CURRENT 16.0 Amperes VOLTAGE 50 to 600 Volts UFR1610 THRU UFR1660 Features · Plastic package has Underwriters Laboratory Flammability Classification 94V-0 · Low forward voltage drop · High current capability · High reliability · Low power loss, high effciency · High surge current capability · High speed switching · Low leakage ITO-220 2.54 · Case : JEDEC ITO-220 molded plastic body · Terminals : Lead solderable per MIL-STD-750, method 2026 · Polarity : As marked · Mounting Position : Any · Weight : 0.08 ounce, 2.24 gram 0.2 PIN 1 PIN 3 Positive CT Suffix "C" 2.7 0.2 15 0.3 0.7 2.54 4.5 0.2 13Min 2.7 0.2 1.3 0.2 3.7 0. 2 Mechanical Data 0.2 0.1 3.2 6.4 0.1 10 0.5 0.2 0.5 2.4 0.2 0.2 0.2 PIN 1 + CASE PIN 2 PIN 3 Negative CT Suffix "A" CASE PIN 2 Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols UFR 1610 UFR 1620 UFR 1630 UFR 1640 UFR 1650 UFR 1660 Units Maximum recurrent peak reverse voltage VRRM 100 200 300 400 500 600 Volts Maximum RMS voltage VRMS 70 140 210 280 350 420 Volts Maximum DC blocking voltage VDC 100 200 300 400 500 600 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length @ at TA=100℃ I(AV) 16.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 200 Amps Maximum instantaneous forward voltage at 8.0A VF 1.0 1.3 Maximum DC reverse current at rated DC blocking voltage TA=25℃ Maximum DC reverse current at rated DC blocking voltage TA=125℃ 1.7 Volts 10.0 μA IR 100 Maximum reverse recovery time (Note 1) Trr 50 80 ns Typical junction capacitance (Note 2) CJ 80 50 pF Typical thermal resistance (Note 3) RθJC Operating junction and storage temperature range TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Thermal resistance from junction to case mounting on heatsink. 2.2 -55 to +150 -55 to +150 ℃/W ℃ RATINGS AND CHARACTERISTIC CURVES UFR1610 THRU UFR1660 FIG . 1 -REVERSE RECOVERY TIME CHARACTERISTIC 10 50 AND TEST CIRCUIT DIAGRAM trr NONINDUCTIVE NONINDUCTIVE DUT (+ ) 50Vdc (approx) (-) +0.5A PULSE GENERATOR ( NOTE 2 ) NONINDUCTIVE OSCILLOSCOPE (NOTE 2 ) -1.0A 1cm . FIG 2 -MAXIMUM AVERAGE FORWARD CURRENT DERATING 1000 20 8 4 0 50 100 CASE TEMPERATURE . ( % ) 150 FIG . 4 -MAXIMUM NON - REPETITIVE FORWARD SURGE CURRENT Tj=25 C o 120 8.3ms Single Half Sine Wave JEDEC Method INSTANTAN EOUS REVERSE CURRET . ( 12 FIG . 3 -TYPICAL REVERSE CHARACTERISTICS 60 100 10 Tj=25 C O 1 0.1 20 40 60 80 100 120 140 FIG . 6 -TYPICAL FRWARD CHARACTERISTICS 100 o 160 UF 120 UF 80 40 1 R1 66 2 R1 61 0-1 0 65 0 0.3 10 20 50 100 200 REVERSE VOLTAGE . ( V) 500 1000 0 65 0.1 Tj=25oC Pulse Width=300 1% Duty Cycle 0.03 .010.4 5 R1 0 1.0 66 Tj=25 C 3.0 R1 200 10 UF FIG . 5 -TYPICAL JUNCTIOON CAPACITANCE PER LEG 30 0 1 00 UF 50 64 5 10 20 NMBER OF CYCLES AT 60Hz 0-1 2 61 1 R1 30 0 O PERCENT OF RATED PEAK REVERSE VOLTAGE . (%) 90 240 Tj=125 C UF 0 SET TIME BASE FOR 5/ 10ns / cm A) 16 INSTANTANEOUS FORWARD CURRENT . ( A) PE A K F O R W A R D S U R G E C U R R E N T . ( A ) AVERAGE FORWARD CURRENT . ( A ) NOTES: 1 . RISE TIME = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22p 2 . RISETIME = 10ns max. SOURSE IMPEDANCE = 50ohmsf CAPACITANCE ( pF) 0 -0.25A 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE . ( V ) s 1.8