VCC6-107 +/-20 ppm LVPECL Oscillator Features • +/-20 ppm, including aging • 3rd Overtone Crystal for best jitter performance • Output frequencies to 200 MHz • Low Jitter • Enable/Disable output for test and board debug • -10/70 °C operating temperature • Hermetically sealed ceramic SMD package • Product is compliant to RoHS directive and fully compatible with lead free assembly The VCC6-107 Crystal Oscillator Applications • WLAN • SONET/SDH/DWDM • Ethernet, Gigabit Ethernet • Storage Area Network • Digital Video • Broadband Access fO Output Buffer / Disable Vectron International 267 Lowell Road, Hudson NH 03051 Description Vectron’s VCC6 Crystal Oscillator (XO) is quartz stabilized square wave generator with a LV-PECL output, operating off a 3.3 volt supply. Tel: 1-88-VECTRON-1 e-mail: [email protected] VCC6-107 Crystal Oscillator Performance Characteristics Table 1. Electrical Performance Parameter Frequency Supply Voltage 1 Supply Current Output Logic Levels Output Logic High2 Output Logic Low2 Transition Times Rise Time2 Fall Time2 Output Load Symmetry or Duty Cycle3 Operating temperature Stability 4 RMS Jitter, 12kHz to 20 MHz Period RMS Jitter Cycle to Cycle RMS Jitter Output Enabled5 Output Disabled5 Output Enable/Disable time Enable/Disable Leakage Current Package Size Symbol fO VDD IDD Min 40 3.135 Typical VOH VOL VDD-1.025 VDD-1.810 3.3 Maximum 200 3.465 98 Units MHz V mA VDD-0.880 VDD-1.620 V V 600 600 ps ps 55 % °C ppm ps ps ps V V ns uA mm tR tF SYM 45 50 ohms to VDD-2V 50 -10/70 0.3 2.7 4.8 +/-20 0.7 0.7*VDD 0.3*VDD 400 ±200 IE/D 5.0 x 7.0 x 1.5 1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended. 2. Figure 1 defines these parameters. Figure 2 illustrates the operating conditions under which these parameters are tested and specified. 3. Symmetry is defined as Vs, On Time/Period. 4. Includes calibration tolerance, operating temperature, supply voltage variations, aging (10 years @ 40 degreesC) and shock and vibration (not under operation). 5. Output will be enabled if enable/disable is left open. 6. Jitter is measured using a LeCroy8600 sampling 50,000 cycles. tF tR 80 % Vs 20 % On Time Period Figure 1. Output Waveform Vectron International 267 Lowell Rd, Hudson NH 03051 Figure 2. Typical Output Test Conditions (25±5°C) Tel: 1-88-VECTRON-1 e-mail: [email protected] VCC6-107 Crystal Oscillator VCC6-107-155M52 Accelerated Life Test at 125C 50.0 10.0 0.0 0 10 20 30 40 50 60 -10.0 70 Freq Change from Nominal, PPM Frequency, PPM 20.0 25.0 0.0 100 1000 10000 -25.0 -50.0 -20.0 Hours of Aging Temperature, C Figure 3. Temperature Stability Figure 4. Aging Stability Outline Diagram and Pin Out Pin # Symbol Function 1 2 3 4 5 6 E/D NC GND fO Cf o V DD Enable/Disable function No Connection Ground Output Frequency Complementary Output Frequency Supply Voltage Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: [email protected] 100000 VCC6-107 Crystal Oscillator Tape and Reel J F D G C B A I L E H Tape and Reel Dimensions (mm) Tape Dimensions Product A B C D E VCC6 16 7.5 2.0 4 K Reel Dimensions F G H 8 2 21 13 I J K L 55 2 17 180 # Per Reel 250 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Table 2. Absolute Maximum Ratings Parameter Symbol Power Supply VDD Enable/Disable VIN Storage Temperature Tstorage Ratings -0.5 to +7.0 -0.5 to VDD+0.5 -55/125 Unit Vdc Vdc °C Reliability The VCC6 qualification tests include the following: Table 3. Environnemental Compliance Parameter Mechanical Shock Mechanical Vibration Solderability Gross and Fine Leak Resistance to Solvents Vectron International 267 Lowell Rd, Hudson NH 03051 Conditions MIL-STD-883 Method 2002 MIL-STD-883 Method 2007 MIL-STD-883 Method 2003 MIL-STD-883 Method 1014 MIL-STD-883 Method 2016 Tel: 1-88-VECTRON-1 e-mail: [email protected] VCC6-107 Crystal Oscillator Handling Precautions Although ESD protection circuitry has been designed into the the VCC6, proper precautions should be taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be used for comparison purposes. Table 4. ESD Ratings Model Human Body Model Charged Device Model Minimum 1000 1000 Conditions MIL-STD-883 Method 3115 JESD 22-C101 Suggested IR profile The VCC6 has been qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements and parameters are listed in Table 5. As the contact pads are gold over nickel, devices can be reflowed at lower temperatures. The VCC6 is hermetically sealed so an aqueous wash is not an issue. Table 5. Reflow Profile Parameter PreHeat Time Ramp Up o Time Above 217 C Time To Peak Temperature Time at 260oC (max) Time at 240°C (max) Ramp Down Symbol tS Value 60 sec Min, 180 sec Max R UP tL 3 oC/sec Max 60 sec Min, 150 sec Max 480 sec Max 10 sec Max 60 sec Max 6 oC/sec Max t AMB-P tP tp2 R DN Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 5 e-mail [email protected] VCC6-107 Crystal Oscillator Table 6. Standard Frequencies (MHz) 87.000 163.235 155.520 173.3708 156.250 173.438 159.375 175.000 161.1328 187.500 Other frequencies may be available upon request. Standard frequencies are frequencies which the crystal has been designed and does not imply a stock position. Ordering Information VCC6 - 107 – xxxMxx Product Family Frequency in MHz LVPECL Crystal Oscillator example: 155M52= 155.520 MHz Stability Option/Temperature +/-20ppm over -10 to 70°C For Additional Information, Please Contact: www.vectron.com USA: Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • Fax: 1-888-FAX-VECTRON EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany • Tel: 49 (0) 7268 8010 • Fax: 49 (0) 7268 801281 ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd., WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131 •Tel: 8621 50480777 • Fax: 8621 50481881 Vectron International reserves the right to make changes to the product(s) and/or information contained herein without notice. as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. No liability is assumed VCC6-107 (REVISION DATE: April 17, 2006) Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 6 e-mail [email protected]