VISHAY WSL2010E10E0YETA

WSL....E
Vishay
Power Metal Strip Flip Chip (Extended Range)
Patents Pending
FEATURES
• SMD alternative for low power leaded wirewound resistors
• Excellent stability in different environmental conditions
• Superior overload and pulse handling capability compared
to thin film
• Low TCR
• Low noise: < 0.01µV(rms)/Volt
• Voltage coefficient: < 0.00001%/Volt (< 0.1ppm/V)
• Very low inductance: < 0.08µH
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
SIZE
INCH
POWER
RATING
P70°C
LIMITING ELEMENT
VOLTAGE 1) MAX
V쓖
TEMPERATURE
COEFFICIENT
ppm/K
TOLERANCE
RESISTANCE
2)
RANGE
E-SERIES
%
Ω
WSL1506E
1506
0.25
63
15, 25
0.5, 1
0R5 – 10K
96
WSL2010E
2010
0.5
100
15, 25
0.5, 1
0R5 – 10K
96
WSL2512E
2512
1.0
100
15, 25
0.5, 1
0R5 – 10K
96
• Ask about further value ranges, tighter tolerances and TCR’s.
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material
• 4-Digit Marking, according to MIL-PRF-55342 (except as noted in Ordering Information table), on top side
1)
Rated voltage: PxR
2)
Contact factory using e-mail address at bottom of this page for resistance values available between 0R5 - 10R for 1506 and 0R5 - 100R for 2010 and 2512
TECHNICAL SPECIFICATIONS
PARAMETER
Rated Dissipation at 70°C
Limiting Element Voltage 1)
Insulation Voltage (1 min)
Thermal Resistance
Insulation Resistance
Category Temperature Range
Weight / 1000pcs
3)
UNIT
W
V쓖
WSL1506E
0.25
63
200
≤ 220 3)
Vdc/ac peak
K/W
MΩ
°C
g
WSL2010E
0.5
100
200
≤ 88 3)
> 10 6
- 55 / + 150
25
12
WSL2512E
1.0
100
200
≤ 65 3)
35
Depending on solder pad dimensions
PACKAGING
MODEL
REEL
TAPE WIDTH
DIAMETER
PIECES/REEL
CODE
WSL1506E
12mm/Embossed Plastic
180mm/7”
4000
R86
WSL2010E
12mm/Embossed Plastic
180mm/7”
4000
R86
WSL2512E
12mm/Embossed Plastic
180mm/7”
2000
R86
Embossed Carrier Tape per EIA-481-1.2
ORDERING INFORMATION
WSL1506E
MODEL
www.vishay.com
94
10E0
RESISTANCE VALUE & TOLERANCE
Ω&±%
Resistance
Multiplier
Symbol
Tolerance (±)
0.5
X1
W
0.5
X1,000
X
0.5
X1,000,000
Y
1.0
X1
D
1.0
X1,000
E
1.0
X1,000,000
F
X
TA
TC
± ppm/K
E = ± 25ppm/K
X = ± 15ppm/K
PACKAGING
TA = R86 Blistertape
The above part number is for a WSL1506E 10KΩ
± 1% ± 15ppm/K R86 resistor
For Technical Questions in Europe contact: [email protected]
For Technical Questions in Americas/Asia contact: [email protected]
Document Number 20033
Revision 11-Oct-02
WSL....E
Vishay
Power Metal Strip Flip Chip (Extended Range)
Patents Pending
DIMENSIONS
L
SIZE
T
W
d
D
I
INCH
L
W
Tmax
1506
0.15 ± 0.005
[3.81 ±0.13]
0.062 ± 0.003
[1.57 ±0.08]
0.025
[0.64]
0.012 ± 0.003 0.059 ± 0.003
[0.30 ±0.08]
[1.50 ±0.08]
2010 0.200 ±0.005
[5.08 ±0.13]
0.100 ±0.003
[2.54 ±0.08]
0.025
[0.64]
0.020 ±0.003
[0.51 ±0.08]
0.097 ±0.003
[2.46 ±0.08]
2512 0.250 ±0.005
[6.35 ±0.13]
0.126 ±0.003
[3.20 ±0.08]
0.025
[0.64]
0.024 ±0.003
[0.61 ±0.08]
0.123 ±0.003
[3.12 ±0.08]
SIZE
b
a
Pulse Energy in mJoules
DIMENSIONS in inches [millimeters]
104
D
d
SOLDER PAD RECOMMENDATIONS in inches [millimeters]
INCH
a
b
l
1506
0.015 [0.38]
0.062 [1.57]
0.118 [3.00]
2010
0.023 [0.58]
0.100 [2.54]
0.153 [3.89]
2512
0.027 [0.69]
0.126 [3.20]
0.196 [4.98]
Pulse Energy Plot:
WSL2010E
This represents the energy in each of 50 pulses, with
a 1 second rest between pulses, that it takes to shift
the WSL....E resistance ± (0.50% + 0.01Ω).
103
WSL1506E
102
10
102
103
104
Pulse Energy
Temperature Rise In °C
105
Time in Microseconds
150
125
100
WSL1506E
WSL2010E
Rated Power In %
1
120
100
80
60
75
50
40
WSL2512E
20
25
0
0
0.25
Temperature Rise
0.50
0.75
1.0
Power in W
0
- 55
-25
0
25
50
Derating
75
70
100
125
150 175
Ambient Temperature in °C
PERFORMANCE
TEST
Thermal Shock
Short Time Overload
Low Temperature Storage
High Temperature Exposure
Moisture Resistance
Load Life
Vibration
Mechanical Shock
Resistance to Soldering Heat
Document Number 20033
Revision 11-Oct-02
CONDITIONS OF TEST
-55°C to +150°C, 100 cycles, 15 minutes at each extreme
5 x rated power for 5 seconds
-65°C for 24 hours
1000 hours @ +150°C
MIL-STD-202, Method 106, 0% power, 7a and 7b not required
1000 hours @ rated power, +70°C, 1.5 hours “ON”, 0.5 hours “OFF”
MIL-STD-202, Method 204D
100 G’s for 6 milliseconds, 5 pulses
+260°C solder, 10-12 seconds dwell, 25mm/second emergence
For Technical Questions in Europe contact: [email protected]
For Technical Questions in Americas/Asia contact: [email protected]
TEST LIMITS
±(0.20% +0.01Ω)
±(0.20% +0.01Ω)
±(0.20% +0.01Ω)
±(0.50% +0.01Ω)
±(0.50% +0.01Ω)
±(0.50% +0.01Ω)
±(0.10% +0.01Ω)
±(0.10% +0.01Ω)
±(0.50% +0.01Ω)
www.vishay.com
95