USBUF01P6 IPAD™ EMI filter and line termination for USB upstream ports Applications EMI Filter and line termination for USB upstream ports on: ■ ■ USB Hubs PC peripherals Features ■ ■ ■ ■ Monolithic device with recommended line termination for USB upstream ports Integrated Rt series termination and Ct bypassing capacitors. Integrated ESD protection Small package size SOT-666IP (Internal pad) Functional diagram Description 3.3 V The USB specification requires upstream ports to be terminated with pull-up resistors from the D+ and D- lines to Vbus. On the implementation of USB systems, the radiated and conducted EMI should be kept within the required levels as stated by the FCC regulations. In addition to the requirements of termination and EMC compatibility, the computing devices are required to be tested for ESD susceptibility. The USBUF01P6 provides the recommended line termination while implementing a low pass filter to limit EMI levels and providing ESD protection which exceeds IEC 61000-4-2 level 4 standard. The device is packaged in a SOT-666 which is the smallest available lead frame package (45% smaller than the standard SOT323). Rt ■ ■ ■ ■ EMI / RFI noise suppression Required line termination for USB upstream ports ESD protection exceeding IEC 61000-4-2 level 4 High flexibility in the design of high density boards Tailored to meet USB 2.0 standard (low speed and full speed data transmission) Grd 3.3 V Rt D2 D3 Ct Complies with the following standards: IEC 61000-4-2 level4: 15 kV(air discharge) 8 kV(contact discharge) MIL STD 883E-Method 3015-7: Class 3 C = 100 pF R = 1500 Ω 3 positive strikes and 3 negative strikes (F = 1 Hz) Order codes TM: IPAD is a trademeark of STMicroelectronics August 2006 D4 Ct Benefits ■ Rp D1 Rev 6 Part Number Marking USBUF01P6 U 1/9 www.st.com 9 Characteristics 1 USBUF01P6 Characteristics Table 1. Absolute maximum rating (Tamb = 25° C) Symbol Parameter VPP ESD discharge Unit ± 16 ±9 ± 25 kV 150 °C -55 to +150 °C 260 °C -40 to + 85 °C IEC61000-4-2 air discharge IEC61000-4-2 contact discharge MIL STD 883E - Method 3015-7 Junction temperature Tj Tstg Storage temperature range TL Maximum lead temperature for soldering during 10 s at 5 mm for case Top Operating temperature range Table 2. Electrical characteristics (Tamb = 25° C) Symbol Parameter VRM Stand-off voltage VBR Breakdown voltage VCL Clamping voltage IRM Leakage current IPP Peak pulse current αT Voltage temperature coefficient VF Forward voltage drop Rd Dynamic resistance Symbol 2/9 Value Test conditions I IF VF VCL VBR VRM V IRM Slope = 1/Rd Min. Typ. 6 IPP Max. Unit 10 V 500 nA VBR IR = 1 mA IRM VRM = 3.3 V per line Rt Tolerance ± 10% 33 Ω Rp Tolerance ± 10% 1.5 kΩ Ct Tolerance ± 20% 47 pF USBUF01P6 2 Technical information Technical information Figure 1. USB Standard requirements. 3.3V 1.5k Rt Full-speed or Low-speed USB Transceiver Twisted pair shielded Rt Zo = 90ohms 5m max DHost or Hub port 15k Ct Rt D+ D+ Ct 15k Ct Full-speed USB Transceiver Ct Hub 0 or Full-speed function Ct Low-speed USB Transceiver Ct Hub 0 or Low-speed function Rt D- FULL SPEED CONNECTION 3.3V 1.5k Ct Untwisted unshielded Rt 3m max DHost or Hub port Ct 15k Rt D+ D+ Rt Full-speed or Low-speed USB Transceiver Rt D- 15k LOW SPEED CONNECTION Application example Implementation of ST solutions for USB ports. Host/Hub USB por transceivert Downstream port USBUF01W6 USBDF01W5 D2 Rt D+ D+ in Ct Rd D+ out D+ Gnd D+ Ct Ct Rt 3.3 V Rt Gnd DD- in Rt D1 CABLE Gnd Ct Rd Upstream port D+ Peripheral transceiver Figure 2. D- D- Rp D- out D3 3.3V D4 D- FULL SPEED CONNECTION USBUF01W6 USBDF01W5 D2 Rt D+ D+ in Ct Rd D+ out D+ Gnd CABLE D+ Ct Gnd Ct Rt 3.3 V Rt Gnd Ct Rd DD- in Rt D- Upstream port D+ D1 Peripheral transceiver Downstream port Host/Hub USB por transceivert 2.1 D- D- out Rp D3 3.3V D4 D- LOW SPEED CONNECTION 3/9 Technical information 2.1.1 USBUF01P6 EMI filtering Current FCC regulations requires that class B computing devices meet specified maximum levels for both radiated and conducted EMI. ● Radiated EMI covers the frequency range from 30 MHz to 1GHz. ● Conducted EMI covers the 450 kHz to 30 MHz range. For the types of devices utilizing the USB, the most difficult test to pass is usually the radiated EMI test. For this reason the USBUF01P6 device is aiming to minimize radiated EMI. The differential signal (D+ and D-) of the USB does not contribute significantly to radiated or conducted EMI because the magnetic field of both conductors cancels each other. The inside of the PC environment is very noisy and designers must minimize noise coupling from the different sources. D+ and D- must not be routed near high speed lines (clocks spikes). Induced common mode noise can be minimized by running pairs of USB signals parallel to each other and running grounded guard trace on each side of the signal pair from the USB controller to the USBUF device. If possible, locate the USBUF device physically near the USB connectors. Distance between the USB controller and the USB connector must be minimized. The 47 pF (Ct) capacitors are used to bypass high frequency energy to ground and for edge control, and are placed between the driver chip and the series termination resistors (Rt). Both Ct and Rt should be placed as close to the driver chip as is practicable. The USBUF01P6 ensures a filtering protection against electro-magnetic and radio frequency Interference thanks to its low-pass filter structure. This filter is characterized by the following parameters: ● cut-off frequency ● insertion loss ● high frequency rejection. Figure 3. USBUF01P6 typical attenuation curve. Figure 4. Measurement configuration. 0.00 dB --2.50 --5.00 --7.50 50Ω TEST BOARD UUx --10.00 --12.50 Vg --15.00 --17.50 --20.00 --22.50 --25.00 1.0M 3.0M 10.0M 30.0M 100.0M f/Hz 4/9 300.0M 1.0G 3.0G 50Ω USBUF01P6 2.1.2 Technical information ESD protection In addition to the requirements of termination and EMC compatibility, computing devices are required to be tested for ESD susceptibility. This test is described in the IEC 61000-4-2 and is already in place in Europe. This test requires that a device tolerates ESD events and remains operational without user intervention. The USBUF01P6 is particularly optimized to perform ESD protection. ESD protection is based on the use of device which clamps at: V CL = V BR + R d ⋅ I PP This protection function is splitted in 2 stages. As shown in Figure 5. the ESD strikes are clamped by the first stage S1 and then its remaining overvoltage is applied to the second stage through the resistor Rt. Such a configuration makes the output voltage very low at the output. Figure 5. USBUF01P6 ESD clamping behavior. Rg S1 Rt Rd VPP ESD SURGE VBR USBUF01P6 Device to be protected Measurement board. TEST BOARD Vin U 15kV Air Discharge Rload Voutput ESD Surge Figure 6. Rd Vinput VBR S2 Vout To have a good approximation of the remaining voltages at both Vin and Vout stages, we give the typical dynamical resistance value Rd. By taking into account these following hypothesis : Rt>Rd, Rg>Rd and Rload>Rd, it gives these formulas: R g ⋅ V BR + R d ⋅ V g Vinput = ---------------------------------------------Rg R t ⋅ V BR + R d ⋅ Vinput Voutput = --------------------------------------------------------Rt The results of the calculation done for Vg = 8 kV, Rg = 330 Ω (IEC 61000-4-2 standard), VBR = 7 V (typ.) and Rd = 2 Ω (typ.) give: Vinput = 55.48 V Voutput = 10.36 V 5/9 Technical information USBUF01P6 This confirms the very low remaining voltage across the device to be protected. It is also important to note that in this approximation the parasitic inductance effect was not taken into account. This could be few tenths of volts during few ns at the Vinput side. This parasitic effect is not present at the Voutput side due the low current involved after the resistance Rt. The measurements done hereafter show very clearly (Figure 7.a) the high efficiency of the ESD protection: – no influence of the parasitic inductances on Voutput stage – Voutput clamping voltage very close to VBR (breakdown voltage) in the positive way and -VF (forward voltage) in the negative way Figure 7. Remaining voltage at both stages S1 (Vinput) and S2 (Voutput) during ESD surge. a: Positive surge b: Negative surge Please note that the USBUF01P6 is not only acting for positive ESD surges but also for negative ones. For these kinds of disturbances it clamps close to ground voltage as shown in Figure 7.b. 6/9 USBUF01P6 3 Package information Package information Table 3. SOT-666 internal pad dimensions Dimensions Ref. b1 L1 Millimeters Min. Typ. Max. Inches Min. Typ. Max. L4 L3 b D E1 A L2 E A3 A 0.45 0.60 0.018 0.024 A3 0.08 0.18 0.003 0.007 b 0.17 0.34 0.007 0.013 b1 0.19 D 1.50 1.70 0.059 0.067 E 1.50 1.70 0.059 0.067 E1 1.10 1.30 0.043 0.051 Figure 8. 0.34 0.007 0.011 0.013 e 0.50 0.020 L1 0.19 0.007 L2 e 0.27 0.10 0.30 0.004 0.012 L3 0.10 0.004 L4 0.60 0.024 SOT-666 internal pad footprint (dimensions in mm) 0.50 0.30 0.99 0.21 0.62 2.60 1.40 0.20 7/9 Ordering information Table 4. USBUF01P6 Mechanical specifications Lead plating Tin-lead Lead plating thickness 5 µm min 25 µm max Lead material Sn (100% Sn) Lead coplanarity 10 µm max Body material Molded epoxy Flammability UL94V-0 In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 4 5 8/9 Ordering information Part Number Marking Package Weight Base qty Delivery mode USBUF01P6 U SOT-666IP 2.9 mg 3000 Tape and reel Revision history Date Revision Description of Changes September-2003 1 First issue. 01-Jun-2004 2 SOT-666 Internal Pad version package change. 08-Jun-2005 3 Minor format changes; no content changed. 10-Mar-2006 4 Footprint and dimension graphic improved in packaging information. Ecopack statement added. Reformatted to current standard. 16-Aug-2006 5 Updated SOT-666IP package dimensions in Table 3. 29-Aug-2006 6 Typing error in table 2 on page 2: change W and kW unit to Ω and kΩ unit. USBUF01P6 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 9/9