LX7203-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET KEY FEATURES DESCRIPTION Small SC70-6L Package Bi-directional EMI/RFI low-pass filter Line termination with integrated ESD protection Low TVS operating voltage (5.25V) Low leakage current Integrated single die construction Crosses From Semtech STF203 The 47 pF capacitor completes the high frequency filter and controls the edge rate of the USB signals The LX7203 protects both D+ and D- data lines and the voltage bus from ESD. The TVS protection diodes exceed the requirements of IEC61000-4-2, level 4, 15kV (air discharge) and 8kV (contact discharge).The integrated configuration of the LX7203 minimizes board space and allows for ideal placement near the connector. The LX7203 is ideal for use in USB hubs, peripherals and portable appliances APPLICATIONS USB Ports Peripherals Computers and Printers Mobile phones Pagers and PDA’s Digital Cameras IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com PACKAGE ORDER INFO TJ (°C) -40 to 125 -40 to 125 Plastic SM 6-Pin SC70 LX7203-15ISM LX7203-22ISM Package Marking 315 322 WWW . Microsemi .C OM The LX7203 is an integrated Universal Serial Bus (USB) line termination device with an EMI filter and ESD protection diodes. This device offers a cost effective and compact solution for one USB upstream port. The USB v1.1 specification requires line termination resistors on both the D+ and D- lines. These resistors ensure signal integrity by matching the cable impedance to that of the differential driver. The 1.5 kΩ pull-up resistor identifies the appropriate data line for full speed or low speed operation. BENEFITS Tape & Reel Quantity (Reel Size) Filter response characterized up to 6 GHz <2dB insertion loss in the pass band >20dB attenuation in the 800900 MHz range >12dB attenuation in the WLAN frequencies of 2.4GHz and 5.06.0 GHz 3K (7inches) Note: Append the letter “T” to the part number For Tape & Reel Ordering PRODUCT HIGHLIGHT Rs D in from connector D out to IC CEDGE 1.5K DIN 1 from connector RS 6 DOUT to IC C VBUS 2 5 2 GND D in from connector D out Rs to IC DIN 3 from connector ? 5 VBUS C 4 RS LX7203 CEDGE RPU DOUT to IC Functional Schematic with PinOut Circuit Diagram Copyright 2002 Rev. 1.0a, 2002-10-22 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 1 LX7203-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET ABSOLUTE MAXIMUM RATINGS PACKAGE PIN OUT Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. DIN 6 DOUT 1 to IC from connector GND 2 5 VBUS DIN 3 4 DOUT from connector WWW . Microsemi .C OM Steady State Power ................................................................100mW ESD Air Discharge per IEC61000-4-2.......................................16kV ESD Contact Discharge per IEC61000-4-2................................10kV Lead Soldering Temperature (10 Seconds) ............................. 260°C Operating Temperature ........................................... -40°C to +125°C Storage Temperature Range .................................... -55°C to +150°C to IC SM PACKAGE (Top View) THERMAL DATA SM Plastic 6-Pin SC70 THERMAL RESISTANCE-JUNCTION TO CASE, θJC THERMAL RESISTANCE-JUNCTION TO AMBIENT, θJA 119 °C/W 122 °C/W Junction Temperature Calculation: TJ = TA + (PD x θJA). The θJA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. FUNCTIONAL PIN DESCRIPTION Name VBUS Description Bus Voltage DIN Data In GND Ground DOUT Data Out ELECTRICAL CHARACTERISTICS Unless otherwise specified, the following specifications apply over the operating ambient temperature -40°C ≤ TA otherwise noted. Symbol Stand-Off Voltage Breakdown Voltage Leakage Current Series Resistance (-15) Series Resistance (-22) Temperature Coefficient of RS Pull Up Resistance Capacitor VRWM VBR IR RS RS TCOEFF RPU CEDGE Total Capacitance Copyright 2002 Rev. 1.0a, 2002-10-22 CTOT Test Conditions IR = 1mA VRWM = 5.25V, T = 25°C Each Line Each Line Each Line Each Line Each Line Between I/O Pins and Ground, Each Device VR = 0V, f = 1MHz Min +125°C except where LX7203 Typ Max 5.25 6 13.5 19.8 1.35 54 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 15 22 200 1.5 47 60 1 16.5 24.2 1.65 66 Units V V µA Ω Ω ppm KΩ pF pF Page 2 ELECTRICALS Parameter ≤ LX7203-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET APPLICATION CIRCUITS Peripheral (upstream port) LX7201 LX7203 RS 1 4 6 RS 3 C C USB Transceiver WWW . Microsemi .C OM Host or Hub (downstream port) R PD 5 R PU 2 2 RS C 3 6 1 GND V BUS USB Transceiver V BUS GND C R PD 5 4 RS Figure 1 – Typical Application APPLICATION INFORMATION The LX7203 meets the requirements of the USB v1.1 specification for device termination, EMI filtering and ESD protection. The RS resistor provides the proper signal termination; the CEDGE capacitor controls the signal rise and fall slew; the TVS diodes protect the IC from ESD damage; and the total capacitance and resistance creates a low pass filter eliminating the high frequency energy from the circuit. The LX7203 can configure the upstream port for either FullSpeed or Low-Speed operation. The figures below show the proper connection in accordance with the USB v1.1 specification. Host USB Transceiver cable FULL SPEED DEVICE (FIGURE 2) The USB specification offers a 12 Mbps data transfer rate known as Full-Speed which requires a 1.5 kΩ pull-up resistor to be connected to the D+ line. Slew rate control is accomplished with CEDGE attached to the transceiver before the RS. Voltage Supply (Vbus) is connected to Pin 5 Ground is connected to Pin 2 D+ from the connector is routed to Pin 1 (1.5 kΩ pull-up resistor) and Pin 6 to the D+ line of the USB Transceiver D- from the connector is routed to Pin 3 and Pin 4 to the D- line of the USB Transceiver V BUS V BUS GND GND D+ D+ R PU D IN from connector GND 2 D- 6 1 LX7203 3 D IN from connector D OUT to IC APPLICATIONS D- Peripheral USB Transceiver 5 V BUS 4 D OUT to IC Figure 2 – Connection for Full Speed Operation Copyright 2002 Rev. 1.0a, 2002-10-22 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 3 LX7203-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET APPLICATION INFORMATION (CONTINUED) Voltage Supply (Vbus) is connected to Pin 5 Ground is connected to Pin 2 D+ from the connector is routed to Pin 3 and Pin 4 to the D+ line of the USB Transceiver D- from the connector is routed to Pin 1 (1.5 kΩ pull-up resistor) and Pin 6 to the D- line of the USB Transceiver VBUS Host USB Transceiver cable VBUS GND D+ GND D+ D- 1 DIN from connector RPU 6 DOUT to IC LX7203 GND 2 5 VBUS 3 4 WWW . Microsemi .C OM LOW SPEED DEVICE (FIGURE 3) The USB specification offers a 1.5 Mbps data transfer rate known as Low-Speed which requires a 1.5 kΩ pull-up resistor to be connected to the D- line. Slew rate control is accomplished with CEDGE attached to the transceiver before the RS. DPeripheral USB Transceiver DOUT to IC DIN from connector Figure 3 – Connection for Low Speed Operation ELECTROMAGNETIC EMISSION AND SUSCEPTABILITY FCC Part 15 sets limits for maximum allowable EM emission and susceptibility. There are two types of emissions. Conducted emissions with frequency of emission of 0.45 to 30 MHz and radiated emissions with frequency of emission of 30 MHz to 40 GHz. All digital computing devices including the peripheral devices must comply. Examples of peripheral devices include terminals, printers, external floppy disk drives and other data storage devices, video monitors, keyboards, control cards, interface boards, external memory expansion cards and other input/output devices that may or may not contain digital circuitry. LX7203 is optimized to minimize the radiated EMI which is the primary concern in devices using USB. Refer to the typical filter response curve for the attenuation characteristics of LX7203 over the frequency range of 30kHz to 6GHz. APPLICATIONS Copyright 2002 Rev. 1.0a, 2002-10-22 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 LX7203-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET WWW . Microsemi .C OM CHARACTERISTIC CURVES 8KV Contact ESD 1 Ch1 5.0VΩ M Figure 4 – 8KV ESD input pulse as per IEC61000-4-2. Vertical scale is equivalent to 5A/div. M 40.0ns Figure 5 – Clamping Characteristics when device subjected to an 8 KV ESD pulse. GRAPHS Figure 6 – Frequency response curve. Low insertion loss in the pass band and -20dB attenuation at 800-900 MHz. Better than -10dB attenuation at the WLAN frequencies of 2.4 and 5.0-6.0 GHz. Copyright 2002 Rev. 1.0a, 2002-10-22 5.0V Ω 40.0ns Figure 7 – Analog Crosstalk between the two datalines Dand D+ Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 5 LX7203-xx I N T E G R A T E D EMI Filter & ESD Protection for Up Stream USB Ports P R O D U C T S P RODUCTION D ATA S HEET SM WWW . Microsemi .C OM PACKAGE DIMENSIONS 6 Pin Plastic SC70 B K F C A G D J E MILLIMETERS MIN MAX 1.15 1.35 1.80 2.20 1.80 2.40 0.15 0.30 0.65 BSC 0.10 0.40 0 0.10 0.80 1.00 0.80 1.10 0.10 0.18 0.10 0.30 INCHES MIN MAX 0.045 0.053 0.071 0.086 0.071 0.094 0.006 0.012 0.026 BSC 0.004 0.016 0 0.004 0.032 0.039 0.032 0.043 0.004 0.007 0.004 0.012 Note: H I Dim A B C D E F G H I J K 1. Dimensions do not include mold flash or protrusions; these shall not exceed 0.155mm(.006”) on any side. Lead dimension shall not include solder coverage. Recommended Footprint X Dim C D E X Y Y C (ref) MILLIMETERS MIN MAX 1.60 1.30 0.65 0.35 0.90 INCHES MIN MAX 0.063 0.052 0.026 0.014 0.035 MECHANICALS E (ref) D (ref) Copyright 2002 Rev. 1.0a, 2002-10-22 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 6 LX7203-xx I N T E G R A T E D P R O D U C T S EMI Filter & ESD Protection for Up Stream USB Ports P RODUCTION D ATA S HEET WWW . Microsemi .C OM NOTES NOTES PRODUCTION DATA – Information contained in this document is proprietary to Microsemi and is current as of publication date. This document may not be modified in any way without the express written consent of Microsemi. Product processing does not necessarily include testing of all parameters. Microsemi reserves the right to change the configuration and performance of the product and to discontinue product at any time. Copyright 2002 Rev. 1.0a, 2002-10-22 Microsemi Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 7 KD Signatu re Not Verified Digitally signed by KD DN: cn=KD, o=Micros emi, c=US Date: 2002.10.2 2 13:20:51 -07'00'