736xx family of low-dropout (LDO) linear
voltage regulators uses a new topology: an NMOS
pass element in a voltage-follower configuration. This
topology is stable using output capacitors with low
ESR, and even allows operation without a capacitor.
It also provides high reverse blockage (low reverse
current) and ground pin current that is nearly constant
over all values of output current.
The TPS736xx uses an advanced BiCMOS process
to yield high precision while delivering very low
dropout voltages and low ground pin current. Current
consumption, when not enabled, is under 1µA and
ideal for portable applications. The extremely low
output noise (30µVRMS with 0.1µF CNR) is ideal for
powering VCOs. These devices are protected by
thermal shutdown and foldback current limit.
DRB PACKAGE
3mmx 3mm SON
(TOP VIEW)
OUT 1
DBV PACKAGE
SOT23
(TOP VIEW)
8 IN
N/C 2
7 N/C
IN
1
NR/FB 3
6 N/C
GND
2
EN
3
GND 4
5 EN
VIN
OUT
4
NR/FB
DCQ PACKAGE
SOT223
(TOP VIEW)
TAB IS GND
6
Optional
5
Optional
IN
VOUT
OUT
1
2
3
4
5
TPS736xx
EN
GND
NR
IN
ON
OFF
GND
EN
OUT NR/FB
Optional
Typical Application Circuit for Fixed-Voltage Versions
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2008, Texas Instruments Incorporated
TPS736xx
SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008 .................................................................................................................................................. www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION (1)
VOUT (2)
PRODUCT
XX is nominal output voltage (for example, 25 = 2.5V, 01 = Adjustable (3)).
YYY is package designator.
Z is package quantity.
TPS736xxyyyz
(1)
(2)
(3)
For the most current specification and package information, refer to the Package Option Addendum located at the end of this datasheet
or see the TI website at www.ti.com.
Most output voltages of 1.25V and 1.3V to 5.0V in 100mV increments are available on a quick-turn basis using innovative factory
EEPROM programming. Minimum order quantities apply; contact factory for details and availability.
For fixed 1.20V operation, tie FB to OUT.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted (1)
PARAMETER
TPS736xx
UNIT
VIN range
–0.3 to 6.0
V
VEN range
–0.3 to 6.0
V
VOUT range
–0.3 to 5.5
V
VNR, VFB range
–0.3 to 6.0
V
Peak output current
Internally limited
Output short-circuit duration
Indefinite
Continuous total power dissipation
See Dissipation Ratings Table
Junction temperature range, TJ
–55 to +150
°C
Storage temperature range
–65 to +150
°C
ESD rating, HBM
2
kV
ESD rating, CDM
500
V
(1)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under the Electrical Characteristics
is not implied. Exposure to absolute maximum rated conditions for extended periods may affect device reliability.
POWER DISSIPATION RATINGS (1)
BOARD
PACKAGE
RθJC
RθJA
DERATING FACTOR
ABOVE TA = 25°C
TA ≤ 25°C
POWER RATING
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
Low-K (2)
DBV
64°C/W
255°C/W
3.9mW/°C
390mW
215mW
155mW
High-K (3)
DBV
64°C/W
180°C/W
5.6mW/°C
560mW
310mW
225mW
Low-K (2)
DCQ
15°C/W
53°C/W
18.9mW/°C
1.89W
1.04W
0.76W
(3)
DCQ
15°C/W
45°C/W
22.2mW/°C
2.22W
1.22W
0.89W
DRB
1.2°C/W
40°C/W
25.0mW/°C
2.50W
1.38W
1.0W
High-K
High-K (3) (4)
(1)
(2)
(3)
(4)
2
See Power Dissipation in the Applications section for more information related to thermal design.
The JEDEC Low-K (1s) board design used to derive this data was a 3inch x 3inch, 2-layer board with 2-ounce copper traces on top of
the board.
The JEDEC High-K (2s2p) board design used to derive this data was a 3inch x 3inch, multilayer board with 1-ounce internal power and
ground planes and 2-ounce copper traces on the top and bottom of the board.
Based on preliminary thermal simulations.
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
TPS736xx
www.ti.com .................................................................................................................................................. SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008
ELECTRICAL CHARACTERISTICS
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(nom) + 0.5V (1), IOUT = 10mA, VEN = 1.7V, and
COUT = 0.1µF, unless otherwise noted. Typical values are at TJ = +25°C.
PARAMETER
TEST CONDITIONS
VIN
Input voltage range (1)
(2)
VFB
Internal reference (TPS73601)
Accuracy (1)
(4)
ΔVOUT%/ΔVIN
MAX
UNIT
5.5
TJ = +25°C
V
1.210
V
VFB
5.5 – VDO
V
+0.5
1.198
Nominal
TJ = +25°C
–0.5
over VIN, IOUT,
and T
VOUT + 0.5V ≤ VIN ≤ 5.5V;
10mA ≤ IOUT ≤ 400mA
–1.0
Line regulation (1)
ΔVOUT%/ΔIOUT Load regulation
0.01
0.002
10mA ≤ IOUT ≤ 400mA
0.0005
IOUT = 400mA
ZO(DO)
Output impedance in dropout
1.7V ≤ VIN ≤ VOUT + VDO
ICL
Output current limit
ISC
Short-circuit current
Reverse leakage current
75
IGND
GND pin current
ISHDN
Shutdown current (IGND)
IFB
FB pin current (TPS73601)
+1.0
VOUT = 0.9 × VOUT(nom)
400
3.6V ≤ VIN ≤ 4.2V, 0°C ≤ TJ ≤ +70°C
500
650
%
%/V
%/mA
200
mV
Ω
0.25
VOUT = 0V
(–IIN)
±0.5
1mA ≤ IOUT ≤ 400mA
Dropout voltage (5)
(VIN = VOUT(nom) – 0.1V)
(6)
1.20
VO(nom) + 0.5V ≤ VIN ≤ 5.5V
VDO
IREV
TYP
1.7
Output voltage range
(TPS73601) (3)
VOUT
MIN
800
mA
800
mA
450
mA
µA
VEN ≤ 0.5V, 0V ≤ VIN ≤ VOUT
0.1
10
IOUT = 10mA (IQ)
400
550
IOUT = 400mA
800
1000
VEN ≤ 0.5V, VOUT ≤ VIN ≤ 5.5,
–40°C ≤ TJ ≤ +100°C
0.02
1
µA
0.1
0.3
µA
PSRR
Power-supply rejection ratio
(ripple rejection)
f = 100Hz, IOUT = 400mA
VN
Output noise voltage
BW = 10Hz – 100KHz
COUT = 10µF, No CNR
27 × VOUT
COUT = 10µF, CNR = 0.01µF
8.5 × VOUT
tSTR
Startup time
VEN(HI)
EN pin high (enabled)
1.7
VIN
V
VEN(LO)
EN pin low (shutdown)
0
0.5
V
IEN(HI)
EN pin current (enabled)
0.1
µA
TSD
Thermal shutdown temperature
TJ
Operating junction temperature
(1)
(2)
(3)
(4)
(5)
(6)
58
f = 10KHz, IOUT = 400mA
37
µA
VOUT = 3V, RL = 30Ω COUT = 1µF,
CNR = 0.01µF
dB
µVRMS
µs
600
VEN = 5.5V
0.02
Shutdown, temperature increasing
+160
Reset, temperature decreasing
+140
–40
°C
+125
°C
Minimum VIN = VOUT + VDO or 1.7V, whichever is greater.
For VOUT(nom) < 1.6V, when VIN ≤ 1.6V, the output will lock to VIN and may result in a damaging over-voltage level on the output. To
avoid this situation, disable the device before powering down the VIN.
TPS73601 is tested at VOUT = 2.5V.
Tolerance of external resistors not included in this specification.
VDO is not measured for fixed output versions with VOUT(nom) < 1.8V.
Fixed-voltage versions only; refer to Applications section for more information.
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
3
TPS736xx
SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008 .................................................................................................................................................. www.ti.com
FUNCTIONAL BLOCK DIAGRAMS
IN
4MHz
Charge Pump
EN
Thermal
Protection
Ref
Servo
27kΩ
Bandgap
Error
Amp
Current
Limit
OUT
8kΩ
GND
R1
R1 + R2 = 80kΩ
R2
NR
Figure 1. Fixed Voltage Version
IN
Table 1. Standard 1%
Resistor Values for
Common Output Voltages
VO
4MHz
Charge Pump
EN
Thermal
Protection
Ref
Servo
27kΩ
Bandgap
Error
Amp
GND
8kΩ
R2
1.2V
Short
Open
1.5V
23.2kΩ
95.3kΩ
1.8V
28.0kΩ
56.2kΩ
2.5V
39.2kΩ
36.5kΩ
2.8V
44.2kΩ
33.2kΩ
3.0V
46.4kΩ
30.9kΩ
3.3V
52.3kΩ
30.1kΩ
NOTE: VOUT = (R1 + R2)/R2 × 1.204;
R1R2 ≅ 19kΩ for best
accuracy.
OUT
Current
Limit
R1
80kΩ
R1
FB
R2
Figure 2. Adjustable Voltage Version
4
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
TPS736xx
www.ti.com .................................................................................................................................................. SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008
PIN CONFIGURATIONS
IN
1
GND
2
EN
3
DRB PACKAGE
3mm x 3mm SON
(TOP VIEW)
DCQ PACKAGE
SOT223
(TOP VIEW)
DBV PACKAGE
SOT23
(TOP VIEW)
5
4
TAB IS GND
6
OUT
NR/FB
1
IN
2
3
4
OUT
1
8
IN
N/C
2
7
N/C
NR/FB
3
6
N/C
GND
4
5
EN
5
GND
EN
OUT
NR/FB
PIN DESCRIPTIONS
NAME
SOT23
(DBV)
PIN NO.
SOT223
(DCQ)
PIN NO.
3x3 SON
(DRB)
PIN NO.
IN
1
1
8
GND
2
3, 6
4, Pad
EN
3
5
5
Driving the enable pin (EN) high turns on the regulator. Driving this pin low puts the
regulator into shutdown mode. Refer to the Shutdown section under Applications
Information for more details. EN can be connected to IN if not used.
NR
4
4
3
Fixed voltage versions only—connecting an external capacitor to this pin bypasses
noise generated by the internal bandgap, reducing output noise to very low levels.
FB
4
4
3
Adjustable voltage version only—this is the input to the control loop error amplifier,
and is used to set the output voltage of the device.
OUT
5
2
1
Output of the Regulator. There are no output capacitor requirements for stability.
DESCRIPTION
Input supply
Ground
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
5
TPS736xx
SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008 .................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS
For all voltage versions, at TJ = +25°C, VIN = VOUT(nom) + 0.5V, IOUT = 10mA, VEN = 1.7V, and COUT = 0.1µF, unless otherwise
noted.
LOAD REGULATION
LINE REGULATION
0.20
0.5
Referred to IOUT = 10mA
−40_C
+25_C
+125_ C
Change in VOUT (%)
0.3
0.2
0.1
0
−0.1
−0.2
−0.3
Referred to VIN = VOUT + 0.5V at IOUT = 10mA
0.15
Change in VOUT (%)
0.4
0.10
0
−0.05
−40_ C
−0.10
−0.15
−0.4
−0.20
−0.5
0
50
100
150
200
250
300
350
0
400
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
VIN − VOUT (V)
IOUT (mA)
Figure 3.
Figure 4.
DROPOUT VOLTAGE vs OUTPUT CURRENT
DROPOUT VOLTAGE vs TEMPERATURE
100
100
TPS73625DBV
+125_ C
80
80
60
VDO (mV)
VDO (mV)
+25_ C
+125_C
0.05
+25_ C
40
−40_C
20
50
100
150
200
250
300
60
40
20
0
0
TPS73625DBV
I OUT = 400mA
350
0
−50
400
−25
IOUT (mA)
0
25
50
75
100
125
Temperature (_ C)
Figure 5.
Figure 6.
OUTPUT VOLTAGE ACCURACY HISTOGRAM
OUTPUT VOLTAGE DRIFT HISTOGRAM
30
18
IOUT = 10mA
16
25
IOUT = 10mA
All Voltage Versions
Percent of Units (%)
Percent of Units (%)
14
20
15
10
12
10
8
6
4
5
2
0
6
−1.0
−0.9
−0.8
−0.7
−0.6
−0.5
−0.4
−0.3
−0.2
−0.1
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
−100
−90
−80
−70
−60
−50
−40
−30
−20
−10
0
10
20
30
40
50
60
70
80
90
100
0
VOUT Error (%)
Worst Case dVOUT/dT (ppm/_C)
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
TPS736xx
www.ti.com .................................................................................................................................................. SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008
TYPICAL CHARACTERISTICS (continued)
For all voltage versions, at TJ = +25°C, VIN = VOUT(nom) + 0.5V, IOUT = 10mA, VEN = 1.7V, and COUT = 0.1µF, unless otherwise
noted.
GROUND PIN CURRENT vs OUTPUT CURRENT
GROUND PIN CURRENT vs TEMPERATURE
900
900
800
800
700
700
600
600
I GND (µA)
1000
IGND (µA)
1000
500
400
300
500
400
300
VIN = 5.5V
VIN = 4V
VIN = 2V
200
100
0
100
200
300
VIN = 5.5V
VIN = 3V
VIN = 2V
200
100
0
0
−50
400
−25
0
25
50
75
IOUT (mA)
Temperature (_C)
Figure 9.
Figure 10.
GROUND PIN CURRENT in SHUTDOWN
vs TEMPERATURE
CURRENT LIMIT vs VOUT
(FOLDBACK)
1
100
125
3.0
3.5
800
VENABLE = 0.5V
VIN = VO + 0.5V
700
Current Limit (mA)
IGND (µA)
IOUT = 400mA
0.1
ICL
600
500
ISC
400
300
200
100
TPS73633
0.01
−50
0
−25
0
25
50
75
100
125
0
1.0
1.5
2.0
VOUT (V)
Figure 11.
Figure 12.
CURRENT LIMIT vs VIN
2.5
CURRENT LIMIT vs TEMPERATURE
800
800
750
750
700
700
Current Limit (mA)
Current Limit (mA)
0.5
Temperature (_C)
650
600
550
500
450
650
600
550
500
450
400
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
400
−50
−25
0
25
50
VIN (V)
Temperature (_C)
Figure 13.
Figure 14.
75
100
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
125
7
TPS736xx
SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008 .................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS (continued)
For all voltage versions, at TJ = +25°C, VIN = VOUT(nom) + 0.5V, IOUT = 10mA, VEN = 1.7V, and COUT = 0.1µF, unless otherwise
noted.
PSRR (RIPPLE REJECTION) vs FREQUENCY
PSRR (RIPPLE REJECTION) vs VIN – VOUT
90
40
IOUT = 100mA
COUT = Any
Ripple Rejection (dB)
70
IOUT = 1mA
COUT = 1µF
35
30
IOUT = 1mA
COUT = 10µF
60
50
IO = 100mA
CO = 1µF
IOUT = 1mA
C OUT = Any
40
25
PSRR (dB)
80
20
15
30
20
IOUT = Any
COUT = 0µF
10
VIN = VOUT + 1V
0
10
100
1k
10k
Frequency = 10kHz
COUT = 10mF
VOUT = 2.5V
IOUT = 100mA
10
I OUT = 100mA
COUT = 10µF
5
0
100k
1M
0
10M
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
Frequency (Hz)
VIN - VOUT (V)
Figure 15.
Figure 16.
NOISE SPECTRAL DENSITY
CNR = 0µF
NOISE SPECTRAL DENSITY
CNR = 0.01µF
1
1.8
2.0
1
COUT = 0µF
0.1
COUT = 10µF
eN (µV/√Hz)
eN (µV/√Hz)
C OUT = 1µF
COUT = 1µF
0.1
COUT = 0µF
COUT = 10µF
IOUT = 150mA
IOUT = 150mA
0.01
0.01
10
100
1k
10k
100k
10
100
1k
Frequency (Hz)
Frequency (Hz)
Figure 17.
Figure 18.
RMS NOISE VOLTAGE vs COUT
10k
100k
RMS NOISE VOLTAGE vs CNR
60
140
50
120
VOUT = 5.0V
VOUT = 5.0V
100
30
VN (RMS)
VN (RMS)
40
VOUT = 3.3V
80
VOUT = 3.3V
60
20
40
VOUT = 1.5V
10
0
0.1
8
20
CNR = 0.01µF
10Hz < Frequency < 100kHz
0
1
10
VOUT = 1.5V
COUT = 0µF
10Hz < Frequency < 100kHz
1p
10p
100p
COUT (µF)
CNR (F)
Figure 19.
Figure 20.
Submit Documentation Feedback
1n
10n
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
TPS736xx
www.ti.com .................................................................................................................................................. SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008
TYPICAL CHARACTERISTICS (continued)
For all voltage versions, at TJ = +25°C, VIN = VOUT(nom) + 0.5V, IOUT = 10mA, VEN = 1.7V, and COUT = 0.1µF, unless otherwise
noted.
TPS73633
LOAD TRANSIENT RESPONSE
VIN = 3.8V
TPS73633
LINE TRANSIENT RESPONSE
COUT = 0µF
100mV/tick
IOUT = 400mA
VOUT
COUT = 0µF
50mV/div
COUT = 1µF
50mV/tick
COUT = 10µF
20mV/tick
VOUT
VOUT
VOUT
COUT = 100µF
50mV/div
VOUT
dVIN
5.5V
400mA
IOUT
50mA/tick
10mA
4.5V
1V/div
VIN
10µs/div
10µs/div
Figure 21.
Figure 22.
TPS73633
TURN-ON RESPONSE
TPS73633
TURN-OFF RESPONSE
RL = 1kΩ
CO UT = 0µF
R L = 20Ω
C OUT = 10µF
VOUT
RL = 20Ω
COUT = 1µF
1V/div
= 0.5V/µs
dt
R L = 20Ω
C OUT = 1µF
1V/div
R L = 1kΩ
C OUT = 0µF
RL = 20Ω
COUT = 10µF
VOUT
2V
2V
VEN
1V/div
1V/div
0V
0V
VEN
100µs/div
100µs/div
Figure 23.
Figure 24.
TPS73633
POWER UP / POWER DOWN
IENABLE vs TEMPERATURE
10
6
5
4
VIN
VOUT
IENABLE (nA)
Volts
3
2
1
1
0.1
0
−1
−2
50ms/div
0.01
−50
−25
0
25
50
75
100
125
Temperature (_ C)
Figure 25.
Figure 26.
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
9
TPS736xx
SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008 .................................................................................................................................................. www.ti.com
TYPICAL CHARACTERISTICS (continued)
For all voltage versions, at TJ = +25°C, VIN = VOUT(nom) + 0.5V, IOUT = 10mA, VEN = 1.7V, and COUT = 0.1µF, unless otherwise
noted.
TPS73601
IFB vs TEMPERATURE
60
160
55
140
50
120
45
100
IFB (nA)
VN (rms)
TPS73601
RMS NOISE VOLTAGE vs CFB
40
60
35
30
25
80
VOUT = 2.5V
COUT = 0µF
R1 = 39.2kΩ
10Hz < Frequency < 100kHz
20
10p
100p
40
20
1n
10n
0
−50
−25
0
25
50
75
100
CFB (F)
Temperature (_C)
Figure 27.
Figure 28.
TPS73601
LOAD TRANSIENT, ADJUSTABLE VERSION
TPS73601
LINE TRANSIENT, ADJUSTABLE VERSION
CFB = 10nF
R1 = 39.2kΩ
COUT = 0µF
200mV/div
VOUT
COUT = 0µF
100mV/div
COUT = 10µF
100mV/div
COUT = 10µF
200mV/div
125
VOUT = 2.5V
CFB = 10nF
VOUT
VOUT
VOUT
4.5V
400mA
3.5V
VIN
10mA
IOUT
5µs/div
25µs/div
Figure 29.
10
Figure 30.
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
TPS736xx
www.ti.com .................................................................................................................................................. SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008
APPLICATION INFORMATION
The TPS736xx belongs to a family of new generation
LDO regulators that use an NMOS pass transistor to
achieve ultra-low-dropout performance, reverse
current blockage, and freedom from output capacitor
constraints. These features, combined with low noise
and an enable input, make the TPS736xx ideal for
portable applications. This regulator family offers a
wide selection of fixed output voltage versions and an
adjustable output version. All versions have thermal
and over-current protection, including foldback
current limit.
Figure 31 shows the basic circuit connections for the
fixed voltage models. Figure 32 gives the connections
for the adjustable output version (TPS73601).
Optional input capacitor.
May improve source
impedance, noise, or PSRR.
VIN
Optional output capacitor.
May improve load transient,
noise, or PSRR.
IN
VOUT
OUT
TPS736xx
EN
GND
NR
ON
OFF
Optional bypass
capacitor to reduce
output noise.
Figure 31. Typical Application Circuit for
Fixed-Voltage Versions
Optional output capacitor.
May improve load transient,
noise, or PSRR.
Optional input capacitor.
May improve source
impedance, noise, or PSRR.
VIN
IN
TPS73601
EN
OFF
VOUT
OUT
GND
R1
CFB
FB
ON
R2
VOUT =
(R1 + R2)
R2
x 1.204
Optional capacitor
reduces output noise
and improves
transient response.
For best accuracy, make the parallel combination of
R1 and R2 approximately euqal to 19kΩ. This 19kΩ,
in addition to the internal 8kΩ resistor, presents the
same impedance to the error amp as the 27kΩ
bandgap reference output. This impedance helps
compensate for leakages into the error amp
terminals.
INPUT AND OUTPUT CAPACITOR
REQUIREMENTS
Although an input capacitor is not required for
stability, it is good analog design practice to connect
a 0.1µF to 1µF low ESR capacitor across the input
supply near the regulator. This counteracts reactive
input sources and improves transient response, noise
rejection, and ripple rejection. A higher-value
capacitor may be necessary if large, fast rise-time
load transients are anticipated or the device is
located several inches from the power source.
The TPS736xx does not require an output capacitor
for stability and has maximum phase margin with no
capacitor. It is designed to be stable for all available
types and values of capacitors. In applications where
multiple low ESR capacitors are in parallel, ringing
may occur when the product of COUT and total ESR
drops below 50nΩF. Total ESR includes all parasitic
resistances, including capacitor ESR and board,
socket, and solder joint resistance. In most
applications, the sum of capacitor ESR and trace
resistance will meet this requirement.
OUTPUT NOISE
A precision band-gap reference is used to generate
the internal reference voltage, VREF. This reference is
the dominant noise source within the TPS736xx and
it generates approximately 32µVRMS (10Hz to
100kHz) at the reference output (NR). The regulator
control loop gains up the reference noise with the
same gain as the reference voltage, so that the noise
voltage of the regulator is approximately given by:
(R1 ) R2)
+ 32mVRMS
R2
V N + 32mVRMS
Figure 32. Typical Application Circuit for
Adjustable-Voltage Version
R1 and R2 can be calculated for any output voltage
using the formula shown in Figure 32. Sample
resistor values for common output voltages are
shown in Figure 2.
VOUT
VREF
(1)
Since the value of VREF is 1.2V, this relationship
reduces to:
mV RMS
V N(mVRMS) + 27
V OUT(V)
V
(2)
ǒ
Ǔ
for the case of no CNR.
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
11
TPS736xx
SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008 .................................................................................................................................................. www.ti.com
An internal 27kΩ resistor in series with the noise
reduction pin (NR) forms a low-pass filter for the
voltage reference when an external noise reduction
capacitor, CNR, is connected from NR to ground. For
CNR = 10nF, the total noise in the 10Hz to 100kHz
bandwidth is reduced by a factor of ~3.2, giving the
approximate relationship:
mV RMS
V N(mVRMS) + 8.5
V OUT(V)
V
(3)
When shutdown capability is not required, EN can be
connected to VIN. However, the pass gate may not be
discharged using this configuration, and the pass
transistor may be left on (enhanced) for a significant
time after VIN has been removed. This scenario can
result in reverse current flow (if the IN pin is low
impedance) and faster ramp times upon power-up. In
addition, for VIN ramp times slower than a few
milliseconds, the output may overshoot upon
power-up.
for CNR = 10nF.
DROPOUT VOLTAGE
ǒ
Ǔ
This noise reduction effect is shown as RMS Noise
Voltage vs CNR in the Typical Characteristics section.
The TPS73601 adjustable version does not have the
NR pin available. However, connecting a feedback
capacitor, CFB, from the output to the feedback pin
(FB) reduces output noise and improves load
transient performance.
The TPS736xx uses an internal charge pump to
develop an internal supply voltage sufficient to drive
the gate of the NMOS pass element above VOUT. The
charge pump generates ~250µV of switching noise at
~4MHz; however, charge-pump noise contribution is
negligible at the output of the regulator for most
values of IOUT and COUT.
BOARD LAYOUT RECOMMENDATION TO
IMPROVE PSRR AND NOISE PERFORMANCE
To improve ac performance such as PSRR, output
noise, and transient response, it is recommended that
the board be designed with separate ground planes
for VIN and VOUT, with each ground plane connected
only at the GND pin of the device. In addition, the
ground connection for the bypass capacitor should
connect directly to the GND pin of the device.
The TPS736xx uses an NMOS pass transistor to
achieve extremely low dropout. When (VIN – VOUT) is
less than the dropout voltage (VDO), the NMOS pass
device is in its linear region of operation and the
input-to-output resistance is the RDS-ON of the NMOS
pass element.
For large step changes in load current, the TPS736xx
requires a larger voltage drop from VIN to VOUT to
avoid degraded transient response. The boundary of
this transient dropout region is approximately twice
the dc dropout. Values of VIN – VOUT above this line
ensure normal transient response.
Operating in the transient dropout region can cause
an increase in recovery time. The time required to
recover from a load transient is a function of the
magnitude of the change in load current rate, the rate
of change in load current, and the available
headroom (VIN to VOUT voltage drop). Under
worst-case conditions [full-scale instantaneous load
change with (VIN – VOUT) close to dc dropout levels],
the TPS736xx can take a couple of hundred
microseconds to return to the specified regulation
accuracy.
TRANSIENT RESPONSE
INTERNAL CURRENT LIMIT
The TPS736xx internal current limit helps protect the
regulator during fault conditions. Foldback current
limit helps to protect the regulator from damage
during output short-circuit conditions by reducing
current limit when VOUT drops below 0.5V. See
Figure 12 in the Typical Characteristics section.
ENABLE PIN AND SHUTDOWN
The enable pin (EN) is active high and is compatible
with standard TTL-CMOS levels. A VEN below 0.5V
(max) turns the regulator off and drops the GND pin
current to approximately 10nA. When EN is used to
shutdown the regulator, all charge is removed from
the pass transistor gate, and the output ramps back
up to a regulated VOUT (see Figure 23).
12
The low open-loop output impedance provided by the
NMOS pass element in a voltage follower
configuration allows operation without an output
capacitor for many applications. As with any
regulator, the addition of a capacitor (nominal value
1µF) from the OUT pin to ground will reduce
undershoot magnitude but increase its duration. In
the adjustable version, the addition of a capacitor,
CFB, from the OUT pin to the FB pin will also improve
the transient response.
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
TPS736xx
www.ti.com .................................................................................................................................................. SBVS038R – SEPTEMBER 2003 – REVISED MAY 2008
The TPS736xx does not have active pull-down when
the output is over-voltage. This allows applications
that connect higher voltage sources, such as
alternate power supplies, to the output. This also
results in an output overshoot of several percent if
load current quickly drops to zero when a capacitor is
connected to the output. The duration of overshoot
can be reduced by adding a load resistor. The
overshoot decays at a rate determined by output
capacitor COUT and the internal/external load
resistance. The rate of decay is given by:
(Fixed Voltage Version)
dVńdt +
C OUT
VOUT
80kW ø R LOAD
(4)
(Adjustable Voltage Version)
dVńdt +
C OUT
V OUT
80kW ø (R 1 ) R 2) ø R LOAD
(5)
REVERSE CURRENT
The NMOS pass element of the TPS736xx provides
inherent protection against current flow from the
output of the regulator to the input when the gate of
the pass device is pulled low. To ensure that all
charge is removed from the gate of the pass element,
the EN pin must be driven low before the input
voltage is removed. If this is not done, the pass
element may be left on due to stored charge on the
gate.
After the EN pin is driven low, no bias voltage is
needed on any pin for reverse current blocking. Note
that reverse current is specified as the current flowing
out of the IN pin due to voltage applied on the OUT
pin. There will be additional current flowing into the
OUT pin due to the 80kΩ internal resistor divider to
ground (see Figure 1 and Figure 2).
For the TPS73601, reverse current may flow when
VFB is more than 1.0V above VIN.
THERMAL PROTECTION
Any tendency to activate the thermal protection circuit
indicates excessive power dissipation or an
inadequate heat sink. For reliable operation, junction
temperature should be limited to +125°C maximum.
To estimate the margin of safety in a complete design
(including heat sink), increase the ambient
temperature until the thermal protection is triggered;
use worst-case loads and signal conditions. For good
reliability, thermal protection should trigger at least
+35°C above the maximum expected ambient
condition of your application. This produces a
worst-case junction temperature of +125°C at the
highest
expected
ambient
temperature
and
worst-case load.
The internal protection circuitry of the TPS736xx has
been designed to protect against overload conditions.
It was not intended to replace proper heat sinking.
Continuously running the TPS736xx into thermal
shutdown degrades device reliability.
POWER DISSIPATION
The ability to remove heat from the die is different for
each
package
type,
presenting
different
considerations in the PCB layout. The PCB area
around the device that is free of other components
moves the heat from the device to the ambient air.
Performance data for JEDEC low- and high-K boards
are shown in the Power Dissipation Ratings table.
Using heavier copper will increase the effectiveness
in removing heat from the device. The addition of
plated through-holes to heat-dissipating layers will
also improve the heat-sink effectiveness.
Power dissipation depends on input voltage and load
conditions. Power dissipation (PD) is equal to the
product of the output current times the voltage drop
across the output pass element (VIN to VOUT):
P D + (VIN * VOUT)
I OUT
(6)
Power dissipation can be minimized by using the
lowest possible input voltage necessary to assure the
required output voltage.
PACKAGE MOUNTING
Thermal protection disables the output when the
junction temperature rises to approximately +160°C,
allowing the device to cool. When the junction
temperature cools to approximately +140°C, the
output circuitry is again enabled. Depending on power
dissipation, thermal resistance, and ambient
temperature, the thermal protection circuit may cycle
on and off. This limits the dissipation of the regulator,
protecting it from damage due to overheating.
Solder pad footprint recommendations for the
TPS736xx are presented in Application Bulletin
Solder Pad Recommendations for Surface-Mount
Devices (SBFA015), available from the Texas
Instruments web site at www.ti.com.
Submit Documentation Feedback
Copyright © 2003–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS736xx
13
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS73601DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73601DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73601DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73601DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73601DCQ
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73601DCQG4
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73601DCQR
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73601DCQRG4
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73601DRBR
ACTIVE
SON
DRB
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73601DRBRG4
ACTIVE
SON
DRB
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73601DRBT
ACTIVE
SON
DRB
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73601DRBTG4
ACTIVE
SON
DRB
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS736125DRBR
ACTIVE
SON
DRB
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS736125DRBRG4
ACTIVE
SON
DRB
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS736125DRBT
ACTIVE
SON
DRB
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS736125DRBTG4
ACTIVE
SON
DRB
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73615DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73615DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73615DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73615DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73615DCQ
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73615DCQG4
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73615DCQR
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73615DCQRG4
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73615DRBR
ACTIVE
SON
DRB
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Addendum-Page 1
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2008
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS73615DRBRG4
ACTIVE
SON
DRB
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73615DRBT
ACTIVE
SON
DRB
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73615DRBTG4
ACTIVE
SON
DRB
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73618DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73618DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73618DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73618DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73618DCQ
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73618DCQG4
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73618DCQR
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73618DCQRG4
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73619DRBR
ACTIVE
SON
DRB
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73619DRBRG4
ACTIVE
SON
DRB
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73619DRBT
ACTIVE
SON
DRB
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73619DRBTG4
ACTIVE
SON
DRB
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73625DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73625DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73625DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73625DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73625DCQ
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73625DCQG4
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73625DCQR
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73625DCQRG4
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73630DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73630DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73630DBVT
ACTIVE
SOT-23
DBV
5
250
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 2
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2008
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TPS73630DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73630DCQ
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73630DCQG4
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73630DCQR
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73630DCQRG4
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73632DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73632DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73632DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73632DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73633DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73633DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73633DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73633DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TPS73633DCQ
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73633DCQG4
ACTIVE
SOT-223
DCQ
6
78
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73633DCQR
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73633DCQRG4
ACTIVE
SOT-223
DCQ
6
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73633DRBR
ACTIVE
SON
DRB
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73633DRBRG4
ACTIVE
SON
DRB
8
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73633DRBT
ACTIVE
SON
DRB
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
TPS73633DRBTG4
ACTIVE
SON
DRB
8
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
Lead/Ball Finish
MSL Peak Temp (3)
TPS73643DBVR
ACTIVE
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
TPS73643DBVRG4
ACTIVE
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
TPS73643DBVT
ACTIVE
SOT-23
DBV
5
250
TBD
Call TI
Call TI
TPS73643DBVTG4
ACTIVE
SOT-23
DBV
5
250
TBD
Call TI
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jul-2008
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Jul-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
TPS73601DBVR
Package Package Pins
Type Drawing
SPQ
SOT-23
3000
179.0
DBV
5
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
8.4
3.2
3.2
1.4
4.0
W
Pin1
(mm) Quadrant
8.0
Q3
TPS73601DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73601DCQR
SOT-223
DCQ
6
2500
330.0
12.4
6.8
7.3
1.88
8.0
12.0
Q3
TPS73601DRBR
SON
DRB
8
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS73601DRBR
SON
DRB
8
3000
330.0
12.4
3.3
3.3
1.0
8.0
12.0
Q2
TPS73601DRBT
SON
DRB
8
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS73601DRBT
SON
DRB
8
250
180.0
12.4
3.3
3.3
1.0
8.0
12.0
Q2
TPS736125DRBR
SON
DRB
8
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS736125DRBT
SON
DRB
8
250
330.0
12.4
3.3
3.3
1.0
8.0
12.0
Q2
TPS736125DRBT
SON
DRB
8
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS73615DBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73615DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73615DCQR
SOT-223
DCQ
6
2500
330.0
12.4
6.8
7.3
1.88
8.0
12.0
Q3
TPS73615DRBR
SON
DRB
8
3000
330.0
12.4
3.3
3.3
1.0
8.0
12.0
Q2
TPS73615DRBR
SON
DRB
8
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS73615DRBT
SON
DRB
8
250
180.0
12.4
3.3
3.3
1.0
8.0
12.0
Q2
TPS73615DRBT
SON
DRB
8
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS73618DBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
29-Jul-2008
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPS73618DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73618DCQR
SOT-223
DCQ
6
2500
330.0
12.4
6.8
7.3
1.88
8.0
12.0
Q3
TPS73619DRBR
SON
DRB
8
3000
330.0
12.4
3.3
3.3
1.0
8.0
12.0
Q2
TPS73619DRBT
SON
DRB
8
250
180.0
12.4
3.3
3.3
1.0
8.0
12.0
Q2
TPS73625DBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73625DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73625DCQR
SOT-223
DCQ
6
2500
330.0
12.4
6.8
7.3
1.88
8.0
12.0
Q3
TPS73630DBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73630DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73630DCQR
SOT-223
DCQ
6
2500
330.0
12.4
6.8
7.3
1.88
8.0
12.0
Q3
TPS73632DBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73632DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73633DBVR
SOT-23
DBV
5
3000
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73633DBVT
SOT-23
DBV
5
250
179.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
TPS73633DCQR
SOT-223
DCQ
6
2500
330.0
12.4
6.8
7.3
1.88
8.0
12.0
Q3
TPS73633DRBR
SON
DRB
8
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS73633DRBR
SON
DRB
8
3000
330.0
12.4
3.3
3.3
1.0
8.0
12.0
Q2
TPS73633DRBT
SON
DRB
8
250
180.0
12.4
3.3
3.3
1.0
8.0
12.0
Q2
TPS73633DRBT
SON
DRB
8
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
29-Jul-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS73601DBVR
SOT-23
DBV
5
3000
195.0
200.0
45.0
TPS73601DBVT
SOT-23
DBV
5
250
195.0
200.0
45.0
TPS73601DCQR
SOT-223
DCQ
6
2500
358.0
335.0
35.0
TPS73601DRBR
SON
DRB
8
3000
346.0
346.0
29.0
TPS73601DRBR
SON
DRB
8
3000
370.0
355.0
55.0
TPS73601DRBT
SON
DRB
8
250
190.5
212.7
31.8
TPS73601DRBT
SON
DRB
8
250
220.0
205.0
50.0
TPS736125DRBR
SON
DRB
8
3000
346.0
346.0
29.0
TPS736125DRBT
SON
DRB
8
250
370.0
355.0
55.0
TPS736125DRBT
SON
DRB
8
250
190.5
212.7
31.8
TPS73615DBVR
SOT-23
DBV
5
3000
195.0
200.0
45.0
TPS73615DBVT
SOT-23
DBV
5
250
195.0
200.0
45.0
TPS73615DCQR
SOT-223
DCQ
6
2500
358.0
335.0
35.0
TPS73615DRBR
SON
DRB
8
3000
370.0
355.0
55.0
TPS73615DRBR
SON
DRB
8
3000
346.0
346.0
29.0
TPS73615DRBT
SON
DRB
8
250
220.0
205.0
50.0
TPS73615DRBT
SON
DRB
8
250
190.5
212.7
31.8
TPS73618DBVR
SOT-23
DBV
5
3000
195.0
200.0
45.0
TPS73618DBVT
SOT-23
DBV
5
250
195.0
200.0
45.0
TPS73618DCQR
SOT-223
DCQ
6
2500
358.0
335.0
35.0
TPS73619DRBR
SON
DRB
8
3000
370.0
355.0
55.0
TPS73619DRBT
SON
DRB
8
250
220.0
205.0
50.0
TPS73625DBVR
SOT-23
DBV
5
3000
195.0
200.0
45.0
TPS73625DBVT
SOT-23
DBV
5
250
195.0
200.0
45.0
TPS73625DCQR
SOT-223
DCQ
6
2500
358.0
335.0
35.0
TPS73630DBVR
SOT-23
DBV
5
3000
195.0
200.0
45.0
TPS73630DBVT
SOT-23
DBV
5
250
195.0
200.0
45.0
TPS73630DCQR
SOT-223
DCQ
6
2500
358.0
335.0
35.0
TPS73632DBVR
SOT-23
DBV
5
3000
195.0
200.0
45.0
TPS73632DBVT
SOT-23
DBV
5
250
195.0
200.0
45.0
TPS73633DBVR
SOT-23
DBV
5
3000
195.0
200.0
45.0
TPS73633DBVT
SOT-23
DBV
5
250
195.0
200.0
45.0
TPS73633DCQR
SOT-223
DCQ
6
2500
358.0
335.0
35.0
TPS73633DRBR
SON
DRB
8
3000
346.0
346.0
29.0
TPS73633DRBR
SON
DRB
8
3000
370.0
355.0
55.0
TPS73633DRBT
SON
DRB
8
250
220.0
205.0
50.0
TPS73633DRBT
SON
DRB
8
250
190.5
212.7
31.8
Pack Materials-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated