www.ti.com FEATURES TRS3318 2.5-V 460-kbps RS-232 TRANSCEIVER WITH ±15-kV ESD PROTECTION SLLS820 – AUGUST 2007 1 • • • • • • ESD Protection for RS-232 I/O Pins – ±15 kV Human-Body Model (HBM) – ±8 kV IEC 61000-4-2, Contact Discharge – ±8 kV IEC 61000-4-2, Air-Gap Discharge 300-μA Operating Supply Current 1-μA Low-Power Standby (With Receivers Active) Mode Designed to Transmit at a Data Rate of 460 kbps Auto-Powerdown Plus Option Features Flexible Power-Saving Mode Operates From a Single 2.25-V to 3-V VCC Supply DB OR PW PACKAGE (TOP VIEW) READY C1+ V+ C1− C2+ C2− V− DOUT2 RIN2 ROUT2 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 FORCEOFF VCC GND DOUT1 RIN1 ROUT1 FORCEON DIN1 DIN2 INVALID APPLICATIONS • • • • • • Battery-Powered Systems PDAs Cellular Phones Notebooks Hand-Held Equipment Pagers DESCRIPTION/ORDERING INFORMATION The TRS3318 is a dual-driver, dual-receiver, RS-232 compatible transceiver. The device features auto-powerdown plus and enhanced electrostatic discharge (ESD) protection integrated into the chip. Driver output and receiver input are protected to ±8 kV using the IEC 61000-4-2 Air-Gap Discharge method, ±8 kV using the IEC 61000-4-2 Contact Discharge method, and ±15 kV using the Human-Body Model (HBM). The device operates at a data rate of 460 kbps. The transceiver has a proprietary low-dropout driver output stage enabling RS-232-compatible operation from a 2.25-V to 3-V supply with a dual charge pump. The charge pump requires only four 0.1-μF capacitors and features a logic-level output (READY) that asserts when the charge pump is regulating and the device is ready to begin transmitting. The TRS3318 achieves a 1-μA supply current using the auto-powerdown feature. This device automatically enters a low-power power-down mode when the RS-232 cable is disconnected or the drivers of the connected peripherals are inactive for more than 30 s. The device turns on again when it senses a valid transition at any driver or receiver input. Auto-powerdown saves power without changes to the existing BIOS or operating system. This device is available in two space-saving packages: 20-pin SSOP and 20-pin TSSOP. Flexible control options for power management are featured when the serial port and driver inputs are inactive. The auto-powerdown plus feature functions when FORCEON is low and FORCEOFF is high. During this mode of operation, if the device does not sense valid signal transitions on all receiver and driver inputs for approximately 30 s, the built-in charge pump and drivers are powered down, reducing the supply current to 1 μA. By disconnecting the serial port or placing the peripheral drivers off, auto-powerdown plus can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown plus enabled, the device activates automatically when a valid signal is applied to any receiver or driver input. INVALID is high (valid data) if any receiver input voltage is greater than 2.7 V or less than –2.7 V, or has been between –0.3 V and 0.3 V for less than 30 μs (typical number). INVALID is low (invalid data) if all receiver input voltage are between –0.3 V and 0.3 V for more than 30 μs (typical number). 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2007, Texas Instruments Incorporated TRS3318 2.5-V 460-kbps RS-232 TRANSCEIVER WITH ±15-kV ESD PROTECTION www.ti.com SLLS820 – AUGUST 2007 ORDERING INFORMATION TA PACKAGE SSOP – DB 0°C to 70°C TSSOP – PW SSOP – DB –40°C to 85°C TSSOP – PW (1) (2) (1) (2) ORDERABLE PART NUMBER Tube of 70 TRS3318CDB Reel of 2000 TRS3318CDBR Tube of 70 TRS3318CPW Reel of 2000 TRS3318CPWR Tube of 70 TRS3318IDB Reel of 2000 TRS3318IDBR Tube of 70 TRS3318IPW Reel of 2000 TRS3318IPWR TOP-SIDE MARKING RV18C RV18C RV18I RV18I Package drawings,thermal data, and symbolization are available at www.ti.com/packaging. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. FUNCTION TABLE (1) INPUT CONDITIONS FORCEON FORCEOFF RECEIVER OR DRIVER EDGE WITHIN 30 s OUTPUT STATES VALID RS-232 LEVEL PRESENT AT RECEIVER DRIVER RECEIVER INVALID READY OPERATING MODE Auto-Powerdown Plus Conditions H H No No Active Active L H Normal operation, auto-powerdown plus disabled H H No Yes Active Active H H Normal operation, auto-powerdown plus disabled L H Yes No Active Active L H Normal operation, auto-powerdown plus enabled L H Yes Yes Active Active H H Normal operation, auto-powerdown plus enabled L H No No Z Active L L Power down, auto-powerdown plus enabled L H No Yes Z Active H L Power down, auto-powerdown plus enabled X L X No Z Active L L Manual power down X L X Yes Z Active H L Manual power down Auto-Powerdown Conditions (1) 2 INVALID INVALID X No Z Active L L Power down, auto-powerdown enabled INVALID INVALID X Yes Active Active H H Normal operation, auto-powerdown enabled H = high level, L = low level, X = irrelevant, Z = high impedance Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TRS3318 TRS3318 2.5-V 460-kbps RS-232 TRANSCEIVER WITH ±15-kV ESD PROTECTION www.ti.com SLLS820 – AUGUST 2007 LOGIC DIAGRAM (POSITIVE LOGIC) DIN1 DIN2 FORCEOFF FORCEON ROUT1 13 17 12 8 20 11 14 Auto-Powerdown Plus 15 DOUT1 DOUT2 INVALID 1 READY 16 RIN1 5 kΩ ROUT2 10 9 RIN2 5 kΩ TERMINAL FUNCTIONS TERMINAL NAME DESCRIPTION NO. C1+ 2 Positive voltage-doubler charge-pump capacitor C1– 4 Negative voltage-doubler charge-pump capacitor C2+ 5 Positive inverting charge-pump capacitor C2– 6 Negative inverting charge-pump capacitor DIN 12, 13 CMOS driver inputs DOUT 8, 17 RS-232 driver outputs FORCEOFF 20 Force-off input, active low. Drive low to power down transmitters, receivers, and charge pump. This overrides auto-powerdown and FORCEON (see Function Table). FORCEON 14 Force-on input, active high. Drive high to override auto-powerdown, keeping transmitters and receivers on (FORCEOFF must be high) (see Function Table). GND 18 Ground INVALID 11 Valid signal detector output, active low. A logic high indicates that a valid RS-232 level is present on a receiver input. READY 1 Ready to transmit output, active high. READY is enabled high when V– goes below –3.5 V and the device is ready to transmit. RIN 9, 16 RS-232 receiver inputs ROUT 10, 15 CMOS receiver outputs V+ 3 2 × VCC generated by the charge pump V– 7 –2 × VCC generated by the charge pump VCC 19 2.25-V to 3-V single-supply voltage Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TRS3318 3 TRS3318 2.5-V 460-kbps RS-232 TRANSCEIVER WITH ±15-kV ESD PROTECTION www.ti.com SLLS820 – AUGUST 2007 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range –0.3 6 V V+ Positive supply voltage range (2) –0.3 7 V –7 0.3 V 13 V V– Negative supply voltage range V+ + IV–I Supply voltage differential (2) VI Input voltage VO Output voltage (2) DIN, FORCEON, FORCEOFF to GND 6 RIN to GND ±13.2 ROUT, INVALID, READY to GND –0.3 DOUT to GND Continuous power dissipation (TA = 70°C) (2) V VCC + 0.3 Continuous 16-pin SSOP (derate 7.14 mW/°C above 70°C) 571 20-pin SSOP (derate 8 mW/°C above 70°C 640 20-pin TSSOP (derate 7 mW/°C above 70°C) 559 Storage temperature range –65 Lead temperature (soldering, 10 s) (1) V ±25 DOUT to GND Short-circuit duration Tstg –0.3 UNIT mW 150 °C 300 °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. V+ and V– can have maximum magnitudes of 7 V, but their absolute difference cannot exceed 13 V. Recommended Operating Conditions See Figure 4 MIN NOM Supply voltage 2.25 MAX UNIT 2.5 3 V VIH Driver and control high-level input voltage DIN, FORCEOFF, FORCEON VCC = 2.5 V to 3 V 0.7 × VCC 5.5 V VIL Driver and control low-level input voltage DIN, FORCEOFF, FORCEON VCC = 2.5 V to 3 V 0 0.3 × VCC V VI Receiver input voltage –25 25 V 0 70 –40 85 TA TRS3318C Operating free-air temperature TRS3318I °C Electrical Characteristics VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP (1) MAX UNIT DC Characteristics (VCC = 2.5 V, TA = 25°C) μA Auto-powerdown plus supply current FORCEON = GND, FORCEOFF = VCC, All RIN and DIN idle 1 10 Auto-powerdown supply current FORCEOFF = GND 1 10 μA Supply current FORCEON = FORCEOFF = VCC, No load 0.3 2 mA (1) Typical values are at VCC = 2.5 V, TA = 25°C. ESD Protection PARAMETER TEST CONDITIONS Human-Body Model (HBM) RIN, DOUT 4 TYP IEC 61000-4-2 Air-Gap Discharge method ±8 IEC 61000-4-2 Contact Discharge method ±8 Submit Documentation Feedback UNIT ±15 kV Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TRS3318 TRS3318 2.5-V 460-kbps RS-232 TRANSCEIVER WITH ±15-kV ESD PROTECTION www.ti.com SLLS820 – AUGUST 2007 DRIVER SECTION Electrical Characteristics over recommended ranges of supply voltage and operating free-air temperature, VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4) PARAMETER TEST CONDITIONS MIN TYP (1) Vhys Driver input hysteresis Ion Input leakage current FORCEON, DIN, FORCEOFF Vom Output voltage swing All driver outputs loaded with 3 kΩ to ground ±3.7 ±4 rO Output resistance VCC = 0, Driver output = ±2 V 300 10M IOS Output short-circuit current (2) Ioff Output leakage current (1) (2) MAX 0.3 ±0.01 ±25 VCC = 0 or 2.25 V to 3 V, VOUT = ±12 V, Drivers disabled UNIT V ±1 μA V Ω ±60 mA ±25 μA Typical values are at VCC = 2.5 V, TA = 25°C. Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one output should be shorted at a time. Switching Characteristics over recommended ranges of supply voltage and operating free-air temperature, VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 1) PARAMETER Maximum data rate TEST CONDITIONS MIN RL = 3 kΩ, CL = 1000 pF, One transmitter switching (1) (2) Transition-region slew rate MAX 460 |tPHL – tPLH| Driver skew (2) SR(tr) TYP (1) kbps 100 VCC = 2.5 V, TA = 25°C, RL = 3 kΩ to 7 kΩ, Measured from 3 V to –3 V or –3 V to 3 V, CL = 150 pF to 2500 pF 4 UNIT ns 30 V/μs Typical values are at VCC = 2.5 V, TA = 25°C. Pulse skew is defined as |tPLH – tPHL| of each channel of the same device. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TRS3318 5 TRS3318 2.5-V 460-kbps RS-232 TRANSCEIVER WITH ±15-kV ESD PROTECTION www.ti.com SLLS820 – AUGUST 2007 RECEIVER SECTION Electrical Characteristics over recommended ranges of supply voltage and operating free-air temperature, VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4) PARAMETER TEST CONDITIONS MIN VI Input voltage range VIT+ Input voltage threshold low TA = 25°C VIT– Input voltage threshold high TA = 25°C 0.7 × VCC Vhys Input hysteresis ri Input resistance TA = 25°C 3 Ioff Output leakage current VOL Output voltage low IOUT = 0.5 mA VOH Output voltage high IOUT = –0.5 mA (1) TYP (1) –25 MAX UNIT 25 V 0.3 × VCC V V 0.3 V 5 ±0.05 7 kΩ ±10 μA 0.1 × VCC V 0.9 × VCC V Typical values are at VCC = 2.5 V, TA = 25°C. Switching Characteristics over recommended ranges of supply voltage and operating free-air temperature, VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4) PARAMETER tPHL Receiver propagation delay tPLH |tPHL – tPLH| (1) (2) 6 TEST CONDITIONS RIN to ROUT, CL = 150 pF Receiver skew (2) TYP (1) 0.175 0.175 50 UNIT μs ns Typical values are at VCC = 2.5 V, TA = 25°C. Pulse skew is defined as |tPLH – tPHL| of each channel of the same device. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TRS3318 TRS3318 2.5-V 460-kbps RS-232 TRANSCEIVER WITH ±15-kV ESD PROTECTION www.ti.com SLLS820 – AUGUST 2007 AUTO-POWERDOWN PLUS SECTION Electrical Characteristics over recommended ranges of supply voltage and operating free-air temperature, VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4) PARAMETER TEST CONDITIONS MIN MAX Positive threshold Receiver input threshold to INVALID high 2.7 Negative threshold –2.7 Receiver input threshold INVALID low –0.3 INVALID, READY voltage low IOUT = 0.5 mA INVALID, READY voltage high IOUT = –0.5 mA UNIT V 0.3 V 0.1 × VCC V 0.8 × VCC V Switching Characteristics over recommended ranges of supply voltage and operating free-air temperature, VCC = 2.25 V to 3 V, C1–C4 = 0.1 μF, TA = TMIN to TMAX (unless otherwise noted) (see Figure 4) PARAMETER TEST CONDITIONS MIN TYP (1) MAX UNIT tINVH Receiver positive or negative threshold to INVALID high VCC = 2.5 V 1 μs tINVL Receiver positive or negative threshold to INVALID low VCC = 2.5 V 30 μs tWU Receiver or driver edge to driver enabled VCC = 2.5 V 100 μs tAUTOPRDN Receiver or driver edge to driver shutdown VCC = 2.5 V (1) 15 30 60 s Typical values are at VCC = 2.5 V,TA = 25°C. Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TRS3318 7 TRS3318 2.5-V 460-kbps RS-232 TRANSCEIVER WITH ±15-kV ESD PROTECTION www.ti.com SLLS820 – AUGUST 2007 PARAMETER MEASUREMENT INFORMATION 3V Generator (see Note B) Input RS-232 Output 50 Ω RL CL (see Note A) 3V FORCEOFF TEST CIRCUIT 0V tTHL Output 6V SR(tr) + t THL or tTLH tTLH VOH 3V 3V −3 V −3 V VOL VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 1. Driver Slew Rate 2.25 V Generator (see Note B) RS-232 Output 50 Ω RL Input 1.125 V 1.125 V 0V CL (see Note A) tPLH tPHL VOH 3V FORCEOFF 50% 50% Output VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: PRR = 250 kbit/s, ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 2. Driver Pulse Skew 3V Input 0V 0V −3 V Output Generator (see Note B) tPHL 50 Ω tPLH CL (see Note A) VOH 50% Output 50% VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. The pulse generator has the following characteristics: ZO = 50 Ω, 50% duty cycle, tr ≤ 10 ns, tf ≤ 10 ns. Figure 3. Receiver Propagation Delay Times 8 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TRS3318 TRS3318 2.5-V 460-kbps RS-232 TRANSCEIVER WITH ±15-kV ESD PROTECTION www.ti.com SLLS820 – AUGUST 2007 PARAMETER MEASUREMENT INFORMATION Receiver Inputs } Invalid Region Driver Inputs Driver Outputs VCC INVALID Output tINVL tINVH 0 tWU tWU VCC Ready Output 0 V+ VCC 0 V− VOLTAGE WAVEFORMS ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎ Valid RS-232 Level, INVALID High ROUT Generator (see Note B) 2.7 V 50 Ω Indeterminate 0.3 V 0V If Signal Remains Within This Region For More Than 30 µs, INVALID Is Low† −0.3 V Auto-Powerdown Plus Indeterminate INVALID −2.7 V CL = 30 pF (see Note A) † FORCEON FORCEOFF Valid RS-232 Level, INVALID High DIN DOUT Auto power down disables drivers and reduces supply current to 1 µA. TEST CIRCUIT Figure 4. INVALID Propagation Delay Times and Supply Enabling Time Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TRS3318 9 TRS3318 2.5-V 460-kbps RS-232 TRANSCEIVER WITH ±15-kV ESD PROTECTION www.ti.com SLLS820 – AUGUST 2007 APPLICATION INFORMATION 2.5 V + 0.1 mF 19 CBYPASS 2 C1 0.1 mF C2 0.1 mF + 4 + 5 6 VCC C1+ V+ 3 + C1− V− C2+ 7 C2− 13 DIN1 DOUT1 17 12 DIN2 DOUT2 8 C4 + 0.1 mF RS-232-Compatible Outputs RS-232-Compatible Inputs RIN1 16 15 ROUT1 C3 0.1 mF 5k 10 ROUT2 1 RIN2 9 5k READY To Power-Management Unit Auto-Powerdown INVALID 11 Plus VCC FORCEOFF 20 14 FORCEON GND 18 Figure 5. Typical Application Circuit 10 Submit Documentation Feedback Copyright © 2007, Texas Instruments Incorporated Product Folder Link(s): TRS3318 PACKAGE OPTION ADDENDUM www.ti.com 26-Sep-2007 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TRS3318CDB ACTIVE SSOP DB 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318CDBG4 ACTIVE SSOP DB 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318CDBR ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318CDBRG4 ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318CPW ACTIVE TSSOP PW 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318CPWG4 ACTIVE TSSOP PW 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318CPWR ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318CPWRG4 ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318IDB ACTIVE SSOP DB 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318IDBG4 ACTIVE SSOP DB 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318IDBR ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318IDBRG4 ACTIVE SSOP DB 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318IPW ACTIVE TSSOP PW 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318IPWG4 ACTIVE TSSOP PW 20 70 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318IPWR ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TRS3318IPWRG4 ACTIVE TSSOP PW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 26-Sep-2007 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 4-Oct-2007 TAPE AND REEL BOX INFORMATION Device Package Pins Site Reel Diameter (mm) Reel Width (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TRS3318CDBR DB 20 SITE 41 330 16 8.2 7.5 2.5 12 16 Q1 TRS3318CPWR PW 20 SITE 41 330 16 6.95 7.1 1.6 8 16 Q1 TRS3318IDBR DB 20 SITE 41 330 16 8.2 7.5 2.5 12 16 Q1 TRS3318IPWR PW 20 SITE 41 330 16 6.95 7.1 1.6 8 16 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com Device 4-Oct-2007 Package Pins Site Length (mm) Width (mm) Height (mm) TRS3318CDBR DB 20 SITE 41 346.0 346.0 33.0 TRS3318CPWR PW 20 SITE 41 346.0 346.0 33.0 TRS3318IDBR DB 20 SITE 41 346.0 346.0 33.0 TRS3318IPWR PW 20 SITE 41 346.0 346.0 33.0 Pack Materials-Page 2 MECHANICAL DATA MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001 DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE 28 PINS SHOWN 0,38 0,22 0,65 28 0,15 M 15 0,25 0,09 8,20 7,40 5,60 5,00 Gage Plane 1 14 0,25 A 0°–ā8° 0,95 0,55 Seating Plane 2,00 MAX 0,10 0,05 MIN PINS ** 14 16 20 24 28 30 38 A MAX 6,50 6,50 7,50 8,50 10,50 10,50 12,90 A MIN 5,90 5,90 6,90 7,90 9,90 9,90 12,30 DIM 4040065 /E 12/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-150 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Telephony www.ti.com/telephony Low Power Wireless www.ti.com/lpw Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2007, Texas Instruments Incorporated