W184 Six Output Peak Reducing EMI Solution Features Table 1. Modulation Width Selection • Cypress PREMIS™ family offering • Generates an EMI optimized clocking signal at the output • Selectable input to output frequency • Six 1.25%, 3.75%, or 0% down or center spread outputs • One non-Spread reference output • Integrated loop filter components • Operates with a 3.3 or 5V supply • Low power CMOS design • Available in 24-pin SSOP (Shrunk Small Outline Package) • Outputs may be selectively disabled SS% W184 Output 0 Fin ≥ Fout ≥ Fin – 1.25% Fin + 0.625% ≥ Fin≥ – 0.625% 1 Fin ≥ Fout ≥ Fin – 3.75% Fin + 1.875% ≥ Fin≥ –1.875% Table 2. Frequency Range Selection FS2 FS1 Frequency Range 0 0 8 MHz ≤ FIN ≤ 10 MHz 0 1 10 MHz ≤ FIN ≤ 15 MHz 1 0 15 MHz ≤ FIN ≤ 18 MHz 1 1 18 MHz ≤ FIN ≤ 28 MHz Key Specifications Supply Voltages: ...........................................VDD = 3.3V±5% or VDD = 5V±10% Frequency Range: .............................. 8 MHz ≤ Fin ≤ 28 MHz Crystal Reference Range.................... 8 MHz ≤ Fin ≤ 28 MHz W184-5 Output Table 3. Output Enable EN1 EN2 Selectable Spread Percentage: ....................1.25% or 3.75% 0 0 Low Low Output Duty Cycle: ............................... 40/60% (worst case) 0 1 Low Active Output Rise and Fall Time: .................................. 5 ns (max.) 1 0 Active Low 1 1 Active Active Cycle to Cycle Jitter: ........................................ 300 ps (max.) Simplified Block Diagram CLK0:4 CLK5 Pin Configuration 3.3 or 5.0V SSOP REFOUT FS2 X1 X2 GND X1 X2 W184 Spread Spectrum Outputs (EMI suppressed) SS% EN2 GND 3.3 or 5.0V Oscillator or Reference Input W184 CLK0 VDD CLK1 CLK2 W184/W184-5 XTAL Input 1 2 3 4 5 6 7 8 24 23 22 21 20 19 18 17 11 16 15 14 12 13 9 10 SSON# RESET FS1 VDD VDD NC EN1 CLK5 VDD CLK4 GND CLK3 Spread Spectrum Outputs (EMI suppressed) PREMIS is a trademark of Cypress Semiconductor Corporation. Cypress Semiconductor Corporation Document #: 38-07157 Rev. ** • 3901 North First Street • San Jose • CA 95134 • 408-943-2600 Revised September 25, 2001 W184 Pin Definitions Pin Name CLK0:5 Pin No. Pin Type Pin Description 9, 11, 12, 13, 15, 17 O Modulated Frequency Outputs: Frequency modulated copies of the unmodulated input clock (SSON# asserted). CLKIN or X1 3 I Crystal Connection or External Reference Frequency Input: This pin has dual functions. It may either be connected to an external crystal, or to an external reference clock. NC or X2 4 I Crystal Connection: If using an external reference, this pin must be left unconnected. SS% 6 I Modulation Width Selection: When Spread Spectrum feature is turned on, this pin is used to select the amount of variation and peak EMI reduction that is desired on the output signal. This pin has an internal pull-up resistors. Reset 23 I Modulation Profile Restart: A rising edge on this input restarts the modulation pattern at the beginning of its defined path. This pin has an internal pull-down resistor. REFOUT 14 O Non-Modulated Output: This pin provides a copy of the reference frequency. This output will not have the Spread Spectrum feature enabled regardless of the state of logic input SSON#. 18, 7 I Output Enable Select Pins: These pins control the activity of specific output buffers. Set them to disable unused outputs using Table 3 as a guide. 24 I Spread Spectrum Control (Active LOW): Asserting this signal (active LOW) turns the internal modulation waveform on. This pin has an internal pull-down resistor. FS1:2 22, 2 I Frequency Selection Bit 1 and 2: These pins select the frequency of operation. Refer to Table 1. These pins have internal pull-up resistors. VDD 10, 16, 20, 21 P Power Connection: Connected to 3.3V or 5V power supply. EN1:2 SSON# Document #: 38-07157 Rev. ** Page 2 of 9 W184 Overview The W184 products are one series of devices in the Cypress PREMIS family. The PREMIS family incorporates the latest advances in PLL spread spectrum frequency synthesizer techniques. By frequency modulating the output with a lowfrequency carrier, peak EMI is greatly reduced. Use of this technology allows systems to pass increasingly difficult EMI testing without resorting to costly shielding or redesign. In a system, not only is EMI reduced in the various clock lines, but also in all signals which are synchronized to the clock. Therefore, the benefits of using this technology increase with the number of address and data lines in the system. The Simplified Block Diagram shows a simple implementation. Functional Description The W184 uses a Phase-Locked Loop (PLL) to frequency modulate an input clock. The result is an output clock whose frequency is slowly swept over a narrow band near the input signal. The basic circuit topology is shown in Figure 1. The input reference signal is divided by Q and fed to the phase detector. A signal from the VCO is divided by P and fed back to the phase detector also. The PLL will force the frequency of the VCO output signal to change until the divided output signal and the divided reference signal match at the phase detector input. The output frequency is then equal to the ratio of P/Q times the reference frequency. (Note: For the W184 the output frequency is nominally equal to the input frequency.) The unique feature of the Spread Spectrum Frequency Timing Generator is that a modulating waveform is superimposed at the input to the VCO. This causes the VCO output to be slowly swept across a predetermined frequency band. Because the modulating frequency is typically 1000 times slower than the fundamental clock, the spread spectrum process has little impact on system performance. Frequency Selection With SSFTG In Spread Spectrum Frequency Timing Generation, EMI reduction depends on the shape, modulation percentage, and frequency of the modulating waveform. While the shape and frequency of the modulating waveform are fixed for a given frequency, the modulation percentage may be varied. Using frequency select bits (FS1:2 pins), the frequency range can be set. Spreading percentage may be selected to 1.25% or 3.75% (see Table 1). A larger spreading percentage improves EMI reduction. However, large spread percentages may either exceed system maximum frequency ratings or lower the average frequency to a point where performance is affected. For these reasons, spreading percentage options are provided. VDD Clock Input Reference Input Freq. Divider Q Phase Detector Charge Pump Σ VCO Post Dividers CLKOUT (EMI suppressed) Modulating Waveform Feedback Divider P PLL GND Figure 1. Functional Block Diagram Document #: 38-07157 Rev. ** Page 3 of 9 W184 Spread Spectrum Frequency Timing Generation Where P is the percentage of deviation and F is the frequency in MHz where the reduction is measured. The output clock is modulated with a waveform depicted in Figure 3. This waveform, as discussed in “Spread Spectrum Clock Generation for the Reduction of Radiated Emissions” by Bush, Fessler, and Hardin produces the maximum reduction in the amplitude of radiated electromagnetic emissions. Figure 3 details the Cypress spreading pattern. Cypress does offer options with more spread and greater EMI reduction. Contact your local Sales representative for details on these devices. The device generates a clock that is frequency modulated in order to increase the bandwidth that it occupies. By increasing the bandwidth of the fundamental and its harmonics, the amplitudes of the radiated electromagnetic emissions are reduced. This effect is depicted in Figure 2. As shown in Figure 2, a harmonic of a modulated clock has a much lower amplitude than that of an unmodulated signal. The reduction in amplitude is dependent on the harmonic number and the frequency deviation or spread. The equation for the reduction is: dB = 6.5 + 9*log10(P) + 9*log10(F) EMI Reduction Typical Clock Amplitude (dB) Amplitude (dB) SSFTG Spread Spectrum Enabled NonSpread Spectrum Frequency Span (MHz) Down Spread Frequency Span (MHz) Center Spread Figure 2. Clock Harmonic with and without SSCG Modulation Frequency Domain Representation 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 100% 90% 80% 70% 60% 50% 40% 30% 20% 10% FREQUENCY MAX. MIN. Figure 3. Typical Modulation Profile Document #: 38-07157 Rev. ** Page 4 of 9 W184 Absolute Maximum Ratings Stresses greater than those listed in this table may cause permanent damage to the device. These represent a stress rating only. Operation of the device at these or any other conditions above those specified in the operating sections of this specification is not implied. Maximum conditions for extended periods may affect reliability. . Parameter Description Rating Unit VDD, VIN Voltage on any pin with respect to GND –0.5 to +7.0 V TSTG Storage Temperature –65 to +150 °C TB Ambient Temperature under Bias –55 to +125 °C TA Operating Temperature 0 to +70 °C PD Power Dissipation 0.5 W DC Electrical Characteristics: 0°C < TA < 70°C, VDD = 3.3V ±5% Parameter Description IDD Supply Current tON Power Up Time Test Condition Min. Typ. Max. Unit 18 32 mA 5 ms First locked clock cycle after Power Good VIL Input Low Voltage VIH Input High Voltage VOL Output Low Voltage VOH Output High Voltage IIL Input Low Current Note 1 IIH Input High Current Note 1 IOL Output Low Current @ 0.4V, VDD = 3.3V 15 mA IOH Output High Current @ 2.4V, VDD = 3.3V 15 mA 0.8 2.4 V V 0.4 2.4 V V µA –50 50 µA CI Input Capacitance All pins except CLKIN CI Input Capacitance CLKIN pin only RP Input Pull-Up Resistor 500 kΩ ZOUT Clock Output Impedance 25 Ω 6 7 pF 10 pF Note: 1. Inputs FS1:2, SS% have a pull-up resistor; Input SSON# has a pull-down resistor. Document #: 38-07157 Rev. ** Page 5 of 9 W184 DC Electrical Characteristics: 0°C < TA < 70°C, VDD = 5V ±10% Parameter Description Test Condition Min. Typ. Max. Unit 30 50 mA 5 ms 0.15VDD V IDD Supply Current tON Power Up Time VIL Input Low Voltage VIH Input High Voltage VOL Output Low Voltage VOH Output High Voltage IIL Input Low Current Note 2 IIH Input High Current Note 2 IOL Output Low Current @ 0.4V, VDD = 5V 24 mA IOH Output High Current @ 2.4V, VDD = 5V 24 mA CI Input Capacitance All pins except CLKIN CI Input Capacitance CLKIN pin only RP Input Pull-Up Resistor 500 kΩ ZOUT Clock Output Impedance 25 Ω First locked clock cycle after Power Good 0.7VDD V 0.4 2.4 V V µA –50 50 6 µA 7 pF 10 pF AC Electrical Characteristics: TA = 0°C to +70°C, VDD = 3.3V ±5% or 5V±10% Symbol Parameter Test Condition Min. Typ. Max. Unit fIN Input Frequency Input Clock 8 28 MHz fOUT Output Frequency Spread Off 8 28 MHz tR Output Rise Time VDD, 15-pF load 0.8V–2.4V 2 5 ns tF Output Fall Time VDD, 15-pF load 2.4V–0.8V 2 5 ns tOD Output Duty Cycle 15-pF load 40 60 % tID Input Duty Cycle 40 60 % tJCYC Jitter, Cycle-to-Cycle 300 ps EMIRED Harmonic Reduction tSK Output to Output Skew 250 fout = 40 MHz, third harmonic measured, reference board, 15-pF load 8 dB 200 ps Note: 2. Inputs FS1:2 have a pull-up resistor; Input SSON# has a pull-down resistor. Document #: 38-07157 Rev. ** Page 6 of 9 W184 Application Information placed as close to the VDD pin as possible, otherwise the increased trace inductance will negate its decoupling capability. The 10-µF decoupling capacitor shown should be a tantalum type. For further EMI protection, the VDD connection can be made via a ferrite bead, as shown. Recommended Circuit Configuration For optimum performance in system applications the power supply decoupling scheme shown in Figure 4 should be used. VDD decoupling is important to both reduce phase jitter and EMI radiation. The 0.1-µF decoupling capacitor should be R1 Clock Output 24 Logic Input 2 23 Logic Input Reference Input 3 22 Logic Input 4 5 6 7 8 9 10 11 12 21 20 19 18 17 16 15 14 13 XTAL connection or NC Logic Input Logic Input Clock Output Clock Output Clock Output R1 R1 R1 W184 1 Logic Input C1 0.1 µF NC Logic Input Clock Output R1 C1 0.1 µF Clock Output R1 C1 0.1 µF Clock Output R1 C1 0.1 µF 3.3 or 5V System Supply FB C2 10-µF Tantalum Figure 4. Recommended Circuit Configuration Ordering Information Ordering Code Package Name W184 W184-5 Document #: 38-07157 Rev. ** H Package Type 24-Pin SSOP (209-mil) Page 7 of 9 W184 Package Diagram 24-Pin Shrink Small Outline Package (SSOP, 209 mils) Document #: 38-07157 Rev. ** Page 8 of 9 © Cypress Semiconductor Corporation, 2001. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. W184 Document Title: W184 Six Output Peak Reducing EMI Solution Document Number: 38-07157 REV. ECN NO. Issue Date Orig. of Change ** 110267 12/15/01 SZV Document #: 38-07157 Rev. ** Description of Change Change from Spec number: 38-00797 to 38-07157 Page 9 of 9