ICMIC X76F640AEG-2.7

This X76F640 device has been acquired by
IC MICROSYSTEMS from Xicor, Inc.
X76F640
64K
8Kx8+32x8
Secure Serial Flash
FEATURES
DESCRIPTION
•64-bit Password Security
—Five 64-bit Passwords for Read, Program
and Reset
•8192 Byte+32 Byte Password Protected Arrays
—Seperate Read Passwords
—Seperate Write Passwords
—Reset Password
•Programmable Passwords
•Retry Counter Register
—Allows 8 tries before clearing of both arrays
—Password Protected Reset
•32-bit Response to Reset (RST Input)
•32 byte Sector Program
•400kHz Clock Rate
•2 wire Serial Interface
•Low Power CMOS
—2.7 to 5.5V operation
—Standby current Less than 1µA
—Active current less than 3 mA
•High Reliability Endurance:
—100,000 Write Cycles
•Data Retention: 100 years
•Available in:
The X76F640 is a Password Access Security Supervisor,
containing one 65536-bit Secure Serial Flash array and
one 256-bit Secure Serial Flash array. Access to each
memory array is controlled by two 64-bit passwords.
These passwords protect read and write operations of
the memory array. A separate RESET password is used
to reset the passwords and clear the memory arrays in the
event the read and write passwords are lost.
The X76F640 features a serial interface and software
protocol allowing operation on a popular two wire bus.
The bus signals are a clock Input (SCL) and a bidirectional
data input and output (SDA). Access to the device
is controlled through a chip select (CS) input, allowing
any number of devices to share the same bus.
The X76F640 also features a synchronous response to reset
providing an automatic output of a hard-wired 32-bit
data stream conforming to the industry standard for
memory cards.
The X76F640 utilizes Xicor’s proprietary Direct Write
providing a minimum endurance of 100,000 cycles
TM
cell,
and a minimum data retention of 100 years.
—8 lead SOIC
—SmartCard Module
Functional Diagram
CS
CHIP ENABLE
DATA TRANSFER
SCL
SDA
INTERFACE
8K BYTE
SerialFlash ARRAY
ARRAY 0
(PASSWORD PROTECTED)
ARRAY ACCESS
ENABLE
LOGIC
32 BYTE
SerialFlash ARRAY
PASSWORD ARRAY
AND PASSWORD
ARRAY 1
(PASSWORD PROTECTED)
VERIFICATION LOGIC
RST
RESET
RESPONSE REGISTER
RETRY COUNTER
7025 FM 01
∧Xicor, Inc. 1994, 1995, 1996 Patents
Pending 7025-1.4 3/24/97 T2/C0/D1 SH
1
Characteristics subject to change without notice
X76F640
PIN DESCRIPTIONS
Data is transferred in 8-bit segments, with each transfer
being followed by an ACK, generated by the receiving
device.
Serial Clock (SCL)
The SCL input is used to clock all data into and out of the
device.
If the X76F640 is in a nonvolatile write cycle a “no A
CK”
(SDA=High) response will be issued in response to loading of the command byte. If a stop is issued prior to the
nonvolatile write cycle the write operation will be terminated and the part will reset and enter into a standby
mode.
Serial Data (SDA)
SDA is a true three state serial data input/output pin. Dur- ing a
read cycle, data is shifted out on this pin. During a
write cycle, data is shifted in on this pin. In all other
cases, this pin is in a high impedance state.
The basic sequence is illustrated in Figure 1.
Chip Enable (CS)
When CS is high, the X76F640 is deselected and the
SDA pin is at high impedance and unless an internal
write operation is underway, the X76F640 will be in
standby mode. CS low enables the X76F640, placing it in
the active mode.
PIN NAMES
Symbol
Reset (RST)
RST is a device reset pin. When RST is pulsed high
while CS is low the X76F640 will output 32 bits of fixed
data which conforms to the standard for “synchronous
response to reset”. CS must remain LOW and the part
must not be in a write cycle for the response to reset to
occur. See Figure 11. If at any time during the response
to reset CS goes HIGH, the response to reset will be
aborted and the part will return to the standby state. The
response to reset is "mask programmable" only!
Description
CS
Chip Select Input
SDA
Serial Data Input/Output
SCL
Serial Clock Input
RST
Reset Input
Vcc
Supply Voltage
Vss
Ground
NC
No Connect
7025 FM T01
PIN CONFIGURATION
Smart Card
DEVICE OPERATION
SOIC
There are two primary modes of operation for the
X76F640; Protected READ and protected WRITE.
Protected operations must be performed with one of four
8-byte passwords.
VSS
The basic method of communication for the device is
established by first enabling the device (CS LOW), generating a start condition, then transmitting a command,
followed by the correct password. All parts will be
shipped from the factory with all passwords equal to ‘0’. The
user must perform ACK Polling to determine the
validity of the password, before starting a data transfer
(see Acknowledge Polling.) Only after the correct password is accepted and a ACK polling has been performed, can
the data transfer occur.
1
8
VCC
CS
2
7
RST
SDA
3
6
SCL
NC
4
5
NC
VCC
GND
RST
CS
SCL
SDA
NC
NC
7025 FM 02
To ensure the correct communication, RST must remain LOW
under all conditions except when running a
“Response to Reset sequence”.
After each transaction is completed, the X76F640 will
reset and enter into a standby mode. This will also be the
response if an unsuccessful attempt is made to access a
protected array.
2
X76F640
Figure 1. X76F640 Device Operation
Start Condition
All commands are preceded by the start condition, which
is a HIGH to LOW transition of SDA when SCL is
LOAD COMMAND BYTE
HIGH. The X76F640 continuously monitors the SDA and SCL
lines for the start condition and will not respond to
any command until this condition is met.
LOAD 8-BYTE
PASSWORD
A start may be issued to terminate the input of a control
byte or the input data to be written. This will reset the
device and leave it ready to begin a new read or write
command. Because of the push/pull output, a start can-
VERIFY PASSWORD
ACCEPTANCE BY
USE OF PASSWORD ACK POLLING
not be generated while the part is outputting data. Starts are
inhibited while a write is in progress.
Stop Condition
All communications must be terminated by a stop condition.
The stop condition is a LOW to HIGH transition of
LOAD 2 BYTE ADDRESS
SDA when SCL is HIGH. The stop condition is also used to
reset the device during a command or data input
READ/WRITE
DATA BYTES
sequence and will leave the device in the standby power
mode. As with starts, stops are inhibited when outputting
data and while a write is in progress.
Twc OR DATA ACK POLLING
Acknowledge
Acknowledge is a software convention used to indicate
successful data transfer. The transmitting device, either
master or slave, will release the bus after transmitting
eight bits. During the ninth clock cycle the receiver will
pull the SDA line LOW to acknowledge that it received the
eight bits of data.
7025 FM 03
Retry Counter
The X76F640 contains a retry counter. The retry counter
allows 8 accesses with an invalid password before any
action is taken. The counter will increment with any combination of incorrect passwords. If the retry counter over-
The X76F640 will respond with an acknowledge after
recognition of a start condition and its slave address. If
flows, all memory areas are cleared and the device is
locked by preventing any read or write array password
matches. The passwords are unaffected. If a correct
password is received prior to retry counter overflow, the
both the device and a write condition have been
selected, the X76F640 will respond with an acknowledge
after the receipt of each subsequent eight-bit word.
retry counter is reset and access is granted. In order to reset
the operation of a locked up device, a special reset
command must be used with a RESET password.
Device Protocol
The X76F640 supports a bidirectional bus oriented protocol. The protocol defines any device that sends data
onto the bus as a transmitter and the receiving device as a
receiver. The device controlling the transfer is a master
Reset Device Command
The reset device command is used to clear the retry
counter and reactivate the device. When the reset device
command is used prior to the retry counter overflow, the
retry counter is reset and no arrays or passwords are
affected. If the retry counter has overflowed, all memory
areas are cleared and all commands are blocked and the
and the device being controlled is the slave. The master will
always initiate data transfers and provide the clock for
retry counter is disabled. Issuing a valid reset device
command (with reset password) to the device resets and
both transmit and receive operations. Therefore, the
X76F640 will be considered a slave in all applications.
re-enables the retry counter and re-enables the other
commands. Again, the passwords are not affected.
Clock and Data Conventions
Data states on the SDA line can change only during SCL
LOW. SDA changes during SCL HIGH are reserved for
Reset Password Command
A reset password command will clear both arrays and set all
passwords to all zero.
indicating start and stop conditions. Refer to Figure 2 and
Figure 3.
3
X76F640
Figure 2. Data Validity
SCL
SDA
Data Stable
Data
Change
7025 FM 04
Figure 3. Definition of Start and Stop Conditions
SCL
SDA
Start Condition
Stop Condition
7025 FM 05
Table 1. X76F640 Instruction Set
1st Byte
after Start
1st Byte
after
2nd Byte
after
Password
Password
Command Description
Password
used
1000 0000
High Address
Low address
Read (Array 0)
Read 0
1000 1000
High Address
Low address
Read (Array 1)
Read 1
1001 0000
High Address
Low address
Sector Write (Array 0)
Write 0
1001 1000
High Address
Low address
Sector Write (Array 1)
Write 1
1010 0000
0000 0000
0000 0000
Change Read 0 Password
Read 0
1010 1000
0000 0000
0000 0000
Change Read 1 Password
Read 1
1011 0000
0000 0000
0000 0000
Change Write 0 Password
Write 0
1011 1000
0000 0000
0000 0000
Change Write 1 Password
Write 1
1100 0000
0000 0000
0000 0000
Change Reset Password
Reset
1110 0000
not used
not used
Reset Password Command
Reset
1110 1000
not used
not used
Reset Device Command
Reset
1111 0000
not used
not used
ACK Polling command (Ends Password operation)
None
All the rest
Reserved
7025 FM T04
Notes:Illegal command codes will be disregarded. The part will respond with a “no-A CK” to the illegal byte and then return to the standby mode.
All write/read operations require a password.
4
X76F640
PROGRAM OPERATIONS
Sector Programming
The sector program mode requires issuing the 8-bit write
command followed by the password, password Ack command, the address and then the data bytes transferred as
illustrated in figure 4. Up to 32 bytes may be transferred. After the last byte to be transferred is acknowledged a stop condition is issued which starts the
nonvolatile write cycle.
START
Figure 4. Sector Programming
Write
Password
Write
Password
7
COMMAND
0
Wait tWC OR
Repeated
ACK Polling
Command
ACK
ACK
ACK
ACK
SDA S
A7
A6
A5
A4
A3
A2
A1
A0
ACK POLLING
COMMAND
A9
A8
A15
A14
A13
A12
A11
A10
START
If ACK, Then
Password Matches
Data 0
...
ACK
ACK
Data 31
STOP
ACK
ACK
5
ACK
S
ACK
NACK
S
Wait tWC Data
ACK Polling
7025 FM 07
X76F640
requires the master to perform an ACK polling with the
specific code of F0h. As with regular Acknowledge polling
the user can either time out for 10ms, and then issue the ACK
polling once, or continuously loop as described in the
flow.
ACK Polling
Once a stop condition is issued to indicate the end of the
host’s write sequence, the X76F640 initiates the internal
nonvolatile write cycle. In order to take advantage of the
typical 5ms write cycle, ACK polling can begin
immediately. This involves issuing the start condition
followed by the new command code of 8 bits (1st byte of
Password ACK Polling Sequence
the protocol.) If the X76F640 is still busy with the
nonvolatile write operation, it will issue a “no-A
CK” in response. If the nonvolatile write operation has
completed, an “ACK” will be returned and the host can
then proceed with the rest of the protocol.
PASSWORD LOAD
COMPLETED
ENTER ACK POLLING
ISSUE START
Data ACK Polling Sequence
WRITE SEQUENCE
COMPLETED
ISSUE
PASSWORD
ENTER ACK POLLING
ACK COMMAND
ISSUE START
ACK
RETURNED?
ISSUE NEW
COMMAND
NO
YES
CODE
PROCEED
ACK
RETURNED?
NO
7025 FM 09
If the password that was inserted was correct, then an
“ACK” will be returned once the nonvolatile cycle is over,
YES
PROCEED
in response to the ACK polling cycle immediately following
it.
7025 FM 08
If the password that was inserted was incorrect, then a “no
ACK” will be returned even if the nonvolatile cycle is over.
After the password sequence, there is always a nonvolatile write cycle. This is done to discourage random
Therefore, the user cannot be certain that the password is
incorrect until the 10ms write cycle time has elapsed.
guesses of the password if the device is being tampered
with. In order to continue the transaction, the X76F640
6
X76F640
Figure 5. Acknowledge Polling
SCL
8th clk.
of 8th
8th
clk
‘ACK’
clk
pwd. byte
SDA
‘ACK’
clk
8th bit
‘ACK’
ACK or
no ACK
START
condition
7025 FM 10
READ OPERATIONS
Sequential Read
The host can read sequentially within an array after the
password acceptance sequence. The data output is
sequential, with the data from address n followed by the
data from n+1. The address counter for read operations
Read operations are initiated in the same manner as write
operations but with a different command code.
Random Read
The master issues the start condition and a Read instruction
and password, performs a Password Ack Polling, then
increments all address bits, allowing the entire memory
array contents to be serially read during one operation. At
the end of the address space (address 1FFFh for array 0, 1Fh
for array 1), the counter “rolls o
ver” to address 0 and
the X76F640 continues to output data for each acknowl- edge
received. Refer to figure 7 for the address, acknowledge and data transfer sequence. An acknowledge must
follow each 8-bit data transfer. After the last bit has been
issues the word address. Once the password has been
acknowledged and first byte has been read, another start
can be issued followed by a new 8-bit address. Random
reads are allowed, but only the low order 8 bits can
change. This limits random reads to a 256 byte block.
Therefore, with a single password cycle only a 256 byte
block of array 0 may be accessed randomly. To randomly
access another block of array 0, a stop must be issued fol-
read, a stop condition is generated without a preceding
acknowledge.
lowed by a new command/address/password sequence. A
random read of the array 1 can access all locations without another password command sequence.
START
Figure 6. Random Read
Read
Password
Read
Password
7
COMMAND
0
Wait tWC OR
ACK
ACK
ACK
ACK
SDA S
Repeated
ACK Polling
Command
Data X
STOP
S
ACK
ACK
ACK
S
ACK
NACK
S
A7
A6
A5
A4
A3
A2
A1
A0
START
A7
A6
A5
A4
A3
A2
A1
A0
ACK POLLING
COMMAND
A9
A8
A15
A14
A13
A12
A11
A10
START
If ACK, then
Password Matches
Data Y
7025 FM 11
7
X76F640
START
Figure 7. Sequential Read
Read
Password
Read
Password
7
COMMAND
Wait tWC
OR
0
Repeated
ACK Polling
Command
ACK
ACK
ACK
ACK
SDA S
STOP
ACK
ACK
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
ACK POLLING
COMMAND
A15
A14
A13
A12
A11
A10
START
If ACK, then
Password Matches
S
ACK
ACK
ACK
NACK
S
Data X
Data 0
7025 FM 12
PASSWORDS
After this time, it cannot be determined if the password has
been loaded correctly, without trying the new pass-
The sequence in Figure 8 shows how to change (program) the passwords. The programming of passwords is
done twice prior to the nonvolatile write cycle in order to verify
that the new password is consistent. After the eight
word. To determine if the new password has been loaded
correctly the data ACK polling command is issued immediately following the stop bit. If it returns an ACK, then the two
passes of the new password entry do not match. If it
bytes are entered in the second pass, a comparison takes
place. A mismatch will cause the part to reset and
enter into the standby mode.
returns a "no ACK" then the passwords match and a high
voltage cycle is in progress. The high voltage cycle is
complete when a subsequent data ACK command
returns an "ACK".
Data ACK polling can be used to determine if a password has
been loaded correctly, however the data ACK command must be issued less than 2ms after the stop bit.
There is no way to read any of the passwords.
START
Figure 8. Change Passwords
Old
Password
Old
Password
7
COMMAND
0
Wait tWC OR
Repeated
ACK Polling
Command
START
If ACK, then
Password Matches
ACK
ACK
ACK
ACK
SDA S
New
Password
ACK POLLING
COMMAND
7
Two bytes of “0”
Password
7
Password
0
Password
0
STOP
Data ACK
Polling
New
New
ACK
ACK
NACK
ACK
ACK
S
ACK
ACK
ACK
ACK
ACK
S
If immediate ACK,
then New Password error
If immediate NACK,
followed by ACK after ~5ms
then New Password OK
7025 FM 13
8
X76F640
Figure 9. Reset Password
Reset
Password
0
7
SDA S
STOP
Reset Password
COMMAND
If ACK, then
Device reset
Repeated
ACK Polling
Command
START
ACK POLLING
COMMAND
S
NACK
ACK
ACK
ACK
ACK
S
ACK
START
Wait tWC
OR
Reset
Password
7025 FM 14
SDA S
STOP
0
7
If ACK, then
Device reset
Repeated
ACK Polling
Command
Reset
Password
Reset
Password
Reset Device
COMMAND
Wait tWC
OR
START
ACK POLLING
COMMAND
S
NACK
ACK
ACK
ACK
ACK
S
ACK
START
Figure 10. Reset Device
7025 FM 15
Figure 11. Response to RESET (RST)
CS
RST
SCK
SO
3322222
1098765
2
4
2222111
3210987
1
6
111111
543210
9 8
7654321
0
7025 FM 16
ABSOLUTE MAXIMUM RATINGS*
*COMMENT
Temperature under Bias......................–65°C to +135°C
Storage Temperature...........................–65°C to +150°C
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation of the
device at these or any other conditions above those
Voltage on any Pin with
Respect to VSS ......................................
–1V to +7V
D.C. Output Current..................................................
5mA
listed in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Lead Temperature (Soldering,
.................................300°C
10 seconds)
9
X76F640
RECOMMENDED OPERATING CONDITIONS
Temp
Min.
Max.
Supply Voltage
Limits
0°C
+70°C
X76F640
4.5V to 5.5V
–20°C
+85°C
X76F640 – 2.7
2.7V to 3.6V
Commercial
Extended
7025 FM T05
7025 FM T06
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Symbol
Limits
Min.
Max.
Parameter
Units
Test Conditions
fSCL = VCC x 0.1/VCC x 0.9 Levels @ 400 KHz, SDA =
Open
VCC Supply Current
(Read)
1
ICC2 (3)
VCC Supply Current
(Write)
3
ISB1 (1)
VCC Supply Current
(Standby)
50
∝A
VIL = VCC x 0.1, VIH = VCC x 0.9 fSCL =
400 KHz, fSDA = 400 KHz
ISB2 (1)
VCC Supply Current
(Standby)
1
∝A
VSDA = VSCC = VCC Other =
GND or VCC–0.3V
ILI
Input Leakage Current
10
∝A
VIN = VSS to VCC
10
∝A
VOUT = VSS to VCC
VCC x 0.3
V
VCC = 5.5V
V
VCC = 5.5V
V
VCC = 3.0V
V
VCC = 3.0V
V
IOL = 3mA
ICC1
ILO
RST = CS = VSS
mA
fSCL = VCC x 0.1/VCC x 0.9 Levels @ 400 KHz, SDA =
Open
RST = CS = VSS
Output Leakage Current
VIL1 (2)
Input LOW Voltage
(2)
Input HIGH Voltage
VIL2 (2)
Input LOW Voltage
VIH2 (2)
Input HIGH Voltage
VOL
Output LOW Voltage
VIH1
mA
–0.5
VCC x 0.7VCC + 0.5
–0.5
VCC x 0.1
VCC x 0.9VCC + 0.5
0.4
7002 FM T07
CAPACITANCE TA = +25°C, f = 1MHz, VCC = 5V
Symbol
Test
Max.
Units
COUT (3)
Output Capacitance (SDA)
8
pF
Conditions
VI/O = 0V
CIN (3)
Input Capacitance (RST, SCL, CS)
6
pF
VIN = 0V
7002 FM T08
NOTES: (1) Must perform a stop command after a read command prior to measurement
(2) VIL min. and VIH max. are for reference only and are not tested.
(3) This parameter is periodically sampled and not 100% tested.
EQUIVALENT A.C. LOAD CIRCUIT
A.C. TEST CONDITIONS
Input Pulse Levels
5V
3V
1533Ο
OUTPUT
Input Rise and Fall Times
1.3KΟ
Input and Output Timing Level
Output Load
OUTPUT
100pF
100pF
VCC x 0.1 to VCC x 0.9
10ns
VCC x 0.5
100pF
7002 FM T09
7025 FM 17
10
X76F640
AC CHARACTERISTICS
AC Specifications (Over the recommended operating conditions)
Symbol
Parameter
Min
Typ
(1)
Max
Units
400
KHz
fSCL
SCL Clock Frequency
tIN (1)
Pulse width of spikes which must be suppressed by the
input filter
50
100
tAA
SCL LOW to SDA Data Out Valid
0.1
0.3
tBUF
Time the bus must be free before a new transmit can
start
1.3
∝s
tLOW
Clock LOW Time
1.3
∝s
tHIGH
Clock HIGH Time
0.6
∝s
tSU:STA
Start Condition Setup Time
0.6
∝s
tHD:STA
Start Condition Hold Time
0.6
∝s
tSU:DAT
Data In Setup Time
100
ns
0
∝s
∝s
0
tHD:DAT
Data In Hold Time
tSU:STO
Stop Condition Setup Time
0.6
tDH
Data Output Hold Time
50
ns
0.9
300
∝s
ns
(2)
300
ns
300
ns
tR
SDA and SCL Rise Time
20 + 0.1 x Cb
tF
SDA and SCL Fall Time
20 + 0.1 x Cb (2)
tSU:CS
CS Setup Time
200
ns
tHD:CS
CS Hold Time
100
ns
fSCL_RST
SCL Clock Frequency during Response to Reset
tSR
Device Select to RST active
200
tNOL
RST to SCL Non-Overlap
500
ns
400
kHz
ns
tRST
RST High Time
2.25
∝s
tSU:RST
Response to Reset Setup Time
1.25
∝s
tLOW_RST
Clock LOW during Response to Reset
1.25
∝s
tHIGH_RST
Clock HIGH during Response to Reset
1.25
∝s
tRDV
RST LOW to SDA Valid During Response to Reset
0
500
ns
tCDV
CLK LOW to SDA Valid During Response to Reset
0
500
ns
tDHZ
Device Deselect to SDA high impedance
0
500
ns
Notes:1.
Typical values are for TA = 25˚C and VCC = 5.0V
Notes:2.
Cb = Total Capacitance of one bus line in pf.
7025 FM T14
11
X76F640
RESET AC SPECIFICATIONS
Power Up Timing
Symbol
Parameter
Min.
Typ
(2)
Max.
Units
tPUR (1)
Time from Power Up to Read
1
mS
tPUW (1)
Time from Power Up to Write
5
mS
7025 FM T11
Notes:1.
2.
Delays are measured from the time VCC is stable until the specified operation can be initiated. These parameters are periodically sampled and not
100% tested.
Typical values are for TA = 25˚C and VCC = 5.0V
Nonvolatile Write Cycle Timing
Symbol
tWC (1)
Parameter
Min.
Write Cycle Time
Typ.(1)
Max.
Units
5
10
mS
7025 FM T12
Notes:1.
tWC is the time from a valid stop condition at the end of a write sequence to the end of the self-timed internal nonvolatile write cycle. It is the
minimum cycle time to be allowed for any nonvolatile write by the user, unless Acknowledge Polling is used.
TIMING DIAGRAMS
Bus Timing
tR
tF
SCL
tHIGH
tLOW
tSU:DAT
tSU:STA
tHD:DAT
tSU:STO
tHD:STA
SDA IN
tAA
tDH
tBUF
SDA OUT
7025 FM 18
Write Cycle Timing
SCL
SDA
8th bit of last byte
ACK
tWC
Stop
Condition
Start
Condition
7025 FM 19
12
X76F640
CS Timing Diagram (Selecting/Deselecting the Part)
SCL
tHD:CS
tSU:CS
CS
from
master
7025 FM 20
RST Timing Diagram – Response to a Synchronous Reset
tSR
CS
RST
tRST
tNOL
tHIGH_RST
tNOL
1st
clk
CLK
2nd
clk
pulse
pulse
tSU:RST
tRDV
I/O
3rd
clk
tLOW_RST
pulse
tCDV
DATA BIT (2)
DATA BIT (1)
CS
RST
CLK
tDHZ
I/O
DATA BIT (N+1)
DATA BIT (N)
(N+2)
7025 FM 21
Pull Up Resistance in KΟ
GUIDELINES FOR CALCULATING TYPICAL VALUES OF BUS PULL UP RESISTORS
100
80
60
V
CCMAX
R
MIN
RMAX
40
20
MAX
40
60
80 100
20
Bus capacitance in pF
OLMIN
t
R
R
RMIN
= -------------------------= 1.8KΟ
I
= ---------------C
BUS
tR = maximum allowable SDA rise time
7025 FM 22
13
X76F640
8-LEAD PLASTIC, 0.200” WIDE SMALL OUTLINE
GULLWING PACKAGE TYP “A” (EIAJ SOIC)
0.020 (.508)
0.012 (.305)
.213
(5.41) .205
(5.21)
.330
(8.38) .300
(7.62)
PIN 1 ID
.050 (1.27) BSC
.212
(5.38) .203
(5.16)
.080
(2.03) .070
(1.78)
.013
(.330) .004
(.102)
0
8
REF
.010
(.254) .007
(.178)
.035
(.889) .020
(.508)
NOTE:
1. ALL DIMENSIONS IN INCHES (IN P ARENTHESES IN MILLIMETERS) 2.
PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH
7025 FM 24
14
X76F640
8 PAD CHIP ON BOARD SMART CARD MODULE TYPE X
0.465 ± 0.002
(11.81 ± 0.05)
0.088 (2.24) MIN EPOXY
FREE AREA (TYP.)
0.285 (7.24) MAX.
R. 0.039 (1.00) (4X)
0.069 (1.75) MIN EPOXY
FREE AREA (TYP.)
0.270 (6.86) MAX.
0.420 ± 0.002
(10.67 ± 0.05)
A
A
0.008 ± 0.001
(0.20 ± 0.03)
0.210 ± 0.002
(5.33 ± 0.05)
0.233 ± 0.002
(5.92 ± 0.05)
SECTION A-A
DIE
0.0235 (0.60) MAX.
GLOB SIZE
0.015 (0.38) MAX.
0.008 (0.20) MAX.
FR4 TAPE
COPPER, NICKEL PLATED, GOLD FLASH
0.146 ± 0.002
(3.71 ± 0.05)
0.105 ± 0.002
(2.67 ± 0.05)
0.174 ± 0.002
(4.42 ± 0.05)
R. 0.013 (0.33) (8x)
TYP.
(8x)
0.105 ± 0.002
(2.67 ± 0.05)
(8x)
NOTE:
1. ALL DIMENSIONS IN INCHES AND (MILLIMETERS)
3003 ILL 03.1
15
X76F640
SMART CARD TYPE Y
3.369 ± 0.002
(85.57 ± 0.05)
3° MAX.
DRAFT ANGLE
(ALL AROUND)
0.593 ± 0.002
(15.06 ± 0.05)
0.430 ± 0.002
(10.92 ± 0.05)
R. 0.125
(3.18) (4x)
A
0.475 ± 0.010
(12.07 ± 0.25)
2.125 ± 0.002
(53.98 ± 0.05)
A
R. 0.030 (0.76) (4x)
0.31 ± 0.0005
(.079 ± 0.0127)
0.478 ± 0.002
(12.14 ± 0.05)
MOLD GATE DETAIL
SECTION A-A
SCALE: 5x
NOTES:
1. ALL DIMENSIONS ARE IN INCHES AND (MILLIMETERS).
2. MATERIAL: WHITE PVC MOLDED PLASTIC WITH ANTI-STATIC ADDITIVE. 3.
SURFACE FINISH SUITABLE FOR OFFSET PRINTING.
3003 ILL 02.1
16
X76F640
ORDERING INFORMATION
X76F640
P
T
G –V
VCC Limits
Blank = 5V ±10% 2.7
= 2.7V to 3.6V
Device
G=RoHS Compliant Lead Free package
Blank = Standard package. Non lead free
Temperature Range
Blank = Commercial = 0°C to +70°C
E = Extended = –20°C to +85°C
Package
A = 8-Lead SOIC (EIAJ)
H = Die in Waffle Packs
W = Die in Wafer Form
X = Smart Card Module
Y = Smart Card
LIMITED WARRANTY
Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express,
statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Xicor, Inc. makes no
warranty of merchantability or fitness for any purpose. Xicor, Inc. reserves the right to discontinue production and change specifications and prices at any time and without
notice.
Xicor, Inc. assumes no responsibility for the use of any circuitry other than circuitry embodied in a Xicor, Inc. product. No other circuits, patents, licenses are implied.
U.S. PATENTS
Xicor products are covered by one or more of the following U.S. Patents: 4,263,664; 4,274,012; 4,300,212; 4,314,265; 4,326,134; 4,393,481; 4,404,475; 4,450,402;
4,486,769; 4,488,060; 4,520,461; 4,533,846; 4,599,706; 4,617,652; 4,668,932; 4,752,912; 4,829, 482; 4,874, 967; 4,883, 976. Foreign patents and additional patents pending.
LIFE RELATED POLICY
In situations where semiconductor component failure may endanger life, system designers using this product should design the system with appropriate error detec- tion and
correction, redundancy and back-up features to prevent such an occurence.
Xicor’s products are not authorized for use in critical components in life support devices or systems.
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform,
when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life sup- port device
or system, or to affect its safety or effectiveness.
17