I N D U C T O R S May 2013 Inductors for Power Circuits Wound Ferrite VLPseries VLP6045L VLP8040 (1/12) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20130516 / e531_vlp.fm (2/12) I N D U C T O R S Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Inductors for Power Circuits Wound Ferrite Overview of the VLP Series FEATURES Magnetic shield type wound inductor for power circuits. Magnetic shield construction with ferrite resin material. APPLICATION Thin-screen TVs, printers, laptop computers, other PART NUMBER CONSTRUCTION VLP Series name 6045 L×W×H Dimensions (mm max.) 6045 6.8×6.8×4.5 8040 8.6×8.7×4.0 L T internal code Packaging style T Taping - 1R0 N Inductance (µH) 1R0 1.0 100 10 101 100 Inductance tolerance M ±20% N ±30% OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Operating Storage temperature temperature (pieces/reel) （°C） （°C） VLP6045L –40 to +105 –40 to +105 1000 VLP8040 –40 to +105 –40 to +105 1000 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. Type Individual weight （mg） 536 840 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm (3/12) I N D U C T O R S Overview of the VLP Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 220°C 40s Peak Temp. T4 260°C Time t3 5s • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm (4/12) I N D U C T O R S VLP series VLP6045L Type SHAPE & DIMENSIONS 1.6 2.2 6.0±0.2 100 6.8max. 2.2 2.0 6.0±0.3 4.5max. 6.8max. Dimensions in mm 6.6 RECOMMENDED LAND PATTERN 2.55 1.4 2.55 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm (5/12) I N D U C T O R S VLP series VLP6045L Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (µH) 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 Tolerance ±30% ±30% ±30% ±30% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% Measuring frequency (kHz) 100 100 100 100 100 100 100 100 100 100 100 100 100 DC resistance ( ) max. 0.017 0.024 0.026 0.033 0.038 0.057 0.072 0.112 0.140 0.202 0.299 0.455 0.663 typ. 0.013 0.018 0.020 0.025 0.029 0.044 0.055 0.086 0.108 0.155 0.230 0.350 0.510 Rated current(A) max. typ. Idc1 Idc2 8.6 6.5 7.2 5.4 6.4 5.1 5.2 4.6 4.4 4.1 3.8 3.3 3.2 3.0 2.5 2.3 2.1 2.0 1.6 1.5 1.4 1.4 1.1 1.0 0.9 0.8 Part No. VLP6045LT-1R0N VLP6045LT-1R5N VLP6045LT-2R2N VLP6045LT-3R3N VLP6045LT-4R7M VLP6045LT-6R8M VLP6045LT-100M VLP6045LT-150M VLP6045LT-220M VLP6045LT-330M VLP6045LT-470M VLP6045LT-680M VLP6045LT-101M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the nominal value) Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating) ○ Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm (6/12) I N D U C T O R S VLP series VLP6045L Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 1000 101M 680M 470M 330M 100 220M 150M 100M Inductance(µH) 6R8M 4R7M 3R3N 10 2R2N 1R5N 1 0.1 0.01 1R0N 0.1 1 Frequency(MHz) 10 100 ○ Measurement equipment Product No. Manufacturer 4294A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm (7/12) I N D U C T O R S VLP series VLP6045L Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 1000 100 101M 680M 470M Inductance(µH) 330M 220M 150M 10 100M 6R8M 4R7M 3R3N 2R2N 1R5N 1 1R0N 0.1 0.0 2.0 4.0 6.0 DC current(A) 8.0 10.0 12.0 ○ Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm (8/12) I N D U C T O R S VLP series VLP8040 Type 7.4 8.0±0.2 8.7max. 220 SHAPE & DIMENSIONS 8.6max. 1.6 2.675 4.0max. 2.675 Dimensions in mm 8.2 RECOMMENDED LAND PATTERN 3.3 1.4 3.3 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm (9/12) I N D U C T O R S VLP series VLP8040 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (µH) 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 220 330 680 Tolerance ±30% ±30% ±30% ±30% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% Measuring frequency (kHz) 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 DC resistance ( ) max. 0.011 0.013 0.015 0.020 0.025 0.032 0.038 0.058 0.075 0.11 0.16 0.23 0.33 0.49 0.73 1.1 2.2 typ. 0.008 0.010 0.012 0.015 0.019 0.024 0.032 0.048 0.062 0.090 0.13 0.19 0.28 0.41 0.61 0.89 1.8 Rated current(A) max. typ. Idc1 Idc2 9.4 7.0 7.8 6.7 6.7 6.2 5.2 5.2 4.4 4.5 3.6 4.0 3.2 3.5 2.6 2.9 2.2 2.5 1.8 2.1 1.5 1.7 1.2 1.4 1.0 1.2 0.8 1.0 0.6 0.8 0.5 0.7 0.3 0.5 Part No. VLP8040T-1R0N VLP8040T-1R5N VLP8040T-2R2N VLP8040T-3R3N VLP8040T-4R7M VLP8040T-6R8M VLP8040T-100M VLP8040T-150M VLP8040T-220M VLP8040T-330M VLP8040T-470M VLP8040T-680M VLP8040T-101M VLP8040T-151M VLP8040T-221M VLP8040T-331M VLP8040T-681M Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (30% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 40°C by self heating) ○ Measurement equipment Measurement item Product No. L 4194A DC resistance VP-2941A Rated current Idc1 4285A+42841A+42842C ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Panasonic Agilent Technologies • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm (10/12) I N D U C T O R S VLP series VLP8040 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 10000 681M 331M 221M 1000 151M 101M 680M 470M 330M 100 220M Inductance(µH) 150M 100M 6R8M 4R7M 10 3R3N 2R2N 1R5N 1R0N 1 0.1 0.01 0.1 1 Frequency(MHz) 10 100 ○ Measurement equipment Product No. Manufacturer 4294A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm (11/12) I N D U C T O R S VLP series VLP8040 Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 1000 681M 331M 221M 100 151M 101M 680M 470M Inductance(µH) 330M 220M 150M 10 100M 6R8M 4R7M 3R3N 2R2N 1R5N 1 1R0N 0.1 0.0 2.0 4.0 6.0 8.0 10.0 DC current(A) 12.0 14.0 16.0 18.0 ○ Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm (12/12) I N D U C T O R S VLP series Packaging Style REEL DIMENSIONS 2.0±0.5 B Type VLP6045L VLP8040 A ø330 ø330 B 22.4 22.4 C ø100 ø100 D 16.4 16.4 E 2 2 C * These values are typical values. (1.0) ø13.0±0.5 E D ø21.0±0.8 A Dimensions in mm P2 P0 P1 K t A0 Type A0 VLP6045L 6.8 VLP8040 8.8 B0 6.8 8.0 øD0 1.5+0.1/-0 1.5+0.1/-0 B0 W F øD0 E TAPE DIMENSIONS E 1.75±0.1 1.75±0.1 F 7.5±0.1 7.5±0.1 Dimensions in mm P0 P1 P2 W 4.0±0.1 10.0±0.1 2.0±0.1 16.0±0.3 4.0±0.1 12.0±0.1 2.0±0.1 16.0±0.3 K 4.8 4.3 t 0.4 0.4 • All specifications are subject to change without notice. 001-01 / 20130516 / e531_vlp.fm